SPBD-1250F4Q2R - Delta Electronics Inc.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

1 Revision: S0

12/20/2007

www.deltaww.com

Intelligent SFP Bi-Directional Transceiver

Module for Gigabit Ethernet and Fast Ethernet

FEATURES

z RoHS compliant

z Digital Diagnostic SFF-8472 MSA compliant

z Simplex SC connector with 1550nm

Transmitter and 1310nm Receiver

z Single + 3.3V power supply and TTL logic

interface

z Bellcore GR-468 compliant

z Laser class 1 product which comply with the

requirements of IEC 60825-1 and IEC 60825-2

Description

The SPBD-1250xxxx series are hot pluggable

3.3V Small-Form-Factor (SFP) Bi-Directional

transceiver module designed expressly for

high-speed communication applications that

require rates of up to 1250Mbit/sec. It is compliant

with the Gigabit Ethernet and Fast Ethernet

standards, as well as the SFP Multisource

Agreement (MSA).

The SPBD-1250xxxx transceivers provide with

the SC receptacle that is compatible with the

industry standard SC connector. The transceiver is

also compatible with industry standard RFT

connector and cage. It also includes a LOS (Loss

Of Signal) circuit that provides a TTL logic-high

output when an unusable optical signal level is

detected.

The module includes 1550nm un-cool DFB

laser, InGaAs PIN, Preamplifer and WDM filter in a

high-integrated optical assembly for high-density

system application. The SFP Bi-Directional

transceiver can upgrade transmission capacity very

convenient without installing new fibers.

Application

z IEEE 802.3ah 1000BASE-BX

z Gigabit Ethernet

z FTTx WDM Broadband Access

z Switch to switch/backbone interface

Performance

z SPBD-1250F4Q2R data link up to 10km in

9/125um single mode fiber.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

2 Revision: S0

12/20/2007

www.deltaww.com

1. Absolute Maximum Ratings

Parameter Symbol Min. Typ. Max. Unit Note

Storage Temperature Ts -40 85 ºC

Storage Ambient Humidity HA 5 95 %

Power Supply Voltage VCC 0 5 V

Signal Input Voltage -0.3 Vcc+0.3 V

Optical Input Power (Peak) +3 dBm

2. Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Note

Operating Case Temperature TC -5 75 ºC Note (1)

Ambient Humidity HA 5 85 %

Non-condensing

Power Supply Voltage VCC 3.13 3.3 3.47 V

Power Supply Current ICC 300 mA

Power Supply Noise Rejection 100 mVp-p 100Hz to 1MHz

Data Rate 1250

-100ppm 1250 1250

+100ppm Mbps

Transmission Distance 10 km

Note (1). Measured on topside of case front center.

3. Specification of Transmitter

Parameter Symbol Min. Typ. Max. Unit Note

Average Launched Power PO -9 -6 -3 dBm Note (1)

Optical Extinction Ratio ER 9 dB

Center Wavelength C 1530 1550 1570 nm DFB Laser

Spectrum Width (-20dB)  0.88 nm

Side Mode Suppression Ratio SMSR 30 dB

Transmitter OFF Output Power POff -45

dBm

Optical Rise/Fall Time tr/tf 260 ps Note (2)

Deterministic Jitter DJ 80 ps

Total Jitter TJ 227 ps Note (3)

Relative Intensity Noise RIN12OMA -113 dB/Hz

Optical Return Loss Tolerance ORLT 12 dB

Transmitter Reflectance -10 dB

Output Eye Mask

{X1,X2,Y1,Y2,Y3}

Compliant with IEEE 802.3ah standard

{0.22,0.375,0.20,0.20,0.30} Note (4)

Note (1). Launched power (avg.) is power coupled into a single mode fiber.

Note (2). These are unfiltered 20-80% values.

Note (3). Measure at 27-1 NRZ PRBS pattern.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

3 Revision: S0

12/20/2007

www.deltaww.com

Note (4). Eye Mask definition

4. Specification of Receiver

Parameter Symbol Min. Typ. Max. Unit Note

Input Optical Wavelength λIN 1260 1360 nm PIN-PD

Receiver Sensitivity PIN -23

dBm Note (1)

Input Saturation Power (Overload) PSAT -3 dBm

LOS-Deassert Power PA - -24 dBm

LOS-Assert Power PD -44 dBm Note (2)

LOS Hysteresis PA-PD 0.5 2 6 dB

Receiver Reflectance -12 dB Note (3)

Deterministic Jitter DJ 170 ps

Total Jitter TJ 266 ps

Output Data Rise/Fall time tr/tf 260 ps Note (4)

Note (1). Measured with 1310nm, ER=9dB; BER =<10-12@PRBS=27-1 NRZ

Note (2). When LOS asserted, the data output is Low-level (fixed)

Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the

optical signal with a central wavelength of 1310nm transmitted to terminal.

Note (4). These are 20%~80% values

X1 X2 1-X2 1-X1

1+ Y 3

1- Y1

0.5

- Y2

ormalized Time

Normalized Amplitude

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

4 Revision: S0

12/20/2007

www.deltaww.com

5. Electrical Interface Characteristics

Parameter Symbol Min. Typ. Max. Unit Note

Transmitter

Total Supply Current ICC A mA Note (1)

Differential Data Input Swing VDT 500 2400 mVp-p

Differential line input Impedance RIN 80 100 120 Ohm

Transmitter Disable Input-High VDISH 2 VCC V Note (2)

Transmitter Disable Input-Low VDISL 0 0.8 V

Transmitter Fault Output-High VTXFH 2 VCC+0.3 V

Transmitter Fault Output-Low VTXFL 0 0.8 V

Transmitter Fault Pull up Resistor RTX_FAULT 4.7 10 k Note (3)

Receiver

Total Supply Current ICC B mA Note (1)

Differential Data Output Swing VDR 400 1200 mVp-p Note (4)

LOS Output Voltage-High VLOSH 2 VCC+0.3 V

LOS Output Voltage-Low VLOSL 0 0.8 V

Receiver LOS Load RRXLOS 4.7 10 k Note (3)

Note (1). A (TX)+ B (RX) = 300mA

(A: Not include termination circuit; B: using a resister of 150 between Data-output and ground)

Note (2). There is an internal 4.7 to 10k pull-up resistor to VccT.

Note (3). Pull up to VCC on host Board.

Note (4). Internally AC coupled output, but requires a 100Ohm differential termination at or internal to

Serializer/ Deserializer.

6. Digital Diagnostic Monitor Accuracy

Parameter Accuracy Unit Calibration Note

Transceiver Internal Temperature ± 3℃ ℃ Internal TC=-5~+75℃

Power Supply Internal Voltage ± 3% V Internal VCC=3.3V±5%

TX Bias Current ± 10% mA Internal Specified by nominal bias value

TX Optical Power ± 3dB dBm Internal -9 to -3dBm

RX Optical Power ± 3dB dBm Internal -23 to -3dBm

Note. Temperature and Voltage is measured internal to the transceiver.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

5 Revision: S0

12/20/2007

www.deltaww.com

7. Pin Description

SFP Transceiver Electrical Pad Layout Host Board Connector Pad Layout

Pin Function Definitions

Pin Num. Name Function Plug Seq. Notes

1 VeeT Transmitter Ground 1 Note (1)

2 TX Fault Transmitter Fault Indication 3 Note (2)

3 TX Disable Transmitter Disable 3 Note (3)

4 MOD-DEF2 Module Definition 2 3 Note (4), 2 wire serial ID interface

5 MOD-DEF1 Module Definition 1 3 Note (4), 2 wire serial ID interface

6 MOD-DEF0 Module Definition 0 3 Note (4), Grounded in Module

7 Rate Select Not Connect 3 Function not available

8 LOS Loss of Signal 3 Note (5)

9 VeeR Receiver Ground 1

10 VeeR Receiver Ground 1

11 VeeR Receiver Ground 1

12 RD- Inv. Received Data Out 3 Note (6)

13 RD+ Received Data Out 3 Note (6)

14 VeeR Receiver Ground 1

15 VccR Receiver Power 2 Note (7)

16 VccT Transmitter Power 2 Note (7)

17 VeeT Transmitter Ground 1

18 TD+ Transmit Data In 3 Note (8)

19 TD- Inv. Transmit Data In 3 Note (8)

20 VeeT Transmitter Ground 1

Plug Seq.: Pin engagement sequence during hot plugging.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

6 Revision: S0

12/20/2007

www.deltaww.com

Notes:

1) Circuit ground is internally isolated from frame (chassis) ground. Tx GND and Rx GND may be internally isolated

within the TRx module.

2) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K~10K resistor on the host board.

Pull up voltage between 2.0V and VccT+0.3V. The output indicates Low when the transmitter is operating

normally, and High with a laser fault including laser end-of-life. In the low state, the output will be pulled to less

than 0.8V.

3) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module

with a 4.7 – 10 K  resistor. Its states are:

Low (0 – 0.8V): Transmitter on

(>0.8, < 2.0V): Undefined

High (2.0 – 3.465V): Transmitter Disabled

Open: Transmitter Disabled

4) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10Kresistor on the

host board. The pull-up voltage shall be VccT or VccR.

Mod-Def 0 is grounded by the module to indicate that the module is present

Mod-Def 1 is the clock line of two-wire serial interface for serial ID

Mod-Def 2 is the data line of two-wire serial interface for serial ID

5) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10K resistor.

Pull up voltage between 2.0V and VccR+0.3V. When high, this output indicates the received optical power is

below the worst-case receiver sensitivity. Low indicates normal operation. In the low state, the output will be

pulled to less than 0.8V.

6) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be

terminated with 100 (differential) at the user SERDES. The AC coupling is done inside the module and is thus

not required on the host board.

7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP

connector pin. Recommended host board power supply filtering is shown below page. Inductors with DC

resistance of less than 1 Ohm should be used in order to maintain the required voltage at the SFP input pin with

3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP

transceiver module will result in an inrush current of no more than 30 mA greater than the steady state value.

8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 

differential termination inside the module. The AC coupling is done inside the module and is thus not

required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200

mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 –

600 mV single-ended) be used for best EMI performance.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

7 Revision: S0

12/20/2007

www.deltaww.com

8. Recommend Interface Circuit

Laser Diode

Photo Diode

1uH

0.1uF10uF

0.1uF

0.01uF

0.1uF10uF

RES1

100 Ohms*

RES1 RES1 RES1

10k Ohms

100 Ohms

VCC

Protocol Vcc

SerDes ICProtocol IC

PLD / PAL Mod_def 2

Mod_def 1

Mod_def 0

3.3V

DELTA SFP Module

Preamp &

Tx_Disable

Quantizer

Tx_Fault

TD +

TD -

VeeT

RD +

RD -

Rx_LOS

VeeR

Tx_Disable

Tx_Fault

Rx_LOS

RES1 = 4.7k to 10k Ohms

VccT

VccR

Laser Driver

* Depands on SerDes IC used

EEPROM

SFP Host Board Schematic

Recommended Host Board Supply Filtering Network

Design criterion of the capacitor used is the

resonant frequency and its value must be in the

order of the nominal data rate. Short trace

lengths are mandatory.

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

8 Revision: S0

12/20/2007

www.deltaww.com

9. Outline Dimensions

Tx/Rx Wavelength Latch Color Identifier

1310nm/1550nm Black

1550nm/1310nm Yellow

1310nm/1490nm Blue

1490nm/1310nm Violet

Week (52Weeks/Year) : 1月2日=01

XXXXXXXXXXX

1040.10 and 1040.11

Made in x

Complies with 21 CFR

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

9 Revision: S0

12/20/2007

www.deltaww.com

10. Enhanced Digital Diagnostic Interface

The memory map in the following describes an extension to the memory map defined in SFF-8472.

The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic

information about the module’s present operating conditions.

2 wire address 1010000 X (A0h) 2 wire address 1010001 X (A2h)

0 0

Alarm and Warning Thresholds

(56 bytes)

Serial ID Defined by SFP MSA

(96 bytes) 56

Cal Constants

(40 bytes)

96 96

119

Real Time Diagnostic Interface

(24 bytes)

127

Vender Specific

(32 bytes) 120

127

Vender Specific

128 128

247

User Writable EEPROM

(120 bytes)

255

Reserved in SFP MSA

(128 bytes)

248

255

Vender Specific

(8 bytes)

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

10 Revision: S0

12/20/2007

www.deltaww.com

EEPROM Serial ID Memory Contents (2-Wire Address A0h)

Address Name of Field Value (Hex) Remark

Base ID Fields

00 Identifier 03 SFP transceiver

01 Ext. Identifier 04 Serial ID module supported

02 Connector 01 SC connector

03 00 Infiniband Compliance Codes

04-05 Transceiver code 00 00 Transceiver codes

06 Transceiver code 40 Ethernet Base-BX10 compliance

07-10 Transceiver code 00 00 00 00 Transceiver codes

11 Encoding 01 Compatible with 8B10B GE encoding code

12 BR, Nominal 0D Nominal 1300 Mbps (actual GE 1250Mbps)

13 Reserved 00 Reserved for SFF-8079

14 0A 9/125 ìm fiber, units of km (10km)

15 64 9/125 ìm fiber, units of 100 m (10000m)

16 00 50/125 ìm fiber, units of 10 m

17 00 62.5/125 ìm fiber, units of 10 m

18 00 Link length supported for copper, units of meters

19 00 Reserved

20 44 “D” (Vendor name in ASCII character)

21 45 “E” (Vendor name in ASCII character)

22 4C “L” (Vendor name in ASCII character)

23 54 “T” (Vendor name in ASCII character)

24 41 “A” (Vendor name in ASCII character)

25-35

Vendor Name

20 (Vendor name in ASCII character)

36 Channel spacing 00 Specify the channel spacing in units of GHz.

37-39 Vendor OUI 00 SFP vendor IEEE company ID

40 53 “S” (Vendor P/N in ASCII character)

41 50 “P” (Vendor P/N in ASCII character)

42 42 “B” (Vendor P/N in ASCII character)

43 44 “D” (Vendor P/N in ASCII character)

44 2D “-“ (Vendor P/N in ASCII character)

45 31 “1” (Vendor P/N in ASCII character)

46 32 “2” (Vendor P/N in ASCII character)

47 35 “5“ (Vendor P/N in ASCII character)

48 30 “0” (Vendor P/N in ASCII character)

49 46 “F” (Vendor P/N in ASCII character)

50 34 “4” (Vendor P/N in ASCII character)

51 51 “Q (Vendor P/N in ASCII character)

52 32 “2 (Vendor P/N in ASCII character)

53 52 “R” (Vendor P/N in ASCII character)

54 20 (Vendor P/N in ASCII character)

Vendor P/N

20 (Vendor P/N in ASCII character)

56-59 Vendor Rev 41 20 20 20 “A”

60-61 LD wavelength 06 0E (1550nm)

62 DWDM wavelength 00

63 CC_BASE XX Check sum (0~62)

Extended ID Fields

64 Reserved 00

65 Options 1A

(Tx_Diasble, Tx_Fault, LOS)

66 BR,max 00 Upper bit rate margin,units of %

67 BR,min 00 Lower bit rate margin,units of %

68-83 Vendor SN XX “DEYYWWVVRSSSSS”

84-91 Date code XX “YYMMDD”

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

11 Revision: S0

12/20/2007

www.deltaww.com

92 DDM 68 Diagnostics (Internally Calibrated)

93 Enhanced options B0 (Soft Tx_Fault, Soft LOS)

94 SFF-8472

compliance 01 SFF-8472 Compliance Rev.9.3

95 CC_EXT XX Check sum (64~94)

Vendor Specific ID Fields

96-127 Vendor Specific 00 Vendor Specific EEPROM

128-255 Reserved 00 Reserved for SFF-8079

Digital Diagnostic Monitoring Interface (2-Wire Address A2h)

Alarm and Warning Thresholds (2 Wire Address A2h)

Address # Bytes Name HEX Real Value Unit Note

00-01 2 Temp High Alarm 5A 00 90 ºC

02-03 2 Temp Low Alarm EC 00 -20 ºC

04-05 2 Temp High Warning 50 00 80 ºC

06-07 2 Temp Low Warning F6 00 -10 ºC

08-09 2 Voltage High Alarm 94 70 3.8 V

10-11 2 Voltage Low Alarm 6D 60 2.8 V

12-13 2 Voltage High Warning 87 8C 3.47 V

14-15 2 Voltage Low Warning

7A 44 3.13 V

16-17 2 Bias High Alarm 61 A0 50 mA

18-19 2 Bias Low Alarm 01 F4 1 mA

20-21 2 Bias High Warning 4E 20 40 mA

22-23 2 Bias Low Warning 01 F4 1 mA

24-25 2 TX Power High Alarm 27 10 0 dBm

26-27 2 TX Power Low Alarm 02 77 -12 dBm

28-29 2 TX Power High Warning 13 94 -3 dBm

30-31 2 TX Power Low Warning 04 EB -9 dBm

32-33 2 RX Power High Alarm 27 10 0 dBm

34-35 2 RX Power Low Alarm 0019 -26 dBm

36-37 2 RX Power High Warning 13 94 -3 dBm

38-39 2 RX Power Low Warning 00 32 -23 dBm

40-55 16 Reserved

Notes:

1) TC: Operating Case temperature

2) Ibias: Bias current at room temperature. The min. setting current is 0 mA.

3) PO: Operating optical power of transmitter at room temperature.

4) PSAT: Overload optical power of receiver

5) PIN: Sensitivity optical power of receiver

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

12 Revision: S0

12/20/2007

www.deltaww.com

Calibration Constants (2 Wire Address A2h)

Address # Bytes Name HEX Description

56-59 4 Rx_PWR (4) 00 00 00 00 Rx_PWR (4) is set to zero for “internally calibrated” devices.

60-63 4 Rx_PWR (3) 00 00 00 00 Rx_PWR (3) is set to zero for “internally calibrated” devices.

64-67 4 Rx_PWR (2) 00 00 00 00 Rx_PWR (2) is set to zero for “internally calibrated” devices.

68-71 4 Rx_PWR (1) 3F 80 00 00 Rx_PWR (1) is set to 1 for “internally calibrated” devices.

72-75 4 Rx_PWR (0) 00 00 00 00 Rx_PWR (0) is set to zero for “internally calibrated” devices.

76-77 2 Tx_I (Slope) 01 00 Tx_I (Slope) is set to 1 for “internally calibrated” devices.

78-79 2 Tx_I (Offset) 00 00 Tx_I (Offset) is set to zero for “internally calibrated” devices.

80-81 2

Tx_PWR (Slope) 01 00 Tx_PWR (Slope) is set to 1 for “internally calibrated”

devices.

82-83 2

Tx_PWR

(Offset) 00 00 Tx_PWR (Offset) is set to zero for “internally calibrated”

devices.

84-85 2 T (Slope) 01 00 T (Slope) is set to 1 for “internally calibrated” devices.

86-87 2 T (Offset) 00 00 T (Offset) is set to zero for “internally calibrated” devices.

88-89 2 V (Slope) 01 00 V (Slope) is set to 1 for “internally calibrated” devices.

90-91 2 V (Offset) 00 00 V (Offset) is set to zero for “internally calibrated” devices.

92-94 3 Reserved 00 00 00 Reserved

95 1 Checksum XX

Byte 95 contains the low order 8 bits of the sum of bytes 0 –

94.

A/D Value (2 Wire Address A2h)

Address # Bytes Name Description

96-97 2 Temperature (MSB, LSB) Internally measured module temperature

98-99 2 Supply Voltage (MSB, LSB) Internally measured supply voltage in module

100-101 2 Tx Bias Current (MSB, LSB) Internally measured Tx Bias current

102-103 2 Tx Optical Power (MSB, LSB) Measured Tx output power

104-105 2 Rx Received Power (MSB, LSB) Measured Rx input power

106-109 4 Reserved

Notes:Temperature (Signed twos complement value)

A2h Byte 96 (Temperature MSB) A2h Byte 97 (Temperature LSB)

S 26 25 24 23 22 21 20 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8

Supply Voltage, Tx Bias Current, Tx Optical Power, Rx Received Power (Unsigned values)

A2h Byte 98 (Vcc MSB) A2h Byte 99 (Vcc LSB)

A2h Byte 100 (TX Bias MSB) A2h Byte 101 (TX Bias LSB)

A2h Byte 102 (TX Power MSB) A2h Byte 103 (TX Power LSB)

A2h Byte 104 (RX Power MSB) A2h Byte 105 (RX Power LSB)

215 2

14 213 212 211 210 29 28 27 26 25 24 23 22 21 20

The digital value conversions are updated every 13ms (nominal) or 20ms (max) in rotation. After getting digital value,

each measurement could be obtained by multiplying digital value by corresponding LSB value:

Temperature = Temp (Digital Value) × LSBTe m p = Temp (Digital Value) × 1

256; when Temperature<128

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

13 Revision: S0

12/20/2007

www.deltaww.com

Temperature = Temp (Digital Value) × LSBTe m p = [Temp (Digital Value) × 1

256]-256; when Temperature≧128

Vcc = Vcc(Digital Value) × LSBVcc=VCC(Digital Value) × 100µV

TX Bias Current = TX Bias Current (Digital Value) × LSBTX,Bias = TX Bias Current (Digital Value) × 2µA

TX Power = TX Power (Digital Value) × LSBTXPower = TX Power (Digital Value) × 0.1µW

RX Power = RX Power (Digital Value) × LSBRXPower = RX Power (Digital Value) × 0.1µW

Optional Status/Control Bits (2 Wire Address A2h)

Address Bit Name Description

110 7 TX Disable State Not implement.

110 6 Soft TX Disable Not implement.

110 5 Reserved

110 4 RX Rate Select State Not implement.

110 3 Soft RX Rate Select Not implement.

110 2 TX Fault State Digital state of the TX Fault Output Pin.

110 1 LOS Digital state of the LOS Output Pin.

110 0 Data_Ready_Bar Indicates transceiver has achieved power up and data is

ready.

111 All Reserved Reserved for SFF-8079

Alarm/Warning Flag Bits (2 Wire Address A2h)

Address Bit Name Description

112 7 Temp High Alarm Set when internal temperature exceeds high alarm level.

112 6 Temp Low Alarm Set when internal temperature is below low alarm level.

112 5 Vcc High Alarm Set when internal supply voltage exceeds high alarm level.

112 4 Vcc Low Alarm Set when internal supply voltage is below low alarm level.

112 3 TX Bias High Alarm Set when TX Bias current exceeds high alarm level.

112 2 TX Bias Low Alarm Set when TX Bias current is below low alarm level.

112 1 TX Power High Alarm Set when TX output power exceeds high alarm level.

112 0 TX Power Low Alarm Set when TX output power is below low alarm level.

113 7 RX Power High Alarm Set when Received Power exceeds high alarm level.

113 6 RX Power Low Alarm Set when Received Power is below low alarm level.

113 5-0 Reserved Alarm

114-115 All Reserved

116 7 Temp High Warning Set when internal temperature exceeds high warning level.

116 6 Temp Low Warning Set when internal temperature is below low warning level.

116 5 Vcc High Warning Set when internal supply voltage exceeds high warning level.

116 4 Vcc Low Warning Set when internal supply voltage is below low warning level.

116 3 TX Bias High Warning Set when TX Bias current exceeds high warning level.

116 2 TX Bias Low Warning Set when TX Bias current is below low warning level.

116 1 TX Power High Warning Set when TX output power exceeds high warning level.

116 0 TX Power Low Warning Set when TX output power is below low warning level.

117 7 RX Power High Warning Set when Received Power exceeds high warning level.

117 6 RX Power Low Warning Set when Received Power is below low warning level.

117 5-0 Reserved Warning

118-119 All Reserved

SPBD-1250F4Q2R

DELTA ELECTRONICS, INC.

14 Revision: S0

12/20/2007

www.deltaww.com

Vendor Specific and User Accessible EEPROM (2 Wire Address A2h)

Address # Bytes Name Description

120-122 3 Reserved

123 1 Password Byte 3 High order byte of 32 bit password

124 1 Password Byte 2 Second highest order byte of 32 bit password

125 1 Password Byte 1 Second lowest order byte of 32 bit password

126 1 Password Byte 0 Low order byte of 32 bit password

127 1 User EEPROM Select “1” selects user writable EEPROM at locations 128-247

128-247 120 User EEPROM User writable EEPROM

248-255 8 Vendor Specific Vendor specific control functions

11. Regulatory Compliance

Feature Test Method Reference Performance

Human Body Model

(HBM)

MIL-STD-883E Method 3015.7

EIA-JESD22-A114

Electrostatic Discharge

(ESD) to the Electrical

Pins Machine Model (MM) EIA-JESD22-A115

Contact Discharge IEC/EN 61000-4-2 Electrostatic Discharge

(ESD) to the Simplex

Receptacle Air Discharge IEC/EN 61000-4-2

Radio Frequency

Electromagnetic Field

Immunity

IEC/EN 61000-4-3

Electromagnetic

Interference (EMI)

FCC Part 15 Class B

EN 55022 Class B

(CISPR 22A)

(1) Satisfied with

electrical

characteristics of

product spec.

(2) No physical damage

Laser Eye Safety

FDA/CDRH

TUV

FDA 21CFR 1040.10, 1040.11

IEC/EN 60825-1

IEC/EN 60825-2

CDRH File # 0420993

TUV Certificate #

R50032471

Component Recognition

TUV

UL/CSA

IEC/EN 60950

UL 60950

UL File # E239394

Appendix A. Document Revision

Version No. Date Description

S0 2007-12-20 Preliminary datasheet