DEMOBOARD PROFET - Infineon Technologies

Never stop thinking.

Automotive Power

Getting Started, V 2.0, April 2004

PROFET Demo Kit

BTS 5241L

BTS 5234G

BTS 5230GS

BTS 6143D

Getting Started

PROFET Demo Kit

Getting Started 2 V 2.0, 2004-04

Preface

The PROFET Demo Kit is a versatile tool to demonstrate the functions of the

BTS 5241L, BTS 5234G, BTS 5230GS and BTS 6143D. It is an ideal tool to become

familiar with the performance of the devices.

The PROFET Demo Kit consists of five different boards devided in two types. The

PROFET are mounted on the power boards which also contain 4 mm plug sockets for

power supply and loads. The power boards are connected via a D-SUB-15 connector to

the control board. The complete PROFET Demo Kit is reverse polarity protected.

There are four different power boards available. The P-DSO-12 board contains

BTS 5241L, a dual channel PROFET in P-DSO-12 power package. The P-DSO-20

board is equipped with BTS 5234G, a dual channel PROFET in P-DSO-20 package.

Two BTS 5230GS dual channel PROFET in P-DSO-14 package are mounted on the P-

DSO-14 board. Two BTS 6143D high current PROFET are available on the Power HIC

board.

Getting Started

PROFET Demo Kit

Getting Started

Getting Started 3 V 2.0, 2004-04

1 Getting Started

This chapter is intended to describe a step by step procedure to get the system running

the first time. For detailed information about the hardware and software of the

PROFET Demo Kit, please refer to the “Tool Description” document.

1.1 Usage of Hardware

The hardware is intended to be used the following way:

1. select one of the power boards

2. connect the control board

3. connect 12 V bulbs to the OUTx plugs of the power boards according to following

table:

4. connect a 12 V power supply, which is able to drive the loads’ current, to the VBB and

GND plug of the power board. The control board is supplied via the power board.

5. check, if the jumper at the control board is placed in position “normal”

6. occasionally, the reset button has to be pressed to start-up the system after power up

7. use switches to switch on the loads

To see the performance and protection features of the device, following evaluation could

be performed:

• Open Load: Remove the load of one channel completely

The open load LED of that channel will be switched on.

• Low load: Reduce the load of one channel (e.g. P-DSO-12: Remove one 21 W bulb)

The open load LED is enabled, when that channel is switched on.

• Short Circuit to GND: Short Circuit one channel

The over temperature LED is enabled, when that channel is switched on.

•Reverse Polarity:

1) Connect the power supply in reverse polarity.

All loads will be switched on

Note: Please keep in mind that short circuit evaluation as well as normal power

dissipation will heat up the power devices. Harmful temperatures can be

reached at the device packages and the PCB!

Power Board Chanel 1 Channel 2 Channel 3 Channel 4

P-DSO-12 21 W + 21 W +

21 W + 21 W +

- -

P-DSO-20 21 W 21 W - -

P-DSO-14 10 W 10 W 10 W 10 W

Power HIC 55 W 60 W - -

1) the control board is reverse polarity protected

Edition 2004-04

Published by Infineon Technologies AG,

St.-Martin-Strasse 53,

81669 München, Germany

Attention please!

The information herein is given to describe certain components and shall not be considered as warranted

characteristics.

Terms of delivery and rights to technical change reserved.

We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding

circuits, descriptions and charts stated herein.

Infineon Technologies is an approved CECC manufacturer.

Information

For further information on technology, delivery terms and conditions and prices please contact your nearest

Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide

(www.infineon.com).

Warnings

Due to technical requirements components may contain dangerous substances. For information on the types in

question please contact your nearest Infineon Technologies Office.

Infineon Technologies Components may only be used in life-support devices or systems with the express written

approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure

of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support

devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain

and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may

be endangered.

Qualität hat für uns eine umfassende

Bedeutung. Wir wollen allen Ihren

Ansprüchen in der bestmöglichen

Weise gerecht werden. Es geht uns also

nicht nur um die Produktqualität –

unsere Anstrengungen gelten

gleichermaßen der Lieferqualität und

Logistik, dem Service und Support

sowie allen sonstigen Beratungs- und

Betreuungsleistungen.

Dazu gehört eine bestimmte

Geisteshaltung unserer Mitarbeiter.

Total Quality im Denken und Handeln

gegenüber Kollegen, Lieferanten und

Ihnen, unserem Kunden. Unsere

Leitlinie ist jede Aufgabe mit „Null

Fehlern“ zu lösen – in offener

Sichtweise auch über den eigenen

Arbeitsplatz hinaus – und uns ständig

zu verbessern.

Unternehmensweit orientieren wir uns

dabei auch an „top“ (Time Optimized

Processes), um Ihnen durch größere

Schnelligkeit den entscheidenden

Wettbewerbsvorsprung zu verschaffen.

Geben Sie uns die Chance, hohe

Leistung durch umfassende Qualität zu

beweisen.

Wir werden Sie überzeugen.

Quality takes on an allencompassing

significance at Semiconductor Group.

For us it means living up to each and

every one of your demands in the best

possible way. So we are not only

concerned with product quality. We

direct our efforts equally at quality of

supply and logistics, service and

support, as well as all the other ways in

which we advise and attend to you.

Part of this is the very special attitude of

our staff. Total Quality in thought and

deed, towards co-workers, suppliers

and you, our customer. Our guideline is

“do everything with zero defects”, in an

open manner that is demonstrated

beyond your immediate workplace, and

to constantly improve.

Throughout the corporation we also

think in terms of Time Optimized

Processes (top), greater speed on our

part to give you that decisive

competitive edge.

Give us the chance to prove the best of

performance through the best of quality

– you will be convinced.

http://www.infineon.com

Total Quality Management

Published by Infineon Technologies AG