ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 ADC14V155 14-Bit, 155 MSPS, 1.1 GHz Bandwidth A/D Converter with LVDS Outputs Check for Samples: ADC14V155 FEATURES DESCRIPTION * * * * * * * * * The ADC14V155 is a high-performance CMOS analog-to-digital converter with LVDS outputs. It is capable of converting analog input signals into 14-Bit digital words at rates up to 155 Mega Samples Per Second (MSPS). Data leaves the chip in a DDR (Dual Data rate) format; this allows both edges of the output clock to be utilized while achieving a smaller package size. This converter uses a differential, pipelined architecture with digital error correction and an onchip sample-and-hold circuit to minimize power consumption and the external component count, while providing excellent dynamic performance. A unique sample-and-hold stage yields a full-power bandwidth of 1.1 GHz. The ADC14V155 operates from dual +3.3V and +1.8V power supplies and consumes 951 mW of power at 155 MSPS. 1 2 * * * 1.1 GHz Full Power Bandwidth Internal Sample-and-Hold Circuit Low Power Consumption Internal Precision 1.0V Reference Single-Ended or Differential Clock Modes Clock Duty Cycle Stabilizer Dual +3.3V and +1.8V Supply Operation Power-Down and Sleep Modes Offset Binary or 2's Complement Output Data Format Dual Data Rate (DDR) LVDS Outputs Pin-Compatible: ADC12V170 48-Pin WQFN Package, (7x7x0.8mm, 0.5mm Pin-Pitch) APPLICATIONS * * * * * * * High IF Sampling Receivers Wireless Base Station Receivers Power Amplifier Linearization Multi-Carrier, Multi-Mode Receivers Test and Measurement Equipment Communications Instrumentation Radar Systems KEY SPECIFICATIONS * * * * * * * Resolution 14 Bits Conversion Rate 155 MSPS SNR (fIN = 70 MHz) 71.7 dBFS (typ) SFDR (fIN = 70 MHz) 86.9 dBFS (typ) ENOB (fIN = 70 MHz) 11.5 bits (typ) Full Power Bandwidth 1.1 GHz (typ) Power Consumption 951 mW (typ) The separate +1.8V supply for the digital output interface allows lower power operation with reduced noise. A power-down feature reduces the power consumption to 15 mW while still allowing fast wakeup time to full operation. In addition there is a sleep feature which consumes 50 mW of power and has a faster wake-up time. The differential inputs provide a full scale differential input swing equal to 2 times the reference voltage. A stable 1.0V internal voltage reference is provided, or the ADC14V155 can be operated with an external reference. Clock mode (differential versus single-ended) and output data format (offset binary versus 2's complement) are pin-selectable. A duty cycle stabilizer maintains performance over a wide range of input clock duty cycles. The ADC14V155 is pin-compatible with the ADC12V170. It is available in a 48-lead WQFN package and operates over the industrial temperature range of -40C to +85C. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2013, Texas Instruments Incorporated ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Block Diagram INTERNAL REFERENCE VREF VRP VRM VRN 7 VIN+ VIN- 14BIT HIGH SPEED PIPELINE ADC SHA DIGITAL CORRECTION 7 LVDS Output Driver CLK+ CLK- D0+ to D13+ D0- to D13OVR+ OVRDRDY+ CLOCK/DUTY CYCLE STABILIZER DRDY- AGND VA 37 VA VA AGND VRP VRN AGND 38 39 40 41 42 43 VREF VRM 44 45 6 31 ADC14V155 (Top View) 7 8 30 29 9 28 10 27 11 26 Submit Documentation Feedback D7-/D6- DRGND DRDY+ DRDYD13+/D12+ D13-/D12D11+/D10+ D11-/D10D9+/D8+ D9-/D8DRGND VDR 24 25 VDR D7+/D6+ 23 22 D5+/D4+ 21 D5-/D4- 20 D3+/D2+ 19 D3-/D2- D1+/D0+ 12 18 * Exposed pad must be soldered to ground plane to ensure rated performance. VD 2 AGND 32 13 CLK- 5 17 CLK+ 33 D1-/D0- AGND 4 16 VA 34 OVR- CLK_SEL/DF 3 OVR+ VA PD/Sleep 35 15 VIN+ AGND 36 2 DGND VIN- 46 48 AGND 1 14 VA 47 VA Connection Diagram Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit Description ANALOG I/O 3 VIN- VA 4 VIN+ 43 VRP 45 VRM Differential analog input pins. The differential full-scale input signal level is two times the reference voltage with each input pin signal centered on a common mode voltage, VCM. AGND VA VRM VA VRN VREF 44 VRN VA These pins should each be bypassed to AGND with a low ESL (equivalent series inductance) 0.1 F capacitor placed very close to the pin to minimize stray inductance. A 0.1 F capacitor should be placed between VRP and VRN as close to the pins as possible, and a 10 F capacitor should be placed in parallel. VRP and VRN should not be loaded. VRM may be loaded to 1mA for use as a temperature stable 1.5V reference. It is recommended to use VRM to provide the common mode voltage, VCM, for the differential analog inputs, VIN+ and VIN-. VRP AGND VA IDC 46 VREF AGND 8 CLK_SEL/DF This is a four-state pin controlling the input clock mode and output data format. CLK_SEL/DF = VA, CLK+ and CLK- are configured as a differential clock input. The output data format is 2's complement. CLK_SEL/DF = (2/3)*VA, CLK+ and CLK- are configured as a differential clock input. The output data format is offset binary. CLK_SEL/DF = (1/3)*VA, CLK+ is configured as a single-ended clock input and CLK- should be tied to AGND. The output data format is 2's complement. CLK_SEL/DF = AGND, CLK+ is configured as a single-ended clock input and CLK- should be tied to AGND. The output data format is offset binary. VA AGND 7 PD/Sleep This pin can be used as either the +1.0V internal reference voltage output (internal reference operation) or as the external reference voltage input (external reference operation). To use the internal reference, VREF should be decoupled to AGND with a 0.1 F, low equivalent series inductance (ESL) capacitor. In this mode, VREF defaults as the output for the internal 1.0V reference. To use an external reference, overdrive this pin with a low noise external reference voltage. The input impedance looking into this pin is 9k. Therefore, to overdrive this pin, the output impedance of the external reference source should be << 9k. This pin should not be used to source or sink current. The full scale differential input voltage range is 2 * VREF. This is a three-state input controlling Power Down and Sleep modes. PD = VA, Power Down is enabled. In the Power Down state only the reference voltage circuitry remains active and power dissipation is reduced. PD = VA/2, Sleep mode is enabled. Sleep mode is similar to Power Down mode - it consumes more power but has a faster recovery time. PD = AGND, Normal operation. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 3 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 Pin No. Symbol 11 CLK+ www.ti.com Equivalent Circuit Description VA 12 The clock input pins can be configured to accept either a singleended or a differential clock input signal. When the single-ended clock mode is selected through CLK_SEL/DF (pin 8), connect the clock input signal to the CLK+ pin and connect the CLK- pin to AGND. When the differential clock mode is selected through CLK_SEL/DF (pin 8), connect the positive and negative clock inputs to the CLK+ and CLK- pins, respectively. The analog input is sampled on the falling edge of the clock input. CLK- AGND DIGITAL I/O 17 18 19 20 21 22 23 24 27 28 29 30 31 32 D1-/D0D1+/D0+ D3-/D2D3+/D2+ D5-/D4D5+/D4+ D7-/D6D7+/D6+ D9-/D8D9+/D8+ D11-/D10D11+/D10+ D13-/D12D13+/D12+ 15 16 OVROVR+ LVDS digital data output pins that make up the 14-Bit conversion result. The data is provided in a 2:1 multiplexed manner synchronous to DRDY+/-. The even bits should be captured with the rising edge of DRDY and the odd bits should be captured with the falling edge of DRDY. D0 is the LSB. D13 is the MSB. VDR - + + + - Over-Range Indicator. This LVDS output is set HIGH when the input amplitude goes outside the expected 14-Bit conversion range (0 to 16383). DRDY+ DRDY- Data Ready Strobe. This LVDS output is used to clock the output data. It has the same frequency as the sampling clock. One half of the data word is output with each edge of this signal - thus transferring a complete 14-bit word in each cycle of this clock. The even bits should be captured with the rising edge of DRDY and the odd bits should be captured with the falling edge of DRDY. 1, 6, 9, 37, 40, 41, 48 VA Positive analog supply pins. These pins should be connected to a quiet +3.3V source and be bypassed to AGND with 0.01 F and 0.1 F capacitors located close to the power pins. 2, 5, 10, 38, 39, 42, 47, Exposed Pad AGND DRGND 33 34 ANALOG POWER The ground return for the analog supply. Note: Exposed pad on bottom of package must be soldered to ground plane to ensure rated performance. DIGITAL POWER 4 13 VD 14 DGND 25, 36 VDR 26, 35 DRGND Positive digital supply pin. This pin should be connected to a quiet +3.3V source and be bypassed to DGND with a 0.01 F and 0.1 F capacitor located close to the power pin. The ground return for the digital supply. Positive driver supply pin for the output drivers. This pin should be connected to a quiet voltage source of +1.8V and be bypassed to DRGND with 0.01 F and 0.1 F capacitors located close to the power pins. The ground return for the digital output driver supply. These pins should be connected to the system digital ground, but not be connected in close proximity to the ADC's DGND or AGND pins. See LAYOUT AND GROUNDING for more details. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) -0.3V to 4.2V Supply Voltage (VA, VD) -0.3V to 2.35V Supply Voltage (VDR) 100 mV |VA-VD| -0.3V to (VA +0.3V) Voltage on Any Input Pin (Not to exceed 4.2V) Voltage on Any Output Pin (Not to exceed 2.35V) -0.3V to (VDR +0.2V) Input Current at Any Pin other than Supply Pins (4) 5 mA Package Input Current (4) 50 mA Max Junction Temp (TJ) +150C Thermal Resistance (JA) 24C/W Package Dissipation at TA = 25C (5) 5.2W Human Body Model (6) ESD Rating 2000 V Machine Model (6) 200 V Charge Device Model 1000 V -65C to +150C Storage Temperature Soldering process must comply with TI's Reflow Temperature Profile specifications. Refer to www.ti.com/packaging. (1) (2) (3) (4) (5) (6) (7) (7) All voltages are measured with respect to GND = AGND = DGND = DRGND = 0V, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is specified to be functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be limited to 5 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5 mA to 10. The maximum allowable power dissipation is dictated by TJ,max, the junction-to-ambient thermal resistance, (JA), and the ambient temperature, (TA), and can be calculated using the formula PD,max = (TJ,max - TA )/JA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Such conditions should always be avoided. Human Body Model is 100 pF discharged through a 1.5 k resistor. Machine Model is 220 pF discharged through 0 Reflow temperature profiles are different for lead-free and non-lead-free packages. Operating Ratings (1) (2) Operating Temperature -40C TA +85C Supply Voltage (VA, VD) +3.0V to +3.6V Output Driver Supply (VDR) +1.6V to +2.0V -0.05V to (VA + 0.05V) CLK Clock Duty Cycle 30/70 % Analog Input Pins 0V to 2.6V VCM 1.4V to 1.6V 100mV |AGND-DGND| (1) (2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is specified to be functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. All voltages are measured with respect to GND = AGND = DGND = DRGND = 0V, unless otherwise specified. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 5 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (1) (2) (3) Symbol Parameter Conditions Typical (4 ) Limits Units (Limits) 14 Bits (min) 5.0 LSB (max) STATIC CONVERTER CHARACTERISTICS Resolution with No Missing Codes INL Integral Non Linearity DNL (5) Differential Non Linearity PGE Full Scale Input 2.40 Full Scale Input 0.55 Positive Gain Error NGE Negative Gain Error TC GE Gain Error Tempco VOFF Offset Error (VIN+ = VIN-) TC VOFF Offset Error Tempco +0.06 -0.06 -40C TA +85C -5.0 LSB (min) 1.1 LSB (max) -1.0 LSB (min) 3.20 %FS (max) -3.20 %FS (min) 2.85 %FS (max) -2.85 %FS (min) 0.85 %FS (max) -0.85 %FS (min) +8.0 -0.03 -40C TA +85C ppm/C +0.5 ppm/C Under Range Output Code 0 0 Over Range Output Code 16383 16383 REFERENCE AND ANALOG INPUT CHARACTERISTICS VCM Common Mode Input Voltage VRM Reference Ladder Midpoint Output Voltage Output load = 1 mA CIN VIN Input Capacitance (each pin to GND) (6) VIN = 1.5 Vdc 0.5 V VREF Reference Voltage 1.5 V 1.5 V (CLK LOW) 6 pF (CLK HIGH) 9 pF (7) Reference Input Resistance (1) 1.00 V 9 k The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. VA I/O To Internal Circuitry AGND (2) (3) (4) (5) (6) (7) 6 To ensure accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. With the test condition for VREF = +1.0V (2VP-P differential input), the 14-Bit LSB is 122.1 V. Typical figures are at TA = 25C and represent most likely parametric norms at the time of product characterization. The typical specifications are not ensured. Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive and negative full-scale. The input capacitance is the sum of the package/pin capacitance and the sample and hold circuit capacitance. Optimum performance will be obtained by keeping the reference input in the 0.9V to 1.1V range. The LM4051CIM3-ADJ (SOT-23 package) is recommended for external reference applications. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Dynamic Converter Electrical Characteristics Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (1) (2) (3) Symbol Parameter Conditions Typical (4) Limits Units (Limits) DYNAMIC CONVERTER CHARACTERISTICS, AIN= -1dBFS FPBW SNR SFDR ENOB THD H2 Signal-to-Noise Ratio Spurious Free Dynamic Range Effective Number of Bits Total Harmonic Disortion Second Harmonic Distortion H3 (1) Full Power Bandwidth Third Harmonic Distortion -1 dBFS Input, -3 dB Corner 1.1 fIN = 10 MHz 71.9 fIN = 70 MHz 71.7 fIN = 169 MHz 70.0 dBFS fIN = 238 MHz 69.5 dBFS fIN = 400 MHz 67.7 dBFS fIN = 10 MHz 84.6 fIN = 70 MHz 86.9 fIN = 169 MHz 84.5 dBFS fIN = 238 MHz 85.0 dBFS fIN = 400 MHz 75.0 dBFS fIN = 10 MHz 11.54 fIN = 70 MHz 11.5 fIN = 169 MHz 11.3 Bits fIN = 238 MHz 11.2 Bits fIN = 400 MHz 10.8 Bits fIN = 10 MHz -79.9 dBFS fIN = 70 MHz -82.2 fIN = 169 MHz -80.8 dBFS fIN = 238 MHz -81.9 dBFS fIN = 400 MHz -73.0 dBFS GHz dBFS 68.6 dBFS dBFS 74.0 dBFS Bits 10.9 -72.0 Bits dBFS fIN = 10 MHz -95.2 fIN = 70 MHz -94.3 dBFS fIN = 169 MHz -85.9 dBFS fIN = 238 MHz -85.0 dBFS fIN = 400 MHz -75.0 dBFS fIN = 10 MHz -84.6 fIN = 70 MHz -86.9 fIN = 169 MHz -84.5 dBFS fIN = 238 MHz -97.1 dBFS fIN = 400 MHz -79.2 dBFS -77.0 dBFS dBFS -74.0 dBFS The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. VA I/O To Internal Circuitry AGND (2) (3) (4) To ensure accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. With the test condition for VREF = +1.0V (2VP-P differential input), the 14-Bit LSB is 122.1 V. Typical figures are at TA = 25C and represent most likely parametric norms at the time of product characterization. The typical specifications are not ensured. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 7 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Dynamic Converter Electrical Characteristics (continued) Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C(1)(2)(3) Symbol SINAD Parameter Conditions Signal-to-Noise and Distortion Ratio Typical (4) Limits Units (Limits) fIN = 10 MHz 71.4 fIN = 70 MHz 71.2 dBFS fIN = 169 MHz 69.6 dBFS fIN = 238 MHz 69.2 dBFS fIN = 400 MHz 66.6 dBFS 67.7 dBFS Logic and Power Supply Electrical Characteristics Unless otherwise specified, the following specifications apply: VIN = -1 dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (1) (2) (3) Symbol Parameter Conditions Typical (4) Limits Units (Limits) CLK INPUT CHARACTERISTICS VIN(1) Logical "1" Input Voltage VD = 3.6V 2.0 V (min) VIN(0) Logical "0" Input Voltage VD = 3.0V 0.8 V (max) IIN(1) Logical "1" Input Current VIN = 3.3V 10 A IIN(0) Logical "0" Input Current VIN = 0V -10 A CIN Input Capacitance 5 pF DIGITAL OUTPUT CHARACTERISTICS (D0+/- to D13+/-, DRDY+/-, OVR+/-) VOD LVDS differential output voltage See (5) VOS The common-mode voltage of the LVDS output See (5) RL Intended Load Resistance 350 1.22 250 mVP-P (min) 450 mVP-P (max) 1.125 V (min) 1.375 V (max) 100 POWER SUPPLY CHARACTERISTICS IA Analog Supply Current Full Operation 273 341 mA (max) ID Digital Supply Current Full Operation 15 17.1 mA (max) IDR Digital Output Supply Current Full Operation 31.5 Power Consumption Excludes IDR 951 1181 mW (max) (1) mA Power Down Power Consumption 15 mW Sleep Power Consumption 50 mW The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. VA I/O To Internal Circuitry AGND (2) (3) (4) (5) 8 To ensure accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. With the test condition for VREF = +1.0V (2VP-P differential input), the 14-Bit LSB is 122.1 V. Typical figures are at TA = 25C and represent most likely parametric norms at the time of product characterization. The typical specifications are not ensured. This test parameter is specified by design and characterization. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Timing and AC Characteristics Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 170 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN TA TMAX. All other limits apply for TA = 25C (1) (2) (3) Limits Units (Limits) Maximum Clock Frequency 155 MHz (max) Minimum Clock Frequency 5 MHz (min) Symbol Parameter Conditions Typical Clock High Time 3.0 Clock Low Time 3.0 Conversion Latency tOD (4) ns ns 8.5 Clock Cycles Output Delay of CLK to DATA Relative to falling edge of CLK 4.0 tDV Data Output Valid Time Time output data is valid before the output edge of DRDY (5) 1.3 0.9 ns (min) tDNV Data Output Not Valid Time Time till output data is not valid after the output edge of DRDY (5) 1.3 0.9 ns (min) tAD Aperture Delay 0.5 ns Aperture Jitter 0.08 ps rms (1) ns Power Down Recovery Time 0.1 F on pins 43, 44; 10 F and 0.1 F between pins 43, 44; 0.1 F and 10 F on pins 45, 46 3.0 ms Sleep Recovery Time 0.1 F on pins 43, 44; 10 F and 0.1 F between pins 43, 44; 0.1 F and 10 F on pins 45, 46 100 s The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. VA I/O To Internal Circuitry AGND (2) (3) (4) (5) To ensure accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. With the test condition for VREF = +1.0V (2VP-P differential input), the 14-Bit LSB is 122.1 V. Typical figures are at TA = 25C and represent most likely parametric norms at the time of product characterization. The typical specifications are not ensured. This test parameter is specified by design and characterization. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 9 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Specification Definitions APERTURE DELAY is the time after the falling edge of the clock to when the input signal is acquired or held for conversion. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the total time of one period. The specification here refers to the ADC clock input signal. COMMON MODE VOLTAGE (VCM) is the common DC voltage applied to both input terminals of the ADC. CONVERSION LATENCY is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as: Gain Error = Positive Full Scale Error - Negative Full Scale Error (1) It can also be expressed as Positive Gain Error and Negative Gain Error, which are calculated as: PGE = Positive Full Scale Error - Offset Error NGE = Offset Error - Negative Full Scale Error (2) INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1/2 LSB below the first code transition) through positive full scale (1/2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS. LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS/2n, where "VFS" is the full scale input voltage and "n" is the ADC resolution in bits. LVDS DIFFERENTIAL OUTPUT VOLTAGE (VOD) is the absolute value of the differnece between VDX+ and VDXoutputs; each measured with respect to Ground. LVDS OUTPUT OFFSET VOLTAGE (VOS) is the midpoint between the DX+ and DX- pins' output voltages; i.e., [VDx+ + VDX-]/2. MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC14V155 is ensured not to have any missing codes. MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale. NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of 1/2 LSB above negative full scale. OFFSET ERROR is the difference between the two input voltages [(VIN+) - (VIN-)] required to cause a transition from code 8191 to 8192. OUTPUT DELAY is the time delay after the falling edge of the clock before the data update is presented at the output pins. PIPELINE DELAY (LATENCY) See CONVERSION LATENCY. POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of 11/2 LSB below positive full scale. 10 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. PSRR is the ratio of the Full-Scale output of the ADC with the supply at the minimum DC supply limit to the Full-Scale output of the ADC with the supply at the maximum DC supply limit, expressed in dB. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or DC. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first nine harmonic levels at the output to the level of the fundamental at the output. THD is calculated as (3) where f1 is the RMS power of the fundamental (output) frequency and f2 through f10 are the RMS power of the first 9 harmonic frequencies in the output spectrum. SECOND HARMONIC DISTORTION (2ND HARM) is the difference expressed in dB, between the RMS power in the input frequency at the output and the power in its 2nd harmonic level at the output. THIRD HARMONIC DISTORTION (3RD HARM) is the difference, expressed in dB, between the RMS power in the input frequency at the output and the power in its 3rd harmonic level at the output. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 11 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Timing Diagram N+9.5 N+8.5 N+10.5 Sample N+9 Sample N+10 Sample N Vin tAD ttpp CLK+ CLKLatency tOD tp DRDY+ DRDYtDV tDNV tDV odd bits* Dx+/Word N-1 tDNV even bits* Word N Word N+1 OVR+/(High if output code exceeds OE[* OE vP ) * Even Bits: D0 (LSB), D2, D4, D6, D8, D10, D12 Odd Bits: D1, D3, D5, D7, D9, D11, D13 (MSB) Figure 1. Output Timing 12 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Transfer Characteristic Figure 2. Transfer Characteristic (Offset Binary Format) Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 13 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics, DNL, INL Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. (1) (2) (3) (1) DNL INL Figure 3. Figure 4. The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above 2.6V or below GND as described in the Operating Ratings section. VA I/O To Internal Circuitry AGND (2) (3) 14 To ensure accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. With the test condition for VREF = +1.0V (2VP-P differential input), the 14-Bit LSB is 122.1 V. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Typical Performance Characteristics, Dynamic Performance Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, fIN = 70 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. SNR, SINAD, SFDR vs. fIN DISTORTION vs. fIN Figure 5. Figure 6. SNR, SINAD, SFDR vs. VA DISTORTION vs. VA Figure 7. Figure 8. SNR, SINAD, SFDR vs. VDR DISTORTION vs. VDR Figure 9. Figure 10. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 15 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics, Dynamic Performance Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, fIN = 70 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. 16 SNR, SINAD, SFDR vs. VREF DISTORTION vs. VREF Figure 11. Figure 12. SNR, SINAD, SFDR vs. Temperature DISTORTION vs. Temperature Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Typical Performance Characteristics, Dynamic Performance Unless otherwise specified, the following specifications apply: VIN = -1dBFS, AGND = DGND = DRGND = 0V, VA = VD = +3.3V, VDR = +1.8V, Internal VREF = +1.0V, fCLK = 155 MHz, fIN = 70 MHz, VCM = VRM, CL = 5 pF/pin, Single-Ended Clock Mode, Offset Binary Format. Typical values are for TA = 25C. Spectral Response @ 70 MHz Input Spectral Response @ 169 MHz Input Figure 15. Figure 16. Spectral Response @ 238 MHz Input Spectral Response @ 350 MHz Input Figure 17. Figure 18. Spectral Response @ 400 MHz Input Figure 19. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 17 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com FUNCTIONAL DESCRIPTION Operating on dual +3.3V and +1.8V supplies, the ADC14V155 digitizes a differential analog input signal to 14 bits, using a differential pipelined architecture with error correction circuitry and an on-chip sample-and-hold circuit to ensure maximum performance. The user has the choice of using an internal 1.0V stable reference, or using an external reference. The ADC14V155 will accept an external reference between 0.9V and 1.1V (1.0V recommended) which is buffered onchip to ease the task of driving that pin. The +1.8V output driver supply reduces power consumption and decreases the noise at the output of the converter. The quad state function pin CLK_SEL/DF (pin 8) allows the user to choose between using a single-ended or a differential clock input and between offset binary or 2's complement output data format. The digital outputs are LVDS compatible signals that are clocked by a synchronous data ready output signal (DRDY pins 33, 34) at the same rate as the clock input. For the ADC14V155 the clock frequency can be between 5 MSPS and 155 MSPS (typical) with fully specified performance at 155 MSPS. The analog input is acquired at the falling edge of the clock and the digital data for a given sample is output on the falling edge of the DRDY signal and is delayed by the pipeline for 8.5 clock cycles. The data should be captured on the rising edge of the DRDY signal. Power-down is selectable using the PD/Sleep pin (pin 7). A logic high on the PD/Sleep pin disables everything except the voltage reference circuitry and reduces the converter power consumption to 15 mW. When PD/Sleep is biased to VA/2 the the chip enters sleep mode. In sleep mode everything except the voltage reference circuitry and its accompanying on chip buffer is disabled; power consumption is reduced to 50 mW. For normal operation, the PD/Sleep pin should be connected to the analog ground (AGND). A duty cycle stabilizer maintains performance over a wide range of clock duty cycles. APPLICATIONS INFORMATION OPERATING CONDITIONS We recommend that the following conditions be observed for operation of the ADC14V155: 3.0V VA 3.6V VD = VA VDR = 1.8V 5 MHz fCLK 155 MHz 1.0V internal reference 0.9V VREF 1.1V (for an external reference) VCM = 1.5V (from VRM) Single Ended Clock Mode ANALOG INPUTS Signal Inputs Differential Analog Input Pins The ADC14V155 has one pair of analog signal input pins, VIN+ and VIN-, which form a differential input pair. The input signal, VIN, is defined as VIN = (VIN+) - (VIN-) (4) Figure 20 shows the expected input signal range. Note that the common mode input voltage, VCM, should be 1.5V. Using VRM (pin 45) for VCM will ensure the proper input common mode level for the analog input signal. The peaks of the individual input signals should each never exceed 2.6V. Each analog input pin of the differential pair should have a peak-to-peak voltage equal to the reference voltage, VREF, be 180 out of phase with each other and be centered around VCM.The peak-to-peak voltage swing at each analog input pin should not exceed the value of the reference voltage or the output data will be clipped. 18 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Figure 20. Expected Input Signal Range For single frequency sine waves the full scale error in LSB can be described as approximately EFS = 16384 ( 1 - sin (90 + dev)) (5) Where dev is the angular difference in degrees between the two signals having a 180 relative phase relationship to each other (see Figure 21). For single frequency inputs, angular errors result in a reduction of the effective full scale input. For complex waveforms, however, angular errors will result in distortion. Figure 21. Angular Errors Between the Two Input Signals Will Reduce the Output Level or Cause Distortion It is recommended to drive the analog inputs with a source impedance less than 100. Matching the source impedance for the differential inputs will improve even ordered harmonic performance (particularly second harmonic). Table 1 indicates the input to output relationship of the ADC14V155. Table 1. Input to Output Relationship VIN+ VIN- Binary Output 2's Complement Output VCM - VREF/2 VCM + VREF/2 00 0000 0000 0000 10 0000 0000 0000 VCM - VREF/4 VCM + VREF/4 01 0000 0000 0000 11 0000 0000 0000 VCM VCM 10 0000 0000 0000 00 0000 0000 0000 VCM + VREF/4 VCM - VREF/4 11 0000 0000 0000 01 0000 0000 0000 VCM + VREF/2 VCM - VREF/2 11 1111 1111 1111 01 1111 1111 1111 Negative Full-Scale Mid-Scale Positive Full-Scale Driving the Analog Inputs The VIN+ and the VIN- inputs of the ADC14V155 have an internal sample-and-hold circuit which consists of an analog switch followed by a switched-capacitor amplifier. The analog inputs are connected to the sampling capacitors through NMOS switches, and each analog input has parasitic capacitances associated with it. When the clock is high, the converter is in the sample phase. The analog inputs are connected to the sampling capacitor through the NMOS switches, which causes the capacitance at the analog input pins to appear as the pin capacitance plus the internal sample and hold circuit capacitance (approximately 9 pF). While the clock level remains high, the sampling capacitor will track the changing analog input voltage. When the clock transitions from high to low, the converter enters the hold phase, during which the analog inputs are disconnected from the sampling capacitor. The last voltage that appeared at the analog input before the clock transition will be held on the sampling capacitor and will be sent to the ADC core. The capacitance seen at the analog input during the hold phase appears as the sum of the pin capacitance and the parasitic capacitances associated with the sample and hold circuit of each analog input (approximately 6 pF). Once the clock signal transitions from low to high, the analog inputs will be reconnected to the sampling capacitor to capture the next sample. Usually, there will be a difference between the held voltage on the sampling capacitor and the new voltage at the analog input. This will cause a charging glitch that is proportional to the voltage difference between the two samples to appear at the analog input pin. The input circuitry must be fast enough to allow the sampling capacitor to settle before the clock signal goes low again, as incomplete settling can degrade the SFDR performance. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 19 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com A single-ended to differential conversion circuit is shown in Figure 22. A transformer is preferred for high frequency input signals. Terminating the transformer on the secondary side provides two advantages. First, it presents a real broadband impedance to the ADC inputs and second, it provides a common path for the charging glitches from each side of the differential sample-and-hold circuit. One short-coming of using a transformer to achieve the single-ended to differential conversion is that most RF transformers have poor low frequency performance. A differential amplifier can be used to drive the analog inputs for low frequency applications. The amplifier must be fast enough to settle from the charging glitches on the analog input resulting from the sample-and-hold operation before the clock goes high and the sample is passed to the ADC core. The SFDR performance of the converter depends on the external signal conditioning circuity used, as this affects how quickly the sample-and-hold charging glitch will settle. An external resistor and capacitor network as shown in Figure 22 should be used to isolate the charging glitches at the ADC input from the external driving circuit and to filter the wideband noise at the converter input. These components should be placed close to the ADC inputs because the analog input of the ADC is the most sensitive part of the system, and this is the last opportunity to filter that input. For Nyquist applications the RC pole should be at the ADC sample rate. The ADC input capacitance in the sample mode should be considered when setting the RC pole. For wideband undersampling applications, the RC pole should be set at about 1.5 to 2 times the maximum input frequency to maintain a linear delay response. Input Common Mode Voltage The input common mode voltage, VCM, should be in the range of 1.4V to 1.6V and be a value such that the peak excursions of the analog signal do not go more negative than ground or more positive than 2.6V. It is recommended to use VRM (pin 45) as the input common mode voltage. Reference Pins The ADC14V155 is designed to operate with an internal 1.0V reference, or an external 1.0V reference, but performs well with external reference voltages in the range of 0.9V to 1.1V. The internal 1.0 Volt reference is the default condition when no external reference input is applied to the VREF pin. If a voltage in the range of 0.9V to 1.1V is applied to the VREF pin, then that voltage is used for the reference. The VREF pin should always be bypassed to ground with a 0.1 F capacitor close to the reference input pin. Lower reference voltages will decrease the signal-to-noise ratio (SNR) of the ADC14V155. Increasing the reference voltage (and the input signal swing) beyond 1.1V may degrade THD for a full-scale input, especially at higher input frequencies. It is important that all grounds associated with the reference voltage and the analog input signal make connection to the ground plane at a single, quiet point to minimize the effects of noise currents in the ground path. The Reference Bypass Pins (VRP, VRM, and VRN) are made available for bypass purposes. All these pins should each be bypassed to ground with a 0.1 F capacitor. A 0.1 F and a 10 F capacitor should be placed between the VRP and VRN pins, as shown in Figure 22. This configuration is necessary to avoid reference oscillation, which could result in reduced SFDR and/or SNR. VRM may be loaded to 1mA for use as a temperature stable 1.5V reference. The remaining pins should not be loaded. Smaller capacitor values than those specified will allow faster recovery from the power down and sleep modes, but may result in degraded noise performance. Loading any of these pins, other than VRM, may result in performance degradation. The nominal voltages for the reference bypass pins are as follows: VRM = 1.5 V VRP = VRM + VREF / 2 VRN = VRM - VREF / 2 Control Inputs Power-Down & Sleep (PD/Sleep) The power-down and sleep modes can be enabled through this three-state input pin. Table 2 shows how to utilize these options. 20 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 Table 2. Power Down/Sleep Selection Table PD Input Voltage Power State VA Power-down VA/2 Sleep AGND On The power-down and sleep modes allows the user to conserve power when the converter is not being used. In the power-down state all bias currents of the analog circuitry, excluding the reference are shut down which reduces the power consumption to 15 mW with no clock running. In sleep mode some additional buffer circuitry is left on to allow an even faster wake time; power consumption in the sleep mode is 50 mW with no clock running. In both of these modes the output data pins are undefined and the data in the pipeline is corrupted. The Exit Cycle time for both the sleep and power-down mode is determined by the value of the capacitors on the VRP, VRM and VRN reference bypass pins (pins 43, 44 and 45). These capacitors lose their charge when the ADC is not operating and must be recharged by on-chip circuitry before conversions can be accurate. For power-down mode the Exit Cycle time is about 3 ms with the recommended component values. The Exit Cycle time is faster for sleep mode. Smaller capacitor values allow slightly faster recovery from the power down and sleep mode, but can result in a reduction in SNR, SINAD and ENOB performance. Clock Mode Select/Data Format (CLK_SEL/DF) Single-ended versus differential clock mode and output data format are selectable using this quad-state function pin. Table 3 shows how to select between the clock modes and the output data formats. Table 3. Clock Mode and Data Format Selection Table CLK_SEL/DF Input Voltage Clock Mode Output Data Format VA Differential 2's Complement (2/3) * VA Differential Offset Binary (1/3) * VA Single-Ended 2's Complement AGND Single-Ended Offset Binary CLOCK INPUTS The CLK+ and CLK- signals control the timing of the sampling process. The CLK_SEL/DF pin (pin 8) allows the user to configure the ADC for either differential or single-ended clock mode. In differential clock mode, the two clock signals should be exactly 180 out of phase from each other and of the same amplitude. In the singleended clock mode, the clock signal should be routed to the CLK+ input and the CLK- input should be tied to AGND in combination with the correct setting from Table 3. To achieve the optimum noise performance, the clock inputs should be driven with a stable, low jitter clock signal in the range indicated in the Electrical Table. The clock input signal should also have a short transition region. This can be achieved by passing a low-jitter sinusoidal clock source through a high speed buffer gate. This configuration is shown in Figure 22. The trace carrying the clock signal should be as short as possible and should not cross any other signal line, analog or digital, not even at 90. Figure 22 shows the recommended clock input circuit. The clock signal also drives an internal state machine. If the clock is interrupted, or its frequency is too low, the charge on the internal capacitors can dissipate to the point where the accuracy of the output data will degrade. This is what limits the minimum sample rate. The clock line should be terminated at its source in the characteristic impedance of that line. Take care to maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905 (SNLA035) for information on setting characteristic impedance. It is highly desirable that the source driving the ADC clock pins only drive that pin. However, if that source is used to drive other devices, then each driven pin should be AC terminated with a series RC to ground, such that the resistor value is equal to the characteristic impedance of the clock line and the capacitor value is (6) Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 21 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com where tPD is the signal propagation rate down the clock line, "L" is the line length and ZO is the characteristic impedance of the clock line. This termination should be as close as possible to the ADC clock pin but beyond it as seen from the clock source. Typical tPD is about 150 ps/inch (60 ps/cm) on FR-4 board material. The units of "L" and tPD should be the same (inches or centimeters). The duty cycle of the clock signal can affect the performance of the A/D Converter. Because achieving a precise duty cycle is difficult, the ADC14V155 has a Duty Cycle Stabilizer. It is designed to maintain performance over a clock duty cycle range of 30% to 70%. DIGITAL OUTPUTS Digital outputs consist of the LVDS signals D0-D13, DRDY and OVR. The ADC14V155 has 16 LVDS compatible data output pins: 14 data output bits corresponding to the converted input value, a data ready (DRDY) signal that should be used to capture the output data and an over-range indicator (OVR) which is set high when the sample amplitude exceeds the 14-Bit conversion range. Valid data is present at these outputs while the PD/Sleep pin is low. The odd data bits should be captured with the falling edge of DRDY and the even data bits should be captured with the rising edge of DRDY. Be very careful when driving a high capacitance bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current flows through VDR and DRGND. These large charging current spikes can cause on-chip ground noise and couple into the analog circuitry, degrading dynamic performance. Adequate bypassing, limiting output capacitance and careful attention to the ground plane will reduce this problem. Additionally, bus capacitance beyond the specified 5 pF/pin will cause tOD to increase, reducing the setup and hold time of the ADC output data. The result could be an apparent reduction in dynamic performance. To minimize noise due to output switching, the load currents at the digital outputs should be minimized. This can be achieved by keeping the PCB traces less than 2 inches long; longer traces are more susceptible to noise. Try to place the 100 ohm termination resistor as close to the receiving circuit as possible. See Figure 22. +3.3V from Regulator +3.3V from Regulator +1.8V from Regulator 0.01 PF x3 0.01 PF 0.1PF 10 PF 0.1 PF 44 49.9 2 1k 24.9 V DR 25 V DR 36 DRGND DRGND 32 D13+/D12+ 31 D13-/D1230 D11+/D10+ 29 D11-/D1028 D9+/D8+ 27 D9-/D824 D7+/D6+ 23 D7-/D622 D5+/D4+ 21 D5-/D420 D3+/D2+ 19 D3-/D218 D1+/D0+ 17 D1-/D0- 100 100 100 100 100 100 100 100 100 + + - + + Receiver + + + + + - 26 35 0.1 PF CLK_SEL/DF 11 CLK+ 12 CLK- VA 1 7 PD 8 DGND PD CLK_SEL/DF 12.1 14 2 24.9 ADC14V155 3 VIN4 V + IN 0.1 PF Flux XFMR: ADT1-1WT or ETC1-1T Balun XFMR: ADT1-12 or ETC1-1-13 CLKIN 0.1 PF 15 pF 0.1 PF V RN V RP 12.1 24.9 V RM AGND AGND AGND AGND AGND AGND AGND 0.1 PF 1 DRDY+ 34 33 DRDY16 OVR+ 15 OVR- 2 5 10 38 39 42 47 VIN 43 0.1 PF 0.1 PF VREF 0.1 PF 45 10 PF VA VA VA VA VA VA VA 46 10 PF 0.1 PF x3 13 1 6 9 37 40 41 48 0.01 PF x6 VD 0.1 PF x6 1k NC7WV125K8X High Speed Buffer Figure 22. Application Circuit using Transformer Drive Circuit 22 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 POWER SUPPLY CONSIDERATIONS The power supply pins should be bypassed with a 0.1 F capacitor and with a 0.01 F ceramic chip capacitor close to each power pin. Leadless chip capacitors are preferred because they have low series inductance. As is the case with all high-speed converters, the ADC14V155 is sensitive to power supply noise. Accordingly, the noise on the analog supply pin should be kept below 100 mVP-P. No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be especially careful of this during power turn on and turn off. The VDR pin provides power for the output drivers and may be operated from a supply in the range of 1.6V to 2.0V. This enables lower power operation, reduces the noise coupling effects from the digital outputs to the analog circuitry and simplifies interfacing to lower voltage devices and systems. Note, however, that tOD increases with reduced VDR. LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining separate analog and digital areas of the board, with the ADC14V155 between these areas, is required to achieve specified performance. The ground return for the data outputs (DRGND) carries the ground current for the output drivers. The output current can exhibit high transients that could add noise to the conversion process. To prevent this from happening, the DRGND pins should NOT be connected to system ground in close proximity to any of the ADC14V155's other ground pins. Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the clock line as short as possible. Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane area. Generally, analog and digital lines should cross each other at 90 to avoid crosstalk. To maximize accuracy in high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the generally accepted 90 crossing should be avoided with the clock line as even a little coupling can cause problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to degradation of SNR. Also, the high speed clock can introduce noise into the analog chain. Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the signal path through all components should form a straight line wherever possible. Be especially careful with the layout of inductors and transformers. Mutual inductance can change the characteristics of the circuit in which they are used. Inductors and transformers should not be placed side by side, even with just a small part of their bodies beside each other. For instance, place transformers for the analog input and the clock input at 90 to one another to avoid magnetic coupling. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter's input pins and ground or to the reference input pin and ground should be connected to a very clean point in the ground plane. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed in the analog area of the board. All digital circuitry and dynamic I/O lines should be placed in the digital area of the board. The ADC14V155 should be between these two areas. Furthermore, all components in the reference circuitry and the input signal chain that are connected to ground should be connected together with short traces and enter the ground plane at a single, quiet point. All ground connections should have a low inductance path to ground. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 23 ADC14V155 SNAS397I - MARCH 2007 - REVISED APRIL 2013 www.ti.com DYNAMIC PERFORMANCE To achieve the best dynamic performance, the clock source driving the CLK input must have a sharp transition region and be free of jitter. Isolate the ADC clock from any digital circuitry with buffers, as with the clock tree shown in Figure 23 . The gates used in the clock tree must be capable of operating at frequencies much higher than those used if added jitter is to be prevented. Best performance will be obtained with a single-ended drive input drive, compared with a differential clock. As mentioned in LAYOUT AND GROUNDING, it is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can lead to reduced SNR performance, and the clock can introduce noise into other lines. Even lines with 90 crossings have capacitive coupling, so try to avoid even these 90 crossings of the clock line. Figure 23. Isolating the ADC Clock from other Circuitry with a Clock Tree 24 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 ADC14V155 www.ti.com SNAS397I - MARCH 2007 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision H (April 2013) to Revision I * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 24 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: ADC14V155 25 PACKAGE OPTION ADDENDUM www.ti.com 19-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) ADC14V155CISQ/NOPB ACTIVE Package Type Package Pins Package Drawing Qty WQFN RHS 48 250 Eco Plan Lead/Ball Finish (2) Green (RoHS & no Sb/Br) MSL Peak Temp Op Temp (C) Top-Side Markings (3) CU SN Level-3-260C-168 HR (4) -40 to 85 14V155SQ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADC14V155CISQ/NOPB Package Package Pins Type Drawing WQFN RHS 48 SPQ 250 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 178.0 16.4 Pack Materials-Page 1 7.3 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 7.3 1.3 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADC14V155CISQ/NOPB WQFN RHS 48 250 213.0 191.0 55.0 Pack Materials-Page 2 MECHANICAL DATA RHS0048A SQA48A (Rev B) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated