(KTQM77/mITX) KTQM77/mITX - KTHM76/mITX Users Guide KTD-N0850-F If it's embedded, it's Kontron KTD-N0850-F Page 2 Document details Document revision history. Revision Date By nd F Jan 2 2014 MLA E Jun13th 2013 MLA th MLA th D June 4 2013 C May 27 2013 MLA B Mar. 6 2013 th MLA A Feb. 19 2013 0 July 10 2012 th MLA th MLA Comment CPU list revised. BIOS part upgraded in according to BIOS Revision Release note (KTQM7715.bin). Added KTHM76/mITX. Minor corrections. Correction to AMT 8.0. Updated CPU list and RAM List. Several corrections. Added AMT short description. Correction to eDP and LVDS text. BIOS Recover text upgraded. Added note for PCIex2 support. BIOS information upgraded to BIOS 14. Page 67 corrected function name. Added to BIOS section: System Temperature Ext Type and Fan limits. Added cable kits. Corrected PCIex1 signals. Note on OS installation via USB. Removed 5V tolerance for some GPIO's. Jumper J37 info changed. 3.3V now 5% tolerance. Improved 12V only description. Updated CPU list. Revision of BIOS section. Completed System Resources. Preliminary version Copyright Notice: Copyright 2011, KONTRON Technology A/S, ALL RIGHTS RESERVED. No part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S. Trademark Acknowledgement: Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer: KONTRON Technology A/S reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Specifications listed in this manual are subject to change without notice. KONTRON Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or mask work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. KONTRON Technology A/S makes no representation or warranty that such application will be suitable for the specified use without further testing or modification. Life Support Policy KONTRON Technology's PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A/S. As used herein: Life support devices or systems are devices or systems which, (a) are intended for surgical implant into body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labelling, can be reasonably expected to result in significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 3 Document details KONTRON Technology Technical Support and Services If you have questions about installing or using your KONTRON Technology Product, check this User's Manual first - you will find answers to most questions here. To obtain support, please contact your local Distributor or Field Application Engineer (FAE). Before Contacting Support: Please be prepared to provide as much information as possible: * CPU Board 1. Type. 2. Part Number (find PN on label) 3. Serial Number if available (find SN on label) * Configuration 1. CPU Type, Clock speed 2. DRAM Type and Size. 3. BIOS Revision (Find the Version Info in the BIOS Setup). 4. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section). * System 1. O/S Make and Version. 2. Driver Version numbers (Graphics, Network, and Audio). 3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc. Warranty KONTRON Technology warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a similar product. Replacement Product or parts may include remanufactured or refurbished parts or components. The warranty does not cover: 1. Damage, deterioration or malfunction resulting from: A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. B. Repair or attempted repair by anyone not authorized by KONTRON Technology. C. Causes external to the product, such as electric power fluctuations or failure. D. Normal wear and tear. E. Any other causes which does not relate to a product defect. 2. Removal, installation, and set-up service charges. Exclusion of damages: KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR: 1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES. 2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. 3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 4 Contents Contents Introduction ............................................................................................. 7 1 Installation procedure ........................................................................ 8 1.1 Installing the board .......................................................................................................................... 8 1.2 Requirement according to IEC60950 ................................................................................................... 9 2 System Specification ........................................................................ 10 2.1 Component main data ..................................................................................................................... 10 2.2 System overview ............................................................................................................................. 14 2.3 Processor Support Table .................................................................................................................. 16 2.4 System Memory support................................................................................................................... 18 2.5 Graphics Subsystem ........................................................................................................................ 19 2.5.1 Intel HD Graphics 4000 .................................................................................................................. 19 2.5.2 Intel HD Graphics 3000 .................................................................................................................. 19 2.5.3 LVDS and DVI ................................................................................................................................ 20 2.5.4 Graphics Adapters ......................................................................................................................... 20 2.6 Power Consumption ........................................................................................................................ 21 3 Connector Locations ......................................................................... 27 3.1 Frontside ....................................................................................................................................... 27 3.2 IO Bracket area ............................................................................................................................... 28 3.3 Backside ........................................................................................................................................ 28 4 Connector Definitions ....................................................................... 29 5 IO-Area Connectors........................................................................... 30 5.1 Display connectors (IO Area) ............................................................................................................ 30 5.1.1 DVI Connector (DVI-I) (J41) ........................................................................................................... 30 5.1.2 DP Connectors (DP0/DP1) (J40/J39) ............................................................................................... 31 5.2 Ethernet Connectors ....................................................................................................................... 32 5.3 USB Connectors (IO Area) ................................................................................................................ 33 5.3.1 USB Connector 0/1 (USB0/1) ......................................................................................................... 34 5.3.2 USB Connector 2/3 (USB2/3) ......................................................................................................... 35 5.3.3 USB Connector 4/5 (USB4/5) ......................................................................................................... 35 5.4 Audio Connector (IO Area) ............................................................................................................... 36 6 Internal Connectors .......................................................................... 37 6.1 Power Connector (ATX/BTXPWR) ....................................................................................................... 37 6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29) ....................................................................... 38 6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J27)......................................................................... 39 6.4 Display connectors (Internal)........................................................................................................... 40 6.4.1 eDP connector (EDP) (J38) ............................................................................................................. 40 6.4.2 LVDS Flat Panel Connector (LVDS) (J20) ........................................................................................... 41 KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.5 Page 5 SATA (Serial ATA) Disk interface (J21 - J26) ...................................................................................... 42 6.6 USB Connectors (USB)..................................................................................................................... 43 6.6.1 USB Connector 6/7 ........................................................................................................................ 43 6.6.2 USB Connector 8/9 (USB8/9) (J10) ................................................................................................. 43 6.6.3 USB Connector 10/11 (USB10/11) (J11).......................................................................................... 44 6.6.4 USB Connector 12/13 (USB12/13) (J12).......................................................................................... 44 6.7 Firewire/IEEE1394 connectors (J13,J14)........................................................................................... 45 6.7.1 IEEE1394 connector (IEEE1394_0) (J14) ......................................................................................... 45 6.7.2 IEEE1394 connector (IEEE1394_1) (J13) ......................................................................................... 45 6.8 Serial COM1 - COM4 Ports (J15, J16, J17, J18)................................................................................... 46 6.9 Audio Connectors............................................................................................................................ 47 6.9.1 CDROM Audio Input (CDROM) (J3) ................................................................................................... 47 6.9.2 Line2 and Mic2 .............................................................................................................................. 47 6.9.3 Audio Header Connector (AUDIO_HEAD) (J31) ................................................................................. 48 6.9.4 Front Panel Connector (FRONTPNL) (J19) ........................................................................................ 49 6.10 Feature Connector (FEATURE) (J30) .................................................................................................. 50 6.11 "Load Default BIOS Settings" Jumper (J37) ....................................................................................... 53 6.12 SPI Recover Jumper (J4).................................................................................................................. 54 6.13 SPI Connector (SPI) (J5).................................................................................................................. 55 6.14 XDP-CPU (Debug Port for CPU) (J32) ................................................................................................. 56 6.15 XDP-PCH (Debug Port for Chipset) (J33) ............................................................................................ 57 7 Slot Connectors (PCIe, miniPCIe, PCI) ................................................ 58 7.1 PCIe Connectors.............................................................................................................................. 58 7.1.1 PCI-Express x16 Connector (PCIe x16).............................................................................................. 58 7.1.2 miniPCI-Express mPCIe0 (J34) ........................................................................................................ 60 7.1.3 miniPCI-Express mPCIe1 (J35) ........................................................................................................ 61 7.1.4 PCI-Express x1 Connector (PCIe x1) (J36) ........................................................................................ 62 8 On-board - & mating connector types ................................................. 63 9 System Resources ............................................................................. 64 9.1 Memory Map ................................................................................................................................... 64 9.3 Interrupt Usage .............................................................................................................................. 65 9.4 IO Map ........................................................................................................................................... 66 10 BIOS ................................................................................................ 67 10.1 Main .............................................................................................................................................. 67 10.2 Advanced ....................................................................................................................................... 68 10.2.1 Advanced - PCI Subsystem Settings ................................................................................................ 69 10.2.2 Advanced - APCI Settings .............................................................................................................. 72 10.2.3 Advanced - Trusted Computing ...................................................................................................... 73 10.2.4 Advanced - CPU Configuration ....................................................................................................... 74 10.2.5 Advanced - SATA Configuration ...................................................................................................... 76 10.2.6 Advanced - Intel TXT (LT) Configuration .......................................................................................... 80 10.2.7 Advanced - AMT Configuration ....................................................................................................... 81 10.2.8 Advanced - Acoustic Management Configuration ............................................................................. 83 10.2.9 Advanced - USB Configuration ....................................................................................................... 84 10.2.10 Advanced - SMART Settings ........................................................................................................... 86 10.2.11 Advanced - Super IO Configuration................................................................................................. 87 10.2.12 Advanced - Voltage Monitor .......................................................................................................... 93 10.2.13 Advanced - Hardware Health Configuration ..................................................................................... 94 10.2.14 Advanced - Displayblock Setup ...................................................................................................... 96 10.2.15 Advanced - LAN Configuration ....................................................................................................... 97 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 6 10.2.16 Advanced - Delay Startup .............................................................................................................. 99 10.2.17 Advanced - Serial Port Console Redirection ................................................................................... 100 10.2.18 Advanced - CPU PPM Configuration............................................................................................... 104 10.3 Chipset ........................................................................................................................................ 106 10.3.1 PCH-IO Configuration ................................................................................................................... 107 10.3.2 System Agent (SA) Configuration .................................................................................................. 113 10.4 Boot ............................................................................................................................................ 130 10.4.1 Force Boot Setup ......................................................................................................................... 132 10.4.2 CSM parameters........................................................................................................................... 133 10.5 10.5.1 10.5.2 10.5.3 Security ....................................................................................................................................... 134 Image Execution Policy ................................................................................................................ 135 Key Management ......................................................................................................................... 136 HDD Security Configuration .......................................................................................................... 137 10.6 Save & Exit ................................................................................................................................... 138 11 AMI BIOS Beep Codes ...................................................................... 139 12 OS Setup ........................................................................................ 140 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 7 Introduction Introduction This manual describes the KTQM77 family consisting of the KTQM77/mITX and the KTHM76/mITX boards made by KONTRON Technology A/S. In this Users Guide the boards will in general also be denoted KTQM77 and KTHM76 and if a subject is not depending on exact board type then both types of board will be denoted KTQM77. The KTQM77 and KTHM76 boards are based on the QM77 and HM76 chipset respectively and support rd 3 generation Intel(R) i7 -, i5 -, i3 2Core and 4Core mobile processors. See "Processor Support Table for more specific details. The KTQM77 family consist on members having same form factors, and the same functionality except for the functions listed in the table below. KTQM77 variants LAN IEEE 1394a RAID AMT eDP PCIe x16 Bifurcation KTQM77/mITX 3x 2x 0/1/5/10 AMT8.0 Yes Yes 4x USB3.0/2.0 10x USB2.0 KTHM76/mITX 1x No No No No No 4x USB3.0/2.0 8x USB2.0 USB Use of this Users Guide implies a basic knowledge of PC-AT hard- and software. This manual is focused on describing the KTQM77 board's special features and is not intended to be a standard PC-AT textbook. New users are recommended to study the short installation procedure stated in the following chapter before switching-on the power. All configuration and setup of the CPU board is either done automatically or manually by the user via the BIOS setup menus. Only exception is the "Load Default BIOS Settings" Jumper. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 8 Installation procedure 1 Installation procedure 1.1 Installing the board To get the board running, follow these steps. If the board shipped from KONTRON has already components like RAM, CPU and cooler mounted, then relevant steps below, can be skipped. 1. Turn off the PSU (Power Supply Unit) ! Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the PSU) or leave the Power Connectors unconnected while configuring the board. Otherwise components (RAM, LAN cards etc.) might get damaged. If not using single 12V power input make sure PSU has 3.3V monitoring watchdog (standard ATX PSU feature), running the board without 3.3V will damage the board within minutes. 2. Insert the DDR3 DIMM 204pin SODIMM module(s) Be careful to push it in the slot(s) before locking the tabs. For a list of approved DDR3 SODIMMs contact your Distributor or FAE. See also chapter "System Memory Support". 3. Install the processor The CPU is keyed and will only mount in the CPU socket in one way. Use suitable screwdriver to open/ close the CPU socket. Refer to supported processor overview for details. 4. Cooler Installation Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the FAN_CPU connector. 5. Connecting Interfaces Insert all external cables for hard disk, keyboard etc. A monitor must be connected in order to be able change BIOS settings. 6. Connect and turn on PSU Connect PSU to the board by the ATX/BTXPWR and the 4-pin ATX+12V connectors. For the KTQM77/mITX alternatively use only the 4-pin ATX+12V connector if single voltage operation (+12V +/-5%) is requested. 7. Power Button Depending on BIOS setting, the PWRBTN_IN must be toggled to start the Power supply; this is done by shorting pins 16 (PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector description). A "normally open" switch can be connected via the FRONTPNL connector. 8. BIOS Setup Enter the BIOS setup by pressing the <Del> key during boot up. Enter Exit Menu and Load Optimal Defaults. Refer to the "BIOS Configuration / Setup" section of this manual for details on BIOS setup. Note: To clear all BIOS settings, including Password protection, activate "Load Default BIOS Settings" Jumper for ~10 sec (without power connected). 9. Mounting the board to chassis ! Warning: When mounting the board to chassis etc. please notice that the board contains components on both sides of the PCB which can easily be damaged if board is handled without reasonable care. A damaged component can result in malfunction or no function at all. When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and having diameter of ~7mm. Note: Do not use washers with teeth, as they can damage the PCB and may cause short circuits. KTQM77 - KTHM76 Users Guide KTD-N0850-F Installation procedure Page 9 1.2 Requirement according to IEC60950 Users of KTQM77 should take care when designing chassis interface connectors in order to fulfil the IEC60950 standard: When an interface/connector has a VCC (or other power) pin, which is directly connected to a power plane like the VCC plane: To protect the external power lines of the peripheral devices, the customer has to take care about: * That the wires have suitable rating to withstand the maximum available power. * That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC60950. Lithium Battery precautions: CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by manufacturer. Dispose of used batteries according to the manufacturer's instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. Lever det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvant batteri enligt fabrikantens instruktion. VORSICHT! Explosionsgefahr bei unsachgemaem Austausch der Batterie. Ersatz nur durch den selben oder einen vom Hersteller empfohlenen gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. VAROITUS Paristo voi rajahtaa, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laltevalmistajan suosittelemaan tyyppiin. Havita kaytetty paristo valmistajan ohjeiden mukaisesti. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 10 System Specification 2 System Specification 2.1 Component main data The table below summarizes the features of the KTQM77/mITX embedded motherboard. Form factor KTQM77/mITX and KTHM76/mITX: miniITX (170,18 mm by 170,18 mm) Processor Support 2 and 3 Generation Intel(R) CoreTM (Sandy Bridge M and Ivy Bridge M respectively) and Intel(R) Celeron(R) processors via Socket G2 (rPGA 988B ) ZIF Socket * Intel(R) CoreTM i7 * Intel(R) CoreTM i5 * Intel(R) CoreTM i3 * Intel(R) Celeron(R) B810 Up to 1333MHz system bus and 2/3/4/6MB internal cache. Memory * * nd * * rd DDR3 SODIMM 204pin socket (2 sockets) Support single and dual ranks DDR3 1066/1333/1600MT/s (PC3-8500/PC3-10600/PC3-12800) Support system memory from 256MB and up to 2x 8GB. Notes:Less than 4GB displayed in System Properties using 32bit OS (Shared Video Memory/PCI resources is subtracted) ECC not supported (PGA processors do not support ECC) Chipset Intel QM77 /HM77 PCH (Platform Controller Hub) * Intel (R) VT-d (Virtualisation Technology for Directed I/O) * Intel (R) TXT (Trusted Execution Technology) * Intel (R) vPRO (KTQM77 only) * Intel (R) AMT (Active Management Technology) version 8.0 (KTQM77 only) * Intel (R) AT (Anti-Theft Technology) * Intel (R) HD Audio Technology * Intel (R) RST (Rapid Storage Technology) * Intel (R) RRT (Rapid Recover Technology) * SATA (Serial ATA) 6Gb/s and 3Gb/s. * USB revision 2.0 * USB revision 3.0 * PCI Express revision 2.0 * ACPI 3.0b compliant * Dual or Triple Display support (Dual/Triple Graphic Pipes, depends on CPU) * Blue-ray HD video playback Security * Intel(R) Integrated TPM 1.2 support Management * Intel(R) Active Management Technology (Intel(R) AMT) 8.0 (KTQM77 only) Audio Audio, 7.1 Channel High Definition Audio Codec using the VIA VT1708S codec * Line-out * Line-in * Surround output: SIDE, LFE, CEN, BACK and FRONT * Microphone: MIC1 and MIC2 * CDROM in * SPDIF (electrical Interface only) * On-board speaker (Electromagnetic Sound Generator like Hycom HY-05LF) KTQM77 - KTHM76 Users Guide KTD-N0850-F Video Page 11 System Specification rd Intel i3, i5 & i7 3 Generation Mobile processors support Intel HD Graphics 4000. nd Intel i3, i5 & i7 2 Generation Mobile processor supports Intel HD Graphics 3000. Intel Celeron Processor B810 supports Intel HD Graphics. eDP (Embedded DisplayPort) directly from processor. (KTQM77 only). Analogue VGA and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel (R) QM77 Chipset. * * * * * * * * * VGA (analogue panel) via DVI-I (sharing DVI-I connector with DVI-D) DVI-D (sharing DVI-I connector with analogue VGA) 2x DP (DisplayPorts), comply with DisplayPort 1.2 specification. LVDS panel support up to 24 bit, 2 pixels/clock and 1920x1200. HDMI panel support via DP to HDMI Adapter Converter. Second VGA panel support via DP to VGA Adapter Converter. Second DVI panel support via DP to DVI Adapter Converter. Dual independent pipes for Mirror and Dual independent display support (exception is combination LVDS and eDP) Triple independent pipes (Intel HD Graphics 4000 only) for triple independent or cloned displays are supported from OS. Any 3 displays via DP0, DP1, DVI-D or DVI-A, LVDS or eDP can be used, but only active DP to DVI/HDMI converters can be used. I/O Control Via ITE IT8516E Embedded Controller and Nuvoton W83627DHG I/O Controller (both via LPC Bus interface) Peripheral interfaces * * * * * * * * * * * Two USB 2.0 ports on I/O area Four USB 3.0 / USB 2.0 on I/O area Eight USB 2.0 ports on internal pinrows (KTQM77 only) Six USB 2.0 ports on internal pinrows (KTHM76 only) Two IEEE 1394a-2000 (up to 400M bits/s) on internal pinrows (KTQM77 only) Four Serial ports (RS232) on internal pinrows Two Serial ATA-600 IDE interfaces Four Serial ATA-300 IDE interfaces RAID 0/1/5/10 support (KTQM77 only) mSATA via mPCIe_0 connector PS/2 keyboard and mouse ports via pinrow LAN Support * 1x 10/100/1000Mbits/s LAN (ETHER1) using Intel(R) Lewisville 82579LM Gigabit PHY connected to QM77 supporting AMT 8.0 (AMT only on KTQM77) 2x 10/100/1000Mbits/s LAN (ETHER2/ETHER3)using Intel(R) Hartwell 82574L PCI Express controllers (KTQM77 only) PXE Netboot supported. Wake On LAN (WOL) supported * * * Expansion Capabilities * * * * * * * * * PCI-Express slot(s): o 1 slot PCIe x16 (PCIe 2.0 and up to PCIe 3.0 when using Ivy Bridge CPU) o 1 slot PCIe x1 (PCIe 2.0): o 1 slot miniPCI-Express (PCI Express or mSATA signals, no USB signals) o 1 slot miniPCI-Express (PCI Express signals, no mSATA or USB signals) SMBus, compatible with ACCES BUS and I2C BUS, (via Feature connector) SPI bus routed to SPI connector DDC Bus routed to DVI-I connector 18 x GPIOs (General Purpose I/Os), (via Feature connector) DAC, ADC, PWM and TIMER (Multiplexed), (via Feature connector) WAKE UP / Interrupt Inputs (Multiplexed), (via Feature connector) 3 Wire Bus for GPIO Expansion (up to 152 GPIOs), (via Feature connector) 8 bit Timer output, (via Feature connector) KTQM77 - KTHM76 Users Guide KTD-N0850-F Hardware Monitor Subsystem * * * * * * * Page 12 System Specification Smart Fan control system, support Thermal(R) and Speed(R) cruise for two on-board Fan connectors: CPU Fan (on-board) and System Fan (on-board) Smart Fan control system, support Speed(R) cruise for two off-board Fans (Fan3/Fan4) via Feature Connector. Three thermal inputs: CPU Die temperature (precision +/- 3C), System temperature (precision +/- 3C) and System Temperature External via Feature Connector (precision +/- 1C). Voltage monitoring Intrusion (Case Open) detect input, (via Feature connector) Sleep S5# Indication, (via Feature connector) System Powergood Signal, (via Feature connector) Power Supply Unit ATX/BTX (w. ATX+12V) PSU for full PCI/PCIe load. Alternatively (mITX version only): +12V single supply via ATX+12V (4-pole) connector, but with limitation to power load (especially +5V for USB). Battery Exchangeable 3.0V Lithium battery for on-board Real Time Clock and CMOS RAM. Manufacturer Panasonic / Part-number CR-2032L/BN, CR2032N/BN or CR-2032L/BE. Approximate 6.2 years retention. Current draw is 4.1A when PSU is disconnected and 0 A in S0 - S5. CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. BIOS Operating Systems Support * * * * * * * * * * * * * Kontron Technology / AMI BIOS (EFI core version) Support for ACPI 3.0 ( Advanced Configuration and Power Interface), Plug & Play o Suspend (S1 mode) o Suspend To Ram (S3 mode) o Suspend To Disk (S4 mode) "Always On" BIOS power setting RAID Support (RAID modes 0,1, 5 and 10) KTQM77/mITX only) WinXP (32b + 64b *) Vista (32b * + 64b *) Windows 7 (32b + 64b *) Linux VxWorks Windows Server 2003 r2 (32b * + 64b *) Windows Server 2008 r2 (32b * + 64b *) WES7 (32b + 64b) *= Out Of The Box installation test only. KTQM77 - KTHM76 Users Guide KTD-N0850-F Environmental Conditions Page 13 System Specification Operating: 0C - 60C operating temperature (forced cooling). It is the customer's responsibility to provide sufficient airflow around each of the components to keep them within allowed temperature range. 10% - 90% relative humidity (non-condensing) Storage: -20C - 70C; lower limit of storage temperature is defined by specification restriction of on-board CR2032 battery. Board with battery has been verified for storage temperature down to -40C by Kontron. 5% - 95% relative humidity (non-condensing) Electro Static Discharge (ESD) / Radiated Emissions (EMI): All Peripheral interfaces intended for connection to external equipment are ESD/ EMI protected. EN 61000-4-2:2000 ESD Immunity EN55022:1998 class B Generic Emission Standard. Safety: nd IEC 60950-1: 2005, 2 Edition UL 60950-1 CSA C22.2 No. 60950-1 Product Category: Information Technology Equipment Including Electrical Business Equipment Product Category CCN: NWGQ2, NWGQ8 File number: E194252 Theoretical MTBF: 269.335 / 132.342 hours @ 40C / 60C for the KTQM77/mITX >269.335 / >132.342 hours @ 40C / 60C for the KTHM76/mITX Restriction of Hazardous Substances (RoHS): The KTQM77/mITX and KTHM76/mITX are RoHS compliant. Capacitor utilization: No Tantalum capacitors on board Only Japanese brand Solid capacitors rated for 100 C used on board KTQM77 - KTHM76 Users Guide KTD-N0850-F System Specification Page 14 2.2 System overview The block diagram below shows the architecture and main components of the KTQM77. The key (R) component on the board is the Intel QM77 (Panther Point) Mobile Express Chipset. Some components (PCI slots) are optional depending on board type. More detailed block diagram on next page. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 15 2x SODIMM DDR3 Embedded DisplayPort System Specification Sandy Bridge or Ivy Bridge Processor rPGA PCIe x16 (x16slot) PCIe x1 mPCIe (no USB) mPCIe/mSATA (no USB) 2x DisplayPort DVI-I 4x USB3.0/USB2.0 10x USB2.0 (QM77) 8x USB2.0 (HM76) PCIe to Firewire: 2x IEEE 1394a QM77 or HM76 PCH 1x 10/100/Gbe 2x 10/100/Gbe (QM77) VIA Audio Codec 2x SATA3.0 4x SATA2.0 mSATA (SATA2 signals mPCIe connector) RAID 0/1/5/10 (QM77) SPI BIOS Flash TPM (Infineon) Feature connector: SMBus/I2C Nuvoton W83627DHG COM3 & COM4 GPIO/DAC/ADC/PWM GPIO expansion up to 152 Intruder Embedded Controller ITE8516 COM1 & COM2 2x Fan (CPU/System) 6-pin PS/2 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 16 System Specification 2.3 Processor Support Table KTQM77 is designed to support the following PGA 988 processors (up to 55W power consumption): nd rd nd rd nd rd 2 / 3 generation Intel(R) CoreTM i7 processor 2 / 3 generation Intel(R) CoreTM i5 processor 2 / 3 generation Intel(R) CoreTM i3 processor Intel(R) Celeron(R) processor In the following list you will find all CPU's supported by the chipset in according to Intel but also other CPU's if successfully tested. Embedded CPU's are indicated by green text, successfully tested CPU's are indicated by highlighted text, successfully tested embedded CPU's are indicated by green and highlighted text and failed CPU's are indicated by red text. 4 4 8 8 6 6 6 6 6 6 6 4 4 8 8 6 8 6 6 6 6 3 3 3 3 3 3 3 3 3 3 3 3540M 3520M 3840QM 3820QM 3740QM 3720QM 3630QM 3610QM 3610QE* 3632QM 3612QM SR0X6 SR0MU SR0UT SR0MK SR0UV SR0ML SR0UX SR0MN SR0NP SR0V0 SR0MQ SR03R SR03F SR02X SR02E SR02W SR012 SR02N SR014 SR02T SR02Y SR0X7 SR0MV SR0XA SR0QJ SR0MX SR0WY SR0MZ SR044 SR048 SR02U SR04B L1 L1 E1 E1 E1 E1 E1 E1 E1 E1 E1 J1 J1 D2 D2 D2 D2 D2 D2 D2 D2 L1 L1 L1 L1 L1 L1 L1 J1 J1 D2 J1 2640M 2620M 2860QM 2920XM 2760QM 2820QM 2670QM 2720QM 2710QE* 2630QM 3380M 3360M 3340M 3610ME* 3320M 3230M 3210M 2540M 2520M 2510E* 2410M Thermal Design Power MB Stepping MHz 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1066/1333 1066/1333 1066/1333/1600 1066/1333/1600 1066/1333/1600 1066/1333/1600 1066/1333 1066/1333/1600 1066/1333/1600 1066/1333 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1333/1600 1066/1333 1066/1333 1066/1333 1066/1333 sSpec number 4 4 8 8 8 8 6 8 8 8 8 4 4 8 8 8 8 8 8 8 8 4 4 4 4 4 4 4 4 4 4 4 CPU Number 2 2 4 4 4 4 4 4 4 4 4 2 2 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 Cache CoreTM i5 nd 2 gen. 3.7 3.6 3.8 3.7 3.7 3.6 3.4 3.3 3.3 3.2 3.1 3.5 3.4 3.6 3.5 3.5 3.4 3.1 3.4 3.0 2.9 3.6 3.5 3.4 3.3 3.3 3.2 3.1 3.3 3.2 3.1 2.9 Bus Speed CoreTM i5 rd 3 gen. GHz 3.0 2.9 2.8 2.7 2.7 2.6 2.4 2.3 2.3 2.2 2.1 2.8 2.7 2.5 2.5 2.4 2.3 2.2 2.2 2.1 2.0 2.9 2.8 2.7 2.7 2.6 2.6 2.5 2.6 2.5 2.5 2.3 Threads CoreTM i7 nd 2 gen. GHz Cores CoreTM i7 rd 3 gen. Turbo Speed Processor Brand Clock Speed Some processors in the list are distributed from Kontron, those CPU's are marked by an * (asterisk). However please notice that this marking is only guide line and maybe not fully updated. C/W 105/35 105/35 105/45 105/45 105/45 105/45 105/45 105/45 105/45 105/35 105/35 100/35 100/35 100/45 100/55 100/45 100/45 100/45 100/45 100/45 100/45 105/35 105/35 105/35 105/35 105/35 105/35 105/35 100/35 100/35 100/35 100/35 KTQM77 - KTHM76 Users Guide Cache MHz MB CPU Number sSpec number Stepping GHz 2.6 2.5 2.4 2.4 2.4 2.3 2.2 2.2 2.2 2.1 2.1 - 1.6 1.6 - 2 1 Thermal Design Power Bus Speed Celeron(R) Threads CoreTM i3 nd 2 gen. GHz System Specification Cores CoreTM i3 rd 3 gen. Turbo Speed Processor Brand Page 17 Clock Speed KTD-N0850-F 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 1333/1600 1333/1600 1333/1600 1333/1600 1066/1333 1066/1333 1066/1333 1066/1333 1066/1333 1066/1333 1066/1333 3 3 3 3 3 3 3 3 3 3 3 3130M 3120M 3120ME 3110M 2370M 2350M 2330E 2330M 2328M 2312M 2310M SR0XC SR0TX SR0QM* SR0N2 SR0DP SR0DN SR02V* SR04J SR0TC SR09S SR04R L1 L1 L1 L1 J1 J1 D2 J1 J1 J1 J1 90/35 90/35 105/35 90/35 85/35 85/35 100/35 85/35 85/35 85/35 85/35 2 1 1066/1333 1066/1333 2 1.5 B810 B710 SR088* Q0 100/35 100/35 C/W Note: Sufficient cooling must be applied to the CPU in order to remove the effect as listed in above table (Thermal Guideline). The sufficient cooling is also depending on the maximum (worst-case) ambient operating temperature and the actual load of processor. The Kontron PN 1044-9447 is "Active Cooler for KTQM67/KTQM77" capable of being used for processors (fully loaded) having Thermal Guideline up to 45W @ 60C ambient temperature. MTBF is 70.000 hours @ 40C. The Kontron PN 1052-6345 "Cooler Active KTQM67 35W 33mm longlife" is capable of being used for processors (fully loaded) having Thermal Guideline up to 35W @ 60C ambient temperature. It support 1U and has long life (MTBF is 200.000 hours @ 60C). All the processors in the list above, inclusive the Celeron processor, are supporting the Enhanced Intel(R) SpeedStep(R) which is improved SpeedStep technology for faster transition between voltage (power saving states) and frequency states with the result of improved power/performance balance. Intel(R) Turbo Boost Technology 2.0 is supported by i5 and i7, as indicated in above list of processors, and is enabling overclocking of all cores, when operated within the limits of thermal design power, temperature and current. Intel(R) vPro Technology is supported by some of the i5 and i7 (not by Core i3) (KTQM77/mITX only). Intel AMT (Active Management Technology) (supported by KTQM77/mITX only) is a part of vPRO and is hardware and firmware technology that builds certain functionality into business PCs in order to remotely monitor, maintain, update, upgrade, and repair PCs. Intel AMT relies on a hardware-based out-of-band (OOB) communication channel that operates below the OS level, the channel is independent of the state of the OS (present, missing, corrupted, down). The communication channel is also independent of the PC's power state (however standby power required), the presence of a management agent, and the state of many hardware components (such as hard disk drives and memory). AMT is not intended to be used by itself; it is intended to be used with a software management application based on 3rd party software. If AMT is not required then KTHM65/KTHM76 might be an alternative or AMT can be disabled in BIOS. For more information search for "AMT" on Intel Homepage. rd PCIex2 is only supported on the PCIex16 slot if using 3 Generation Core2 CPU's (Ivy Bridge). KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 18 System Specification 2.4 System Memory support The KTQM77 has two DDR3 SODIMM sockets. The sockets support the following memory features: * * * * * 1.5V (only) 204-pin DDR3 SODIMM with gold-plated contacts Single/dual rank unbuffered DDR3 1333/1600MT/s (PC3-10600/PC3-12800) From 256MB and up to 2x 8GB. (up to 2x4GB tested) Notes: Less than 4GB displayed in System Properties using 32bit OS (Shared Video Memory/PCI resources is subtracted) SPD timings supported ECC not supported (PGA processors do not support ECC) The installed DDR3 SODIMM should support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the BIOS will attempt to configure the memory settings, but performance and reliability may be impacted. Memory Operating Frequencies Regardless of the SODIMM type used, the memory frequency will either be equal to or less than the processor system bus frequency. For example, if DDR3 1600 memory is used with a 1333 MHz system bus frequency processor, the memory clock will operate at 666 MHz. The table below lists the resulting operating memory frequencies based on the combination of SODIMMs and processors. DIMM Type Module name Memory Data transfers DDR3 1333 DDR3 1600 DDR3 1600 PC3-10600 PC3-12800 PC3-12800 Mill/s 1333 1600 1600 Processor system bus frequency MHz 1333 or more 1333 max 1600 Resulting memory clock frequency Peak transfer rate MHz 666 666 800 MB/s 10666 10666 12800 Notes: Kontron offers the following DDR3 204P SODIMM: PN 1054-3780 1GB, 1333MHZ, PC3-10600 PN 1054-3776 1GB, 1600MHZ, PC3-12800 PN 1054-3781 2GB, 1333MHZ, PC3-10600 PN 1051-5403 2GB, 1600MHZ, PC3-12800 PN 1054-3782 4GB, 1333MHZ, PC3-10600 PN 1051-9057 4GB, 1600MHZ, PC3-12800 PN 1054-3783 8GB, 1333MHZ, PC3-10600 PN 1054-3775 8GB, 1600MHZ, PC3-12800 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 19 System Specification 2.5 Graphics Subsystem rd The KTQM77 equipped with Intel 3 Gen i3, i5 or i7 processor, supports Intel HD Graphics 4000, nd equipped with Intel 2 Gen i3, i5 or i7 processor the Intel HD Graphics 3000 is supported and equipped with Intel Celeron Processor B810 the Intel HD Graphics is supported. The KTQM77/mITX support eDP (Embedded DisplayPort) directly from processor, and both KTQM77/mITX and KTHM76/mITX supports analogue VGA and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel Chipset (QM77 or HM76). The Analogue VGA and DVI-D are sharing the DVI-I connector. The PCH supports High-bandwidth Digital Content Protection for high definition content playback over digital interfaces. The PCH also integrates audio codecs for audio support over DP interfaces. Up to three displays (any of: DP0, DP1, DVI-D or DVI-A, LVDS or eDP (QM77 only)) can be activated at the same time and be used to implement independent or cloned display configuration. PCIe and PCI graphics cards can be used to replace on-board graphics or in combination with on-board graphics. 2.5.1 Intel HD Graphics 4000 Features of the Intel HD Graphics 4000 build into the i3, i5 and i7 processors, includes: * High quality graphics engine supporting o DirectX11 and OpenGL 4.0 compliant o Shader Model 5.0 support o Intel (R) Clear Video HD Technology o Intel (R) Quick Sync Video Technology o Intel (R) Flexible Display Interface (Intel (R) FDI) o Core frequency of 650 - 1150 (Turbo) MHz o Memory Bandwidth up to 21.3 GB/s o 16 3D Execution Units o 1.62 GP/s and 2.7 GP/S pixel rate (eDP and DP outputs) o Hardware Acceleration CVT HD and QSV o Dynamic Video Memory Technology (DVMT) support up to 1720 MB * eDP (Embedded DisplayPort on QM77) (Not in combination with LVDS) * DP0 and DP1 o 24/30 bit colours in WQXGA (2560x1600 pixels) and HDCP. o DisplayPort standard 1.2 2.5.2 Intel HD Graphics 3000 Features of the Intel HD Graphics 3000 build into the i3, i5 and i7 processors, includes: * High quality graphics engine supporting o DirectX10.1 and OpenGL 3.0 compliant o Shader Model 4.1 support o Intel (R) Clear Video HD Technology o Intel (R) Quick Sync Video Technology o Intel (R) Flexible Display Interface (Intel (R) FDI) o Core frequency of 350 - 1300 (Turbo) MHz o Memory Bandwidth up to 21.3 GB/s o 12 3D Execution Units o 1.62 GP/s and 2.7 GP/S pixel rate (eDP and DP outputs) o Hardware Acceleration full MPEG2, full VC-1 and full AVC o Dynamic Video Memory Technology (DVMT) support up to 1720 MB * eDP (Embedded DisplayPort on QM77) (Not in combination with LVDS) * DP0 and DP1 o 24/30 bit colours in WQXGA (2560x1600 pixels) and HDCP. o DisplayPort standard 1.1a KTQM77 - KTHM76 Users Guide KTD-N0850-F 2.5.3 Page 20 System Specification LVDS and DVI * LVDS panel Support (optional), 18/24 bit colours in up to WUXGA (1920x1200) @60 Hz and SPWG (VESA) colour coding. OpenLDI (JEIDA) colour coding is 18 bit with or without Dithering. (Not in combination with eDP (QM77 only)). * DVI-I (Digital Visual Interface) o Either DVI-A or DVI-D can be used via DVI-I connector o DVI-A Analogue Display (CRT) o 300 MHz Integrated 24-bit RAMDAC o Up to QXGA (2048x1536 pixels) @ 75 Hz refresh o DVI-D Digital Display up to WUXGA (1920x1200 pixels) @60 Hz 2.5.4 Graphics Adapters Use of DP Adapter Converters can implement HDMI support or second VGA or DVI panel support. The HDMI interface supports the HDMI 1.4a specification including audio codec. However limitations to the resolution apply: 2048x1536 (VGA), 1920x1200 (HDMI and DVI) 1051-7619 Cable DP Extender cable 200mm (when using two DP converters) DP to VGA PN 1045-5779 DP to HDMI DP to DVI-D PN 1045-5781 PN 1045-5780 Notice that only the DP to VGA adapter is an "active" converter the HDMI and DVI converters are passive and cannot be used in a triple panel configuration. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 21 System Specification 2.6 Power Consumption In order to ensure safe operation of the board, the ATX12V power supply must monitor the supply voltage and shut down if the supplies are out of range - refer to the hardware manual for the actual power supply specification. Please note, In order to keep the power consumption to a minimal level, boards do not implement a guaranteed minimum load. In some cases, this can lead to compatibility problems with ATX power supplies, which require a minimum load to stay in regulation. The KTQM77/mITX board is powered through the ATX+12V (4-pole) connector and optionally also ATX/BTX (24-pole) connector. Single 12V supply: When powered by 12V only (via ATX+12V connector) then limitations apply to +5V, where 14x USB, LVDS panel or eDP panel, COM ports, LPT port and Frontpanel connector shares 9.5A. 4-pole connector power limitation is 145W maximum, but if required more +12V power can be added via +12V (and GND) terminals in the 24-pin power connector. It is allowed to use the +12V and +5V from the 24-pole connector in order to drive external devices, but please notice that it is not allowed to use the SB5V, POK and PSON# signals. ATX12V supply: When powered as standard ATX12V then both ATX+12V connector and ATX/BTX connector must be used in according to the ATX12V PSU standard. Warning: Hot Plugging power supply is not supported. Hot plugging might damage the board. The requirements to the supply voltages are as follows: Supply Min Max Note VCC3.3 3.135V 3.465V Should be 5% for compliance with the ATX specification Vcc 4.75V 5.25V Should be 5% for compliance with the ATX specification. Should be +5/ -0% to meet the USB standard. +12V 11.4V 12.6V Should be 5% for compliance with the ATX specification -12V -13.2V -10.8V Should be 10% for compliance with the ATX specification -5V -5,50V -4.5V Not required for the KTQM77 boards 5VSB 4.75V 5.25V Should be 5% for compliance with the ATX specification Total System power example TBD CPU? @ ? GHz, ? GB Ram, 1x xxxgb HDD, 1x DVD-ROM, PSU Power Supplied via Operation ATX + 12V 12V Only Windows 7 32bit Idle 33W 36W Windows 7 32bit 3Dmark 2003 70W-88W 72W-96W Windows 7 32bit Intel Thermal Load 111W 111W Note: Listed power consumptions are inclusive 15 - 25W for PSU, HDD and DVD. More detailed Static Power Consumption TBD On the following pages the power consumption of different boards in different configurations are listed. For each configuration the power consumptions result are listed in 5 tables: 1- DOS, idle, mean 2- Windows7, Running 3DMARK 2005 & BiT 6, mean 3- S0, mean 4- S3, mean 5- S5, mean Note: some S5 measurements have been carried out in two sub modes M3 and Moff. Only S5/M3 mode maintains power to the circuits used for AMT and waking up the system via LAN, Keyboard and USB, while both S5/M3 and S5/Moff maintain power to RTC, Power Button In circuit and CMOS data. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 22 System Specification The principal test system and test equipment used TBD 1. 2. 3. 4. 5. 6. Tektronix TDS5104B Tektronix TCPA300 Tektronix TCP312 Fluke 289 Fluke 179 ATX rail switch Gnd KTQM77 PSU ATX supplies Current Probe Tektronix TDS5104B Note: Power consumption of PSU (power loss), Monitor and HDD are not included. The following four configurations (a - d) have been tested TBD a) Low Power Setup KTQM77/mITX ATX+12V PSU b) Low Power Setup KTQM77/mITX +12V only PSU Standard system configuration equipped with PCIex1 card, Internal graphics, 2x SATA disks, Intel i5 CPU, 1x SODIMM (1GB Modules), Monitor, Keyboard & Mouse. 1x 1-4GB USB Stick, 12V active cooler (KT), PSU (Corsair 430W) c) High Power Setup KTQM77/mITX ATX+12V PSU d) High Power Setup KTQM77/mITX +12V only PSU Standard system configuration equipped with PCIex1, PCIex16, miniPCIe WLAN, 4x SATA disks, Intel i7 CPU, 2x SODIMM (1GB Modules), Monitor, Keyboard & Mouse, 4x 1-4GB USB Sticks, 12V active cooler (KT), PSU (Corsair 430W). KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 23 System Specification a) Low Power Setup KTQM77/mITX ATX+12V PSU TBD DOS Idle, Mean, No external load Current draw Supply [A] +12V 0,140 +12V P4 1,222 +5V 0,411 +3V3 0,557 -12V 0,035 5VSB 0,007 Total Power consumption [W] 1,680 14,664 2,055 1,838 0,42 0,035 20,7 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6 Current draw Supply [A] +12V 0,165 +12V P4 3,250 +5V 0,450 +3V3 0,577 -12V 0,046 5VSB 0,007 Total Power consumption [W] 1,980 39,000 2,250 1,904 0,552 0,035 45,7 S0 Mode, Mean, No external load Current draw Supply [A] +12V 0,107 +12V P4 0,510 +5V 0,336 +3V3 0,576 -12V 0,043 5VSB 0,007 Total Power consumption [W] 1,284 6,120 1,680 1,901 0,516 0,035 11,5 S3 Mode, Mean, No external load Current draw Supply [A] 5VSB 0,218 Total Power consumption [W] 1,090 1,09 S5 Mode, Mean, No external load Current draw Supply [A] 5VSB 0,213 Total Power consumption [W] 1,065 1,07 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 24 System Specification b) Low Power Setup KTQM77/mITX +12V only PSU TBD DOS Idle, Mean, No external load Current draw Supply [A] +12V P4 1,721 Total Power consumption [W] 20,652 20,7 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6 Current draw Supply [A] +12V P4 3,940 Total Power consumption [W] 47,28 47,3 S0 Mode, Mean, No external load Current draw Supply [A] +12V P4 0,992 Total Power consumption [W] 11,904 11,9 S3 Mode, Mean, No external load Current draw Supply [A] +12V P4 0,099 Total Power consumption [W] 1,188 1,19 S5 Mode, Mean, No external load Current draw Supply [A] +12V P4 0,098 Total Power consumption [W] 1,176 1,18 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 25 System Specification c) High Power Setup KTQM77/mITX ATX+12V PSU TBD DOS Idle, Mean, No external load Current draw Supply [A] +12V 0,932 +12V P4 1,102 +5V 0,452 +3V3 0,553 -12V 0,036 5VSB 0,007 Total Power consumption [W] 11,184 13,224 2,260 1,825 0,432 0,035 29,0 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6 Current draw Supply [A] +12V 1,355 +12V P4 4,663 +5V 0,474 +3V3 0,968 -12V 0,049 5VSB 0,007 Total Power consumption [W] 16,260 55,956 2,370 3,194 0,588 0,035 78,4 S0 Mode, Mean, No external load Current draw Supply [A] +12V 0,569 +12V P4 0,485 +5V 0,420 +3V3 0,964 -12V 0,049 5VSB 0,007 Total Power consumption [W] 6,828 5,820 2,100 3,812 0,588 0,035 18,6 S3 Mode, Mean, No external load Current draw Supply [A] 5VSB 0,226 Total Power consumption [W] 1,130 1,13 S5 Mode, Mean, No external load Current draw Supply [A] 5VSB 0,219 Total Power consumption [W] 1,095 1,10 KTQM77 - KTHM76 Users Guide KTD-N0850-F System Specification Page 26 d) High Power Setup KTQM77/mITX +12V only PSU TBD DOS Idle, Mean, No external load Current draw Supply [A] +12V P4 2,499 Total Power consumption [W] 29,988 30,0 Windows 7, mean 3DMARK2005 ( first scene ) & BiT 6 Current draw Supply [A] +12V P4 6,712 Total Power consumption [W] 80,544 80,5 S0 Mode, Mean, No external load Current draw Supply [A] +12V P4 1,615 Total Power consumption [W] 19,38 19,4 S3 Mode, Mean, No external load Current draw Supply [A] +12V P4 0,104 Total Power consumption [W] 1,248 1,24 S5 Mode, Mean, No external load Current draw Supply [A] +12V P4 0,101 Total Power consumption [W] 1,212 1,21 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 27 Connector Location 3 Connector Locations 3.1 Frontside Sata1 Sata4 Sata2 Sata0 Sata5 Sata3 USB11 USB10 (see note below) FEATURE ATX/ BTXPWR USB13 USB12 USB9 USB8 System Temperature Sensor( R916) ATX+12V DDR3 Slot 1 DDR3 Slot 0 FRONTPNL EDP FAN_CPU FAN_SYS PCIe x16 COM4 COM3 PCIe x1 COM2 SPI recover COM1 SPI IEEE1394_1 IEEE1394_0 CDROM KBDMSE AUDIO_HEAD ETH1 USB5 USB4 Notes: ETH2 ETH3 USB1 USB0 DP0 USB3 USB2 DP1 Audio DVI-I LVDS Load Default BIOS Settings Sata0/Sata1support up to 6GB/s and Sata2/Sata3/Sata4/Sata5 support up to 3GB/S. SATA2 is shared with mPCIe0. USB0 - USB3 supports USB3.0/USB2.0. Not available connectors on KTHM76/mITX: IEEE 1394_0, IEEE 1394_1, ETH2, ETH3 and EDP. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 28 Connector Location 3.2 IO Bracket area ETH1 USB5 USB4 ETH2 ETH3 (KTQM77 only) USB1 USB0 DP0 USB3 USB2 DP1 DVI-I Audio 3.3 Backside PCB no. XDP-CPU (*) mPCIe1 XDP-PCH (*) below mPCIe1 mPCIe0 LPT (*) (*) The XDP and LPT connectors are not supported and not mounted in volume production. Kontron sub-supplier number. Please use the SN label on the PCIe x16 slot which is the board SN matching the SN in BIOS. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 29 Connector Definitions 4 Connector Definitions The following sections provide pin definitions and detailed description of all on-board connectors. The connector definitions follow the following notation: Column name Description Pin Shows the pin-numbers in the connector. The graphical layout of the connector definition tables is made similar to the physical connectors. Signal The mnemonic name of the signal at the current pin. The notation "XX#" states that the signal "XX" is active low. Type AI: AO: I: IO: IOT: IS: IOC: IOD: NC: O: OC: OT: LVDS: PWR: Analogue Input. Analogue Output. Input, TTL compatible if nothing else stated. Input / Output. TTL compatible if nothing else stated. Bi-directional tristate IO pin. Schmitt-trigger input, TTL compatible. Input / open-collector Output, TTL compatible. Input / Output, CMOS level Schmitt-triggered. (Open drain output) Pin not connected. Output, TTL compatible. Output, open-collector or open-drain, TTL compatible. Output with tri-state capability, TTL compatible. Low Voltage Differential Signal. Power supply or ground reference pins. Ioh: Typical current in mA flowing out of an output pin through a grounded load, while the output voltage is > 2.4 V DC (if nothing else stated). Iol: Typical current in mA flowing into an output pin from a VCC connected load, while the output voltage is < 0.4 V DC (if nothing else stated). Pull U/D On-board pull-up or pull-down resistors on input pins or open-collector output pins. Note Special remarks concerning the signal. The abbreviation TBD is used for specifications which are not available yet or which are not sufficiently specified by the component vendors. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 30 IO-Area Connectors 5 IO-Area Connectors 5.1 Display connectors (IO Area) The KTQM77 provides one on-board DVI-I port (both digital and analogue), two on-board DP's (DisplayPort), one on-board eDP (Embedded DisplayPort) and one on-board LVDS panel interface. Two graphic pipes are supported; meaning that up to two independent displays can be implemented using any two of the above mentioned graphic ports. 5.1.1 DVI Connector (DVI-I) (J41) The DVI-I connector support DVI Digital output and DVI Analogue output. Female socket, front view Signal Description - DVI Connector: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 C6 Signal TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield NC NC DDC Clock DDC Data NC TMDS Data 1TMDS Data 1+ TMDS Data 1/3 Shield NC NC +5V GND Hot Plug Detect TMDS Data 0TMDS Data 0+ TMDS Data 0/5 Shield NC NC TMDS Clock Shield TMDS Clock+ TMDS ClockANALOG RED ANALOG GREEN ANALOG BLUE ANALOG HSYNC ANALOG GND ANALOG GND Description Digital Red - (Link 1) Digital Red + (Link 1) DDC Clock DDC Data Digital Green - (Link 1) Digital Green + (Link 1) Power for monitor when in standby Hot Plug Detect Digital Blue - (Link 1) / Digital sync Digital Blue + (Link 1) / Digital sync Digital clock + (Link 1) Digital clock - (Link 1) Analog output carrying the red color signal Analog output carrying the green color signal Analog output carrying the blue color signal CRT horizontal synchronization output. Ground reference for RED, GREEN, and BLUE Ground reference for RED, GREEN, and BLUE Type Pull U/D LVDS OUT LVDS OUT PWR NC NC IO 2K2 IO 2K2 NC LVDS OUT LVDS OUT PWR NC NC PWR PWR I LVDS OUT LVDS OUT PWR NC NC PWR LVDS OUT LVDS OUT O /75R O /75R O /75R O PWR PWR Note: The +5V supply is fused by a 1.1A resettable fuse KTQM77 - KTHM76 Users Guide KTD-N0850-F 5.1.2 Page 31 IO-Area Connectors DP Connectors (DP0/DP1) (J40/J39) The DP (DisplayPort) connectors are based on standard DP type Foxconn 3VD51203-H7JJ-7H or similar. 19 20 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Config1 14 Config2 16 17 18 19 20 18 15 16 Signal Description Lane 0 (p) GND Lane 0 (n) Lane 1 (p) GND Lane 1 (n) Lane 2 (p) GND Lane 2 (n) Lane 3 (p) GND Lane 3 (n) 13 15 17 Aux or DDC selection (Not used) Aux Channel (+) Aux Ch (p) or DDC Clk GND Aux Channel (-) Aux Ch (n) or DDC Data Hot Plug Return 3.3V 13 14 11 12 9 10 7 8 5 6 3 4 1 2 Type Note LVDS PWR LVDS LVDS PWR LVDS LVDS PWR LVDS LVDS PWR LVDS Internally pull down (1Mohm). I Aux channel on pin 15/17 selected as default (when NC) DDC channel on pin 15/17, If HDMI adapter used (3.3V) O Internally connected to GND AUX (+) channel used by DP DDC Clk used by HDMI PWR AUX (-) channel used by DP DDC Data used by HDMI I Internally pull down (100Kohm). PWR Same as GND Fused by 1.5A resetable PTC fuse, common for DP0 and PWR DP1 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 32 IO-Area Connectors 5.2 Ethernet Connectors The KTQM77/mITX supports three channels of 10/100/1000Mb Ethernet, one (ETH1) is based on Intel(R) Lewisville 82579LM Gigabit PHY with AMT 8.0 support and the two other controllers (ETHER2 & ETHER3) are based on Intel(R) Hartwell 82574L PCI Express controller. The KTHM76/mITX support one channels of 10/100/1000Mb Ethernet, (ETH1) based on Intel(R) Lewisville 82579LM Gigabit PHY (AMT not supported). In order to achieve the specified performance of the Ethernet port, Category 5 twisted pair cables must be used with 10/100MB and Category 5E, 6 or 6E with 1Gb LAN networks. The signals for the Ethernet ports are as follows: Signal Description MDI[0]+ / MDI[0]- In MDI mode, this is the first pair in 1000Base-T, i.e. the BI_DA+/- pair, and is the transmit pair in 10Base-T and 100Base-TX. In MDI crossover mode, this pair acts as the BI_DB+/- pair, and is the receive pair in 10Base-T and 100Base-TX. MDI[1]+ / MDI[1]- In MDI mode, this is the second pair in 1000Base-T, i.e. the BI_DB+/- pair, and is the receive pair in 10Base-T and 100Base-TX. In MDI crossover mode, this pair acts as the BI_DA+/- pair, and is the transmit pair in 10Base-T and 100Base-TX. MDI[2]+ / MDI[2]- In MDI mode, this is the third pair in 1000Base-T, i.e. the BI_DC+/- pair. In MDI crossover mode, this pair acts as the BI_DD+/- pair. MDI[3]+ / MDI[3]- In MDI mode, this is the fourth pair in 1000Base-T, i.e. the BI_DD+/- pair. In MDI crossover mode, this pair acts as the BI_DC+/- pair. Note: MDI = Media Dependent Interface. Ethernet connector 1 (ETH1) is mounted together with USB Ports 4 and 5. Ethernet connector 2 (ETH2) is mounted together with and above Ethernet connector 3 (ETH3) (KTQM77/mITX only). The pinout of the RJ45 connectors is as follows: Signal MDI0+ MDI0MDI1+ MDI2+ MDI2MDI1MDI3+ MDI3- PIN 8 7 6 5 4 Type 3 2 Ioh/Iol Note 1 KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 33 IO-Area Connectors 5.3 USB Connectors (IO Area) The KTQM77 board contains two EHCI (Enhanced Host Controller Interface) and one XHCI (Extensible Host Controller Interface). The two EHCI controllers, EHCI1 and EHCI2, supports up to fourteen USB 2.0 ports allowing data transfers up to 480Mb/s. The XHCI controller supports four USB 3.0 ports allowing data transfers up to 5Gb/s. The four USB 3.0 ports are shared with four of the USB 2.0 ports (USB0 - USB3) from the EHCI1. Legacy Keyboard/Mouse and wakeup from sleep states are supported. Over-current detection on all fourteen USB ports is supported. The following USB connectors are available in the IO Area. USB Port 0 and 1 (via EHCI1/XHCI) are supplied on the combined USB0, USB1 and DP0 connector. USB Port 2 and 3 (via EHCI1/XHCI) are supplied on the combined USB2, USB3 and DP1 connector. USB Port 4 and 5 (via EHCI1) are supplied on the combined ETH1, USB4 and USB5 connector. Note: For USB2.0 cabling it is required to use only HiSpeed USB cable, specified in USB2.0 standard: For USB3.0 cabling it is required to use only HiSpeed USB cable, specified in USB3.0 standard: KTQM77 - KTHM76 Users Guide KTD-N0850-F 5.3.1 Page 34 IO-Area Connectors USB Connector 0/1 (USB0/1) USB Ports 0 and 1 are mounted together with DP0 port and supports USB3.0/USB2.0. Note 1 1 Type Signal PIN Signal Type IO PWR IO IO PWR USB1- USB1+ 5V/SB5V 1 2 3 4 GND RX1- 5 6 7 8 9 TX1+ RX1+ TX1GND IO PWR IO IO IO PWR IO IO PWR USB0- USB0+ 5V/SB5V 1 2 3 4 GND RX0- 5 6 7 8 9 TX0+ RX0+ TX0GND IO PWR IO IO Note Note 1: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Signal USB0+ USB0RX0+ RX0TX0+ TX0USB1+ USB1RX1+ RX1TX1+ TX15V/SB5V Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 2A fuse covering both USB ports. KTQM77 - KTHM76 Users Guide KTD-N0850-F 5.3.2 Page 35 IO-Area Connectors USB Connector 2/3 (USB2/3) USB Ports 2 and 3 are mounted together with DP1 port and supports USB3.0/USB2.0. Note Type 1 1 Signal PIN Signal Type IO PWR IO IO PWR USB3- USB3+ 5V/SB5V 1 2 3 4 GND RX3- 5 6 7 8 9 TX3+ RX3+ TX3GND IO PWR IO IO IO PWR IO IO PWR USB2- USB2+ 5V/SB5V 1 2 3 4 GND RX2- 5 6 7 8 9 TX2+ RX2+ TX2GND IO PWR IO IO Note Note 1: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Signal USB2+ USB2RX2+ RX2TX2+ TX2USB3+ USB3RX3+ RX3TX3+ TX35V/SB5V 5.3.3 Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 2A fuse covering both USB ports. USB Connector 4/5 (USB4/5) USB Ports 4 and 5 are mounted together with ETH1 port and supports USB2.0. Note Type Signal PIN 1 PWR IO 5V/SB5V USB5- 1 2 3 1 PWR IO 5V/SB5V USB4- 1 2 3 Signal Type 4 GND USB5+ PWR IO 4 GND USB4+ PWR IO Note Note 1: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Signal USB4+ USB4USB5+ USB55V/SB5V Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 1A fuse covering both USB ports. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 36 IO-Area Connectors 5.4 Audio Connector (IO Area) The on-board Audio circuit implements 7.1+2 Channel High Definition Audio with UAA (Universal Audio Architecture), featuring five 24-bit stereo DACs and three 20-bit stereo ADCs. The Following Audio connector is available in IO Area. Audio Speakers, Line-in and Microphone are available in the stacked audiojack connector. Signal TIP RING SLEEVE TIP RING SLEEVE LINE1-L LINE1-R GND IA IA PWR FRONT-OUT-L OA FRONT-OUT-R OA GND PWR TIP RING SLEEVE Signal Type Note MIC1-L MIC1-R GND IA IA PWR Description Note FRONT-OUT-L Front Speakers (Speaker Out Left). FRONT-OUT-R Front Speakers (Speaker Out Right). MIC1-L Microphone 1 - Left Shared with Audio Header MIC1-R Microphone 1 - Right Shared with Audio Header LINE1-L Line 1 signal - Left Shared with Audio Header LINE1-R Line 1 signal - Right Shared with Audio Header KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 37 Internal Connectors 6 Internal Connectors 6.1 Power Connector (ATX/BTXPWR) The KTQM77 boards are designed to be supplied from a standard ATX (or BTX) power supply. Alternatively supplied by single +12V +/-5%. Use of BTX supply is not required for operation, but may be required to drive high-power PCIe cards. ATX/ BTX Power Connector (J43): Note Type PWR PWR PWR PWR I PWR PWR PWR PWR PWR PWR PWR Signal 3V3 +12V +12V SB5V P_OK GND 5V GND 5V GND 3V3 3V3 PIN 12 24 11 23 10 22 9 21 8 20 7 19 6 18 5 17 4 16 3 15 2 14 1 13 Signal GND 5V 5V 5V -5V GND GND GND PSON# GND -12V 3V3 Type PWR PWR PWR PWR PWR PWR PWR PWR OC PWR PWR PWR Note 1 Note 1: -5V supply is not used on-board. See chapter "Power Consumption" regarding input tolerances on 3.3V, 5V, SB5V, +12 and -12V (also refer to ATX specification version 2.2). ATX+12V-4pin Power Connector (J42): Note Type PWR PWR Signal GND GND 2 1 PIN 4 3 Signal +12V +12V Type PWR PWR Note 1 1 Note 1: Use of the 4-pin ATX+12V Power Connector is required for operation of KTQM77. Signal P_OK PS_ON# Description P_OK is a power good signal and should be asserted high by the power supply to indicate that the +5VDC and +3.3VDC outputs are above the undervoltage thresholds of the power supply. When this signal is asserted high, there should be sufficient energy stored by the converter to guarantee continuous power operation within specification. Conversely, when the output voltages fall below the undervoltage threshold, or when mains power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, P_OK should be de-asserted to a low state. The recommended electrical and timing characteristics of the P_OK (PWR_OK) signal are provided in the ATX12V Power SupplyDesign Guide. It is strongly recommended to use an ATX or BTX supply, in order to implement the supervision of the 5V and 3V3 supplies. These supplies are not supervised on-board. Active low open drain signal from the board to the power supply to turn on the power supply outputs. Signal must be pulled high by the power supply. Warning: Hot Plugging power supply is not supported. Hot plugging might damage the board. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 38 Internal Connectors 6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29) The FAN_CPU is used for the connection of the FAN for the CPU. The FAN_SYS can be used to power, control and monitor a fan for chassis ventilation etc. The 4pin header is recommended to be used for driving 4-wire type Fan in order to implement FAN speed control. 3-wire Fan is also possible, but no fan speed control is integrated. 4-pin Mode: PIN 1 2 3 4 Signal CONTROL SENSE Signal Type Ioh/Iol CONTROL SENSE +12V GND O I PWR PWR - Pull U/D 4K7 - Note Description PWM signal for FAN speed control Tacho signal from the fan for supervision. The signals shall be generated by an open collector transistor or similar. On-board is a pull-up resistor 4K7 to +12V. The signal has to be pulsed, typically twice per rotation. 12V +12V supply for fan. A maximum of 2000mA can be supplied from this pin. GND Power Supply GND signal 3-pin Mode: PIN Signal Type Ioh/Iol 2 3 4 Pull U/D SENSE +12V GND I PWR PWR - 4K7 - Note Signal Description SENSE Tacho signal from the fan for supervision. The signals shall be generated by an open collector transistor or similar. On-board is a pull-up resistor 4K7 to +12V. The signal has to be pulsed, typically twice per rotation. 12V +12V supply for fan. A maximum of 2000mA can be supplied from this pin. GND Power Supply GND signal KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 39 Internal Connectors 6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J27) Attachment of a PS/2 keyboard/mouse can be done through the pinrow connector KBDMSE (J27). Both interfaces utilize open-drain signalling with on-board pull-up. The PS/2 mouse and keyboard is supplied from SB5V when in standby mode in order to enable keyboard or mouse activity to bring the system out from power saving states. The supply is provided through a 1.1A resettable fuse. PIN 1 2 3 4 5 6 Signal Type Ioh/Iol KBDCLK KBDDAT MSCLK MSDAT 5V/SB5V GND IOD IOD IOD IOD PWR PWR /14mA /14mA /14mA /14mA - Pull U/D 2K7 2K7 2K7 2K7 - Note Signal Description - Keyboard & and mouse Connector (KBDMSE). Signal Description MSCLK Bi-directional clock signal used to strobe data/commands from/to the PS/2 mouse. MSDAT Bi-directional serial data line used to transfer data from or commands to the PS/2 mouse. KDBCLK Bi-directional clock signal used to strobe data/commands from/to the PC-AT keyboard. KBDDAT Bi-directional serial data line used to transfer data from or commands to the PC-AT keyboard. Available cable kit: PN 1053-2384 Bracket Cable 6-Pin to PS2-Kbd-Mse KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 40 Internal Connectors 6.4 Display connectors (Internal) The KTQM77 provides internal display connectors: one on-board LVDS panel interface and one onboard eDP (Embedded DisplayPort) (KTQM77/mITX only). LVDS and eDP and cannot be used at the same time. For IO Area Display Connectors (DVI-I and two DP's), see earlier section. 6.4.1 eDP connector (EDP) (J38) The eDP connector (KTQM77/mITX only) is based on single in-line 40 pole connector type TYCO 52069716-3. Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NC BL-VCC BL-VCC BL-VCC BL-VCC NC NC BL-PWM BL-EN BL-GND BL-GND BL-GND BL-GND HPD LCD-GND LCD-GND LCD-GND LCD-GND NC LCD-VCC LCD-VCC LCD-VCC LCD-VCC GND Aux (n) Aux (p) GND Lane 0 (p) Lane 0 (n) GND Lane 1 (p) Lane 1 (n) GND Lane 2 (p) Lane 2 (n) GND Lane 3 (p) Lane 3 (n) GND NC Description Type Note NC PWR PWR Backlight Voltage PWR PWR NC NC Back Light PWM (Pulse Width Modulated) O Back Light Enable O PWR PWR Backlight GND PWR PWR Hot Plug Detection I PWR PWR Display panel GND PWR PWR NC PWR PWR Display panel voltage PWR PWR PWR LVDS LVDS PWR LVDS LVDS PWR LVDS LVDS PWR LVDS LVDS PWR LVDS LVDS PWR NC Fused by 1.5A resetable PTC fuse 12V (in S0 mode) To adjust Back Light intensity To enable the Back Light Shared with LVDS connector 3.3V or 5V selected in BIOS Fused by 1.5A resetable PTC fuse KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.4.2 Page 41 Internal Connectors LVDS Flat Panel Connector (LVDS) (J20) The LVDS connector is based on 40 pole connector type Don Connex C44-40BSB1-G. Note Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A 2K2, 3.3V 3.3V level 3.3V level Max. 0.5A Max. 0.5A Note: Type Signal PWR +12V PWR +12V PWR +12V PWR +5V PWR LCDVCC OT DDC CLK OT BKLTCTL OT BKLTEN# LVDS LVDS A0LVDS LVDS A1LVDS LVDS A2LVDS LVDS ACLKLVDS LVDS A3PWR GND LVDS LVDS B0LVDS LVDS B1LVDS LVDS B2LVDS LVDS BCLKLVDS LVDS B3PWR GND PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Signal +12V +12V GND GND LCDVCC DDC DATA VDD ENABLE GND LVDS A0+ LVDS A1+ LVDS A2+ LVDS ACLK+ LVDS A3+ GND LVDS B0+ LVDS B1+ LVDS B2+ LVDS BCLK+ LVDS B3+ GND Type PWR PWR PWR PWR PWR OT OT PWR LVDS LVDS LVDS LVDS LVDS PWR LVDS LVDS LVDS LVDS LVDS PWR Note Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A 2K2, 3.3V 3.3V level Max. 0.5A Max. 0.5A Max. 0.5A The KTQM77 on-board LVDS connector supports single and dual channel, 18/24bit SPWG panels up to the resolution 1600x1200 or 1920x1080 and with limited frame rate some 1920x1200. Signal Description - LVDS Flat Panel Connector: Signal LVDS A0..A3 LVDS ACLK LVDS B0..B3 LVDS BCLK BKLTCTL BKLTEN# VDD ENABLE LCDVCC DDC CLK Description LVDS A Channel data LVDS A Channel clock LVDS B Channel data LVDS B Channel clock Backlight control (1), PWM signal to implement voltage in the range 0-3.3V Backlight Enable signal (active low) (2) Output Display Enable. VCC supply to the display. Power-on/off sequencing depending on selected (in BIOS setup) display type. 5V or 3.3V selected in BIOS setup. LCDVCC is shared with eDP connector. Maximum load is 1A at both voltages. DDC Channel Clock Notes: Windows API will be available to operate the BKLTCTL signal. Some Inverters have a limited voltage range 0- 2.5V for this signal: If voltage is > 2.5V the Inverter might latch up. Some Inverters generates noise on the BKLTCTL signal, resulting in making the LVDS transmission failing (corrupted picture on the display). By adding a 1Kohm resistor in series with this signal, mounted in the Inverter end of the cable kit, the noise is limited and the picture is stable. If the Backlight Enable is required to be active high then, check the following BIOS Chipset setting: Backlight Signal Inversion = Enabled. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 42 Internal Connectors 6.5 SATA (Serial ATA) Disk interface (J21 - J26) The KTQM77 has an integrated SATA Host controller (PCH in the QM77 chipset) that supports independent DMA operation on six ports. One device can be installed on each port for a maximum of six SATA devices. A point-to-point interface (SATA cable) is used for host to device connections. Data transfer rates of up to 6.0Gb/s (typically 600MB/s) on SATA0 and SATA1 and 3.0Gb/s (typically 300MB/s) on SATA2, SATA3, SATA4 and SATA5. SATA2 is shared with mPCIe0. Note: Before installing OS on a SATA drive make sure the drive is not a former member of a RAID system. If so some hidden data on the disk has to be erased. To do this, connect two SATA drives and select RAID in BIOS. Save settings and select <Ctrl> <I> while booting to enter the RAID setup menu. Now the hidden RAID data will be erased from the selected SATA drive. The SATA controller supports: RAID (Redundant Array of Independent Drives) based on a firmware system (KTQM77/mITX only): 2 to 6-drive RAID 0 (data striping) 2-drive RAID 1 (data mirroring) 3 to 6-drive RAID 5 (block-level striping with parity) 4-drive RAID 10 (data striping and mirroring) 2 to 6-drive matrix RAID, parts of a single drive can be assigned to different RAIDs AHCI (Advanced Host Controller Interface) NCQ (Native Command Queuing). NCQ is for faster data access. Hot Swap Intel(R) Rapid Recover Technology 2 - 256TB volume (Data volumes only) Capacity expansion TRIM in Windows 7 (in AHCI and RAID mode for drives not part of a RAID volume). (TRIM is for SSD data garbage handling). SATA connector pinning: SATA0 (J21), SATA1 (J22), SATA2 (J23), SATA3 (J24), SATA4 (J25) and SATA5 (J26). Signal PIN Signal Type Ioh/Iol Pull U/D 1 2 3 4 5 6 7 GND SATA* TX+ SATA* TXGND SATA* RXSATA* RX+ GND PWR - - PWR - - PWR - - Note Description SATA* RX+ SATA* RX- Host transmitter differential signal pair SATA* TX+ SATA* TX- Host receiver differential signal pair "*" specifies 0, 1, 2, 3, 4, 5 depending on SATA port. Available cable kit: PN 821035 Cable SATA 500mm KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 43 Internal Connectors 6.6 USB Connectors (USB) The KTQM77 board contains two EHCI (Enhanced Host Controller Interface) host controllers (EHCI1 and EHCI2) that support up to fourteen USB 2.0 ports allowing data transfers up to 480Mb/s. Legacy Keyboard/Mouse and wakeup from sleep states are supported. Over-current detection on all fourteen USB ports is supported. Note that four USB 3.0 ports are shared with four of the USB 2.0 ports (USB0 - USB3) from the EHCI1. The following USB ports are available on Internal Pinrows: USB Port 6 and 7 (KTQM77/mITX only) (via EHCI1) are supplied on the USB6/7 internal pinrow FRONTPNL connector. USB Port 8 and 9 (via EHCI2) are supplied on the USB8/9 internal pinrow connector. USB Port 10 and 11 (via EHCI2) are supplied on the USB10/11 internal pinrow connector. USB Port 12 and 13 (via EHCI2) are supplied on the USB12/13 internal pinrow connector. Note: It is required to use only HiSpeed USB cable, specified in USB2.0 standard: 6.6.1 Connector Definitions USB Connector 6/7 See Frontpanel Connector (FRONTPNL) description (KTQM77/mITX only). 6.6.2 USB Connector 8/9 (USB8/9) (J10) USB Ports 8 and 9 are supplied on the internal USB8/9 pinrow connector J10. Note Type Signal 1 PWR 5V/SB5V IO USB8IO USB8+ PWR GND NC KEY Signal USB8+ USB8USB9+ USB95V/SB5V PIN 1 2 3 4 5 6 7 8 9 10 Signal Type Note 5V/SB5V PWR 1 USB9IO USB9+ IO GND PWR NC NC Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 1A fuse covering both USB ports. KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.6.3 Page 44 Internal Connectors USB Connector 10/11 (USB10/11) (J11) USB Ports 10 and 11 are supplied on the internal USB10/11 pinrow connector J11. Note Type Signal 1 PWR 5V/SB5V IO USB10IO USB10+ PWR GND NC KEY Signal USB10+ USB10USB11+ USB115V/SB5V 6.6.4 PIN 1 2 3 4 5 6 7 8 9 10 Signal Type Note 5V/SB5V PWR 1 USB11IO USB11+ IO GND PWR NC NC Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 1A fuse covering both USB ports. USB Connector 12/13 (USB12/13) (J12) USB Ports 12 and 13 are supplied on the internal USB12/13 pinrow connector J12. Note Type Signal 1 PWR 5V/SB5V IO USB12IO USB12+ PWR GND NC KEY Signal USB12+ USB12USB13+ USB135V/SB5V PIN 1 2 3 4 5 6 7 8 9 10 Signal Type Note 5V/SB5V PWR 1 USB13IO USB13+ IO GND PWR NC NC Description Differential pair works as Data/Address/Command Bus. 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 1A fuse covering both USB ports. Note 1: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Available cable kit: PN 821401 Bracket Dual USB Cable KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 45 Internal Connectors 6.7 Firewire/IEEE1394 connectors (J13,J14) The KTQM77/mITX (only) support two IEEE Std 1394a-2000 fully compliant ports at 100M bits/s, 200M bits/s and 400M bits/s. 6.7.1 IEEE1394 connector (IEEE1394_0) (J14) Note 1 key Pull Ioh/Iol Type Signal PIN U/D TPA0+ 1 2 PWR GND 3 4 TPB0+ 5 6 PWR +12V 7 8 NC 9 10 Signal Type Ioh/Iol TPA0GND PWR TPB0+12V PWR GND PWR - Pull Note U/D 1 - Note 1: The 12V supply for the IEEE1394_0 devices is on-board fused with a 1.25A reset-able fuse. 6.7.2 Signal Description TPA0+,TPA0- Differential signal pair A TPB0+, TPB0- +12V Differential signal pair B +12V supply IEEE1394 connector (IEEE1394_1) (J13) Note 1 key Pull Ioh/Iol Type Signal PIN U/D TPA0+ 1 2 PWR GND 3 4 TPB0+ 5 6 PWR +12V 7 8 NC 9 10 Signal Type Ioh/Iol TPA0GND PWR TPB0+12V PWR GND PWR - Pull Note U/D 1 - Note 1: The 12V supply for the IEEE1394_1 devices is on-board fused with a 1.25A reset-able fuse. Signal Description TPA1+, TPA1- Differential signal pair A TPB1+, TPB1- +12V Differential signal pair B +12V supply KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 46 Internal Connectors 6.8 Serial COM1 - COM4 Ports (J15, J16, J17, J18) Four RS232 serial ports are available on the KTQM77. The typical definition of the signals in the COM ports is as follows: Signal Description TxD Transmitted Data, sends data to the communications link. The signal is set to the marking state (-12V) on hardware reset when the transmitter is empty or when loop mode operation is initiated. RxD Received Data, receives data from the communications link. DTR Data Terminal Ready, indicates to the modem etc. that the on-board UART is ready to establish a communication link. DSR Data Set Ready, indicates that the modem etc. is ready to establish a communications link. RTS Request To Send, indicates to the modem etc. that the on-board UART is ready to exchange data. CTS Clear To Send, indicates that the modem or data set is ready to exchange data. DCD Data Carrier Detect, indicates that the modem or data set has detected the data carrier. RI Ring Indicator, indicates that the modem has received a ringing signal from the telephone line. The pinout of Serial ports COM1 (J15), COM2 (J16), COM3 (J17) and COM4 (J18) is as follows: Note Ioh/Iol Type Signal I DCD I RxD O TxD O DTR PWR GND PIN 1 2 3 4 5 6 7 8 9 10 Signal Type Ioh/Iol Note DSR I RTS O CTS I RI I 5V PWR 1 Note 1: The COM1, COM2, COM3 and COM4 5V supply is fused with common 1.1A resettable fuse. DB9 adapter cables (PN 821016 200mm long and 821017 100mm long) are available for implementing standard COM ports on chassis. Available cable kit (DB9 adapter cables): PN 821017 - 100 mm or PN 821016 - 200 mm KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 47 Internal Connectors 6.9 Audio Connectors The on-board Audio circuit implements 7.1+2 Channel High Definition Audio with UAA (Universal Audio Architecture), featuring five 24-bit stereo DACs and three 20-bit stereo ADCs. The following Audio connectors are available as Internal connectors. 6.9.1 CDROM Audio Input (CDROM) (J3) CD-ROM audio input may be connected to this connector or it can be used as secondary line-in signal. PIN 1 2 3 4 Signal CD_Left CD_GND CD_GND CD_Right Type IA IA IA IA Note 1 1 Note 1: The definition of which pins are used for the Left and Right channels is not a worldwide accepted standard. Some CDROM cable kits expect reverse pin order. Signal Description CD_Left CD_Right Left and right CD audio input lines or secondary Line-in. CD_GND Analogue GND for Left and Right CD. (This analogue GND is not shorted to the general digital GND on the board). 6.9.2 Line2 and Mic2 Line2 and Mic2 are accessible via Feature Connector, see Feature connector description. KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.9.3 Page 48 Internal Connectors Audio Header Connector (AUDIO_HEAD) (J31) Note Type Signal AO LFE-OUT PWR AAGND 1 AO FRONT-OUT-L PWR AAGND AO REAR-OUT-L AO SIDE-OUT-L PWR AAGND 1 AI MIC1-L PWR AAGND 1 LINE1-L NC NC PWR GND O SPDIF-OUT PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Signal CEN-OUT AAGND FRONT-OUT-R AAGND REAR-OUT-R SIDE-OUT-R AAGND MIC1-R AAGND LINE1-R AAGND NC GND Type Note AO PWR AO 1 PWR AO AO PWR AI 1 PWR 1 PWR NC PWR Note 1: Shared with Audio Stack connector Signal Description FRONT-OUT-L Front Speakers (Speaker Out Left). FRONT-OUT-R Front Speakers (Speaker Out Right). REAR-OUT-L Rear Speakers (Surround Out Left). REAR-OUT-R Rear Speakers (Surround Out Right). SIDE-OUT-L Side speakers (Surround Out Left) SIDE-OUT-R Side speakers (Surround Out Right) CEN-OUT Center Speaker (Center Out channel). LFE-OUT Subwoofer Speaker (Low Freq. Effect Out). NC No connection MIC1 MIC Input 1 LINE1 Line 1 signals F-SPDIF-OUT S/PDIF Output AAGND Audio Analogue ground Available cable kit: PN 821043 Cable, Audio Open-End (300 mm) KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.9.4 Page 49 Internal Connectors Front Panel Connector (FRONTPNL) (J19) Note 1 1 Pull Ioh/ Type Signal U/D Iol PWR USB6/7_5V USB6USB6+ PWR GND NC NC PWR +5V - 25/25mA O SATA_LED# PWR GND 4K7 I RSTIN# PWR SB3V3 PWR AGND AI MIC2-L Ioh/ Pull Note Iol U/D USB6/7_5V PWR USB71 USB7+ 1 GND PWR LINE2-L +5V PWR SUS_LED O 7mA PWRBTN_IN# I 1K1 GND PWR LINE2-R AGND PWR MIC2-R AI - PIN 1 3 5 7 9 11 13 15 17 19 21 23 Signal 2 4 6 8 10 12 14 16 18 20 22 24 Type Note 1: USB 6 / 7 only supported by KTQM77/mITX. Signal USB6/7_5V Description 5V supply for external devices. SB5V is supplied during powerdown to allow wakeup on USB device activity. Protected by resettable 1.1A fuse covering both USB ports. USB6+/USB6- Universal Serial Bus Port 6 Differentials: Bus Data/Address/Command Bus. USB7+/USB7- Universal Serial Bus Port 7 Differentials: Bus Data/Address/Command Bus. +5V Maximum load is 1A or 2A per pin if using IDC connector flat cable or crimp terminals respectively. SATA_LED# SATA Activity LED (active low signal). 3V3 output when passive. SUS_LED Suspend Mode LED (active high signal). Output 3.3V via 470. PWRBTN_IN# Power Button In. Toggle this signal low to start the ATX / BTX PSU and boot the board. RSTIN# Reset Input. When pulled low for a minimum 16ms, the reset process will be initiated. The reset process continues even though the Reset Input is kept low. LINE2 Line2 is second stereo Line signals MIC2 MIC2 is second stereo microphone input. SB3V3 Standby 3.3V voltage AGND Analogue Ground for Audio Note: In order to meet the requirements of USB standard, the 5V input supply must be at least 5.00V. Available cable kit: PN 821042 Cable Front Panel Open-End, 300 mm KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.10 Note 2 Page 50 Internal Connectors Feature Connector (FEATURE) (J30) Pull U/D 2M/ - Ioh/Iol 25/25mA 25/25mA - - 8/8mA 8/8mA - Type Signal I CASE_OPEN# O S5# O PWR_OK O FAN3OUT PWR SB3V3 IOT GPIO0 IOT GPIO2 IOT GPIO4 IOT GPIO6 PWR GND I GPIO8 I GPIO10 I GPIO12 IOT GPIO14 IOT GPIO16 PWR GND O EGCLK EGAD PWR +12V O FAN4OUT PWR GND PWR GND PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Signal 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 SMBC SMBD EXT_BAT FAN3IN SB5V GPIO1 GPIO3 GPIO5 GPIO7 GND GPIO9 GPIO11 GPIO13 GPIO15 GPIO17 GND EGCS# TMA0 GND FAN4IN GND S3# Type Ioh/Iol /4mA /4mA - PWR I PWR IOT IOT IOT IOT PWR I I IOT IOT IOT PWR O 8/8mA O PWR I PWR O 25/25mA Pull U/D 10K/ 10K/ - Note 1 1 - Notes: 1. Pull-up to +3V3Dual (+3V3 or SB3V3). 2. Pull-up to on-board Battery. 3. Pull-up to +3V3. Available cable kit: PN 1052-5885 Cable, Feature 44pol 1 to1, 300mm KTQM77 - KTHM76 Users Guide KTD-N0850-F Signal Page 51 Internal Connectors SMBC Description CASE OPEN, used to detect if the system case has been opened. This signal's status is readable, so it may be used like a GPI when the Intruder switch is not required. SMBus Clock signal SMBD SMBus Data signal CASE_OPEN# S3# S3 sleep mode, active low output, optionally used to deactivate external system. S5# S5 sleep mode, active low output, optionally used to deactivate external system. PoWeR OK, signal is high if no power failures are detected. (This is not the same as the P_OK signal generated by ATX PSU). (EXTernal BATtery) option for connecting + terminal of an external primary cell battery (2.5 - 4.0 V) (- terminal connected to GND). The external battery is protected against charging and can be used with/without the on-board battery installed. FAN 3 speed control OUTput, 3.3V PWM signal can be used as Fan control voltage. PWR_OK EXT_BAT FAN3OUT FAN3IN FAN4OUT FAN3 Input. 0V to +3V3 amplitude Fan 3 tachometer input. FAN 4 speed control OUTput, 3.3V PWM signal can be used as Fan control voltage. FAN4IN FAN4 Input. 0V to +3V3 amplitude Fan 3 tachometer input. SB3V3 Max. load is 0.75A (1.5A < 1 sec.) SB5V EGCLK StandBy +5V supply. General Purpose Inputs / Output. These Signals may be controlled or monitored through the use of the KT-API-V2 (Application Programming Interface). Extend GPIO Clock signal EGAD Extend GPIO Address Data signal EGCS# Extend GPIO Chip Select signal, active low GPIO0..17 TMA0 Timer Output +12V Max. load is 0.75A (1.5A < 1 sec.) Available Temperature Sensor cable kit (for System Fan Temperature Cruise, selected in BIOS): Based on Maxim DS18B20, Accurate to 0.5C over the range of -10C to +85C Feature connector 3.3V (Pin 9), GND (Pin 19) and GPIO16 (Pin 29) PN1053-4925 Cable Temperature Sensor - 44P, 400 mm KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 52 Internal Connectors GPIO in more details. The GPIO's are controlled via the ITE IT8516F Embedded Controller. Each GPIO has 100pF to ground, clamping Diode to 3V3 and has multiplexed functionality. Some pins can be DAC (Digital to Analogue Converter output), PWM (Pulse Width Modulated signal output), ADC (Analogue to Digital Converter input), TMRI (Timer Counter Input), WUI (Wake Up Input), RI (Ring Indicator Input) or some special function. Signal IT8516F pin name Type GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8 GPIO9 GPIO10 GPIO11 GPIO12 GPIO13 GPIO14 GPIO15 GPIO16 GPIO17 DAC0/GPJ0 DAC1/GPJ1 DAC2/GPJ2 DAC3/GPJ3 PWM2/GPA2 PWM3/GPA3 PWM4/GPA4 PWM5/GPA5 ADC0/GPI0 ADC1/GPI1 ADC2/GPI2 ADC3/GPI3 ADC4/WUI28/GPI4 RI1#/WUI0/GPD0 RI2#/WUI1/GPD1 TMRI0/WUI2/GPC4 TMRI1/WUI3/GPC6 L80HLAT/BAO/WUI24/GPE0 AO/IOS AO/IOS AO/IOS AO/IOS O8/IOS O8/IOS O8/IOS O8/IOS AI/IS AI/IS AI/IS AI/IS AI/IS/IS IS/IS/IOS IS/IS/IOS IS/IS/IOS IS/IS/IOS O4/O4/IS/IOS Description Feature Break-out board: PN 820978 Feature BOB (Break-Out-Board) KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.11 Page 53 Internal Connectors "Load Default BIOS Settings" Jumper (J37) The "Load Default BIOS Settings" Jumper (J37) can be used to recover from incorrect BIOS settings. As an example, incorrect BIOS settings coursing no display to turn on can be erased by the Jumper. The Jumper has 3 positions: Pin 1-2, Pin2-3 (default position) and not mounted. Jumper (in default position) ! Warning Don't leave the jumper in position 1-2, otherwise if power is disconnected, the battery will fully deplete within a few weeks. J37 pin 1 BIOS version 12 and above: J37 pin1-2 pin2-3 X X - Description Don't use. (Board do not boot with jumper in this position) Default position Load Default BIOS Settings and erase Password To Load Default BIOS Settings, inclusive erasing password: 1. Turn off power completely (no SB5V). 2. Remove the Jumper completely from J37. 3. Turn on power. 4. Motherboard beeps fast 20 times and turns off. 5. Turn off power. 6. Move the Jumper back to position 2-3 (default position). 7. Turn on power (use the Power On Button if required to boot). Motherboard might automatically reboot a few times. Wait until booting is completed. BIOS version below 12: pin1-2 X - J37 pin2-3 X - Description Load Default BIOS Settings exclusive erasing Password Default position No function To Load Default BIOS Settings, exclusive erasing Password and RTC: 1. Turn off power completely (no SB5V). 2. Move the Jumper to pin 1-2 for ~10 seconds. 3. Move the Jumper back to position 2-3 (default position). 4. Turn on power (use the Power On Button if required to boot). 5. Motherboard might automatically reboot a few times. Wait until booting is completed. KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.12 Page 54 Internal Connectors SPI Recover Jumper (J4) The SPI Recover Jumper (J4) is used to select BIOS Recovery Flash instead of BIOS Default Flash. By default the J4 is not installed. It is recommended that Jumper is plugged to J4 only in case the Default BIOS is corrupted, so that board is malfunctioning and do not boot, or the Recovery BIOS is requested to be upgraded in order to have sufficient or same support as the default BIOS. In case Default BIOS seems corrupted then it is recommend to first trying to use the Load Default BIOS Settings Jumper, see previous page. When using customised BIOS it is recommended to upgrade both the Default BIOS and the Recovery BIOS with the Customised BIOS. Recover corrupted Default BIOS procedure: 1. 2. 3. 4. 5. 6. 7. 8. Turn off power. Install "SPI Recover Jumper"(J4). Reboot. Remove "SPI Recover Jumper". Upgrade the BIOS (fx. execute Upd.bat, containing: BF safewrite xxxxxx.xxx). When BIOS upgrade is completed then turn off power completely (inclusive Standby +5V). Wait minimum 10 seconds. Turn on power. System will automatically reboot 4-5 times within 1 minute. Upgrade Recovery BIOS procedure: 1. 2. 3. 4. 5. 6. 7. Reboot. Install "SPI Recover Jumper"(J4). Upgrade the BIOS (fx. execute UpdRec.bat, containing: BF safewrite xxxxxx.xxx RECOVERY). When BIOS upgrade is completed then turn off power completely (inclusive Standby +5V). Wait minimum 10 seconds. Turn on power. System will automatically reboot 4-5 times within 1 minute. If boot succeed then remove "SPI Recover Jumper". Upgrade first Default BIOS and then Recovery BIOS with Customised BIOS procedure: 1. Reboot. 2. Upgrade the BIOS (fx. execute Upd.bat). 3. When BIOS upgrade is completed then turn off power completely (inclusive Standby +5V). 4. Wait minimum 10 seconds. 5. Turn on power. System will automatically reboot 4-5 times within 1 minute. 6. Install "SPI Recover Jumper"(J4). 7. Upgrade the BIOS (fx. execute UpdRec.bat). 8. When BIOS upgrade is completed then turn off power completely (inclusive Standby +5V). 9. Wait minimum 10 seconds. 10. Turn on power. System will automatically reboot 4-5 times within 1 minute. 11. Remove "SPI Recover Jumper". Note: It is not recommended to upgrade both Default BIOS and Recovery BIOS without rebooting and verification in between, unless you are sure that BIOS and tools works correctly. Otherwise there is a risk that both BIOS will be corrupted at the same time with the result that board cannot be recovered. KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.13 Page 55 Internal Connectors SPI Connector (SPI) (J5) The SPI Connector is normally not used. If however a SPI BIOS is connected via the SPI Connector then the board will try to boot on it. Note Pull U/D Ioh/Iol Type Signal CLK I CS0# 10K/ NC 10K/ IO MOSI IO MISO Signal Description CLK Serial Clock SB3V3 PIN Signal Type Ioh/Iol Pull U/D Note 1 2 SB3V3 PWR 3 4 ADDIN IO /10K 5 6 NC 7 8 ISOLATE# IO 100K 9 10 GND PWR - 3.3V Standby Voltage power line. Normally output power, but when Motherboard is turned off then the on-board SPI Flash can be 3.3V power sourced via this pin. CS0# CS0# Chip Select 0, active low. ADDIN ADDIN input signal must be NC. MOSI Master Output, Slave Input ISOLATE# MISO The ISOLATE# input, active low, is normally NC, but must be connected to GND when loading SPI flash. Power Supply to the Motherboard must be turned off when loading SPI flash. The pull up resistor is connected via diode to 5VSB. Master Input, Slave Output KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.14 Page 56 Internal Connectors XDP-CPU (Debug Port for CPU) (J32) The XDP-CPU (Intel Debug Port for CPU) connector is not mounted and not supported. XDP connector layout (pads) is located on the backside of PCB and is prepared for the Molex 52435-2671 (or 524352672). Pin Signal 1 OBSFN_A0 2 OBSFN_A1 3 GND 4 NC 5 NC 6 GND 7 NC 8 NC 9 GND 10 HOOK0 11 HOOK1 12 HOOK2 13 HOOK3 14 HOOK4 15 HOOK5 16 +5V 17 HOOK6 18 HOOK7 19 GND 20 TDO 21 TRST# 22 TDI 23 TMS 24 NC 25 GND 26 TCK0 Description Type Pull Up/Down PWR NC NC PWR NC NC PWR - PWR - PWR NC PWR 500R /51R /51R /51R /51R /51R Note (500R by 2x1K in parallel) KTQM77 - KTHM76 Users Guide KTD-N0850-F 6.15 Page 57 Internal Connectors XDP-PCH (Debug Port for Chipset) (J33) The XDP-PCH (Intel Debug Port for Chipset) connector is not mounted and not supported. XDP-PCH connector layout (pads) is located on the backside of PCB (below J35 connector on mITX version) and is prepared for the Molex 52435-2671 (or 52435-2672). Pin Signal Description Type Pull Up/Down 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 NC NC GND NC NC GND NC NC GND HOOK0 HOOK1 HOOK2 HOOK3 HOOK4 HOOK5 +5V HOOK6 HOOK7 GND TDO TRST# TDI TMS NC GND TCK0 NC NC PWR NC NC PWR NC NC PWR Note - RSMRST# PWRBTN# Connected to HOOK6 NC NC NC NC PWR - PWR 500R 210R/100R RESET# NC PWR Connected to HOOK1 (500R by 2x1K in parallel) 210R/100R 210R/100R /51R KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 58 Slot Connectors 7 Slot Connectors (PCIe, miniPCIe, PCI) 7.1 PCIe Connectors All members of the KTQM77 family supports one (x16) (16-lane) PCI Express port, one x1 PCI Express port and two miniPCI Express ports. The 16-lane (x16) PCI Express (PCIe 2.0 and PCIe 3.0) port can be used for external PCI Express cards inclusive graphics card. It is located nearest the CPU. Maximum theoretical bandwidth using 16 lanes is 16 GB/s. PCIe x1, PCIe x2, PCIe x4, PCIe x8 and PCIe x16 are supported; however PCIe x2 is only supported when using 3rd generation Intel(R) CoreTM processor (Ivy Bridge). The two miniPCIe (PCIe 2.0) is located on the backside of the board. The 1-lane (x1) PCI Express (PCIe 2.0) can be used for any PCIex1 cards inclusive "Riser PCIex1 to PCI Dual flexible card". 7.1.1 Note PCI-Express x16 Connector (PCIe x16) Type Signal +12V +12V +12V GND SMB_CLK SMB_DATA GND +3V3 NC SB3V3 WAKE# PIN B1 A1 B2 A2 B3 A3 B4 A4 B5 A5 B6 A6 B7 A7 B8 A8 B9 A9 B10 A10 B11 A11 NC GND PEG_TXP[0] PEG_TXN[0] GND CLKREQ GND PEG_TXP[1] PEG_TXN[1] GND GND PEG_TXP[2] PEG_TXN[2] GND GND PEG_TXP[3] PEG_TXN[3] GND NC CLKREQ GND PEG_TXP[4] PEG_TXN[4] GND B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 Signal NC +12V +12V GND NC NC NC NC +3V3 +3V3 RST# Type Note GND PCIE_x16 CLK PCIE_x16 CLK# GND PEG_RXP[0] PEG_RXN[0] GND NC GND PEG_RXP[1] PEG_RXN[1] GND GND PEG_RXP[2] PEG_RXN[2] GND GND PEG_RXP[3] PEG_RXN[3] GND NC NC GND PEG_RXP[4] KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 59 GND PEG_TXP[5] PEG_TXN[5] GND GND PEG_TXP[6] PEG_TXN[6] GND GND PEG_TXP[7] PEG_TXN[7] GND CLKREQ GND PEG_TXP[8] PEG_TXN[8] GND GND PEG_TXP[9] PEG_TXN[9] GND GND PEG_TXP[10] PEG_TXN[10] GND GND PEG_TXP[11] PEG_TXN[11] GND GND PEG_TXP[12] PEG_TXN[12] GND GND PEG_TXP[13] PEG_TXN[13] GND GND PEG_TXP[14] PEG_TXN[14] GND GND PEG_TXP[15] PEG_TXN[15] GND CLKREQ NC B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 Slot Connectors PEG_RXN[4] GND GND PEG_RXP[5] PEG_RXN[5] GND GND PEG_RXP[6] PEG_RXN[6] GND GND PEG_RXP[7] PEG_RXN[7] GND NC GND PEG_RXP[8] PEG_RXN[8] GND GND PEG_RXP[9] PEG_RXN[9] GND GND PEG_RXP[10] PEG_RXN[10] GND GND PEG_RXP[11] PEG_RXN[11] GND GND PEG_RXP[12] PEG_RXN[12] GND GND PEG_RXP[13] PEG_RXN[13] GND GND PEG_RXP[14] PEG_RXN[14] GND GND PEG_RXP[15] PEG_RXN[15] GND KTQM77 - KTHM76 Users Guide KTD-N0850-F 7.1.2 Page 60 Slot Connectors miniPCI-Express mPCIe0 (J34) The miniPCI Express port mPCIe0 is located on the backside. Beside miniPCIe cards the mPCIe0 also supports mSATA SSD cards. SATA2 is used for mSATA signals. Note: no USB signals are available. Note Type 1 NC NC PWR PWR NC NC PWR PWR PWR PWR PWR PWR PWR PWR 3 Signal WAKE# NC NC CLKREQ# GND PCIE_mini CLK# PCIE_mini CLK GND NC NC GND PCIE_RXN PCIE_RXP GND GND PCIE_TXN PCIE_TXP GND GND +3V3 Dual +3V3 Dual GND CLK_MPCIE DATA_MPCIE RST_MPCIE# SEL_MSATA PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal +3V3 GND +1.5V NC NC NC NC NC Type PWR PWR PWR NC NC NC NC NC GND W_Disable# RST# +3V3 Dual GND +1.5V SMB_CLK SMB_DATA GND NC NC GND NC NC NC +1.5V GND +3V3 Dual PWR Note 2 PWR PWR PWR PWR NC NC PWR NC NC NC PWR PWR PWR Note 1: 10K ohm pull-up to 3V3. Note 2: 2K2 ohm pull-up to 3V3 Dual. Note 3: 100K ohm pull-up to 1V8 (S0 mode) KTQM77 - KTHM76 Users Guide KTD-N0850-F 7.1.3 Page 61 Slot Connectors miniPCI-Express mPCIe1 (J35) The miniPCI Express port mPCIe1 is located on the backside. Note: no USB and no mSATA signals are available. Note Type 1 NC NC PWR PWR NC NC PWR PWR PWR PWR NC NC NC NC NC NC NC NC Signal WAKE# NC NC CLKREQ# GND PCIE_mini CLK# PCIE_mini CLK GND NC NC GND PCIE_RXN PCIE_RXP GND GND PCIE_TXN PCIE_TXP GND NC NC NC NC NC NC NC NC PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 Signal +3V3 GND +1.5V NC NC NC NC NC Type PWR PWR PWR NC NC NC NC NC GND W_Disable# RST# +3V3 Dual GND +1.5V SMB_CLK SMB_DATA GND NC NC GND NC NC NC +1.5V GND +3V3 PWR Note 2 PWR PWR PWR PWR NC NC PWR NC NC NC PWR PWR PWR Note 1: 10K ohm pull-up to 3V3 Dual. Note 2: 2K2 ohm pull-up to 3V3 Dual. KTQM77 - KTHM76 Users Guide KTD-N0850-F 7.1.4 Page 62 Slot Connectors PCI-Express x1 Connector (PCIe x1) (J36) Connector Definitions The KTQM77/mITX supports one PCIe x1. Note Type PWR PWR PWR PWR 2 PWR PWR PWR NC PWR 1 PWR PWR Signal +12V +12V +12V GND SMB_CLK SMB_DATA GND +3V3 JTAG_TEST# 3V3 Dual WAKE# NC GND PCIE_TXP PCIE_TXN GND CLK_REQ GND PIN B1 A1 B2 A2 B3 A3 B4 A4 B5 A5 B6 A6 B7 A7 B8 A8 B9 A9 B10 A10 B11 A11 B12 B13 B14 B15 B16 B17 B18 A12 A13 A14 A15 A16 A17 A18 Signal GND +12V +12V GND NC NC NC NC +3V3 +3V3 RST# Type PWR PWR PWR PWR GND PCIE_CLK_P PCIE_CLK_N GND PCIE_RXP PCIE_RXN GND PWR Note PWR PWR PWR PWR Note 1: 10K ohm pull-up to 3V3 Dual. Note 2: 4K7 ohm pull-down to GND. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 63 Onboard/mating connector 8 On-board - & mating connector types The Mating connectors / Cables are connectors or cable kits which are fitting the On-board connector. The highlighted cable kits are included in the "KTQM67 Cable & Driver Kit" PN 826598, in different quantities depending on type of connector. For example there is 4 x 821017 COM cables and 6 x 821035 SATA cables. Connector FAN_CPU FAN_SYS KBDMSE On-board Connectors Manufacturer Type no. Foxconn HF2704E-M1 AMP 1470947-1 Molex 22-23-2061 Foxconn Molex Hon Hai HF1104E 70543-0038 LD1807V-S52T ATXPWR ATX+12V-4pin Molex Lotes 44206-0002 ABA-POW-003-K02 EDP Tyco Don Connex 5-2069716-3 C44-40BSB1-G Wuerth 61201020621 Pinrex CDROM Mating Connectors / Cables Manufacturer Type no. AMP 1375820-4 (4-pole) AMP 1375820-3 (3-pole) Molex 22-01-2065 KT 1046-3381 Kontron KT 1053-2384 Molex 50-57-9404 Molex Kontron Molex Molex 67489-8005 KT 821035 (cable kit) 5557-24R 39-01-2045 Tyco Don Connex Kontron Kontron Kontron Molex Kontron Kontron 2023344-3 A32-40-C-G-B-1 KT 910000005 KT 821515 (cable kit) KT 821155 (cable kit) 90635-1103 KT 821016 (cable kit) KT 821017 (cable kit) 512-90-10GBB2 Kontron KT 821401 (cable kit) (FRONTPNL) - Kontron KT 821401 (cable kit) AUDIO_HEAD Foxconn Molex HS1105F-RNP9 87831-2620 FRONTPNL Pinrex 512-90-24GBB3 FEATURE Foxconn HS5422F Kontron Molex Kontron Molex Kontron Don Connex KT 821040 (cable kit) 51110-2651 KT 821043 (cable kit) 90635-1243 KT 821042 (cable kit) A05c-44-B-G-A-1-G SATA LVDS COM1,2, 3, 4 USB68/9, 10/11, 12/13 USB6/7 (*) IEEE1394_0/1 * USB6/USB7 is located in FRONTPNL connector. Depending on application KT 821401 can be used. Notes: Only one connector will be mentioned for each type of on-board connector even though several types with same fit, form and function are approved and could be used as alternative. Please also notice that standard connectors like DVI, DP, PCIe, miniPCIe, Audio Jack, Ethernet and USB is not included in the list. The KTHM76/mITX do not support: EDP, USB6/7 and IEEE1394_0/1. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 64 System Resources 9 System Resources 9.1 Memory Map Address (hex) Size (hex) 0xFF000000 0xFFFFFFFF 1000000 0xFEE00000 0xFED90000 0xFED45000 0xFED40000 0xFED20000 0xFED1C000 0xFED19000 0xFED18000 0xFED10000 0xFED00000 0xF8000000 0xF7F3B000 0xF7F39000 0xF7F38000 0xF7F37000 0xF7F36000 0xF7F35000 0xF7F30000 0xF7F00000 0xF7E00000 0xF7D00000 0xF7C00000 0xF7800000 0xE0000000 0xFEEFFFFF 0xFED93FFF 0xFED8FFFF 0xFED44FFF 0xFED3FFFF 0xFED1FFFF 0xFED19FFF 0xFED18FFF 0xFED17FFF 0xFED003FF 0xFBFFFFFF 0xF7F3B00F 0xF7F39FFF 0xF7F383FF 0xF7F373FF 0xF7F367FF 0xF7F350FF 0xF7F33FFF 0xF7F1FFFF 0xF7EFFFFF 0xF7DFFFFF 0xF7CFFFFF 0xF7BFFFFF 0xEFFFFFFF 100000 4000 4B000 5000 20000 4000 1000 1000 8000 400 4000000 10 1000 400 400 800 100 4000 20000 100000 100000 100000 400000 10000000 0xDFA00000 0xDFA00FFF 1000 0x40000000 0x20000000 0xE4000 0xE0000 0xDC000 0xD8000 0xD4000 0xD0000 0x401FFFFF 0x201FFFFF 0xE7FFF 0xE3FFF 0xDFFFF 0xDBFFF 0xD7FFF 0xD3FFF 200000 200000 4000 4000 4000 4000 4000 4000 0xA0000 0xBFFFF 20000 Description Intel(R) 82802 Firmware Hub Device Motherboard resources Motherboard resources Motherboard resources Motherboard resources System board Motherboard resources Motherboard resources Motherboard resources Motherboard resources Motherboard resources High Precision Event Timer Motherboard resources Intel(R) Management Engine Interface Intel(R) 82579LM Gigabit Network Intel(R) Chipset USB EHCI - 1E2D Intel(R) Chipset USB EHCI - 1E26 Intel(R) Chipset 6 port SATA ACHI - 1E03 Intel(R) Chipset SMBus Controller - 1E22 High Definition Audio Controller Intel(R) 82579LM Gigabit Network Intel(R) Chipset PCIe Root port 3 - 1E14 Intel(R) Chipset PCIe Root port 4 - 1E16 Intel(R) Chipset PCIe Root port 6 - 1E1A Intel(R) HD Graphics 4000 Family Intel(R) HD Graphics 4000 Family Motherboard resources PCI bus System board System board PCI bus PCI bus PCI bus PCI bus PCI bus PCI bus Intel(R) HD Graphics Family PCI bus KTQM77 - KTHM76 Users Guide IRQ NMI IRQ0 X IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ20 IRQ21 IRQ22 IRQ23 IRQ24 IRQ25 IRQ26 X X X X X X X X X X X X X X Intel(R) USB EHCI - 1E26 Page 65 High Definition Audio Intel(R) SATA ACHI - 1E03 X Intel(R) PCIe Root Port 4 - 1E16 Intel(R) PCIe Root Port 3 - 1E14 LSI 1394 OHCI Host X Intel(R) PCIe Root Port 6 - 1E1A Intel(R) Management Engine Interface X Intel(R) PCIe Root Port 1 - 1E10 X Intel(R) USB EHCI - 1E2D Numerical Data Processor PS2 Mouse Intel(R) SMBus -1E22 COM3 Selection in BIOS System CMOS/real-time watch COM4 Selection in BIOS COM1 Selection in BIOS COM2 Selection in BIOS PS/2 Keyboard System timer KTD-N0850-F System Resources 9.3 Interrupt Usage Notes X KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 66 System Resources 9.4 IO Map Address range (hex) 0x0000FFFF 0x0000FFFF 0x0000F0D0 0x0000F0D7 0x0000F0C0 0x0000F0C3 0x0000F0B0 0x0000F0B7 0x0000F0A0 0x0000F0A3 0x0000F060 0x0000F07F 0x0000F040 0x0000F05F 0x0000F000 0x0000F03F 0x0000E000 0x0000EFFF 0x0000D000 0x0000DFFF 0x0000164E 0x0000164F 0x00001000 0x0000100F 0x00000F78 0x00000F7F 0x00000B78 0x00000B7F 0x00000A00 0x00000A2F 0x00000778 0x0000077F 0x00000680 0x0000069F 0x00000500 0x0000057F Size (hex) 1 8 4 8 4 20 20 40 1000 1000 2 10 8 8 30 8 20 80 0x000004D0 0x000004D1 2 0x00000458 0x00000454 0x00000400 0x000003F8 0x000003E8 0x000003C0 0x000003B0 0x00000378 0x000002F8 0x000002E8 0x00000290 0x0000020E 0x000000F0 0x000000E0 0x000000C0 0x000000A2 0x000000A0 0x00000081 0x00000072 0x00000070 0x00000067 0x00000065 0x00000064 0x00000063 0x00000061 0x00000060 0x00000044 0x00000040 0x00000022 0x00000022 0x00000020 0x0000047F 0x00000457 0x00000453 0x000003FF 0x000003EF 0x000003DF 0x000003BB 0x0000037F 0x000002FF 0x000002EF 0x0000029F 0x0000020F 0x000000FF 0x000000EF 0x000000DF 0x000000BF 0x000000A1 0x00000091 0x00000080 0x00000077 0x00000067 0x00000065 0x00000064 0x00000063 0x00000061 0x00000060 0x0000005F 0x00000043 0x0000003F 0x00000023 0x00000021 28 4 54 8 8 20 C 8 8 8 10 2 10 10 20 1E 2 10 E 8 1 1 1 1 1 1 1C 4 1E 2 2 0x00000000 0x0000001F 20 Description Motherboard resources Intel(R) 7 port SATA AHCI - 1E03 Intel(R) 7 port SATA AHCI - 1E03 Intel(R) 7 port SATA AHCI - 1E03 Intel(R) 7 port SATA AHCI - 1E03 Intel(R) 7 port SATA AHCI - 1E03 Intel(R) SMBus - 1E22 Intel(R) HD Graphics 4000 family Intel(R) PCIe Root port 3 - 1E14 Intel(R) PCIe Root port 4 - 1E16 Motherboard resources Motherboard resources Motherboard resources Motherboard resources Motherboard resources Motherboard resources Motherboard resources Motherboard resources Programmable interrupt controller Motherboard resources Motherboard resources Motherboard resources Motherboard resources COM1 COM4 Intel(R) HD Graphics 4000 family Intel(R) HD Graphics 4000 family Printer port LPT1 COM2 COM3 Motherboard resources Motherboard resources Numeric data processor Motherboard resources Direct memory access controller Motherboard resources Programmable interrupt controller Direct memory access controller Motherboard resources System CMOS/real time clock Motherboard resources Motherboard resources Standard PS/2 Keyboard Motherboard resources Motherboard resources Standard PS/2 Keyboard Motherboard resources System Timer Motherboard resources Motherboard resources Programmable interrupt controller Direct memory access controller PCI bus KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 67 BIOS - Main 10 BIOS The BIOS Setup is used to view and configure BIOS settings for the board. The BIOS Setup is accessed by pressing the <Del> -key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. The BIOS settings will be loaded automatically when loading Restore Default see Save & Exit menu. In this Users Guide the default settings are indicated by bold. Please notice that Restore User Defaults might have different set of default values. 10.1 Main Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliancy BIOS Version Build Date and Time EC Firmware Version American Megatrends 4.6.5.3 UEFI 2.3; PI 1.2 15 12/19/2013 07:42:40 V1.21 07/05/13 Board Information Product Name PCB ID Serial # Part # Boot Count KTQM77/mITX 00 01092087 64800000 452 System Date System Time [Mon 12/30/2013] [11:30:40] Access Level Administrator Set the Date. Use Tab to switch between Date elements. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Blue text for settings that can be changed. White text for actual setting to be changed via the control keys (Black text for settings that cannot be changed via control keys) Note: Product Name is KTHM76/mITX or KTQM77/mITX depending on actual board type. The following table describes the changeable settings: Feature System Date System Time Options MM/DD/YYYY HH:MM:SS Description Set the system date. Set the system time. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2 Page 68 BIOS - Advanced Advanced Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit PCI Subsystem ACPI Settings Settings Trusted Computing CPU Configuration SATA Configuration Intel TXT (LT) Configuration AMT Configuration Acoustic Management Configuration USB Configuration SMART Settings Super IO Configuration Voltage Monitor Hardware Health Configuration Displayblock Setup LAN Configuration Delay Startup Serial Port Console Redirection CPU PPM Configuration PCI, PCI-X and PCI Express Settings. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: the submenus Intel TXT (LT) Configuration and AMT Configuration are only present when using KTQM77/mITX. The Advanced (main) menu contains only submenu selections which will be described in more details on the following pages. In order to make a selection of a submenu activated the keys until the requested submenu becomes white color, then activate the <Enter>. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 69 BIOS - Advanced 10.2.1 Advanced - PCI Subsystem Settings Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced PCI Bus Driver Version V 2.05.02 PCI 64bit Resources Handling Above 4G Decoding [Disabled] PCI Express Settings PCI Express GEN 2 Settings Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address Space (Only if System Supports 64 bit PCI Decoding). : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Above 4G Decoding Disabled Enabled Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address Space (Only if System Supports 64 bit PCI Decoding). Note: The selection in bold is the default selection. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 70 BIOS - Advanced 10.2.1.1 PCI Express Settings Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced PCI Express Link Register Settings Set the ASPM Level: Force L0s - Force all links to L0s State: Auto - BIOS auto configure: Disable - Disabled ASPM ASPM Support [Disabled] WARNING: Enabling ASPM may cause Some PCI-E devices to fail : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description ASPM Support Disabled Auto Force L0s Set the ASPM Level: Force L0s - Force all links to L0s State. Auto - BIOS auto configure Disable - Disabled ASPM KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 71 BIOS - Advanced 10.2.1.2 PCI Express GEN 2 Settings Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced PCI Express GEN2 Link Register Settings Target Link Speed If supported by hardware and set to `Force to 2.5GT/s' for Downstream Ports, this sets an upper limit on Link operational speed by restricting the values advertised by the Upstream component in its training sequences. Ehen `Auto' is selected HW initialized data will be used. [Auto] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Target Link Speed Selection Description Auto Force to 2.5GT/s Force to 5.0GT/s If supported by hardware and set to `Force to 2.5GT/s' for Downstream Ports, this sets an upper limit on Link operational speed by restricting the values advertised by the Upstream component in its training sequences. Ehen `Auto' is selected HW initialized data will be used. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 72 BIOS - Advanced 10.2.2 Advanced - APCI Settings Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced ACPI Settings Enables or Disables BIOS APCI Auto Configuration. Enable ACPI Auto Configuration [Disabled] Enable Hibernation ACPI Sleep State [Enabled] [Both S1 and S3 ava...] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Enable ACPI Auto Configuration Disabled Enabled Enables or Disables BIOS APCI Auto Configuration. Enable Hibernation Disabled Enabled Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Suspend Disabled S1 only(CPU Stop Clock) S3 only(Suspend to RAM) Both S1 and S3 available For OS to choose from Select ACPI sleep state the system will enter when the SUSPEND button is pressed. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 73 BIOS - Advanced 10.2.3 Advanced - Trusted Computing Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Configuration Security Device Support TPM State Pending operation [Enable] [Enabled] [None] Current Status Information TPM Enabled Status: TPM Active Status: TPM Owner Status: [Disabled] [Deactivated] [Unowned] Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Security Device Support Disabled Enabled Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. TPM State Disabled Enabled Enable/Disable Security Device. NOTE: Your Computer will reboot during restart in order to change State of the Device. Pending operation None Enable Take Ownership Disable Take Ownership TPM Clear Schedule an Operation for the Security Device. NOTE: Your Computer will reboot during restart in order to change State of the Device. Note: TPM State and Pending operation are only visible if Security Device Support is Enabled followed by Save and Exit. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 74 BIOS - Advanced 10.2.4 Advanced - CPU Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced CPU Configuration Intel(R) CoreTM i5-3610ME CPU @ CPU Signature Microcode Patch Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT-x Technology Intel SMX Technology 64-bit 2.70GHz 306a8 10 2700 MHz 1200 MHz 2700 MHz 2 Supported Supported Supported Supported L1 Data Cache L1 Code Cache L2 Cache L3 Cache 32 kB x 2 32 kB x 2 256 kB x 2 3072 kB Hyper-threading Active Processor Cores Limit CPUID Maximum Execute Disable Bit Intel Virtualization Technology [Enabled] [All] [Disabled] [Enabled] [Disabled] Enabled for Windows XP and Linux (OS optimized for HyperThreading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Disabled Enabled Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled. Active Processor Cores All 1 Number of cores to enable in each processor package. Limit CPUID Maximum Disabled Enabled Disabled for Windows XP Execute Disable Bit Disabled Enabled XD can prevent certain classes of malicious buffer overflow attacks when combined with supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.) Intel Virtualization Technology Disabled Enabled When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Hyper-threading (Note1) Note1: Not present when using Intel Celeron B810. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 75 BIOS - Advanced Notes: Intel HT Technology (Hyper Threading Technology) is a performance feature which allows one core on the processor to appear like 2 cores to the operating system. This doubles the execution resources available to the O/S, which potentially increases the performance of your overall system. Intel VT-x Technology (Virtualization Technology) Previously codenamed "Vanderpool", VT-x represents Intel's technology for virtualization on the x86 platform. In order to support "Virtualization Technology" the CPU must support VT-x and the BIOS setting "Intel Virtualization Technology" must be enabled. Intel SMX Technology (Safer Mode Extensions Technology) is a part of the Trusted Execution Technology. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 76 BIOS - Advanced 10.2.5 Advanced - SATA Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced SATA Controller(s) [Enabled] SATA Mode Selection [ACHI] SATA Controller Speed [Gen3] Software Feature Mask Configuration Serial ATA Port 0 Software Preserve Port 0 Hot Plug External SATA SATA Device Type Spin Up Device Serial ATA Port 1 Software Preserve Port 1 Hot Plug External SATA SATA Device Type Spin Up Device Serial ATA Port 2 Software Preserve Port 2 Hot Plug External SATA Spin Up Device Enable or Disable SATA Device. ST3120827AS (120. NOT SUPPORTED [Enabled] [Disabled] [Disabled] [Hard Disk Driver] [Disabled] Empty Unknown [Enabled] [Disabled] [Disabled] [Hard Disk Driver] [Disabled] Empty Unknown [Enabled] [Disabled] [Disabled] [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc (Scroll indicator bar) Note: By scrolling down (or up) also settings for Serial ATA Port 3 - 5 can be accessed. Function Selection Description SATA Controller(s) Disabled Enabled Enable or Disable SATA Device. SATA Mode Selection IDE ACHI RAID Determines how SATA controller(s) operate. RAID is supported by the KTQM77/mITX only. SATA Controller Speed Gen1 Gen2 Gen3 Indicates the maximum speed the SATA controller can support. Note: in the above BIOS menu the functions below the submenu Software Feature Mask Configuration will be described after the submenu description. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 77 BIOS - Advanced 10.2.5.1 Software Feature Mask Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced RAID0 RAID1 RAID10 RAID5 Intel Rapid Recovery Technology OROM UI and BANNER HDD Unlock LED Locate IRRT Only on eSATA Smart Response Technology OROM UI Delay [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [2 Seconds] Enables or Disables RAID0 feature. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 78 BIOS - Advanced Submenu Software Feature Mask Configuration description: Function Selection Description RAID0 Disabled Enabled Enable or disable RAID0 feature. RAID1 Disabled Enabled Enable or disable RAID1 feature. RAID10 Disabled Enabled Enable or disable RAID10 feature. RAID5 Disabled Enabled Enable or disable RAID5 feature. Intel Rapid Recovery Technology Disabled Enabled Enable or disable Intel Rapid Recovery Technology. OROM UI and BANNER Disabled Enabled If enabled, then the OROM UI is shown. Otherwise, no OROM banner or information will be displayed if all disks and RAID volumes are Normal. HDD Unlock Disabled Enabled If enabled, indicates that the HDD password unlock in the OS is enabled. LED Locate Disabled Enabled If enabled, indicates that the LED/SGPIO hardware is attached and ping to locate feature is enabled on the OS. IRRT Only on eSATA Disabled Enabled If enabled, then only IRRT volumes can span internal and eSATA drives. If disabled, then any RAID volume can span internal and eSATA drives. Smart Response Technology Disabled Enabled Enable or disable Smart Response Technology OROM UI Delay 2 Seconds 4 Seconds 6 Seconds 8 Seconds If enabled, indicates the delay of the OROM UI Splash Screen in normal status. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 79 BIOS - Advanced Remaining SATA Configuration menu description: Function Selection Description Port 0 Disabled Enabled Enable or Disable SATA Port. Hot Plug Disabled Enabled Designates this port as Hot Pluggable. External SATA Disabled Enabled External SATA Support. SATA Device Type Hard Disk Drive Solid State Drive Identify the SATA port is connected to Solid State Drive or Hard Disk Drive. Spin Up Device Disabled Enabled On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device. Port 1 Disabled Enabled Enable or Disable SATA Port. Hot Plug (see same function above) (see same function above) External SATA (see same function above) (see same function above) SATA Device Type (see same function above) (see same function above) Spin Up Device (see same function above) (see same function above) Port 2 Disabled Enabled Enable or Disable SATA Port. Hot Plug (see same function above) (see same function above) External SATA (see same function above) (see same function above) Spin Up Device (see same function above) (see same function above) Port 3 Disabled Enabled Enable or Disable SATA Port. Hot Plug (see same function above) (see same function above) External SATA (see same function above) (see same function above) Spin Up Device (see same function above) (see same function above) Port4 Disabled Enabled Enable or Disable SATA Port. Hot Plug (see same function above) (see same function above) External SATA (see same function above) (see same function above) Spin Up Device (see same function above) (see same function above) Port5 Disabled Enabled Enable or Disable SATA Port. Hot Plug (see same function above) (see same function above) External SATA (see same function above) (see same function above) Spin Up Device (see same function above) (see same function above) KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 80 BIOS - Advanced 10.2.6 Advanced - Intel TXT (LT) Configuration Intel TXT (LT) Configuration is only present when using KTQM77/mITX. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT. Secure Mode Extensions (SMX) Enabled Intel TXT support [Disabled] Enables or Disables Intel (R) TXT (LT) support. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc SMX (Intel Secure Mode Extension) instructions are enabled if supported by the CPU, so no BIOS settings are present. VT (Intel Virtualization Technology) is enabled/disabled in the menu: Advanced > CPU Configuration. VT-d can be enabled/disabled in the menu: Chipset > System Agent (SA) Configuration. Function Selection Description Intel TXT support Disabled Enabled Enables or Disables Intel (R) TXT (LT) support. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 81 BIOS - Advanced 10.2.7 Advanced - AMT Configuration AMT Configuration is only present when using KTQM77/mITX. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Intel AMT BIOS Hotkey Pressed MEBx Selection Screen Hide Un-Configure ME Confirmation MEBx Debug Message Output Un-Configure ME AMT Wait Timer Disable ME ASF Active Remote Assistance Process USB Configure PET Progress AMT CIRA Timeout Watchdog OS Timer BIOS Timer [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] 0 [Disabled] [Enabled] [Disabled] [Enabled] [Enabled] 0 [Disabled] 0 0 Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS Extension execution. If enabled, this requires additional firmware in the SPI device. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Intel AMT Disabled Enabled Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS Extension execution. If enabled, this requires additional firmware in the SPI device. BIOS Hotkey Pressed (Note1) Disabled Enabled OEMFlag Bit 1: Enable/Disabled BIOS hotkey press. MEBx Selection Screen (Note1) Disabled Enabled OEMFlag Bit 2: Enable/Disabled BIOS MEBx Selection Screen. Hide Un-Configure ME Confirmation (Note1) Disabled Enabled OEMFlag Bit 6: Hide Un-Configure ME without password Confirmation Prompt MEBx Debug Message Output (Note1) Disabled Enabled OEMFlag Bit 14: Enable MEBx Debug Message Output. Un-Configure ME (Note1) Disabled Enabled OEMFlag Bit 15: Un-Configure ME without password. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 82 BIOS - Advanced Function Selection Description AMT Wait Timer (Note1) 0 - 65535 Disable ME (Note1) Disabled Enabled Set ME to Soft Temporary Disabled. ASF (Note1) Disabled Enabled Enable/Disabled Alert Specification Format. Active Remote Assistance Process (Note1) Disabled Enabled Trigger CIRA boot. USB Configure (Note1) Disabled Enabled Enable/Disable USB Configure function. PET Progress (Note1) Disabled Enabled Users can Enable/Disable PET Events progress to receive PET events or not. AMT CIRA Timeout (Note1) (Note5) 0 - 255 OEM defined timeout for MPS connection to be established. 0 - use the default timeout value of 60 seconds. 255 - MEBX waits until the connection succeeds. Watchdog (Note2) Disabled Enabled OS Timer (Note3) 0 - 65535 (Note4) Set OS watchdog timer. BIOS Timer (Note3) 0 - 65535 (Note4) Set BIOS Watchdog Timer. (Note4) (Note4) Set timer to wait before sending ASF_GET_BOOT_OPTIONS. Enable/Disable Watchdog Timer. Note1: Only if Intel AMT = Enabled. Note2: This Watchdog function is unsupported. Recommendation, use Watchdog function present in Hardware Health Configuration menu. Note3: Only if Watchdog = Enabled. Note4: To enter number use digit keys and/or +/- keys. Note5: Only if Active Remote Assistance Process = Enabled. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 83 BIOS - Advanced 10.2.8 Advanced - Acoustic Management Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Acoustic Management Configuration Option to Enable or Disable Automatic Acoustic Management Automatic Acoustic Management [Disabled] Sata Port 0 ST3120827AS Acoustic Mode [Not Available] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Automatic Acoustic Management Enabled Disabled Option to Enable or Disable Automatic Acoustic Management. Note: Automatic acoustic management (AAM) is a method for reducing acoustic emanations in AT Attachment (ATA) mass storage devices, such as ATA hard disk drives and ATAPI optical disc drives. AAM is an optional feature set for ATA/ATAPI devices; when a device supports AAM, the acoustic management parameters are adjustable through a software or firmware user interface. The ATA/ATAPI sub-command for setting the level of AAM operation is an 8-bit value from 0 to 255. Most modern drives ship with the vendor-defined value of 0x00 in the acoustic management setting. This often translates to the max-performance value of 254 stated in the standard. Values between 128 and 254 (0x80 - 0xFE) enable the feature and select most-quiet to most-performance settings along that range. Though hard drive manufacturers may support the whole range of values, the settings are allowed to be banded so many values could provide the same acoustic performance. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 84 BIOS - Advanced 10.2.9 Advanced - USB Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced USB Configuration USB Module Version 8.10.28 USB Devices: 2 Hubs Legacy USB Support USB3.0 Support XHCI Hand-off EHCI Hand-off USB Mass Storage Driver Support Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] USB hardware delays and time-outs: USB transfer time-out [20 sec] Device reset time-out [20 sec] Device power-up delay [Auto] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 85 BIOS - Advanced Function Selection Description Legacy USB Support Enabled Disabled Auto Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. USB3.0 Support Enabled Disabled Enable/Disable USB3.0 (XHCI) Controller support. XHCI Hand-off Enabled Disabled This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. EHCI Hand-off Enabled Disabled This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. USB Mass Storage Driver Support USB transfer time-out Device reset time-out Device power-up delay Enabled Disabled 1 sec 5 sec 10 sec 20 sec 10 sec 20 sec 30 sec 40 sec Auto Normal Enable/disable USB Mass Storage Driver Support. The time-out value for Control, Bulk, and Interrupt transfers. USB mass storage device Start Unit command time-out. Maximum time the device will take before it properly reports itself to the Host Controller. `Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 86 BIOS - Advanced 10.2.10 Advanced - SMART Settings Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced SMART Settings SMART Self Test Run SMART Self Test on all HDDs during POST. [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description SMART Self Test Disabled Enabled Run SMART Self-Test on all HDDs during POST. Note: S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology; often written as SMART) is a monitoring system for computer hard disk drives to detect and report on various indicators of reliability, in the hope of anticipating failures. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 87 BIOS - Advanced 10.2.11 Advanced - Super IO Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Super IO Configuration Super IO Chip Port 1 Configuration Port 2 Configuration IT8516F Super IO Chip W83627H Serial Serial Serial Port 3 Configuration Serial Port 4 Configuration Parallel Port Configuration Set Parameters of Serial Port 1 (COMA) : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: Parallel Port is not available (connector not mounted). The 5 submenus are shown and described on the following pages. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.11.1 Page 88 BIOS - Advanced Serial Port 1 Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Serial Port 1 Configuration Serial Port Device Settings [Enabled] IO=3F8h; IRQ=4; Change Settings [Auto] Enable or Disable Serial Port (COM) : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Auto IO=3F8h; IRQ=4; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Super IO device. Change Settings (Note1) Note1: only if Serial Port = Enabled KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.11.2 Page 89 BIOS - Advanced Serial Port 2 Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Serial Port 2 Configuration Serial Port Device Settings [Enabled] IO=2F8h; IRQ=3; Change Settings [Auto] Enable or Disable Serial Port (COM) : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings (Note1) Auto IO=2F8h; IRQ=3; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Super IO device. Note1: only if Serial Port = Enabled KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.11.3 Page 90 BIOS - Advanced Serial Port 3 Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Serial Port 3 Configuration Serial Port Device Settings [Enabled] IO=3E8h; IRQ=7; Change Settings Device Mode [Auto] [Standard Serial Po...] Enable or Disable Serial Port (COM) : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings (Note1) Auto IO=3E8h; IRQ=7; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Super IO device. Device Mode (Note1) Standard Serial Port Mode IrDA 1.0 (HP SIR) Mode ASKIR Mode Change the Serial Port mode. Select <High Speed> or <Normal mode> mode. Note1: only if Serial Port = Enabled KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.11.4 Page 91 BIOS - Advanced Serial Port 4 Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Serial Port 4 Configuration Serial Port Device Settings [Enabled] IO=2E8h; IRQ=10; Change Settings Device Mode [Auto] [Standard Serial Po...] Enable or Disable Serial Port (COM) : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Serial Port Disabled Enabled Enable or Disable Serial Port (COM) Change Settings (Note1) Auto IO=2E8h; IRQ=10; IO=3F8h; IRQ=3,4,5,6,7,10,11,12; IO=2F8h; IRQ=3,4,5,6,7,10,11,12; IO=3E8h; IRQ=3,4,5,6,7,10,11,12; IO=2E8h; IRQ=3,4,5,6,7,10,11,12; Select an optimal setting for Super IO device. Device Mode (Note1) Standard Serial Port Mode IrDA 1.0 (HP SIR) Mode ASKIR Mode Change the Serial Port mode. Select <High Speed> or <Normal mode> mode. Note1: only if Serial Port = Enabled KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.11.5 Page 92 BIOS - Advanced Parallel Port Configuration Note: Parallel Port is not available (connector not mounted). Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Parallel Port Configuration Enable or Disable Parallel Port (LPT/LPTE) Parallel Port Device Settings [Enabled] IO=378h; IRQ=5; Change Settings Device Mode [Auto] [Standard Parallel ...] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Parallel Port Disabled Enabled Enable or Disable Parallel Port (LPT/LPTE) Change Settings (Note1) Auto IO=378h; IRQ=5; IO=378h; IRQ=7,10,11,12; IO=278h; IRQ=5,6,7,10,11,12; IO=3BCh; IRQ=5,6,7,10,11,12; IO=378h; IO=278h; IO=3BCh; Select an optimal setting for Super IO device. (Note1) Standard Parsllel Port Mode EPP Mode ECP Mode EPP Mode & ECP Mode Change the Printer Port mode. Device Mode Note1: only if Parallel Port = Enabled. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 93 BIOS - Advanced 10.2.12 Advanced - Voltage Monitor Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Voltage Monitor VCore 1.05 1.5 3.3 3.3SB 5 12 VBAT : 0.968 V : 1.064 V : 1.512 V : 3.392 V : 3.392 V : 5.188 V : 12.144 V : 3.150 V : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 94 BIOS - Advanced 10.2.13 Advanced - Hardware Health Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Hardware Health Configuration Disabled = Full speed. System Temperature System Temperature Ext CPU Temperature : 30C/86F : 24C/75F : 49.10C/120F Thermal: does regulate fan speed according to specified temperature. System Fan Speed System Temperature Ext Type Fan Cruise Control Fan Settings Fan Min limit Fan Max limit : 1543 RPM [ OneWire @ GPIO16] [Thermal] 35 0 100 Speed: does regulate according to specified RPM. CPU Fan Speed Fan Cruise Control Fan Settings Fan Min limit Fan Max limit : 1374 RPM [Thermal] 50 0 100 Watchdog Function 0 : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 95 Function Selection System Temperature Ext Type (note1) Disabled LM75 @ 0x90 OneWire @ GPIO16 Fan Cruise Control (System Fan) Disabled Thermal Speed Fan Settings (System Fan) 30 - 90 (note2,note3) 1000 - 9999 (note4) Fan Min limit (System Fan) (note5) 0 Fan Max limit (System Fan) (note5) 100 Fan Cruise Control (CPU Fan) Disabled Thermal Speed Fan Settings (CPU Fan) 30 - 90 1000 - 9999 Fan Min limit (CPU Fan) 0 Fan Max limit (CPU Fan) (note7) (note7) Watchdog Function 100 0 - 255 BIOS - Advanced Description (note2) Disabled = Full speed. Thermal: Regulate according to specified C. Speed: Regulate according to specified RPM. (note6) Minimum PWM %, can be used to make sure fan is always active. Make sure Min limit < Max limit. (note6) Maximum PWM %, can be used to limit the fan noise. Make sure Min limit < Max limit. Disabled = Full speed. Thermal: Regulate according to specified C. Speed: Regulate according to specified RPM. (note3) (note4) (note6) (note6) (note8) Minimum PWM %, can be used to make sure fan is always active. Make sure Min limit < Max limit. Maximum PWM %, can be used to limit the fan noise. Make sure Min limit < Max limit. 0 = Disabled. Enter the service interval in seconds before system will reset. Refer to manual how to reload the timer. Note1: Only visible if external temperature sensor like PN1053-4925 "Cable Temperature Sensor - 44P, 400 mm" is connected. Note2: Only visible if external temperature sensor is connected and if System Temperature Ext Type is not Disabled. Note3: C (if Fan Cruise Control = Thermal) use either digit keys to enter value or +/- keys to increase/decrease value. Don't use mix of digit keys and +/- keys. Note4: RPM (if Fan Cruise Control = Speed) use either digit keys to enter value or +/- keys to increase/decrease value by 100. Don't use mix of digit keys and +/- keys. Note5: Only visible if external temperature sensor is connected and if System Fan Cruise Control is Thermal. Note6: Use number keys to enter value. Note7: Only visible if CPU Fan Cruise Control is Thermal. Note8: Seconds, use digit keys to enter value. Value 0 means Watchdog is disabled. Refer to "KT-APIV2 User Manual" to control the Watchdog via API or refer to "KT-API-V2 User Manual DLL" how to control Watchdog via Windows DLL. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 96 BIOS - Advanced 10.2.14 Advanced - Displayblock Setup Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Displayblock Setup LCDVCC Voltage Backlight Signal Inversion [3V3] [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description LCDVCC Voltage 3V3 5V Set the LVDS Display Panel voltage to either 3.3V or 5V. Disabled Enabled Select Disabled if BKLTEN# signal (available in the LVDS connector), shall behave normally: active low to enable backlight. Select Enabled if BKLTEN# signal shall behave inversed: active high to enable backlight. Backlight Signal Inversion KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 97 BIOS - Advanced 10.2.15 Advanced - LAN Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced LAN Configuration System UUID {f4af2da3-b59d-58a9-466cb11a02b0486f} ETH1 Configuration (Left) Wake on LAN MAC Address & Link status: ETH2 Configuration (Upper) MAC Address & Link status: ETH3 Configuration (Lower) MAC Address & Link status: Network [Enabled] [Enabled] 00E0F4288EA3+ [Enabled] 00E0F4288EA4[Enabled] 00E0F4288EA5- Control of Ethernet Devices and PXE boot. To disable ETH1, ME Subsystem must be as well. Stack : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: ETH2 Configuration (Upper) and ETH3 Configuration (Lower) are only present if using KTQM77/mITX. Function Selection Description ETH1 Configuration (Left) Disabled Enabled With PXE boot Control of Ethernet Devices and PXE boot. To disable ETH1, ME Subsystem must be as well. Wake on LAN Enabled Disabled Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be disabled if ME is on at Sx state.) ETH2 Configuration (Upper) Disabled Enabled With PXE boot Control of Ethernet Devices and PXE boot. To disable ETH2, ME Subsystem must be as well. ETH3 Configuration (Lower) Disabled Enabled With PXE boot Control of Ethernet Devices and PXE boot. To disable ETH3, ME Subsystem must be as well. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.15.1 Page 98 BIOS - Advanced Network Stack Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Network stack Ipv4 PXE Support Ipv6 PXE Support Ipv6 Delay Time [Enable] [Enable] [Enable] 0 Enable/Disable UEFI network stack. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Network stack Disable Link Enabled Enable/Disable UEFI network stack. (Note1) Enabled Disabled Enable Ipv4 PXE Boot Support. If disabled IPV4 PXE boot option will not be created. (Note1) Enabled Disabled Enable Ipv6 PXE Boot Support. If disabled IPV6 PXE boot option will not be created. Ipv4 PXE Support Ipv6 PXE Support IPv6 Delay Time (Note1) 0 - 15 (Note2) Set Seconds of Delay Before IPv6 PXE Boot. Default 0 Seconds. Note1: Only if Network stack = Enabled. Note2: To enter number use digit keys and/or +/- keys. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 99 BIOS - Advanced 10.2.16 Advanced - Delay Startup Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Delay startup Delay Startup 0 : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Delay Startup 0 - 9999 Description Note1) Delay startup value is in ms. Note1: To enter number use digit keys and/or +/- keys. The delay initiates if the value is different from 0, starts at the earliest possible point of the BIOS boot. For some add-on devices the BIOS boot is too fast for proper detection. In other words, the setting is meant as a possible fix to Add-on device detection problems. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 100 BIOS - Advanced 10.2.17 Advanced - Serial Port Console Redirection Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced COM0 Console Redirection Console Redirection Settings [Disabled] COM1 Console Redirection Console Redirection Settings [Disabled] COM2 Console Redirection Console Redirection Settings [Disabled] COM3 Console Redirection Console Redirection Settings [Disabled] Console Redirection Enable or Disable. COM4(Pci Bus0,Dev0,Func0) (Disabled) Console Redirection Port Is Disabled Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection Redirection Settings Console [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.2.17.1 Page 101 BIOS - Advanced Console Redirection Settings The Console Redirection Settings menu are only available if related Console Redirection is Enabled. A different menu is available for Serial Port for Out-of-Band Management, see next page. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced COM0 Console Redirection Settings Terminal Type Bits per second Data Bits Parity Stop Bits Flow Control VT-UTF8 Combo Key Support Recorder Mode Resolution 100x31 Legacy OS Redirection Resolution Putty Keypad Redirection After BIOS POST [ANSI] [115200] [8] [None] [1] [None] [Enabled] [Disabled] [Disabled] [80x24] [VT100] [Always Enable] Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 102 BIOS - Advanced Function Selection Description Terminal Type VT100 VT100+ VT-UTF8 ANSI Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VTUTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes. Bits per second 9600 19200 38400 57600 115200 Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. Data Bits 7, 8 Data Bits None Even Odd Mark Space A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the num of 1's in the data bits is even. Odd: parity bit is 0 if the num of 1's in the data bits is odd. Mark: parity bit is always 1. Space: parity bit is always 0. Mark/Space do not allow error detection. 1 2 Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Flow Control None Hardware RTS/CTS Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a stop signal can be sent to stop the data flow. Once the buffers are empty, a start `signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signals. VT-UTF8 Combo Key Support Disabled Enabled Enable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. Recorder Mode Disabled Enabled On this mode enabled only text will be send. This is to capture Terminal data. Resolution 100x31 Disabled Enabled Enables or disables extended terminal resolution. Legacy OS Redirection Resolution 80x24 80x25 On Legacy OS, the Number of Rows and Columns supported redirection. Putty Keypad VT100 LINUX XTERMR6 SCO ESCN VT400 Select FunctionKey and KeyPad on Putty. Always Enable BootLoader The settings specify if BootLoader is selected than Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy console Redirection is enabled for Legacy OS. Parity Stop Bits Redirection After BIOS POST KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 103 BIOS - Advanced When Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS) > Console Redirection is enabled: Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced Out-of-Band Mgmt Port Terminal Type Bits per second Flow Control Data Bits Parity Stop Bits [COM0] [VT-UTF8] [115200] [None] 8 None 1 Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Out-of-Band Mgmt Port COM0 COM1 COM2 COM3 COM4 (Pci Bus0,Dev0, Func0) (Disabled) Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port. Terminal Type VT100 VT100+ VT-UTF8 ANSI VT-UTF8 is the preferred terminal type for outof-band management. The next best choice is VT100+ and then VT100. See above, in Console Redirection Settings page, for more Help with Terminal Type/Emulation. Bits per second 9600 19200 57600 115200 Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. None Hardware RTS/CTS Software Xon/Xoff Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a stop signal can be sent to stop the data flow. Once the buffers are empty, a start `signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signals. Flow Control KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 104 BIOS - Advanced 10.2.18 Advanced - CPU PPM Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Advanced CPU PPM Configuration EIST Turbo Mode CPU C3 Report CPU C6 Report CPU C7 Report Config TDP LOCK Long duration power limit Long duration maintained Short duration power limit ACPI T State Enable/Disable Intel SpeedStep [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] 0 0 0 [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 105 BIOS - Advanced Function Selection Description EIST Disabled Enabled Enable/Disable Intel SpeedStep. Disabled Enabled Turbo Mode CPU C3 Report Disabled Enabled Enable/Disable CPU C3 (ACPI C2) report to OS CPU C6 Report Disabled Enabled Enable/Disable CPU C6 (ACPI C3) report to OS CPU C7 Report Disabled Enabled Enable/Disable CPU C7 (ACPI C3) report to OS Config TDP LOCK Disabled Enabled Lock the Config TDP Control register. Long duration power limit 0 - 255 (Note2) Long duration power limit in Watts, 0 means use factory default. Long duration maintained 0 - 120 (Note2) Time window which the long duration power is maintained. Short duration power limit 0 - 255 (Note2) Short duration power limit in Watts, 0 means use factory default. ACPI T State Disabled Enabled Turbo Mode (Note1) Enable/Disable ACPI T State support. Note1: Not present when using Intel Celeron B810 CPU or i3 Core CPU. Note2: To enter number use digit keys. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.3 Page 106 BIOS - Chipset Chipset Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit PCH-IO Configuration System Agent (SA) Configuration PCH Parameters : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F BIOS - Chipset Page 107 10.3.1 PCH-IO Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset Intel PCH RC Version Intel PCH SKU Name Intel PCH Rev ID 1.5.0.0 QM77 04/C1 PCI Express Configuration settings PCI Express Configuration USB Configuration PCH Azalia Configuration Restore AC Power Loss [Power On] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: Intel PCH SKU Name depends on the actual board type, QM77 or HM76. Please fid description of the PCI Express Configuration, USB Configuration and PCH Azalia Configuration on the following pages. Function Selection Description Restore AC Power Loss Power Off Power On Last State Select AC Power state when power is re-applied after a power failure. KTQM77 - KTHM76 Users Guide KTD-N0850-F BIOS - Chipset Page 108 10.3.1.1 PCI Express Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PCI Express Configuration Subtractive Decode Subtractive Decode Port# PCI PCI PCI PCI PCI PCI PCI Enable or disable PCI Express Subtractive Decode. [Disabled] 0 Express Root Port 1 Express Root Port 2 Express Root Port 3 Express Root Port 4 Express Root Port 6 Express Root Port 7 Express Root Port 8 : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Subtractive Decode Disabled Enabled Enable or disable PCI Express Subtractive Decode. Subtractive Decode Port# (Note1) 0 (Note2) Select PCI Express Subtractive Decode Root Port. User to ensure port availability. Note1: Only visible if Subtractive Decode is Enabled. Note2: To enter number use digit keys and/or +/- keys. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 109 BIOS - Chipset 10.3.1.1.1 PCI Express Root Port (1-4, 6-8) Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PCI Express Root Port (1-4, 6-8) ASPM Support PME SCI PCIe Speed [Enabled] [Disabled] [Enabled] [Auto] Control the PCI Express Root Port. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description PCI Express Root Port (14, 6-8) Disabled Enabled Control the PCI Express Root Port. ASPM Support Disabled L0s L1 L0sL1 Auto Set the ASPM Level. Disabled: Disabled ASPM L0s: Force all links to L0s State Auto: BIOS auto configure PME SCI Disabled Enabled Enable or disable PCI Express PME SCI. PCIe Speed Auto Gen1 Gen2 Select PCI Express port speed. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 110 BIOS - Chipset 10.3.1.2 USB Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset USB Configuration XHCI Pre-Boot Driver xHCI Mode HS Port #1 Switchable HS Port #2 Switchable HS Port #3 Switchable HS Port #4 Switchable xHCI Streams [Enabled] [Smart Auto] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] ECHI1 [Enabled] ECHI2 [Enabled] USB Ports Per-Port Disable Control [Disabled] Enable or disable XHCI PreBoot Driver support. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 111 BIOS - Chipset Function Selection Description XHCI Pre-Boot Driver Enabled Disabled Enable or disable XHCI Pre-Boot Driver support. xHCI Mode Smart Auto Auto Enabled Disabled Mode of operation of xHCI controller. HS Port #1 Switchable HS Port #2 Switchable HS Port #3 Switchable HS Port #4 Switchable (Note1) Disabled Enabled Allows for HS port switching between xHCI and EHCI. If disabled, port is routed to EHCI. If HS port is routed to xHCI, the corresponfing SS port is enabled. xHCI Streams Disabled Enabled Enable xHCI Maximum Primary Stream Array Size. ECHI1 Disabled Enabled Control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. ECHI2 Disabled Enabled Control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled. USB Ports Per-Port Disable Control Disabled Enabled Control each of the USB ports (0 - 13) disabling. USB Port #(0-13) Disabled (Note2) Disabled Enabled Disabled USB port. Note1: Not visible if xHCI Mode is Disabled. Note2: Only visible if USB Ports Per-Port Disable Control is Enabled. The USB6 and USB7 are not supported by the KTHM76/mITX. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 112 BIOS - Chipset 10.3.1.3 PCH Azalia Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PCH Azalia Configuration Azalia Audio Jack Sensing Azalia Internal HDMI codec Azalia HDMI codec Port B Azalia HDMI codec Port C Azalia HDMI codec Port D Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be unconditionally enabled. Auto = Azalia will be enabled if present, disabled otherwise. [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Azalia Disabled Enabled Auto Control Detection of the Azalia device. Disabled = Azalia unconditionally disabled. Enabled = Azalia unconditionally enabled. Auto = Azalia enabled if present, disabled otherwise. Audio Jack Sensing (Note1) Disabled Auto Auto: The insertions of audio jacks are auto determined. Disabled: Driver assumes that all jacks are inserted (useful when using the Audio pinrow) Azalia Internal HDMI codec (Note1) Disabled Enabled Enable or disable internal HDMI codec for Azalia. Azalia HDMI codec PortB Azalia HDMI codec PortC Azalia HDMI codec PortD (Note2) Disabled Enabled Enable or disable internal HDMI codec for Azalia. Note1: Only visible if Azalia is not Disabled. Note2: Only visible if Azalia is not Disabled and Azalia Internal HDMI codec is Enabled. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 113 BIOS - Chipset 10.3.2 System Agent (SA) Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset System Agent Bridge Name System Agent Bridge Name VT-d Capability IvyBridge 1.5.0.0 Supported VT-d CHAP Device (B0:D7:F0) Thermal Device (B0:D4:F0) Enable NB CRID BDAT ACPI Table Support C-State Pre-Wake [Enabled] [Disabled] [Disabled] [Disabled] [Disabled] [Enabled] Check to enable VT-d function on MCH. Graphics Configuration DMI Configuration NB PCIe Configuration Memory Configuration Memory Thermal Configuration GT - Power Management Control : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description VT-d Disabled Enabled Check to enable VT-d function on MCH. CHAP Device (B0:D7:F0) Enabled Disabled Enable or disable SA CHAP Device. Thermal Device (B0:D4:F0) Enabled Disabled Enable or disable SA Thermal Device. Enable NB CRID Enabled Disabled Enable or disable NB CRID Workaround. BDAT ACPI Table Support Enabled Disabled Enables support for the BDAT ACPI Table. Enabled Disabled Controls C-State Pre-Wake feature for ARAT, in SSKPD[57] C-State Pre-Wake (Note1) Note 1: Only present if Ivy Bridge CPU is used. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 114 BIOS - Chipset 10.3.2.1 Graphics Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset Graphics Configuration IGFX VBIOS Version IGFX Frequency Graphics Turbo IMON Current Primary Display Internal Graphics GTT Size Aperture Size DVMT Pre-Allocated DVMT Total Gfx Mem Gfx Low Power Mode Graphics Performance Analyzers LCD Control 2124 350 MHz 31 [Auto] [Auto] [2MB] [256MB] [64M] [256M] [Enabled] [Disabled] Graphics turbo IMON current values supported (14 - 31). : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 115 BIOS - Chipset Function Selection Description Graphics Turbo IMON Current 31 Graphics turbo IMON current values supported (14 - 31). Primary Display Auto IGFX PEG PCI Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx. Internal Graphics Auto Disabled Enabled Keep IGD enabled based on the setup options. GTT Size 1MB 2MB Select the GTT Size. Aperture Size 128MB 256MB 512MB Select the Aperture Size. DVMT Pre-Allocated 32M, 64M, 96M,128M, 160M, 192M, 224M, 256M, 288M, 320M, 352M, 384M, 416M, 448M, 480M, 512M, 1024M Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem 128M 256M MAX Select DVMT 5.0 Total Graphics Memory size used by the Internal Graphics Device. Gfx Low Power Mode Enabled Disabled This option is applicable for SSF only. Graphics Performance Analyzers Enabled Disabled Enable or disable Intel Graphics Performance Analyzers Counters. KTQM77 - KTHM76 Users Guide KTD-N0850-F BIOS - Chipset Page 116 10.3.2.1.1 LCD Control Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset LCD Control Primary IGFX Boot Display LCD Panel Type SDVO-LFP Panel Type Panel Scaling Backlight Control BIA Spread Spectrum clock Chip TV1 Standard TV2 Standard ALS Support Active LFP Panel Color Depth [VBIOS Default] [VBIOS Default] [VBIOS Default] [Auto] [PWM Inverted] [Auto] [Off] [VBIOS Default] [VBIOS Default] [Disabled] [No LVDS] [18 Bit] Select the Video Device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 117 BIOS - Chipset Function Selection Description Primary IGFX Boot Display VBIOS Default CRT (DVI-A, default 1) EFP (DVI-D, default 1) LFP (LVDS display) EFP3 (DP2 display) EFP2 (DP1, default 2) LFP2 Select the Video Device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. LCD Panel Type VBIOS Default 640x480 800x600 1024x768 1280x1024 1400x1050(RB) 1400x1050 1600x1200 1366x768 1680x1050 1920x1200 1440x900 1600x900 1024x768 1280x800 1920x1080 2048x1536 Select LCD panel used by Internal Graphics Device by selecting the appropriate setup item. SDVO-LFP Panel Type VBIOS Default 1024x768 SDVO-LFP 1280x1024 SDVO-LFP 1400x1050 SDVO-LFP 1600x1200 SDVO-LFP Select SDVO panel used by Internal Graphics Device by selecting the appropriate setup item. Panel Scaling Auto Off Force Scaling Select the LCD panel scaling option used by Internal Graphics Device. Backlight Control PWM Inverted PWM Normal GMBus Inverted GMBus Normal Backlight Control Setting BIA Auto Disabled Level 1 Level 2 Level 3 Level 4 Level 5 Auto: GMCH use VBT defaults. Level n: Enabled with selected Aggressiveness Level. Spread Spectrum clock Chip Off Hardware Software Hardware: Spread is controlled by chip. Software: Spread is controlled by BIOS. LVDS LVDS LVDS1 LVDS LVDS1 LVDS2 LVDS LVDS LVDS LVDS LVDS LVDS LVDS2 LVDS LVDS LVDS KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 118 BIOS - Chipset Function Selection Description TV1 Standard VBIOS Default NTSC_M NTSC_M_J NTSC_433 PAL_B PAL_G PAL_D PAL_H PAL_I PAL_M PAL_N SECAM_L SECAM_B SECAM_D SECAM_G SECAM_H SECAM_K HDTV_STD_SMPTE_240M_1080i59 HDTV_STD_SMPTE_240M_1080i60 HDTV_STD_SMPTE_295M_1080i50 HDTV_STD_SMPTE_295M_1080p50 HDTV_STD_SMPTE_296M_720p50 HDTV_STD_SMPTE_296M_720p60 HDTV_STD_CEAEIA_7702A_480p60 HDTV_STD_CEAEIA_7702A_480i60 Select the ability to configure a TV Format. TV2 Standard VBIOS Default NTSC_M NTSC_M_J NTSC_433 PAL_B PAL_G PAL_D PAL_H PAL_I PAL_M PAL_N SECAM_L SECAM_B SECAM_D SECAM_G SECAM_H SECAM_K HDTV_STD_SMPTE_240M_1080i59 HDTV_STD_SMPTE_240M_1080i60 HDTV_STD_SMPTE_295M_1080i50 HDTV_STD_SMPTE_295M_1080p50 HDTV_STD_SMPTE_296M_720p50 HDTV_STD_SMPTE_296M_720p60 HDTV_STD_CEAEIA_7702A_480p60 HDTV_STD_CEAEIA_7702A_480i60 Select the ability to configure a TV Minor Format. KTQM77 - KTHM76 Users Guide KTD-N0850-F Function Page 119 BIOS - Chipset Selection Description Enabled Disabled Valid only for ACPI. Legacy = ALS Support through the IGD INT10 function. SCPI = ALS support through an ACPI ALS driver. Active LFP No LVDS Int-LVDS SDVO LVDS eDP Port-A eDP Port-D Select the Active LFP Configuration. No LVDS: VBIOS does not enable LVDS. Int-LVDS: VBIOS enables LVDS driver by SDVO encoder. SDVO LVDS: VBIOS enables LVDS driver by SDVO encoder. eDP Port-A: LFP driven by Internal DisplayPort encoder from Port-A. Panel Color Depth 18 Bit 24 Bit Select the LFP Panel Color Depth. ALS Support KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 120 BIOS - Chipset 10.3.2.2 DMI Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset DMI Configuration Enable or disable DMI Vc1. DMI X4 Gen2 DMI Vc1 Control DMI Vcp Control DMI Vcm Control DMI Link ASPM Control DMI Extended Synch Control DMI Gen 2 [Enabled] [Enabled] [Enabled] [L0sL1] [Disabled] [Auto] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description DMI Vc1 Control Enabled Disabled Enable or disable DMI Vc1 DMI Vcp Control Enabled Disabled Enable or disable DMI Vcp DMI Vcm Control Enabled Disabled Enable or disable DMI Vcm DMI Link ASPM Control Disabled L0s L1 L0sL1 Enable or disable the control of Active State Power Management on SA side of the DMI Link. DMI Extended Synch Control Enabled Disabled Enable DMI Extended Synchronization. DMI Gen 2 Auto Enabled Disabled Enable or disable DMI Gen 2. Auto means Disabled for IVB A0 MB/DT and IVB B0 MB, Enabled for other CPUs. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 121 BIOS - Chipset 10.3.2.3 NB PCIe Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset NB PCIe Configuration PEG0 PEG0 - Gen X PEG0 ASPM Not Present [Auto] [Disabled] PCIe PEG Bifurcation Enable PEG Detect Non-Compliance Device De-emphasis Control PEG Sampler Calibrate Swing Control Gen3 Equalization Gen3 Eq Phase 2 [1 x16] [Auto] [Disabled] [-3.5 dB] [Auto] [Full] [Enabled] [Auto] PEG Gen3 Root Port Preset Value for each Lane PEG Gen3 Endpoint Preset Value each Lane PEG Gen3 Endpoint Hint Value each Lane Gen3 Eq Preset Search PEG Link Disabled Fast PEG Init RxCEM Loop back PCIe Gen3 RxCTLEp Setting [Disabled] [Disabled] [Enabled] [Disabled] 12 Configure PEG0 B0:D1:F0 Gen1-Gen3 : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: PCIe PEG Bifurcation is only supported on KTQM77/mITX having PCB ID 01 or above. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 122 BIOS - Chipset Function Selection Description PEG0 - Gen X Auto GEN1 Gen2 Configure PEG0 B0:D1:F0 Gen1-Gen3 PEG0 ASPM Disabled Auto ASPM L0s ASPM L1 ASPM L0sL1 Control ASPM support for the PEG: Device 1 Function 0. This has no effect if PEG is not the currently active device. PCIe PEG Bifurcation 1 x16 2 x8 1 x8, 2 x4 "2 x8" and "1 x8, 2 x4" need Riser Card with bifurcation functionality to work. Only supported on KTQM77/mITX having PCB ID 01 or above. Enable PEG Disabled Enabled Auto To enable or disable the PEG. Detect Non-Compliance Device Disabled Enabled Detect Non-Compliance PCI Express Device in PEG. De-emphasis Control -6 dB -3.5 dB Configuring the De-emphasis Control on PEG. PEG Sampler Calibrate Auto Enabled Disabled Enable or disable PEG Sampler Calibrate. Auto means Disabled for SNB MB/DT, Enabled for IVB A0 B0. Swing Control Reduced Half Full Perform PEG Swing Control, on IVB C0 and Later. Enabled Disabled Perform PEG Gen3 Equalization steps. Auto Enabled Disabled Perform PEG Gen3 Equalization phase 2. Enabled Disabled Perform PEG Gen3 Preset Search algorithm, on IVB Co or Later. PEG Link Disabled Enabled Disabled Enable or disable PCIe link disable mechanism for additional power saving. Fast PEG Init Enabled Disabled Enable or disable Fast PEG Init, Some optimization if not PEG devices present in cold boot. RxCEM Loop back Enabled Disabled Enable or disable RxCEM Loop back. PCIe Gen3 RxCTLEp Setting (Note1) 0-11, 12, 13-15 The range of the setting is (0-15). This setting has to be specified based on platform design and following the guideline. Gen3 Equalization (Note1) Gen3 Eq Phase 2 (Note1) Gen3 Eq Preset Search (Note1) Note 1: Only present if Ivy Bridge CPU is used. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 123 BIOS - Chipset Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PEG Gen3 Root Port Preset Value for each Lane Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane 11 Lane 12 Lane 13 Lane 14 Lane 15 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 Value for Lane 0. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 124 BIOS - Chipset Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PEG Gen3 Endpoint Preset Value each Lane Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane 11 Lane 12 Lane 13 Lane 14 Lane 15 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 Value for Lane 0. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 125 BIOS - Chipset Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset PEG Gen3 Endpoint Hint Value each Lane Lane 0 Lane 1 Lane 2 Lane 3 Lane 4 Lane 5 Lane 6 Lane 7 Lane 8 Lane 9 Lane 10 Lane 11 Lane 12 Lane 13 Lane 14 Lane 15 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Value for Lane 0. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 126 BIOS - Chipset 10.3.2.4 Memory Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset Memory Information Memory RC Version Memory Frequency Total Memory DIMM#0 DIMM#2 CAS Latency (tCL) Minimum delay time CAS to RAS (tRCDmin) Row Precharge (tRPmin) Active to Precharge (tRASmin) XMP Profile 1 XMP Profile 1 DIMM profile Memory Frequency Limiter ECC Support Max TOLUD NMode Support Memory Scrambler MRC Fast Boot Force Cold Reset DIMM Exit Mode Power Down Mode Select DIMM timing profile that should be used. 1.5.0.0 1333 Mhz 4096 MB (DDR3) 4096 MB (DDR3) Not Present 9 9 9 24 Not Supported Not Supported : Select Screen : Select Item [Default DIMM profile] Enter: Select [Auto] +/- : Change Opt. [Enabled] F1: General Help [Dynamic] F2: Previous Values [Auto] F3: Optimized Defaults [Enabled] F4: Save & Exit [Enabled] ESC: Exit [Enabled] [Fast Exit] [PPD] Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description DIMM profile Default DIMM profile Custom Profile XMP Profile 1 XMP Profile 2 Select DIMM timing profile that should be used. Memory Frequency Limiter Auto 1067 1333 1600 1867 2133 2400 2667 Maximum Memory Frequency Selections in Mhz. ECC Support Disabled Enabled Enable or disable DDR Ecc Support. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 127 BIOS - Chipset Table continued: Function Selection Description Max TOLUD Dynamic 1 GB 1.25 GB 1.5 GB 1.75 GB 2 GB 2.25 GB 2.5 GB 2.75 GB 3 GB 3.25 GB Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller. NMode Support Auto 1N Mode 2N Mode Nmode Support Option Memory Scrambler Enabled Disabled Enable or disable memory scrambler. MRC Fast Boot Enabled Disabled Enable or disable MRC Fast Boot Force Cold Reset Enabled Disabled Force cold reset or choose MRC cold reset mode, when cold boot is required during MRC execution. Note: If ME 5.0MB is present, Force cold reset is required! DIMM Exit Mode Auto Slow Exit Fast Exit DIMM Exit Mode control. No Power Down APD PPD APD-PPD Power Down Mode control. Scrambler Seed Generation Off Enabled Disabled Control Memory Scrambler Seed Generation. Enable - do not generate scrambler seed. Disable - Generate scrambler seed always. Memory Remap Enabled Disabled Enable or disable Memory Remap above 4G. Memory Alias Check Enabled Disabled Enable or disable Memory Alias Check. Channel A DIMM Control Enable Both DIMMS Disable DIMM0 Disable DIMM1 Disable Both DIMMS Enable or disable dims on channel A. Channel B DIMM Control Enable Both DIMMS Disable DIMM0 Disable DIMM1 Disable Both DIMMS Enable or disable dims on channel B. Power Down Mode KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 128 BIOS - Chipset 10.3.2.5 Memory Thermal Configuration Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset Memory Thermal Configuration Memory Thermal Management PECI Injected Temperature EXTTS# via TS-on-Board EXTTS# via TS-on-DIMM Virtual Temperature Sensor (VTS) Enable or disable Memory Thermal Management. [Enabled] [Disabled] [Disabled] [Disabled] [Disabled] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Memory Thermal Management Disabled Enabled Enable or disable Memory Thermal Management. PECI Injected Temperature Enabled Disabled Enable or disable memory temperatures to be injected to the processor via PECI. EXTTS# via TS-on-Board Enabled Disabled Enable or disable routing TS-on-Board to be injected to EXTTS# pins on the PCH. EXTTS# via TS-on-DIMM Enabled Disabled Enable or disable routing TS-on-DIMM to be injected to pin on the PCH. Virtual Temperature Sensor (VTS) Enabled Disabled Enable or disable Virtual Temperature Sensor (VTS). KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 129 BIOS - Chipset 10.3.2.6 GT - Power Management Control Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Chipset GT - Power Management Control GT Info GT2 (0x166) RC6 (Render Standby) RC6+(Deep RC6) GT Overclocking Support [Enabled] [Enabled] [Disabled] Check to enable render standby support. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description RC6 (Render Standby) Enabled Disabled Check to enable render standby support. RC6+(Deep RC6) Enabled Disabled Check to enable Deep RC6 (RC6+) support. GT Overclocking Support Enabled Disabled Enable or disable GT Overclocking Support. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.4 BIOS - Boot Page 130 Boot Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Setup Prompt Timeout Bootup NumLock State 1 [On] Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Quit Boot Fast Boot [Disabled] [Disabled] CSM16 Module Version 07.69 GateA20 Active Option ROM Message INT19 Trap Response [Upon Request] [Force BIOS] [Immediate] Driver Option Priorities Boot Option Priorities Boot Option #1 Force Boot Setup CSM parameters [P1: ST3120827AS ...] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Note: When pressing <F7> while booting it is possible manually to select boot device. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 131 BIOS - Boot Function Selection Description Setup Prompt Timeout 1, 2 - 65535 Bootup NumLock State On Off Select the Keyboard Numlock state. Quit Boot Disabled Enabled Enables or disables Quiet Boot option. Fast Boot Disabled Enabled Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options. GateA20 Active Upon Request Always Upon Request: GA20 can be disabled using BIOS services. Always: do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM Message Force BIOS Keep Current Set display mode for Option ROM. INT19 Trap Response Immediate Postponed BIOS reaction on INT19 trapping by Option ROM. Immediate: execute the trap right away. Postponed: execute the trap during legacy boot. Boot Option #1 (list of bootable devices) Sets the system boot order. (Note) Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting. Note: To enter number use digit keys and/or +/- keys. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 132 BIOS - Boot 10.4.1 Force Boot Setup Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Force Boot Setup Force Boot 1st Boot Port # 2nd Boot Device Name 3rd Boot 4th Boot [Enabled] [Sata Port] 1 [Device Name] [ST3120827AS] [USB ] [N/A] This option controls if CSM will be launched. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Force Boot Disabled Enabled 1st Boot (2nd Boot) (3rd Boot) (4th Boot) Note1 N/A USB SATA SATA Port Device Name Port # Note2 0-5 Note3 None ST3120827AS *N/A * *N/A * *N/A * Device Name st nd rd Description Note4 th Note 1: 1 Boot, 2 Boot, 3 Boot and 4 Boot have the same set of selections. Note 2: Only shown if SATA Port is selected. Note 3: Only shown if Device Name is selected. Note 4: By +/- key select requested port number. Make sure only valid number (0 - 5) is selected. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 133 BIOS - Boot 10.4.2 CSM parameters Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Launch CSM Boot option filter Launch PXE OpROM policy Launch Storage OpROM policy Launch Video OpROM policy Other PCI device ROM priority [Always] [UEFI and Legacy] [Do not launch] [Legacy only] [Legacy only] [Legacy OpROM] This option controls if CSM will be launched. : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Launch CSM Auto Always Never This option controls if CSM will be launched. Boot option filter UEFI and Legacy Legacy only UEFI only This option controls what devices system can boot to. Launch PXE OpROM policy Do not launch UEFI only Legacy only Controls the execution of UEFI and Legacy PXE OpROM. Launch Storage OpROM policy Do not launch UEFI only Legacy only Controls the execution of UEFI and Legacy Storage OpROM. Launch Video OpROM policy Do not launch UEFI only Legacy only Controls the execution of UEFI and Legacy Video OpROM. Other PCI device ROM priority UEFI OpROM Legacy OpROM For PCI devices other than Network, Mass storage or Video defines which OpROM to launch. KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.5 Page 134 BIOS -Security Security Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Administrator Password If ONLY the Administrator's password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User's password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20 Administrator Password User Password Password on popup menu [Enabled] System Mode state Secure Boot state Setup Disabled Secure Boot Secure Boot Mode Image Execution Policy Key Management : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit [Enabled] [Custom] HDD Security Configuration: P1:ST3120827AS Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Administrator Password (See Password description above) Set Administrator Password User Password (See Password description above) Set User Password Password on popup menu Disabled Enabled Password on F7 popup boot menu. Secure Boot Disabled Enabled Secure Boot flow control. Secure Boot is possible only if System runs in User Mode. Secure Boot Mode Standard Custom Secure Boot mode selector. Standard: fixed Secure boot policy. Custom: changeable Image Execution policy and Secure Boot Key databases. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 135 BIOS -Security 10.5.1 Image Execution Policy Only visible if Secure Boot Mode = Custom. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Internal FV Option ROM Removable Media Fixed Media [Always Execute] [Deny Execute] [Deny Execute] [Deny Execute] Image Execution Policy on Security Violation. Image load device path : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Internal FV Always Execute Image Execution Policy on Security Violation. Image load device path. Option ROM Always Execute Always Deny Allow Execute Defer Execute Deny Execute Query User Image Execution Policy on Security Violation. Image load device path. Removable Media Always Execute Always Deny Allow Execute Defer Execute Deny Execute Query User Image Execution Policy on Security Violation. Image load device path. Fixed Media Always Execute Always Deny Allow Execute Defer Execute Deny Execute Query User Image Execution Policy on Security Violation. Image load device path. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 136 BIOS -Security 10.5.2 Key Management Only visible if Secure Boot Mode = Custom. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Default Key Provisioning [Disabled] Force OEM default Secure Boot Keys if System is in Setup Mode. Manage All Factory Keys (PK,KEK;DB,DBX) Install default Secure Boot keys Platform Key (PK) Set PK from File Get PK to File Delete the PK Key Exchange Key Database (KEK) Set KEK from File Get KEK to File Delete the KEK Append an entry to KEK Key Exchange Key Database (DB) Set DB from File Get DB to File Delete the DB Append an entry to DB Key Exchange Key Database (DBX) Set DBX from File Get DBX to File Delete the DBX Append an entry to DBX [NOT INSTALLED] [NOT INSTALLED] [NOT INSTALLED] [NOT INSTALLED] : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Default Key Provisioning Disabled Enabled Force OEM default Secure Boot Keys if System is in Setup Mode. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 137 BIOS -Security 10.5.3 HDD Security Configuration Only visible if entering a device listed below HDD Security Configuration. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit HDD Password Description : Allows Access to set, Modify and Clear HardDisk User and Master Passwords. User Password need to be installed for Enabling Security. Master Password can be modified only when successfully unlocked with Master Password in POST. Set HDD User Password. *** Advisable to Power Cycle System after Setting Hard Disk Passwords *** HDD PASSWORD CONFIGURATION: Security Supported Security Enabled Security Locked Security Frozen HDD User Pwd Status HDD Master Pwd Status : : : : Yes No No No NOT INSTALLED INSTALLED Set User Password : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Selection Description Set User Password Create New Password Set HDD User Password. *** Advisable to Power Cycle System after Setting Hard Disk Passwords *** KTQM77 - KTHM76 Users Guide KTD-N0850-F 10.6 BIOS - Save & Exit Page 138 Save & Exit This Menu is special; having no "selections" for each function, or in other words, the function is the same as the selection. Aptio Setup Utility - Copyright (c) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Exit system setup after saving the changes. Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override P0: ST3120827AS Launch EFI Shell From filesystem device : Select Screen : Select Item Enter: Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.15.1226. Copyright (c) 2012 American Megatrends, Inc Function Description Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset Reset the system without saving any changes. Save Changes Save Changes done so far to any of the setup options. Discard Changes Discard Changes done so far to any of the setup options. Restore Defaults Restore/Load Default values for all the setup options. Save as User Defaults Save the Changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. (possible list of boot devices) Selection table of bootable devices. When selected system will boot on selected device. (See note below) Launch EFI Shell From filesystem device Attempts to Launch EFI Shell application (Shellx64.efi) from one of the available filesystem devices. Note: When pressing <F7> while booting it is possible manually to select boot device. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 139 BIOS - Beep/POST 11 AMI BIOS Beep Codes Boot Block Beep Codes: Number of Description Beeps 1 Insert diskette in floppy drive A: 2 `AMIBOOT.ROM' file not found in root directory of diskette in A: 3 Base Memory error 4 Flash Programming successful 5 Floppy read error 6 Keyboard controller BAT command failed 7 No Flash EPROM detected 8 Floppy controller failure 9 Boot Block BIOS checksum error 10 Flash Erase error 11 Flash Program error 12 `AMIBOOT.ROM' file size error 13 BIOS ROM image mismatch (file layout does not match image present in flash device) POST BIOS Beep Codes: Number of Description Beeps 1 Memory refresh timer error. 2 Parity error in base memory (first 64KB block) 3 Base memory read/write test error 4 Motherboard timer not operational 5 Processor error 6 8042 Gate A20 test error (cannot switch to protected mode) 7 General exception error (processor exception interrupt error) 8 Display memory error (system video adapter) 9 AMIBIOS ROM checksum error 10 CMOS shutdown register read/write error 11 Cache memory test failed Troubleshooting POST BIOS Beep Codes: Number of Troubleshooting Action Beeps 1, 2 or 3 Reset the memory, or replace with known good modules. 4-7, 9-11 Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond "all hope", eliminate the possibility of interference due to a malfunctioning add-in card. Remove all expansion cards, except the video adapter. * If beep codes are generated when all other expansion cards are absent, consult your system manufacturer's technical support. * If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card. 8 If the system video adapter is an add-in card, replace or reset the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty. Note: If Motherboard beeps fast for approximately two seconds (~20 beeps) and then turns off, then Jumper (J37) is missing, meaning that "Load Default BIOS Settings" function is enabled until J37 is back in place. KTQM77 - KTHM76 Users Guide KTD-N0850-F Page 140 OS Setup 12 OS Setup Use the Setup.exe files for all relevant drivers. The drivers can be found on KTQM77 Driver CD or they can be downloaded from the homepage http://www.kontron.com/ For some OS like Win7 when installing OS via USB DVD, USB Keyboard/Mouse, please connect the USB DVD, USB Keyboard/Mouse to USB2.0 ports only or disable USB3.0 in BIOS. KTQM77 - KTHM76 Users Guide