G-2 APEMwww.apem.com
G
A1-A01-A02-A03 series
Industrial controls
Distinctive features
The A01 and A02 series offer ranges of :
- pushbutton switches, illuminated or not
- indicators
- 2 or 3 position keylock switches
- 2 or 3 position rotary lever switches
- emergency stop switches
with rectangular, square or round operators.
Environmental protection : IP65
Modular construction
Electrical life : 50.000 cycles min.
Screen engraving or insertable legends on request
Approvals (for switch blocks only)
UL 1054 BS RIA 20 Shock & Vibration
EN 61058-1
A01 - A1 - A03 series
Panel cut-out :
Ø 16 mm (.630), except :
- flush mount round : Ø 22 mm (.866)
- flush mount rectangular : 20.60 x 26.70 mm
- flush mount square : 20.60 x 20.60 mm
- A1 series : Ø 22 mm (.866)
- A03 series : round or square Ø 22 (.866)
flush mount : Ø 30 mm (1.378)
1, 2, 3 and 4 poles
Solder lug/quick-connect terminals
Contacts : silver, gold plated
Current/voltage rating :
6A 250VAC max. - 10mA 5VAC min.
These values are applicable for all components, accessories
and lamps, unless otherwise specified in the following pages.
Lamp : filament, neon or LED
A02 series
Panel cut-out :
- round or square : Ø 22 mm (.866)
- rectangular : 29,5 x 21,5 mm (1.160x.846)
- flush mount : Ø 30 mm (1.378)
1 and 2 poles
Screw terminals (optional : quick-connect term.)
Contacts : silver
Current/voltage rating : 12A 380VAC
16A 250VAC max. - 25mA 5VAC min.
These values are applicable for all components, accessories
and lamps, unless otherwise specified in the following pages.
Lamp : filament, neon, LED
or special multi-LED array
Option : end cap terminal guard. Order separately (see
end of A02 series).
Each sub-assembly has
to be ordered separately.
Packaging unit :
A1 : 25 pieces - A01 : 20 pieces (except pushbuttons: 25 pieces) - A02 : 25 pieces - A03 : 10 pieces.
Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
The company reserves the right to change specifications without notice.
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page2
UG1410A
APEM www.apem.com G-3
G
A1-A01-A02-A03 series
Industrial controls
Specifications for pushbutton, keylock and rotary switches
ELECTRICAL SPECIFICATIONS
A01 - A1 - A03 A02
Function :
Momentary Momentary
or maintained action or maintained action
Current/voltage rating : 10mA 5VAC min. 25mA 5VAC min.
6A 250VAC max. - 6A 12VDC max.
12A 380VAC - 16A 250VAC max.
12A 12VDC max.
Contact gap > 1 mm (.039)
Double break 2 x 1,5 mm (.059)
Initial contact resistance : 10mmax. at 1A 4VDC 10mmax. at 1A 4VDC
Insulation resistance : 50 Mmin. 50 Mmin.
Dielectric strength : 750V between open contacts 2KV between open contacts
5KV live to accessible 4KV live to accessible
Electrical life (resistive load) : 50.000 cycles 50.000 cycles
Insulation : Class 2 Class 2
Lamp life :
LED : 60.000 h min. to 75% relative LED : 60.000 h min. to 75 % relative
luminosity - Filament : approx. 5.000 h luminosity - Filament : approx. 5.000 h
Neon : approx. 10.000 h Neon : approx. 10.000 h
Lamp circuit diagrams
GENERAL SPECIFICATIONS
A01 - A1 - A03 A02
Min. mechanical life :
Pushb. momentary : 1 million cycles Pushb. momentary: 1 million cycles
Pushb. maintained : 100.000 cycles Pushb. maintained : 100.000 cycles
Keylock and rotary : 100.000 cycles Keylock and rotary : 100.000 cycles
Panel thickness 8 mm (.315) max. 8 mm (.315) max.
Operating temperature : -20°C to +55°C -20°C to +85°C
Solder heat resistance : 350°C, 5 sec. 350°C, 5 sec.
(IEC 68-2-20Tb, method 2)
Degree of environmental IP 65 front of panel IP 65 front of panel
protection (IEC 529 ) IP 40 back of panel IP 40 back of panel
Lamps : Midget Grooved T13/4, Midget Grooved T13/4,
filament, LED or neon filament, LED or neon
Special multi-LED array
Switch terminals :
Solder/quick-connect 2,8 mm (.110) M3 screws - wire 2 x 0,75 mm2max.
Lamp terminals :
Solder/quick-connect 2,8 mm (.110) M3 screws
Flexible wire 2 x 2,5 mm2max.
Rigid wire 4 mm2max.
Specifications for emergency stop switches : see pages 10 and 22.
For screen engraving or film legends, contact APEM.
A B
A B
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page3
G-4 APEMwww.apem.com
G
A1 series
Engraved aluminium flush mounting pushbuttons and indicators
Panel cut-out Ø 22 (.866)
42.05
(1.655)
8.5
(.335)
18.00
(.709)
18.00
(.709)
14.5
(.571)
Ø25.00
(9.85 DIA)
2.8
(.110)
12.00
(.472)
7.65
(.301)
15.3
(.602)
0.5
(.020)
A pushbutton assembly requires :
engraved screen + lamp (if illuminated) + operator + switch block + flush mount bezel.
To order these elements, select desired model numbers from the table below.
Example : pushbutton, round, illuminated, sealed to IP65, latching, single pole with “start”
engraving, 24V blue LED and flush mounting bezel = A1PCA1X103K403.
3
1
2
01 - Front Fog Lights
02 - Rear Fog Lights
03 - ‘Start’
04 - Interior Light
05 - Boot Release
06 - Hazard Warning
07 - Lights
08 - Heating & Ventilation
09 - Map Lights
10 - Side Lights
11 - ‘Lock’
12 - ‘Unlock’
13 - Rear Window Heating
14 - Cooling
15 - Wipers
16 - Washers
17 - Fan
18 - Horn
19 - Air recirculation
20 - Blank
Engraved Screen Options
A1
Switch Type
P - pushbutton
I - indicator
Accessories
03 - flushmount
Bezel
C - round
Illumination
A - illuminated
B - non-illum.
Sealing
0 - unsealed
1 - sealed IP65
Function
0 - indicator
X - latching
Y - momentary
Switch block
0 - indicator
1 - single pole
2 - double pole
5 - three pole
3 - four pole
Bulb
A1 - filament 6.3V
B1 - filament 14V
C1 - filament 28V
D1 - filament 36V
E1 - filament 48V
F1 - filament 60V
G1 - Neon 110V
H1 - Neon 220V
I1 - Led 6V red
I2 - Led 6V green
I3 - Led 6V amber
J1 - Led 12V red
J2 - Led 12V green
J3 - Led 12V amber
J4 - Led 12V blue
J5 - Led 12V white
K1 - Led 24V red
K2 - Led 24V green
K3 - Led 24V amber
K4 - Led 24V blue
K5 - Led 24V white
L1 - Led 48V red
L2 - Led 48V green
L3 - Led 48V amber
OTHER SCREEN ENGRAVING OPTIONS :
contact APEM.
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page4
APEM www.apem.com G-5
G
A01 series
Illuminated or non-illuminated pushbutton switches
Panel cut-out Ø 16 (.630)
)456.1( )493.(
(.020)
(.709)
(.110)
(.709)
)103.(
)549.(
)QS907.()AID907.(
(.709)
(.236)
(.472)
)533.(
00.0100.24
56.7
05.8
00.81x00.81 00.42Ø 00.81
12.00
6.00
18.00
0.50
18.00
2.80
18.00
)033.( 04.8
(1.209)
)221.1(
(.945)
(.236)
05.82
6.00
24.00
30.70
1 2 3
321
321
1 2 3
321
1 2 3
CD EFC D
)103.( 56.7
)103.( 56.7
(.236)
6.00
)907.( 00.81
16.25
(.640)
9.00
(.354)
9.00
(.354)
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular pushbutton, single pole, maintained, red screen and 12V red LED =
A0161B, A0142M1, A0101X and A0151BUL.
3
1
2
Screen Lamp Operator Switch block
SCREEN ENGRAVING/INSERTABLE LEGENDS : contact APEM
Bezel: rectangular, square, round, ‘Illum’ - illuminated, ‘Non-illum’ - non illuminated
❸❹
UNSEALED SWITCHES (IP40) :
add “01” to end of operator
model number.
BI-COLOUR LED’s optional.
Bezel Colour Part No
black A0161A
red A0161B
amber A0161C
yellow A0161D
green A0161E
blue A0161F
clear A0161G
white A0161J
black A0162A
red A0162B
amber A0162C
yellow A0162D
green A0162E
blue A0162F
clear A0162G
white A0162J
black A0163A
red A0163B
amber A0163C
yellow A0163D
green A0163E
blue A0163F
clear A0163G
white A0163J
Pole Bezel Description Part No
1 or 2 Illum, momentary A0101Y
1 or 2 Illum, maintained A0101X
1 or 2 Non-illum, momentary A0102Y
1 or 2 Non-illum, maintained A0102X
3 or 4 Illum, momentary A0103Y
3 or 4 Illum, maintained A0103X
3 or 4 Non-illum, momentary A0104Y
3 or 4 Non-illum, maintained A0104X
1 or 2 Illum, momentary A0105Y
1 or 2 Illum, maintained A0105X
1 or 2 Non-illum, momentary A0106Y
1 or 2 Non-illum, maintained A0106X
3 or 4 Illum, momentary A0107Y
3 or 4 Illum, maintained A0107X
3 or 4 Non-illum, momentary A0108Y
3 or 4 Non-illum, maintained A0108X
1 or 2 Illum, momentary A0109Y
1 or 2 Illum, maintained A0109X
1 or 2 Non-illum, momentary A0110Y
1 or 2 Non-illum, maintained A0110X
3 or 4 Illum, momentary A0111Y
3 or 4 Illum, maintained A0111X
3 or 4 Non-illum, momentary A0112Y
3 or 4 Non-illum, maintained A0112X
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
No of poles Part No
Single pole A0151B
Double pole A0152B
Three pole A0155B
Four pole A0153B
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page5
G-6 APEMwww.apem.com
G
A01 series
Indicators
Panel cut-out Ø 16 (.630)
An indicator assembly requires :
screen + lamp + operator.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular indicator with red screen and 12V red LED = A0161B, A0142M1
and
A0171.
(.945) (.709) (.709 DIA)
(.709)
18.00
24.00 Ø18.00
18.00
(1.654) (.394)
(.020) (.110)
(.335)
(.330)
10.0042.00
8.40
0.50
8.50
2.80
Screen Lamp Operator
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM
Bezel: rectangular, square, round
UNSEALED INDICATORS (IP40) :
add “01” to end of operator model
number.
Bezel Colour Part No
black A0161A
red A0161B
amber A0161C
yellow A0161D
green A0161E
blue A0161F
clear A0161G
white A0161J
black A0162A
red A0162B
amber A0162C
yellow A0162D
green A0162E
blue A0162F
clear A0162G
white A0162J
black A0163A
red A0163B
amber A0163C
yellow A0163D
green A0163E
blue A0163F
clear A0163G
white A0163J
Bezel Description Part No
Indicator A0171
Indicator A0172
Indicator A0173
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page6
APEM www.apem.com G-7
G
A01 series
Rotary lever switches
Panel cut-out Ø 16 (.630)
(1.654) (.394)
(.020)
(.709)
(.110)
(.709)
(.301)
(.945)
(.709 SQ)
(.709 DIA)
(.709)
(1.209)
(1.122)
(.945)
(.236)
(.472)
10.0042.00
7.65
28.50
18.00x18.00
24.00
Ø18.00
12.00
6.00
18.00
24.00
0.50
18.00
2.80
18.00 30.70
(.330)
8.40
CD
1 2 3
321
321
1 2 3
321
1 2 3
CD EF
A rotary lever switch assembly requires :
operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular rotary switch with long lever, clockwise rotation, single pole,
2 positions, maintained
= A019109 and A0151BUL.
3
1
2
CB
A
Lever Rotation - 2 position switches
The model numbers shown are for switches
with clockwise lever rotation.
For anticlockwise rotation, replace :
09 with 01
10 with 02
11 with 03
12 with 04
at the end of the model number.
Lever Positions
Operator Switch block
Bezel: rectangular, square, round, ‘pos’ - position, ‘mainL - maintained left, ‘momR’ - momentary right, etc
See above photo left.
To order, add “WL” to the end of the operator
part No.
Example : A019609WL..
Optional Engraving on
Lever end
Pole Bezel Description Short lever Long lever
1 or 2 2 pos. maintained A019209 A019109•
1 or 2 2 pos. momentary A019210 A019110•
3 or 4 2 pos. maintained A019211 A019111•
3 or 4 2 pos. momentary A019212 A019112•
1 or 2 3 pos. maintained A019205 A019105
1 or 2 3 pos. momentary A019206 A019106
1 or 2 3 pos. mainL, momR A019207 A019107
1 or 2 3 pos. momL, mainR A019208 A019108
1 or 2 2 pos. maintained A019409 A019309•
1 or 2 2 pos. momentary A019410 A019310•
3 or 4 2 pos. maintained A019411 A019311•
3 or 4 2 pos. momentary A019412 A019312•
1 or 2 3 pos. maintained A019405 A019305
1 or 2 3 pos. momentary A019406 A019306
1 or 2 3 pos. mainL, momR A019407 A019307
1 or 2 3 pos. momL, mainR A019408 A019308
1 or 2 2 pos. maintained A019609 A019509•
1 or 2 2 pos. momentary A019610 A019510•
3 or 4 2 pos. maintained A019611 A019511•
3 or 4 2 pos. momentary A019612 A019512•
1 or 2 3 pos. maintained A019605 A019505
1 or 2 3 pos. momentary A019606 A019506
1 or 2 3 pos. mainL, momR A019607 A019507
1 or 2 3 pos. momL, mainR A019608 A019508
No of poles Part No
Single pole A0151B
Double pole A0152B
Three pole A0155B
Four pole A0153B
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page7
G-8 APEMwww.apem.com
G
A01 series
Keylock switches
Panel cut-out Ø 16 (.630)
Bezel: rectangular, square, round, ‘pos’ - position, ‘mainL - maintained left, ‘momR’ - momentary right, etc
A keylock switch assembly requires :
operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular keyswitch, clockwise rotation, single pole, 2 positions, maintained
= A018125 and A0151BUL
.
3
1
2
C
B
A
Key Rotation - 2 position switches
The model numbers shown are for switches
with clockwise key rotation.
For anticlockwise rotation, replace :
25 with 01
24 with 02
27 with 03
28 with 04
at the end of the model number.
2 standard keys are supplied.
20 key barrel types available.
Operator Switch block
Key Positions
NON-REMOVABLE KEY POSITIONS / ON-ON-ON FUNCTION : contact APEM.
Pole Bezel Description Part No Key removable
1 or 2 2 pos. maintained A018123 A
1 or 2 2 pos. maintained A018125• A-B
1 or 2 2 pos. momentary A018124• A
3 or 4 2 pos. maintained A018127• A-B
3 or 4 2 pos. momentary A018128• A
1 or 2 3 pos. maintained A018105 A-B-C
1 or 2 3 pos. momentary A018106 A
1 or 2 3 pos. mainL, momR A018107 A-B
1 or 2 3 pos. momL, mainR A018108 A-C
1 or 2 2 pos. maintained A018223 A
1 or 2 2 pos. maintained A018225• A-B
1 or 2 2 pos. momentary A018224• A
3 or 4 2 pos. maintained A018227• A-B
3 or 4 2 pos. momentary A018228• A
1 or 2 3 pos. maintained A018205 A-B-C
1 or 2 3 pos. momentary A018206 A
1 or 2 3 pos. mainL, momR A018207 A-B
1 or 2 3 pos. momL, mainR A018208 A-C
1 or 2 2 pos. maintained A018323 A
1 or 2 2 pos. maintained A018325• A-B
1 or 2 2 pos. momentary A018324• A
3 or 4 2 pos. maintained A018327• A-B
3 or 4 2 pos. momentary A018328• A
1 or 2 3 pos. maintained A018305 A-B-C
1 or 2 3 pos. momentary A018306 A
1 or 2 3 pos. mainL, momR A018307 A-B
1 or 2 3 pos. momL, mainR A018308 A-C
No of poles Part No
Single pole A0151B
Double pole A0152B
Three pole A0155B
Four pole A0153B
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page8
APEM www.apem.com G-9
G
A01 series
Emergency stop switches
Panel cut-out Ø 16 (.630)
Ø 60 mm Self
Adhesive Label
(1.654) (1.047)
(.020)
(.709)
(.110)
(.709)
(.602)
(.472)
19.0042.00
15.30
12.00
0.50
18.00
2.80
18.00
(.330)
8.40
C D
(.945 DIA)
Ø24.00
Ø40.00
Prominent 24 mm (.944) dia. or optional 40 mm (1.575) dia. red mushroom actuator
Highly reliable positive break switch
Push to shut off switch, twist to reset to ON
An emergency stop switch assembly requires : operator + switch block.
To order, specify with single pole or double pole positive break switch block.
N.C.
Operator Switch block
Accessory
General specifications
Min. mechanical life : 6.050 cycles (6 cycles per minute)
Operating force / torque : 16 N / 0,1 Nm
Operating temperature : -20°C to +55°C
Solder heat resistance : 350°C, 5 secs (IEC 68-2-2-20Tb, method 2)
Degree of environmental protection (IEC 529) :
IP65 front of panel, IP40 back of panel
Switch terminals : solder/quick-connect 2,8 mm (.110) (IEC 68-2-20)
Electrical specifications
Current/voltage rating :
1,5A 250VAC AC-15
Contact gap : > 3 mm (.118)
Dielectric strength : 2.900V
Electrical life : 6.050 cycles
Option : SP3 version
No of poles Part No
Single pole A0150B
Double pole A0154B
Description Part No
24 mm Ø Emergency stop A01ES
40 mm Ø Emergency stop A01ES SP3
Description Part No
Yellow label with text A01YL1
Yellow label A01YL2
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page9
G-10 APEMwww.apem.com
G
A01 series
Emergency stop switches/mushroom head pushbutton switches
Fitted in enclosures
Prominent 40 mm (1.575) dia. mushroom actuator, twist to release
Highly reliable positive break switching on E-Stop
Sealed to IP65
Robust polycarbonate enclosures
Knockouts for popular conduit sizes
Double pole changeover switch blocks available for momentary/maintained
mushroom head pushbuttons.
N.C.
Technical specifications
Contact rating : Pushbutton switch : 6A 250VAC - E-Stop : 1,5A 250VAC
Dimensions : 65 x 65 x 57 mm
Electrical life : Pushbutton switch : 50 000 cycles - E-Stop : 6 050 cycles
Operating temperature : -20°C to +55°C
3
1
2
Emergency stop
Momentary & maintained
Ø40.0
(1.575 DIA)
65.0 SQUARE
(2.561)
55.0
(2.167)
17.5
(.689)
OPTIONS
12A 250V versions or custom printing on mushroom head actuators : contact APEM.
Description Part No
Emergency stop A01ESSP354B + PEA01
Black momentary A01MMASP352B + PEA01
Red momentary A01MMBSP352B + PEA01
Yellow momentary A01MMDSP352B + PEA01
Green momentary A01MMESP352B + PEA01
Blue momentary A01MMFSP352B + PEA01
Black maintained A01MXASP352B + PEA01
Red maintained A01MXBSP352B + PEA01
Yellow maintained A01MXDSP352B + PEA01
Green maintained A01MXESP352B + PEA01
Blue maintained A01MXFSP352B + PEA01
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page10
APEM www.apem.com G-11
G
A01 series
Mushroom head pushbutton switches
Panel cut-out Ø 16 (.630)
Prominent 24 mm (.944) dia. or optional 40 mm (1.575) dia. mushroom actuators
Momentary and maintained functions
Momentary function versions are unmarked.
Maintained function versions are twist release (arrows indicate direction of twist)
Various coloured mushroom actuators are available.
3
1
2
(1.654) (1.047)
(.020)
(.709)
(.110)
(.709)
19.0042.00
(.945DIA)
Ø24.00
0.50
18.00
2.80
18.00
(.330)
8.40
CD
Ø40.00
(1.575DIA)
OPTION : SP3VERSION
Option : SP3 version
Operator Switch block
No of poles Part No
Single pole A0151B
Double pole A0152B
Three pole A0155B
Four pole A0153B
Actuator Description Part No
24mmØ Black momentary A01MMA
24mmØ Red momentary A01MMB
24mmØ Yellow momentary A01MMD
24mmØ Green momentary A01MME
24mmØ Blue momentary A01MMF
24mmØ Black maintained A01MXA
24mmØ Red maintained A01MXB
24mmØ Yellow maintained A01MXD
24mmØ Green maintained A01MXE
24mmØ Blue maintained A01MXF
40mmØ Black momentary A01MMA SP3
40mmØ Red momentary A01MMB SP3
40mmØ Yellow momentary A01MMD SP3
40mmØ Green momentary A01MME SP3
40mmØ Blue momentary A01MMF SP3
40mmØ Black maintained A01MXA SP3
40mmØ Red maintained A01MXB SP3
40mmØ Yellow maintained A01MXD SP3
40mmØ Green maintained A01MXE SP3
40mmØ Blue maintained A01MXF SP3
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page11
G-12 APEMwww.apem.com
G
A1-A01 series
Industrial controls
Accessories
FLAPGUARDS
FLUSH MOUNTING BEZELS Dark grey plastic material - supplied with sealing washer
Rectangular A01FG1
Rectangular A01FM1 Square A01FM Round A01FM2
Square/round A01FG2
(.537)
13.65
24.00
(.945)
12.00
(.472) 13.50
(.531)
24.00
(.945)
(.531)
(.537)
13.65
(.945)
24.00
(.354)
9.00 13.50
(.708)
18.00
12.00
(.472)
20.60
(.811 )
+0.20
0.00
.000
+.008
(1.051 )
26.70
(1.173)
29.80
+0.20
0.00
.000
+.008
20.40
(.712)
18.10
(.803)
(.630DIA)
Ø16.00
23.80
(.937)
FLUSH MOUNTING BEZELS Metal versions
Round, anodised aluminium A01FMM
Round, matt black A01FMMG
+.008
(.874 )
22.20
11.00
(.433)
(.715)
18.15
(.866 DIA)
Ø22.00
0.00
.000
+0.20
(.630DIA)
Ø16.00
(.984 DIA)
Ø25.00
+.008
(.811 )
.000
20.60 0.00
+0.20
(.472)
12.00 (.937)
23.80
20.40
(.712)
18.10
(.803)
(.937)
23.80
(.630DIA)
Ø16.00
+.008
(.874 )
22.20
11.00
(.433)
(.715)
18.15
(.866 DIA)
Ø22.00
0.00
.000
+0.20
(.630DIA)
Ø16.00
(.984 DIA)
Ø25.00
5.00
(.196)
10.25
(.403)
18.40
(.724)
7.65
(.301)
7.65
(.301)
1.10
(.043)
4.25
(.167)
4.25
(.167)
0.80
(.031)
6.00
(.236)
18.25
(.719)
6.00
(.236)
Single pole, non illuminated A01PC1
Double pole, non illuminated A01PC2
Single pole, illuminated A01PC3
Double pole, illuminated A01PC4
Indicator A01PC5
Single pole, E-stop A01PC6
Double pole, E-stop A01PC7
PCB SOCKET
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page12
APEM www.apem.com G-13
G
A1-A01 series
Industrial controls
Accessories
Ø16.00
(.629DIA)
18.00
(.708)
2.00
(.078)
18.00
(.708)
14.75
(.580)
ANTI ROTATION RING Recommended to prevent product rotation
Resistor assembly - 2 stage illumination
A01LW
METAL GUARDS Slot as alternative to Ø 2 mm hole - Material : 1 mm thick aluminium.
Rectangular A01MG1 Square A01MG Round, natural A01MG2
Matt black A01MG2G
(.630DIA)
Ø16.00
(.944)
24.00
(.399)
10.15
Ø2.00
(.078DIA)
(.708)
18.00
(.472)
12.00
SWITCHBLOCK TERMINAL GUARDS
2 way A01RTC2 8 way A01RTC8
18.00
(.717)
18.20
(.630DIA)
Ø16.00
(.708) 12.00
(.472)
(.712 DIA)
Ø18.10
Ø16.05
(.350)
8.90
9.80
(.385)
Ø19.60
(.771 DIA)
(.631DIA)
(.289)
(.413)
10.50
(.393)
10.00
20.75
(.816)
14.85
(.584)
7.35
(.236)
20.75
(.393)(.413)
(.816)
10.50
20.75
(.816)
7.45
10.00
8.50
(.334)
(.293)
6.00
Ø18.0
(.709 DIA) 18.0
(.709)
18.0
(.709)
18.0
(.709)
24.0
(.946)
BLANKING PLUGS
Round A0133 Square A0132 Rectangular A0131
RESISTOR ASSEMBLY
A0152B + RISSP
(DIM) normally closed (BRIGHT) normally open
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page13
G-14 APEMwww.apem.com
G
A1-A01 series
Industrial controls
Installation - tools
Modular construction / panel mounting
SWITCH BLOCK
FIXING
NUT
PANEL
BULB
REFLECTOR
LOCATING
SLOT
LEGEND
SCREEN
EMERGENCY
STOP
ROTARY
LEVER SWITCHES
KEYLOCK
SWITCHES
PUSHBUTTONS
& INDICATORS
LATCH
OPERATOR
(.157 MAX)
4.00 Maxi
SEAL
POLARISING
DOT
PANEL CUT-OUT
Round & square operators only
Rectangular operators only
Max. panel thickness : 8 mm (.315)
PANEL MOUNTING ASSEMBLY
Drill/punch hole shaped as above.
Assemble front operator through hole, fit fixing nut and
tighten to a maximum torque of 0,8Nm using tool
No 30-0001.
Wire chosen switch block as required and slide onto
operator until latch engages.
Fit bulb if required using tool No 30-0002.
Snap screen onto reflector assembly with legend in
between if required and snap onto front operator TAKING
CARE TO LINE UP THE LOCATING SLOT WITH THE
POLARISING DOT, and not to damage the seal.
TO REMOVE BULB
Remove reflector/screen assembly. Use the bulb extractor
30-0002 to remove the bulb.
SWITCH BLOCK
To assemble switch block to front operator, TAKE CARE
TO LINE UP SWITCH BLOCK WITH FRONT OPERATOR.
Once in position, slide on to front operator. NB. : Ensure
latch is fully engaged correctly onto the switch block.
To remove switch block, depress the latch and slide the
switch block off the operator.
(.059)
(.285)
1.50
Ø16.00
.000/+.011
0.00/+0.30
(.629 DIA )
7.25
(.413)
(.078 DIA)
Ø2.00
10.50
(.629 DIA )
0.00/+0.30
.000/+.011
Ø16.00
FIXING NUT KEY
30-0001
BULB REMOVER
30-0002
01-Series A01_A1-A-R1_01-Series A01_A1-A 06/11/14 14:56 Page14
APEM www.apem.com G-15
G
A02 series
Illuminated or non-illuminated pushbutton switches
Panel cut-out Ø 22 (.866) or 29,5 x 21,5 (1.160x.846)
(.394)(2.185)
(1.319) (.827)
(.394)
(2.520)(1.062)
(2.520) (.394)
(.827)
(1.142)
(1.319)
(1.417)
(1.142 SQ)
(1.142 DIA)
(.945)
10.0055.50
24.00
10.00
64.0027.00
29.00x29.00
Ø29.00
64.00 10.00
29.00
36.00
33.50 21.00
21.00
33.50
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 illuminated rectangular maintained pushbutton, switch block with 2 N.O. contacts,
red screen and 12V red LED assembly = A0261B, A0242J1, A0201X and A02503UL.
N.C.
N.O. N.O./N.C.
Screen Lamp Operator Switch block
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel: rectangular, square, round, ‘Illum’ - illuminated, ‘Non-illum’ - non illuminated
Second switch block
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
Bezel Colour Part No
black A0261A
red A0261B
amber A0261C
yellow A0261D
green A0261E
blue A0261F
clear A0261G
white A0261J
black A0262A
red A0262B
amber A0262C
yellow A0262D
green A0262E
blue A0262F
clear A0262G
white A0262J
black A0263A
red A0263B
amber A0263C
yellow A0263D
green A0263E
blue A0263F
clear A0263G
white A0263J
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
Bezel Description Lamp type Part No
Illum, momentary Lamp/LED A0201Y
Illum, maintained Lamp/LED A0201X
Non-illum, maintained A0203X
Non-illum, momentary A0203Y
Illum, momentary Lamp/LED A0204Y
Illum, maintained Lamp/LED A0204X
Non-illum, momentary A0206Y
Non-illum, maintained A0206X
Illum, momentary Lamp/LED A0207Y
Illum, maintained Lamp/LED A0207X
Non-illum, momentary A0209Y
Non-Illum, maintained A0209X
The company reserves the right to change specifications without notice.
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page15
UG1410A
G-16 APEMwww.apem.com
G
A02 series
Metal bezel pushbutton switches and indicators
Panel cut-out Ø 22 (.866)
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel: rectangular, square, round, ‘Illum’ - illuminated, ‘Non-illum’ - non illuminated
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + one or two switch blocks.
An indicator assembly requires : screen + lamp + operator
To order these elements, select desired model numbers from tables below.
Example : IP65 illuminated metal bezel maintained pushbutton, switch block with 2 N.O. contacts,
red screen and 12V red LED assembly = A0263B, A0244J1, A0211X and A02503UL.
N.C.
N.O. N.O./N.C.
❸❹
Screen Lamp Operator Switch block
Second switch block
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
Std bezel material : nickel plated brass.
For optional black finish, add “G” to the end of
operator model number.
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
(.452)
11.50
(2.952)
75.00
(1.791)
45.50
(1.142DIA)
Ø29.00
(1.338)
34.00 (.826)
21.00
(1.142DIA)
Ø29.00
Bezel Colour Part No
black A0263A
red A0263B
amber A0263C
yellow A0263D
green A0263E
blue A0263F
clear A0263G
white A0263J
Bezel Description Lamp type Part No
Illum, momentary Lamp/LED A0210Y
Illum, maintained Lamp/LED A0210X
Non-illum, momentary A0212Y
Non-illum, maintained A0212X
Illum, indicator Lamp/LED A0277
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page16
APEM www.apem.com G-17
G
A02 series
Flush mounting pushbutton switches and indicators
Panel cut-out Ø 30 (1.181)
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + one or two switch blocks.
An indicator assembly requires : screen + lamp + operator
To order these elements, select desired model numbers from tables below.
Example : IP65
illum. flush mounting maintained pushbutton, switch block with 2 N.O. contacts
,
red screen and 12V red LED assembly = A0263B, A0244J1, A0213X and A02503UL.
N.C.
N.O. N.O./N.C.
❸❹
Screen Lamp Operator Switch block
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel: rectangular, square, round, ‘Illum’ - illuminated, ‘Non-illum’ - non illuminated
Second switch block
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
Std bezel material : silver anodised aluminium.
For optional black anodised aluminium, add “G”
to end of operator model number.
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
(1.338) (.826) (1.181)
(.078)
2.00
(2.874)
73.00
34.00 21.00
(1.811)
46.00
(1.378DIA)
Ø35.00
30.00
DECOUPE DU PANNEAU
(1.378DIA)
Ø35.00
PANEL CUT-OUT
Bezel Colour Part No
black A0263A
red A0263B
amber A0263C
yellow A0263D
green A0263E
blue A0263F
clear A0263G
white A0263J
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
Bezel Description Lamp type Part No
Illum, momentary Lamp/LED A0214Y
Illum, maintained Lamp/LED A0214X
Non-illum, momentary A0215Y
Non-illum, maintained A0215X
Illum, indicator Lamp/LED A02791
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page17
G-18 APEMwww.apem.com
G
A02 series
Indicators
Panel cut-out Ø 22 (.866) or 29,5 x 21,5 (1.160x.846)
An indicator assembly requires :
Screen + lamp, LED or LED assembly + operator.
To order these elements, select desired model numbers from tables below.
Example : IP65 rectangular indicator with red screen and 12V red LED assembly = A0261B, A0242J1 and A0272.
(1.142)
(1.417)
(1.142 SQ)
(1.142 DIA)
(.945)
24.00
29.00x29.00
Ø29.00
29.00
36.00
33.50
(1.319)
33.50
(1.319)
(.827)
21.00
(.827)
21.00
10.00
(.394)
10.00
(.394) (1.142)
29.00
37.50
(1.476)
Screen Lamp Operator
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel: rectangular, square, round,
UNSEALED INDICATORS (IP40) :
add “01” to end of operator model number.
Bezel Description Lamp type Part No
Indicator Lamp/LED A0271
Indicator Lamp/LED A0273
Indicator Lamp/LED A0275
Bezel Colour Part No
black A0261A
red A0261B
amber A0261C
yellow A0261D
green A0261E
blue A0261F
clear A0261G
white A0261J
black A0262A
red A0262B
amber A0262C
yellow A0262D
green A0262E
blue A0262F
clear A0262G
white A0262J
black A0263A
red A0263B
amber A0263C
yellow A0263D
green A0263E
blue A0263F
clear A0263G
white A0263J
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page18
APEM www.apem.com G-19
G
A02 series
Rotary switches
Panel cut-out Ø 22 (.866)
(.827)
(2.520)(1.062)
(2.520)
(1.142)
(1.319)
64.0027.00
64.00
29.00
21.00
33.50
20.00
(.787)
29.00x29.00
(1.142 SQ)
Ø29.00
(1.142 DIA)
22.00
(.866)
22.00
(.866)
A rotary lever assembly requires :
operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 square 2 position maintained rotary switch with long lever, clockwise rotation,
switch block with 2 N.O. contacts = A029107 and A02503UL.
N.C.
N.O. N.O./N.C.
CB
A
Lever Rotation - 2 position switches
The model numbers shown are for switches
with clockwise lever rotation.
For anticlockwise rotation, replace :
07 with 01
08 with 02
at the end of the model number.
To order, add “WL” to the end of the part No.
Example : A029407WL.
Operator Switch block
Bezel: square, round,
Lever positions
Optional engraving
on lever end
Second switch block
To achieve 3 or 4 pole switching,
add second switch block, from
above table.
OPTION
To specify flush mounting 30 mm) option,
add “FM” to the end of the part number (for
round operators only).
Example : A029407FM.
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Bezel Description Short lever Long lever
2 pos. maintained A029207 A029107•
2 pos. momentary A029208 A029108•
3 pos. maintained A029203 A029103
3 pos. momentary A029204 A029104
3 pos. mainL, momR A029205 A029105
3 pos. momL, mainR A029206 A029106
2 pos. maintained A029407 A029307•
2 pos. momentary A029408 A029308•
3 pos. maintained A029403 A029303
3 pos. momentary A029404 A029304
3 pos. mainL, momR A029405 A029305
3 pos. momL, mainR A029406 A029306
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page19
G-20 APEMwww.apem.com
G
A02 series
Keylock switches
Panel cut-out Ø 22 or 29,5 x 21,5
C
B
A
(.827)
(2.520)(1.062)
(1.142)
(1.319)
64.0027.00
29.00
21.00
33.50
29.00x29.00
(1.142 SQ)
Ø29.00
(1.142 DIA)
33.50
(1.319) 21.00
(.827)
34.50
(1.358)
(1.496)
38.00
55.50
(2.185)
24.00
(.945)
36.00
(1.417)
A keyswitch assembly requires :
operator + one or two switch blocks.
To order these elements, select desired model numbers from tables below.
Example : IP65 square 2 position keyswitch, clockwise rotation, switch block with 2 N.O.
contacts = A028220 and A02503UL.
N.C.
N.O. N.O./N.C.
Key Rotation - 2 position switches
The model numbers shown are for switches
with clockwise key rotation.
For anticlockwise rotation, replace:
20 with 01
19 with 02
at the end of the model number
2 standard keys are supplied.
20 key barrel types available.
Non-removable key positions : contact
APEM.
Operator Switch block
Bezel: rectangular, square, round,
Second switch block
To achieve 3 or 4 pole switching,
add second switch block, from
above table
Key positions
OPTION
To specify flush mounting 30 mm) option,
add “FM” to the end of the part number (for
round operators only). Example : A028320FM.
Bezel Description Part No Key removable
in positions
2 pos. maintained A028120• A-B
2 pos. momentary A028119• A
3 pos. maintained A028105 A-B-C
3 pos. momentary A028106 A
3 pos. mainL, momR A028107 A-B
3 pos. momL, mainR A028108 A-C
2 pos. maintained A028220• A-B
2 pos. momentary A028219• A
3 pos. maintained A028205 A-B-C
3 pos. momentary A028206 A
3 pos. mainL, momR A028207 A-B
3 pos. momL, mainR A028208 A-C
2 pos. maintained A028320• A-B
2 pos. momentary A028319• A
3 pos. maintained A028305 A-B-C
3 pos. momentary A028306 A
3 pos. mainL, momR A028307 A-B
3 pos. momL, mainR A028308 A-C
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page20
APEM www.apem.com G-21
G
A02 series
Emergency stop switches
Panel cut-out Ø 22 (.866)
(.827)
(2.520)
(1.142)
64.00
29.00
21.00
21.00
(.827)
Ø40.00
(1.575 DIA)
Prominent 40 mm (1.575) dia. red mushroom actuator
Highly reliable positive break switch
Push to shut off switch, twist to reset to ON
An emergency stop switch assembly requires : operator + switch block.
To order, specify with single pole or double pole positive break switch block.
N.C.
Operator Switch block
General specifications
Mechanical life : 6.050 cycles (6 cycles per minute)
Operating force : 20 N
Operating temperature : -20°C to +85°C
Degree of environ. protection (IEC529) : IP65 front of panel,
IP40 back of panel
Switch terminals : M3 screws - wire 2x0.75mm2max.
Electrical specifications
Current/voltage rating :
2,5A 380VAC AC-15
Contact gap : > 3 mm (.118)
Dielectric strength : 2.500V
Electrical life : 6.050 cycles
Accessory 90 mm Ø Self
Adhesive Label
Description Part No
Yellow label with text A02YL1
Yellow label A02YL2
EMERGENCY STOP SWITCH ENCLOSURE
To order the Emergency Stop Switch in the Plastic Enclosure
(94 x 94 x 81 mm) with a 2 pole Positive Break Switch Block and Emergency
Stop label, use Part number : A02PE2L.
Bezel Description Part No
Emergency stop A02ES
No of poles Part No
Double pole A02511
Single pole A02512
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page21
G-22 APEMwww.apem.com
G
A02 series
Mushroom head pushbutton switches
Panel cut-out Ø 22 (.866)
Prominent 40 mm (1.575) dia. mushroom actuator or optional 26 mm (1.024) actuator
Momentary and maintained functions
Momentary function versions are unmarked
Maintained function versions are twist to release (arrows indicate direction of twist)
Various coloured mushroom actuators are available
N.C.
N.O. N.O./N.C.
(.827)
(2.520)
(1.142)
64.00
29.00
21.00
21.00
(.827)
Ø40.00
(1.575 DIA)
Operator Switch block
Bezel Description Part No
Black momentary A02MMA
Red momentary A02MMB
Yellow momentary A02MMD
Green momentary A02MME
Blue momentary A02MMF
Black maintained A02MXA
Red maintained A02MXB
Yellow maintained A02MXD
Green maintained A02MXE
Blue maintained A02MXF
Contacts Part No
1 N.O. A02501
1 N.C. A02502
2 N.O. A02503
2 N.C. A02504
1 N.O./1 N.C. A02505
Second switch block
Contacts Part No
1 N.O. A02506
1 N.C. A02507
2 N.O. A02508
2 N.C. A02509
1 N.O./1 N.C. A02510
To achieve 3 or 4 pole switching,
add second switch block, from
above table
OPTION
For optional reduced 26 mm) mushroom
head operators : contact APEM.
Bezel: round
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page22
APEM www.apem.com G-23
G
A02 series
Industrial controls
Installation
Modular construction / panel mounting
PANEL CLAMP
END CAP
SWITCH BLOCK
ADAPTOR BLOCK
OPERATOR
FIXING
NUT
(.236 MAX)
6.00 Maxi
PANEL
SEAL
BULB
POLARISING
DOT
REFLECTOR
LEGEND
LOCATING
SLOT
SCREEN
FIXING SCREW
EMERGENCY
STOP
ROTARY
LEVERS SWITCHES
KEYLOCK
SWITCHES
PUSHBUTTONS & INDICATORS
PANEL CUT-OUT
Round & square operators
Rectangular operators
Max. panel thickness : 8 mm (.315)
PANEL MOUNTING ASSEMBLY
Drill/punch hole in panel as shaped above.
Assemble front operator through hole and :
a/ Round & square types : tighten nut to a maximum
torque of 0,8Nm using tool No 30-0001. Snap on
adaptor block
b/ Rectangular types : tighten two panel fixing screws in
front to a maximum torque of 0,06Nm.
Wire chosen switch block as required and snap onto
front operator.
Snap end cap onto switch block.
Fit bulb if required using tool No 30-0002.
Snap screen onto reflector assembly with legend in
between if required ans snap into front operator TAKING
CARE TO LINE UP THE LOCATING SLOT WITH THE
POLARISING DOT, and not to damage the seal.
TO REMOVE BULB
Remove reflector/screen assembly. Use the bulb extractor
30-0002 to remove the bulb.
TO REMOVE SWITCH BLOCK
Lever out latches using small screwdriver taking care not to
overbend, and pull off the block from the front operator.
(.511)
(.118)
13.00
3.00
0.00/+0.50
Ø22.00
(.866 DIA )
.000/+.019
.000/+.019
(1.161 )
29.50 0.00/+0.50
(.846 )
21.50 0.00/+0.50
.000/+.019
A02 Accessories
Part No : 14-0005
End cap terminal guard offering unique terminal protection.
6.35 mm push on tab terminals.
Specify “SP” to the end of the switchblock and operator P/N.
Example : A02503SP.
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page23
G-24 APEMwww.apem.com
G
A03 series
Illuminated or non-illuminated pushbutton switches and indicators
Panel cut-out Ø 22 (.866) or 30 (1.181) - Plastic or metal flush mounting bezel
A pushbutton assembly requires :
screen + lamp (if illuminated) + operator + switch block.
To order these elements, select desired model numbers from tables below.
Example : IP65 flush mounting round pushbutton, maintained function, red screen, 12V red LED
and single pole switch block = A0314X, A0263B, A0142M1 and A0151BUL.
3
1
2
Ø29.00
(1.143 DIA)
10.00
(.394)
26.00
(1.024)
49.00
(1.931)
59.00
(2.325)
6.00
(.236)
6.00
(.236)
7.65
(.301)
18.00
(.709)
18.00
(.709)
0.50
Ø35.00
(1.379 DIA)
2.00
(.079)
59.50
(2.344)
1.0 to 6.0
Panel Thickness
Screen Lamp Operator Switch block
❸❹
Bezel Colour Part No
black A0263A
red A0263B
amber A0263C
yellow A0263D
green A0263E
blue A0263F
clear A0263G
white A0263J
Lamp Voltage Part No
Filament 6.3V A0141A
Filament 14V A0141B
Filament 28V A0141C
Filament 36V A0141D
Filament 48V A0141E
Filament 60V A0141F
Neon 110V A0143G
Neon 220V A0143H
LED 6V red A0142L1
LED 6V green A0142L2
LED 6V amber A0142L3
LED 12V red A0142M1
LED 12V green A0142M2
LED 12V amber A0142M3
LED 12V blue A0142M4
LED 12V white A0142M5
LED 24V red A0142N1
LED 24V green A0142N2
LED 24V amber A0142N3
LED 24V blue A0142N4
LED 24V white A0142N5
LED 48V red A0142P1
LED 48V green A0142P2
LED 48V amber A0142P3
No of poles Part No
Single pole A0151B
Double pole A0152B
Three pole A0155B
Four pole A0153B
Bezel Description Lamp type Part No
Plastic illum, momentary Lamp/LED bulb A0307Y
Plastic illum, maintained Lamp/LED bulb A0307X
Plastic non-illum, momentary A0309Y
Plastic non-illum, maintained A0309X
Metal illum, momentary Lamp/LED bulb A0310Y
Metal illum, maintained Lamp/LED bulb A0310X
Metal non-illum, momentary A0312Y
Metal non-illum, maintained A0312X
F/mount illum, momentary Lamp/LED bulb A0314Y
F/mount illum, maintained Lamp/LED bulb A0314X
F/mount non-illum, momentary A0315Y
F/mount non-illum, maintained A0315X
Plastic indicator A0375
Metal indicator A0377
F/mount indicator A03791
UNSEALED SWITCHES (IP40) :
add “01” to end of operator model number.
SCREEN ENGRAVING / INSERTABLE LEGENDS : contact APEM.
Bezel: round. ‘Illum’ - illuminated, ‘Non-illum’ - non illuminated
02-Serie A02_A03-A-R1_02-Serie A02_A03-A 06/11/14 14:49 Page24