DFM 14 Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ030, Schematics A (11), B (12), J (15) FEATURES * 11, 12, 15 Schematics; hot-solder dipped * MIL-PRF-83401 qualified * Highly stable thick film * TCR available in "K" ( 100ppm/C) or "M" ( 300ppm/C) characteristic * 100% screen tested per Group A, Subgroup 1 of MIL-PRF-83401 * 0.065" [1.65mm] height for high density packaging STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING P P 70C DFM 70C CIRCUIT LIMITING ELEMENT TEMPERATURE1) STANDARD2) RESISTANCE SCHEMATIC VOLTAGE COEFFICIENT TOLERANCE RANGE ELEMENT PACKAGE MAX W W V ppm/C % 0.050 0.350 11 50 "K" = 100 / "M" = 300 2 10R0 - 1M0 0.025 0.325 12 50 "K" = 100 / "M" = 300 2 10R0 - 1M0 0.015 0.350 15 50 "K" = 100 / "M" = 300 2 see table 1) Temperature Range: - 55C to + 125C 2) 1% and 5% tolerance available 11 Schematic 12 Schematic 15 Schematic Power Rating (Watts) Power Rating (Watts) Power Rating (Watts) * Consult factory for stocked values 0.400 DFM14-11 Package 0.350 0.200 0.400 DFM14-12 Package 0.325 Single Resistor 0.025 - 55 0.350 Single Resistor 0.050 + 25 + 70 + 125 + 150 Ambient Temperature C - 55 DFM14-15 Package 0.200 0.200 Single Resistor 0.400 0.015 + 25 + 70 + 125 + 150 Ambient Temperature C - 55 + 25 + 70 + 125 + 150 Ambient Temperature C Derating www.vishay.com 124 For Technical Questions, contact: ff2aresistors@vishay.com Document Number: 31517 Revision 06-Aug-02 DFM 14 Vishay Dale Thick Film Resistor Networks, Flat Pack DIMENSIONS in inches [millimeters] Pin #1 0.050 [1.27] Typ. 0.250 [6.35] Min. 0.365 [9.27] Min. 0.385 [9.78] Max. 0.250 [6.35] Min. 0.075 [1.91] Max. 0.019 0.006 [0.483 0.15] 0.005 + 0.004 - 0.002 [0.127 + 0.102 - 0.051] 0.825 [20.96] Max. 0.305 [7.75] Max. ORDERING INFORMATION - MILITARY PART NUMBER 11 SCHEMATIC 12 SCHEMATIC 15 SCHEMATIC M8340103 M8340103 M8340103 DETAIL SPEC. NO. M8340103 =14 Pin Flat Pack RZ030 EXAMPLE: M8340103M6801GA = A flat pack resistor network with 14 pins, a TCR of 300ppm/C, resistance value of 6.8k ohm, tolerance of 2% and to schematic "A". M M K CHARACTERISTIC "K" = 100ppm/C "M" = 300ppm/C G G G TOLERANCE 6801 6801 A001* RESISTANCE VALUE F = 1% G = 2% J = 5% The first three digits are significant figures and the last digit specifies the number of zeros to follow = 11 and 12 schematics. For 15 schematic see footnote (*). EXAMPLE: M8340103M6801GB = A flat pack resistor network with 14 pins, a TCR of 300ppm/C, resistance value of 6.8k ohm, tolerance of 2% and to schematic "B". A B J SCHEMATIC EXAMPLE: M8340103KA001GJ = A flat pack resistor network with 14 pins, a TCR of 100ppm/C, R1 resistance value of 82 ohm, R2 resistance value of 130 ohm, tolerance of 2% and schematic "J". DFM14-11, 12, 15 = Type G (hot-solder dipped). Hot-solder dipped leads supplied as standard finish. * The J-schematic resistance values are specified by a 4-digit code, which comes from MIL-PRF-83401. The codes and corresponding resistance values are: CODE A001 A002 A003 A004 A005 A006 A007 A008 A009 Document Number: 31517 Revision 06-Aug-02 R1 (Ohms) 82 120 130 160 180 180 220 220 330 R2 (Ohms) 130 200 210 260 240 390 270 330 390 CODE A010 A011 A012 A013 A014 A015 A016 A017 A018 R1 (Ohms) 330 330 1.5k 3k 180 270 560 560 620 R2 (Ohms) 470 680 3.3k 6.2k 270 270 560 1.2k 2.7k For Technical Questions, contact: ff2aresistors@vishay.com www.vishay.com 125 DFM 14 Thick Film Resistor Networks, Flat Pack Vishay Dale CIRCUIT APPLICATIONS 11 Schematic DFM14-11 (M8340103xxxxxxA) 7 isolated resistors The DFM14-11 provides the user with 7 nominally equal resistors with each resistor isolated from all others. Commonly used in the following applications: * "Wired OR" Pull-up * Power Driven Pull-up * TTL Input Pull-down DFM14-11 Pin #1 * Line Termination * LED Current Limiting * ECL Output Pull-down * Power Gate Pull-up * Long-line Impedance balancing 12 Schematic DFM14-12 (M8340103xxxxxxB) 13 resistors with one pin common * * * * * * * The DFM14-12 provides the user with a choice of 13 nominally equal resistors, each connected to a common pin. Commonly used in the following applications: * MOS/ROM Pull-up/ * Pull-down * Open Collector Pull-up DFM14-12 Pin #1 * "Wired OR" Pull-up * Power Driven Pull-up * TTL Unused Gate Pull-up * Digital Pulse Squaring * TTL Input Pull-down * High Speed Parallel Pull-up 15 Schematic 14 R1 R1 R2 R1 R2 1 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R2 R1 R2 DFM14-15 (M8340103xxxxxxJ) 12 pairs of resistors The DFM14-15 provides the user with a choice of 12 pairs of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. DFM14-15 www.vishay.com 126 For Technical Questions, contact: ff2aresistors@vishay.com Document Number: 31517 Revision 06-Aug-02 DFM 14 Thick Film Resistor Networks, Flat Pack Vishay Dale MECHANICAL SPECIFICATIONS Marking Resistance to Solvents Permanency testing per MIL-PRF-83401 Solderability Per MIL-PRF-83401. Terminals Per MIL-STD-1276 DFM14-11, 12, 15 = Type G (hot solder dipped) Hot solder dipped leads supplied as standard finish. Body Epoxy filled ceramic sandwich PERFORMANCE TEST CONDITIONS MAX. R (Typical Test Lots) Power Conditioning 1.5 x rated power, applied 1.5 hours "ON" and 0.5 hours "OFF" for 100 hours 4 hours at + 25C ambient temperature 0.50% R Thermal Shock 5 cycles between - 65C and + 125C 0.50% R Short Time Overload 2.5 x rated working voltage, 5 seconds 0.25% R (Char. K) 0.50% R (Char. M) Low Temperature Operation 45 minutes at full rated working voltage at - 65C 0.25% R (Char. K) 0.50% R (Char. M) Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH 0.50% R Resistance to Soldering Heat Leads immersed in + 260C solder to within 1/16" of body for 10 seconds 0.25% R Shock Total of 18 shocks at 100 g's 0.25% R Vibration 12 hours at maximum of 20 g's between 10 and 2,000 Hz 0.25% R Load Life 1000 hours at + 70C, rated power applied 1.5 hours "ON", 0.5 hour "OFF" for full 1000 hour period 0.50% R (Char. K) 2.0% R (Char. M) Terminal Strength 1.5 pound pull for 30 seconds 0.25% R Insulation Resistance 10,000 Megohm (minimum) Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) Document Number: 31517 Revision 06-Aug-02 For Technical Questions, contact: ff2aresistors@vishay.com www.vishay.com 127