54F/74F573 Octal D-Type Latch with TRI-STATEE Outputs General Description Features The 'F573 is a high speed octal latch with buffered common Latch Enable (LE) and buffered common Output Enable (OE) inputs. This device is functionally identical to the 'F373 but has different pinouts. Y Y Y Y Y Commercial Inputs and outputs on opposite sides of package allowing easy interface with microprocessors Useful as input or output port for microprocessors Functionally identical to 'F373 TRI-STATE outputs for bus interfacing Guaranteed 4000V minimum ESD protection Package Number Military 74F573PC 54F573DM (Note 2) Package Description N20A 20-Lead (0.300x Wide) Molded Dual-In-Line J20A 20-Lead Ceramic Dual-In-Line 74F573SC (Note 1) M20B 20-Lead (0.300x Wide) Molded Small Outline, JEDEC 74F573SJ (Note 1) M20D 20-Lead (0.300x Wide) Molded Small Outline, EIAJ 54F573FM (Note 2) W20A 20-Lead Cerpak 54F573LM (Note 2) E20A 20-Lead Ceramic Leadless Chip Carrier, Type C Note 1: Devices also available in 13x reel. Use suffix e SCX and SJX. Note 2: Military grade device with environmental and burn-in processing. Use suffix e DMQB, FMQB and LMQB. Logic Symbols Connection Diagrams Pin Assignment for DIP, SOIC and Flatpak Pin Assignment for LCC TL/F/9566-1 IEEE/IEC TL/F/9566 - 3 TL/F/9566 - 2 TL/F/9566-4 TRI-STATEE is a registered trademark of National Semiconductor Corporation. C1995 National Semiconductor Corporation TL/F/9566 RRD-B30M115/Printed in U. S. A. 54F/74F573 Octal D-Type Latch with TRI-STATE Outputs August 1995 Unit Loading/Fan Out 54F/74F Pin Names D 0 - D7 LE OE O0 - O7 Description U.L. HIGH/LOW Input IIH/IIL Output IOH/IOL Data Inputs Latch Enable Input (Active HIGH) TRI-STATE Output Enable Input (Active LOW) TRI-STATE Latch Outputs 1.0/1.0 1.0/1.0 20 mA/b0.6 mA 20 mA/b0.6 mA 1.0/1.0 20 mA/b0.6 mA 150/40(33.3) b 3 mA/24 mA (20 mA) Functional Description The 'F573 contains eight D-type latches with 3-state output buffers. When the Latch Enable (LE) input is HIGH, data on the Dn inputs enters the latches. In this condition the latches are transparent, i.e., a latch output will change state each time its D input changes. When LE is LOW the latches store the information that was present on the D inputs a setup time preceding the HIGH-to-LOW transition of LE. The 3state buffers are controlled by the Output Enable (OE) input. When OE is LOW, the buffers are in the bi-state mode. When OE is HIGH the buffers are in the high impedance mode but this does not interfer with entering new data into the latches. Function Table Inputs Outputs OE LE D O L L L H H H L X H L X X H L O0 Z H e HIGH Voltage Level L e LOW Voltage Level X e Immaterial O0 e Value stored from previous clock cycle Logic Diagram TL/F/9566 - 5 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 2 Absolute Maximum Ratings (Note 1) Recommended Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Storage Temperature b 65 C to a 150 C Ambient Temperature under Bias Junction Temperature under Bias Plastic b 55 C to a 125 C Free Air Ambient Temperature Military Commercial b 55 C to a 125 C 0 C to a 70 C Supply Voltage Military Commercial b 55 C to a 175 C b 55 C to a 150 C a 4.5V to a 5.5V a 4.5V to a 5.5V VCC Pin Potential to Ground Pin b 0.5V to a 7.0V b 0.5V to a 7.0V Input Voltage (Note 2) b 30 mA to a 5.0 mA Input Current (Note 2) Voltage Applied to Output in HIGH State (with VCC e 0V) b 0.5V to VCC Standard Output b 0.5V to a 5.5V TRI-STATE Output Current Applied to Output in LOW State (Max) twice the rated IOL (mA) ESD Last Passing Voltage (Min) 4000V Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. DC Electrical Characteristics Symbol 54F/74F Parameter Min VIH Input HIGH Voltage VIL Input LOW Voltage VCD Input Clamp Diode Voltage VOH Output HIGH Voltage Typ Units 2.0 54F 10% VCC 54F 10% VCC 74F 10% VCC 74F 10% VCC 74F 5% VCC 74F 5% VCC VCC Conditions Max V Recognized as a HIGH Signal 0.8 V Recognized as a LOW Signal b 1.2 V 2.5 2.4 2.5 2.4 2.7 2.7 Min IIN e b18 mA V Min IOH IOH IOH IOH IOH IOH IOL e 20 mA IOL e 24 mA e e e e e e b 1 mA b 3 mA b 1 mA b 3 mA b 1 mA b 3 mA VOL Output LOW Voltage 54F 10% VCC 74F 10% VCC 0.5 0.5 V Min IIH Input HIGH Current 54F 74F 20.0 5.0 mA Max VIN e 2.7V IBVI Input HIGH Current Breakdown Test 54F 74F 100 7.0 mA Max VIN e 7.0V ICEX Output HIGH Leakage Current 54F 74F 250 50 mA Max VOUT e VCC VID Input Leakage Test 74F V 0.0 IID e 1.9 mA All Other Pins Grounded IOD Output Leakage Circuit Current 74F 3.75 mA 0.0 VIOD e 150 mV All Other Pins Grounded IIL Input LOW Current b 0.6 mA Max VIN e 0.5V IOZH Output Leakage Current 50 mA Max VOUT e 2.7V IOZL Output Leakage Current b 50 mA Max VOUT e 0.5V IOS Output Short-Circuit Current b 150 mA Max VOUT e 0V IZZ Bus Drainage Test 500 mA 0.0V VOUT e 5.25V ICCL Power Supply Current 35 55 mA Max VO e LOW ICCZ Power Supply Current 35 55 mA Max VO e HIGH Z 4.75 b 60 3 AC Electrical Characteristics Symbol Parameter 74F 54F 74F TA e a 25 C VCC e a 5.0V CL e 50 pF TA, VCC e Mil CL e 50 pF TA, VCC e Com CL e 50 pF Units Min Typ Max Min Max Min Max tPLH tPHL Propagation Delay Dn to On 3.0 2.0 5.3 3.7 7.0 6.0 3.0 2.0 9.0 7.0 3.0 2.0 8.0 6.5 ns tPLH tPHL Propagation Delay LE to On 5.0 3.0 9.0 5.2 11.0 7.0 5.0 3.0 13.5 7.5 5.0 3.0 12.0 7.0 ns tPZH tPZL Output Enable Time 2.0 2.0 5.0 5.6 8.0 8.5 2.0 2.0 10.0 10.0 2.0 2.0 9.0 9.5 tPHZ tPLZ Output Disable Time 1.5 1.5 4.5 3.8 5.5 5.5 1.5 1.5 7.0 5.5 1.5 1.5 6.5 5.5 ns AC Operating Requirements Symbol Parameter 74F 54F 74F TA e a 25 C VCC e a 5.0V TA, VCC e Mil TA, VCC e Com Min Min Min Max Max ts(H) ts(L) Setup Time, HIGH or LOW Dn to LE 2.0 2.0 2.0 2.0 2.0 2.0 th(H) th(L) Hold Time, HIGH or LOW Dn to LE 3.0 3.5 3.0 4.0 3.0 3.5 tw(H) LE Pulse Width, HIGH 4.0 4.0 4.0 4 Units Max ns ns Ordering Information The device number is used to form part of a simplified purchasing code where the package type and temperature range are defined as follows: 74F 573 S Temperature Range Family 74F e Commercial 54F e Military C X Special Variations QB e Military grade device with environmental and burn-in processing X e Devices shipped in 13x reels Device Type Package Code P e Plastic DIP D e Ceramic DIP F e Flatpak L e Leadless Chip Carrier (LCC) S e Small Outline SOIC JEDEC SJ e Small Outline SOIC EIAJ Temperature Range C e Commercial (0 C to a 70 C) M e Military (b55 C to a 125 C) Physical Dimensions inches (millimeters) 20-Lead Ceramic Leadless Chip Carrier (L) NS Package Number E20A 5 Physical Dimensions inches (millimeters) (Continued) 20-Lead Ceramic Dual-In-Line Package (D) NS Package Number J20A 20-Lead (0.300x Wide) Molded Small Outline Package, JEDEC (S) NS Package Number M20B 6 Physical Dimensions inches (millimeters) (Continued) 20-Lead (0.300x Wide) Small Outline Package, EIAJ (SJ) NS Package Number M20D 20-Lead (0.300x Wide) Molded Dual-In-Line Package (P) NS Package Number N20A 7 54F/74F573 Octal D-Type Latch with TRI-STATE Outputs Physical Dimensions inches (millimeters) (Continued) 20 Lead Ceramic Flatpak (F) NS Package Number W20A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.