INCH-POUND MIL-DTL-83723/74F 19 August 2009 SUPERSEDING MIL-DTL-83723/74E 20 October 2000 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SINGLE HOLE MOUNT, BAYONET COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES A, G, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use. MIL-DTL-83723/74F FIGURE 1. Dimensions and configurations - Continued. 2 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use. MIL-DTL-83723/74F Shell size 8 B C D max F max .312 .561 .388 .696 .558 .875 .627 .935 .772 1.062 .860 1.187 .985 1.312 1.110 1.437 1.235 1.562 G N thread .137 .097 .137 .097 .137 .097 .137 .097 .137 .097 .137 .097 .137 .097 .168 .128 .168 .128 .428 .433 .530 .535 .700 .705 .769 .774 .869 .901 1.002 1.007 1.127 1.132 1.252 1.257 1.377 1.382 Shell size U V max S +.005 -.000 W max 8 .670 .979 .508 1.068 .605 .635 10 .796 1.104 .636 1.192 .730 .760 12 .984 1.291 .806 1.380 .917 .947 14 1.046 1.391 .875 1.505 .980 1.010 16 1.171 1.516 1.002 1.630 1.105 1.135 18 1.296 1.641 1.108 1.756 1.229 1.260 20 1.484 1.766 1.233 1.860 1.354 1.385 22 1.609 1.954 1.358 2.086 1.479 1.510 24 1.734 2.079 1.483 2.160 1.604 1.635 10 12 14 16 18 20 22 24 .536 .531 .659 .654 .829 .824 .898 .893 1.025 1.020 1.131 1.126 1.256 1.251 1.381 1.376 1.506 1.501 EE .625-20 UN-2A .750-20 UNEF-2A .9375-20 UNEF-2A 1.000-20 UNEF-2A 1.125-20 UNEF-2A 1.250-18 UNEF-2A 1.375-18 UNEF-2A 1.500-18 UNEF-2A 1.625-18 UNEF-2A FF FIGURE 1. Dimensions and configurations - Continued. 3 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use. JJ .596 .590 .721 .715 .908 .902 .971 .965 1.096 1.090 1.220 1.214 1.345 1.339 1.470 1.464 1.595 1.589 MIL-DTL-83723/74F Inches mm Inches mm Inches mm Inches mm Inches mm .005 .008 .015 .018 .019 .020 .022 .032 .042 .046 .062 .065 .069 .071 .076 .084 .089 .090 .093 .094 .097 .098 .101 .106 .109 .112 .125 .128 .137 .138 .144 .168 .198 .204 0.13 0.20 0.38 0.46 0.48 0.51 0.56 0.81 1.07 1.17 1.57 1.65 1.75 1.80 1.93 2.13 2.26 2.29 2.36 2.39 2.46 2.49 2.57 2.69 2.77 2.84 3.18 3.25 3.48 3.51 3.66 4.27 5.03 5.18 .211 .259 .312 .366 .376 .378 .380 .388 .392 .428 .433 .461 .481 .490 .508 .530 .535 .539 .540 .558 .560 .561 .590 .596 .605 .625 .627 .635 .636 .670 .696 .700 .705 .715 5.36 6.58 7.92 9.30 9.55 9.60 9.65 9.86 9.96 10.87 11.00 11.71 12.22 12.45 12.90 13.46 13.59 13.69 13.72 14.17 14.22 14.25 14.99 15.14 15.37 15.88 15.93 16.13 16.15 17.02 17.68 17.78 17.91 18.16 .721 .730 .750 .760 .761 .769 .772 .774 .781 .796 .806 .860 .875 .896 .901 .902 .908 .917 .935 .9375 .947 .965 .971 .979 .980 .984 .985 1.000 1.002 1.007 1.010 1.046 1.062 1.068 18.31 18.54 19.05 19.30 19.33 19.53 19.61 19.66 19.84 20.22 20.47 21.84 22.23 22.76 22.89 22.91 23.06 23.29 23.75 23.81 24.05 24.51 24.66 24.87 24.89 24.99 25.02 25.40 25.45 25.58 25.65 26.57 26.97 27.13 1.090 1.096 1.104 1.105 1.108 1.110 1.125 1.127 1.132 1.135 1.171 1.187 1.192 1.214 1.220 1.229 1.233 1.235 1.250 1.252 1.257 1.260 1.291 1.296 1.300 1.312 1.339 1.345 1.354 1.358 1.375 1.377 1.380 1.382 27.69 27.84 28.04 28.07 28.14 28.19 28.58 28.63 28.75 28.83 29.74 30.15 30.28 30.84 30.99 31.22 31.32 31.37 31.75 31.80 31.93 32.00 32.79 32.92 33.02 33.32 34.01 34.16 34.39 34.49 34.93 34.98 35.05 35.10 1.385 1.391 1.437 1.455 1.464 1.470 1.479 1.483 1.484 1.500 1.510 1.516 1.562 1.589 1.595 1.604 1.609 1.625 1.630 1.635 1.641 1.734 1.756 1.766 1.860 1.954 2.068 2.079 2.160 35.18 35.33 36.50 36.96 37.19 37.34 37.57 37.67 37.69 38.10 38.35 38.51 39.67 40.36 40.51 40.74 41.87 41.28 41.40 41.53 41.68 44.04 44.60 44.86 47.24 49.63 52.53 52.81 54.86 FIGURE 1. Dimensions and configurations - Continued. 4 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use. MIL-DTL-83723/74F NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals, and 1 for all angles. 4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 5. The centerline of indicated projection shall be located on vertical centerline 2. 6. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities. Shell size 8 10 Insert arrangements 03 06 Contact cavities 1, 2, 3 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049. This connector mates with MIL-DTL-83723/75 and /77. O-ring shall be furnished with connector. Part or Identifying Number (PIN) example: M83723/ 74 R 22 Military designator Specification sheet number Class Shell size Insert arrangement Polarizing position 5 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use. 55 N MIL-DTL-83723/74F Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 MS3186 SAE-AS85049 CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA-CC (Project 5935-2008-127) Review activities: Army - AR, AV, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 6 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z Check the source to verify that this is the current version before use.