DETAIL SPECIFIC ATION SHEET
CONNECTORS, ELECTRIC, (CIRCULAR, ENVIRONMENT RESISTING),
RECEPTACLE, (SINGLE HOLE MOUNT, BAYONET COUPLING, CRIMP PIN CONTACT) ,
(SERIES III, CLASSES A, G, M, R, T, W AND Z)
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Dimensions and configurations.
AMSC N/A FSC 5935
INCH-POUND
MIL-DTL-83723/74F
19 August 2009
SUPERSEDING
MIL-DTL-83723/74E
20 October 2000
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
MIL-DTL-83723/74F
2
FIGURE 1. Dimensions and configurations - Continued.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
MIL-DTL-83723/74F
3
Shell
size
B
C
D
max
F
max
G
N thread
8
.137
.097
.428
.433
.312 .561 .536
.531
.625-20 UN-2A
10
.137
.097
.530
.535
.388 .696 .659
.654
.750-20 UNEF-2A
12
.137
.097
.700
.705
.558 .875
.829
.824
.9375-20 UNEF-2A
14
.137
.097
.769
.774
.627 .935
.898
.893
1.000-20 UNEF-2A
16
.137
.097
.869
.901
.772 1.062
1.025
1.020
1.125-20 UNEF-2A
18
.137
.097
1.002
1.007
.860 1.187
1.131
1.126
1.250-18 UNEF-2A
20
.137
.097
1.127
1.132
.985 1.312
1.256
1.251
1.375-18 UNEF-2A
22
.168
.128
1.252
1.257
1.110 1.437 1.381
1.376
1.500-18 UNEF-2A
24
.168
.128
1.377
1.382
1.235 1.562
1.506
1.501
1.625-18 UNEF-2A
Shell
size U V
max S
+.005
-.000
W
max EE FF JJ
8 .670 .979 .508 1.068 .605 .635
.596
.590
10 .796 1.104 .636 1.192 .730 .760
.721
.715
12 .984 1.291 .806 1.380 .917 .947
.908
.902
14 1.046 1.391 .875 1.505 .980 1.010 .971
.965
16 1.171 1.516 1.002 1.630 1.105 1.135 1.096
1.090
18 1.296 1.641 1.108 1.756 1.229 1.260
1.220
1.214
20 1.484 1.766 1.233 1.860 1.354 1.385
1.345
1.339
22 1.609 1.954 1.358 2.086 1.479 1.510
1.470
1.464
24 1.734 2.079 1.483 2.160 1.604 1.635
1.595
1.589
FIGURE 1. Dimensions and configurations - Continued.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
MIL-DTL-83723/74F
4
Inches mm Inches mm Inches mm Inches mm Inches mm
.005
0.13
.211
5.36
.721
18.31
1.090
27.69
1.385
35.18
.008
0.20
.259
6.58
.730
18.54
1.096
27.84
1.391
35.33
.015
0.38
.312
7.92
.750
19.05
1.104
28.04
1.437
36.50
.018
0.46
.366
9.30
.760
19.30
1.105
28.07
1.455
36.96
.019
0.48
.376
9.55
.761
19.33
1.108
28.14
1.464
37.19
.020
0.51
.378
9.60
.769
19.53
1.110
28.19
1.470
37.34
.022
0.56
.380
9.65
.772
19.61
1.125
28.58
1.479
37.57
.032
0.81
.388
9.86
.774
19.66
1.127
28.63
1.483
37.67
.042
1.07
.392
9.96
.781
19.84
1.132
28.75
1.484
37.69
.046
1.17
.428
10.87
.796
20.22
1.135
28.83
1.500
38.10
.062
1.57
.433
11.00
.806
20.47
1.171
29.74
1.510
38.35
.065
1.65
.461
11.71
.860
21.84
1.187
30.15
1.516
38.51
.069
1.75
.481
12.22
.875
22.23
1.192
30.28
1.562
39.67
.071
1.80
.490
12.45
.896
22.76
1.214
30.84
1.589
40.36
.076
1.93
.508
12.90
.901
22.89
1.220
30.99
1.595
40.51
.084
2.13
.530
13.46
.902
22.91
1.229
31.22
1.604
40.74
.089
2.26
.535
13.59
.908
23.06
1.233
31.32
1.609
41.87
.090
2.29
.539
13.69
.917
23.29
1.235
31.37
1.625
41.28
.093
2.36
.540
13.72
.935
23.75
1.250
31.75
1.630
41.40
.094
2.39
.558
14.17
.9375
23.81
1.252
31.80
1.635
41.53
.097
2.46
.560
14.22
.947
24.05
1.257
31.93
1.641
41.68
.098
2.49
.561
14.25
.965
24.51
1.260
32.00
1.734
44.04
.101
2.57
.590
14.99
.971
24.66
1.291
32.79
1.756
44.60
.106
2.69
.596
15.14
.979
24.87
1.296
32.92
1.766
44.86
.109
2.77
.605
15.37
.980
24.89
1.300
33.02
1.860
47.24
.112
2.84
.625
15.88
.984
24.99
1.312
33.32
1.954
49.63
.125
3.18
.627
15.93
.985
25.02
1.339
34.01
2.068
52.53
.128
3.25
.635
16.13
1.000
25.40
1.345
34.16
2.079
52.81
.137
3.48
.636
16.15
1.002
25.45
1.354
34.39
2.160
54.86
.138
3.51
.670
17.02
1.007
25.58
1.358
34.49
.144
3.66
.696
17.68
1.010
25.65
1.375
34.93
.168
4.27
.700
17.78
1.046
26.57
1.377
34.98
.198
5.03
.705
17.91
1.062
26.97
1.380
35.05
.204
5.18
.715
18.16
1.068
27.13
1.382
35.10
FIGURE 1. Dimensions and configurations - Continued.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
MIL-DTL-83723/74F
5
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals, and ± 1° for all angles.
4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
5. The centerline of indicated projection shall be located on vertical centerline ± 2°.
6. See table I for contact cavities requiring this dimension.
FIGURE 1. Dimensions and configurations - Continued.
REQUIREMENTS:
Dimensions and configuration: See figure 1.
For insert arrangements, see MIL-STD-1554 and table I.
TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities.
Shell
size
Insert
arrangements
Contact
cavities
8
10 03
06 1, 2, 3
1, 2, 3, 4, 5, 6
For connector accessories: See SAE-AS85049.
This connector mates with MIL-DTL-83723/75 and /77.
O-ring shall be furnished with connector.
Part or Identifying Number (PIN) example:
M83723/ 74 R 22 55 N
Military designator
Specification sheet number
Class
Shell size
Insert arrangement
Polarizing position
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
MIL-DTL-83723/74F
6
Changes from previous issue. Marginal notations are not used in this revision to identify changes with
respect to the previous issue due to the extent of the changes.
Referenced documents. In addition to MIL-DTL-83723, this document references the following:
MIL-DTL-83723/75
MIL-DTL-83723/77
MIL-STD-1554
MS3186
SAE-AS85049
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA-CC
Navy - AS
Air Force - 85 (Project 5935-2008-127)
DLA - CC
Review activities:
Army - AR, AV, MI
Navy - EC
Air Force - 19, 99
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above
using the ASSIST Online database at http://assist.daps.dla.mil.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:02Z
Check the source to verify that this is the current version before use.
