SAP-839125013D0G - Seiko Instruments USA, Inc.

DOCUMENT NUMBER NCD-4oB8-07

SAP-8 Series

Single-Mode

FC CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Seiko Instruments Inc.

OFC Division.

8, Nakase 1-Chome

Mihama-ku, Chiba-shi, Chiba-ken

261-8507 JAPAN

Telephone : +81-43-211-1211

Facsimile : +81-43-211-8039

SAP-8 Series Single-Mode FC CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Document Number NCD-4oB8-07

NCD-4oB8-01 October 1994

NCD-4oB8-02 January 1995

NCD-4oB8-03 January 1996

NCD-4oB8-04 June 1997

NCD-4oB8-05 May 1998

NCD-4oB8-06 April 2000

NCD-4oB8-07 May 2003

The information contained herein shall not reproduced or disclosed to any third party

without the express written consent of SII.

The Specifications contained herein are subject to change without notice.

SII is a trademark of Seiko Instruments Inc.

Please address any questions, comments, and suggestions to:

Seiko Instruments USA Inc.

Electronics Components Division

2990 West Lomita Boulevard

Torrance, CA 90505, U.S.A.

Phone: +1-310-517-7780

Facsimile: +1-310-517-7792

Seiko Instruments GmbH

OFC Division

Siemensstraße 9b

D-63263 Neu-Isenburg, Germany

Phone: +49-6102-297-0

Facsimile: +49-6102-297-211

Seiko Instruments (H.K.) Ltd.

Sales Department

4th & 5th Floor, Wyler Center 2

200 Tai Lin Pai Road, Kwai Chung

N.T., Kowloon, Hong Kong

Phone: +852-2421-8611

Facsimile: +852-2480-5479

Seiko Instruments Taiwan Inc.

Sales Department

4F, No.40, Sec. 2, Min Chuan E. Rd.,

Taipei 104, Taiwan, R.O.C.

Phone: +886-2-2563-5001

Facsimile: +886-2-2521-9519

Seiko Instruments Singapore pte. Ltd.

Component Sales Department

2, Marsiling Lane,

Singapore, 739144, Singapore

Phone: +65-269-1370

Facsimile: +65-269-9729

iii

TABLE OF CONTENTS

Section Page

1. PROVISION 1

1.1. Application limit 1

2. PARTS NUMBER 1

3. GENERAL SPECIFICATIONS 2

3.1. Parts and Materials 2

3.2. Physical Dimensions 2

3.3. General Tolerances 3

4. PACKING 3

5. NOTE 3

Table

Table 1 Parts number 1

Table 2 Parts and materials 2

Table 3 Parts and materials (Mainbody) 2

Table 4 General tolerance 2

Figure

Figure 1 to 2 SAP-8 Connector 4 to 5

Figure 3 to 4 Mainbody 6

Figure 5 to 13 Part dimensions 7 to 9

1. PROVISION

1.1 Application Limit

These specifications apply to the SAP-8 Single-Mode FC CONNECTOR PLUG supplied

by SII.

2. PARTS NUMBER

Parts number of the connector is shown in Table 1.

Table 1 Parts number

MODEL Number TYPE Number

SAP-8 331251A3D0

Hood color

0 without hood ( Requied )

1 Black 3 0 0 machining frame type

3 White key-ring un-installed

5 Blue Bulk pa cking

3 D 0 Molding frame type

Hood Inner Dia Bulk packing

0 without hood 7 0 0 machining frame type

1 0.9mm (non flamable) key-ring pre-installed

3 3.0mm (Plastic) Bulk pa ckin g

6 2.0mm (Plastic)

9 0.9mm (Plastic)

Fe rrule I nner Dia

S5 to S6 Cap

( 0.125 to 0.126mm ) 1 Black PVC

Black Fe rrule Cap

Marking of Hood

pplicable Hood (mm)

0 without 0.9mm (non flamable)

1SII Marking 0.9 to 3.0mm (Plastic)

3. GENERAL SPECIFICATIONS

3.1 Parts and Materials

Parts and the materials are shown in Table 2 to 3.

Table 2. Parts and materials

No. Part Name Q'ty Material Notes

1-1 See Table 3 Machining frame type,

(#6,7,8-1,9,10,11,12-1, Sub-assembled)

1-2

Mainbody 1

See Table 3 Molding frame type,

(#6,7,8-2,10,11,12-2, Sub-assembled)

2Key-ring (1) Beryllium copper for machining frame type

3-1 Aluminum alloy for φ3.0mm cable

3-2 Crimping ring (1) Aluminum alloy for φ2.0mm cable

4-1 Thermal plastic elastomer φ3.0mm, UL94V-0

4-2 Thermal plastic elastomer φ2.0mm, UL94V-0

4-3 Thermal plastic elastomer φ0.9mm, UL94V-0

4-4

Hood (1)

Synthetic rubber φ0.9mm, UL94V-0

5-1 PP Black

5-2 Cap 1PVC Black

Table 3. Parts and materials ( Mainbody )

No. Part Name Q'ty Material Notes

6 Ferrule 1 Zirconia − −

7 Flange 1 Brass Nickel plating

8-1 Stainless Steel Machining type

8-2 Frame 1 Zinc Die-casting Molding type , Nickel Plating

9 Washer (1) Phosphor bronze for machining frame type , Nickel Plating

10 Spring 1 Stainless steel − −

11 Coupling nut 1 Brass Nickel plating

12-1 Brass for machining frame type , Nickel Plating

12-2 Stopper 1 Brass for molding frame type , Nickel Plating

3.2 Physical Dimensions

Figure 1 to 2 shows the assembled state of SAP-8.

Figure 3 to 4 shows the Mainbody.

Figure 5 to 13 show the part dimension.

- In accordance with IEC 61754-13 Fibre optic connector interface -

Part 13 : Type FC-PC connector family.

3.3 General Tolerance

Permissible deviation in dimensions without tolerance indication is in accordance with JIS

B 0405 class m, as shown in Table 4.

Table 4 General tolerance (JIS B 0405 class m)

Basic size step [mm]

Over Under Permissible deviation [mm]

0.5 3 ±0.1

36 ±0.1

630 ±0.2

30 120 ±0.3

4. PACKING

The product is packed to prevent damage during shipment.

5. NOTE

When discarding this product, please follow the regulation of your own country.

note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not

assembled like this.

note.2: This drawing does not include caps. Unit: mm

Figure 1 SAP-8 Connector ( Machining frame type )

note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not

assembled like this.

note.2: This drawing does not include caps. Unit: mm

Figure 2 SAP-8 Connector ( Molding frame type )

note.1: End curve offset = 0.05mm or less. Unit: mm

Figure 3 #1-1. Mainbody ( Machining frame ytpe )

note.1: End curve offset = 0.05mm or less. Unit: mm

Figure 4 #1-2. Mainbody ( Molding frame ytpe )

Unit: mm

Figure 5 #2 Keyring ( for machining frame type )

Unit: mm

Figure 6 #3-1. Crimping ring ( for 3.0mm cord )

Unit: mm

Figure 7 #3-2. Crimping ring ( for 2.0mm cord )

Unit: mm

Figure 8 #4-1. Hood ( for 3.0mm cord )

Unit: mm

Figure 9 #4-2. Hood ( for 2.0mm cord )

Unit: mm

Figure 10 #4-3. Hood ( for 0.9mm buffered fiber )

Unit: mm

Figure 11 #4-4. Hood ( for 0.9mm buffered fiber )

Unit: mm

Figure 12 #5-1. Cap ( Ferrule Cap )

Unit: mm

Figure 13 #5-2. Cap ( PVC )