LTC2157-12/ LTC2156-12/LTC2155-12 Dual 12-Bit 250Msps/ 210Msps/170Msps ADCs FEATURES n n n n n n n n n n n n DESCRIPTION 68.5dB SNR 90dB SFDR Low Power: 628mW/592mW/545mW Total Single 1.8V Supply DDR LVDS Outputs Easy-to-Drive 1.5VP-P Input Range 1.25GHz Full-Power Bandwidth S/H Optional Clock Duty Cycle Stabilizer Low Power Sleep and Nap Modes Serial SPI Port for Configuration Pin Compatible 14-Bit Versions 64-Lead (9mm x 9mm) QFN Package The LTC(R)2157-12/LTC2156-12/LTC2155-12 are a family of dual 250Msps/210Msps/170Msps 12-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. They are perfect for demanding communications applications with AC performance that includes 68.5dB SNR and 90dB spurious free dynamic range (SFDR). The 1.25GHz input bandwidth allows the ADC to achieve high undersampling ratio with very low attenuation. The latency is only six clock cycles. DC specs include 0.26LSB INL (typ), 0.16LSB DNL (typ) and no missing codes over temperature. The transition noise is 0.54LSBRMS. The digital outputs are double data rate (DDR) LVDS. APPLICATIONS n n n n n n The ENC+ and ENC- inputs can be driven differentially with a sine wave, PECL, LVDS, TTL, or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles. Communications Cellular Basestations Software Defined Radios Medical Imaging High Definition Video Testing and Measurement Instruments L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION VDD CLOCK ANALOG INPUT S/H CLOCK/DUTY CYCLE CONTROL S/H 12-BIT PIPELINED ADC CORE CORRECTION LOGIC OUTPUT DRIVERS DA10_11 * * * DA0_1 OGND OVDD CHANNEL B 12-BIT PIPELINED ADC CORE CORRECTION LOGIC OUTPUT DRIVERS DB10_11 * * * DB0_1 -20 -40 -60 -80 -100 DDR LVDS GND 21576512 TA01 0 DDR LVDS AMPLITUDE (dBFS) ANALOG INPUT LTC2157-12: 32K Points 2-Tone FFT, fIN = 71MHZ and 69MHz, 250Msps OVDD CHANNEL A OGND -120 0 20 40 60 80 100 FREQUENCY (MHz) 120 21576512 G11 21576512fb For more information www.linear.com/LTC2157-12 1 LTC2157-12/ LTC2156-12/LTC2155-12 TOP VIEW VDD 1 VDD 2 GND 3 AINA+ 4 AINA- 5 GND 6 SENSE 7 VREF 8 GND 9 VCM 10 GND 11 AINB- 12 AINB+ 13 GND 14 VDD 15 VDD 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 65 GND OGND DA2_3+ DA2_3- DA0_1+ DA0_1- NC NC CLKOUT+ CLKOUT- DB10_11+ DB10_11- DB8_9+ DB8_9- DB6_7+ DB6_7- OGND VDD GND ENC+ ENC- GND OF - OF + NC NC DB0_1- DB0_1+ DB2_3- DB2_3+ DB4_5 - DB4_5+ OVDD 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Supply Voltage VDD, OVDD................................................. -0.3V to 2V Analog Input Voltage AINA/B+, AINA/B -, PAR/SER, SENSE (Note 3)......................... -0.3V to (VDD + 0.2V) Digital Input Voltage ENC+, ENC- (Note 3)................. -0.3V to (VDD + 0.3V) CS, SDI, SCK (Note 4)............................ -0.3V to 3.9V SDO (Note 4).............................................. -0.3V to 3.9V Digital Output Voltage................. -0.3V to (OVDD + 0.3V) Operating Temperature Range LTC2157C, LTC2156C, LTC2155C............. 0C to 70C LTC2157I, LTC2156I, LTC2155I.............-40C to 85C Storage Temperature Range................... -65C to 150C PIN CONFIGURATION VDD PAR/SER CS SCK SDI SDO GND DA10_11+ DA10_11- DA8_9+ DA8_9- DA6_7+ DA6_7- DA4_5+ DA4_5 - OVDD (Notes 1, 2) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 ABSOLUTE MAXIMUM RATINGS UP PACKAGE 64-LEAD (9mm x 9mm) PLASTIC QFN TJMAX = 150C, JA = 20C/W EXPOSED PAD (PIN 65) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2157CUP-12#PBF LTC2157CUP-12#TRPBF LTC2157UP-12 64-Lead (9mm x 9mm) Plastic QFN 0C to 70C LTC2157IUP-12#PBF LTC2157IUP-12#TRPBF LTC2157UP-12 64-Lead (9mm x 9mm) Plastic QFN -40C to 85C LTC2156CUP-12#PBF LTC2156CUP-12#TRPBF LTC2156UP-12 64-Lead (9mm x 9mm) Plastic QFN 0C to 70C LTC2156IUP-12#PBF LTC2156IUP-12#TRPBF LTC2156UP-12 64-Lead (9mm x 9mm) Plastic QFN -40C to 85C LTC2155CUP-12#PBF LTC2155CUP-12#TRPBF LTC2155UP-12 64-Lead (9mm x 9mm) Plastic QFN 0C to 70C LTC2155IUP-12#PBF LTC2155IUP-12#TRPBF LTC2155UP-12 64-Lead (9mm x 9mm) Plastic QFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 21576512fb 2 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) PARAMETER CONDITIONS MIN Resolution (No Missing Codes) l LTC2157-12 TYP MAX MIN 12 LTC2156-12 TYP MAX LTC2155-12 MIN TYP MAX 12 UNITS 12 Bits Integral Linearity Error Differential Analog Input (Note 6) l -2.3 0.26 2.3 -2.2 0.30 2.2 -1.9 0.30 1.9 LSB Differential Linearity Error Differential Analog Input l -0.6 0.16 0.8 -0.6 0.16 0.6 -0.6 0.16 0.6 LSB Offset Error (Note 7) l -13 5 13 -13 5 13 -13 5 13 mV Gain Error External Reference l -4 1 2.2 -4 1 2.2 -4 1 2.2 %FS Offset Drift Full-Scale Drift Internal Reference External Reference Transition Noise 20 20 20 V/C 30 10 30 10 30 10 ppm/C ppm/C 0.54 0.54 0.54 LSBRMS ANALOG INPUT The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VIN Analog Input Range (AIN+ - AIN-) 1.7V < VDD < 1.9V l VIN(CM) Analog Input Common Mode (AIN+ + AIN-)/2 Differential Analog Input (Note 8) l VCM - 20mV VCM VCM + 20mV V VSENSE External Voltage Reference Applied to SENSE External Reference Mode l 1.200 1.250 1.300 V 1.5 VP-P IIN1 Analog Input Leakage Current 0 < AIN+, AIN- < VDD, No Encode l -1 1 A IIN2 PAR/SER Input Leakage Current 0 < PAR/SER < VDD l -1 1 A IIN3 SENSE Input Leakage Current 1.2V < SENSE < 1.3V l -1 1 A tAP Sample-and-Hold Acquisition Delay Time 1 tJITTER Sample-and-Hold Acquisition Delay Jitter 0.15 ns CMRR Analog Input Common Mode Rejection Ratio BW-3B Full-Power Bandwidth psRMS 75 dB 1250 MHz DYNAMIC ACCURACY The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. AIN = -1dBFS. (Note 5) SYMBOL PARAMETER CONDITIONS SNR Signal-to-Noise Ratio 15MHz Input 70MHz Input 140MHz Input SFDR Spurious Free Dynamic Range 15MHz Input 2nd or 3rd Harmonic 70MHz Input 140MHz Input Spurious Free Dynamic Range 15MHz Input 4th Harmonic or Higher 70MHz Input 140MHz Input S/(N+D) Crosstalk Signal-to-Noise Plus Distortion Ratio Crosstalk Between Channels 15MHz Input 70MHz Input 140MHz Input Up to 315MHz Input MIN l l l l LTC2157-12 TYP MAX 66.9 68.5 68.4 68.0 71 90.6 88 80 81 98 95 85 66.1 68.4 68.3 67.7 MIN LTC2156-12 TYP MAX 67.3 68.5 68.3 67.9 74 90.1 89 81 82 98 95 87 66.7 68.4 68.3 67.7 -95 -95 LTC2155-12 MIN TYP MAX UNITS 67.4 68.5 68.3 67.8 dBFS dBFS dBFS 75 90 88 80 dBFS dBFS dBFS 83 98 95 88 dBFS dBFS dBFS 66.8 68.4 68.3 67.7 dBFS dBFS dBFS -95 dB 21576512fb For more information www.linear.com/LTC2157-12 3 LTC2157-12/ LTC2156-12/LTC2155-12 INTERNAL REFERENCE CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) PARAMETER CONDITIONS VCM Output Voltage IOUT = 0 MIN TYP MAX 0.435 * VDD - 18mV 0.435 * VDD 0.435 * VDD + 18mV VCM Output Temperature Drift UNITS 37 VCM Output Resistance -1mA < IOUT < 1mA VREF Output Voltage IOUT = 0 ppm/C 4 1.225 1.250 VREF Output Temperature Drift 1.275 V 30 VREF Output Resistance -400A < IOUT < 1mA VREF Line Regulation 1.7V < VDD < 1.9V V ppm/C 7 0.6 mV/V POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER CONDITIONS MIN LTC2157-12 TYP MAX MIN LTC2156-12 TYP MAX LTC2155-12 MIN TYP MAX UNITS VDD Analog Supply Voltage (Note 9) l 1.7 1.8 1.9 1.7 1.8 1.9 1.7 1.8 1.9 V OVDD Output Supply Voltage (Note 9) l 1.7 1.8 1.9 1.7 1.8 1.9 1.7 1.8 1.9 V IVDD Analog Supply Current l 309 345 291 320 266 295 mA IOVDD Digital Supply Current 1.75mA LVDS Mode 3.5mA LVDS Mode l l 40 68 46 76 38 66 45 75 37 65 42 74 mA mA PDISS Power Dissipation 1.75mA LVDS Mode 3.5mA LVDS Mode l l 628 679 704 758 592 643 657 711 545 596 607 665 mW mW PSLEEP Sleep Mode Power Clock Disabled Clocked at fS(MAX) <5 <5 <5 <5 <5 <5 mW mW PNAP Nap Mode Power Clocked at fS(MAX) 181 168 154 mW DIGITAL INPUTS AND OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS ENCODE INPUTS (ENC+, ENC-) VID Differential Input Voltage (Note 8) l 0.2 VICM Common Mode Input Voltage Internally Set Externally Set (Note 8) l 1.1 V 1.2 1.5 V V RIN Input Resistance (See Figure 2) 10 k CIN Input Capacitance (Note 8) 2 pF DIGITAL INPUTS (CS, SDI, SCK) VIH High Level Input Voltage VDD = 1.8V l VIL Low Level Input Voltage VDD = 1.8V l IIN Input Current VIN = 0V to 3.6V l CIN Input Capacitance (Note 8) 1.3 V -10 0.6 V 10 A 3 pF 200 SDO OUTPUT (Open-Drain Output. Requires 2k Pull-Up Resistor if SDO Is Used) ROL Logic Low Output Resistance to GND VDD = 1.8V, SDO = 0V IOH Logic High Output Leakage Current SDO = 0V to 3.6V COUT Output Capacitance (Note 8) l -10 10 4 A pF 21576512fb 4 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 DIGITAL INPUTS AND OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL PARAMETER DIGITAL DATA OUTPUTS CONDITIONS VOD Differential Output Voltage VOS Common Mode Output Voltage RTERM On-Chip Termination Resistance 100 Differential Load, 3.5mA Mode 100 Differential Load, 1.75mA Mode 100 Differential Load, 3.5mA Mode 100 Differential Load, 1.75mA Mode Termination Enabled, OVDD = 1.8V l l l l MIN TYP MAX UNITS 247 125 1.125 1.125 350 175 1.250 1.250 100 454 250 1.375 1.375 mV mV V V TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 5) SYMBOL fS tL PARAMETER Sampling Frequency ENC Low Time (Note 8) tH ENC High Time (Note 8) CONDITIONS (Note 9) Duty Cycle Stabilizer Off Duty Cycle Stabilizer On Duty Cycle Stabilizer Off Duty Cycle Stabilizer On l l l l l MIN 10 1.9 1.5 1.9 1.5 LTC2157-12 TYP MAX 250 2 50 2 50 2 50 2 50 MIN 10 2.26 1.5 2.26 1.5 LTC2156-12 TYP MAX 210 2.38 50 2.38 50 2.38 50 2.38 50 LTC2155-12 MIN TYP MAX 10 170 2.79 2.94 50 1.5 2.94 50 2.79 2.94 50 1.5 2.94 50 UNITS MHz ns ns ns ns DIGITAL DATA OUTPUTS LTC215X-12 MIN SYMBOL tD PARAMETER ENC to Data Delay CONDITIONS CL = 5pF (Note 8) l tC ENC to CLKOUT Delay CL = 5pF (Note 8) l tSKEW DATA to CLKOUT Skew tD - tC (Note 8) l Pipeline Latency TYP MAX 1.7 2 2.3 ns 1.3 1.6 2 ns 0.3 0.4 0.55 ns 6 6 UNITS Cycles SPI Port Timing (Note 8) tSCK SCK Period tS CS to SCK Set-Up Time tH Write Mode Readback Mode CSDO = 20pF, RPULLUP = 2k l 40 250 5 ns ns ns SCK to CS Hold Time l 5 ns tDS SDI Set-Up Time l 5 ns tDH SDI Hold Time l 5 tDO SCK Falling to SDO Valid Readback Mode, CSDO = 20pF, RPULLUP = 2k Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to GND with GND and OGND shorted (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: When these pin voltages are taken below GND they will be clamped by internal diodes. When these pin voltages are taken above VDD they will not be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND without latchup. l l l ns 125 ns Note 5: VDD = OVDD = 1.8V, fSAMPLE = 250MHz (LTC2157), 210MHz (LTC2156), or 170MHz (LTC2155), differential ENC+/ENC- = 2VP-P sine wave, input range = 1.5VP-P with differential drive, unless otherwise noted. Note 6: Integral nonlinearity is defined as the deviation of a code from a best fit straight line to the transfer curve. The deviation is measured from the center of the quantization band. Note 7: Offset error is the offset voltage measured from -0.5LSB when the output code flickers between 0000 0000 0000 and 1111 1111 1111 in 2's complement output mode. Note 8: Guaranteed by design, not subject to test. Note 9: Recommended operating conditions. 21576512fb For more information www.linear.com/LTC2157-12 5 LTC2157-12/ LTC2156-12/LTC2155-12 TIMING DIAGRAMS Double-Data Rate Output Timing, All Outputs Are Differential LVDS N tAP N+3 N+2 N+1 tL tH ENC- ENC+ CLKOUT+ CLKOUT - DA0_1- DA0_1+ DA10_11- DA10_11+ DB0_1- DB0_1+ tC DA0N-6 DA1N-6 DA0N-5 DA1N-5 DA0N-4 DA1N-4 tD DA10N-6 DA11N-6 DA10N-5 DA11N-5 DA10N-4 DA11N-4 DB0N-6 DB1N-6 DB0N-5 DB1N-5 DB0N-4 DB1N-4 DB10_11- DB10_11+ DB10N-6 DB11N-6 DB10N-5 DB11N-5 DB10N-4 DB11N-4 OF- OF+ OF_A N-6 OF_B N-6 OF_A N-5 OF_B N-5 OF_A N-4 OF_B N-4 tSKEW 215765112 TD01 21576512fb 6 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TIMING DIAGRAMS SPI Port Timing (Readback Mode) tDS tS tDH tSCK tH CS SCK tDO SDI SDO R/W A6 A5 A4 A3 A2 A1 A0 XX D7 HIGH IMPEDANCE XX D6 XX D5 XX D4 XX D3 XX D2 XX XX D1 D0 SPI Port Timing (Write Mode) CS SCK SDI SDO R/W A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 21576512 TD02 HIGH IMPEDANCE 21576512fb For more information www.linear.com/LTC2157-12 7 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS LTC2157-12: Integral Nonlinearity (INL) LTC2157-12: Differential Nonlinearity (DNL) LTC2157-12: 32K Point FFT, fIN = 15MHz, -1dBFS, 250Msps 0.50 2.0 0 1.5 -20 DNL ERROR (LSB) INL ERROR (LSB) 0.5 0 -0.5 AMPLITUDE (dBFS) 0.25 1.0 0 0 4095 -0.50 0 4095 -120 LTC2157-12: 32K Point FFT, fIN = 122MHz, -1dBFS, 250Msps 0 -20 -20 -20 -60 -80 -100 AMPLITUDE (dBFS) 0 AMPLITUDE (dBFS) 0 -40 -40 -60 -80 40 60 80 100 FREQUENCY (MHz) 120 -120 0 20 21576512 G04 LTC2157-12: 32K Point FFT, fIN = 229MHz, -1dBFS, 250Msps 120 0 AMPLITUDE (dBFS) -60 -80 0 20 40 60 80 100 FREQUENCY (MHz) 120 21576512 G07 -60 -80 0 20 120 0 LTC2157-12: 32K Point FFT, fIN = 420MHz, -1dBFS, 250MHz -20 -40 -60 -80 -120 40 60 80 100 FREQUENCY (MHz) 21576512 G06 LTC2157-12: 32K Point FFT, fIN = 380MHz, -1dBFS, 250Msps -100 -100 -40 -120 -20 -40 LTC2157-12: 32K Point FFT, fIN = 171MHz, -1dBFS, 250Msps 21576512 G05 -20 -120 40 60 80 100 FREQUENCY (MHz) AMPLITUDE (dBFS) 0 120 -100 -100 20 40 60 80 100 FREQUENCY (MHz) 21576512 G03 LTC2157-12: 32K Point FFT, fIN = 70MHz, -1dBFS, 250Msps 0 20 21576512 G02 21576512 G01 -120 0 OUTPUT CODE OUTPUT CODE AMPLITUDE (dBFS) -80 -100 -1.5 AMPLITUDE (dBFS) -60 -0.25 -1.0 -2.0 -40 -40 -60 -80 -100 0 20 40 60 80 100 FREQUENCY (MHz) 120 21576512 G08 -120 0 20 40 60 80 100 FREQUENCY (MHz) 120 21576512 G09 21576512fb 8 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS 0 -40 -60 -80 -100 -120 0 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 LTC2157-12: 32K Point 2-Tone FFT, fIN = 71.0MHz and 69.0MHz, 250Msps LTC2157-12: 32K Point FFT, fIN = 907MHz, -1dBFS, 250Msps -20 AMPLITUDE (dBFS) 0 LTC2157-12: 32K Point FFT, fIN = 567MHz, -1dBFS, 250Msps -40 -60 -80 -100 0 20 40 60 80 100 FREQUENCY (MHz) -60 -80 -100 -120 120 -40 0 20 40 60 80 100 FREQUENCY (MHz) 21576512 G10 -120 120 0 20 21576512 G27 LTC2157-12: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS 80 20000 120 21576512 G11 LTC2157-12: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2157-12: Shorted Input Histogram 40 60 80 100 FREQUENCY (MHz) 300 18000 70 16000 10000 8000 6000 60 IVDD (mA) IOVDD (mA) 50 40 LVDS CURRENT 1.75mA 4000 2000 0 2048 0 2056 2052 OUTPUT CODE 50 200 250 21576512 G13 LTC2157-12: SFDR vs Input Level, fIN = 70MHz, 1.5V Range, 250Msps 70 dBFS SNR (dBc AND dBFS) 60 40 20 0 70 40 dBc 30 60 50 40 30 20 -70 250 80 50 0 150 200 100 SAMPLE RATE (Msps) 90 dBFS 20 10 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 50 21576512 G14 60 dBc 0 LTC2157-12: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 250Msps LTC2157-12: SNR vs Input Level, fIN = 70MHz, 1.5V Range, 250Msps 120 SFDR (dBFS) 240 220 150 200 100 SAMPLE RATE (Msps) 21576512 G12 80 260 30 SFDR (dBFS) COUNT 12000 100 280 LVDS CURRENT 3.5mA 14000 10 -60 -50 -40 -30 -20 INPUT LEVEL (dBFS) -10 21576512 G16 0 0 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21576512 G17 21576512 G15 21576512fb For more information www.linear.com/LTC2157-12 9 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS LTC2157-12: SNR vs Input Frequency, -1dBFS, 1.5V Range, 250Msps 75 INPUT AMPLITUDE (dBFS) 70 60 55 50 2.0 -1.0 1.5 -1.5 1.0 -2.0 -2.5 -3.0 -3.5 0.5 0 -0.5 -1.0 -4.0 45 40 -0.5 INL ERROR (LSB) SNR (dBFS) 65 LTC2156-12: Integral Nonlinearity (INL) LTC2157-12: Frequency Response -1.5 -4.5 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) -5.0 -2.0 1000 100 INPUT FREQUENCY (MHz) 21576512 G18 0 4095 OUTPUT CODE 21576512 G20 21576512 G19 LTC2156-12: Differential Nonlinearity (DNL) 0.50 0 LTC2156-12: 32K Point FFT, fIN = 15MHz, -1dBFS, 210Msps 0 -20 LTC2156-12: 32K Point FFT, fIN = 71MHz, -1dBFS, 210Msps -20 0 AMPLITUDE (dBFS) AMPLITUDE (dBFS) DNL ERROR (LSB) 0.25 -40 -60 -80 -40 -60 -80 -0.25 -100 -0.50 0 4095 -120 -100 0 20 OUTPUT CODE 40 60 80 FREQUENCY (MHz) 100 -120 0 20 40 60 80 FREQUENCY (MHz) 100 21576512 G21 21576512 G22 0 AMPLITUDE (dBFS) AMPLITUDE (dBFS) 0 -20 -20 -40 -60 -80 0 20 40 60 80 FREQUENCY (MHz) 100 -40 -60 -80 21576512 G24 -120 LTC2156-12: 32K Point FFT, fIN = 227MHz, -1dBFS, 210Msps -20 -100 -100 -120 LTC2156-12: 32K Point FFT, fIN = 171MHz, -1dBFS, 210Msps AMPLITUDE (dBFS) 0 LTC2156-12: 32K Point FFT, fIN = 101MHz, -1dBFS, 210Msps 21576512 G23 -40 -60 -80 -100 0 20 40 60 80 FREQUENCY (MHz) 100 21576512 G25 -120 0 20 40 60 80 FREQUENCY (MHz) 100 21576512 G26 21576512fb 10 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS 0 0 -20 -20 -20 -40 -60 -80 -120 AMPLITUDE (dBFS) 0 -100 -40 -60 -80 -100 0 20 40 60 80 FREQUENCY (MHz) 100 -120 0 20 40 60 80 FREQUENCY (MHz) -60 -80 -120 100 LTC2156-12: 32K Point FFT, fIN = 907MHz, -1dBFS, 210Msps AMPLITUDE (dBFS) -80 40 60 80 FREQUENCY (MHz) 20000 18000 16000 14000 -40 -60 -80 -100 -100 -120 -120 100 LTC2156-12: Shorted Input Histogram -20 -20 -60 20 21576512 G30 0 -40 0 21576512 G29 LTC2156-12: 32K Point 2-Tone FFT, fIN = 70.0MHz and 69.0MHz, 210Msps COUNT 0 -40 -100 21576512 G28 AMPLITUDE (dBFS) LTC2156-12: 32K Point FFT, fIN = 567MHz, -1dBFS, 210Msps LTC2156-12: 32K Point FFT, fIN = 417MHz, -1dBFS, 210Msps AMPLITUDE (dBFS) AMPLITUDE (dBFS) LTC2156-12: 32K Point FFT, fIN = 379MHz, -1dBFS, 210Msps 12000 10000 8000 6000 4000 2000 0 20 40 60 80 FREQUENCY (MHz) 100 0 20 40 60 80 FREQUENCY (MHz) 0 2044 100 2048 2052 OUTPUT CODE 21576512 G32 21576512 G31 LTC2156-12: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS 2056 21576512 G33 LTC2156-12: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2156-12: SFDR vs Input Level, fIN = 70MHz, 1.5V Range, 210Msps 280 120 70 260 LVDS CURRENT 3.5mA 100 dBFS 50 40 SFDR (dBFS) IVDD (mA) IOVDD (mA) 60 240 220 200 20 30 42 dBc 60 40 LVDS CURRENT 1.75mA 0 80 126 168 84 SAMPLE RATE (Msps) 210 21576512 G34 180 0 42 126 168 84 SAMPLE RATE (Msps) 210 21576512 G35 0 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 0 10 21576512 G36 21576512fb For more information www.linear.com/LTC2157-12 11 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS LTC2156-12: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 210Msps LTC2156-12: SNR vs Input Level, fIN = 70MHz, 1.5V Range, 210 Msps 70 dBFS 70 80 70 40 dBc 30 65 60 SNR (dBFS) 50 SFDR (dBFS) SNR (dBc AND dBFS) 75 90 60 50 40 30 20 60 55 50 20 10 0 LTC2156-12: SNR vs Input Frequency, -1dBFS, 1.5V Range, 210Msps 45 10 -70 -60 -50 -40 -30 -20 INPUT LEVEL (dBFS) -10 0 0 21576512 G37 40 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21576512 G38 2.0 -1.0 1.5 -1.5 1.0 INL ERROR (LSB) -3.0 -3.5 0.50 0.25 DNL ERROR (LSB) INPUT AMPLITUDE (dBFS) -0.5 -2.5 LTC2155-12: Differential Nonlinearity (DNL) LTC2155-12: Integral Nonlinearity (INL) LTC2156-12: Frequency Response -2.0 21576512 G39 0.5 0 -0.5 -0.25 -1.0 -4.0 0 -1.5 -4.5 -5.0 -2.0 1000 100 INPUT FREQUENCY (MHz) 0 4095 -0.50 0 4095 OUTPUT CODE OUTPUT CODE 21576512 G42 21576512 G41 21576512 G40 0 -40 -60 -80 -100 -120 0 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 LTC2155-12: 32K Point FFT, fIN = 70MHz, -1dBFS, 170Msps -40 -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21576512 G43 -120 LTC2155-12: 32K Point FFT, fIN = 121MHz, -1dBFS, 170Msps -20 AMPLITUDE (dBFS) 0 LTC2155-12: 32K Point FFT, fIN = 15MHz, -1dBFS, 170Msps -40 -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21576512 G44 -120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 21576512 G45 21576512fb 12 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 -40 -60 -80 -100 -120 0 0 -20 -20 AMPLITUDE (dBFS) 0 LTC2155-12: 32K Point FFT, fIN = 225MHz, -1dBFS, 170Msps LTC2155-12: 32K Point FFT, fIN = 176MHz, -1dBFS, 170Msps -40 -60 -80 -100 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 -120 80 0 0 10 20 30 40 50 60 FREQUENCY (MHz) -100 10 20 30 40 50 60 FREQUENCY (MHz) 70 -60 -80 -120 80 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 20 30 40 50 60 FREQUENCY (MHz) 70 80 21576512 G52 80 LTC2155-12: 32K Point FFT, fIN = 907MHz, -1dBFS, 170Msps -60 -80 0 10 20 30 40 50 60 FREQUENCY (MHz) 80 21576512 G51 20000 70 18000 65 16000 60 LVDS CURRENT 3.5mA 55 12000 10000 8000 50 45 40 4000 35 2000 30 0 2056 70 LTC2155-12: IOVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS 6000 10 70 -40 -120 IOVDD (mA) COUNT AMPLITUDE (dBFS) 0 14000 -40 0 30 40 50 60 FREQUENCY (MHz) 21576512 G48 LTC2155-12: Shorted Input Histogram -20 -100 20 21576512 G50 0 -80 10 -100 21576512 G49 -60 0 -20 -100 0 -80 -120 LTC2155-12: 32K Point FFT, fIN = 567MHz, -1dBFS, 170Msps -40 LTC2155-12: 32K Point 2-Tone FFT, fIN = 70.0MHz and 69.0MHz, 170Msps -120 80 AMPLITUDE (dBFS) -80 -120 70 -20 AMPLITUDE (dBFS) AMPLITUDE (dBFS) -20 -60 -60 21576512 G47 LTC2155-12: 32K Point FFT, fIN = 420MHz, -1dBFS, 170Msps -40 -40 -100 21576512 G46 0 LTC2155-12: 32K Point FFT, fIN = 380MHz, -1dBFS, 170Msps 2060 OUTPUT CODE 2064 21576512 G53 25 LVDS CURRENT 1.75mA 0 34 136 102 68 SAMPLE RATE (Msps) 170 21576512 G54 21576512fb For more information www.linear.com/LTC2157-12 13 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL PERFORMANCE CHARACTERISTICS LTC2155-12: IVDD vs Sample Rate, 15MHz Sine Wave Input, -1dBFS LTC2155-12: SFDR vs Input Level, fIN = 70MHz, 1.5V Range, 170Msps LTC2155-12: SNR vs Input Level, fIN = 70MHz, 1.5V Range, 170Msps 260 230 80 220 210 dBc 60 20 190 0 34 102 136 68 SAMPLE RATE (Msps) 21576512 G55 0 65 SNR (dBFS) 60 55 50 21576512 G38 -10 0 21576512 G57 40 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 45 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) -50 -40 -30 -20 INPUT LEVEL (dBFS) -1.0 20 0 -60 LTC2155-12: Frequency Response INPUT AMPLITUDE (dBFS) 70 10 -70 -0.5 70 80 30 20 LTC2155-12: SNR vs Input Frequency, -1dBFS, 1.5V Range, 170Msps 90 40 dBc 30 0 10 75 50 40 21576512 G56 LTC2155-12: SFDR vs Input Frequency, -1dBFS, 1.5V Range, 170Msps 60 50 10 0 -80 -70 -60 -50 -40 -30 -20 -10 AMPLITUDE (dBFS) 170 dBFS 60 40 200 SFDR (dBFS) dBFS SNR (dBc AND dBFS) 100 SFDR (dBFS) IVDD (mA) 240 180 70 120 250 -4.5 0 100 200 300 400 500 600 700 800 900 1000 INPUT FREQUENCY (MHz) 21576512 G59 -5.0 1000 100 INPUT FREQUENCY (MHz) 21576512 G60 21576512fb 14 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 PIN FUNCTIONS VDD (Pins 1, 2, 15, 16, 17, 64): 1.8V Analog Power Supply. Bypass to ground with 0.1F ceramic capacitors. Pins 1, 2, 64 can share a bypass capacitor. Pins 15, 16, 17 can share a bypass capacitor. GND (Pins 3, 6, 9, 11, 14, 18, 21, 58, Exposed Pad Pin 65): ADC Power Ground. The exposed pad must be soldered to the PCB ground. AINA+ (Pin 4): Positive Differential Analog Input for Channel A. AINA- (Pin 5): Negative Differential Analog Input for Channel A. SENSE (Pin 7): Reference Programming Pin. Connecting SENSE to VDD selects the internal reference and a 0.75V input range. An external reference between 1.2V and 1.3V applied to SENSE selects an input range of 0.6 x VSENSE. VREF (Pin 8): Reference Voltage Output. Bypass to ground with a 2.2F ceramic capacitor. Nominally 1.25V. VCM (Pin 10): Common Mode Bias Output; nominally equal to 0.435 * VDD. VCM should be used to bias the common mode of the analog inputs. Bypass to ground with a 0.1F ceramic capacitor. AINB- (Pin 12): Negative Differential Analog Input for Channel B. AINB+ (Pin 13): Positive Differential Analog Input for Channel B. ENC+ (Pin 19): Encode Input. Conversion starts on the rising edge. ENC- (Pin 20): Encode Complement Input. Conversion starts on the falling edge. NC (Pins 24, 25, 42, 43): Not Connected. OGND (Pins 33, 48): Output Driver Ground. OVDD (Pins 32, 49): 1.8V Output Driver Supply. Bypass each pin to ground with separate 0.1F ceramic capacitors. SDO (Pin 59): Serial Interface Data Output. In serial programming mode, (PAR/SER = 0V), SDO is the optional serial interface data output. Data on SDO is read back from the mode control registers and can be latched on the falling edge of SCK. SDO is an open-drain N-channel MOSFET output that requires an external 2k pull-up resistor from 1.8V to 3.3V. If readback from the mode control registers is not needed, the pull-up resistor is not necessary and SDO can be left unconnected. SDI (Pin 60): Serial Interface Data Input. In serial programming mode, (PAR/SER = 0V), SDI is the serial interface data input. Data on SDI is clocked into the mode control registers on the rising edge of SCK. In the parallel programming mode (PAR/SER = VDD), SDI selects 3.5mA or 1.75mA LVDS output current (see Table 2). SDI can be driven with 1.8V to 3.3V logic. SCK (Pin 61): Serial Interface Clock Input. In serial programming mode, (PAR/SER = 0V), SCK is the serial interface clock input. In the parallel programming mode (PAR/SER = VDD), SCK can be used to place the part in the low power sleep mode (see Table 2). SCK can be driven with 1.8V to 3.3V logic. CS (Pin 62): Serial Interface Chip Select Input. In serial programming mode, (PAR/SER = 0V), CS is the serial interface chip select input. When CS is low, SCK is enabled for shifting data on SDI into the mode control registers. In the parallel programming mode (PAR/SER = VDD), CS controls the clock duty cycle stabilizer (see Table 2). CS can be driven with 1.8V to 3.3V logic. PAR/SER (Pin 63): Programming Mode Selection Pin. Connect to ground to enable the serial programming mode where CS, SCK, SDI, SDO become a serial interface that control the A/D operating modes. Connect to VDD to enable the parallel programming mode where CS, SCK, SDI become parallel logic inputs that control a reduced set of the A/D operating modes. PAR/SER should be connected directly to ground or the VDD of the part and not be driven by a logic signal. 21576512fb For more information www.linear.com/LTC2157-12 15 LTC2157-12/ LTC2156-12/LTC2155-12 PIN FUNCTIONS CLKOUT -/CLKOUT+ (Pins 40/41): Data Output Clock. The digital outputs normally transition at the same time as the falling and rising edges of CLKOUT+. The phase of CLKOUT+ can also be delayed relative to the digital outputs by programming the mode control registers. LVDS Outputs The following pins are differential LVDS outputs. The output current level is programmable. There is an optional internal 100 termination resistor between the pins of each LVDS output pair. DA0_1-/DA0_1+ to DA10_11-/DA10_11+ (Pins 44/45, 46/47, 50/51, 52/53, 54/55, 56/57): Channel A Double-Data Rate Digital Outputs. Two data bits are multiplexed onto each differential output pair. The even data bits (DA0, DA2, DA4, DA6, DA8, DA10) appear when CLKOUT+ is low. The odd data bits (DA1, DA3, DA5, DA7, DA9, DA11) appear when CLKOUT+ is high. OF-/OF+ (Pins 22/23): Over/Underflow Digital Output. OF+ is high when an overflow or underflow has occurred. The overflows for channel A and channel B are multiplexed together. DB0_1-/DB0_1+ to DB10_11-/DB10_11+ (Pins 26/27, 28/29, 30/31, 34/35, 36/37, 38/39): Channel B Double-Data Rate Digital Outputs. Two data bits are multiplexed onto each differential output pair. The even data bits (DB0, DB2, DB4, DB6, DB8, DB10) appear when CLKOUT+ is low. The odd data bits (DB1, DB3, DB5, DB7, DB9, DB11) appear when CLKOUT+ is high. FUNCTIONAL BLOCK DIAGRAM VDD OVDD CHANNEL A ANALOG INPUT 12-BIT PIPELINED ADC CORE S/H VCM 0.1F CORRECTION LOGIC DA10_11 * * * DA0_1 OUTPUT DRIVERS VCM BUFFER DDR LVDS OGND BUFFER GND CLOCK CLOCK/DUTY CYCLE CONTROL CS SCK SDI PAR/SER SPI VREF 2.2F 1.25V REFERENCE GND RANGE SELECT SENSE ANALOG INPUT BUFFER S/H OVDD 12-BIT PIPELINED ADC CORE CORRECTION LOGIC DB10_11 * * * DB0_1 OUTPUT DRIVERS DDR LVDS CHANNEL B 21576512 F01 GND OGND Figure 1. Functional Block Diagram 21576512fb 16 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION CONVERTER OPERATION INPUT DRIVE CIRCUITS The LTC2157-12/LTC2156-12/LTC2155-12 are twochannel, 12-bit 250Msps/210Msps/170Msps A/D converters that are powered by a single 1.8V supply. The analog inputs must be driven differentially. The encode inputs should be driven differentially for optimal performance. The digital outputs are double-data rate LVDS. Additional features can be chosen by programming the mode control registers through a serial SPI port. ANALOG INPUT The analog inputs are differential CMOS sample-andhold circuits (Figure 2). The inputs must be driven differentially around a common mode voltage set by the VCM output pin, which is nominally 0.435 * VDD. For the 1.5V input range, the inputs should swing from VCM - 0.375V to VCM + 0.375V. There should be 180 phase difference between the inputs. Input Filtering If possible, there should be an RC lowpass filter right at the analog inputs. This lowpass filter isolates the drive circuitry from the A/D sample-and-hold switching, and also limits wide band noise from the drive circuitry. Figure 3 shows an example of an input RC filter. The RC component values should be chosen based on the application's specific input frequency. Transformer-Coupled Circuits Figure 3 shows the analog input being driven by an RF transformer with the common mode supplied through a pair of resistors via the VCM pin. At higher input frequencies a transmission line balun transformer (Figures 4 and 5) has better balance, resulting in lower A/D distortion. The two channels are simultaneously sampled by a shared encode circuit. 10 VCM 0.1F 0.1F LTC2157-12 VDD IN RON 20 AIN+ T1 1:1 4.7 AIN+ 25 2pF 2pF 10pF 0.1F 4.7 25 AIN- VDD RON 20 AIN- LTC2157-12 T1: MACOM ETC1-1T 2pF 21576512 F03 Figure 3. Analog Input Circuit Using a Transformer. Recommended for Input Frequencies from 5MHz to 70MHz 2pF VDD 10 1.2V VCM 0.1F 0.1F 10k ENC+ LTC2157-12 4.7 IN AIN+ 45 ENC- 0.1F 0.1F 45 21576512 F02 Figure 2. Equivalent Input Circuit. Only One of Two Analog Channels Is Shown 100 4.7 AIN- T1: MABA T2: WBC1-1L 007159-000000 21576512 F04 Figure 4. Recommended Front-End Circuit for Input Frequencies from 15MHz to 150MHz 21576512fb For more information www.linear.com/LTC2157-12 17 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION VCM 10 0.1F 50 LTC2157-12 0.1F 4.7 IN LTC2157-12 AIN+ 3pF 0.1F 45 4.7 INPUT 0.1F 100 0.1F 45 0.1F 4.7 T1: MABA 007159-000000 VCM 0.1F 50 4.7 3pF AIN+ AIN- 3pF AIN- 21576512 F06 21576514 F05 Figure 6. Front-End Circuit Using a High Speed Differential Amplifier Figure 5. Recommended Front-End Circuit for Input Frequencies from 150MHz Up to 900MHz 5 VREF Amplifier Circuits 1.25V 2.2F Figure 6 shows the analog input being driven by a high speed differential amplifier. The output of the amplifier is AC coupled to the A/D so the amplifier's output common mode voltage can be optimally set to minimize distortion. SCALER/ BUFFER SENSE SENSE DETECTOR At very high frequencies an RF gain block will often have lower distortion than a differential amplifier. If the gain block is single-ended, then a transformer circuit (Figures 3 and 5) should convert the signal to differential before driving the A/D. The A/D cannot be driven single ended. 21576512 F07 Figure 7. Reference Circuit LTC2157-12 Reference The LTC2157-12/LTC2156-12/LTC2155-12 has an internal 1.25V voltage reference. For a 1.5V input range with internal reference, connect SENSE to VDD. For a 1.5V input range with an external reference, apply a 1.25V reference voltage to SENSE (Figure 7). Encode Input ADC REFERENCE VDD 1.2V ENC+ 10k ENC- The signal quality of the encode inputs strongly affects the A/D noise performance. The encode inputs should be treated as analog signals--do not route them next to digital traces on the circuit board. The encode inputs are internally biased to 1.2V through 10k equivalent resistance (Figure 8). If the common mode of the driver is within 1.1V to 1.5V, it is possible to drive 21576512 F08 Figure 8. Equivalent Encode Input Circuit the encode inputs directly. Otherwise a transformer or coupling capacitors are needed (Figures 9 and 10). The maximum (peak) voltage of the input signal should never exceed VDD +0.1V or go below -0.1V. 21576512fb 18 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION LTC2157-12 VDD 1.2V 0.1F 10k 50 T1 100 0.1F 50 21576512 F09 T1: MACOM ETC1-1-13 Figure 9. Sinusoidal Encode Drive LTC2157-12 VDD 1.2V 0.1F PECL OR LVDS INPUT ENC+ 10k 100 0.1F ENC- 21576512 F10 Figure 10. PECL or LVDS Encode Drive Clock Duty Cycle Stabilizer DIGITAL OUTPUTS For good performance the encode signal should have a 50% (5%) duty cycle. If the optional clock duty cycle stabilizer circuit is enabled, the encode duty cycle can vary from 30% to 70% and the duty cycle stabilizer will maintain a constant 50% internal duty cycle. The duty cycle stabilizer is enabled via SPI Register A2 (see Table 3) or by CS in parallel programming mode. The digital outputs are double-data rate LVDS signals. Two data bits are multiplexed and output on each differential output pair. There are six LVDS output pairs for channel A (DA0_1+/DA0_1- through DA10_11-/DA10_11+) and six pairs for channel B (DB0_1+/DB0_1- through DB10_11-/ DB10_11+). Overflow (OF+/OF -) and the data output clock (CLKOUT+/CLKOUT-) each have an LVDS output pair. Note that overflow for both channels is multiplexed onto the OF+/OF - output pair. For applications where the sample rate needs to be changed quickly, the clock duty cycle stabilizer can be disabled. In this case care should be taken to make the clock a 50% (5%) duty cycle. 21576512fb For more information www.linear.com/LTC2157-12 19 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION By default the outputs are standard LVDS levels: 3.5mA output current and a 1.25V output common mode voltage. An external 100 differential termination resistor is required for each LVDS output pair. The termination resistors should be located as close as possible to the LVDS receiver. The outputs are powered by OVDD and OGND which are isolated from the A/D core power and ground. Programmable LVDS Output Current The default output driver current is 3.5mA. This current can be adjusted by serially programming mode control register A3 (see Table 3). Available current levels are 1.75mA, 2.1mA, 2.5mA, 3mA, 3.5mA, 4mA and 4.5mA. Optional LVDS Driver Internal Termination In most cases, using just an external 100 termination resistor will give excellent LVDS signal integrity. In addition, an optional internal 100 termination resistor can be enabled by serially programming mode control register A3. The internal termination helps absorb any reflections caused by imperfect termination at the receiver. When the internal termination is enabled, the output driver current is doubled to maintain the same output voltage swing. Overflow Bit The overflow output bit (OF) outputs a logic high when the analog input is either overranged or underranged. The overflow bit has the same pipeline latency as the data bits. The OF output is double-data rate; when CLKOUT+ is low, channel A's overflow is available; when CLKOUT+ is high, channel B's overflow is available. Phase Shifting the Output Clock To allow adequate set-up and hold time when latching the output data, the CLKOUT+ signal may need to be phase shifted relative to the data output bits. Most FPGAs have this feature; this is generally the best place to adjust the timing. Alternatively, the ADC can also phase shift the CLKOUT+/ CLKOUT- signals by serially programming mode control register A2. The output clock can be shifted by 0, 45, 90, or 135. To use the phase shifting feature the clock duty cycle stabilizer must be turned on. Another control register bit can invert the polarity of CLKOUT+ and CLKOUT-, independently of the phase shift. The combination of these two features enables phase shifts of 45 up to 315 (Figure 11). ENC+ D0-D11, OF CLKOUT+ MODE CONTROL BITS PHASE SHIFT CLKINV CLKPHASE1 CLKPHASE0 0 0 0 0 45 0 0 1 90 0 1 0 135 0 1 1 180 1 0 0 225 1 0 1 270 1 1 0 315 1 1 1 21576512 F11 Figure 11. Phase Shifting CLKOUT 21576512fb 20 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION DATA FORMAT CLKOUT Table 1 shows the relationship between the analog input voltage, the digital data output bits and the overflow bit. By default the output data format is offset binary. The 2's complement format can be selected by serially programming mode control register A4. OF OF D11 Table 1. Output Codes vs Input Voltage AIN+ - AIN- CLKOUT D11/D0 D10 (1.5V Range) OF D11-D0 (OFFSET BINARY) D11-D0 (2's COMPLEMENT) >0.75 V 1 1111 1111 1111 0111 1111 1111 +0.75V 0 1111 1111 1111 0111 1111 1111 +0.7496337V 0 1111 1111 1110 0111 1111 1110 +0.0003662V 0 1000 0000 0001 0000 0000 0001 +0.000000V 0 1000 0000 0000 0000 0000 0000 -0.0003662V 0 0111 1111 1111 1111 1111 1111 -0.0007324V 0 0111 1111 1110 1111 1111 1110 -0.74963378V 0 0000 0000 0001 1000 0000 0001 -0.75V 0 0000 0000 0000 1000 0000 0000 < -0.75V 1 0000 0000 0000 1000 0000 0000 D10/D0 * * * RANDOMIZER ON D1 D1/D0 D0 D0 21576512 F12 Figure 12. Functional Equivalent of Digital Output Randomizer PC BOARD CLKOUT FPGA Digital Output Randomizer Interference from the A/D digital outputs is sometimes unavoidable. Digital interference may be from capacitive or inductive coupling or coupling through the ground plane. Even a tiny coupling factor can cause unwanted tones in the ADC output spectrum. By randomizing the digital output before it is transmitted off chip, these unwanted tones can be randomized which reduces the unwanted tone amplitude. The digital output is randomized by applying an exclusiveOR logic operation between the LSB and all other data output bits. To decode, the reverse operation is applied--an exclusive-OR operation is applied between the LSB and all other bits. The LSB, OF and CLKOUT outputs are not affected. The output randomizer is enabled by serially programming mode control register A4. OF D11/D0 LTC2157-12 D11 D10/D0 D1/D0 D0 * * * D10 D1 D0 21576512 F13 Figure 13. Decoding a Randomized Digital Output Signal 21576512fb For more information www.linear.com/LTC2157-12 21 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION Alternate Bit Polarity Sleep Mode Another feature that may reduce digital feedback on the circuit board is the alternate bit polarity mode. When this mode is enabled, all of the odd bits (D1, D3, D5, D7, D9, D11) are inverted before the output buffers. The even bits (D0, D2, D4, D6, D8, D10), OF and CLKOUT are not affected. This can reduce digital currents in the circuit board ground plane and reduce digital noise, particularly for very small analog input signals. The A/D may be placed in a power-down mode to conserve power. In sleep mode the entire A/D converter is powered down, resulting in < 5mW power consumption. If the encode input signal is not disabled the power consumption will be higher (up to 5mW at 250Msps). Sleep mode is enabled by mode control register A1 (serial programming mode), or by SCK (parallel programming mode). In the serial programming mode it is also possible to disable channel B while leaving channel A in normal operation. The digital output is decoded at the receiver by inverting the odd bits (D1, D3, D5, D7, D9, D11). The alternate bit polarity mode is independent of the digital output randomizer--either both or neither function can be on at the same time. The alternate bit polarity mode is enabled by serially programming mode control register A4. The amount of time required to recover from sleep mode depends on the size of the bypass capacitors on VREF . For the suggested values in Figure 1, the A/D will stabilize after 0.1ms + 2500 * tp where tp is the period of the sampling clock. Digital Output Test Patterns Nap Mode To allow in-circuit testing of the digital interface to the A/D, there are several test modes that force the A/D data outputs (OF, D11 to D0) to known values: In nap mode the A/D core is powered down while the internal reference circuits stay active, allowing faster wakeup. Recovering from nap mode requires at least 100 clock cycles. Wake-up time from nap mode is guaranteed only if the clock is kept running, otherwise sleep mode wake-up conditions apply. Nap mode is enabled by setting register A1 in the serial programming mode. All 1s: All outputs are 1 All 0s: All outputs are 0 Alternating: Outputs change from all 1s to all 0s on alternating samples Checkerboard: Outputs change from 1010101010101 to 0101010101010 on alternating samples. The digital output test patterns are enabled by serially programming mode control register A4. When enabled, the test patterns override all other formatting modes: 2's complement, randomizer, alternate-bit polarity. Output Disable The digital outputs may be disabled by serially programming mode control register A3. All digital outputs including OF and CLKOUT are disabled. The high impedance disabled state is intended for long periods of inactivity, it is not designed for multiplexing the data bus between multiple converters. DEVICE PROGRAMMING MODES The operating modes of the LTC215x-12 can be programmed by either a parallel interface or a simple serial interface. The serial interface has more flexibility and can program all available modes. The parallel interface is more limited and can only program some of the more commonly used modes. Parallel Programming Mode To use the parallel programming mode, PAR/SER should be tied to VDD. The CS, SCK and SDI pins are binary logic inputs that set certain operating modes. These pins can be tied to VDD or ground, or driven by 1.8V, 2.5V, or 3.3V CMOS logic. Table 2 shows the modes set by CS, SCK and SDI. 21576512fb 22 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD) PIN DESCRIPTION CS Clock Duty Cycle Stabilizer Control Bit 0 = Clock Duty Cycle Stabilizer Off 1 = Clock Duty Cycle Stabilizer On SCK Power Down Control Bit 0 = Normal Operation 1 = Sleep Mode (entire ADC is powered down) SDI LVDS Current Selection Bit 0 = 3.5mA LVDS Current Mode 1 = 1.75mA LVDS Current Mode Software Reset If serial programming is used, the mode control registers should be programmed as soon as possible after the power supplies turn on and are stable. The first serial command must be a software reset which will reset all register data bits to logic 0. To perform a software reset it is necessary to write 1 in register A0 (Bit D7). After the reset is complete, Bit D7 is automatically set back to zero. This register is WRITE-ONLY. GROUNDING AND BYPASSING Serial Programming Mode To use the serial programming mode, PAR/SER should be tied to ground. The CS, SCK, SDI and SDO pins become a serial interface that program the A/D control registers. Data is written to a register with a 16-bit serial word. Data can also be read back from a register to verify its contents. Serial data transfer starts when CS is taken low. The data on the SDI pin is latched at the first sixteen rising edges of SCK. Any SCK rising edges after the first sixteen are ignored. The data transfer ends when CS is taken high again. The first bit of the 16-bit input word is the R/W bit. The next seven bits are the address of the register (A6:A0). The final eight bits are the register data (D7:D0). If the R/W bit is low, the serial data (D7:D0) will be written to the register set by the address bits (A6:A0). If the R/W bit is high, data in the register set by the address bits (A6:A0) will be read back on the SDO pin (see the Timing Diagrams). During a readback command the register is not updated and data on SDI is ignored. The SDO pin is an open-drain output that pulls to ground with a 200 impedance. If register data is read back through SDO, an external 2k pull-up resistor is required. If serial data is only written and readback is not needed, then SDO can be left floating and no pull-up resistor is needed. Table 3 shows a map of the mode control registers. The LTC215x-12 requires a printed circuit board with a clean unbroken ground plane in the first layer beneath the ADC. A multilayer board with an internal ground plane is recommended. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track or underneath the ADC. High quality ceramic bypass capacitors should be used at the VDD, OVDD, VCM, VREF pins. Bypass capacitors must be located as close to the pins as possible. Size 0402 ceramic capacitors are recommended. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as possible. The analog inputs, encode signals, and digital outputs should not be routed next to each other. Ground fill and grounded vias should be used as barriers to isolate these signals from each other. HEAT TRANSFER Most of the heat generated by the LTC215x-12 is transferred from the die through the bottom-side exposed pad and package leads onto the printed circuit board. For good electrical and thermal performance, the exposed pad must be soldered to a large grounded pad on the PC board. This pad should be connected to the internal ground planes by an array of vias. 21576512fb For more information www.linear.com/LTC2157-12 23 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION Table 3. Serial Programming Mode Register Map (PAR/SER = GND). An "X" Indicates Unused Bit REGISTER A0: RESET REGISTER (ADDRESS 00h) WRITE-ONLY D7 D6 D5 D4 D3 D2 D1 D0 RESET X X X X X X X RESET Bit 7 Software Reset Bit 0 = Reset Disabled 1 = Software Reset. All mode control registers are reset to 00h. This bit is automatically set back to zero after the reset is complete. Bits 6-0 Unused bits REGISTER A1: POWER-DOWN REGISTER (ADDRESS 01h) D7 D6 D5 D4 D3 D2 D1 D0 X X X X SLEEP NAP PDB 0 Bits 7-4 Unused, these bits are read back as 0 Bit 3 SLEEP 0 = Normal Operation 1 = Power Down Entire ADC Bit 2 NAP 0 = Normal Mode 1 = Low Power Mode for Both Channels PDB Bit 1 0 = Normal Operation 1 = Power Down Channel B. Channel A operates normally. Bit 0 Must be set to 0 REGISTER A2: TIMING REGISTER (ADDRESS 02h) D7 D6 D5 D4 D3 D2 D1 D0 X X X X CLKINV CLKPHASE1 CLKPHASE0 DCS Bits 7-4 Unused, these bits are read back as 0 Bit 3 CLKINV Output Clock Invert Bit 0 = Normal CLKOUT Polarity (as shown in the Timing Diagrams) 1 = Inverted CLKOUT Polarity Bits 2-1 CLKPHASE1:CLKPHASE0 Output Clock Phase Delay Bits 00 = No CLKOUT Delay (as shown in the Timing Diagrams) 01 = CLKOUT+/CLKOUT- delayed by 45 (Clock Period * 1/8) 10 = CLKOUT+/CLKOUT- delayed by 90 (Clock Period * 1/4) 11 = CLKOUT+/CLKOUT- delayed by 135 (Clock Period * 3/8) Note: If the CLKOUT phase delay feature is used, the clock duty cycle stabilizer must also be turned on. Bit 0 DCS Clock Duty Cycle Stabilizer Bit 0 = Clock Duty Cycle Stabilizer Off 1 = Clock Duty Cycle Stabilizer On 21576512fb 24 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 APPLICATIONS INFORMATION REGISTER A3: OUTPUT MODE REGISTER (ADDRESS 03h) D7 X D6 D5 D4 D3 D2 D1 D0 X X ILVDS2 ILVDS1 ILVDS0 TERMON OUTOFF Bits 7-5 Unused, these bits are read back as 0 Bits 4-2 ILVDS2:ILVDS0 LVDS Output Current Bits 000 = 3.5mA LVDS Output Driver Current 001 = 4.0mA LVDS Output Driver Current 010 = 4.5mA LVDS Output Driver Current 011 = Not Used 100 = 3.0mA LVDS Output Driver Current 101 = 2.5mA LVDS Output Driver Current 110 = 2.1mA LVDS Output Driver Current 111 = 1.75mA LVDS Output Driver Current Bit 1 TERMON LVDS Internal Termination Bit 0 = Internal Termination Off 1 = Internal Termination On. LVDS output driver current is 2x the current set by ILVDS2:ILVDS0 Bit 0 OUTOFF Digital Output Mode Control Bits 0 = Digital Outputs Are Enabled 1 = Digital Outputs Are Disabled (High Impedance) REGISTER A4: DATA FORMAT REGISTER (ADDRESS 04h) D7 OUTTEST2 Bits 7-5 D6 D5 D4 D3 D2 D1 D0 OUTTEST1 OUTTEST0 ABP 0 DTESTON RAND TWOSCOMP OUTTEST2:OUTTEST0 Digital Output Test Pattern Bits 000 = All Digital Outputs = 0 001 = All Digital Outputs = 1 010 = Alternating Output Pattern. OF, D11-D0 alternate between 0 0000 0000 0000 and 1 1111 1111 1111 100 = Checkerboard Output Pattern. OF, D11-D0 alternate between 1 0101 0101 0101 and 0 1010 1010 1010 Note 1: Other bit combinations are not used. Note 2: Patterns from channel A and channel B may not be synchronous. Bit 4 ABP Alternate Bit Polarity Mode Control Bit 0 = Alternate Bit Polarity Mode Off 1 = Alternate Bit Polarity Mode On Bit 3 Must be set to 0 Bit 2 DTESTON Enable the digital output test patterns (set by Bits 7-5) 0 = Normal Mode 1 = Enable the Digital Output Test Patterns Bit 1 RAND Data Output Randomizer Mode Control Bit 0 = Data Output Randomizer Mode Off 1 = Data Output Randomizer Mode On Bit 0 TWOSCOMP Two's Complement Mode Control Bit 0 = Offset Binary Data Format 1 = Two's Complement Data Format 21576512fb For more information www.linear.com/LTC2157-12 25 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL APPLICATIONS Silkscreen Top Top Side 21576512fb 26 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL APPLICATIONS Inner Layer 2 GND Inner Layer 3 21576512fb For more information www.linear.com/LTC2157-12 27 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL APPLICATIONS Inner Layer 4 Inner Layer 5 Bottom Side 21576512fb 28 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL APPLICATIONS LTC2157-12 Schematic VDD C7 0.1F C5 0.1F C12 0.1F PAR/SER VDD AINA AINA- R34 10 C27 1pF R33 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 65 SENSE R8 100 C4 2.2F C29 0.1F - AINB R7 10 C3 1pF R6 10 R12 100 LTC2157-12 OGND DA2_3+ DA2_3- DA0_1+ DA0_1- NC NC CLKOUT+ CLKOUT- DB10_11+ DB10_11- DB8_9+ DB8_9- DB6_7+ DB6_7- OGND 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 AINB+ VDD VDD GND AINA+ AINA- GND SENSE VREF GND VCM GND AINB- AINB+ GND VDD VDD GND VDD C13 0.1F 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 DA2_3+ DA2_3- DA0_1+ DA0_1- CLKOUT+ CLKOUT- DB10_11+ DB10_11- DB8_9+ DB8_9- DB6_7+ DB6_7- VDD GND ENC+ ENC- GND OF- OF+ NC NC DB0_1- DB0_1+ DB2_3- DB2_3+ DB4_5- DB4_5+ OVDD + OVDD VDD PAR_SER CS SCK SDI SDO GND DA10_11+ DA10_11- DA8_9+ DA8_9- DA6_7+ DA6_7- DA4_5+ DA4_5- OVDD 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 C11 0.1F DA10_11+ DA10_11- DA8_9+ DA8_9- DA6_7+ DA6_7- DA4_5+ DA4_5- SDO SDI SCK CS OVDD C15 0.1F R56 100 C14 0.1F C78 0.1F ENC+ C79 0.1F ENC- 21576512 TA11 DB4_5+ DB4_5- DB2_3+ DB2_3- DB0_1+ DB0_1- OF+ OF- 21576512fb For more information www.linear.com/LTC2157-12 29 LTC2157-12/ LTC2156-12/LTC2155-12 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UP Package 64-Lead Plastic QFN (9mm x 9mm) (Reference LTC DWG # 05-08-1705 Rev C) 0.70 0.05 7.15 0.05 7.50 REF 8.10 0.05 9.50 0.05 (4 SIDES) 7.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 9 .00 0.10 (4 SIDES) 0.75 0.05 R = 0.10 TYP R = 0.115 TYP 63 64 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 5) 1 2 PIN 1 CHAMFER C = 0.35 7.50 REF (4-SIDES) 7.15 0.10 7.15 0.10 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION WNJR-5 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 4. EXPOSED PAD SHALL BE SOLDER PLATED 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 6. DRAWING NOT TO SCALE (UP64) QFN 0406 REV C 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD 21576512fb 30 For more information www.linear.com/LTC2157-12 LTC2157-12/ LTC2156-12/LTC2155-12 REVISION HISTORY REV DATE DESCRIPTION A 12/14 Changed the pipeline latency to 6 PAGE NUMBER B 07/15 Updated G16, G37 and G57 Correcting the connection of SENSE in the schematic 5 and 6 9, 12 and 14 29 21576512fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of itsinformation circuits as described herein will not infringe on existing patent rights. For more www.linear.com/LTC2157-12 31 LTC2157-12/ LTC2156-12/LTC2155-12 TYPICAL APPLICATION LTC2157-12: 32K Points 2-Tone FFT, fIN = 71MHz and 69MHz, 250Msps VDD OVDD ANALOG INPUT CLOCK ANALOG INPUT S/H 12-BIT PIPELINED ADC CORE OUTPUT DRIVERS DA10_11 * * * DA0_1 0 DDR LVDS OGND CLOCK/DUTY CYCLE CONTROL S/H CORRECTION LOGIC OVDD CHANNEL B 12-BIT PIPELINED ADC CORE CORRECTION LOGIC OUTPUT DRIVERS DB10_11 * * * DB0_1 -20 AMPLITUDE (dBFS) CHANNEL A -40 -60 -80 -100 DDR LVDS -120 0 20 GND 40 60 80 100 FREQUENCY (MHz) 120 21576512 G11 21576512 TA01 OGND RELATED PARTS PART NUMBER DESCRIPTION COMMENTS 16-Bit, 130Msps, 3.3V ADC, LVDS Outputs 1250mW, 77.7dB SNR, 100dB SFDR, 64-Lead QFN Package ADCs LTC2208 LTC2157-14/ 14-Bit, 250Msps/210Msps/170Msps, 1.8V Dual ADC, DDR LTC2156-14/ LVDS Output LTC2155-14 650mW/616mW/567mW, 70dB SNR, 90dB SFDR, 64-Lead QFN Package LTC2242-12/ 12-Bit, 250Msps/210Msps/170Msps, 2.5V ADC, LVDS LTC2241-12/ Outputs LTC2240-12 740mW/585mW/445mW, 68.5dB SNR, 80dB SFDR, 64-Lead QFN LTC2220 890mW, 67.7dB SNR, 80dB SFDR, 64-Lead QFN 12-Bit, 170Msps, 3.3V, LVDS Outputs LTC2262-14 14-Bit, 150Msps 1.8V ADC, Ultralow Power 149mW, 72.8dB SNR, 88dB SFDR, DDR LVDS/DDR CMOS/CMOS Outputs, 40-Lead QFN Package RF Mixers/Demodulators LT(R)5517 40MHz to 900MHz Direct Conversion Quadrature Demodulator High IIP3: 21dBm at 800MHz, Integrated LO Quadrature Generator LT5527 400MHz to 3.7GHz High Linearity Downconverting Mixer 24.5dBm IIP3 at 900MHz, 23.5dBm IIP3 at 3.5GHz, NF = 12.5dB, 50 Single-Ended RF and LO Ports LT5575 800MHz to 2.7GHz Direct Conversion Quadrature Demodulator High IIP3: 28dBm at 900MHz, Integrated LO Quadrature Generator, Integrated RF and LO Transformer Amplifiers/Filters LTC6409 10GHz GBW, 1.1nV/Hz Differential Amplifier/ADC Driver 88dB SFDR at 100MHz, Input Range Includes Ground 52mA Supply Current 3mm x 2mm QFN Package LTC6412 800MHz, 31dB Range, Analog-Controlled Variable Gain Amplifier Continuously Adjustable Gain Control, 35dBm OIP3 at 240MHz, 10dB Noise Figure, 4mm x 4mm QFN-24 LTC6420-20 1.8GHz Dual Low Noise, Low Distortion Differential ADC Drivers for 300MHz IF Fixed Gain 10V/V, 1nV/Hz Total Input Noise, 80mA Supply Current per Amplifier, 3mm x 4mm QFN-20 Receiver Subsystems LTM(R)9002 14-Bit Dual Channel IF/Baseband Receiver Subsystem Integrated High Speed ADC, Passive Filters and Fixed Gain Differential Amplifiers LTM9003 12-Bit Digital Pre-Distortion Receiver ADC Driver, 0.4GHz to 3.8GHz RF Input 21576512fb 32 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC2157-12 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC2157-12 LT 0715 REV B * PRINTED IN USA (c) LINEAR TECHNOLOGY CORPORATION 2011