P6SMB Transient Voltage Suppressors Series MERITEK UL E223045 FEATURES For surface mounted applications in order to optimize board space. Low profile package. Built-in strain relief. Glass passivated junction. Low inductance. Excellent clamping capability. SMB/DO-214AA Repetition Rate (duty cycle): 0.01%. Fast response time: typically less than 1.0ps from 0 volt to VBR for Unidirectional types. Typical IR less than 1A above 10V. High Temperature soldering: 260C/10 seconds at terminals. P MECHANICAL DATA M DO-214AA. Molded plastic over glass passivated junction. Case: JEDEC DO--201 Molded Plastic. Terminal: Solder plated,solderable solderableper perMIL-STD-750, MIL-STD-750,Method Method2026. 2026. Terminals: Axial leads, banddenotes denotescthode cathode except Bidirectional. Polarity: Color and excep B ipolar. Standard Packaging: 12mm tape (EIA STD RS-481). Mounting Position: Any. Weight: 0.003 ounce, 0.093 grams. DEVICES FOR BIPOLAR APPLICATION For Bidirectional use CA suffix for type P6SMB6.8CA through type P6SMB550CA; Electrical characteristics apply in both directions. MAXIMUM RATINGS AND CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. RATING SYMBOL VALUE UNIT Peak Pulse Power Dissipation on 10/1000s waveform. (Note 1, Note 2, Fig. 1) PPPM Minimum 600 Watts Peak Pulse Current on 10/1000s waveform. (Note 1,Fig. 3) IPPM See Table Amps PM(AV) 5.0 Watts IFSM 100 Amps TJ , TSTG -65 to +150 Steady State Power Dissipation at TL =75Lead length .375"(9.5mm). (Note 2, Fig. 5) Peak Forward Surge Current8.3ms Single Half Sine-Wave Superimposed on Rated Load. (JEDEC Method) (Note 3, Fig. 6) Operating junction and Storage Temperature Range. Notes: 1. Non-repetitive current pulse, per Fig. 3 and derated above TA = 25 per Fig. 2. N 2. Mounted on 5.0mm x 5.0mm (0.03mm thick) Copper Pads to each terminal. 2 single half sine-wave, or equivalent square wave, Duty cycle = 4 pulses per minute maximum. 3. 8.3ms . All specifications are subject to change without notice. 1 Rev 7 P6SMB Transient Voltage Suppressors Series MERITEK PACKAGE DIMENSIONS t Cathode Band s D1 D d T1 T L SMB/DO-214AA Millimeters Item Inches Min. Max. Min. Max. L 4.06 4.57 0.160 0.180 D 3.30 3.94 0.130 0.155 D1 1.95 2.20 0.077 0.086 T 5.21 5.59 0.205 0.220 T1 0.76 1.52 0.030 0.060 d - 0.203 - 0.008 s 2.13 2.44 0.084 0.096 t 0.152 0.305 0.006 0.012 SPECIFICATIONS Part Number UNI-POLAR BI-POLAR Maximum Peak Reverse Device Reverse Breakdown Breakdown Test Clamping Pulse Leakage Voltage Marking Stand-Off Voltage Current Voltage @IT @IT Current @VRWM Code Voltage @IPP UNI BI VRWM(V) VBR MIN.(V) VBR MAX.(V) IT(mA) VC(V) IPP(A) IR(A) P6SMB6.8A P6SMB6.8CA 6V8A 6V8C 5.80 6.45 7.14 10 10.5 58.1 1000 P6SMB7.5A P6SMB7.5CA 7V5A 7V5C 6.40 7.13 7.88 10 11.3 54.0 500 P6SMB8.2A P6SMB8.2CA 8V2A 8V2C 7.02 7.79 8.61 10 12.1 50.4 200 P6SMB9.1A P6SMB9.1CA 9V1A 9V1C 7.78 8.65 9.55 1 13.4 45.5 50 P6SMB10A P6SMB10CA 10A 10C 8.55 9.50 10.50 1 14.5 42.1 10 P6SMB11A P6SMB11CA 11A 11C 9.40 10.50 11.60 1 15.6 39.1 5 P6SMB12A P6SMB12CA 12A 12C 10.20 11.40 12.60 1 16.7 36.5 5 P6SMB13A P6SMB13CA 13A 13C 11.10 12.40 13.70 1 18.2 33.5 1 P6SMB15A P6SMB15CA 15A 15C 12.80 14.30 15.80 1 21.2 28.8 1 P6SMB16A P6SMB16CA 16A 16C 13.60 15.20 16.80 1 22.5 27.1 1 P6SMB18A P6SMB18CA 18A 18C 15.30 17.10 18.90 1 25.5 24.2 1 P6SMB20A P6SMB20CA 20A 20C 17.10 19.00 21.00 1 27.7 22.0 1 P6SMB22A P6SMB22CA 22A 22C 18.80 20.90 23.10 1 30.6 19.9 1 P6SMB24A P6SMB24CA 24A 24C 20.50 22.80 25.20 1 33.2 18.4 1 P6SMB27A P6SMB27CA 27A 27C 23.10 25.70 28.40 1 37.5 16.3 1 2 Rev 7 P6SMB Transient Voltage Suppressors Series MERITEK 3DUW 1XPEHU 81,32/$5 %,32/$5 0D[LPXP 3HDN 5HYHUVH 'HYLFH 5HYHUVH %UHDNGRZQ %UHDNGRZQ 7HVW &ODPSLQJ 3XOVH /HDNDJH 9ROWDJH 0DUNLQJ 6WDQG2II 9ROWDJH &XUUHQW 9ROWDJH #,7 #,7 &XUUHQW #95:0 &RGH 9ROWDJH #,33 81, %, 95:0 9 9%5 0,1 9 9%5 0$; 9 ,7 P$ 9& 9 ,33 $ ,5 $ 41.4 14.7 1 P6SMB30A P6SMB30CA 30A 30C 25.60 28.50 31.50 1 P6SMB33A P6SMB33CA 33A 33C 28.20 31.40 34.70 1 45.7 13.3 1 P6SMB36A P6SMB36CA 36A 36C 30.80 34.20 37.80 1 49.9 12.2 1 P6SMB39A P6SMB39CA 39A 39C 33.30 37.10 41.00 1 53.9 11.3 1 P6SMB43A P6SMB43CA 43A 43C 36.80 40.90 45.20 1 59.3 10.3 1 P6SMB47A P6SMB47CA 47A 47C 40.20 44.70 49.40 1 64.8 9.4 1 P6SMB51A P6SMB51CA 51A 51C 43.60 48.50 53.60 1 70.1 8.7 1 P6SMB56A P6SMB56CA 56A 56C 47.80 53.20 58.80 1 77.0 7.9 1 P6SMB62A P6SMB62CA 62A 62C 53.00 58.90 65.10 1 85.0 7.2 1 P6SMB68A P6SMB68CA 68A 68C 58.10 64.60 71.40 1 92.0 6.6 1 P6SMB75A P6SMB75CA 75A 75C 64.10 71.30 78.80 1 103.0 5.9 1 P6SMB82A P6SMB82CA 82A 82C 70.10 77.90 86.10 1 113.0 5.4 1 P6SMB91A P6SMB91CA 91A 91C 77.80 86.50 95.50 1 125.0 4.9 1 P6SMB100A P6SMB100CA 100A 100C 85.50 95.00 105.00 1 137.0 4.5 1 P6SMB110A P6SMB110CA 110A 110C 94.00 105.00 116.00 1 152.0 4.0 1 P6SMB120A P6SMB120CA 120A 120C 102.00 114.00 126.00 1 165.0 3.7 1 P6SMB130A P6SMB130CA 130A 130C 111.00 124.00 137.00 1 179.0 3.4 1 P6SMB150A P6SMB150CA 150A 150C 128.00 143.00 158.00 1 207.0 2.9 1 P6SMB160A P6SMB160CA 160A 160C 136.00 152.00 168.00 1 219.0 2.8 1 P6SMB170A P6SMB170CA 170A 170C 145.00 162.00 179.00 1 234.0 2.6 1 P6SMB180A P6SMB180CA 180A 180C 154.00 171.00 189.00 1 246.0 2.5 1 P6SMB200A P6SMB200CA 200A 200C 171.00 190.00 210.00 1 274.0 2.2 1 P6SMB220A P6SMB220CA 220A 220C 185.00 209.00 231.00 1 328.0 1.9 1 P6SMB250A P6SMB250CA 250A 250C 214.00 237.00 263.00 1 344.0 1.8 1 P6SMB300A P6SMB300CA 300A 300C 256.00 285.00 315.00 1 414.0 1.5 1 P6SMB350A P6SMB350CA 350A 350C 300.00 332.00 368.00 1 482.0 1.3 1 P6SMB400A P6SMB400CA 400A 400C 342.00 380.00 420.00 1 548.0 1.1 1 P6SMB440A P6SMB440CA 440A 440C 376.00 418.00 462.00 1 602.0 1.0 1 P6SMB480A P6SMB480CA 480A 480C 408.00 456.00 504.00 1 658.0 0.9 1 P6SMB510A P6SMB510CA 510A 510C 434.00 485.00 535.00 1 698.0 0.9 1 P6SMB530A P6SMB530CA 530A 530C 477.00 503.50 556.50 1 725.0 0.8 1 P6SMB540A P6SMB540CA 540A 540C 486.00 513.00 567.00 1 740.0 0.8 1 P6SMB550A P6SMB550CA 550A 550C 495.00 522.50 577.50 1 760.0 0.8 1 C Note: For Bidirectional type having VRWM of 10 volts and less,the IR limit doubles. 3 Rev 7 P6SMB Transient Voltage Suppressors Series MERITEK RATING AND CHARACTERISTIC CURVES (TA: 25C UNLESS OTHERWISE SPECIFIED) Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve 100 Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 100 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 75 50 25 0 0.000001 0.00001 0.0001 0.001 0 td-Pulse Width (sec.) 75 100 125 150 175 Figure 4 - Typical Junction Capacitance 10000 150 tr=10sec TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Bi-directional V=0V 1000 Cj (pF) IPPM- Peak Pulse Current, % IRSM 50 TA - Ambient Temperature (C) Figure 3 - Pulse Waveform Half Value IPPM IPPM ( ) Uni-directional V=0V Uni-directional @VR 100 2 Bi-directional @VR 50 0 10/1000sec. Waveform as defined by R.E.A 10 Tj=25C f=1.0MHz Vsig=50mVp-p td 1.0 0 2.0 3.0 1 1.0 4.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) t-Time (ms) Figure 6 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Dissipation Derating Curve 6 120 IFSM - Peak Forward Surge Current (A) PM(AV), Steady State Power Dissipation (W) 25 5 4 3 2 1 0 100 80 60 40 20 0 0 25 50 75 100 125 150 175 1 TA - Ambient Temperature (C) 10 100 Number of Cycles at 60 Hz 4 Rev 7