MULTILAYER CERAMIC ANTENNA FOR BLUETOOTH/WLAN IEEE 802.11b & WLAN IEEE 802.11a (2.45/5.2GHz) (Surface Mounted Ceramic Dual Band Antenna) Product Specification1 (Preliminary) QUICK REFERENCE DATA Dimension 8.7* 8 * 0.9 mm Central Frequency* 2.45 GHz /5.2GHz Bandwidth >100 MHz Gain* 0 dBi max VSWR 2.5 max Polarization Linear Azimuth Omni-directional Impedance 50 Operating Temperature -55~125 oC Termination Ni/Sn (Environmentally-Friendly Leadless) Resistance to soldering heat 260oC, 10 sec. Maximum Power 1W * Actual value will depend on size of customer ground plane Special Environmental Concerns- Green Products Design: The foil making process is using environmentally-friendly aqueous solvent technology. Termination is lead free (Pb free) and packing materials can be re-cycled 1 All the technical data and information contained herein are subject to change without prior notice Print date 01/12/13 HF R&D Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 1 sheet 190-1 A4 APPLICATION 9mm Suggested Layout Ground plane(back side) 2mm Cleanance 6mm Antenna Bluetooth module or other RF Module 6mm Cleanance 50Ohm Transmission Line (by Microstrip Line or Coplanar Waveguide) DIMENSIONAL DATA Figure s1 s1 s1 Dimension s1 s1 s1 C L 8.7 0.25 mm - W 8 0.2 mm - T 0.9 0.2 mm - F 1.25 0.25 mm C L Port S1 Feed Termination 0.5 0.3 mm - 1.25 0.35 mm NC Solder Termination C s1 F s1 T W s1 F s1 HF R&D Print date 01/12/13 Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 2 sheet 190-2 A4 SOLDER LAND PATTERN Figure Remark Dimensions L F L 10 0.10 mm F 1.40 0.10 mm C 0.90 0.10 mm S1 1.40 0.10 mm Feed Pad NC Mount Pad S1 C C Typical Radiation Pattern Polar Plot (Based on Suggested Layout) 0 45 0 -45 90 45 -90 135 225 -45 90 -90 135 225 180 180 E-Plane H-Plane HF R&D Print date 01/12/13 Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 3 sheet 190-3 A4 CUSTOMERIZED TEST BOARD FOR RETURN LOSS Phycomp Dual Band for IEEE802.11a & IEEE802.11b SMA Connector 1 cm 4 inch coaxial cable RG-316 2.5 cm 50 Ohm Transmission Line Solder Joint 1 HF R&D Print date 01/12/13 Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 4 sheet 190-4 A4 RELIABILITY DATA (Reference to IEC Specification) IEC IEC 384-10/ 60068-2 TEST PROCEDURE CECC 32 100 CLAUSE REQUIREMENTS TEST METHOD 4.4 Mounting 4.5 4.6.1 Visual inspection and dimension check Antenna 4.8 Adhesion 4.9 Bond strength of plating on end face The antenna can be mounted on printedcircuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive Any applicable method using x 10 magnification Frequency = 2.45/5.2 GHz; at 20 oC A force of 3 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate Mounted in accordance with CECC 32 100, paragraph 4.4 Conditions: bending 0.5 mm at a rate of 1mm/s, radius jig. 340 mm, 2mm warp on FR4 board of 90 mm length HF R&D Print date 01/12/13 No visible damage In accordance with specification (chip off 4mm) Standard test board in page 4 No visible damage No visible damage No visible damage Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 5 sheet 190-5 A4 IEC IEC 384-10/ CECC 32 100 CLAUSE 60068-2 TEST METHOD 4.10 20(Tb) TEST Resistance to soldering heat PROCEDURE REQUIREMENTS 260 5 C for 10 0.5 s The terminations shall be well tinned in a static solder bath after recovery and Central Freq. Change 6% Resistance to leaching 4.11 20(Ta) Solderability 4.12 4(Na) Rapid change of temperature 4.14 3(Ca) Damp heat 260 5 C for 30 1 s in a static solder bath Using visual enlargement of x 10, dissolution of the termination shall not exceed 10% Zero hour test, and test The termination must after storage (20 to 24 be well tinned, at months) in original least 75% is well atmosphere; un-mounted tinned at termination chips completely immersed for 2 0.5 s in 235 5C. No visible damage -55 C (30 minutes) to Central Freq. Change +125 C (30 minutes); 6% 100 cycles 500 12 hours at 60 C; No visible damage 2 hours recovery 90 to 95 % RH Central Freq. Change 6% 4.15 500 12 hours at 125 C; Endurance No visible damage 2 hours recovery Central Freq. Change 6% HF R&D Print date 01/12/13 Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 6 sheet 190-6 A4 ORDERING INFORMATION: Method I- by 12NC Ordering Code The antennas may be ordered by using the 12 NC ordering code. These code numbers can be determined by the following rules: 4313 1 17 00 252 F C MS T A F. Family Code 43 = Antenna C. Packing Type Code 13 = 180 mm/ 7" blister (1000pcs) M. Materials Code 1 = High Frequency Material S. Size Code 17 = 8.7 * 8 * 0.9 mm T. Tolerance 00 = 100 M Hz Band Width A. Working Frequency 252 = 2.45/5.2 GHz Dual Band Example: 12NC 4313 117 00252 Product description: Antenna (43) by 180 mm blister (11) of High Frequency Material (1), Size 8.7*8*0.9 mm (17); Tolerance (00) of 100 MHz (VSWR<2.5) Working Frequency (252) = 2.45/5.2G Hz Dual Band ORDERING INFORMATION: Method II- by Clear Text Code The antennas may be ordered by using the 16-digit clear text ordering code. These code numbers can be determined by the following rules: AN2520000708081K (Clear Text Code Example) AN Product AN= Antenna 2520 Central Freq. 2520=2.45GHz + 5.2GHz HF R&D 00 Bandwidth 00= >100MHz 07 Material 07=K7 0808 Size 0808=8.7*8* 0.9 mm Print date 01/12/13 1 Quantities 1 = 1K 4 = 4K K Packing K=7" plastic Preliminary internal use only Sep. 13, 01 Multilayer Ceramic Antenna for IEEE802.11a & IEEE802.11b Grant Lin/Cliff spec.doc 2001-9-13 Phycomp Taiwan Ltd. 4313 117 00252 Page 7 sheet 190-7 A4