PRELIMINARY DATA SHEET MICRONAS INTERMETALL CAP 3001 A Car Audio Processor Hardware MICRONAS Edition April 4, 1996 6251-365-1DS CAP 3001 A Contents Page Section Title 4 4 1. 1.1. Introduction Features 4 4 4 4 4 6 7 7 8 8 8 8 8 8 9 9 11 12 12 12 12 12 13 15 15 17 2. 2.1. 2.1.1. 2.1.2. 2.1.3. 2.1.4. 2.1.5. 2.1.6. 2.1.7. 2.1.8. 2.1.9. 2.1.10. 2.1.11. 2.1.12. 2.1.13. 2.1.13.1. 2.1.13.2. 2.1.14. 2.1.15. 2.1.16. 2.1.17. 2.1.18. 2.1.19. 2.1.20. 2.1.21. 2.1.22. Functional Description Architecture DSP Block Digital Part Analog Part Operating Modes Analog Input Systems Buffers ABUF Stereo Mixer AMIX AM Mixer AMMIX Multiplexers AMUX A/D-Converters ADC Digital Signal Processing Block Digital Filter Sections Digital Mixing Sections Pilot Demodulator PILMX ARI Mixer ARIMIX FM Noise Canceller (ASU) Analog Output Systems D/A Converters DAC Lowpass-Filters ALPF Volume Control AVOL CAP 3001 A - Programmable Digital Audio Interface (PDAI) The IM-Bus Interface of the CAP 3001 A Description of the IM-Bus Clock Generation 18 18 18 21 23 24 24 24 26 27 3. 3.1. 3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5. 3.1.6. 3.1.7. 3.1.8. Specifications Outline Dimensions Pin Connections and Short Descriptions Pin Descriptions Pin Configuration Electrical Characteristics Absolute Maximum Ratings Recommended Operating Conditions Recommended Crystal Characteristics Characteristics 2 MICRONAS INTERMETALL CAP 3001 A Contents, continued Page Section Title 31 4. Starting the Processor 31 5. Synthesizer 32 6. Application Notes 33 7. Typical Application Circuit 34 8. Index 36 9. Data Sheet History MICRONAS INTERMETALL 3 CAP 3001 A Car Audio Processor 2. Functional Description 1. Introduction 2.1. Architecture The CAP 3001 A Car Audio Processor presents the onechip solution for a highly integrated car radio concept. It is housed in a 68-pin Plastic Leaded Chip Carrier Package. The architecture of the CAP 3001 A processor comprises three main function blocks: 2.1.1. DSP Block The CAP 3001 A Car Audio Processor is a new CMOS processor to be used for car radio systems. The application consists essentially of the following components: - conventional FM tuner, FM-IF stage and FM demodulation The DSP block consists of a "General Purpose16-Bit Digital Signal Processor" which handles 24 million instructions per second. The data word length is 16 bits and the hardware multiplier operates with an initial word length of 1610 with a 20-bit result. The memory covers 2561625610 bit RAM and 2 k instruction ROM. - conventional AM tuner and IF stage 2.1.2. Digital Part - Car Audio Processor CAP 3001 A A main portion consists of hardwired digital filters, such as decimation filters for the A/D converters and interpolation filters for D/A converters. The modulators for ARI/ RDS and pilot tone, as well as the complete circuitry for the ignition noise canceller are realized digitally. The logical conclusion for a higher integration is the incorporation of the synthesizer for AM and FM tuning into this hardware block. Naturally the customary serial interfaces for digital audio signals are also included. - microcontroller - analog audio sources - digital audio source 1.1. Features1) - stereo decoder - baseband audio processing 2.1.3. Analog Part - ignition noise canceller - synthesizer with fast tuning - AM tuning for 450 to 460 kHz or 10.7 MHz IF - AM IF processing (450 to 460 kHz) - AM stereo (C-QUAM) demodulation - ARI/RDS processing - PDAI Programmable Digital Audio Interface - A/D converter - D/A converter with eightfold oversampling filter. 4 In the analog part various input switches, A/D converters and D/A converters are combined. Five A/D converters handle the conversion of analog signals into digital signals. Two of these are specially designed for high quality, one in particular for the conversion of an independent signal path for ARI/RDS signals and the remaining two to be used for the evaluation of analog signals of a lower quality standard (information on field strength and information from potentiometers). Two D/A converters, each equipped with an eightfold oversampling filter, generate analog output signals. These two outputs can be split up and distributed via four independently adjustable volume control switches into four output stages. MICRONAS INTERMETALL Fig. 2-1: CAP 3001 A block diagram MICRONAS INTERMETALL SCLKI SDIN1 L+R MPX Decoder A/D 0 AML or AMIF AMIF DSP Core 1) FM-Noise Reduction A/D 1 Input Select Stereo Matrix Tone Control Pilot Filter Loudness Deemphasis Noise Reduction Volume Balance L+R FM-Noise Detection TAPER TAPEL Pilot Mixer AUXR AUXL ARI/RDS Mixer A/D 2 DSP Input Buffer POT1/MPX1 POT2 POT3 POT4 POT5/AVC ARI Decoding (SK + DK) RDS Demodulation CQUAM Demodulation Input Select LF D/A Analog Volume LR Over- Analog Volume RF Analog Volume RR sampled DSP Output Buffer sampled A/D3 Soft Blend Beep Generator D/A Stereo Detection Stereo PLL Filter Blank Search A/D 4 AMLEVEL 1) Synthesizer Listed features depending on software version Auxiliary Digital Inputs Auxiliary Digital Outputs IM-Bus/I 2C Interface Clock QX1 FMIN AMIN 5 AMTUNOUT FM TUNOUT TI1 TI2 TI3 TO1 TO2 TO3 IMDATA IMIDENT QX2/ECLK IMCLOCK CLKOUT CAP 3001 A Input Select Analog Volume Over- Multipath Detection FM/AM-Level Detection High Blend FMLEVEL MPLEVEL WSO L-R AMR AMMixer SDIN2 Interface ERR L-R SDOUT Digital Audio WSI MPX0 SCLKO Programmable CAP 3001 A 3) XDS-mode 2.1.4. Operating Modes The CAP 3001 A possesses 4 main operating modes: 1) MPX-mode In this mode, the CAP 3001 A receives the multiplex signal of an FM transmission, containing sum and difference channel, the pilot tone and the signals needed for travel information (ARI, RDS). The FM-demodulation has to take place inside the conventional tuner. The mixing of the difference band is done by an analog mixer in front of the A/D-converters in order to achieve the necessary quality for FM stereo. The ARI and RDS signals and the pilot tone are extracted digitally. 2) AF-mode In this mode the CAP 3001 A works transparently; the incoming signals are only A/D-converted and then transmitted to the DSP core. FM Tuner FM IF In this mode there is an external digital source (XDS, e.g. a CD player) which sends its digital data to the CAP 3001 A for further processing and for the reconverting to analog signals. The CAP 3001 A can be adapted to the sampling rate prescribed by the external digital source; in addition the input systems of the CAP 3001 A remain active in order to monitor the traffic information (ARI/RDS). 4) AM-IF mode In this mode, the CAP 3001 A receives input signals in the AM-IF range (i.e. 450 to 460 kHz). By a special analog mixer in front of the A/D conversion, the AM signal is mixed down to a frequency of 19 kHz. AM mono and stereo (C-QUAM) are demodulated in the DSP software. MPX LF FMLEVEL LR FMTUNOUT FMOSCIN CAP 3001 A AMOSCIN RF AMTUNOUT AM Tuner & IF RR AMIF Controller Fig. 2-2: CAP 3001 A system overview 6 MICRONAS INTERMETALL CAP 3001 A After buffering (ABUF) and switching (AMUX) in the AFmode the signals are converted into digital form by 2 A/D converters (ADCs). Their output is 1 bit at a rate of 8.208 MHz; in each of the two channels in the CAP 3001 A there is a cascade of 3 lowpass filters (LPF02, LPF23 and LPF34), which suppresses the high-frequency noise produced by the ADCs. The outputs of the filters LPF34 are 16 bits wide and are sampled with 38 kHz; these samples are transmitted via the input buffer to the DSP core. After processing in the DSP, the samples are interpolated to the eightfold sampling rate and converted into analog shape by 2 D/A converters (DACs), filtered (ALPF) and optionally attenuated (AVOL) to feed the power amplifiers which produce the signals for four loudspeakers. It is assumed that the process of stereo multiplexing used in radio broadcasting is known. The main FM-modulator can be modulated by the sum signal of left and right channel (in baseband), a pilot tone, the difference channel (AM-modulated, suppressed carrier), an optional ARI signal (AM-modulated, unsuppressed carrier) and optionally up to 3 SCA signals (FM-modulated). The composite signal is the so-called MPX signal. So a variety of signals ride "piggy-back" on the main carrier, which was originally assigned only for monophonic transmission. In the CAP 3001 A, the SCA signals are regarded as disturbing signals while the others are regarded as useful. 2.1.5. Analog Input Systems Fig. 2-3 shows all analog inputs and functions of the switches S0 to S3. 420 to 430 kHz 38 kHz MPX0 AML TAPEL 0 1 1 0 S4 By means of digital mixers the pilot tone and the ARI signal are mixed down to zero intermediate frequency in quadrature representation, where their information is sampled and sent to the DSP core. The demodulation of the ARI signal is done by the DSP software. The bandwidth of this ARI channel is sufficient to allow demodulation of an RDS (Radio Data System) signal by DSP software as well. Beside these main blocks, there are other systems. The analog field strength information FS delivered by AM and FM tuners is A/D-converted; after lowpass-filtering (LPF06) the samples are sent to the DSP core, where the information could be used to control some parameters of the entire system. Other input signals, such as signals from an external microphone and from external potentiometers are selected by an analog multiplexer, A/D-converted, lowpass-filtered and sent to the DSP or to the controller via the IM-bus interface (IMIF). The IM-bus interface is also able to receive data from the external microcontroller and to control the systems on the CAP 3001 A. MICRONAS INTERMETALL S0 AUXL 3 0 AMR 1 TAPER 2 S0 AUXR Main 2 3 0 1 POT1/ MPX1 ARI/RDS 0 POT3 2 POT4 3 S3 4 Pot 5 0 FMLEVEL MPLEVEL S2 1 POT2 POT5/ AVC In the MPX-mode there is an analog mixer AMIX in front of the ADCs. It mixes the difference band down to baseband. The sum channel and the difference channel are then treated like the other baseband signals. Digital quadrature mixers ARIMX and PILMX extract the ARIinformation and the information of the pilot signal, respectively. Main 1 2 1 AMLEVEL 2 S1 Level Fig. 2-3: Analog input systems 2.1.6. Buffers ABUF The analog input buffers have to adjust the individual desired input levels in order to cover the entire volume range of the A/D-converters. The inputs can be divided into two groups: those which have to be connected via external capacitors, and those that are DC-coupled. One of these inputs, the POT5/ AVC-input, uses the same pin, but is DC-coupled if used as POT5, and AC-coupled if used as AVC. Note: Input pins POT2 to POT5 are switchable to digital outputs via the IM-bus interface. This feature is made possible by open drain transistors and external pull-up resistors down to 1 k. 7 CAP 3001 A 2.1.9. Multiplexers AMUX 2.1.7. Stereo Mixer AMIX This analog demodulator mixes the incoming multiplex signal with the PLL-synchronized 38 kHz subcarrier in order to get the difference channel in baseband. The phase of the mixer signal is locked to the phase of the digital pilot demodulator; the phase shift between the two signals has to be compensated by the signal processor's Stereo PLL software. The realized modulator consists of an analog multiplexer switching among the original input signal, the inverted input signal and zero input. The analog multiplexers allow the selection of one of the input signals for each signal path. 2.1.10. A/D-Converters ADC The A/D-converters are realized as pulse density modulators (PDMs) running at a clock frequency of f_s0+8.208 MHz. The ADC0, ADC1 and the ADC2 are high quality double-loop PDMs with one external capacitor whereas ADC3 and ADC4 are low quality PDMs without any external capacitor. 2.1.11. Digital Signal Processing Block 2.1.12. Digital Filter Sections m(t) T_0 1 0 *1 T_0 12 T_0+1/f_0+1 T_0/12+1/(12f_0)+1/4s Fig. 2-4: Difference channel mixing signal The desired fundamental 38 kHz component includes an additional factor of 1.10266 which has to be taken into account in the dematrix-software of the signal processor. 2.1.8. AM Mixer AMMIX This analog modulator mixes the incoming AM-IF signal down to approximately 19 kHz. Just like the AMIX stereo mixer it uses an amplitude discrete signal instead of a sinusoidal signal. The realized modulator consists of an analog multiplexer switching among the original input signal and the inverted input signal. The mixing frequency of this mixer is typically between 430 and 440 kHz and can be selected in approximately 2 kHz steps in order to choose the desired AM IF frequency. 8 After analog to digital conversion, the input signals are filtered by means of digital filters in order to decimate the high frequency PDM signals to an appropriate sampling rate. The second purpose of these filters is to suppress unwanted out-of-band signals and to shape the input signals to the desired response. After being processed in the DSP section, the digital samples are interpolated to a higher rate before being converted to the analog domain. The individual filter blocks can be seen in Fig. 2-5 and 2-6. Fig. 2-5 shows filter sections for the A/D side whereas in Fig. 2-6, filter blocks for the interpolation process on the D/A side can be seen. In the text of the CAP 3001 A data sheet, the filter blocks are referred to with the names indicated in the schematics. Most of the filters are designed as multirate FIR blocks. Fig. 2-7 shows the overall (A/D to D/A) passband characteristics of the main channels in TAPE or AUX mode. The shown 3 dB bandwidth is more than 18 kHz. Fig. 2-8 shows the same for the MPX case. An additional pilot notch filter (19 kHz) suppresses higher frequencies. In case of a locked stereo PLL, the suppression is ideal. Fig. 2-9 depicts the characteristics of the ARI/RDS bandpass. The near-by difference channel is attenuated sufficiently in order to minimize disturbing effects in the weak ARI/RDS signal. An additional lowpass with roll-off characteristics is done in the DSP software. In order to suppress out-of-band signals, the CAP 3001 A is equipped with digital interpolation filters. These filters attenuate alias frequencies of up to eight times the sampling frequency by at least 50 dB. The interpolation block consists of three cascaded linear phase FIR filters. A simple sample and hold filter serves for the interpolation to the operating rate of the D/A converter. The overall interpolation rate is therefore 32. See Fig. 2-10 for the passband characteristics of the interpolation filter (plotted for 44.1 kHz sampling rate) and Fig. 2-11 for the stopband characteristics. MICRONAS INTERMETALL CAP 3001 A 2.1.13. Digital Mixing Systems 2.1.13.1. Pilot Demodulator PILMX The entire system is synchronized with the pilot tone of the FM-stereo channel. In the pilot-demodulator 2 mixers working in quadrature are used. The quadrature mixASU HIGH PASS er is the phase detector of the PLL; the other parts of the PLL (loop filter and VCO) are realized in the DSP. The inphase mixer outputs information concerning the level of the pilot tone to the DSP to allow a decision "FM-stereo" or "FM-mono". The time relation between the mixer sequences of stereo-demodulator and pilot-demodulators is fixed. ASU DETECT AMMIX Main 1 A D LPF 02 36 PILOT NOTCH ASU LPF 23 3 LPF 34 2 LPF 34 2 AMMIX Main 2 A D LPF 02 36 PILOT NOTCH ASU LPF 23 3 LPF 23 A ARI/ RDS D LPF 01 POT A D A D LPF 35 8 PILMIX LPF 35 8 3 DSP 18 LPF 12 Level PILMIX LPF 06 540 LPF 05 864 ARI MIX LPF 24 6 LPF 45 4 ARI MIX LPF 24 6 LPF 45 4 2 Fig. 2-5: Digital signal processing blocks, input side 2 INT 12 4 INT 12 4 INT 28 4 3 NOISE SHAPING D 4 3 NOISE SHAPING D A DSP 2 INT 28 A Fig. 2-6: Digital signal processing blocks, output side MICRONAS INTERMETALL 9 CAP 3001 A dB 3 gain 0 3 0 2 4 6 8 10 12 14 16 18 19 kHz f Fig. 2-7: Overall response TAPE/AUX channel dB 3 gain 0 3 0 2 4 6 8 10 12 14 16 18 19 kHz f Fig. 2-8: Overall MPX response sum channel dB 0 gain 50 100 0 50 100 kHz f Fig. 2-9: ARI/RDS bandpass characteristic 10 MICRONAS INTERMETALL CAP 3001 A dB 3 gain 0 3 0.0 5.0 10.0 15.0 f 20.0 22.05 kHz Fig. 2-10: Digital interpolation filter, passband characteristic dB 0 gain 50 80 0.0 50 100 150 200 250 300 350 kHz f Fig. 2-11: Digital interpolation filter, attenuation 2.1.13.2. ARI Mixer ARIMX The ARI-information in the range of 57 kHz is mixed down to a zero intermediate frequency by the two ARI mixers, whose mixer signals are again in quadrature. The reason for using two paths is that the demodulation is asynchronous in general; in the DSP there should be an operation which performs the square root of the sum of the squares of the two input signals. The quality requirements of the square rooting should not be very high. Because of the phase lock of pilot tone and ARI carrier in the FM-stereo-mode, a synchronous demodulation seems to be possible; in this case the demodu- MICRONAS INTERMETALL lated ARI signal would be identical with the signal of the inphase path. The chosen structure has another potential advantage, for processing the radio data system (RDS) in Europe. This signal is a part of the MPX-signal; its subcarrier frequency is the same as that of the ARI-signal but it is recommended that the two subcarriers are in quadrature. So the two paths of the ARI demodulation subsystem make the information of the ARI-signal and of the RDSsignal available to the DSP, where both can be demodulated if desired. 11 CAP 3001 A 2.1.14. FM Noise Canceller (ASU) 2.1.17. Lowpass-Filters ALPF The FM Noise Canceller removes peak noise from the audio signal. No external circuitry is required. All filters, delays and the control section are implemented digitally. The function is split into two sections: The analog lowpass-filters behind the DACs eliminate the high-frequent noise in order to avoid any distortions in the AM frequency range. 2.1.18. Volume Control AVOL - The noise detection searches for energy in the nonaudio range by means of a highpass filter. The output of this filter is compared with a DSP-controlled threshold. If this threshold is exceeded the interpolation unit is triggered. The 19 kHz pilot tone is removed before the audio signal enters the detection highpass. Programmable delay adjustment makes sure of the correct timing between peak detection and peak interpolation. - The interpolation circuit substitutes a peak-corrupted sample by the mean value of the non-corrupted adjacent samples. Once a trigger comes from the detection circuit, a programmable number (0 to 15) of successive samples is interpolated. All functions work on a 228 kHz sampling rate. At this rate the peaks are still small enough (not widened by the final decimation filters) to be removed effectively. 2.1.15. Analog Output Systems 2.1.16. D/A-Converters DAC The analog volume control together with the digital volume control implemented in the digital signal processor's software provide a large volume control range. The analog volume control itself covers a range of 45 dB in 1.5 dB steps and includes an additional mute position. A sensible splitting of the total gain v_tot between the digital gain v_dig and the analog gain v_anlg is: v_tot v_anlg v_dig v_totw0 dB 0 dB v_tot *45 dBtv_tott0 dB v_tot 0 dB v_tott*45 dB *45 dB v_tot)45 dB All control bits for the hardware section are first addressed to the DSP core program. In case of hardware read-registers the bits are transmitted to the DSP core, stored in the DSP RAM and so they are available for the controller via the DSP's IM-bus interface. The D/A-converters used are of the oversampling type. The samples to be converted at their sampling rate f_s are first interpolated to 8 x the sampling rate and then oversampled to a higher rate f_NS where noise shaping is performed. The output of the noise shaper is then converted using a highly linear D/A-converter. Its noise power density increases with increasing frequency, the residual noise in the baseband is very low. Within this application the DAC has to be adapted to the different modes. The digital sources (e.g. CD-player) must supply the proper clock rate in order to drive the DAC with a stable clock rate locked to the sampling rate. The clock is derived from the clock line SCLK of the PDAI bus. 12 MICRONAS INTERMETALL CAP 3001 A 2.1.19. CAP 3001 A - Programmable Digital Audio Interface (PDAI) The PDAI is the digital audio interface between the CAP 3001 A and external digital sources such as CD/DAT player or additional external processors. It offers a large variety of modes and should therefore cover most of the digital audio standards (I2S-compatible formats). Fig. 2-12 shows a standard application with an external digital source and a second CAP 3001 A. The interface is split into the input section and the output section: Input Section: - SCLKI - SDIN1 - WSI - ERR serial clock input serial data input 1 word select input error line input Output Section: - SCLKO - SDOUT - SDIN2 - WSO serial clock output serial data output serial data input 2 word select output Fig. 2-13 shows the timing of the signals and the programmable features. The programming is done by writing the correct bit patterns into the DSP output buffer. This must be handled by the DSP software. CD-PLAYER SCLKI WSI SDIN1 ERR analog input SCLKO CAP 3001 A SDOUT SDIN2 WSO CAP 3001 A or ext. Proc. CLKOUT analog output Fig. 2-12: System Configuration MICRONAS INTERMETALL 13 CAP 3001 A Tbck 16, 24, 32 x Tbck SCLK_IN/OUT polarity programmable WS_IN/OUT 1 Tbck: programmable SDATA MSB LSB LSB MSB ERR MSB/LSB first programmable 0, 8, 16 x Tbck: programmable delay Fig. 2-13: Timing of the signals Tbck+1/Fbck Fbck+32@Fsaudio or Fbck+48@Fsaudio or Fbck+64@Fsaudio The modes are: In all modes: - 16-bit wordframe in this case the programmable delay is set to zero; MSB or LSB-first can be selected; one bit delay between active slope of WSI/O and first wordframe bit is programmable; the polarity of WSI/O can be programmed ; in the 24 and 32-bit wordframes the open data bit locations are MSB or LSB extended (depends on left or right adjustment). - 24-bit wordframe in this case the programmable delay is set either to 0 or to 8 Tbck; this allows left or right adjusted handling of the 16 data bits - 32-bit wordframe in this case the programmable delay is set either to 0 or to 16 Tbck; this allows left or right adjusted handling of the 16 data bits. 14 Input format and output format can be programmed separately. The restrictions are: A 24-bit wordframe can only be sent if a 24-bit wordframe is also received. In the analog input mode, the 24-bit wordframe output is not allowed. MICRONAS INTERMETALL CAP 3001 A 2.1.20. The IM Bus Interface of the CAP 3001 A III III III III III III III III LSB IABF 10 shift 2.1.21. Description of the IM Bus IM Bus IMIDENT Control LSB 16 IMDATA MSB IDBF shift MSB IMCLK Data Bus Fig. 2-14: IM-bus interface The buffer part consists of a unidirectional address buffer IABF with a word length of 10 bit and the bidirectional data buffer IDBF with a word length of 16 bit. It is only possible to write to the address buffer from the peripheral equipment. By means of the IM-bus interface it is possible, for example, to alter the filter coefficients of the CAP 3001 A. For this purpose the microcomputer writes an address and a data word to the appropriate buffers IABF and IDBF. The 10-bit address contains an address part of 8 bits (bit 9 to bit 2), a read/write bit (bit 0) and an additional bit (bit 1) which may be used, for example, for selecting one of the two address counter banks (Fig. 2-15). Bits 0 and 1 have the following effect: ABNK0 selects address counter bank 1 ABNK1 selects address counter bank 2 R/W0 selects Write, microcomputer wants to write R/W1 selects Read, microcomputer wants to read MSB buffer size, the unused bits are set to zero in IDBF but remain undefined in IABF. For the output: the first bit output is always the LSB of the IDBF. Address LSB ABNK R/W Fig. 2-15: Address format The following convention is applicable to the data transfer: The last bit written always becomes the MSB of IABF or IDBF. If fewer bits are transferred than the respective MICRONAS INTERMETALL The IM-bus consists of three lines for the signals Ident (IMIDENT), Clock (IMCLK) and Data (IMDATA). The clock frequency range is 50 Hz to 1 MHz. Ident and clock are unidirectional from the controller to the slave ICs, Data is bidirectional. Bidirectionality is achieved by using open-drain outputs with on-resistances of 150 Ohm maximum. The 2.5 k pull-up resistor common to all outputs is incorporated in the controller. The timing of a complete IM-bus transaction is shown in Fig. 2-16. In the non-operative state the signals of all three bus lines are High. To start a transaction, the controller sets the ID signal to Low level, indicating an address transmission, sets the CL signal to Low level and switches the first bit on the Data line. Then 10 address bits are transmitted, beginning with the LSB. Data takeover in the slave ICs occurs at the positive edge of the clock signal. At the end of the address byte the ID signal goes High, initiating the address comparison in the slave circuits. In the addressed slave the IM-bus interface switches over to Data read or write, because these functions are correlated to the address. In the case of a read operation, a fixed wait period has to be observed. This period is defined by the IM-bus handler in the DSP software. For practical reasons this part of the program does not run at the full sampling rate. It is recommended to place the IM-bus handler in a "low speed" time slice in order to save processing power. For a write operation this wait period does not have to be observed, but please note that the maximum rate of IMbus transmissions is normally limited by the DSP software. Also controlled by the address the controller now transmits sixteen clock pulses, and accordingly two Bytes of data are written into the addressed IC or read out from it, beginning with the LSB. The completion of the bus transaction is signalled by a short Low state pulse of the ID signal. This initiates the storing of the transferred data. A bus transaction may be interrupted for up to 10 ms. 15 CAP 3001 A H Ident L H 26 Clock 1 2 3 4 5 6 7 8 9 10 11 12 13 L H Data Address LSB MSB LSBData MSB L B A Section A Section B C Section C tIM10 H Ident L tIM1 tIM3 tIM4 tIM6 tIM5 tIM2 H Clock L tIM7 H Data tIM8 Address LSB tIM9 Address MSB Data MSB L Fig. 2-16: IM Bus waveforms 16 MICRONAS INTERMETALL CAP 3001 A 2.1.22. Clock Generation The CAP 3001 A processor has an integrated clock oscillator which is crystal-controlled and oscillates with the frequency fECLK16.416 MHz. All components of the oscillator are integrated except for the quartz crystal. This is connected to the QX1 and QX2 oscillator pins. The crystal input QX2/ECLK can be used to supply the CAP 3001 A externally with the required clock. In this case no crystal is needed. Following the clock oscillator is a frequency multiplier with a factor of 3. The output of the frequency multiplier delivers the fICLK internal clock frequency, by which the DSP Core is clocked. There is the possibility of pulling the fECLK oscillator frequency in a range of 350 ppm, depending on the application and the used crystal. This makes it possible to synchronize the CAP 3001 A to the incoming pilot tone signal in the case of MPX reception. Table 2-1: Oscillator characteristics DCO Content Frequency 011111111B 000000000B 100000000B fECLKmin fECLK fECLKmax 9 DCO Clock Control Register Clock Oscillator 39 39 38 38 3 4 100 nF GNDD external option fICLK 2 ECLK fECLK Frequency Multiplier 1 1 nF Clock Pulse Shaper 62 and CLKOUT Frequency Divider Fig. 2-17: Clock generator connections MICRONAS INTERMETALL 17 CAP 3001 A 3. Specifications 3.1. Outline Dimensions 2.4 1+0.2 x 45 1.27 0.1 60 10 2.4 61 2 2 24.2 0.1 25 +0.25 0.711 9 15 0.2 9 44 26 27 43 25 +0.25 16 x 1.27 0.1 = 20.32 0.1 1 0.457 9 16 x 1.27 0.1 = 20.32 0.1 1.27 0.1 1.2 x 45 1.9 1.5 4.05 4.75 0.15 24.2 0.1 0.1 70043/2 Fig. 3-1: 68-Pin Plastic Leaded Chip Carrier Package (PLCC68) Weight approximately 4.8 g Dimensions in mm 3.1.1. Pin Connections and Short Descriptions S.T.B. = shorted to BAGNDI if not used DVSS = if not used, connect to DVSS X = obligatory; connect as described in circuit diagram AHVSS = connect to AHVSS NC = not connected; leave vacant LV = if not used, leave vacant Pin No. Connection PLCC 68-pin (if not used) 18 Pin Name Type Short Description 1 GNDA FMLEVEL IN FM fieldstrength input 2 GNDA POT5/AVC IN/OUT DC voltage input 3 GNDA POT4 IN/OUT DC voltage input 4 GNDA POT3 IN/OUT DC voltage input 5 GNDA POT2 IN/OUT DC voltage input 6 GNDA POT1/MPX1 IN/OUT DC voltage input 7 AGNDC MPX0 IN FM MPX signal input 8 AGNDC AML IN AM left baseband input 9 BAGNDC AMR IN AM right baseband input 10 BAGNDC AUXR IN Auxiliary audio input right 11 BAGNDC AUXL IN Auxiliary audio input left 12 BAGNDC TAPER IN Analog tape input right MICRONAS INTERMETALL CAP 3001 A Pin Connections and Short Descriptions, continued Pin No. Connection PLCC 68-pin (if not used) Pin Name Type Short Description 13 BAGNDC TAPEL IN Analog Tape input left 14 BAGNDC PDMC3 EXT PDM capacitor connection 15 BAGNDC PDMC2 EXT PDM capacitor connection 16 BAGNDC PDMC1 EXT PDM capacitor connection 17 LV BAGNDC OUT Buffered internal ground 18 X AGNDC EXT Internal analog ground 19 X VREF1 IN Analog ground reference 20 X GNDA SUPPLY Analog ground 21 X VSUPA SUPPLY Analog supply voltage 22 LV LF OUT Analog output left front 23 LV LR OUT Analog output left rear 24 LV RR OUT Analog output right rear 25 LV RF OUT Analog output right front 26 X VREF2 IN Analog ground reference synthesizer 27 LV FMTUNOUT OUT FM tuning voltage output 28 LV TUNFB IN Tuning voltage feedback input 29 LV AMTUNOUT OUT AM tuning voltage output 30 VREF2 VSUP2 SUPPLY Analog supply voltage synthesizer 31 VREF2 VSUP1 SUPPLY Analog supply voltage synthesizer 32 LV AMOSCREF EXT AMOSC capacitor connection 33 LV AMOSCIN IN AM oscillator signal input 34 LV FMOSCREF EXT FMOSC capacitor connection 35 LV FMOSCIN IN FM oscillator signal input 36 X GNDS1 SUPPLY Analog ground synthesizer 37 GNDD TESTEN IN Test Mode Enable 38 X QX1 IN Crystal 39 X QX2/ECLK IN Crystal/External clock input 40 X RESET IN Reset input 41 X IMDATA IN/OUT IM-bus/I2C data input/output 42 X IMCLK IN IM-bus/I2C clock input MICRONAS INTERMETALL 19 CAP 3001 A Pin Connections and Short Descriptions, continued Pin No. Connection PLCC 68-pin (if not used) Type Short Description 43 X IMIDENT IN IM-bus ident input 44 GNDD TEOSC IN Test purpose 45 LV REFCLK IN Synthesizer Ref. Frequency input 46 LV1) TI1 IN Static digital input 1 47 LV1) TI2 IN Static digital input 2 48 LV1) TI3 IN Static digital input 3 49 LV SCLKO OUT Serial clock output 50 LV WSO OUT Serial word select output 51 LV SDOUT OUT Serial data output 52 LV SDIN2 IN Serial data input 2 53 LV ERR IN Serial error input 54 LV SCLKI IN Serial clock input 55 LV WSI IN Serial word select input 56 LV SDIN1 IN Serial data input 1 57 LV TO1 OUT Digital output 1 58 LV TO2 OUT Digital output 2 59 LV TO3 OUT Digital output 3 60 X GNDD SUPPLY Digital ground 61 X VSUPD SUPPLY Digital supply voltage 62 LV CLKOUT OUT Clock output 63 GNDD TP3 IN Test purpose 64 LV TP2 OUT Test purpose 65 LV TP4 OUT Test purpose 66 GNDD TP1 IN Test purpose 67 GNDA AMLEVEL IN AM fieldstrength input 68 GNDA MPLEVEL IN Multipath signal input 1) Depending 20 Pin Name on software version. MICRONAS INTERMETALL CAP 3001 A 3.1.2. Pin Descriptions Pin1 - FMLEVEL Input for the FM field strength information. Pins 2 to 6 - POT5/AVC, POT4, POT3, POT2, POT1/MPX1 Inputs for a DC-control voltage (0V to VSUP). These pins can also be used as digital outputs with an external pullup resistor; the function and selection is controlled via IM/I2C-bus. POT1/MPX1 also serves as a second MPX input for ARI/ RDS. POT5/AVC also serves as a highly sensitive microphone input. Pin 7 - MPX0 Input for the MPX signal in case of FM reception. Pin 8 - AML Input for left channel baseband audio; or for AM IF (450 to 460 kHz). Pin 9 - AMR Input for right channel baseband audio. Pin 21 - VSUPA Analog supply voltage; power for the analog circuitry of the CAP 3001 A is supplied via this pin. Pin 22 - LF Left front speaker output. Pin 23 - LR Left rear speaker output. Pin 24 - RR Right rear speaker output. Pin 25 - RF Right front speaker output. Pin 26 - VREF2 This pin serves as ground connection for the synthesizer bias circuits and must be connected separately to the ground point of the tuner. Pin 27 - FMTUNOUT Tuning voltage for the FM oscillator. Pin 28 - TUNFB Feedback input for tuning voltage amplifier. Pin 10 - AUXR Input for additional audio sources, right channel. Pin 29 - AMTUNOUT Tuning voltage for the AM oscillator. Pin 11 - AUXL Input for additional audio sources, left channel. Pin 30 - VSUP2 Synthesizer supply voltage 2; power is supplied via this pin for the synthesizer output circuitry of the CAP 3001 A. Pin 12 - TAPER Input for right tape channel. Pin 13 - TAPEL Input for left tape channel. Pins 14 to 16 - PDMC3, PDMC2, PDMC1 Capacitor pins for the feedback loop of the high quality pulse-density modulators. Pin 17 - BAGNDC Buffered internal ground. This pin is the buffered internal ground connection for the external PDM capacitors. Pin 18 - AGNDC This pin serves as internal ground connection for the analog circuitry. It must be connected to analog ground with a 4.7 F and a 100 nF capacitor in parallel. Pin 19 - VREF1 This pin must be connected separately to the single ground point. It serves as ground connection for the analog bias circuits. Pin 20 - GNDA This pin serves as ground connection for the analog signals and NF parts of the synthesizer section. MICRONAS INTERMETALL Pin 31 - VSUP1 Synthesizer supply voltage 1; power is supplied via this pin for the synthesizer circuitry of the CAP 3001 A. Pin 32 - AMOSCREF Capacitor pin for AMOSCIN reference voltage. Pin 33 - AMOSCIN Input for the AM oscillator signal. Pin 34 - FMOSCREF Capacitor pin for FMOSCIN reference voltage. Pin 35 - FMOSCIN Input for the FM oscillator signal. Pin 36 - GNDS1 This pin serves as ground connection for the HF parts of the synthesizer section. Pin 37 - TESTEN Test mode enable Pin 38 - QX1 Crystal pin. This pin has to be connected with the crystal. 21 CAP 3001 A Pin 39 - QX2/ECLK Crystal pin. This pin has to be connected with the crystal or with an external clock signal. Pin 55 - WSI DAI-Bus: word select input; this is a control line to separate left and right channel in the serial DAI stream. Pin 40 - RESET In the steady state, high level is required at this pin. A low level resets the CAP 3001 A. Pin 56 - SDIN1 DAI-Bus: serial data input 1. Pins 41 to 43 - IMDATA, IMCLK, IMIDENT Via these pins the CAP 3001 A sends and receives data to and from the controller. Pin 44 - TEOSC Test purpose. Pin 45 - REFCLK Input for the synthesizer reference frequency. Pins 46 to 48 - TI1, TI2, TI3 Static digital inputs; these signals can be used as a branch condition in the DSP software. If not used, they must be connected to GND. Pins 57 to 59 - TO1, TO2, TO3 Digital outputs; the logical state can be defined by the DSP software. Pin 60 - GNDD This pin serves as ground connection for the digital signals. Pin 61 - VSUPD Digital supply voltage. Power is supplied via this pin for the digital circuitry of the CAP 3001 A. Pin 62 - CLKOUT This output is used for clocking external hardware. Pin 49 - SCLKO DAI-Bus: serial clock output. Pin 63 - TP3 Test purpose. Pin 50 - WSO DAI-Bus: word select output; this is a control line to separated left and right channel in the serial DAI stream. Pin 64 - TP2 Test purpose. Pin 51 - SDOUT DAI-Bus: serial data output. Pin 65 - TP4 Test purpose. Pin 52 - SDIN2 DAI-Bus: serial data input 2. Pin 66 - TP1 Test purpose. Pin 53 - ERR DAI-Bus: error input. Pin 67 - AMLEVEL Input for the AM field strength information. Pin 54 - SCLKI DAI-Bus: serial clock input. Pin 68 - MPLEVEL Input for the multipath information. 22 MICRONAS INTERMETALL CAP 3001 A 3.1.3. Pin Configuration FMLEVEL POT5/AVC MPLEVEL POT4 AMLEVEL POT3 TP1 POT2 TP4 TP2 POT1/MPX1 TP3 MPX0 CLKOUT AML VSUPD AMR AUXR AUXL 10 11 TAPER 12 TAPEL 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 GNDD 60 59 TO3 58 TO2 13 57 TO1 14 56 15 55 PDMC1 BAGNDC 16 54 17 53 ERR AGNDC 18 52 SDIN2 VREF1 GNDA 19 51 SDOUT 20 50 WSO VSUPA 21 49 SCLKO LF 22 48 TI3 LR RR 23 47 TI2 24 46 TI1 RF 25 45 44 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 PDMC3 PDMC2 VREF2 CAP 3001 A FMTUNOUT SDIN1 WSI SCLKI REFCLK TEOSC IMIDENT TUNFB IMCLK AMTUNOUT IMDATA VSUP2 RESET VSUP1 QX2/ECLK AMOSCREF QX1 AMOSCIN TESTEN FMOSCREF GNDS1 FMOSCIN Fig. 3-2: Pinning of the CAP 3001 A in PLCC68 package, top view MICRONAS INTERMETALL 23 CAP 3001 A 3.1.4. Electrical Characteristics All voltages refer to ground. 3.1.5. Absolute Maximum Ratings Symbol Parameter Pin No. Min. Max. Unit TA Ambient Operating Temperature - *20 )85 C TS Storage Temperature - *55 )125 C VSUP Supply Voltage 21, 61 *0.3 1) )6 V VSUP1 Supply Voltage 31 *0.3 1) )6 V VSUP2 Supply Voltage 30 *0.3 1) )12 V PTOT Chip Power Dissipation 68-pin PLCC without heatspreader 21, 61, 30, 31 - 1300 mW dVSUP Voltage between VSUPA, VSUPD and VSUP1 21, 61, 31 * 0.5 ) 0.5 V VI Input Voltage, all Inputs 1 to 17, 28, 32 to 35, 38, 39, 41 to 48, 52 to 56, 67, 68 *0.3 VSUP )0.3 V IO Output Current, all Outputs 22 to 25, 27, 29, 41, 49 to 51, 57 to 59, 62 - 2) 3) - 1) Reversed supply 200 ms maximum. 2) The outputs are short-circuit proof (max. 5 seconds) with respect to supply 3) Total chip power dissipation must not exceed absolute maximum ratings. and ground. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or any other conditions beyond those indicated in the Recommended Operating Conditions/Characteristics of this specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 3.1.6. Recommended Operating Conditions at TA+*20 to )85 C, fECLK+16.416 MHz, typical values at Tj = 27 C, duty cycle = 50 % 24 Symbol Parameter Pin No. Min. Typ. Max. Unit VSUP Supply Voltage 21, 61 4.75 5.0 5.25 V VSUP1 Supply Voltage 31 4.75 5.0 5.25 V VSUP2 Supply Voltage 30 7.5 8.5 9.5 V MICRONAS INTERMETALL CAP 3001 A Recommended Operating Conditions, continued Symbol Parameter Pin No. Min. Typ. Max. Unit VECLKL ECLK Clock Input Low Voltage 39 - - 1.5 V VECLKH ECLK Clock Input High Voltage VSUP *1.5 - - V tECLKH tECLKL ECLK Clock Input High/Low Ratio 0.9 1.0 1.1 - fECLK ECLK Clock Input Frequency (see also chapter 3.1.7.) - 16.416 - MHz VREFCLKH Reference Clock Input High Voltage VSUPD -1.5 - - V VREFCLKL Reference Clock Input Low Voltage - - 1.5 V VREFCLK0 Reference Clock Input Open Circuit Voltage fREFCLK Refence Clock Input Frequency VFS DC Input Voltage FM, AM, MP level VPOT/ MPXI 45 VSUP - 2 1 16 MHz 1, 67, 68 0 VSUP - DC Input Voltage POT5, POT4, POT3, POT2, POT1 (with Iv20 mA) 2 to 6 0 VSUP - VIH High Level, Digital Inputs 46 to 50, 52 to 56 2.0 VIL Low Level, Digital Inputs VREIL Reset Input Low Voltage VREIH Reset Input High Voltage VIMIL IM Bus Input Low Voltage VIMIH 0.8 V - - 0.8 V VSUP- 0.8V - - - - - 1.5 V IM Bus Input High Voltage 3.0 - - V fI I IM Bus Clock Frequency 0.05 - 1000 kHz tIM1 I Clock Input Delay Time after IM Bus Ident Input 0 - - - tIM2 I Clock Input Low Pulse Time 0.5 - - s tIM3 I Clock Input High Pulse Time 0.5 - - s tIM4 I Clock Input Setup Time before Ident Input High 0 - - - tIM5 I Clock Input Hold Time after Ident Input High 0.25 - - s I Clock Input Hold Time after Ident Input High defined by DSP software write data tIM5 read data tIM6 I Clock Input Setup Time before Ident End-Pulse Input MICRONAS INTERMETALL 40 V 41 to 43 41 to 43 1.0 - s - s 25 CAP 3001 A Recommended Operating Conditions, continued Symbol Parameter tIM7 Pin No. Min. Typ. Max. Unit IM Bus Data Input Delay after I Time Clock Input 0 - - - tIM8 IM Bus Data Input Setup Time before I Clock Input 0 - - - tIM9 IM Bus Data Input Hold Time after I Clock Input 0 - - - tIM10 IM Bus Ident End-Pulse Low Time 1.0 - - s CPDM PDM Capacitor (Low Loss Type) 14 to 16 *5% 680 )5% pF CAGNDC AGNDC-Filter-Capacitor 18 Ceramic Capacitor in parallel fSCLKI Input SCLKI Frequency tSIJ 54 3.3 F 100 nF - - 3.1 MHz Input SCLKI Phase Jitter - - 250 ps tSIW Input SCLKI Pulse Width 40 50 60 % tIDS Input Data Setup Time 40 - - ns tIDH Input Data Hold Time 0 - - - tWSS Input WSI Setup Time Output WSO Setup Time 40 - - ns tWSH Input WSI Hold Time Output WSO Hold Time 0 - - - 56, 52 50, 55 3.1.7. Recommended Crystal Characteristics Symbol Parameter Min. Typ. Max. Unit TA Ambient Operating Temperature *20 - )85 C fP Parallel Resonance Frequency - 16.4161) - MHz fS fS Accuracy of Adjustment - - $20 ppm fS fS Frequency Deviation versus Temperature - - $40 ppm Rr Series Resistance - - 15 C0 Shunt Capacitance 5.5 - 7 pF C1 Motional Capacitance 25 30 - fF df Frequency pulling range 350 - - ppm 1) at CL+10.7 pF. Remark on defining the external load capacitance: External capacitors at each crystal pin to ground are required. The higher the capacity, the lower the clock fre- 26 quency results. Due to different layouts of customer PCBs, the matching capacitor size should be defined in the application. MICRONAS INTERMETALL CAP 3001 A 3.1.8. Characteristics at TA+*20 to )85 C, VSUP and VSUP1+4.75 to 5.25 V, VSUP2+7.5 to 9.5 V, fECLK+16.416 MHz, typical values at VSUP and VSUP1+5.0 V, VSUP2+8.5 V, Tj= 27C and duty cycle = 50 %. Symbol Parameter Pin No. Min. Typ. Max. Unit ZAII1 Analog Input Impedance (fsignal+1kHz, i+10 A) AVC, MPX1, MPX0, AM, AUX, TAPE at Tj = 27C at Tj = *20 to )85 C 2, 6 to 13 27 26 35 43 47 k ZAII2 Analog Input Impedance FM, AM, MP level 1, 67, 68 200 k ZPOT Analog Input Impedance POT1...5 2 to 6 200 k VOSCI0 Open Circuit Voltage FMOSCIN, AMOSCIN 33, 35 VSUP1 2 - ROPOT Output Resistance POT1 to 5 as outputs, iv5 mA 2 to 6 80 ROSCI Analog Input Resistance FMOSCIN, AMOSCIN, FMOSCREF, AMOSCREF at Tj =)27 C at Tj =*20 to )85 C 33, 35 Analog Output Resistance LF, LR, RR, RF (fsignal+1kHz, i+1 mA) at Tj = 27C, at Tj =*20 to)85 C 22 to 25 VMPX0/1I Input Voltage MPX0, MPX1 VAML/RI VTAPER/ 3.2 2.1 3.6 3.6 4 4.2 6.5 k k pF 470 440 600 730 790 7, 6 2.0 VPP Input Voltage AML, AMR 8, 9 1.1 VRMS Input Voltage TAPER, TAPEL 12, 13 1.6 VRMS VAUXR/LI Input Voltage AUXR, AUXL 10, 11 1.1 VRMS VAVCI Input Voltage AVC 2 0.007 VRMS VAICL Analog Audio Input Clipping Level (defines 0 dBr) 6 to 13 Max. Input Voltage ZAOL Analog Output Load 22 to 25 6 0.005 VAOV Maximum Analog Output Voltage LF, LR, RR, RF (output attenuation +0 dB, analog output load u 100 k) Analog Input Digital Input 22 to 25 VAMOSC AM OSC Input Voltage 33 fAMOSCI AM OSC Input Frequency Range RAO TAPELI MICRONAS INTERMETALL Max. Input Voltage +1 dB Max. Input Voltage + 2 dB 1 k nF 1.0 1.1 VRMS 40 300 mVRMS 0.5 20 MHz 0.8 0.9 0.9 1.0 27 CAP 3001 A Characteristics, continued 28 Symbol Parameter Pin No. Min. Typ. Max. Unit VFMOSCI FM OSC Input Voltage 35 40 300 mVRMS fFMOSCI FM OSC Input Frequency Range 60 150 MHz SNRAD SNR A/D (Noise measurement RMS unweighted, BW+20 to 18000 Hz, input level+*20 dBr, fsignal+1kHz) 7 to 13 SNRDA SNR D/A Analog Attenuation+0 dB Analog Attenuation+45 dB in MUTE position (RMS, unweighted, BW+20 to 20000 Hz1), input level+*20 dBFS, fsignal+1kHz) 22 to 25 SNRRDS1 SNR A/D selected MPX ARI/RDS channel (Noise measurement RMS, unweighted, BW+55 to 59 kHz, input level+55 mVPP fsignal+57 kHz) 6, 7 THDAD THD A/D (RMS, unweighted, BW+20 to 18000, input level+*3 dBr, fsignal+1 kHz) 7 to 13 0.03 % THDDA THD D/A (BW+20 to 20000 Hz1), input level+*3 dBFS, fsignal+1kHz, analog attenuation+0 dB) 22 to 25 0.01 % IMDAD Intermodulation Distortion A/D (fsignal+14 kHz)15 kHz, input level sum*3 dBr, measuring 1 kHz intermodulation)2) 7 to 13 XTALK1 Crosstalk attenuation within active audio channel pair (input level +*3 dBr, fsignal+1kHz, measuring with bandpass at 1 kHz)2) 8 to 13 70 dB XTALK2 Crosstalk attenuation from a nonselected audio input pair (input level+*3 dBr, fsignal+1kHz, measuring with bandpass at 1 kHz)2) 7 to 13 80 dB XTALK3 Crosstalk attenuation between audio input/output pairs (input level+*3 dBr, fsignal+1kHz, measuring with bandpass at 1 kHz)2) 7 to 13, 22 to 25 100 dB 82 85 dB 90 60 95 65 110 dB dB dB 38 dB 0.01 % MICRONAS INTERMETALL CAP 3001 A Characteristics, continued Symbol Parameter Pin No. CHSEPMPX Stereo separation MPX 250 Hz to 6.3 kHz 6.3 kHz to 12.5 kHz (coupling capacitor on MPX input at least 1F) 7 SNRMPX 19 kHz SNRRDS2 Suppression of unwanted signals in MPX stereo reception: 19 kHz 38 kHz 57 kHz 114 kHz measuring with bandpass at fsignal Min. Typ. Max. Unit 40 30 dB dB 45 45 60 60 dB dB dB dB 60 70 dB dB Alias Band Suppression in RDS Channel (fsignal+57 kHz, input level+55 mVPP) @ 171 kHz @ 285 kHz 6, 7 SNRAVC SNR A/D3 selected AVC channel (Noise measurement RMS unweighted, BW+0 to 4 kHz, input level+*20 dBr, fsignal+1 kHz) 2 40 dB SNRAD4 SNR A/D4 (Noise measurement RMS unweighted, BW+0 to 7 kHz, input level+*20 dBr, fsignal+1 kHz) 1, 67, 68 50 dB THDAVC THD A/D3 selected AVC channel (RMS unweighted, BW+0 to 4 kHz, input level+*3 dBr, fsignal+1 kHz) 2 2.2 % THDAD4 THD A/D4 (RMS unweighted, BW+0 to 7 kHz, input level+*3 dBr, fsignal+1 kHz 1, 67, 68 3.2 % BWADDA 3 dB Bandwidth A/D to D/A TAPE, AUX (not provided in production test) 10 to 13, 22 to 25 BWDA 3 dB Bandwidth D/A @fs=32 kHz @fs=44.1 kHz (not provided in production test) 22 to 25 Channel deviation within active input pair: AUX, TAPE AM 8 to 13 Channel deviation within each output of: RR, RF, LR, LF Analog attenuation = 0 to*30 dB = *31.5 to*45 dB 22 to 25 dGAD dGDA MICRONAS INTERMETALL 18 kHz 15 20 kHz kHz dB 0.5 0.7 0.5 0.9 dB 29 CAP 3001 A Characteristics, continued Symbol Parameter Pin No. Min. dGAVOL Analog Volume Step Size (*45 dB to 0 dB) 22 to 25 1.4 IREIL Reset Input Leakage Current 40 *10 ISUP Supply Current Max. Unit 1.6 dB - )10 A 61 21 31 30 60 12 8 1.4 85 20 11 2.2 110 28 14 3 mA VIMOL IM Bus Data Output Low Voltage 41 - - 0.4 V VIMOH IM Bus Data Output High Voltage 2.8 - - V IIMOHL IM Bus Data Output High-Impedance Leakage Current *10 - )10 A IIMIL IM Bus Input Leakage Current *10 - )10 A VTOH VTOL Digital Output High Voltage Digital Output Low Voltage 57 to 59 4.0 - VTIH VTIL Digital Input High Voltage Digital Input Low Voltage 46 to 48 VTUNOUT Synthesizer Output Voltage AMTUNOUT, FMTUNOUT 27, 29 1.1 - VSUP2 *1.1 V VAGNDC0 AGNDC Open Circuit Voltage 18 2.15 2.25 2.35 V ROUTAGND AGNDC Output Resistance at 27 C at *20 to )85 C 18 110 70 125 140 230 k k dVBAGNDC Dev. of BAGNDC from AGNDC Vol. 17, 18 *20 )20 mV ROUTBAGND BAGNDC Output Resistance (fsignal+1kHz, i+0.1 mA) 17 dVDAC Deviation of DC Level at Audio Outputs from AGNDC Voltage 18, 22 to 25 *20 IOUTSYNTH Synthesizer Current Source Accuracy 27, 29 3.3 33 330 PSRR Power Supply Rejection Ratio 1 kHz 20 Hz to 20 kHz 21, 61, 31, 30, 22 to 25 dVTUNOUT 1) 2) 30 VSUPD VSUPA VSUP1 VSUP2 Residual Noise of Synthes. Output Volt. (BW 22Hz to 22 kHz, i+5 A) Typ. 1.5 V 0.4 2.4 - V 0.8 6 5 50 500 )20 mV 6.5 70 740 A dB 50 40 2.2 V CD-Mode, fs+44.1 kHz unused analog inputs connected to ground MICRONAS INTERMETALL CAP 3001 A 4. Starting the Processor 5. Synthesizer After power-up, the crystal oscillator has to have been started before the Reset reaches high level. An additional wait time of 0.4 ms has to be taken into account because of a DSP-internal self-test algorithm. Then a defined start of the system can take place. Fig. 4-1 shows the complete startup sequence of the typical application. With the synthesizer block in the CAP 3001 A, a PLL tuning system can be implemented for FM and AM receivers. The signal picked up from the mixing oscillators of the FM and AM tuners can be fed to the synthesizer block by means of highly sensitive input pins. Freely programmable dividers, operating with frequencies up to and over 100 MHz, scale the incoming signals to a reference frequency of 25 kHz. This holds true even in the case of AM, which gives AM tuning a considerable speed improvement over common designs. In order to get a tuning step size of down to 300 Hz, the reference divider is also programmable. Incoming frequencies in the range of 0.5 MHz up to more than 100 MHz can be handled, so that the designer is free to choose either a 10.7 MHz or a 450 to 460 kHz IF frequency for the AM case. The common reference frequency for AM and FM allows the implementation of a common PLL filter for the tuning output. The DCO register is loaded with a precisely definedmean value. VSUPD VSUPA 4.75 V Crystal Oscillator 2.4 V Reset > 1 ms > 0.4 ms Fig. 4-1: Startup sequence FMOSCIN FMOSCREF ) * Programmable Divider (16 bit) Programmable Divider (10 bit) Current Source Reference Clock 16.416 MHz or external REFCLK AMOSCREF * AMOSCIN ) FMTUNOUT Filter Filter AMTUNOUT Gain adjust Fig. 5-1: Synthesizer block diagram MICRONAS INTERMETALL 31 CAP 3001 A 6. Application Notes 10.7 MHz FM FM Preselection FM MPX IF Osc. FMLEVEL FMOSCIN FMTUNOUT CAP 3001 A AMTUNOUT AMOSCIN AMLEVEL Osc. Osc. AM 455 kHz AM IF Preselection AM audio 10.7 MHz Fig. 6-1: CAP 3001 A application for 10.7 MHz AM-IF in detail 32 MICRONAS INTERMETALL CAP 3001 A 7. Typical Application Circuit k. s k. s k. s k. s k. s k. s CAP 3001 A These values have to be adjusted to achieve the neccessary pulling range (compensation of the parasitic boardcapacities). These ground nets are connected together to the main ground under the IC, close to the pin VREF1. Pin VREF2 is the reference for the tuning synthesizer. It is connected to the tuner ground and has no direct connection to the main ground under the IC. This is the ground at the tuner. It has a separate connection to the main ground under the IC. k. s. Keep these leads as short as possible! MICRONAS INTERMETALL 33 CAP 3001 A 8. Index A A/D Converters, 8 Absolute Maximum Ratings, 24 Interpolation, 8 M MPX Signal, 6, 7 Analog Input Signals, 7 Analog Outputs, 12 Analog Volume Control, 12 Application Circuit, 33 ARI Travel Information, 11 ASU Noise Canceller, 12 B Block Diagram CAP 3001 A, 5 C O Operating Modes, 6 Oscillator, 17 Outline Dimensions, 18 Oversampling, 12 P Pilot Tone, 9 Pin Configuration, 23 Pin Connections and Short Descriptions, 18 Characteristics, 27 Potentiometer Inputs, 7 Clock Generation, 17 Power-Up Sequence, 31 Crystal, 17, 27 D R RDS, 6, 7, 11 D/A Converters, 12 Recommended Operating Conditions, 24 DCO, 17 Reset, 31 Decimation, 8 S Digital Audio Interface, 13 SNR, 28 Digital Filters, 8 Stereo Mixer, 8 DSP, 4, 5 Stereo PLL, 8 F FM/AM Tuning, 31 I I2S-bus, 13 IM-Bus Interface, 15 Input Signals, 7 34 Synthesizer, 31 T THD+N, 28 Tuning System, 31, 32 V Volume Control, 12 MICRONAS INTERMETALL CAP 3001 A MICRONAS INTERMETALL 35 CAP 3001 A 9. Data Sheet History: 1. Final data sheet: "CAP 3001 A Car Audio Processor Hardware", April 4, 1996, 6251-365-1DS. First release of the final data sheet. MICRONAS INTERMETALL GmbH Hans-Bunte-Strasse 19 D-79108 Freiburg (Germany) P.O. Box 840 D-79008 Freiburg (Germany) Tel. +49-761-517-0 Fax +49-761-517-2174 E-mail: docservice@intermetall.de Internet: http://www.intermetall.de Printed in Germany by Simon Druck GmbH & Co., Freiburg (04/96) Order No. 6251-365-1DS 36 All information and data contained in this data sheet are without any commitment, are not to be considered as an offer for conclusion of a contract nor shall they be construed as to create any liability. Any new issue of this data sheet invalidates previous issues. Product availability and delivery dates are exclusively subject to our respective order confirmation form; the same applies to orders based on development samples delivered. By this publication, MICRONAS INTERMETALL GmbH does not assume responsibility for patent infringements or other rights of third parties which may result from its use. Reprinting is generally permitted, indicating the source. However, our prior consent must be obtained in all cases. MICRONAS INTERMETALL