Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type: B41853, B41863
Date: November 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Long-life grade capacitors
Applications
Automotive electronics: energy reserve for airbag application
Features
Compact design
High CV product
B41853, designed for severe charge and discharge conditions
B41863, designed for standard charge and discharge
conditions
Construction
Radial leads
Charge/discharge-proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Stand-off rubber seal
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut
Kinked
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details and ordering
example.
Single-ended capacitors B41853, B41863
For airbag applications 105 °C
Page 2 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR25 and 35 V DC
Surge voltage VS1.15 VR
Rated capacitance CR680 ... 10000 µF
Capacitance tolerance 0/+30% A
Dissipation factor tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR(V DC) 25 35
tan δ(max.) 0.16 0.14
Leakage current Ileak
(20 °C, 5 min)
Self-inductance ESL Diameter (mm) 12.5 16 18
ESL (nH) 20 26 34
Useful life
105 °C; VR; IAC,R > 3000 h
Requirements C/C ±30% of initial value
tan δ 3 times initial specified limit
Ileak initial specified limit
Voltage endurance test
105 °C; VR3000 h
Post test requirements C/C ±25% of initial value
tan δ 2 times initial specified limit
Ileak initial specified limit
Vibration resistance test To IEC 60068-2-6, test Fc:
Displacement amplitude 1.5 mm, frequency range 10 2000 Hz,
acceleration max. 20 g, duration 3 ×2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category To IEC 60068-1:
55/105/56 (55 °C/+105 °C/56 days damp heat test)
Sectional specification AEC-Q200, IEC 60384-4
Charge and discharge
characteristics
B41853 B41863
Acc. to IEC 60384-4,
AEC-Q200 and addendum 1
(see next page)
Acc. to IEC 60384-4 and AEC-Q200
B41853, B41863
For airbag applications 105 °C
Page 3 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Addendum 1:
B41853, charge and discharge test specification
25 V 35 V
tC= tD= 2s R122.8
R225 35
Duration: 2000 h
Temperature: thermal cycling -40/85°C acc. to AEC-Q200 specification
Higher resistances (R1and R2) and longer test periods (tCand tD) are allowed when respecting
the temperatures and the total test duration specified above
For any other requirement condition, please contact your nearest EPCOS representation
B41853, B41863
For airbag applications 105 °C
Page 4 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing
With stand-off rubber seal
Diameters (mm): 10, 12.5, 16, 18
Dimensions and weights
Dimensions (mm) Approx. weight
d +0.5 l a ±0.5 b g
10 20 +2.0 5.0 0.60 ±0.05 2.6
12.5 20 +2.0 5.0 0.60 ±0.05 3.6
12.5 25 +2.0 5.0 0.60 ±0.05 4.5
16 20 +2.0 7.5 0.80 ±0.05 5.5
16 25 +2.0 7.5 0.80 ±0.05 7.5
16 31.5 +2.0 7.5 0.80 ±0.05 7.8
18 20 +2.0 7.5 0.80 ±0.1 8.9
18 25 +2.0 7.5 0.80 ±0.1 9.0
18 31.5 +2.0 7.5 0.80 ±0.1 11.0
18 35 +2.0 7.5 0.80 ±0.1 13.0
18 40 +2.5 7.5 0.80 ±0.1 16.0
B41853, B41863
For airbag applications 105 °C
Page 5 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR(V DC) 25 35
Case dimensions d ×l (mm)
CR(µF)
680 10 ×20
820 12.5 ×20
1000 10 ×20 12.5 ×25
16 ×20
1200 12.5 ×20 16 ×20
1500 12.5 ×20 16 ×20
1800 12.5 ×25 16 ×20
2200 16 ×20 18 ×20
2400 18 ×20
2700 16 ×20 18 ×25
3300 18 ×20 18 ×25
3900 18 ×25 18 ×31.5
4700 18 ×25 18 ×35
5600 18 ×31.5 18 ×40
6500 18 ×31.5 18 ×40
6800 18 ×35
7500 18 ×35
8200 18 ×40
10000 18 ×40
Other voltage and capacitance ratings are available upon request.
B41853, B41863
For airbag applications 105 °C
Page 6 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
ESRmax
120 Hz
20 °C
ESRmax
10 kHz
20 °C
Zmax
100 kHz
20 °C
IAC,R
100 kHz
105 °C
mA
IAC,max
100 kHz
85 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
# = Version *** = Version
5 = for severe charge and discharge conditions
6 = for standard charge and discharge conditions
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d ×l=10×20
mm to 18 ×40 mm)
002 = for cut leads, bulk (for ∅≥10 mm)
003 = for crimped leads, blister (from d ×l=10×
20 mm to 18 ×40 mm)
004 = for J leads, blister (from d ×l=10×20 mm
to 18 ×35 mm)
008 = for taped leads, Ammo pack, lead spacing
F = 5.0 mm (for d ×l=10×20 mm)
009 = for taped leads, Ammo pack, lead spacing
F = 7.5 mm (from d ×l=16×20 mm to
18 ×31.5 mm)
012 = for bent 90°leads, blister (for 16 and 18
mm)
VR= 25 V DC
1000 10 ×20 1.264 0.253 0.158 0.136 875 1181 B418#3A5108A***
1200 12.5 ×20 0.784 0.211 0.098 0.085 1105 1492 B418#3A5128A***
1500 12.5 ×20 0.784 0.168 0.098 0.085 1105 1492 B418#3A5158A***
1800 12.5 ×25 0.712 0.140 0.089 0.078 1358 1833 B418#3A5188A***
2200 16 ×20 0.664 0.129 0.083 0.075 1895 2558 B418#3A5228A***
2700 16 ×20 0.664 0.105 0.083 0.075 1895 2558 B418#3A5278A***
3300 18 ×20 0.480 0.096 0.060 0.054 2190 2957 B418#3A5338A***
3900 18 ×25 0.400 0.081 0.050 0.045 2454 3313 B418#3A5398A***
4700 18 ×25 0.400 0.074 0.050 0.045 2454 3313 B418#3A5478A***
5600 18 ×31.5 0.376 0.068 0.047 0.042 3178 4290 B418#3A5568A***
6500 18 ×31.5 0.376 0.063 0.047 0.042 3178 4290 B418#3A5658A***
6800 18 ×35 0.320 0.060 0.040 0.036 3638 4911 B418#3A5688A***
7500 18 ×35 0.320 0.059 0.040 0.036 3638 4911 B418#3A5758A***
8200 18 ×40 0.224 0.058 0.028 0.026 4164 5621 B418#3A5828A***
10000 18 ×40 0.224 0.054 0.028 0.026 4164 5621 B418#3A5109A***
B41853, B41863
For airbag applications 105 °C
Page 7 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
ESRmax
120 Hz
20 °C
ESRmax
10 kHz
20 °C
Zmax
100 kHz
20 °C
IAC,R
100 kHz
105 °C
mA
IAC,max
100 kHz
85 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
# = Version *** = Version
5 = for severe charge and discharge conditions
6 = for standard charge and discharge conditions
000 = for standard leads, bulk
001 = for kinked leads, bulk (from d ×l=10×20
mm to 18 ×40 mm)
002 = for cut leads, bulk (for ∅≥10 mm)
003 = for crimped leads, blister (from d ×l=10×
20 mm to 18 ×40 mm)
004 = for J leads, blister (from d ×l=10×20 mm
to 18 ×35 mm)
008 = for taped leads, Ammo pack, lead spacing
F = 5.0 mm (for d ×l=10×20 mm)
009 = for taped leads, Ammo pack, lead spacing
F = 7.5 mm (from d ×l=16×20 mm to
18 ×31.5 mm)
012 = for bent 90°leads, blister (for 16 and 18
mm)
VR= 35 V DC
680 10 ×20 1.264 0.325 0.158 0.136 875 1181 B418#3A7687A***
820 12.5 ×20 0.784 0.270 0.098 0.085 1105 1492 B418#3A7827A***
1000 12.5 ×25 0.712 0.221 0.089 0.078 1358 1833 B418#3A7108A***
1000 16 ×20 0.664 0.221 0.083 0.075 1895 2558 B418#3B7108A***
1200 16 ×20 0.664 0.184 0.083 0.075 1895 2558 B418#3A7128A***
1500 16 ×20 0.664 0.147 0.083 0.075 1895 2558 B418#3A7158A***
1800 16 ×20 0.664 0.123 0.083 0.075 1895 2558 B418#3A7188A***
2200 18 ×20 0.480 0.115 0.060 0.054 2190 2957 B418#3A7228A***
2400 18 ×20 0.480 0.105 0.060 0.054 2190 2957 B418#3A7248A***
2700 18 ×25 0.400 0.094 0.050 0.045 2454 3313 B418#3A7278A***
3300 18 ×25 0.400 0.086 0.050 0.045 2454 3313 B418#3A7338A***
3900 18 ×31.5 0.376 0.073 0.047 0.042 3178 4290 B418#3A7398A***
4700 18 ×35 0.320 0.067 0.040 0.036 3638 4911 B418#3A7478A***
5600 18 ×40 0.224 0.062 0.028 0.026 4164 5621 B418#3A7568A***
6500 18 ×40 0.224 0.058 0.028 0.026 4164 5621 B418#3A7658A***
B41853, B41863
For airbag applications 105 °C
Page 8 of 27Please read Cautions and warnings and
Important notes at the end of this document.
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
Frequency factor of permissible ripple current IAC versus frequency f
B41853, B41863
For airbag applications 105 °C
Page 9 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows:
Lead spacing F = 2.5 mm (d=5 6.3 mm)
Lead spacing F = 3.5 mm (d = 8 mm)
Lead spacing F = 5.0 mm (from d ×l=10×12.5 mm to 12.5 ×30 mm)
Lead spacing F = 7.5 mm (d = 16 ... 18 mm).
Lead spacing 2.5 mm (d = 5 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
d F H W W0W1W2H0P P0P1I1th D0
52.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
6.3
Toler-
ance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
B41853, B41863
For airbag applications 105 °C
Page 10 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 3.5 mm (d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
d F H W W0W1W2P P0P1I1th D0
83.5 18.5 18.0 12.5 9.0 1.5 12.7 12.7 4.6 1.0 0.7 1.0 4.0
Toler-
ance
+0.8
0.2 ±1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
B41853, B41863
For airbag applications 105 °C
Page 11 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (d = 5 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (from d ×l=10×12.5 mm to 12.5 ×30 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
d F H W W0W1W2H0P P0P1I1th D0
55.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.7 1.0 4.0
6.3
820.0 16.0 12.7 12.7 3.85
10 5.0 19.0 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.7 1.0 4.0
12.5 19.0 15.0 15.0 5.0
Toler-
ance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
B41853, B41863
For airbag applications 105 °C
Page 12 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 7.5 mm (d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
d F H W W0W1W2P P0P1I1tPh D0
16 7.5 18.5 18.0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0
18 *)
Toler-
ance ±0.8 0.5
+0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2
*) Available only for case dimensions 18 ×20, 18 ×25 and 18 ×31.5 mm
B41853, B41863
For airbag applications 105 °C
Page 13 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Packing units and box dimensions
Ammo pack
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
5×11 345 55 240 2000
6.3 ×11 345 55 290 2000
8×11.5 345 55 240 1000
10 ×12.5 345 55 280 750
10 ×16 345 60 200 500
10 ×20 345 60 200 500
12.5 ×20 345 65 280 500
12.5 ×25 345 65 280 500
16 ×20 315 65 275 300
16 ×25 315 65 275 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B41853, B41863
For airbag applications 105 °C
Page 14 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also
available upon request.
Kinked leads
Last 3 digits of ordering code: 001
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B41853, B41863
For airbag applications 105 °C
Page 15 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads
Last 3 digits of ordering code: 002
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×12.5 5.0
10 ×16 5.0
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
20 ×20 10.0
20 ×25 10.0
20 ×30 10.0
20 ×35 10.0
20 ×40 10.0
22 ×30 10.0
22 ×35 10.0
22 ×40 10.0
With flat rubber seal
B41853, B41863
For airbag applications 105 °C
Page 16 of 27Please read Cautions and warnings and
Important notes at the end of this document.
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 20 mm.
There are three configurations available: Crimped leads, J leads, bent 90°leads
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal With flat rubber seal
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 a ±0.5 b
16 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
18 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
20 ×20 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1
20 ×25 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1
20 ×30 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1
20 ×35 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1
20 ×40 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1
B41853, B41863
For airbag applications 105 °C
Page 17 of 27Please read Cautions and warnings and
Important notes at the end of this document.
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 J ±0.2 a ±0.5 b
10 ×12.5 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×16 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×25 3.2 0.7 1.2 5.0 0.6 ±0.05
16 ×20 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×25 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.05
18 ×20 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×25 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×35 3.5 0.7 1.6 7.5 0.8 ±0.1
B41853, B41863
For airbag applications 105 °C
Page 18 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Bent 90°leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 b
16 ×20 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×25 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×31.5 4.0 4.0 12.0 7.5 0.8 ±0.05
18 ×20 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×25 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×31.5 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×35 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×40 4.0 4.0 13.0 7.5 0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
B41853, B41863
For airbag applications 105 °C
Page 19 of 27Please read Cautions and warnings and
Important notes at the end of this document.
1) Available upon request
Overview of packing units and code numbers for case sizes 5 ×11 ... 16 ×31.5
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
5×11 2000 2000
6.3 ×11 2500 2000
8×11.5 1000 1000
10 ×12.5 1000 750 1000 675
10 ×16 1000 500 1000 675
10 ×20 500 500 500 500 500
12.5 ×20 350 500 350 350 300 1)
12.5 ×25 250 500 500 500 225 1)
12.5 ×30 200
12.5 ×35 175
12.5 ×40 175
16 ×20 250 300 200 200 200 200 120
16 ×25 250 300 200 200 200 200 120
16 ×31.5 200 300 250 250 344 344 120
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
006
007
008
009
3.5
2.5
5
7.5
8
5...6.3
5...12.5
16...18
B41853, B41863
For airbag applications 105 °C
Page 20 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 ×20 ... 25 ×40
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
18 ×20 175 250 175 175 200 200 120
18 ×25 150 250 150 150 200 200 120
18 ×31.5 100 250 100 100 150 150 120
18 ×35 100 100 100 150 150 150
18 ×40 125 100 100 120 72
20 ×20 125 125 200
20 ×25 125 125 200
20 ×30 100 100 120
20 ×35 100 100 120
20 ×40 100 100 120
22 ×30 80 100
22 ×35 80 100
22 ×40 80 100
25 ×40 40
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
007
008
009
2.5
5
7.5
4...6.3
6.3...12.5
16...18
B41853, B41863
For airbag applications 105 °C
Page 21 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
B41853, B41863
For airbag applications 105 °C
Page 22 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic Safety information Reference
Chapter "General
technical information"
Polarity Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage Voltages polarity classes should be prevented by
connecting a diode.
3.1.6
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperatur. 7.2
"Maximum permissible
operating temperature"
Maintenance Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
10
"Maintenance"
Mounting
position of screw
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
11.4
"Mounting
considerations for
single-ended capacitors"
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
11.3
"Mounting torques"
Soldering Do not exceed the specified time or temperature
limits during soldering.
11.5
"Soldering"
B41853, B41863
For airbag applications 105 °C
Page 23 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Topic Safety information Reference
Chapter "General
technical information"
Soldering,
cleaning agents
Do not allow halogenated hydrocarbons to come
into contact with aluminum electrolytic capacitors.
11.6
"Cleaning agents"
Passive
flammability
Avoid external energy, such as fire or electricity. 8.1
"Passive flammability"
Active
flammability
Avoid overload of the capacitors. 8.2
"Active flammability"
Reference
Chapter "Capacitors
with screw terminals"
Breakdown strength
of insulating
sleeves
Do not damage the insulating sleeve, especially
when ring clips are used for mounting.
"Screw terminals -
accessories"
B41853, B41863
For airbag applications 105 °C
Page 24 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Symbols and terms
Symbol English German
C Capacitance Kapazität
CRRated capacitance Nennkapazität
CSSeries capacitance Serienkapazität
CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T
CfCapacitance at frequency f Kapazität bei Frequenz f
d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß
dmax Maximum case diameter Maximaler Gehäusedurchmesser
ESL Self-inductance Eigeninduktivität
ESR Equivalent series resistance Ersatzserienwiderstand
ESRfEquivalent series resistance at
frequency f
Ersatzserienwiderstand bei Frequenz f
ESRTEquivalent series resistance at
temperature T
Ersatzserienwiderstand bei Temperatur T
f Frequency Frequenz
I Current Strom
IAC Alternating current (ripple current) Wechselstrom
IAC,rms Root-mean-square value of alternating
current
Wechselstrom, Effektivwert
IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f
IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom
IAC,R Rated ripple current Nennwechselstrom
IAC,R (B) Rated ripple current for base cooling Nennwechselstromstrom für Bodenkühlung
Ileak Leakage current Ableitstrom
Ileak,op Operating leakage current Ableitstrom bei Betrieb
l Case length, nominal dimension Gehäuselänge, Nennmaß
lmax Maximum case length (without
terminals and mounting stud)
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
R Resistance Widerstand
Rins Insulation resistance Isolationswiderstand
Rsymm Balancing resistance Symmetrierwiderstand
T Temperature Temperatur
T Temperature difference Temperaturdifferenz
TAAmbient temperature Umgebungstemperatur
TCCase temperature Gehäusetemperatur
TBCapacitor base temperature Temperatur des Becherbodens
t Time Zeit
t Period Zeitraum
tbService life (operating hours) Brauchbarkeitsdauer (Betriebszeit)
B41853, B41863
For airbag applications 105 °C
Page 25 of 27Please read Cautions and warnings and
Important notes at the end of this document.
Symbol English German
V Voltage Spannung
VFForming voltage Formierspannung
Vop Operating voltage Betriebsspannung
VRRated voltage, DC voltage Nennspannung, Gleichspannung
VSSurge voltage Spitzenspannung
XCCapacitive reactance Kapazitiver Blindwiderstand
XLInductive reactance Induktiver Blindwiderstand
Z Impedance Scheinwiderstand
ZTImpedance at temperature T Scheinwiderstand bei Temperatur T
tan δDissipation factor Verlustfaktor
λFailure rate Ausfallrate
ε0Absolute permittivity Elektrische Feldkonstante
εrRelative permittivity Dielektrizitätszahl
ωAngular velocity; 2 πf Kreisfrequenz; 2 πf
Notes
All dimensions are given in mm.
B41853, B41863
For airbag applications 105 °C
Page 26 of 27Please read Cautions and warnings and
Important notes at the end of this document.
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
Important notes
Page 27 of 27