MP 277 ___________________ Preface 1 ___________________ Overview SIMATIC HMI HMI device MP 277 Operating Instructions Safety instructions and 2 ___________________ approvals 3 ___________________ Planning application Installing and connecting the 4 ___________________ device Operator controls and 5 ___________________ displays 6 ___________________ Configuring the device 7 ___________________ Commissioning a project 8 ___________________ Operating a project 9 ___________________ Maintenance and care 10 ___________________ Technical specifications A ___________________ Appendix B ___________________ Abbreviations 07/2014 A5E02479740-02 Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by (R) are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 NURNBERG GERMANY A5E02479740-02 09/2014 Subject to change Copyright (c) Siemens AG 2014. All rights reserved Preface Purpose of the operating instructions These operating instructions provide information for manuals derived from the requirements for mechanical engineering documentation according to DIN EN 62079. This information relates to the place of use, transport, storage, mounting, use and maintenance. These operating instructions are intended for: Users Commissioning engineers Maintenance personnel Pay particular attention to the section "Safety Instructions (Page 25)". You can find more information such as operating instructions, examples and reference information in the online help of the configuration software. Required knowledge General knowledge of automation technology and process communication is needed to understand the operating instructions. It is also assumed that those using the manual have experience in using personal computers and an understanding of Microsoft operating systems. Scope of the operating instructions The operating instructions apply to the HMI device MP 277 in conjunction with the following configuration software: WinCC (TIA Portal) WinCC flexible MP 277 Operating Instructions, 07/2014, A5E02479740-02 3 Preface Conventions The following text notation will facilitate reading this manual: Notation Scope "Add screen" * Terminology that appears in the user interface, for example dialog names, tabs, buttons, menu commands * Required input, for example, limits, tag values. * Path information "File > Edit" Operating sequences, for example, menu commands, shortcut menu commands , Keyboard operation Please observe notes labeled as follows: Note Notes contain important information concerning the product, its use or a specific section of the documentation to which you should pay particular attention. Illustrations in this manual This documentation includes illustrations associated with the product. These illustrations may differ from the factory state of the product. MP 277 4 Operating Instructions, 07/2014, A5E02479740-02 Table of contents Preface ................................................................................................................................................... 3 1 2 3 4 Overview................................................................................................................................................. 9 1.1 Product overview ...................................................................................................................... 9 1.2 Design of the HMI Device MP 277 8" Touch ..........................................................................10 1.3 Design of the HMI Device MP 277 8" Key ..............................................................................11 1.4 Design of the HMI Device MP 277 10" Touch ........................................................................13 1.5 Design of the HMI Device MP 277 10" Key ............................................................................14 1.6 Accessory kit ...........................................................................................................................16 1.7 Accessories .............................................................................................................................16 1.8 The HMI device in the operating process ...............................................................................18 1.9 Functional scope with WinCC and WinCC flexible .................................................................19 1.10 Software options .....................................................................................................................21 1.11 Communications .....................................................................................................................22 Safety instructions and approvals .......................................................................................................... 25 2.1 Safety Instructions ..................................................................................................................25 2.2 Standards, certificates and approvals.....................................................................................27 2.3 Notes about usage ..................................................................................................................30 2.4 Electromagnetic compatibility .................................................................................................31 2.5 Transport and storage conditions ...........................................................................................33 Planning application .............................................................................................................................. 35 3.1 Notes about usage ..................................................................................................................35 3.2 Mounting positions ..................................................................................................................37 3.3 Preparing for Mounting ...........................................................................................................38 3.4 Specifications for Insulation Tests, Protection Class and Degree of Protection ....................40 3.5 Rated voltages ........................................................................................................................40 Installing and connecting the device ...................................................................................................... 41 4.1 Checking the package contents ..............................................................................................41 4.2 Mounting the HMI Device .......................................................................................................41 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.3.8 Connecting the HMI device .....................................................................................................44 Overview .................................................................................................................................44 Ports ........................................................................................................................................45 Connecting the equipotential bonding circuit ..........................................................................46 Connecting the Power Supply ................................................................................................48 Connecting the PLC ................................................................................................................50 Connecting a Configuring PC .................................................................................................53 Connecting a USB device .......................................................................................................55 Connecting a Printer. ..............................................................................................................57 MP 277 Operating Instructions, 07/2014, A5E02479740-02 5 Table of contents 5 6 4.4 Switching on and Testing the HMI device .............................................................................. 58 4.5 Securing the cables ............................................................................................................... 59 Operator controls and displays .............................................................................................................. 61 5.1 Front operator controls ........................................................................................................... 61 5.2 Using Memory Cards with the HMI Device ............................................................................ 63 5.3 Labeling the Function Keys at the MP 277 Key ..................................................................... 65 Configuring the device .......................................................................................................................... 69 6.1 Loader .................................................................................................................................... 69 6.2 Enabling and disabling SecureMode ..................................................................................... 74 6.3 6.3.1 6.3.2 6.3.3 6.3.3.1 6.3.3.2 6.3.3.3 Control Panel ......................................................................................................................... 74 Overview ................................................................................................................................ 74 Reference for functions .......................................................................................................... 76 Operating the Control Panel .................................................................................................. 77 Overview ................................................................................................................................ 77 Entries using the touch screen............................................................................................... 78 Input with the Keyboard ......................................................................................................... 80 6.4 6.4.1 6.4.2 6.4.3 6.4.4 Changing settings for operation ............................................................................................. 84 Setting up the screen keyboard ............................................................................................. 84 Setting the Character Repetition of the Keyboard ................................................................. 85 Setting the Double-click ......................................................................................................... 86 Calibrate touch screen ........................................................................................................... 87 6.5 Changing Password Protection.............................................................................................. 89 6.6 6.6.1 6.6.2 6.6.3 6.6.4 6.6.5 6.6.6 6.6.7 6.6.8 6.6.9 6.6.10 Changing HMI device settings ............................................................................................... 90 Setting the Date and Time ..................................................................................................... 90 Changing Regional Settings .................................................................................................. 92 Backing up Registry Information ............................................................................................ 92 Changing monitor settings ..................................................................................................... 94 Setting the screen saver ........................................................................................................ 94 Changing the Printer Properties............................................................................................. 96 Set the volume ....................................................................................................................... 97 Restarting the HMI Device ..................................................................................................... 99 Displaying Information about the HMI Device ...................................................................... 100 Displaying System Properties .............................................................................................. 101 6.7 Setting the Delay Time ......................................................................................................... 102 6.8 Setting the uninterruptible power supply .............................................................................. 104 6.9 State of uninterruptible power supply .................................................................................. 105 6.10 6.10.1 6.10.2 6.10.3 Change the communication settings .................................................................................... 106 Changing S7 transfer settings.............................................................................................. 106 Configuring the data channel ............................................................................................... 109 Enabling PROFINET IO ....................................................................................................... 111 6.11 6.11.1 6.11.2 6.11.3 6.11.4 6.11.5 Configuring network operation ............................................................................................. 113 Overview of network operation ............................................................................................ 113 Setting the device name of the HMI device ......................................................................... 115 Changing the Network Configuration ................................................................................... 116 Changing the Logon Data .................................................................................................... 118 Changing E-Mail Settings .................................................................................................... 119 MP 277 6 Operating Instructions, 07/2014, A5E02479740-02 Table of contents 7 8 6.11.6 6.11.6.1 6.11.6.2 6.11.6.3 6.11.6.4 Changing internet settings ....................................................................................................121 Changing General Internet Settings .....................................................................................121 Setting the Proxy Server .......................................................................................................122 Changing Privacy Settings ....................................................................................................123 Importing and Deleting Certificates .......................................................................................125 6.12 Backing up data to external storage device ..........................................................................126 6.13 Restoring data from external storage device ........................................................................128 6.14 Activate Memory Management .............................................................................................131 Commissioning a project ..................................................................................................................... 133 7.1 Overview ...............................................................................................................................133 7.2 Operating modes ..................................................................................................................134 7.3 7.3.1 7.3.2 Using existing projects ..........................................................................................................135 WinCC flexible projects .........................................................................................................135 WinCC projects .....................................................................................................................135 7.4 Data Transmission Options ..................................................................................................136 7.5 7.5.1 7.5.1.1 7.5.1.2 7.5.1.3 7.5.2 7.5.2.1 7.5.2.2 7.5.2.3 7.5.2.4 7.5.2.5 Transfer project to the HMI device ........................................................................................137 Transfer project with WinCC .................................................................................................137 Setting the transfer mode .....................................................................................................137 Starting the transfer ..............................................................................................................139 Testing a project ...................................................................................................................140 Transfer project with WinCC flexible.....................................................................................141 Overview ...............................................................................................................................141 Starting manual transfer........................................................................................................142 Starting automatic transfer ....................................................................................................143 Starting backtransfer .............................................................................................................144 Testing a project ...................................................................................................................145 7.6 7.6.1 7.6.2 Backup and restore ...............................................................................................................147 Overview ...............................................................................................................................147 Backup and restore using ProSave ......................................................................................148 7.7 7.7.1 7.7.2 Updating the operating system .............................................................................................149 Overview ...............................................................................................................................149 Updating the Operating System using ProSave ...................................................................151 7.8 7.8.1 7.8.2 Installing and removing options ............................................................................................152 Overview ...............................................................................................................................152 Installing and removing options using ProSave ....................................................................152 7.9 7.9.1 7.9.2 Transferring and transferring back license keys ...................................................................154 Overview ...............................................................................................................................154 Transfer of license keys with the Automation License Manager ..........................................154 Operating a project ............................................................................................................................. 157 8.1 Overview ...............................................................................................................................157 8.2 Direct keys ............................................................................................................................160 8.3 Setting the project language .................................................................................................161 8.4 8.4.1 8.4.2 8.4.3 Entering values using the touch screen ................................................................................162 Overview ...............................................................................................................................162 Entering and Editing Numerical Values ................................................................................163 Entering and editing alphanumerical values .........................................................................166 MP 277 Operating Instructions, 07/2014, A5E02479740-02 7 Table of contents 9 10 A B 8.4.4 8.4.5 8.4.6 Entering the date and time ................................................................................................... 168 Entering Symbolic Values .................................................................................................... 168 Displaying Infotext ................................................................................................................ 169 8.5 8.5.1 8.5.2 8.5.3 8.5.4 8.5.5 8.5.6 8.5.7 8.5.8 8.5.9 Entering values using the keys ............................................................................................ 170 Control keys ......................................................................................................................... 170 Example: Enter characters using the alphanumeric keyboard ............................................ 173 Function keys ....................................................................................................................... 173 General procedures ............................................................................................................. 174 Entering and editing numerical values ................................................................................. 174 Entering and editing alphanumerical values ........................................................................ 176 Entering the date and time ................................................................................................... 177 Entering Symbolic Values .................................................................................................... 177 Displaying Infotext ................................................................................................................ 178 8.6 Closing the project ............................................................................................................... 179 Maintenance and care..........................................................................................................................181 9.1 Maintenance and care ......................................................................................................... 181 9.2 Clean screen on MP 277 Touch .......................................................................................... 182 9.3 Spare Parts and Repairs ...................................................................................................... 182 9.4 Recycling and disposal ........................................................................................................ 182 Technical specifications .......................................................................................................................183 10.1 10.1.1 10.1.2 10.1.3 10.1.4 Dimension drawings ............................................................................................................. 183 Dimension drawing of the MP 277 8" Touch........................................................................ 183 Dimension drawing of the MP 277 8" Key ........................................................................... 184 Dimension drawing of the MP 277 10" Touch...................................................................... 185 Dimension drawing of the MP 277 10" Key ......................................................................... 186 10.2 10.2.1 10.2.2 Specifications ....................................................................................................................... 186 Specifications of the MP 277 Touch .................................................................................... 186 Specifications of the MP 277 Key ........................................................................................ 188 10.3 Bit assignment of the direct keys ......................................................................................... 189 10.4 10.4.1 10.4.2 10.4.3 10.4.4 Description of the ports ........................................................................................................ 191 Power supply........................................................................................................................ 191 X10/IF 1B (RS 422/RS 485)................................................................................................. 191 X20, X21 (USB).................................................................................................................... 192 X1 (Ethernet/LAN) ................................................................................................................ 192 Appendix .............................................................................................................................................193 A.1 Service and support ............................................................................................................. 193 A.2 System events...................................................................................................................... 193 A.3 ESD guideline ...................................................................................................................... 194 Abbreviations .......................................................................................................................................197 Glossary ..............................................................................................................................................199 Index ...................................................................................................................................................205 MP 277 8 Operating Instructions, 07/2014, A5E02479740-02 1 Overview 1.1 Product overview Possible applications of the MP 277 The Multi Panel MP 277 units are an extension of the 270 series. The HMI devices are based on the innovative standard operating system, Microsoft Windows CE 5.0. The Multi Panel MP 277 units belong to the "Multifunctional Platform" product category. The HMI devices offer enhanced communication options to the office world. The Pocket Internet Explorer is already installed on the HMI devices. The MP 277 offers a variety of application uses, high performance and a favorable cost/performance ratio. The devices are equipped with: PROFIBUS port Ethernet port for connection to PROFINET 2 USB ports TFT screen with up to 64k color Thanks to the wide range of devices, you get to use the device that is suited to you. The HMI devices support the following software options: Sm@rtService Sm@rtAccess /Audit OPC server MP 277 Operating Instructions, 07/2014, A5E02479740-02 9 Overview 1.2 Design of the HMI Device MP 277 8" Touch 1.2 Design of the HMI Device MP 277 8" Touch Front view and side view Recesses for mounting clips Slot for a memory card Display/touch screen Mounting seal Bottom view Recesses for mounting clips Interfaces MP 277 10 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.3 Design of the HMI Device MP 277 8" Key Rear view 1.3 Rating plate Slot for a memory card DIP switch Interface name Fixing elements for strain relief Design of the HMI Device MP 277 8" Key Front view and side view Slot for a memory card Display Recesses for mounting clips Mounting seal MP 277 Operating Instructions, 07/2014, A5E02479740-02 11 Overview 1.3 Design of the HMI Device MP 277 8" Key Bottom view Recesses for a mounting clip Interfaces Rear view Rating plate Slot for a memory card DIP switch Interface name Fixing elements for strain relief MP 277 12 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.4 Design of the HMI Device MP 277 10" Touch 1.4 Design of the HMI Device MP 277 10" Touch Front view and side view Slot for a memory card Display/touch screen Recesses for mounting clips Mounting seal Bottom view Interfaces Recesses for mounting clips MP 277 Operating Instructions, 07/2014, A5E02479740-02 13 Overview 1.5 Design of the HMI Device MP 277 10" Key Rear view 1.5 Rating plate Slot for a memory card DIP switch Interface name Fixing elements for strain relief Design of the HMI Device MP 277 10" Key Front view and side view Slot for a memory card Display Recesses for a mounting clip Mounting seal MP 277 14 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.5 Design of the HMI Device MP 277 10" Key Bottom view Interfaces Recesses for a mounting clip Rear view Rating plate Slot for a memory card DIP switch Interface name Fixing elements for strain relief MP 277 Operating Instructions, 07/2014, A5E02479740-02 15 Overview 1.6 Accessory kit 1.6 Accessory kit The accessory kit contains the following: Mains terminal for the power supply Mounting clips for mounting the HMI device Additional documents may be enclosed with the accessory kit. Mounting clips Spring mounting clips or aluminum mounting clips are provided for mounting the device. The mounting clips hook into oblong holes on the HMI device. The main dimensions of the HMI device are not exceeded by this. Spring mounting clip Aluminum mounting clip Slot Hook Threaded pin Hook A product information with notes on mounting of the HMI device with mounting clips is supplied with the HMI device. The product information is available in the Internet at the following links: Product Information "Spring clamp" (http://support.automation.siemens.com/WW/view/en/34916893) Product Information "Metal mounting clamps" (http://support.automation.siemens.com/WW/view/en/34915725) 1.7 Accessories Accessories are not included in the product package of the HMI device, but can ordered on the Internet at Industry Mall (https://mall.industry.siemens.com). Converter RS 422-RS 232 The converter is required for the connection of controllers of other manufacturers. Connect the RS 422 to RS 232 converter to the RS 422 / RS 485 interface. The converter converts the input signals to RS-232 signals. Order number: 6AV6 671-8XE00-0AX0 MP 277 16 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.8 The HMI device in the operating process PC/PPI cable You need the cable to update the operating system with reset to factory settings. You can also use the cable for data transfer. Connect the PC/PPI cable to the RS 422/RS 485 port. The cable converts the input signals to RS-232 signals. Order number: 6ES7 901-3CB30-0XA0 Note Set a lower bit rate if the connection is lost during the operating system update. If you use a high bit rates, you need to use PC/PPI cable version 3 or higher. The version code is printed on the cable ("E stand 3," for example, corresponds to version 3). 90 elbow adapter If space is limited, you can use an elbow adapter at the RS 422/RS 485 interface. Order number: 6AV6 671-8XD00-0AX0 Clamping frame IP65 degree of protection or enclosure type 4X/type 12 can be achieved with a clamping frame even with little material thickness at the mounting cut-out. For additional information, see Section Preparing for Mounting (Page 38). Clamping frames are available with the following order numbers: Clamping frame for HMI device Order number MP 277 8" Touch 6AV6671-3CS00-0AX0 MP 277 8" Key 6AV6671-3CS01-0AX0 MP 277 10" Touch 6AV6671-8XS00-0AX0 Service pack Content of the service package for all HMI devices: Mounting seals Mounting clips Power supply terminal, 2-pin Order number: 6AV6671-3XA01-0AX1 MP 277 Operating Instructions, 07/2014, A5E02479740-02 17 Overview 1.8 The HMI device in the operating process 1.8 The HMI device in the operating process The HMI device is part of the operating process. The following two phases are key to the way the HMI device is integrated in the operating process: Project design Process management Project design Visualization of the operating process is known as project design. Project design comprises: writing project data saving project data testing project data simulating project data Project design is undertaken independently of the HMI device and results in a project. Once this has been generated, the project can be transferred to the HMI device to control the operating process. Process management Process management is marked by two-way communication between HMI device and controller. This lays the foundations for operator control and monitoring. The operator can intervene in the operating process on the HMI device for control purposes. The controller in turn supplies the results of the operating process which are displayed on the HMI device. MP 277 18 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.9 Functional scope with WinCC and WinCC flexible 1.9 Functional scope with WinCC and WinCC flexible The following tables show the objects that can be integrated in a project for an MP 277. Messages Object Specification Messages Number of discrete alarms WinCC 4000 Number of analog alarms 200 Length of the alarm text 80 characters Number of tags in an alarm Display Max. 8 Alarm line, Alarm window, Alarm view Acknowledge error alarm individually Acknowledge multiple error alarms simultaneously (group acknowledgement) ALARM_S WinCC flexible Yes 16 alarm groups Edit alarm Yes Alarm indicator Yes Display S7 alarms Yes Alarm buffer, retentive Alarm buffer capacity 512 alarms Simultaneously queued alarm events Max. 250 View alarm Yes Delete alarm buffer Yes Print alarm by line Yes Tags, values and lists Object Specification Tags Number 2048 Limit monitoring Input/output Yes Linear scaling Input/output Text lists Number 500 1 Graphics lists Number 400 1 1 WinCC WinCC flexible Yes The maximum total of text and graphics lists is 500. Screens Object Specification Screens Number WinCC 500 Fields per screen Tags per screen Complex objects per screen (for example, bars) Template WinCC flexible 200 500 200 10 Yes MP 277 Operating Instructions, 07/2014, A5E02479740-02 19 Overview 1.9 Functional scope with WinCC and WinCC flexible Recipes Object Specification Recipes Number WinCC 300 Data records per recipe 500 Entries per recipe 1000 Recipe memory 64 KB Storage location 1 WinCC flexible * Memory card 1 * USB memory stick 1 * Network drive The number of recipe data records may be restricted by the capacity of the storage medium. Logs Note The HMI devices are suitable for the logging of relatively small volumes of data. Manage the data in several adjacent archives in a segmented circular log. The use of a large circular log has a negative effect on performance. Object Specification WinCC Logs Number of logs 20 Number of partial logs in a segmented circular log 400 Entries per log 10000 Filing format Storage location 1 WinCC flexible CSV with ANSI character set * Memory card 1 * USB memory stick 1 * Network drive The number of entries in the log may be restricted by the capacity of the storage medium. Safety Object Specification WinCC WinCC flexible Safety Number of user groups 50 Number of users 50 Number of authorizations 32 MP 277 20 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.10 Software options Info texts Object Specification Info texts Length (no. of characters) WinCC WinCC flexible 320 (depending on font) For alarms Yes For screens Yes For screen objects (for example, for I/O field, switch, button, invisible button) Yes Additional functions Object Specification Screen settings Touch screen calibration WinCC 1 Brightness setting Language switching Number of languages VBScript User-specific extension of the functionality Number of scripts 1 1.10 WinCC flexible Yes Yes 16 Yes 50 Graphic objects Vector and pixel graphics Yes Trends Number 300 Scheduler Number of tasks 48 Text objects Number Direct keys PROFIBUS DP direct keys Yes PROFINET IO direct keys Yes 10000 MP 277 Touch only Software options The following software options are available for the MP 277: Sm@rtService The Sm@rtService option enables you to access a remote HMI device from the HMI device or PC via Ethernet. Sm@rtAccess The Sm@rtAccess option enables you to set up communication between different HMI systems. /Audit The /Audit option extends the HMI device to include functions for recording operations in an audit trail and electronic signature. OPC server (OPC XML) The OPC-Server option enables you to create communications to OPC-capable applications from an HMI device or PC via Ethernet. MP 277 Operating Instructions, 07/2014, A5E02479740-02 21 Overview 1.11 Communications 1.11 Communications Number of connections Connection MP 277 Number using a bus connection 6 Number of connections based on "SIMATIC HMI HTTP Protocol" 8 Note In the following cases, you may not enable PROFINET IO in the Control Panel of the HMI device: * Use of PLCs from other manufacturers * Use of SIMATIC 500/505 via NITP PLCs The following table shows the PLCs which can be used with the HMI devices and the protocols or profiles which can be used. PLC Protocol SIMATIC S7 * PPI * MPI1 * PROFIBUS DP * TCP/IP (Ethernet) SIMATIC S5 * PROFIBUS DP Yes SIMATIC 500/505 * NITP Yes * PROFIBUS DP SIMATIC HMI HTTP Protocol * HTTP/HTTPS (Ethernet) Allen-Bradley PLC series SLC500, SLC501, SLC502, SLC503, SLC504, SLC505, MicroLogix and PLC5/11, PLC5/20, PLC5/30, PLC5/40, PLC5/60, PLC5/80 GE Fanuc Automation Yes * DF1 2, 5 * DH+ via KF2 module 3 * DH485 via KF3 module 4 * DH485 4 PLC series 90-30, 90-70, VersaMax Micro * LG Industrial Systems (Lucky Goldstar) / IMO MP 277 Yes Yes SNP PLC series GLOFA GM (GM4, GM6 and GM7) / Series G4, G6 and G7 * Yes Yes Dedicated communication MP 277 22 Operating Instructions, 07/2014, A5E02479740-02 Overview 1.11 Communications PLC Protocol Mitsubishi Electric PLC series MELSEC FX and MELSEC FX0 * Mitsubishi Electric OMRON Modicon (Schneider Automation) Yes Protocol 4 PLC series SYSMAC C, SYSMAC CV, SYSMAC CS1, SYSMAC alpha and CP * Yes FX PLC series MELSEC FX0, FX1n, FX2n, AnA, AnN, AnS, AnU, QnA and QnAS * MP 277 Yes Hostlink/Multilink (SYSMAC Way) PLC series Modicon 984, TSX Quantum and TSX Compact Yes * Modbus RTU 5 PLC series Quantum, Momentum, Premium and Micro PLC series Compact and 984 via Ethernet bridge * 1 2 3 4 5 Modbus TCP/IP (Ethernet) Not possible when connected to S7-212. Applies to controllers SLC503, SLC504, SLC505, PLC5, MicroLogix Applies to controllers SLC504, PLC5 over DF1 Applies to controllers SLC500 to SLC 505 and MicroLogix Only with converter RS 422-RS 232 6AV6 671-8XE00-0AX0 (option) MP 277 Operating Instructions, 07/2014, A5E02479740-02 23 Overview 1.11 Communications MP 277 24 Operating Instructions, 07/2014, A5E02479740-02 Safety instructions and approvals 2.1 2 Safety Instructions Working on the control cabinet WARNING Open equipment The HMI device is open equipment. This means that the HMI device may only be mounted in housings or cabinets, whereby the device can be operated from the front panel. The cubicle or cabinet in which the HMI device is installed may only be accessed with a key or tool and only by trained, authorized personnel. Dangerous voltage Opening the cabinet will expose high voltage parts. Contact with these parts could be fatal. Disconnect the cabinet from the mains before opening it. Potentially explosive atmospheres When operating the HMI device in hazardous areas the following warning applies. WARNING Explosion Hazard Do not disconnect while circuit is live unless area is known to be non-hazardous. Substitution of components may impair suitability for Class I, Division 2 or Zone 2. ATTENTION RISQUE D'EXPLOSION NE PAS DEBRANCHER TANT OUE LE CIRCUIT EST SOUS TENSION, A MOINS QU`IL NE S`AGISSE D'UN EMPLACEMENT NON DANGEREUX. WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2. MP 277 Operating Instructions, 07/2014, A5E02479740-02 25 Safety instructions and approvals 2.1 Safety Instructions ATTENTION RISOUE D'EXPLOSION LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, OIVISION 2. High frequency radiation Note Unintentional operating situations High frequency radiation, for example, from cellular phones, can trigger unwanted operating states. Installation as intended WARNING Installation only in machinery that conforms to the machinery directive It is not allowed to commission the HMI device unless it has been verified that the machine in which the HMI device is to be installed complies with Directive 2006/42/EC. Industrial Security Siemens offers products and solutions with Industrial Security functions that support the safe operation of equipment, solutions, machines, devices and/or networks. They are important components in a comprehensive Industrial Security concept. As a result the products and solutions from Siemens are constantly evolving. Siemens recommends obtaining regular information regarding product updates. For safe operation of Siemens products and solutions appropriate protective measures (e.g., cell protection concept) must be taken and each component must be integrated in a comprehensive Industrial Security concept, which corresponds with the current state of technology. The products of other manufacturers need to be taken into consideration if they are also used. You can find addition information on Industrial Security under (http://www.siemens.com/industrialsecurity). Sign up for our product-specific newsletter to receive the latest information on product updates. For more information, see under (http://www.siemens.de/automation/csi_en_WW). MP 277 26 Operating Instructions, 07/2014, A5E02479740-02 Safety instructions and approvals 2.2 Standards, certificates and approvals Disclaimer for third-party software updates This product includes third-party software. Siemens AG only provides a warranty for updates/patches of the third-party software, if these have been distributed as part of a Siemens software update service contract or officially released by Siemens AG. Otherwise, updates/patches are undertaken at your own risk. You can find more information about our Software Update Service offer on the Internet at Software Update Service (http://www.automation.siemens.com/mcms/automation-software/en/software-updateservice/Pages/Default.aspx). Notes on protecting administrator accounts A user with administrator privileges has extensive access and manipulation options in the system. Therefore, ensure there are adequate safeguards for protecting the administrator accounts to prevent unauthorized changes. To do this, use secure passwords and a standard user account for normal operation. Other measures, such as the use of security policies, should be applied as needed. 2.2 Standards, certificates and approvals Approvals Note The following overview shows possible approvals. The HMI device itself is certified as shown on the label on its rear panel. CE approval The HMI device meets the general and safety-related requirements of the EMC Directive (2004/108/EC "Electromagnetic Compatibility") and conforms to the harmonized European standards (EN) for programmable logic controllers published in the official gazettes of the European Union: 94/9/EU "Devices and protection systems for use as prescribed in potentially explosive areas" (Guidelines for Explosion Protection) EC Declaration of Conformity The EC Declarations of Conformity are available to the relevant authorities at the following address: Siemens AG Industry Sector I IA AS FA DH Amb P.O. Box 1963 92209 Amberg Germany MP 277 Operating Instructions, 07/2014, A5E02479740-02 27 Safety instructions and approvals 2.2 Standards, certificates and approvals Ex approval The following standards and approvals are in effect for the HMI devices: EN 61241-0:2006 EN 61241-1:2004 II 3 D Ex tD A22 lP6x T 52 C or T 70 C x ... Temperature value, see EC design examination certificate The KEMA 06ATEX0266 X test number applies to the following HMI devices: 6AV6643-0CB01-1AX2 (8" Touch V2) 6AV6643-0CB01-1AX2 (10" Touch V2) 6AV6643-0DD01-1AX2 (10" Key V2) 6AV6643-0CB01-1AX1 (8" Touch) 6AV6643-0CD01-1AX1 (10" Touch) 6AV6643-0DD01-1AX1 (10" Key) 6AV6643-0CB01-1AX5 (8" Touch, small frame) 6AV6643-0CD01-1AX5 (10" Touch, small frame) The following standards and approvals are in effect for the 10" INOX HMI device: EN 60079-0:2006 EN 60079-15:2005 EN 61241-0:2006 EN 61241-1:2004 II 3 G Ex nA II T4 II 3 D Ex tD A22 lP65 T 70 C The KEMA 08ATEX0063 X test number applies to the following HMI device: 6AV6643-0ED01-2AX0 (10" INOX) The HMI devices meet the requirements of the European Directive 94/9/EG of the European Parliament and the Council on the approximation of the laws of the member states concerning equipment and protective systems intended for use in potentially explosive atmospheres. The table below includes the associated test numbers. Manufacturer site HMI device class Test number Siemens AG Industry Sector Werner-von-Siemens-Strae 50 D-92209 Amberg Multi Panel KEMA 06ATEX0266 X KEMA 08ATEX0063 X MP 277 28 Operating Instructions, 07/2014, A5E02479740-02 Safety instructions and approvals 2.2 Standards, certificates and approvals UL approval Underwriters Laboratories Inc., conforming to UL 508 (Industrial Control Equipment) CSA C22.2 No. 142 (Process Control Equipment) or Underwriters Laboratories Inc., conforming to UL 508 (Industrial Control Equipment) CSA C22.2 No. 142 (Process Control Equipment) ANSI/ISA 12.12.01 (Hazardous Location) CSA-213 (Hazardous Location) Approved for use in Class I, Division 2, Group A, B, C, D or Class I, Zone 2, Group IIC or non-hazardous locations FM approval Factory Mutual Research (FM) conforming to Approval Standard Class Number 3611, 3600, 3810 Approved for use in Class I, Division 2, Group A, B, C, D T4 Class I, Zone 2, Group IIC T4 Marking for Australia The HMI device fulfills the requirements of standard AS/NZS CISPR 16 (Class A). IEC 61131 The HMI device satisfies the requirements and criteria conforming to IEC 61131-2, Programmable Logic Controllers, Part 2: Operating resource requirements and tests. MP 277 Operating Instructions, 07/2014, A5E02479740-02 29 Safety instructions and approvals 2.3 Notes about usage Shipbuilding approvals The following shipbuilding approvals are in effect for the HMI device: ABS BV DNV GL LRS ClassNK 2.3 Notes about usage Industrial applications The HMI device is designed for industrial applications. It conforms to the following standards: Requirements of the emission standard for industrial environments, EN 61000-6-4: 2007 + A1:2011 Requirements for interference immunity EN 61000-6-2:2005 Use in residential areas Note The HMI device is not intended for use in residential areas. Operation of an HMI device in residential areas can have a negative influence on radio/TV reception. If the HMI device is used in a residential area, you must take measures to achieve Limit Class B conforming to EN 55016 for RF interference. Suitable measures for achieving the degree of noise suppression for Limit Class B include, for example: Installation of the HMI device in grounded control cabinets Use of filters in electrical supply lines Individual acceptance is required. MP 277 30 Operating Instructions, 07/2014, A5E02479740-02 Safety instructions and approvals 2.4 Electromagnetic compatibility 2.4 Electromagnetic compatibility Introduction The HMI device fulfills, among other things, the requirements of the EMC law pertaining to the domestic European market. EMC-compatible installation of the HMI device The EMC-compliant installation of the HMI device and the application of interference-proof cable is the basis for interference-free operation. The "Directives for interference-free installation of PLCs" and the "PROFIBUS Networks" manual also apply for the installation of the HMI device. Pulse-shaped disturbance The following table shows the electromagnetic compatibility of modules with regard to pulseshaped interference. The precondition for electromagnetic compatibility is that the HMI device meets the specifications and guidelines for electrical installation. Pulse-shaped disturbance Tested with Degree of severity Electrostatic discharge in accordance with IEC 61000-4-2 Air discharge: 8 kV Contact discharge: 6 kV 3 Burst pulses (high-speed transient interference) in accordance with IEC 61000-4-4 2 kV power supply cable 2 kV signal cable, > 30 m 1 kV signal cable, < 30 m 3 High-power surge pulses in accordance with IEC 61000-4-5, external protective circuit required (refer to the manual Automation System S7-300, Installation, "Lightning and overvoltage protection" section) Asymmetrical coupling 2 kV power cable DC voltage with protective elements 3 2 kV signal/data cable, > 30 m, with protective elements as required Symmetrical coupling 1 kV power cable DC voltage with protective elements 3 1 KV signal cable, > 30 m, with protective elements as required Pulse-shaped disturbance Magnetic field strength 50/60 Hz, 100 A/m 3 Magnetic fields with power frequencies according to IEC 61000-4-8 MP 277 Operating Instructions, 07/2014, A5E02479740-02 31 Safety instructions and approvals 2.4 Electromagnetic compatibility Sinusoidal interference The following table shows the EMC behavior of the modules with respect to sinusoidal interference. This requires the HMI device to meet the specifications and directives for electrical installation. Sinusoidal interference Test values HF radiation (in electromagnetic fields) in accordance with IEC 61000-4-3 80% amplitude modulation at 1 kHz RF interference current on cables and cable shielding conforming to IEC 61000-4-6 Degree of severity * Up to 10 V/m in the 1 to 2 GHz range * Up to 3 V/m in the 1.4 to 2 GHz range * Up to 3 V/m in the 2 to 2.7 GHz range Test voltage 10 V, with 80% amplitude modulation of 1 kHz in the 10 kHz to 80 MHz range 3 3 Emission of radio interference The following table shows the unwanted emissions from electromagnetic fields in accordance with EN 55011, Limit Value Class A, Group 1, measured at a distance of 10 m. Frequency Interference emission 30 to 230 MHz < 40 dB (V/m) quasi-peak 230 to 1 000 MHz < 47 dB (V/m) quasi-peak 1 to 3 GHz * 66 dB (mV/m) peak * 46 dB (mV/m) average value * 70 dB (mV/m) peak * 50 dB (mV/m) average value 3 to 6 GHz Additional measures If you want to connect an HMI device to the public power supply system, you must ensure Limit Value Class B in accordance with EN 55022. Interference emission for mains AC power supply The following table below shows the interference emission for mains AC power supply. Frequency Interference emission 0.15 to 0.5 MHz * < 79 dB (V) quasi-peak * < 66 dB (V) average value * < 73 dB (V) quasi-peak * < 60 dB (V) average value 0.5 to 30 MHz MP 277 32 Operating Instructions, 07/2014, A5E02479740-02 Safety instructions and approvals 2.5 Transport and storage conditions 2.5 Transport and storage conditions Mechanical and climatic conditions for transportation and storage This HMI device meets the requirements for IEC 61131-2 relating to transportation and storage conditions. The following specifications apply to the transportation and storage of an HMI device in its original packaging. The climatic conditions conform to the following standards: IEC 60721-3-3, Class 3K7 for storage IEC 60721-3-2, Class 2K4 for transport The mechanical conditions correspond to IEC 60721-3-2, Class 2M2. Type of condition Permitted range Drop test (in transport package) 1m Temperature From -20 to +60 C Atmospheric pressure From 1 140 hPa to 660 hPa, corresponds to an elevation of -1 000 to 3 500 m Relative humidity From 10 to 90%, without condensation Sinusoidal vibration in accordance with IEC 60068-2-6 5 to 9 Hz: 3.5 mm 9 Hz to 500 Hz: 9.8 m/s2 Shock in accordance with IEC 60068-2-29 250 m/s2, 6 ms, 1 000 shocks Note Avoid condensation If the HMI device is subjected to low temperatures or extreme fluctuations in temperature during transportation, moisture could occur on or inside the HMI device. Condensation can occur. This can cause malfunctions. The HMI device must have acquired room temperature before it is put into operation. Do not expose the HMI device to direct radiation from a heater in order to warm it up. If there is condensation, wait approximately 4 hours until the HMI device has dried completely before switching it on. Proper transport and storage, installation and assembly as well as careful operation and maintenance are required to ensure trouble-free and safe operation of the HMI device. The warranty for the HMI device will be deemed void if these stipulations are not heeded. MP 277 Operating Instructions, 07/2014, A5E02479740-02 33 Safety instructions and approvals 2.5 Transport and storage conditions MP 277 34 Operating Instructions, 07/2014, A5E02479740-02 3 Planning application 3.1 Notes about usage Mechanical and climatic conditions of use The HMI device is designed for use in a location protected from the effects of the weather. The conditions of use meet the requirements for DIN IEC 60721-3-3: Class 3M3 (mechanical requirements) Class 3K3 (climatic requirements) Use with additional measures The HMI device should not be used at the following locations unless additional measures are taken: In locations with a high degree of ionizing radiation In locations with severe operating conditions, for example, due to: - Corrosive vapors, gases, oils or chemicals - Electrical or magnetic fields of high intensity In plants that require special monitoring, for example: - Elevators - Systems in especially hazardous rooms Mechanical environmental conditions The mechanical environmental conditions for the HMI device are specified in the following table in terms of sinusoidal vibration. Frequency range Constant Occasional 10 Hz f 58 Hz Amplitude 0.0375 mm Amplitude 0.075 mm 58 Hz f 150 Hz Constant acceleration 0.5 g Constant acceleration 1 g Reducing vibrations If the HMI device is subjected to greater shocks or vibrations, you must take appropriate measures to reduce acceleration or amplitudes. We recommend mounting the HMI device on damping materials (on rubber-metal vibration dampers, for example). MP 277 Operating Instructions, 07/2014, A5E02479740-02 35 Planning application 3.1 Notes about usage Testing mechanical environmental conditions The following table provides information on the type and scope of tests for mechanical environmental conditions. Test for Test standard Comments Vibrations Vibration test in accordance with IEC 60068, part 2-6 (sinusoidal) Type of vibration: Transitional rate of the frequency: 1 octave/minute. 10 Hz f 58 Hz, constant amplitude of 0.075 mm 58 Hz f 150 Hz, constant acceleration 1 g Vibration duration: 10 frequency cycles per axis at each of the three associated vertical axes Shock Shock test in accordance with IEC 60068, Part 2 -29 Type of shock: Half-sine Shock intensity: Peak value 15 g, duration 11 ms Direction of impact: 3 shocks in direction at each one of the three associated vertical axes Climatic environmental conditions The following table shows the climatic conditions for operation of the HMI device. Environmental conditions Permitted range Comments Temperature See the "Mounting positions and type of fixation" section * Vertical mounting From 0 to 50 C * Mounting at an angle From 0 to 40 C Relative humidity 10 to 90%, without condensation Atmospheric pressure 1 140 to 795 hPa Corresponds to an elevation of -1 000 to 2 000 m Pollutant concentration SO2: < 0.5 ppm; Relative humidity < 60%, no condensation Test: 10 cm3/m3; 10 days H2S: < 0.1 ppm; Relative humidity < 60%, no condensation Test: 1 cm3/m3; 10 days MP 277 36 Operating Instructions, 07/2014, A5E02479740-02 Planning application 3.2 Mounting positions 3.2 Mounting positions Mounting position The HMI device is suitable for installation in: Mounting cabinets Control cabinets Switchboards Consoles In the following, all of these mounting options are referred to by the general term "cabinet". The HMI device is self-ventilated and approved for vertical and inclined mounting in stationary cabinets. Mounting position Deviation from the vertical Inclined 35 Vertical 0 NOTICE Damage due to overheating Convection through the HMI device is reduced with installation at an angle.This fact also reduces the maximum permitted operating temperature for operation. With sufficient forced ventilation, you can operate the HMI device at an inclined mounting position up to the permitted ambient temperature for vertical installation. Otherwise the HMI device may be damaged and the approvals and warranty may become obsolete. MP 277 Operating Instructions, 07/2014, A5E02479740-02 37 Planning application 3.3 Preparing for Mounting 3.3 Preparing for Mounting Select the mounting location of the HMI device Points to observe when selecting the mounting location: Position the HMI device so that it is not subjected to direct sunlight. Position the HMI device such that it is ergonomically accessible for the user. Choose a suitable mounting height. Ensure that the air vents of the HMI device are not covered as a result of the mounting. Observe the permissible mounting positions for the HMI device. Note Stability of the mounting cut-out The material in the area of the mounting cut-out must provide sufficient strength to guarantee enduring and safe mounting of the HMI device. The force of the mounting clips or operation of the device may not lead to deformation of the material in order to achieve the degrees of protection described below. The material thickness at the mounting cut-out must be at least 1.0 mm. Degrees of protection The protection ratings are only ensured if the mounting cutout conforms to the following: Permitted deviation from plane at the mounting cutout: 0.5 mm This condition must be fulfilled for the mounted HMI device. Permissible surface roughness in the area of the seal: 120 m (Rz 120) With IP65 degree of protection or for enclosure type 4X/type 12 (indoor use only), the material thickness at the mounting cut-out can be a maximum of 6 mm. Spring mounting clips or aluminum mounting clips, each with or without clamping frames, are used depending on the material thickness at the mounting cut-out. The relationships are shown in the table below: Material thickness Spring mounting clips Aluminum mounting clips Clamping frame required 1.0 mm to 1.5 mm x x Yes 1.5 to 2 mm x - No - x Yes 2 to 4 mm x - No 4 to 6 mm - x No The clamping frame is available as an accessory, see section Accessories (Page 16). MP 277 38 Operating Instructions, 07/2014, A5E02479740-02 Planning application 3.3 Preparing for Mounting Dimensions of the mounting cut-out The following table shows the dimensions of the required mounting cut-out: Mounting cut-out MP 277 8" Touch MP 277 8" Key MP 277 10" Touch MP 277 10" Key Width 226+1 338+1 310+1 mm 434 +1 mm Height 166+1 mm 206 +1 mm 248+1 mm 291+1 mm Depth 61 mm 61 mm 61 mm 60 mm mm mm Mounting compatibility The mounting cut-outs of the Multi Panels are compatible with the mounting cut-outs of the following SIMATIC HMI devices: Multi Panel mounting cut-out Compatible to the mounting cut-outs of the HMI device MP 277 10" Touch Thin Client 10" Touch MP 270B 10" Touch MP 277 10" Key KTP1000 Basic MP 277 INOX 10" Touch TP 270 10" MP 377 12" Touch MP 270B 10" Key OP 270 10" Maintaining clearances The HMI device must be installed with the following clearances: Always allow 50 mm above and below the mounting cutout respectively for ventilation Right and left of the mounting cutout respectively for attaching the mounting clips: - When using a clamping frame: 25 mm each - Without clamping frame, with spring mounting clips: 25 mm each - Without clamping frame, with aluminum mounting clips: 15 mm each At least 10 mm behind the rear panel of the HMI device Note Ensure that the maximum ambient temperature is not exceeded when mounting the device in a cabinet and especially in a closed enclosure. MP 277 Operating Instructions, 07/2014, A5E02479740-02 39 Planning application 3.4 Specifications for Insulation Tests, Protection Class and Degree of Protection 3.4 Specifications for Insulation Tests, Protection Class and Degree of Protection Test voltages Insulation stability is demonstrated in the type test with the following test voltages in accordance with IEC 61131-2: Circuits with a nominal voltage of Ue to other circuits or ground Test voltage < 50 V 500 V DC Protection class Protection Class I in accordance with IEC 60536, i.e. protective conductor connection to profile rail required. Protection against foreign objects and water Degree of protection in accordance with IEC 60529 Explanation Front When mounted: Rear panel * IP65 * Enclosure Type 4X/Type 12 (indoor use only) IP20 Touch protection test with standard test probes. There is no protection against ingress by water. The degree of protection provided by the front side can only be guaranteed when the mounting seal lies completely against the mounting cut-out. 3.5 Rated voltages The following table shows the rated voltage and the corresponding tolerance range. Nominal voltage Tolerance range +24 VDC 20.4 V to 28.8 V (-15 %, +20 %) MP 277 40 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.1 4 Checking the package contents Check the package contents for visible signs of transport damage and for completeness. Note Damaged parts A damaged part will cause the HMI device to malfunction. Do not install parts damaged during shipment. In the case of damaged parts, contact your Siemens representative. The following is supplied along with the HMI device: HMI device Accessory kit with mounting clips and mains terminal Additional documents may be included in the product package of all HMI devices. The documentation belongs to the HMI device and is required for subsequent commissioning. Retain all enclosed documentation for the entire service life of the HMI device. You must pass on the enclosed documentation to any subsequent owner or user of the HMI device. Make sure that every supplement to the documentation that you receive is stored together with the operating instructions. 4.2 Mounting the HMI Device Requirement All packaging components and protective foils should be removed from the HMI device. To install the HMI device, you need the mounting clips from the accessories. The mounting seal must be fitted on the HMI device. If the mounting seal is damaged, order a replacement seal. The mounting seal is part of the associated service pack. Mounting Note Always mount the HMI device according to the instructions in this manual. MP 277 Operating Instructions, 07/2014, A5E02479740-02 41 Installing and connecting the device 4.2 Mounting the HMI Device Proceed as follows: 1. Check that the mounting seal is fitted on the HMI device. Do not install the mounting seal turned inside out. This may cause leaks in the mounting cut-out. 2. Insert the HMI device into the mounting cutout from the front. 3. Insert a mounting clip into a recess on the HMI device. 4. Fasten the mounting clip as described in the enclosed product information. The product information on spring mounting clips or aluminum mounting clips is available on the Internet at the following link: - Product Information "Spring clamp" (http://support.automation.siemens.com/WW/view/en/34916893) - Product Information "Metal mounting clamps" (http://support.automation.siemens.com/WW/view/en/34915725) 5. Repeat steps 3 and 4 for all mounting clips that are required for the installation of the HMI device. Note Check the fit of the mounting seal on the front. The mounting seal must not protrude from the HMI device. Otherwise, repeat steps 1 to 5. Positions of mounting clips on the MP 277 8" Touch You will need 10 mounting clips in total. The following figure shows the positions of the mounting clips. MP 277 42 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.2 Mounting the HMI Device Positions of mounting clips on the MP 277 10" Touch You will need 12 mounting clips in total. The following figure shows the positions of the mounting clips. Positions of the mounting clips on the MP 277 8" Key You will need 14 mounting clips in total. The following figure shows the positions of the mounting clips. MP 277 Operating Instructions, 07/2014, A5E02479740-02 43 Installing and connecting the device 4.3 Connecting the HMI device Positions of the mounting clips on the MP 277 10" Key You will need 10 mounting clips in total. The following figure shows the positions of the mounting clips. 4.3 Connecting the HMI device 4.3.1 Overview Requirement The HMI device must be mounted according to the specifications of these operating instructions. Always use shielded standard cables. Additional information is available in the catalog and online order system at Industry Mall (https://mall.industry.siemens.com). MP 277 44 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device Connection sequence Note Damage to the HMI device If you do not keep to the connection sequence you could damage the HMI device. Ensure you connect the HMI device in the sequence described above. 1. Equipotential bonding 2. Power supply Perform a power-up test to ensure the power supply is connected with the correct polarity. 3. Controller 4. Configuration PC as necessary 5. I/Os as necessary Disconnect the HMI device by completing the above steps in reverse order. Connecting the cables When connecting the cables, ensure that the contact pins are not bent. Secure the cable connectors by screwing the connector onto the socket. See also Safety Instructions (Page 25) 4.3.2 Ports The following figure shows the interfaces of the MP 277 HMI device. Power supply connector RS 422/RS 485 interface X10 / IF1b Ethernet interface USB ports X20 and X21 See also Power supply (Page 191) X10/IF 1B (RS 422/RS 485) (Page 191) X20, X21 (USB) (Page 192) X1 (Ethernet/LAN) (Page 192) MP 277 Operating Instructions, 07/2014, A5E02479740-02 45 Installing and connecting the device 4.3 Connecting the HMI device 4.3.3 Connecting the equipotential bonding circuit Differences in electrical potential Differences in potential may occur between spatially separated system parts. Such differences in electrical potential can lead to high equalizing currents over the data cables and therefore to the destruction of their interfaces. Equalizing currents can develop if the cable shielding is terminated at both ends and grounded to different parts of the system. Differences in potential can develop when a system is connected to different mains. General requirements of equipotential bonding Differences in electrical potential must be reduced using equipotential bonding to ensure trouble-free operation of the relevant components of the electronic system. The following must therefore be observed when installing the equipotential bonding circuit: The effectiveness of equipotential bonding increases as the impedance of the equipotential bonding conductor decreases or as its cross-section increases. If two plant parts are interconnected by means of shielded data cables and their shielding is bonded at both ends to the grounding/protective conductor, the impedance of the additionally installed equipotential bonding cable must not exceed 10% of the shielding impedance. The cross-section of a selected equipotential bonding conductor must be capable of handling the maximum equalizing current. Experience has shown that equipotential bonding conductors with a minimum cross-section of 16 mm should be fitted between the control cabinets or the ground point of the supporting arm or the stand for PRO HMI devices. Use equipotential bonding conductors made of copper or galvanized steel. Establish a large surface contact between the equipotential bonding conductors and the grounding/protective conductor and protect them from corrosion. Use a suitable cable clip to clamp the shield of the data cable flush to the equipotential bonding rail. Keep the length of cable between the HMI device and the equipotential bonding rail as short as possible. Route the equipotential bonding conductor and data cables in parallel and with minimum clearance between them. MP 277 46 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device Configuration graphic Chassis terminal on the HMI device, example Equipotential bonding conductor cross-section: 4 mm2 Control cabinet Equipotential bonding conductor cross-section: min. 16 mm2 Ground connection Cable clip Equipotential bonding rail Parallel routing of the equipotential bonding conductor and data cable NOTICE Damage to the interface modules possible Cable shielding is not suitable for equipotential bonding. Use only the prescribed equipotential bonding conductors. The equipotential bonding conductor must have a minimum cross-section of 16 mm. The interface modules may otherwise be damaged or destroyed. MP 277 Operating Instructions, 07/2014, A5E02479740-02 47 Installing and connecting the device 4.3 Connecting the HMI device 4.3.4 Connecting the Power Supply Configuration graphic The following figure shows the connection of the HMI device and the power supply. Note when connecting The mains terminal for connecting the power supply is contained in the accessory kit. The mains terminal is designed for cables with a maximum cross-section of 1.5 mm. MP 277 48 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device Connecting the mains terminal Note Damage Do not tighten the screws of the power supply terminal if it is plugged into the HMI device. The pressure from the screwdriver may otherwise damage the HMI device socket. Only connect the wires when the mains terminal is withdrawn. Connect the power supply terminal to the cables of the power supply as shown in the figure above. Ensure that the lines are connected properly to the correct terminals. Refer to the label for the contact pins on the rear of the HMI device. Reverse polarity protection The HMI device is equipped with reverse polarity protection. Connecting the power supply NOTICE Safe electrical isolation Use only 24 VDC power supply units with safe electrical isolation in accordance with IEC 60364-4-41 or HD 384.04.41 (VDE 0100, Part 410), for example, in accordance with the PELV standard. The supply voltage must be within the specified voltage range. Malfunctions in the HMI device may otherwise result. Applies to non-isolated system design: Connect the connection for GND 24 V from the 24 V power supply output to equipotential bonding for uniform reference potential. You should always select a central point of termination. See also Ports (Page 45) MP 277 Operating Instructions, 07/2014, A5E02479740-02 49 Installing and connecting the device 4.3 Connecting the HMI device 4.3.5 Connecting the PLC Configuration graphic The following figure shows the connection of the HMI device and the controller. MP 277 50 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device Note Use only the approved cables to connect a SIMATIC S7 controller. Standard cables are available for the connection. You can find additional information on this on the Internet at Industry Mall (https://mall.industry.siemens.com). Connecting PROFINET Note Use a cross-cable for the PROFINET connection when using a point-to-point connection. Note PROFINET IO If you use PROFINET IO direct keys, the HMI device must be connected with a switch. For detailed instructions regarding the installation of PROFINET networks, please refer to the PROFINET system description manual. Only connect the HMI device to public Ethernet networks using a switch or comparable device. Configuring an RS 422/RS 485 interface A DIP switch for the configuration of the RS 422/RS 485 interface is located on the back of the HMI device. In the factory state, the DIP switch is set for communication with the SIMATIC S7 PLC via RS 485. Note Note the diagrams of DIP switch settings on the rear panel of the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 51 Installing and connecting the device 4.3 Connecting the HMI device The following table shows the DIP switch settings. The send and receive direction is toggled internally by the RTS signal. Communication Switch setting PROFIBUS DP/ MPI/PPI Meaning No RTS on plug, for data transfer between PLC and HMI device (factory state) RTS on pin 4, same as PLC, for example for commissioning RTS on pin 9, same as programming device, for commissioning, for example RS 422/RS 485 RS 422 interface is active. See also Ports (Page 45) Accessories (Page 16) MP 277 52 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device 4.3.6 Connecting a Configuring PC Configuration graphic The following figure shows the connection of the HMI device and the configuration PC. Use a cross-cable for the PROFINET connection when using a point-to-point connection. The interfaces are described in the specifications. For RS 485-RS 232 conversion, you can order the PC/PPI cable from Siemens AG. MP 277 Operating Instructions, 07/2014, A5E02479740-02 53 Installing and connecting the device 4.3 Connecting the HMI device Configuring the PC/PPI cable Use the DIP switches to configure the transfer rate of the PC/PPI cable. Note Set a lower bit rate if the connection is lost during the operating system update. If you use a high bit rates, you need to use PC/PPI cable version 3 or higher. The version code is printed on the cable ("E stand 3," for example, corresponds to version 3). DIP switch LEDs Set the value of the transfer rate with DIP switches 1 to 3 to the same value that is specified in the configuration software. DIP switches 4 to 8 must be set to "0". The following bit rates can be set: Bit rate in kbps DIP switch 1 DIP switch 2 DIP switch 3 115.2 1 1 0 57.6 1 1 1 38.4 0 0 0 19.2 0 0 1 9.6 0 1 0 4.8 0 1 1 2.4 1 0 0 1.2 1 0 1 In the figure, the bit rate is set to 115.2 kbps. MP 277 54 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device Note when connecting Note USB connection sequence Observe the following sequence when connecting by USB: 1. HMI device 2. PC USB host-to-host cable Use only the driver for the USB host-to-host cable that is supplied with the configuration software. Never use the driver supplied with the USB host-to-host cable. Update operating system If there is no serviceable HMI device image on the HMI device, you can only update the operating system by restoring the factory settings. Use the RS 422/RS 485 interface with the PC/PPI cable on the HMI device. Replacing the HMI device If you connect more than one HMI device with the same IP address in succession to a single configuration PC, you need to ping the configuration PC once from the HMI device on each changeover of the HMI device. See also Ports (Page 45) Accessories (Page 16) 4.3.7 Connecting a USB device Note Use only devices approved for connection to the HMI device. Lists of devices approved for connection to HMI devices via the USB port are available on the Internet at the following addresses: * http://support.automation.siemens.com/WW/view/en/19188460 (http://support.automation.siemens.com/WW/view/en/19188460) * http://support.automation.siemens.com/WW/view/en/11376409 (http://support.automation.siemens.com/WW/view/en/11376409) MP 277 Operating Instructions, 07/2014, A5E02479740-02 55 Installing and connecting the device 4.3 Connecting the HMI device Below are examples of devices you can connect to the USB port of the HMI device: Mouse Keyboard Printer Industrial USB Hub 4 USB memory devices Barcode reader Note USB mouse and USB keyboard for commissioning only Connect a USB mouse or USB keyboard only for commissioning and servicing purposes to the USB port. Functional problem with USB port If you connect an external device with a 230 V power supply to the USB port without using an non-insulated installation, you may experience functional problems. Use a non-insulated system design. Rated load of the interface Malfunctions may occur on a USB device that presents an electrical overload on the port. Adhere to the values for the maximum load on the USB port. See also Connecting the Power Supply (Page 48) X20, X21 (USB) (Page 192) MP 277 56 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.3 Connecting the HMI device 4.3.8 Connecting a Printer. Configuration graphic The following figure shows the connection of the HMI device and the printer. Note when connecting Note Use only cables with metal-braided shielding grounded at both ends to connect the HMI device and printer. Use a cross-cable for the Ethernet connection when using a point-to-point connection. Some printers may require the ASCII character set used in the project to also be defined on the printer. You can find the list of current printers and required settings for HMI devices on the Internet (http://support.automation.siemens.com/WW/view/en/11376409). Read the documentation supplied with the printer when connecting it. See also Ports (Page 45) Connecting a USB device (Page 55) MP 277 Operating Instructions, 07/2014, A5E02479740-02 57 Installing and connecting the device 4.4 Switching on and Testing the HMI device 4.4 Switching on and Testing the HMI device Procedure Proceed as follows: 1. Switching on the power supply. The screen lights up after power is switched on. A progress bar is displayed during startup. If the HMI device fails to start, you have probably crossed the wires on the mains terminal. Check the connected wires and change their connection. The Loader opens once the operating system has started. The HMI device automatically switches to "transfer" mode during initial startup under the following conditions: - No project is loaded on the HMI device. - At least one data channel has been configured. During this process the following dialog appears: 2. Press "Cancel" to stop the transfer. MP 277 58 Operating Instructions, 07/2014, A5E02479740-02 Installing and connecting the device 4.5 Securing the cables Result The Loader appears again. Note When restarting the system, a project may already be loaded on the HMI device. The system then skips "Transfer" mode and starts the project. Use the relevant operating element to close the project. Refer to your plant documentation to find any available additional information on this topic. Function test Perform a function test following commissioning. The HMI device is fully functional when one of the following states is indicated: The "Transfer" dialog is displayed. The loader is displayed. A project is started. Shutting down the HMI device Terminate the project at the HMI device before switching it off. You have the following options for switching off the HMI device: Switch off the power supply. Remove the mains terminal from the HMI device. 4.5 Securing the cables After the power-on test, to ensure strain relief, use cable ties to secure the connected cables to the marked fixing elements. MP 277 Operating Instructions, 07/2014, A5E02479740-02 59 Installing and connecting the device 4.5 Securing the cables MP 277 60 Operating Instructions, 07/2014, A5E02479740-02 Operator controls and displays 5.1 5 Front operator controls MP 277 Touch Display with touch screen The assignment of the operator controls for the MP 277 8" Touch and the MP 277 10" Touch is basically the same. You can operate the MP 277 Touch using the touch screen. All operating elements required for operation are displayed on the display once the HMI device has been started. MP 277 Operating Instructions, 07/2014, A5E02479740-02 61 Operator controls and displays 5.1 Front operator controls MP 277 Key Function keys with LED Display Function keys without LED System keys - alphanumeric keys System keys - control keys System keys - cursor keys The assignment of the operator controls for the MP 277 8" Key and the MP 277 10" Key is basically the same. The MP 277 Key is operated using the system keys and the function keys. The function assigned to a specific function key is defined during configuration. The function keys have no function prior to the project being opened. Note Unintentional action possible Do not carry out several operations simultaneously. You may otherwise trigger unintentional actions. * With touch control: Always touch only one operating element on the screen. * With key control: Do not press more than two keys simultaneously. Note Risk of damage to the touch screen Do not touch the touch screen with pointed or hard objects. Avoid applying excessive pressure to the touch screen with hard objects. Both will substantially reduce the service life of the touch screen and can even lead to total failure. Always operate the touch screen of the HMI device with your fingers or with a touch pen. Damage to the keyboard Use only your fingers to operate the keys of your HMI device. Using hard instruments to press the keys considerably reduces the service life of the key mechanism. MP 277 62 Operating Instructions, 07/2014, A5E02479740-02 Operator controls and displays 5.2 Using Memory Cards with the HMI Device See also Design of the HMI Device MP 277 8" Touch (Page 10) Design of the HMI Device MP 277 8" Key (Page 11) Design of the HMI Device MP 277 10" Touch (Page 13) Design of the HMI Device MP 277 10" Key (Page 14) 5.2 Using Memory Cards with the HMI Device Introduction The following can be saved to the memory card of the HMI device: HMI device image (backup) Logs Recipes Operating system Applications Additional specifications The memory card can be inserted and removed during operation. Do not remove the memory card while data is being accessed by an application, for example during backup or recipe transfer. Note Multimedia card The multimedia card of the SIMATIC S7 controller is not compatible with the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 63 Operator controls and displays 5.2 Using Memory Cards with the HMI Device Procedure - inserting a memory card Proceed as follows: Insert the memory card into the memory card slot. Memory card Memory card slot When inserting the memory card, please note that it can only be inserted as shown in the diagram. When the memory card is correctly inserted into the slot, it stands approx. 3 mm proud of the slot. Using a memory card for the first time Note Data loss The first time you use a memory card the HMI device will request that you format the card. Save a backup copy of memory card data to a PC beforehand. Proceed as follows in order to prevent data loss: 1. Cancel the formatting procedure by pressing "ESC". 2. Save a backup copy of vital data to a PC. 3. Format the memory card on the HMI device. 4. Transfer the backup data from the PC to the memory card. You can now transfer the backup data from the memory card to the HMI device. MP 277 64 Operating Instructions, 07/2014, A5E02479740-02 Operator controls and displays 5.3 Labeling the Function Keys at the MP 277 Key Procedure - removing a memory card Note Data loss The data on the memory card may be lost if you attempt to remove it while the HMI device is accessing its data. Do not remove the memory card while data is being accessed. Observe the corresponding alarms on the screen. Proceed as follows: 1. Unplug the memory card from the memory card slot. 2. Store the memory card in a safe place. 5.3 Labeling the Function Keys at the MP 277 Key Introduction You can label the function keys as required for your project. Use the labeling strips for this purpose. Labeling strip templates are available in a Word document on the Internet at the following address: Labeling strips for SIMATIC HMI devices (http://support.automation.siemens.com/WW/view/en/93994525) Note Do not write on the keyboard to label the function keys. Any printable and writable foil can be used as labeling strip. The permitted thickness of the labeling strip is 0.13 mm. Paper labeling strips are inappropriate. You can use transparent foil, the keyboard membrane of the HMI device is printed on the reverse side. Use transparent foil so that the LEDs of the function keys can be seen. MP 277 Operating Instructions, 07/2014, A5E02479740-02 65 Operator controls and displays 5.3 Labeling the Function Keys at the MP 277 Key Dimensions of the labeling strip for the MP 277 8" Key Dimensions of the labeling strip for the MP 277 10" Key MP 277 66 Operating Instructions, 07/2014, A5E02479740-02 Operator controls and displays 5.3 Labeling the Function Keys at the MP 277 Key Procedure Proceed as follows: 1. Edit the template and then it on the foil. Another option is to print blank templates and later label them manually. 2. Apply a fixing spray to the labeling strips. The fixing spray ensures that the text is water resistant and does not smear, and that the printer ink on the keyboard membrane does not run. 3. Cut out the labeling strip. Ensure that the corners are cut according to the diagram shown above as this makes it easier to slide them into the slot. 4. Remove any existing labeling strips. Note Wait for the printed labeling strips to dry before you insert them. 5. Slide the labeling strips into the slot . 6. Slide the labeling strips into the slot up to the stop. The labeling strip will protrude approximately 3 cm out of the slot. The template dimensions for the labeling strips are designed so that the labeling is correctly placed for the function keys. It is not necessary to secure the labeling strip. When mounting the HMI device, ensure that the labeling strips do not become jammed between the mounting cut-out and the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 67 Operator controls and displays 5.3 Labeling the Function Keys at the MP 277 Key MP 277 68 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.1 6 Loader The following figure shows the loader. The loader buttons have the following functions: Press the "Transfer" button to set the HMI device to "Transfer" mode. The transfer mode can only be activated when at least one data channel has been enabled for the transfer. Press the "Start" button to start the project on the HMI device. If you do not perform an operation, the project on the HMI device will automatically start after a delay. MP 277 Operating Instructions, 07/2014, A5E02479740-02 69 Configuring the device 6.1 Loader Press the "Control Panel" button to open the Control Panel of the HMI device. You can change various settings in the Control Panel, for example, the transfer settings. Press the "Taskbar" button to activate the taskbar with opened Windows CE Start menu: "Taskbar" button in the loader Windows CE Start menu Open loader The following options are available to open the loader: The loader appears briefly after starting the HMI device. The loader appears when the project is closed. If configured, use the relevant operating element to close the project. Refer to your plant documentation to find any available additional information on this topic. MP 277 70 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.1 Loader Key operation in the loader The following table shows the key combinations for navigating in the loader. Key combination Function The next or previous entry is selected. - - The selected button is operated. Protection against unauthorized use You can protect the control panel against unauthorized access by using a password. You can also protect the taskbar and the Desktop with the help of SecureMode. If the HMI device is protected, "secure mode" is displayed on the Windows CE desktop. You can find additional information on this in the section "Enabling and disabling SecureMode (Page 74)". The "Transfer" and "Start" buttons can always be used without having to enter a password. Password protection prevents maloperation. This increases the security of the system or equipment because settings for the current project can only be changed after entering the password. NOTICE Loss of data possible If the password is no longer available, you can only cancel password protection by updating the operating system. All data on the HMI device will be deleted when you update the operating system. Back up the HMI device's data. MP 277 Operating Instructions, 07/2014, A5E02479740-02 71 Configuring the device 6.1 Loader Pocket Internet Explorer The Pocket Internet Explorer is installed on the HMI device. Note The Pocket Internet Explorer and the PC version of the Internet Explorer differ in terms of functional range. Internet Explorer for Windows CE has separate proxy settings that are independent of the settings in the control panel of the HMI device. You can find additional information on the Microsoft's website. Key operation in the user interface The following table shows the key combinations for navigating in the user interface. Key combination Function The task bar is activated with the open Windows CE start menu. The next active program is displayed. The Task Manager is opened. MP 277 72 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.1 Loader Key operation in the Explorer The following table shows the key combinations for navigating in the Explorer. Key combination - Function * Toggles the active window. * Toggles between the Windows CE Desktop and the window. Selects the first entry. Selects the last entry. Selects everything, if the left LED of the key - Activates the menu bar. - Changes to the higher level. lights up. Opens the shortcut menu. Displays the properties. See also Switching on and Testing the HMI device (Page 58) Configuring the data channel (Page 109) Changing Password Protection (Page 89) MP 277 Operating Instructions, 07/2014, A5E02479740-02 73 Configuring the device 6.2 Enabling and disabling SecureMode 6.2 Enabling and disabling SecureMode SecureMode prevents unauthorized access to the desktop and the taskbar of the HMI device. In SecureMode, all functions on the desktop and the taskbar of the HMI device are locked. Procedure Enabling SecureMode 1. Assign a password in the Control Panel for the HMI device. 2. If no password has been assigned for the HMI device, double-click the following icon on the desktop. SecureMode is enabled. The text "secure mode" appears on the desktop. Disabling SecureMode 1. If a password is assigned for the HMI device, then delete it. 2. If no password has been assigned for the HMI device, operate the "Taskbar" button once in the Loader. 6.3 Control Panel 6.3.1 Overview Control Panel of the HMI device You can configure the following settings in the Control Panel of the HMI device: Date/time Screen saver Regional settings Transfer settings Network settings Delay time Password MP 277 74 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.3 Control Panel Opening the Control Panel The Control Panel can be opened as follows: In the startup phase Press "Control Panel" to open the HMI device Control Panel in the Loader. In a running project Operate the operating element provided for the respective task, if configured. Alternatively you can open the Control Panel from the Windows CE start menu as follows. For an HMI device with key operation use the following key combination: For an HMI device with touch operation, press the key on the alphanumeric screen keyboard twice: Select "Settings > Control Panel". MP 277 Operating Instructions, 07/2014, A5E02479740-02 75 Configuring the device 6.3 Control Panel 6.3.2 Reference for functions The following table shows the settings in the Control Panel. Symbol Function Backing up data to external storage device (Page 126) Restoring data from external storage device (Page 128) Importing and Deleting Certificates (Page 125) Setting the Date and Time (Page 90) Setting up the screen keyboard (Page 84) Changing General Internet Settings (Page 121) Setting the Proxy Server (Page 122) Changing Privacy Settings (Page 123) Setting the Character Repetition of the Keyboard (Page 85) Setting the Double-click (Page 86) Changing the Network Configuration (Page 116) * IP address * Name server Changing the Logon Data (Page 118) Backing up Registry Information (Page 92) Changing monitor settings (Page 94) Displaying Information about the HMI Device (Page 100) Restarting the HMI Device (Page 99) Calibrate touch screen (Page 87) 1 Activate Memory Management (Page 131) Changing Password Protection (Page 89) Changing the Printer Properties (Page 96) Enabling PROFINET IO (Page 111) MP 277 76 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.3 Control Panel Symbol Function Changing Regional Settings (Page 92) * Number format * Currency * Time format * Date format Changing S7 transfer settings (Page 106) Setting the screen saver (Page 94) * Screen saver * Reducing screen backlighting Displaying System Properties (Page 101) Setting the device name of the HMI device (Page 115) Configuring the data channel (Page 109) Setting the Delay Time (Page 102) Setting the uninterruptible power supply (Page 104) State of uninterruptible power supply (Page 105) Set the volume (Page 97) Changing E-Mail Settings (Page 119) 2 1 2 For MP 277 Touch only Additional tabs may appear in the "WinCC Internet Settings" dialog. This depends on the options that have been enabled for network operation in the project. 6.3.3 Operating the Control Panel 6.3.3.1 Overview The hardware of the HMI device determines which of the following devices are available: Touch screen The operating elements shown in the dialogs are touch-sensitive. Touch objects are basically operated in the same way as mechanical keys. You activate operating elements by touching them with your finger. To double-click them, touch an operating element twice in succession. HMI device keyboard The operating elements shown in the dialogs are selected and operated using the keys of the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 77 Configuring the device 6.3 Control Panel External USB keyboard An external keyboard can be used to operate the Control Panel in exactly the same way as the HMI device keyboard. Use the keys of the external keyboard which correspond to the HMI device keys in the description. External USB mouse The Control Panel can be operated with an external mouse in exactly the same way as with the HMI touch screen. Click the described operating elements with the mouse. 6.3.3.2 Entries using the touch screen The Control Panel is operated with the touch screen of the HMI device. Procedure 1. Close the project. Use the provided operating element. The loader is displayed. 2. Open the Control Panel by pressing the "Control Panel" button. 3. To open the required dialog, double-click its symbol. 4. Change as required by touching the tab. 5. Now make the necessary changes. Touch the respective input object to make entries. - Use the screen keyboard of the HMI device to enter the new values in the text boxes. - Touch a button to operate it. - Touch the selection box to open a drop down list box. Touch the required entry from the drop down list box. - Touch the check box to activate or deactivate a check box. - Touch a radio button to select it. 6. Confirm the selection with the button or abort the entries with the button. The dialog box closes. 7. Close the Control Panel with the button. 8. Start the project by pressing the "Start" button in the Loader. Input with the screen keyboard A screen keyboard is available for data input. The screen keyboard is displayed as soon as you touch a text box. You can also call up the screen keyboard directly from the Control Panel. MP 277 78 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.3 Control Panel Display methods for the screen keyboard You can change the display method for the screen keyboard and fix the position on the screen. Confirm the entry with the button or abort the entry with the key. Either action closes the screen keyboard. Numerical screen keyboard Alphanumerical screen keyboard The alphanumerical screen keyboard has various levels. - Normal level - Shift level Reduced screen keyboard Changing the display of the screen keyboard Key Function Switching between the numerical and alphanumerical keyboard Switching between the normal level and Shift level of the alphanumerical screen keyboard Activation and deactivation of the numerical and alphanumerical keys of the alphanumerical screen keyboard Switching from full display to reduced display Switching from reduced display to full display Closing of reduced display of the screen keyboard MP 277 Operating Instructions, 07/2014, A5E02479740-02 79 Configuring the device 6.3 Control Panel Moving the screen keyboard 1. Touch the following icon: 2. Without lifting your finger, move the screen keyboard on the touch screen. 3. Release the icon when the required position is reached. See also Setting up the screen keyboard (Page 84) Entering and Editing Numerical Values (Page 163) Entering and editing alphanumerical values (Page 166) Front operator controls (Page 61) 6.3.3.3 Input with the Keyboard The Control Panel is operated with the system keys of the HMI device. Procedure 1. Close the project. Use the provided operating element. 2. Open the Control Panel. The loader is displayed. - Select the "Control Panel" button in the loader using the cursor keys. - Press . The Control Panel is opened. 3. Select the symbol of the required dialog with the cursor keys. 4. Press to open the dialog. 5. Change the tab as required. Press until the name of the tab is selected. Now switch to the other tabs using the cursor keys. MP 277 80 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.3 Control Panel 6. Press to return to the input area and make the necessary changes. Select the respective input object by pressing the key to make entries. - Use the system keys of the HMI device to enter the new values in the text boxes. - To operate a button, select the button with the cursor keys and then press - Open the selection lists with the key combination + . . Select the required entry from the selection list using the cursor keys. Confirm the selected entry by pressing - Press . to activate or deactivate a check box. - Select a option button of a group using the cursor keys. 7. Confirm your entries with or discard your entries with . If you have selected an input object, you first have to complete entry. The dialog box closes. 8. Close the Control Panel. Press . This opens the Control Panel menu. - Select the "Close" entry using the cursor keys. - Press . The loader is displayed. 9. Start the project. - Select the "Start" button in the loader using the cursor keys. - Press . The project is started. Control keys The tables below show the control keys used to operate the Control Panel. MP 277 Operating Instructions, 07/2014, A5E02479740-02 81 Configuring the device 6.3 Control Panel Select operating elements Key/Keys - Function Description Tabulator Selects the next/previous operating element in the tab sequence. Cursor keys Selects the next operating element to the left, right, above or below the current screen object. Navigates in the operating element. Using operating elements Key/Keys - - - - Function Description Scroll back Scrolls back a page in a list. Scroll to the beginning Scrolls to the beginning of a list. Scroll forward Scrolls one page forward in a list. Scroll to the end Scrolls to the end of a list. Enter key * Operates a button. * Accepts and ends an entry. * Deletes the characters of a value entry and restores the original value. * Closes the active dialog. Cancel - Delete characters Deletes the character to the right of the current cursor position. - Delete characters Deletes the character to the left of the current cursor position. Open selection list Opens a selection list. Accept value Accepts the selected value in the selection list without closing the list. MP 277 82 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.3 Control Panel Enter key combinations Key Function Purpose Toggle key assignment Toggles the assignment for a key with multiple assignment. * No LED is lit: The number assignment is enabled. Pressing the button once toggles to letter assignment. * An LED is lit: The left or right letter assignment is enabled. Each time the key is pressed, the system toggles between the left letter assignment, the right letter assignment and the number assignment. Toggle between upper-case and lower-case Used in key combinations, for example for entering upper-case letters. Switch to additional key assignment Some of the keys contain a key assignment imprinted blue, for example the "%" character. Used in key combinations for the blue key assignment. General control function Used in key combinations General control function Used in key combinations See also Entering and editing numerical values (Page 174) Entering and editing alphanumerical values (Page 176) Front operator controls (Page 61) MP 277 Operating Instructions, 07/2014, A5E02479740-02 83 Configuring the device 6.4 Changing settings for operation 6.4 Changing settings for operation 6.4.1 Setting up the screen keyboard You set up the layout and the position of the screen keyboard. Requirement You have opened the "Siemens HMI InputPanel - Options" with the "InputPanel" icon. Button for displaying the screen keyboard Button for saving the screen keyboard settings Button for closing the screen keyboard Procedure 1. Display the screen keyboard by pressing the "Open Input Panel" button. 2. By pressing the button, you can switch between the numerical and alphanumerical screen keyboard. 3. Set the position of the screen keyboard by moving the screen keyboard on the screen. 4. Save your settings by pressing the "Save" button. 5. Close the screen keyboard by pressing the "Close Input Panel" button. 6. Close the dialog. The screen keyboard settings have been modified. See also Entries using the touch screen (Page 78) MP 277 84 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.4 Changing settings for operation 6.4.2 Setting the Character Repetition of the Keyboard You can set the character repeat for the keyboard or screen keyboard in the Control Panel. Requirement You have opened the "Keyboard Properties" dialog box with the "Keyboard" icon. Check box for activating the character repeat Slider control and buttons for the delay time before character repeat Slider control and buttons for the rate of the character repeat Test field Procedure 1. Select the "Enable character repeat" check box to enable the character repeat. 2. Use the buttons to set the delay and rate of the character repeat. You can also use the slider control for this. 3. Verify your settings. For HMI devices with touch operation. - Touch the test field. The screen keyboard opens. - Move the screen keyboard as needed. - Touch any character and keep it pressed. - Check the implementation of the character repetition and the rate of the character repetition in the test field. - Correct your setting if necessary. For HMI devices with key operation. - Select the test field. - Press an alphanumeric key and keep the key pressed down. - Check the implementation of the character repetition and the rate of the character repetition in the test field. - Correct your setting if necessary. 4. Confirm your entries. The dialog box closes. The character repeat for the keyboard is now set. MP 277 Operating Instructions, 07/2014, A5E02479740-02 85 Configuring the device 6.4 Changing settings for operation 6.4.3 Setting the Double-click You can start applications in the Control Panel and in Windows CE with a double-click. A double-click corresponds to two brief touches in sequence. In the "Mouse Properties" dialog, make the following adjustments for touch screen operation and operation with external mouse: Interval between two touch contacts on the touch screen Interval between mouse clicks Note If you make this setting with an external mouse on a device with touch screen, you may encounter problems with the touch recognition. Requirement You have opened the "Mouse Properties" dialog using the "Mouse" icon. Pattern Symbol Procedure 1. Double-click on the grid. After one double-click, the pattern is shown in inverse colors. 2. Double-click on the icon. If the double-click is valid, the symbol is displayed as follows: 3. If the symbol remains unchanged, double-click on the pattern again. 4. Confirm your entries. The dialog box closes. The double-click adjustment is completed. MP 277 86 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.4 Changing settings for operation 6.4.4 Calibrate touch screen Depending on the mounting position and viewing angle, parallax may occur on the touch screen. To prevent any operating errors caused by parallax, calibrate the touch screen again in the startup phase or during runtime. Requirement You have opened the "Touch" tab in the "OP Properties" dialog box with the "OP" icon. Button for calibrating the touch screen MP 277 Operating Instructions, 07/2014, A5E02479740-02 87 Configuring the device 6.4 Changing settings for operation Procedure 1. Touch the "Recalibrate" button to open the following dialog: 2. Briefly touch the middle of the calibration crosshairs . The calibration crosshairs is then displayed at four more positions. Touch the middle of the calibration crosshairs for each position. If you do not touch the middle of the calibration crosshairs, the procedure is repeated. Once you have touched the calibration crosshairs for all positions, the following dialog appears: 3. Touch the touch screen within 30 seconds. The new calibration is saved. If you wait longer than 30 seconds, the new calibration is discarded and the original calibration remains in effect. The "OP Properties" dialog , "Touch" tab is displayed again. 4. Close the dialog. The touch screen of the HMI device is recalibrated. MP 277 88 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.5 Changing Password Protection 6.5 Changing Password Protection You can protect the Control Panel and Windows CE taskbar with a password. Pay particular attention to the section "Enabling and disabling SecureMode (Page 74)". Requirement You have opened the "Password Properties" dialog box with the "Password" icon. Password text box Text box for entering the password a second time Note If the password is no longer available, you cannot do the following until you have updated the operating system. * Making changes to the Control Panel * Operating the Windows CE task bar All data on the HMI device will be overwritten when you update the operating system! Procedure Activating password protection 1. Enter a password in the "Password" text box. Note The following characters cannot be used in passwords: * Blank * Special characters * ? . % / \ ' " 2. Repeat the password entry in the "Confirm Password" text box. 3. Confirm your entries. The dialog box closes. You cannot open the Control Panel or Windows CE taskbar without entering a password. MP 277 Operating Instructions, 07/2014, A5E02479740-02 89 Configuring the device 6.6 Changing HMI device settings Deactivating password protection 1. Delete the entries in the "Password" and "Confirm password" text boxes. 2. Confirm your entries. The dialog box closes. Password protection for the Control Panel and Windows CE taskbar is disabled. 6.6 Changing HMI device settings 6.6.1 Setting the Date and Time You can set the date and time on the HMI device. The HMI must be restarted in the following cases: You have changed the time zone setting. You have changed the setting of the "Daylight savings time currently in effect" check box . Requirement You have opened the "Date/Time Properties" dialog using the "Date/Time Properties" icon. Time zone Time Date "Daylight savings" check box Button for applying changes MP 277 90 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings Procedure 1. Select the appropriate time zone for the HMI device in the "Time Zone" selection box. 2. Touch the "Apply" button to confirm your entry. The time of day shown in the "Current Time" field is adjusted correspondingly to the selected time zone. 3. Set the date in the selection box. 4. Set the current time of day in the "Current Time" text box. Note The system does not automatically switch between standard time and daylight saving time. 5. If you want to switch from standard time to daylight saving time, select the "Daylight saving time currently in effect" check box. When you press the "Apply" button, the time is brought forward by one hour. 6. If you want to switch from daylight saving time to standard time, deactivate the "Daylight saving time currently in effect" check box. When you press the "Apply" button, the time is brought back by one hour. 7. Confirm your entries. The dialog box closes. The settings for the date and time of day have now been changed. Synchronizing the date and time with the PLC The date and time of the HMI device can be synchronized with the PLC if this has been configured in the project and the PLC program. You can find more information on this topic in the online help of the configuration software. Note You have to synchronize the date and time when time-controlled responses are triggered in the PLC by the HMI device. See also Restarting the HMI Device (Page 99) MP 277 Operating Instructions, 07/2014, A5E02479740-02 91 Configuring the device 6.6 Changing HMI device settings 6.6.2 Changing Regional Settings In different countries, for example, the date, time and decimal points are displayed differently. You can adjust the display format to meet the requirements of different regions. The country-specific settings apply to the current project. If the project language is changed, the country-specific settings are also changed. Requirement You have opened the "Regional and Language Settings" dialog box with the "Regional Settings" icon. Region selection box Procedure 1. Select the region from the selection box. 2. Change to the "Number", "Currency", "Time" and "Date" tabs and set the selection boxes to the desired settings. 3. Confirm your entries. The dialog box closes. The HMI device's regional settings have been changed. 6.6.3 Backing up Registry Information Backing up registry information and temporary data You can install and uninstall your own programs on the HMI devices under Windows CE. You must save the registry settings after installation or uninstallation. You can save the following data to the flash memory: Registry information Temporary files MP 277 92 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings Restoring file system from a memory card If memory cards are used, the file system on the memory card may become damaged, perhaps due to a power failure. The HMI device detects the defective file system on start-up or when the memory card is inserted. The HMI device can restore the file system automatically or on request. Requirement You have opened the "Persistent Storage" tab in the "OP Properties" dialog box with the "OP" icon. Button for saving registry information Meaning of the text in the dialog: Saves the current registry information to the flash memory. The HMI device loads the saved registry information the next time it boots. Button for saving temporary files Meaning of the text in the dialog: Saves all the files in temporary storage to the flash memory (for example, from the "Program Files" directory). These files are written back when the HMI device is started. The "\Temp" directory is not saved. Check box for automatically restoring the file system on the memory card when the HMI device starts up and when a memory card is inserted. Procedure 1. Select the "Save Registry" button to save the current registry settings. 2. Select the "Save Files" button to save temporary files. 3. Specify how the file system on the memory card should be restored. - Activate the check box "Automatically Repair ..." to activate automatic restore. - Deactivate the check box "Automatically Repair ..." if you wish to have the files system restored only upon prompting. 4. Confirm your entries. The dialog box closes. The HMI device uses the saved registry information the next time it starts. The temporary files are copied back. MP 277 Operating Instructions, 07/2014, A5E02479740-02 93 Configuring the device 6.6 Changing HMI device settings 6.6.4 Changing monitor settings Requirement You have opened the "Display" tab in the "OP Properties" dialog using the "OP" icon. Procedure 1. If you want to increase the brightness, press the "UP" button. 2. If you want to decrease the brightness, press the "DOWN" button. 3. Confirm your entries. The dialog box closes. The screen settings have been changed. 6.6.5 Setting the screen saver You can set the following time intervals on the HMI device: For the automatic activation of the screen saver For the automatic reduction in the screen's backlighting When you do not undertake an operation within the configured interval, the configured function will be activated automatically. The screen saver and the reduced screen backlighting functions are switched back off by means of the following actions: By pressing any key By touching the touch screen MP 277 94 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings The function associated to the key or button will not be executed by this. Note Deterioration of the backlight brightness The brightness of the backlighting decreases incrementally during its operational life. In order to increase the operational lifetime of the backlighting, activate the backlighting reduction. Burn-in effects The prolonged display of screen contents can occasionally lead to a burn-in effect in the background. This burn-in effect automatically disappears after a certain amount of time, for example, after the screensaver was activated. The longer the same content is displayed on the screen, the longer it will take for the burn-in effect to disappear. Generally, you should always activate the screen saver. When the screen saver is active, the backlighting is reduced at the same time. Requirement You have opened the "ScreenSaver" dialog box with the "ScreenSaver" icon. Time interval in minutes until backlighting is reduced Period of time in minutes before the screen saver is activated Screen saver setting Procedure 1. Enter the interval in minutes after which the backlighting is to be reduced. Entering "0" will deactivate the backlighting reduction. 2. Enter the number of minutes before the screen saver is to be activated. The minimum time is 5 minutes and the maximum time is 71582 minutes. Entering "0" disables the screen saver. MP 277 Operating Instructions, 07/2014, A5E02479740-02 95 Configuring the device 6.6 Changing HMI device settings 3. Select either the standard screen saver or an empty screen. - In order to select the standard screen saver, activate the "Standard" option. - In order to select an empty screen as screen saver, activate the "Blank Screen" option. 4. Confirm your entries. The dialog box closes. The screen saver and the reduced backlighting for the HMI device is set. 6.6.6 Changing the Printer Properties HMI devices can print on local printers or network printers. You can print hardcopy and logs on network printers. Line printing of alarms is not possible on a network printer. You can find the list of current printers and required settings for HMI devices on the Internet at Printers approved for SIMATIC Panels and Multi Panels (http://support.automation.siemens.com/WW/view/en/11376409). Requirement You have opened the "Printer Properties" dialog box with the "Printer" icon. Printer selection box Interface Network address of the printer Paper size selection box Orientation setting Print quality setting MP 277 96 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings Procedure 1. Select the printer in the "Printer Language" selection box. 2. Select the port for the printer in the "Port" selection box. 3. If you wish to print via the network, enter "Network:" in the text box the network address of the printer. 4. Select the paper format in the "Paper Size" selection box. 5. Select the required option button in the "Orientation" group: - "Portrait" for vertical format - "Landscape" for horizontal format 6. Select the print quality. - Select the "Draft Mode" check box if you want to print a draft. - Clear the "Draft Mode" check box if you want to print with higher quality. 7. Set the color mode. - Select the check box "Color" if you wish to print in color. 8. Confirm your entries. The dialog box closes. The settings for the printer have now been changed. 6.6.7 Set the volume You can activate an acoustic feedback for keyboard and touch screen operations. With each touch or activation of a key, an acoustic signal is emitted. Requirement You have opened the "Volume & Sounds Properties" dialog box with the "Volume & Sounds" icon. Check boxes and radio buttons for acoustic feedback when using the keyboard Check boxes and radio buttons for acoustic feedback when using the touch screen Buttons for adjusting the volume MP 277 Operating Instructions, 07/2014, A5E02479740-02 97 Configuring the device 6.6 Changing HMI device settings Note If you deactivate the settings under "Enable sounds for:" no more acoustic signals will be emitted during inadvertent operations. Procedure 1. For HMI devices with keys: - Click the check box "Hardware buttons" to activate the acoustic signal. - Choose between a loud and soft acoustic signal using the "Loud" and "Soft" radio buttons. 2. For HMI devices with touch screen: - Activate the "Screen Taps" check box to activate the acoustic signal. - Choose between a loud and soft acoustic signal using the "Loud" and "Soft" radio buttons. 3. Choose the required volume using the "Loud" and "Soft" radio buttons. 4. Confirm your entries. The dialog box closes. Note The entries in the "Sounds" tab are of no relevance for the HMI device. The properties of the acoustic operation feedback are now set up. See also Overview (Page 157) MP 277 98 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings 6.6.8 Restarting the HMI Device You need to start the HMI device again in the following situations: You have activated or deactivated the PROFINET IO direct keys. You have changed the time zone setting. You have changed the automatic daylight savings and standard setting. NOTICE Data loss when the HMI device is restarted All volatile data is lost when the HMI device is rebooted. Check the following: * The project on the HMI device is not open. * No data is being written to the flash memory. Requirement You have opened the "OP Properties" dialog box by pressing the "OP" icon. Procedure Button for rebooting the HMI device 1. Change to the "Device" tab in the "OP Properties" dialog. 2. Click "Reboot". The following warning is displayed: "If you run this function, all data which has not been backed up will be lost. Close all applications before you restart the device. Reboot?" The HMI device reboots immediately if you confirm this warning. The HMI device reboots. See also Enabling PROFINET IO (Page 111) Setting the Date and Time (Page 90) MP 277 Operating Instructions, 07/2014, A5E02479740-02 99 Configuring the device 6.6 Changing HMI device settings 6.6.9 Displaying Information about the HMI Device You will need the device-specific information when you contact Technical Support. Requirement You have opened the "Device" tab in the "OP Properties" dialog box with the "OP" icon. The figure below shows the dialog using MP 277 8" Touch as an example. HMI device name Version of the HMI device image Version of the boot loader Boot loader release date Size of the internal flash memory in which the HMI device image and project are stored MAC address of the HMI device Button for restarting the HMI device Procedure 1. The device-specific information is displayed in the "Device" tab. 2. Close the dialog when the information is no longer required. Note The size of the internal flash memory does not correspond to the available working memory for a project. MP 277 100 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.6 Changing HMI device settings 6.6.10 Displaying System Properties The system-specific information provides you with information about the processor, operating system and memory of the HMI device. Requirement You have opened the "System Properties" dialog box, "General" tab with the "System" icon. Copyright to Microsoft Windows CE Processor information Size of internal flash memory Procedure Note Do not change the memory distribution in the "Memory" tab. Only applies for the usage of ProSave options according to section "Installing and removing options using ProSave (Page 152)": An alteration to the memory distribution may be necessary. Please refer to the accompanying documentation for further information. MP 277 Operating Instructions, 07/2014, A5E02479740-02 101 Configuring the device 6.7 Setting the Delay Time 1. Change to the "Memory" tab. The memory information is displayed. Size of data storage space Size of program storage space The blue area shows the size of the available memory. 2. If you want to change the size of the assigned storage space, mode the slider. The change is displayed under "Allocated". The slider sets the ratio between data and program storage space. 3. Close the dialog. 6.7 Setting the Delay Time The project is opened following a delay time when the HMI device is switched on. The Loader is displayed during the delay time. Read the description of the "Start" button in the section "Loader (Page 69)" when doing this. Note Do not use the delay time to implement a temporary access protection. MP 277 102 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.7 Setting the Delay Time Requirement You have opened the "Directories" tab in the "Transfer Settings" dialog box with the "Transfer" icon. Directory where the project file is saved Directory where the compressed source file of your project is saved The external memory card or the network connection can be defined as the storage location. During the next backup process, the project's source file is stored in the specified location. Storage location and initialization file of the HMI device for process operation Region selection box NOTICE Settings in "Project File" and "Path" The project may not open at the next start of the HMI device if changes are made here. Do not change the setting in the "Project File" and "Path" fields. Procedure 1. Select the desired delay time in seconds in the "Wait [sec]" selection box. With the value "0", the project starts immediately. It is then no longer possible to call the Loader after switching on the HMI device. If you still wish to access the Loader, an operating element must be configured to close the project. 2. Confirm your entries. The dialog box closes. The delay time for the HMI device is now set. MP 277 Operating Instructions, 07/2014, A5E02479740-02 103 Configuring the device 6.8 Setting the uninterruptible power supply 6.8 Setting the uninterruptible power supply UPS monitoring is an option you load as an add-on with ProSave. A UPS ensures that the HMI device is shut down in a controlled manner after a buffer time in the event of a power failure. This avoids the loss of data. The following uninterruptible power supplies are supported: SITOP DC UPS modules as of a rated power value of 6 A, e.g. 6EP1931-2DC42 Configure the USB port for UPS monitoring. Requirement The UPS is connected to the 24 V input and a USB port. You have opened the "Configuration" tab in the "UPS Properties" dialog box with the "UPS" icon. Text box for the time after which the "Battery mode activated" message is displayed Check box for enabling battery mode Text box for the time after which the "Faulty port" message is displayed Check box for the "Faulty port" message Procedure 1. If you want to enable battery mode, activate the "Battery mode" check box. 2. Enter the time for terminating applications in the "min" and "s" text boxes. You will receive a message when UPS takes effect. Applications such as HMI Runtime and WinAC MP are then terminated depending on the time entered. 3. If the port to which the UPS is connected is faulty and you therefore want to receive a message, activate the "Port disturbed" check box. 4. Select the message you want from the list box. 5. Enter the time after which the "Faulty port" message is displayed in the "min" and "s" text boxes. Port monitoring for the UPS is set. MP 277 104 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.9 State of uninterruptible power supply 6.9 State of uninterruptible power supply If you have connected a UPS to a USB port, you can display the monitoring state of this port. Requirement You have opened the "Current status" tab in the "UPS Properties" dialog using the "UPS" icon. The "UPS program is not running. No current status available." message appears when the UPS is not connected. Update Procedure 1. Installing the UPS monitoring software. 2. Connect the UPS. 3. If you want to update the monitoring state, press the "Update" button. The message is changed according to the current setting. The message will remain unchanged if no check boxes in the "Configuration" tab have been activated. The current monitoring state for the UPS is displayed. MP 277 Operating Instructions, 07/2014, A5E02479740-02 105 Configuring the device 6.10 Change the communication settings 6.10 Change the communication settings 6.10.1 Changing S7 transfer settings The communication settings between the HMI device and PLC are defined in the HMI device project. In the following cases, the communication settings might have to be changed: The first time the project is transferred If changes are made to the project but are only applied later NOTICE Transfer mode using MPI/PROFIBUS DP The changed MP/PROFIBUS DP settings are overwritten in the following cases: * The project is started. * A project is transferred The bus parameters are read from the project currently loaded on the HMI device. You can change the settings for MPI / PROFIBUS DP transfer. The following steps are required: * Close the project. * Change the settings on the HMI device. * Then return to "Transfer" mode. Note * A project can only be transferred from the configuration PC to the HMI device when at least one data channel is activated on the HMI device. * If no DP connection is configured in the project, the data channel is deactivated when the project is started. * If the HMI device is in "Transfer" mode while changes are made to the transfer settings, the settings only go into effect after the transfer function is restarted. MP 277 106 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.10 Change the communication settings Requirement You have opened the "S7-Transfer Settings" dialog box with the "S7-Transfer Settings" icon. Network selection Button for opening the properties dialog Procedure 1. Select a network. - If you have selected "S7 Ethernet", click the "Properties" button to open the "SMC LAN91C111 Ethernet Settings" dialog and proceed as described in the Changing the Network Configuration (Page 116) section to edit the Ethernet settings. - If you have selected "MPI" or "PROFIBUS", proceed as described in the steps below. 2. Open the "MPI" or "PROFIBUS" dialog with the "Properties" button: MP 277 Operating Instructions, 07/2014, A5E02479740-02 107 Configuring the device 6.10 Change the communication settings 3. If more masters are connected to the bus, deactivate the check box "Panel is the only master on the bus". 4. Enter the bus address for the HMI device in the "Address" text box. Note The bus address in the "Address" text box must be unique throughout the MPI/PROFIBUS DP network. 5. Select the transmission rate in the "Transmission Rate" text box. 6. Select the highest station address on the bus in the "Highest Station Address" or "Highest Station" text box. 7. Select the desired profile from the "Profile" selection box. 8. The profile information is displayed when you select "Bus Parameters" button in the PROFIBUS dialog. The "Profile" dialog is read-only. Note The bus parameters must be the same for all stations in the MPI/PROFIBUS DP network. 9. Close the "Profile" dialog. 10. Confirm your entries in the "MPI" or "PROFIBUS" dialog. The dialog box closes. The MPI/PROFIBUS DP settings of the HMI device have been changed. MP 277 108 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.10 Change the communication settings 6.10.2 Configuring the data channel If you block all data channels, the HMI device is protected against unintentional overwriting of the project data and HMI device image. Note A project can only be transferred from the configuration PC to the HMI device when at least one of the data channels is enabled on the HMI device. Requirement You have opened the "Transfer Settings" dialog box with the "Transfer Settings" icon. Group for data channel 1 (Channel 1) Group for data channel 2 (Channel 2) Button for the dialog "S7 Transfer Settings" or "Network and Dial-Up Connections." The "Directories" tab is described in the section "Setting the Delay Time (Page 102)". Note Changes during "Transfer" mode If the change transfer settings during "Transfer" mode, the changed transfer settings will not into effect until the next time you start the transfer. This may occur if the Control Panel is opened to change the transfer properties in an active project. MP 277 Operating Instructions, 07/2014, A5E02479740-02 109 Configuring the device 6.10 Change the communication settings Procedure 1. You can clear the required data channel by activating the associated "Enable Channel" check box in the "Channel 1" or "Channel 2" group. In the "Channel 1" group, the RS-422/RS-485 port is configured for the serial data transfer. - Select the "Enable Channel" check box to enable the data channel. - Clear the "Enable Channel" check box to lock the data channel. Note Only select the "Remote Control" check box in the "Channel 1" group, if serial transfer is in progress. Clear the check box before changing to "Online" mode. 2. Enable automatic transfer by activating the respective "Remote Control" check box in the "Channel 1" or "Channel 2" group. WARNING Unintentional transfer mode If the HMI is accidentally switched to Transfer mode, unintentional actions can be triggered in the plant. Ensure that the configuration PC does not inadvertently switch the HMI device to transfer mode while the project is in runtime. 3. Select the required protocol for "Channel 2" in the selection box. Note Serial transfer mode via channel 2 The bus parameters, for example address of the HMI device, are read out of the project that is currently running on the HMI device. You can change the settings for the transfer via channel 2. The following steps are required: * Close the project. * Change the settings on the HMI device. * Then return to "Transfer" mode. The next time the project is started on the HMI device, the settings will be overwritten by the values from the project. MP 277 110 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.10 Change the communication settings 4. Enter further parameters if required. - Applies to "MPI/Profibus/S7-Ethernet:" Press the "Advanced" button to change to the "S7-Transfer Settings" dialog. There you can change the settings for MPI/PROFIBUS or S7 Ethernet. Confirm your entries. The "S7-Transfer Settings" dialog box closes. - Applies to "ETHERNET": Press the "Advanced" button to change to the "Network&Dial-Up Connections." Open the "LAN9001" entry. You can change the TCP/IP settings there. Confirm your entries. Close "Network&Dial-Up Connections". - Applies to "USB:" No further settings are required for "USB". 5. Confirm your entries. The dialog box closes. The data channel is configured. See also Changing S7 transfer settings (Page 106) Changing the Network Configuration (Page 116) Operating modes (Page 134) 6.10.3 Enabling PROFINET IO If the HMI device is connected to the PLC via PROFINET, function keys or buttons, for example, can be configured as PROFINET IO direct keys. If PROFINET IO direct keys are used in the project, they must be enabled. Note If you enable PROFINET IO direct keys, you cannot use the RS 422/RS 485 port for serial communication. PROFINET IO direct keys and PROFIBUS DP direct keys are mutually exclusive. MP 277 Operating Instructions, 07/2014, A5E02479740-02 111 Configuring the device 6.10 Change the communication settings Requirement You have opened the "PROFINET" dialog box with the "PROFINET" icon. Enabling or disabling the PROFINET IO direct keys Text box for the device name MAC address of the HMI device Note If the device name does not match the device name entered in the HW Config of STEP 7, the direct keys do not work. Use the device name from the HW Config of STEP 7. This device name does not correspond to the device name used under Windows CE. Within the ETHERNET data network, the device name must be unique and satisfy the DNS conventions. These include: Restriction to 127 characters in total (letters, digits, hyphen or point). A name component within the device name, e.g. a string between two points, may not exceed 63 characters. Special characters such as umlauts, brackets, underscores, slashes, spaces etc. are not permitted. The hyphen is the one exception. The device name must not start or end with a the "-" character. The device name must not take the form n.n.n.n (n = 0 to 999). The device name must not start with the character sequence "port-xyz-" (x, y, z = 0 to 9). Procedure 1. If you want to enable the PROFINET IO direct keys, select the "PROFINET IO enabled" check box. 2. Enter the device name of the HMI device. 3. Confirm your entries. The dialog box closes. 4. Reboot the HMI device after saving the settings. The PROFINET IO direct keys are enabled. MP 277 112 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation See also Restarting the HMI Device (Page 99) Overview (Page 157) 6.11 Configuring network operation 6.11.1 Overview of network operation You can connect the HMI device to a PROFINET network via the Ethernet port. The connection to a network offers, for example, the following options: Printing via a network printer The HMI device's operating system does not support line by line alarm logging via a network printer. All other printing functions, for example hardcopy or logs are available without restriction via the network. Saving, exporting and importing of recipe data records on or from a server Setting up of message and data archives Transferring a project Backing up data Note The HMI device can only be used in PROFINET networks. The HMI device only has client functionality in the PC network. This means that users can access files of a node with TCP/IP server functionality from the HMI device via the network. However, you cannot, for example, access data on the HMI device from a PC via the network. Note Information on communication using SIMATIC S7 over PROFINET is provided in the online help of the configuration software. MP 277 Operating Instructions, 07/2014, A5E02479740-02 113 Configuring the device 6.11 Configuring network operation Addressing the computer Within a PROFINET network, computers are usually addressed using computer names. These computer names are translated from a DNS or WINS server to TCP/IP addresses. This is why a DNS or WINS server is needed for addressing via computer names when the HMI device is in a PROFINET network. Such servers are usually present in PROFINET networks. Note The use of TCP/IP addresses to address PCs is not supported by the operating system. For additional questions on addressing in your network, contact your network administrator. Requirement Before beginning the configuration, request the following network parameters from your network administrator. Does the network use DHCP for dynamic assignment of network addresses? If not, get a new TCP/IP network address for the HMI device. Which TCP/IP address does the default gateway have? If a DNS network is used, what are the addresses of the name server? If a WINS network is used, what are the addresses of the name server? General procedure for configuring the network The HMI device must be configured prior to network operation. The configuration is basically divided into the following steps: 1. Enter the computer name of the HMI device. 2. Configure the network address. 3. Set the logon information. 4. Back up the settings. MP 277 114 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 6.11.2 Setting the device name of the HMI device The HMI device uses the device name to identify itself in the network. Requirement You have opened the "System Properties" dialog box with the "System" icon. Device name of the HMI device Description for the HMI device (optional) Note Change the device name for the HMI device in the "Device name" text box to activate the network functions. Procedure 1. Enter the device name for the HMI device in the "Device name" text box. 2. Enter a description for the HMI device in the "Device description" text box. 3. Confirm your entries. The dialog box and the screen keyboard are closed. The device name for the HMI device is now set. See also Overview of network operation (Page 113) MP 277 Operating Instructions, 07/2014, A5E02479740-02 115 Configuring the device 6.11 Configuring network operation 6.11.3 Changing the Network Configuration You can change the network settings for the LAN connection under "Network & Dial-Up Connections". Requirement You have opened the following display using the "Network&Dial-Up Connections" icon. Procedure 1. Open the "LAN90001" entry. The following dialog is displayed. IP address over DHCP Manual IP address 2. Select either automatic address assignment over DHCP or manual address input. 3. If you assign the address manually, enter the required address in the text boxes for "IP Address", "Subnet Mask" and, if used, "Default Gateway". 4. If a name server is used in the network, change to the "Name Servers" tab. Note the FAQ during setting "Integrating an HMI device into a local network (http://support.automation.siemens.com/WW/view/en/13336639)". MP 277 116 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 5. Enter the respective addresses in the text boxes. 6. Change to the "Ethernet Parameters" tab. Selection list with entries for transfer type and transfer speed Refers to network topology You can find information on the MP 277 in the online help of the TIA Portal. 7. In the "Mode and Speed" selection list, select the transfer type and the transfer speed. Take the transfer type and transfer speed of the connected devices in the network into consideration when you make your selection. 8. Confirm your entries. The dialog box closes. 9. Close the "Network&Dial-Up Connections" view. The Control Panel is displayed again. The LAN connection parameters for the HMI device have been changed. See also Overview of network operation (Page 113) MP 277 Operating Instructions, 07/2014, A5E02479740-02 117 Configuring the device 6.11 Configuring network operation 6.11.4 Changing the Logon Data Windows CE uses this information to gain access to the network resources. Enter the user name, password and domain you have received from your administrator. Requirement You have opened the "Network ID" dialog box with the "Network ID" icon. Procedure 1. Enter the user name in the "User name" text box. 2. Enter your password in the "Password" text box. 3. Enter the domain name in the "Domain" text box. 4. Confirm your entries. The dialog box closes. The logon information has now been set. See also Overview of network operation (Page 113) MP 277 118 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 6.11.5 Changing E-Mail Settings Requirement You have opened the "WinCC Internet Settings" dialog box with the "WinCC Internet Settings" icon. Setting the SMTP server Name for the sender E-mail account Button for the "Advanced" dialog Note Additional tabs may appear in the "WinCC Internet Settings" tab. This depends on the options that have been enabled for network operation in the project. Procedure 1. Specify the SMTP server. - Select the "Use the default of the project file" option button if you want to use the SMTP server configured in the project. - Deactivate the "Use the default of the project file" option button if you do not want to use the SMTP server configured in the project. - Specify the required SMTP server. 2. Enter the name for the sender in the "Name of sender" text box. 3. Enter the e-mail account for your e-mail in the "E-mail address of sender" text box. Some e-mail providers only allow you to send mail if you specify the e-mail account. The "E-mail address of sender" text box can remain empty if your e-mail provider allows you to send mail without checking the account. MP 277 Operating Instructions, 07/2014, A5E02479740-02 119 Configuring the device 6.11 Configuring network operation 4. If you want to save the e-mail settings, press the "Advanced" button. The following dialog appears: Default values of the project file Disable authentication Use panel settings for authentication Enter secure connection The following message is displayed when you make changes: Restart the SIMATIC HMI Runtime for the settings to become effective. 5. Confirm your entries. The dialog box closes. The e-mail settings have been changed. See also Overview of network operation (Page 113) MP 277 120 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 6.11.6 Changing internet settings 6.11.6.1 Changing General Internet Settings Requirement You have opened the "General" tab in the "Internet Options" dialog box with the "Internet Options" icon. The dialog is an example. Note Do not change the settings in the "User Agent" field. Procedure 1. Enter the required start page for the browser in the "Start Page" text box. 2. Enter the address of the standard search engine in the "Search Page" text box. 3. Enter the required cache memory size in the "Cache" text box. 4. The cache can be deleted by means of the "Clear Cache" button. 5. The history can be deleted by means of the "Clear History" button. 6. Confirm your entries. The dialog box closes. The general parameters for the Internet browser have been set. See also Overview of network operation (Page 113) MP 277 Operating Instructions, 07/2014, A5E02479740-02 121 Configuring the device 6.11 Configuring network operation 6.11.6.2 Setting the Proxy Server Requirement You have opened the "Connection" tab in the "Internet Options" dialog box with the "Internet Options" icon. Settings for the LAN connection Settings for the Internet connection Button to open the "Advanced Proxy Settings" dialog box Procedure 1. Activate the "Use LAN (no autodial)" check box. 2. If you use a proxy server, activate the "Access the Internet using a proxy server" check box in the network group. Specify the address of the proxy server and the port. Note The proxy settings in the Control Panel apply to all applications that are running on the HMI device. The Pocket Internet Explorer requires independent proxy settings that you must specify in the properties of the Pocket Internet Explorer. You can find additional information on the Microsoft website. 3. If you want to bypass the proxy server for local addresses, activate the "Bypass proxy server for local addresses" check box. MP 277 122 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 4. If you do not want to use specific proxy servers, press the "Advanced" button. The following dialog appears: Proxy server addresses that are to be excluded from the Internet connection 5. Specify the address components of the proxy server you want to exclude. Separate multiple entries with a semicolon. 6. Confirm your entries. The dialog box closes. See also Overview of network operation (Page 113) 6.11.6.3 Changing Privacy Settings Cookies and encryption Cookies are pieces of information sent by a web server to a browser. In the event of subsequent access to the web server, the cookies are sent back. This enables information to be stored between the accesses. In order to ensure a high level of privacy, data are sent via the Internet in encrypted form. Common encryption protocols include SSL and TLS. You can activate or deactivate the usage of encryption protocols. The required settings can be obtained from your network administrator. MP 277 Operating Instructions, 07/2014, A5E02479740-02 123 Configuring the device 6.11 Configuring network operation Requirement You have opened the "Privacy" tab in the "Internet Options" dialog box with the "Internet Options" icon. Procedure 1. Select the required cookie behavior by means of the option buttons. - "Accept" Cookies are stored without request. - "Block" Cookies will not be stored. - "Prompt" Cookies will be stored on request. 2. If you want allow cookies which are restricted to a single session, activate the "Always allow session cookies" checkbox. 3. Change to the "Advanced" tab. Double-click the displayed folder structure to close and open it. 4. Select the required encryption protocols and if a warning is to be displayed when you change from secure to insecure mode. 5. Confirm your entries. The dialog box closes. The logon information has now been set. See also Overview of network operation (Page 113) MP 277 124 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.11 Configuring network operation 6.11.6.4 Importing and Deleting Certificates You can import, view and delete certificates that have been imported for the HMI device. The certificates differ in the following ways: Certificates that you trust Own certificates Other certificates You can import additional certificates and delete certificates that are not required. The required settings can be obtained from your network administrator. Requirement You have opened the "Certificates" dialog box with the "Certificates" icon. Selection box of the certificate types Assigned certificates Procedure 1. Select the type of certificate from the selection box: - "Trusted Authorities" - "My Certificates" - "Other Certificates" 2. If you want to import a certificate, press the "Import" button. The "Import Certificate or Key" dialog box is displayed. 3. Select the storage location. 4. Confirm your entries. The certificate is added. 5. If you want to remove a certificate, select the specific certificate. 6. Click "Remove". The certificate is removed. MP 277 Operating Instructions, 07/2014, A5E02479740-02 125 Configuring the device 6.12 Backing up data to external storage device 7. Press the "View" button to list the properties of the selected certificate. 8. Close the dialog. The changes to the certificates have been undertaken. See also Overview of network operation (Page 113) 6.12 Backing up data to external storage device A backup involves copying the operating system, applications and data from the internal in flash memory of the HMI device to an external storage device. The following external storage devices are possible: External memory USB memory stick Requirement The HMI device features an external storage device with sufficient free space. You have opened the "Backup/Restore" dialog box with the "Backup/Restore" icon. MP 277 126 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.12 Backing up data to external storage device First time use of the memory card Note The first time you use a memory card the HMI device will request that you format the card. Save a backup copy of memory card data to a PC before formatting. 1. Cancel the formatting procedure by pressing "ESC". 2. Remove the memory card from the HMI device. 3. Save a backup copy of vital data to a PC. 4. Insert the memory card into the HMI device. 5. Format the memory card on the HMI device. Procedure 1. Press the "BACKUP" button to open the "Select Storage Card" dialog. The "--- no storage card available ---" message appears if there is no external memory in the HMI device or if this memory is defective. Insert an external memory or a different one. 2. Select the external memory for backup from the "Please select a Storage Card" list box. 3. Click on the "Start Backup" button. The HMI device checks the external memory. If the "This storage card..." message appears, an external memory with a greater memory capacity is needed. Acknowledge this message. Backup is aborted. Insert an external memory with a greater memory capacity and restart the backup process. If the "You may have an old backup on the storage card. Do you want to delete it?" message appears, there is already a backup on the external memory. If you do not want to overwrite the backup, press the "No" button. Otherwise click on the "Yes" button. Several messages are displayed in sequence in the "Backup" dialog box: - Saving registry data - Copy files - Saving CE-Image A progress bar shows the status of the backup process. When the backup process is completed, the following message is displayed: "The operation completed successfully." 4. Acknowledge this message. The dialog box closes. The HMI device data is now saved on the external memory. MP 277 Operating Instructions, 07/2014, A5E02479740-02 127 Configuring the device 6.13 Restoring data from external storage device 6.13 Restoring data from external storage device A restore operation deletes the old data from flash memory of the HMI device on confirmation. The data stored on the external memory is then copied to the internal flash Flash memory. Requirement The external storage device with data backup is inserted in the HMI device. You have opened the "Backup/Restore" dialog with the "Backup/Restore" icon. NOTICE Loss of data possible All data on the HMI device will be deleted during a restore operation. License keys are deleted after a security prompt. Back up existing data before you restore them, if required. Note This applies to the first time use of a storage device - read the section "Using Memory Cards with the HMI Device (Page 63)". MP 277 128 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.13 Restoring data from external storage device Procedure 1. Press the "RESTORE" button to open the "Storage Card" dialog. List of detected storage devices Button to refresh the list of detected storage devices Button to start the Restore process 2. Select the external storage device with the backup in the "Storage Card with Backup detected" selection box. Note If several external storage devices with data backups are plugged in, the data cannot be restored. Remove the external storage device with the data backups not needed. The "--- no storage card available ---" message appears if there is no storage device in the HMI device or if it is defective. 3. If the "--- no storage card available ---" message appears, press the "Cancel" button. Restoring is then aborted. - Insert the storage device or another one. - Click "Refresh". The content of the selection box will be changed. - Select the external storage device with the backup in the "Storage Card with Backup detected" selection box. 4. Click on the "Start Restore" button. Restoring is started. MP 277 Operating Instructions, 07/2014, A5E02479740-02 129 Configuring the device 6.13 Restoring data from external storage device 5. The data to be restored is checked. The following messages are displayed in sequence in the "Restore" dialog: - Starting Restore - Checking data When the data has been checked, the following message is displayed: "You are starting RESTORE now. All files (except files on storage cards) and the registry will be erased. Are you sure?" The message means that the restore process can be started. All files files except those located on the external memory will be deleted. Tab entries are also deleted. Are you sure? 6. If you do not want to allow the data to be deleted from the HMI device, abort the restore process by pressing the "No" button. 7. Start to restore the data by selecting "Yes". The following messages are displayed in sequence during the restore: - Deleting files on flash - Restore CE-Image A progress bar shows the status of the restore process. When restore is completed, the following message is displayed: "Restore of CE Image finished. The device will be rebooted now. Don't remove the storage card." 8. Acknowledge this message. The HMI device reboots. The "Restore" dialog box is displayed after booting. Finally, the following message is displayed: "Restore successfully finished. Press ok, remove your storage card and reboot your device." 9. Remove the storage device with the data backup. 10. Restart the HMI device. The data from the external storage device is now on the HMI device. Note You may have to recalibrate the touch screen after the restore operation. MP 277 130 Operating Instructions, 07/2014, A5E02479740-02 Configuring the device 6.14 Activate Memory Management 6.14 Activate Memory Management If reorganization of the memory is required during the runtime of project, the HMI device can shut down the project autonomously. The project is shut down and the HMI device will display a message. You have to start the project again. Note If you do not activate memory management, undefined states can occur during the runtime of the project. Requirement You have opened the "Memory Monitoring" tab in the "OP Properties" dialog box with the "OP" icon. Maximum memory used since the HMI device was last switched on Currently used memory Check box for selecting memory management Procedure 1. In order to start memory management, activate the control box. 2. Confirm your entries. A message is displayed briefly. The dialog box closes. Memory management is activated. MP 277 Operating Instructions, 07/2014, A5E02479740-02 131 Configuring the device 6.14 Activate Memory Management MP 277 132 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.1 7 Overview Configuration phase A project - the process image of the working process - is produced during configuration to visualize automated working processes. The process displays for the project contain displays for values and messages which provide information about process statuses. The process control phase follows the configuration phase. Process control phase The project must be transferred to the HMI device if it is to be used in process control. Another precondition for process control is that the HMI device is connected online to a controller. Current working processes - operating and observing - can then be subject to process control. Transferring the project to the HMI device You can transfer a project to an HMI device as follows: Transfer from the configuring PC Restore from a PC using ProSave In this case, an archived project is transferred from a PC to the HMI device. The configuration software need not be installed on this PC. Commissioning and recommissioning Initial and re-start-ups differ in the following respects: When the HMI device is commissioned there is no project at first. The HMI device is also in this state after the operating system has been updated. When recommissioning, any project already on the HMI device is replaced. MP 277 Operating Instructions, 07/2014, A5E02479740-02 133 Commissioning a project 7.2 Operating modes 7.2 Operating modes Operating modes The HMI device may be in the following operating modes: Offline Online Transfer "Offline mode" and "Online mode" can be set on both the configuring PC and the HMI device. To set these modes on the HMI device, use a corresponding operating element of the project. Changing the operating mode The configuration engineer must have configured an appropriate operating element to allow a change of the operating mode on the HMI device during ongoing operation. Further information on this may be available in your plant documentation "Offline" operating mode In this mode, there is no communication between the HMI device and PLC. Although the HMI device can be operated, it cannot exchange data with the PLC. "Online" operating mode In this mode, the HMI device and PLC communicate. You can operate the plant on the HMI device according to your system configuration. "Transfer" mode In this mode, you can transfer a project from the configuring PC to the HMI device or backup and restore HMI device data, for example. The following options are available for setting "Transfer" mode on the HMI device: When the HMI device starts up Start "Transfer" mode manually in the HMI device Loader. During ongoing operation Start the "Transfer" mode manually within the project using an operating element. The HMI device toggles to "Transfer" mode when automatic mode is set and a transfer is initiated on the configuring PC. MP 277 134 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.3 Using existing projects 7.3 Using existing projects 7.3.1 WinCC flexible projects The following table shows how you can reuse existing projects, while observing the screen size: 1 HMI device in the existing project New HMI device TP 270 10" MP 277 10" Touch or MP 277 8" Touch OP 270 10" MP 277 10" Key MP 270 6" Touch TP 277 6" 1) MP 270 10" Touch MP 277 10" Touch or MP 277 8" Touch MP 270 10" Key MP 277 10" Key If you have set options on the MP 270 6" Touch, you must use the MP 277 8" Touch as the successor. The following cases are possible: 1. Project exists in ProTool: Migrate the project to WinCC flexible and subsequently carry out an HMI device switch. 2. Project in WinCC flexible exists: Carry out an HMI device switch in WinCC flexible. Further information on the subject can be found in the WinCC flexible Online Help or in the "WinCC flexible Migration" manual. 7.3.2 WinCC projects To use an existing WinCC flexible project in WinCC, migrate the project to WinCC. You can find more information on this topic in the WinCC online help. MP 277 Operating Instructions, 07/2014, A5E02479740-02 135 Commissioning a project 7.4 Data Transmission Options 7.4 Data Transmission Options The following table shows the options for data transfer between the MP 277 and the configuration PC. Type Data channel Backing up Serial 1 MP 277 Yes MPI/PROFIBUS-DP Yes USB Yes Ethernet Restoring Update operating system Transferring a project Installing or removing an option License key transferring or transferring back 1 Serial Yes Yes 1 MPI/PROFIBUS-DP Yes USB Yes Ethernet Yes Serial, with reset to factory settings 1 Yes Serial 1 Yes MPI/PROFIBUS-DP Yes USB Yes Ethernet Yes Serial Yes 1 MPI/PROFIBUS-DP Yes USB Yes Ethernet Yes Serial Yes 1 MPI/PROFIBUS-DP Yes USB Yes Ethernet Yes Serial Yes 1 MPI/PROFIBUS-DP Yes USB Yes Ethernet Yes Applies when PC/PPI cable is used MP 277 136 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.5 Transfer project to the HMI device 7.5 Transfer project to the HMI device 7.5.1 Transfer project with WinCC 7.5.1.1 Setting the transfer mode Introduction You can start the "Transfer" mode manually or automatically on the HMI device. If the automatic transfer is enabled, the HMI device automatically switches to "Transfer" mode when the following event occurs during runtime: You start project transfer on the connected configuration PC. Note With automatic transfer, the HMI device only switches to "Transfer" mode when the project is running on the HMI device. Automatic transfer is particularly suited for the test phase of a new project because the transfer is completed without interfering with the HMI device. Note If automatic transfer is activated on the HMI device and a transfer is initiated on the configuration PC, the project currently running is automatically stopped. The HMI device then automatically switches to "Transfer" mode. After the commissioning phase, deactivate the automatic transfer so that the HMI device cannot be inadvertently switched to transfer mode. The transfer mode can trigger unintentional reactions in the system. You can issue a password in the Control Panel to restrict access to the transfer settings and thus avoid unauthorized modifications. Requirement The Control Panel is open. The Runtime software is terminated. MP 277 Operating Instructions, 07/2014, A5E02479740-02 137 Commissioning a project 7.5 Transfer project to the HMI device Procedure Proceed as follows: 1. Open the "Transfer Settings" dialog with the Transfer Settings icon. 2. Open the "Channel" tab. 3. Select "Enable Transfer". 4. Select the data channel and set its parameters using "Properties...". Exception: The "USB device" data channel has no parameters. 5. To start "Transfer" mode automatically: - Select "Remote Control". - Close the dialog with "OK". 6. To start "Transfer" mode manually: - Disable "Remote Control". - Close the dialog with "OK". - Close the Control Panel. - Enable transfer mode in the loader with "Transfer". Result "Transfer" mode is set. The project is transferred from the configuration PC via the data channel selected on the HMI device. If required, configure the corresponding data channel on the configuration PC. Transferred data is written directly to the internal memory of the HMI device. Alternative procedure You can also set "Transfer" mode on the HMI device using an operating element in the project. To do this, configure the "SetDeviceMode" system function on an operating element event, for example, on a button. You can find more information on this topic in the WinCC online help. See also Configuring the data channel (Page 109) MP 277 138 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.5 Transfer project to the HMI device 7.5.1.2 Starting the transfer Introduction To make a project executable on an HMI device, transfer the project from the configuration PC to the HMI device. With a transfer, you particularly specify whether to overwrite existing data on the HMI device such as "User management" or "Recipe data". Requirement The project is opened in WinCC on the configuration PC. Project tree is displayed. configuration PC is connected to the HMI device. Transfer mode is set on the HMI device. Procedure Proceed as follows: 1. Select the "Download to device > Software" command in the shortcut menu of the HMI device. 2. When the "Extended download to device" dialog opens, configure the "Transfer settings". Make sure that the "Transfer settings" match the "Transfer settings on the HMI device": - Select the protocol used, for example, Ethernet or USB. If you are using Ethernet or PROFINET, you can also configure the network address in the "Devices & Networks" editor in WinCC. You can find more information on this topic in the WinCC online help. - Configure the corresponding interface parameters on the configuration PC. - Make the specific interface or protocol settings on the HMI device as required. - Click "Download". You can open the "Extended download to device" dialog at any time using the menu command "Online > Extended download to device...". The "Load preview" dialog opens. The project is compiled at the same time. The result appears in the "Load preview" dialog. 3. Check the displayed default settings and change them, if necessary. 4. Click "Download". Result The project is transferred to the selected HMI device. If errors or warnings occur during the transfer, alarms are displayed in the Inspector window under "Info> Download". When the transfer is completed successfully, the project is executable on the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 139 Commissioning a project 7.5 Transfer project to the HMI device 7.5.1.3 Testing a project Introduction There are two options to test a project: Test the project on the configuration PC You can test a project on a configuration PC, using a simulator. You can find more detailed information on this in the WinCC online help. Offline testing of the project on the HMI device Offline testing means that communication between the HMI device and the controller is down while the test is being carried out. Online testing of the project on the HMI device Online testing means that the HMI device and the controller communicate with each other during testing. Perform the tests, starting with the "Offline test", followed by the "Online test". Note You should always test the project on the HMI device on which the project will be used. Check the following: 1. Check the correct layout of the screens 2. Check the screen navigation 3. Check the input objects 4. Enter the tag values The test increases the certainty that the project will run error-free on the HMI device. Requirement for offline testing The project has been transferred to the HMI device. The HMI device is in "Offline" mode. Procedure In "Offline" mode, you can test individual project functions on the HMI device without them being affected by the controller. Controller tags, therefore, are not updated. Test the operating elements and visualization of the project as far as possible without connection to the controller. MP 277 140 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.5 Transfer project to the HMI device Requirement for online testing The project has been transferred to the HMI device. The HMI device is in "Online" mode. Procedure In "Online" mode, you can test individual project functions on the HMI device without them being affected by the controller. Controller tags are updated in this case. You have the option to test all communication-related functions, such as alarms, etc. Test the operating elements and views of the project. 7.5.2 Transfer project with WinCC flexible 7.5.2.1 Overview Transfer Transfer the executable project from the configuring PC to the HMI device. You can start the "Transfer" mode manually or automatically on the HMI device. Transferred data is written directly to the internal flash memory on the HMI device. For the transfer, you use a data channel which you have to configure before starting a transfer. Backtransfer You have the option to transfer the compressed project file together with the runtime project to the HMI device. If necessary, the compressed project file can be transferred back to the configuring PC and edited. The HMI device must be equipped with an external memory card to which the compressed project file can be saved. Note Compressed project file WinCC flexible does not check whether the compressed project file stored on the HMI device corresponds to the existing runtime project. MP 277 Operating Instructions, 07/2014, A5E02479740-02 141 Commissioning a project 7.5 Transfer project to the HMI device 7.5.2.2 Starting manual transfer Introduction You can manually switch the HMI device to "Transfer" mode as follows: With a configured operating element during ongoing operation. In the Loader of the HMI device. Requirements The project "*.hmi" is opened in WinCC flexible. The HMI device is connected to a configuring PC The data channel is configured on the HMI device The HMI device is in "Transfer" mode Procedure Proceed as follows: 1. On the configuring PC, select the "Transfer settings" command in the menu "Project > Transfer" in WinCC flexible. The "Select devices for transfer" dialog opens. 2. Select the HMI device in the left area of the dialog. 3. Select the type of connection between the HMI device and the configuring PC. Set the connection parameters. 4. Set the transfer parameters in the right area of the dialog. 5. If you wish to transfer the compressed project file together with the runtime project to the HMI device: Select the "Enable backtransfer" check box. 6. Start transfer in WinCC flexible with "Transfer". The configuring PC checks the connection to the HMI device. The project is transferred to the HMI device. If the connection is not available or is defective, an error message is displayed on the configuring PC. Result When the transfer is completed successfully, the project can be found on the HMI device. The transferred project is then started automatically. See also Operating modes (Page 134) Configuring the data channel (Page 109) Data Transmission Options (Page 136) MP 277 142 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.5 Transfer project to the HMI device 7.5.2.3 Starting automatic transfer Introduction The HMI device can be automatically switched to "Transfer" mode during runtime as soon as transfer is started on the configuring PC connected. Automatic transfer is particularly suited for the test phase of a new project since transfer is completed without interfering with the HMI device. Automatic transfer is available for the following data channels: Serial MPI/PROFIBUS DP USB Ethernet Note If the automatic transfer has been activated on the HMI device and a transfer is initiated on the configuring PC, the project currently running is automatically stopped. The HMI device then automatically switches to "Transfer" mode. After the commissioning phase, deactivate the automatic transfer so that the HMI device cannot be inadvertently switched to transfer mode. The transfer mode can trigger unintentional actions in the device. You can set a password for the Loader of the HMI device to restrict access to the transfer settings and thus avoid unauthorized modifications. Requirements The project *.hmi is opened in WinCC flexible. The HMI device is connected to a configuring PC The data channel is configured on the HMI device The automatic transfer is activated in the data channel for the transfer. The project is started on the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 143 Commissioning a project 7.5 Transfer project to the HMI device Procedure Proceed as follows: 1. On the configuring PC, select the "Transfer settings" command in the menu "Project > Transfer" in WinCC flexible. The "Select devices for transfer" dialog opens. 2. Select the HMI device in the left area of the dialog. 3. Select the type of connection between the HMI device and the configuring PC. Set the connection parameters. 4. Set the transfer parameters in the right area of the dialog. 5. If you wish to transfer the compressed project file together with the runtime project to the HMI device: Select the "Enable backtransfer" check box. 6. Start transfer in WinCC flexible with "Transfer". The configuring PC checks the connection to the HMI device. The HMI device shuts down the current project and automatically switches to "Transfer" mode The project is transferred to the HMI device. If the connection is not available or is defective, an error message is displayed on the configuring PC. Result When the transfer is completed successfully, the project can be found on the HMI device. The transferred project is then started automatically. See also Operating modes (Page 134) Configuring the data channel (Page 109) Data Transmission Options (Page 136) 7.5.2.4 Starting backtransfer Requirements No project is open on the configuring PC in WinCC flexible The HMI device is connected to this configuring PC The data channel is configured on the HMI device The HMI device is in "Transfer" mode The memory card containing the compressed project file is inserted into the HMI device MP 277 144 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.5 Transfer project to the HMI device Procedure Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication Settings" dialog opens. 2. Select the type of HMI device. 3. Select the type of connection between the HMI device and the configuring PC. Set the connection parameters. 4. Close the dialog with "OK". 5. Select the "Transfer" > "Backtransfer" command in the "Project" menu. The "Backtransfer" dialog opens. 6. Click "OK" to start the backtransfer process. The configuring PC checks the connection to the HMI device. The compressed project file is transferred back from the HMI device to the configuring PC. If the connection is not available or is defective, an error message is displayed on the configuring PC. Result After successful backtransfer, the project is opened on the configuring PC in WinCC flexible. 7.5.2.5 Testing a project Introduction There are two options to test a project: Test the project on the configuring PC You can test a project at a configuring PC, using a simulator. For detailed information, refer to the "WinCC flexible" user manual and to the WinCC flexible Online Help. Offline testing of the project on the HMI device Offline testing means that communication between the HMI device and PLC is down while the test is being carried out. Online testing of the project on the HMI device Online testing means that the HMI device and PLC communicate with each other during testing. Perform the tests, starting with the "Offline test", followed by the "Online test". Note You should always test the project on the HMI device on which the project will be used. MP 277 Operating Instructions, 07/2014, A5E02479740-02 145 Commissioning a project 7.5 Transfer project to the HMI device Check the following: 1. Check the correct layout of the screens 2. Check the screen navigation 3. Check the input objects 4. Enter the tag values The test increases the certainty that the project will run error-free on the HMI device. Requirements for offline testing The project has been transferred to the HMI device The HMI device is in "Offline" mode Procedure In "Offline" mode, you can test individual project functions on the HMI device without them being affected by the PLC. PLC tags, therefore, are not updated. Test the operating elements and visualization of the project as far as possible without connecting to the PLC. Requirements for online testing The project has been transferred to the HMI device The HMI device is in "Online" mode Procedure In "Online" mode, you can test individual project functions on the HMI device without them being affected by the PLC. PLC tags are updated in this case. You have the option to test all communication-dependent functions, for example alarms, etc. Test the operating elements and views of the project. MP 277 146 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.6 Backup and restore 7.6 Backup and restore 7.6.1 Overview Note Power failure If a complete restore operation is interrupted due to power failure on the HMI device, the operating system of the HMI device may be deleted. The operating system then has to be updated. Compatibility conflict If a message is output on the HMI device warning of a compatibility conflict during the restore operation, the operating system must be updated. Backing up and restoring by means of external storage device The "Backup / Restore" function is approved for MMC and SD memory cards as well as USB mass storage devices. Backing up and restoring by means of PC Note License keys License keys are not taken into account for backups and restores. License keys are saved in the working memory of the HMI device and cannot be deleted. You can back up and restore the following data found in the internal flash memory of the HMI device with a PC: Project and HMI device image Password list Recipe data Use one of the following tools for backup and restore: WinCC WinCC flexible ProSave The backup and restore with ProSave is described below. Information on backup and restore with WinCC or WinCC flexible is described in the associated online help. MP 277 Operating Instructions, 07/2014, A5E02479740-02 147 Commissioning a project 7.6 Backup and restore 7.6.2 Backup and restore using ProSave Requirements The HMI device is connected to a PC on which ProSave is installed The data channel is configured on the HMI device Procedure for backup Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. Set the connection parameters. 4. Select the data to be backed up in the "Backup" tab. 5. Select a destination folder and a file name for the "*.psb" backup file. 6. Set "Transfer" mode on the HMI device. If automatic transfer mode is enabled on the HMI device, the HMI device automatically sets "Transfer" mode when a backup is initiated. 7. Start the backup operation in ProSave with "Start Backup". Follow the instructions in ProSave. A status view opens to indicate the progress of the operation. Result The system outputs a message when the backup is completed. The relevant data is now backed up on the PC. Procedure for restore Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. Set the connection parameters. 4. Select the "*.psb" backup file to be restored from the "Restore" tab. You can see the HMI device for which the backup file was created and the type of backup data the file contains. MP 277 148 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.7 Updating the operating system 5. Set "Transfer" mode on the HMI device. If automatic transfer mode is enabled on the HMI device, the device automatically sets "Transfer" mode when a restore operation is initiated. 6. Start the restore operation in ProSave on the PC with "Start Restore". Follow the instructions in ProSave. A status view opens to indicate the progress of the operation. Result When the restore is successfully completed, the data backed up on the PC is now on the HMI device. See also Overview (Page 147) Data Transmission Options (Page 136) Operating modes (Page 134) Configuring the data channel (Page 109) 7.7 Updating the operating system 7.7.1 Overview A compatibility conflict may occur when transferring a project to the HMI device. This is caused by different versions of the configuration software used and the HMI device image available on the HMI device. If there are different versions, the transfer is aborted. A message indicating a compatibility conflict is displayed on the configuration PC. There are two ways to match the versions: Update the HMI device image if the project was created with a more recent version of the configuration software. Transfer a matching version of the HMI device image if you do not want to adapt the project for the HMI device to the current version of the configuration software for the project. MP 277 Operating Instructions, 07/2014, A5E02479740-02 149 Commissioning a project 7.7 Updating the operating system Note * Two versions are available for each device type - recognizable by their article number. The images of the device versions are not compatible. * All data on the HMI device, such as the project and licenses, will be deleted when you update the operating system. * When WinAC MP is used, all data channel parameters are reset. * After the update, you may have to recalibrate the touch screen. Resetting to factory settings In ProSave, WinCC or WinCC flexible, you can update the operating system with or without resetting to factory settings. Updating the operating system without reset to factory settings First, switch into "Transfer" mode on the HMI device or use the automatic transfer function if the project is active. Then start the operating system update in ProSave, WinCC or WinCC flexible. Updating the operating system with reset to factory setting Note Loss of license keys The license keys on the HMI device is deleted when resetting to factory settings. The license keys on the HMI device are retained when updating the operating system without resetting to factory settings. Note Data channels When resetting to factory settings, all data channel parameters are reset. The transfer can only be started following reconfiguration of the data channels. Note You have to perform an operating system update with reset to factory setting if the HMI device does not yet have an operating system or if the HMI device's operating system is corrupt. First, start the operating system update in ProSave, WinCC or WinCC flexible, and switch the power on the HMI device off and on again when prompted. The update of the operating system with ProSave is described below. Information on update of the operating system with WinCC or WinCC flexible is described in the associated online help. MP 277 150 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.7 Updating the operating system 7.7.2 Updating the Operating System using ProSave Requirement The HMI device is connected to a PC on which ProSave is installed. When updating the operating system without reset to factory settings only: The data channel is configured on the HMI device. Procedure Proceed as follows: 1. When updating the operating system with reset to factory settings only: Switch off power to the HMI device. 2. Go to the Windows Start menu and start ProSave on the PC. 3. Select the HMI device type in the "General" tab. 4. Select the type of connection between the HMI device and the PC, then set the connection parameters. 5. Select the "OS Update" tab. 6. Select whether to update the operating system with or without restoring the factory settings by setting the "Reset to factory settings" check box accordingly. 7. Select the HMI device image file "*.img" under "Image path". The HMI device image files are available under "WinCC flexible Images" in the WinCC flexible installation folder or on the WinCC flexible installation CD. The output area provides information on the version of the successfully opened HMI device image file. 8. When updating without reset to the factory settings only: Set "Transfer" mode on the HMI device. If automatic transfer mode is enabled on the HMI device, the device automatically sets "Transfer" mode when an update is initiated. 9. Select "Update OS" on the PC to run the operating system update. 10. When updating with reset to the factory settings only: Switch on the power supply to the HMI device. 11. Follow the instructions in ProSave. Result A progress bar indicates the progress of the operating system update. A message is displayed when the operating system update is successfully completed. The HMI device no longer contains any project data. See also Overview (Page 152) Configuring the data channel (Page 109) Operating modes (Page 134) Data Transmission Options (Page 136) MP 277 Operating Instructions, 07/2014, A5E02479740-02 151 Commissioning a project 7.8 Installing and removing options 7.8 Installing and removing options 7.8.1 Overview You can install options on the HMI device, for example, additional programs developed especially for the HMI device. You can also remove the option from the HMI device again. Note License key A license key may be needed to run an option. The license key unlocks the option for use. The installation of options with ProSave is described below. Information on installation of options with WinCC or WinCC flexible is described in the associated online help. 7.8.2 Installing and removing options using ProSave Requirement The HMI device is connected to a PC on which ProSave is installed. The data channel is configured on the HMI device. Procedure for installing an option Proceed as follows: 1. Go to the Windows Start menu and start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. 4. Set the connection parameters. 5. Select the "Options" tab. 6. Select the desired option under "Available options". 7. Set "Transfer" mode on the HMI device. If automatic transfer mode is enabled on the HMI device, the device automatically sets "Transfer" mode when the installation of an option is initiated. 8. Start the installation of the option in ProSave with the ">>" button. 9. Follow the instructions in ProSave. A status display appears indicating the progress of the installation. MP 277 152 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.8 Installing and removing options Result The option has now been installed on the HMI device. Procedure for removing an option Proceed as follows: 1. Go to the Windows Start menu and start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. 4. Set the connection parameters. 5. Select the "Options" tab. 6. Press the "Device status" button to update the display. 7. Select the desired option under "Installed options". 8. Set "Transfer" mode on the HMI device. If automatic transfer mode is enabled on the HMI device, the device automatically sets "Transfer" mode when the removal of an option is initiated. 9. Start the removal of the option in ProSave with the "<<" button. Follow the instructions in ProSave. A status display appears indicating the progress of the removal. Result The option has now been removed on the HMI device. See also Overview (Page 152) Configuring the data channel (Page 109) Operating modes (Page 134) Data Transmission Options (Page 136) MP 277 Operating Instructions, 07/2014, A5E02479740-02 153 Commissioning a project 7.9 Transferring and transferring back license keys 7.9 Transferring and transferring back license keys 7.9.1 Overview With the purchase of an add-on package, you obtain a specific user license with an associated license key. Once you have installed an add-on, transfer a license key to the HMI device. The license key unlocks an add-on for use. You can also transfer back the license key from the HMI device to a license diskette. Note License keys can only be transferred and transferred back with the Automation License Manager or the configuration software. The transfer and back transfer of license keys with the "Automation License Manager" is described below. Information on transfer and back transfer of license keys with WinCC or WinCC flexible is described in the associated online help. 7.9.2 Transfer of license keys with the Automation License Manager Requirement The HMI device is connected to the configuration PC or to the PC with the "Automation License Manager". If you use the configuration PC: The HMI device is selected in the project tree. Procedure To transfer the license keys, follow these steps: 1. Open the "Automation License Manager". On a PC without a WinCC installation, open the "Automation License Manager" from the Windows Start menu. The "Automation License Manager" starts. 2. Select the "Connect HMI device" command in the "Edit > Connect Target System" menu. The "Connect target system" dialog opens. 3. Select the "device type" of your HMI device. 4. Select the "connection". MP 277 154 Operating Instructions, 07/2014, A5E02479740-02 Commissioning a project 7.9 Transferring and transferring back license keys 5. Configure the corresponding "connection parameters", depending on the selected connection. 6. Click "OK". The connection to the HMI device is established. The connected HMI device is displayed in the left area of the "Automation License Manager". 7. Transfer the license keys to the HMI device: - In the left area, select the drive on which the license keys are located. The license keys are shown in the right area. - Select the license keys. - Drag-and-drop the license keys to the HMI device. You can also remove license keys from the HMI device by means of drag-and-drop. Alternative procedure On a PC with a WinCC installation, you can also launch the "Automation License Manager" from WinCC: Select the "Authorize/License" command in the "Online > HMI device maintenance" menu. Result The license keys are transferred to the HMI device. To back up the license keys on the HMI device, drag them from the HMI device to an available drive. MP 277 Operating Instructions, 07/2014, A5E02479740-02 155 Commissioning a project 7.9 Transferring and transferring back license keys MP 277 156 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.1 8 Overview Configuration and process control phase HMI devices can be used to operate and monitor tasks in process and production automation. The plant screens on the HMI devices are used to provide a clear overview of the active processes. The HMI device project, which includes the plant screens, is created during the configuration phase. The configuration engineer defines which tasks the HMI device has in the process and defines the following in detail: Which process data is displayed on the individual HMI device Which plant components are controlled by this HMI device The configuration engineer stores this information in the project's screens. The project is transferred to the HMI device during commissioning. After transfer to the HMI device, current processes can be operated and monitored in the project's screens. The screens enable you to observe, for example, operational states, current process data and faults in a plant. Operating elements which are used to operate the process, for example buttons, I/O fields and alarm windows, are displayed in the screens. Operator control options The hardware of the HMI device determines which of the following operator control options are available: Touch screen The operating elements shown in the dialogs are touch-sensitive. Touch objects are basically operated in the same way as mechanical keys. You activate operating elements by touching them with your finger. To double-click them, touch an operating element twice in succession. HMI device keyboard The operating elements shown in the screens are selected and operated using the keys of the HMI device. External keyboard, connected via USB External mouse, connected via USB MP 277 Operating Instructions, 07/2014, A5E02479740-02 157 Operating a project 8.1 Overview CAUTION Risk of damage to the touch screen Do not use pointed or sharp objects to operate the touch screen. Otherwise, you can damage the plastic membrane of the touch screen. The following paragraphs provide instructions for operating a project with the touch screen and the keyboard. Operating a project with an external keyboard An external keyboard can be used to operate a project in exactly the same way as with the HMI keyboard or screen keyboard. Note The function keys of the external keyboard are disabled. Use the other keys of the external keyboard, which correspond to the HMI device keys in the description. Operating a project with an external mouse The project can be operated with an external mouse in exactly the same way as with the HMI touch screen. Click the described operating elements with the mouse. Unintentional actions CAUTION Unintentional actions possible Do not carry out several operations simultaneously. You may otherwise trigger unintentional actions. * With touch control: Always touch only one operating element on the screen. * With key control: Do not press more than two keys simultaneously. Observing the plant documentation Some operations with the project may require in-depth knowledge about the specific plant on the part of the operator. Proceed with caution, for example, when you use jog mode. Refer to your plant documentation to find any available additional information on this topic. MP 277 158 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.1 Overview Operation feedback from operating elements The HMI device provides operation feedback as soon as it detects that an operating element has been selected. This operation feedback is independent of any communication with the PLC. Therefore, this operation feedback does not indicate whether the relevant action is actually executed or not. Optical feedback from operating elements The operating element receives the focus and is selected. The configuration engineer can also configure the selection of an operating element so that it deviates from the standard. Refer to your plant documentation to find any available additional information on this topic. The type of optical feedback depends on the operating element: Buttons The HMI device outputs different views of the "Pressed" and "Unpressed" states, provided the configuration engineer has configured a 3D effect: - "Pressed" state: - "Unpressed" state: The configuration engineer determines the appearance of a selected field, for example, line width and color for the focus. Invisible buttons By default, invisible buttons are not displayed as pressed when they are touched. No optical feedback is provided in this case. The configuration engineer may, however, configure invisible buttons so that their outline appears as lines when touched. This outline remains visible until you select another operating element. I/O fields When you select an I/O field, the content of the I/O field is displayed against a colored background. With touch operation, a screen keyboard is displayed for the entering of values. MP 277 Operating Instructions, 07/2014, A5E02479740-02 159 Operating a project 8.2 Direct keys Acoustic feedback from operating elements An acoustic signal is generated as soon as the HMI device detects that the touch screen has been touched or a key has been pressed. You can activate or deactivate this acoustic operation feedback. Note The acoustic feedback is only possible if you interact with the project directly on the touch screen or press one of the keys of the HMI device. If you use an external mouse or keyboard for interaction, no acoustic signal is issued. Acoustic signal for inadvertent operations If you try to enter an invalid character, the HMI device issues an acoustic signal in accordance with the setting. See also Set the volume (Page 97) 8.2 Direct keys Introduction Direct keys on the HMI device are used to set bits in the I/O area of a SIMATIC S7. Direct keys enable operations with short reaction times that are, for example, a jog mode requirement. Note Direct keys are still active when the HMI device is in "offline" mode. Note If you operate a function key with direct key functionality in a running project, the direct key function is always executed, independent of the current screen contents. Note You can only use direct keys when there is a connection via PROFIBUS DP or PROFINET IO. Direct keys result in additional basic load on the HMI device. MP 277 160 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.3 Setting the project language Direct keys The following objects can be configured as a direct key: Buttons Function keys You can also define image numbers in the case of HMI devices with touch operation. In this way, the project engineer can configure the direct keys on an image-specific basis. Further information on configuring direct keys can be found in the "WinCC flexible Communication" system manual. See also Bit assignment of the direct keys (Page 189) Enabling PROFINET IO (Page 111) 8.3 Setting the project language Introduction The HMI device supports multilingual projects. You must have configured a corresponding operating element which lets you change the language setting on the HMI device during runtime. The project always starts with the language set in the previous session. Requirements The required language for the project must be available on the HMI device The language switching function must be logically linked to a configured operating element such as a button Selecting a language You can change project languages at any time. Language-specific objects are immediately output to the screen in the new language when you switch languages. The following options are available for switching the language: A configured operating element switches from one language to the next in a list A configured operating element directly sets the desired language Please refer to your system documentation to check whether additional information on this subject is available there. See also Changing Regional Settings (Page 92) MP 277 Operating Instructions, 07/2014, A5E02479740-02 161 Operating a project 8.4 Entering values using the touch screen 8.4 Entering values using the touch screen 8.4.1 Overview Screen keyboard A screen keyboard appears on the HMI device touch screen when you touch an operating element that requires input. The screen keyboard is displayed in the following cases: An I/O field is selected for input A password must be entered for accessing a password-protected function The screen keyboard is automatically hidden again when input is complete. Based on the configuration of the operating element, the system displays different screen keyboards for entering numerical or alphanumerical values. Note The screen keyboard display is independent of the configured project language. General procedure The operating elements of a screen are operated by touching the touch screen. Proceed as follows: 1. Touch the desired operating element within the screen. 2. Depending on the operating element, perform further actions. Detailed descriptions can be found under the respective operating element. Examples: - I/O field: Enter numerical, alphanumerical or symbolic values in the I/O field - Symbolic I/O field: Select an entry from the drop down list box - Slider control: Move the slider control MP 277 162 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.4 Entering values using the touch screen Procedure for text boxes Values are entered in the project text boxes. Based on your configuration, the values are saved to tags and transferred, for example, to the PLC. Proceed as follows: 1. Touch the desired text box within the screen. The screen keyboard opens. Depending on your configuration, you can enter values in the text box in the following manner: - Numerical values, for example decimal numbers, hexadecimal numbers, binary values - Alphanumerical values, for example digits and letters - Date/time 2. Enter the value. 3. Confirm your entry with 8.4.2 or discard your entry with . Entering and Editing Numerical Values Numerical screen keyboard When you touch an operating element for numerical input on the HMI device touch screen, the numerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete. Note Opened screen keyboard When the screen keyboard is open, PLC job 51, "Select screen" has no function. MP 277 Operating Instructions, 07/2014, A5E02479740-02 163 Operating a project 8.4 Entering values using the touch screen Formats for numerical values You can enter values in numerical text boxes based on the following formats: Decimal Binary Hexadecimal Note Entry of hexadecimal values When you enter values in hexadecimal format, the alphanumerical screen keyboard opens. Limit test of numerical values Tags can be assigned limits. If you enter a value that lies outside of this limit, it will not be accepted, for example, 80 with a limit of 78. In this case the HMI device will deliver a system alarm, if an alarm window is configured. The original value is displayed again. Decimal places for numerical values The configuration engineer can define the number of decimal places for a numerical text box. The number of decimal places is checked when you enter a value in this type of I/O field. Decimal places in excess of the limit are ignored. Empty decimal places are filled with "0". MP 277 164 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.4 Entering values using the touch screen Procedure Numerical values can be entered character-by-character via the buttons on the numerical screen keyboard. Proceed as follows: 1. Touch the desired operating element within the screen. The numerical screen keyboard opens. The existing value is displayed in the screen keyboard and is selected. 2. Enter the value. The keys with for example the letters G to Z are available to enter a hexadecimal value; however, the characters are not entered. Depending on the settings, the HMI device outputs an audible signal. You have the following options to enter a value: - The selected value is deleted when you enter the first character. Completely reenter the value. - Use the and keys to move the cursor within the current value. You can now edit the characters of the current value or add characters. Use the key to delete the character to the left of the cursor. If the value is selected, use this key to delete the selected part of the value. The key deletes the character positioned to the right of the cursor. If the value is selected, use this key to delete the selected part of the value. - Use the key to display the info text of the I/O field. This key is only enabled if info text has been configured for the input object or the current screen. 3. Use the key to confirm your entry or cancel it with screen keyboard. . Either action closes the Result You have changed the numerical value or entered a new one. MP 277 Operating Instructions, 07/2014, A5E02479740-02 165 Operating a project 8.4 Entering values using the touch screen 8.4.3 Entering and editing alphanumerical values Alphanumerical screen keyboard When you touch an operating element for alphanumerical input on the HMI device touch screen, the alphanumerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete. Note Opened screen keyboard When the screen keyboard is open, PLC job 51, "Select screen" has no function. Language switching Language switching in the project has no influence on the alphanumerical screen keyboard. The entry of Cyrillic or Asian characters is therefore not possible. Keyboard levels The alphanumerical screen keyboard has various levels: Normal level Shift level If you change the levels with key , the key assignments change. MP 277 166 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.4 Entering values using the touch screen Procedure Alphanumerical values can be entered character-by-character via the buttons on the alphanumerical screen keyboard. Proceed as follows: 1. Touch the desired operating element within the screen. The alphanumerical screen keyboard opens. The existing value is displayed in the screen keyboard and is selected. 2. Enter the value. You have the following options to enter a value: - The selected value is deleted when you enter the first character. Completely reenter the value. - Use the and keys to move the cursor within the current value. You can now edit the characters of the current value or add characters. Use the key to delete the character to the left of the cursor. If the value is selected, use this key to delete the selected part of the value. The key deletes the character positioned to the right of the cursor. If the value is selected, use this key to delete the selected part of the value. - Using key it is possible to switch between the keyboard levels of the screen keyboard. On switchover, the key assignments of the screen keyboard change. - Use the key to display the info text of the I/O field. This key is only enabled if info text has been configured for the input object or the current screen. 3. Use the key to confirm your entry or cancel it with screen keyboard. . Either action closes the Result You have changed the alphanumeric value or entered a new one. MP 277 Operating Instructions, 07/2014, A5E02479740-02 167 Operating a project 8.4 Entering values using the touch screen 8.4.4 Entering the date and time Entering the date and time Enter the date and time in the same way you enter alphanumerical values. Note When entering the date and time, please note that the format is determined by the configured project language. See also Entering and Editing Numerical Values (Page 163) Entering and editing alphanumerical values (Page 166) 8.4.5 Entering Symbolic Values Selection list Operating element for entering symbolic values offer you a list from which you can select the input values. When you touch a symbolic I/O field on the HMI device touch screen, the following selection list opens. Procedure Proceed as follows: 1. Touch the required operating element. The selection list of the operating element opens. Select selection list. and to scroll in the 2. Touch the required entry in the selection list. The selected entry is accepted as an entry. Result You have changed the symbolic value or entered a new one. MP 277 168 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.4 Entering values using the touch screen 8.4.6 Displaying Infotext Purpose The configuration engineer uses info text to provide additional information and operating instructions. The configuration engineer can configure info text on screens and operator controls. The infotext of an I/O field can contain, for example, information on the value to be entered. Opening info text for operator controls 1. Touch the required operator control. The screen keyboard opens. You can see from the appearance of the key whether info text has been configured for the operator control or the current screen. 2. Touch the key on the screen keyboard. The info text for the operator control is displayed. If there is no info text for the selected screen object, the info text for the current screen is displayed, if it has been configured. You can scroll through the contents of long info text with and . Note Switching between displayed info text The configuration engineer can configure infotext for an I/O field and the associated screen. You can switch between two info texts by touching the info text window. 3. Close the displayed info text by pressing . Alternative procedure Depending on your configuration, info text can also be called via a configured operator control. Refer to your plant documentation to find any available additional information on this topic. MP 277 Operating Instructions, 07/2014, A5E02479740-02 169 Operating a project 8.5 Entering values using the keys 8.5 Entering values using the keys 8.5.1 Control keys Introduction The following tables show the control keys with which you operate the project. Multi-key operation Unwanted actions may be triggered, if the operator unintentionally actuates a key combination. CAUTION Unintentional actions In "Online" mode, simultaneous operation of more than two keys may cause unintentional actions in the plant. Never press more than two keys simultaneously. Select operating elements Key/Keys - Function Description Tabulator Selects the next/previous operating element in the tab sequence. Cursor keys Navigates in the operating element. MP 277 170 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.5 Entering values using the keys Using operating elements Key/Keys - - - Function Description Position the cursor Positions the cursor within an operating element, e.g. in the I/O field. Scroll back Scrolls back a page in a list. Scroll to the beginning Scrolls to the beginning of a list. Scroll forward Scrolls one page forward in a list. Scroll to the end Scrolls to the end of a list. Enter key * Operates buttons. * Accepts and ends an entry. * Opens a selection list. * Toggles within a text box between character mode and normal mode. In character mode, a single character is selected. In this mode, you can advance in the character set using the cursor keys. - Cancel * Deletes the characters of a value entry and restores the original value. * Closes the active dialog. - Delete characters Deletes the character to the right of the current cursor position. - Delete characters Deletes the character to the left of the current cursor position. Open selection list Opens a selection list. Accept value Accepts the selected value in the selection list without closing the list. MP 277 Operating Instructions, 07/2014, A5E02479740-02 171 Operating a project 8.5 Entering values using the keys Enter key combinations Key Function Purpose Toggle key assignment Switches over key assignment of keys with multiple assignment. * No LED is lit: The number assignment is enabled. Pressing the button once toggles to letter assignment. * An LED is lit: The left or right letter assignment is enabled. Each time the key is pressed, the system toggles between the left letter assignment, the right letter assignment and the number assignment. Toggle between upper-case and lower-case Used in key combinations, for example for entering upper-case letters. Switch to additional key assignment Some of the keys contain a key assignment imprinted blue, for example the "%" character. Used in key combinations for the blue key assignment. General control function Used in key combinations General control function Used in key combinations Function Description Acknowledge Acknowledges the currently displayed fault alarm or all the alarms of an alarm group as group acknowledgment. Acknowledge alarms Key The LED lights up as long as unacknowledged fault alarms are active. Displaying info text Key Function Description Displaying info text Opens a window with the configured info text at the selected object, e.g. alarm or I/O field. If an info text exists for the selected object, the LED lights up. MP 277 172 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.5 Entering values using the keys 8.5.2 Example: Enter characters using the alphanumeric keyboard Using the same keys of the alphanumeric keyboard you can enter up to six different characters. The entry result depends on the combination of the keys pressed. The values "5", "M", "m", "N", "n" and "%" are entered using the same key keyboard. You can use the keys , and of the to switch between the different assignments.. The following table shows the entry options using the key 8.5.3 . Result Key Key Key No LED is lit Not relevant Not pressed 5 Left LED is illuminated. Not pressed Not pressed m Left LED is illuminated. Pressed Not pressed M Right LED is illuminated. Not pressed Not pressed n Right LED is illuminated. Pressed Not pressed N Not relevant Not relevant Pressed % Function keys Function keys Function key assignment is defined during configuration. The configuration engineer can assign function keys globally and locally. Function keys with global function assignment A globally assigned function key always triggers the same action on the HMI device or in the PLC irrespective of the screen displayed. Such an action could be, for example, the activation of a screen or the closure of an alarm window. Function keys with local function assignment A function key with local function assignment is screen-specific and is therefore only effective within the active screen. The function assigned locally to a function key can vary from screen to screen. The function key of a screen can be assigned one function only, either a global or local one. The local assignment function takes priority over the global setting. The configuration engineer can assign function keys in such a way that you can manipulate operating elements with function keys, for example, the alarm view, trend view, recipe view or status/force. MP 277 Operating Instructions, 07/2014, A5E02479740-02 173 Operating a project 8.5 Entering values using the keys 8.5.4 General procedures Introduction The control keys and function keys of the HMI device are available for key control General procedure The operating elements of a screen are operated using the control keys of the HMI device. Proceed as follows: 1. Continue to press the key selected on the screen. or the cursor keys until the required operating element is 2. Depending on the operating element, perform further actions. Detailed descriptions can be found under the respective operating element. Examples: - I/O field: Enter numerical, alphanumeric or symbolic values in the I/O field - Slider control: Move the slider control 3. Confirm the operation with the key 8.5.5 or abort the operation with the key . Entering and editing numerical values Formats for numerical values You can enter values in numerical text boxes based on the following formats: Decimal Hexadecimal Binary Limit value test of numerical values Tags can be assigned limit values. If you enter a value that lies outside of this limit, it will not be accepted, for example, 80 with a limit value of 78. In this case the HMI device will deliver a system alarm, if an alarm window is configured. The original value is displayed again. MP 277 174 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.5 Entering values using the keys Procedure Numerical and alphanumerical values can be entered in character mode using the system keys. Proceed as follows: 1. Select the desired text box within the screen with . The existing value is selected in the text box. 2. Enter the value using the numerical keypad. You have the following options to enter a value: - The existing value is deleted when you enter the first character. Completely reenter the value. - Press and a cursor key simultaneously. The selection of the field content is canceled. Move the cursor in the existing value. You can now edit the characters of the current value or add characters. The key deletes the character positioned to the right of the cursor. Use the key to delete the character to the left of the cursor. To enter the hexadecimal characters "A" to "F", switch the numerical keypad to letter assignment using the key . - If the LED of the current screen. key is lit, infotext is available for the selected object or the Use the key to display the infotext for the operating element or current screen. 3. Select to confirm your entry. Result You have changed the numerical value or entered a new one. MP 277 Operating Instructions, 07/2014, A5E02479740-02 175 Operating a project 8.5 Entering values using the keys 8.5.6 Entering and editing alphanumerical values Procedure Alphanumerical values can be entered in character mode using the system keys. Proceed as follows: 1. Select the desired text box within the screen with . The existing value is selected in the text box. 2. Enter the value using the system keys. You have the following options to enter a value: - The existing value is deleted when you enter the first character. Completely reenter the value. - Press and a cursor key simultaneously. The selection of the field content is canceled. Move the cursor in the existing value. You can now edit the characters of the current value or add characters. The key deletes the character positioned to the right of the cursor. Use the key to delete the character to the left of the cursor. To enter letters, switch the numerical keypad to letter assignment using the key . - If the LED of the current screen. key is lit, infotext is available for the selected object or the Use the key to display the infotext for the operating element or current screen. 3. Select to confirm your entry. Result You have changed the alphanumeric value or entered a new one. MP 277 176 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.5 Entering values using the keys 8.5.7 Entering the date and time Entering the date and time Enter the date and time in the same way you enter alphanumerical values. Note When entering the date and time, please note that the format is determined by the configured project language. See also Entering and editing numerical values (Page 174) Entering and editing alphanumerical values (Page 176) 8.5.8 Entering Symbolic Values Selection list When you select a symbolic IO field, a selection list opens. Procedure Symbolic values are selected from the entries of a selection list. Proceed as follows: 1. Select the desired symbolic text box within the screen with 2. Open the selection list using the key. The selection list opens. 3. Select the required entry using the cursor keys 4. Confirm your entry with the . , or . key. Result You have changed the symbolic value or entered a new one. MP 277 Operating Instructions, 07/2014, A5E02479740-02 177 Operating a project 8.5 Entering values using the keys 8.5.9 Displaying Infotext Purpose The configuration engineer uses info text to provide additional information and operating instructions. The configuration engineer can configure info text on screens and operator controls. The infotext of an I/O field can contain, for example, information on the value to be entered. If the LED of the key lights up, an infotext has been configured for the selected display object or for the current screen. Procedure 1. Press . The info text for the selected screen object is displayed. If there is no info text for the selected screen object, the info text for the current screen is displayed, if it has been configured. You can scroll through the contents of long info texts using the cursor keys . and Note Switching between displayed info text The configuration engineer can configure infotext for an I/O field and the associated screen. You can switch between two infotexts by pressing the 2. Close the infotext by pressing the key. key. Alternative procedure Depending on your configuration, info text can also be called via a function key or via an existing operator control. Refer to your plant documentation to find any available additional information on this topic. MP 277 178 Operating Instructions, 07/2014, A5E02479740-02 Operating a project 8.6 Closing the project 8.6 Closing the project Procedure Proceed as follows: 1. Use the corresponding operating element object to close the project. Wait for the Loader to open after you closed the project. 2. Switch off power to the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 179 Operating a project 8.6 Closing the project MP 277 180 Operating Instructions, 07/2014, A5E02479740-02 Maintenance and care 9.1 9 Maintenance and care Scope of maintenance The HMI device is designed for maintenance-free operation. The touch screen and keyboard cover should still be cleaned regularly. Preparation CAUTION Inadvertent operation Always switch off the HMI device before cleaning it. This will ensure that you do not trigger functions unintentionally when you touch the keys. Requirement Use a cleaning cloth dampened with a cleaning agent to clean the equipment. Only use water with a little liquid soap or a screen cleaning foam. NOTICE Damage caused by unauthorized cleaning products Do not clean the HMI device with compressed air or steam jet blowers. Never use aggressive solvents or scouring powder. Procedure Proceed as follows: 1. Switch off the HMI device. 2. Spray the cleaning solution onto a cleaning cloth. Do not spray directly onto the HMI device. 3. Clean the HMI device. When cleaning the display wipe from the screen edge inwards. MP 277 Operating Instructions, 07/2014, A5E02479740-02 181 Maintenance and care 9.2 Clean screen on MP 277 Touch 9.2 Clean screen on MP 277 Touch Clean screen The touch screen of the HMI device can be cleaned when it is switched on and a project is running. An operating element must be available in the project with which the clean screen can be called. Once the clean screen is activated, touch screen operation is locked for a configured period of time. The time the touch screen is locked can be set between 5 and 30 seconds. The time remaining for the lockout is indicated by a progress bar. WARNING Locking operating elements Always open the clean screen or switch off the HMI device before you clean the touch screen while the system is running. It is important to note when the clean screen function is unlocked. Ignoring this instruction may lead to inadvertent operation of a function. 9.3 Spare Parts and Repairs Repairs In case of repair, the HMI device must be shipped to the Return Center in Furth. Repairs may only be carried out at the Return Center in Furth. Depending on the work necessary to repair the device, the Center may decide to give you a credit note. In this case, it is your responsibility to order a new device. The address is: Returns Center Siemensstr. 2 90766 Furth Germany Spare parts You can find spare parts and accessories for the HMI devices in the section Accessories (Page 16). 9.4 Recycling and disposal The HMI devices described in these operating instructions can be recycled due to their low levels of pollutants. Contact a certified disposal service company for environmentally sound recycling and disposal of your old devices. MP 277 182 Operating Instructions, 07/2014, A5E02479740-02 10 Technical specifications 10.1 Dimension drawings 10.1.1 Dimension drawing of the MP 277 8" Touch The HMI device MP 277 8" Touch is available in two enclosure models. The enclosure models have different article numbers. The article number is on the back of the HMI device. Article number a b 6AV6643-0CB01-1AX2 250 mm 190 mm 6AV6643-0CB01-1AX1 250 mm 190 mm 6AV6643-0CB01-1AX5 240 mm 180 mm MP 277 Operating Instructions, 07/2014, A5E02479740-02 183 Technical specifications 10.1 Dimension drawings 10.1.2 Dimension drawing of the MP 277 8" Key The HMI device MP 277 8" Key is available in two enclosure models. The enclosure models have different article numbers. The article number is on the back of the HMI device. Article number a b 6AV6643-0CB01-1AX2 362 mm 231 mm 6AV6643-0CB01-1AX1 362 mm 231 mm 6AV6643-0CB01-1AX5 352 mm 221 mm MP 277 184 Operating Instructions, 07/2014, A5E02479740-02 Technical specifications 10.1 Dimension drawings 10.1.3 Dimension drawing of the MP 277 10" Touch The HMI device MP 277 10" Touch is available in two enclosure models. The enclosure models have different article numbers. The article number is on the back of the HMI device. Article number a b 6AV6643-0CD01-1AX2 335 mm 275 mm 6AV6643-0CD01-1AX1 335 mm 275 mm 6AV6643-0CD01-1AX5 325 mm 263 mm MP 277 Operating Instructions, 07/2014, A5E02479740-02 185 Technical specifications 10.2 Specifications 10.1.4 Dimension drawing of the MP 277 10" Key 10.2 Specifications 10.2.1 Specifications of the MP 277 Touch HMI device Weight without packaging MP 277 8" Touch MP 277 10" Touch Approx. 1610 g Approx. 2650 g MP 277 186 Operating Instructions, 07/2014, A5E02479740-02 Technical specifications 10.2 Specifications Display Display area, active MP 277 8" Touch MP 277 10" Touch 153.7 mm x 115.8 mm (7.5") 211.2 mm x 158.4 mm (10.4") Type LCD TFT Resolution 640 x 480 pixels Colors, displayable 64k Brightness control Yes Input device MP 277 8" Touch Type MP 277 10" Touch Resistive analog touch screen Memory MP 277 8" Touch Application memory MP 277 10" Touch 6 MB Ports MP 277 8" Touch 1 x RS 422/RS 485 2 x USB MP 277 10" Touch Max. 12 Mbps USB host; conforms to USB standard 1.1 (supporting low-speed and full-speed USB devices) Maximum load 500 mA 1 x Ethernet RJ45 10/100 Mbps Supply voltage MP 277 8" Touch Rated voltage Range, permissible Transients, maximum permissible Time between two transients, minimum MP 277 10" Touch +24 V DC 20.4 V to 28.8 V (-15%, +20%) 35 V (500 ms) 50 s MP 277 Operating Instructions, 07/2014, A5E02479740-02 187 Technical specifications 10.2 Specifications MP 277 8" Touch MP 277 10" Touch Current consumption * Typical * Approx. 600 mA * Approx. 700 mA * Constant current, maximum * Approx. 1000 mA * Approx. 1100 mA * Power on current surge I2t * Approx. 1 A2s * Approx. 1 A2s Fuse, internal Electronic Miscellaneous MP 277 8" Touch Realtime clock, Yes Magnetic field intensity 1 10.2.2 MP 277 10" Touch buffered 1) 50/60 Hz;100 A/m RMS Bridging time of the buffering, approx. 6 weeks. Specifications of the MP 277 Key HMI device Weight without packaging MP 277 8" Key MP 277 10" Key Approx. 2250 g Approx. 4950 g Display Display area, active MP 277 8" Key MP 277 10" Key 153.7 mm x 115.8 mm (7.5") 211.2 mm x 158.4 mm (10.4") Type LCD TFT Resolution 640 x 480 pixels Colors, displayable 64k Brightness control Yes Input device MP 277 8" Key Type Function keys MP 277 10" Key Membrane keyboard 26 function keys, 34 function keys, of which 18 with LED of which 26 with LED MP 277 188 Operating Instructions, 07/2014, A5E02479740-02 Technical specifications 10.3 Bit assignment of the direct keys Memory MP 277 8" Key Application memory MP 277 10" Key 6 MB Ports MP 277 8" Key 1 x RS 422/RS 485 2 x USB MP 277 10" Key Max. 12 Mbps USB host; conforms to USB standard 1.1 (supporting low-speed and full-speed USB devices) Maximum load 500 mA 1 x Ethernet RJ45 10/100 Mbps Supply voltage MP 277 8" Key Rated voltage MP 277 10" Key +24 V DC Range, permissible 20.4 V to 28.8 V (-15 %, +20%) Transients, maximum permissible 35 V (500 ms) Time between two transients, minimum 50 s Current consumption * Typical * Approx. 700 mA * Approx. 800 mA * Constant current, maximum * Approx. 1100 mA * Approx. 1200 mA * Power on current surge I2t * Approx. 1 A2s * Approx. 1 A2s Fuse, internal 10.3 Electronic Bit assignment of the direct keys The following figures show the assignment of the keys and LEDs to the bytes in the PLC process image. Further information may be available in your plant documentation. Note Do not use the LED bits "ACK", "A-Z l", "A-Z r" and "HELP" when a project is running on the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 189 Technical specifications 10.3 Bit assignment of the direct keys Bit assignment of the direct keys for the MP 277 8" Key Bit assignment of the direct keys for the MP 277 10" Key Bit assignment of the direct keys for the MP 277 8" Touch Bit assignment of the direct keys for the MP 277 10" Touch See also Direct keys (Page 160) MP 277 190 Operating Instructions, 07/2014, A5E02479740-02 Technical specifications 10.4 Description of the ports 10.4 Description of the ports 10.4.1 Power supply Plug connector, 2-pin Pin 10.4.2 Assignment 1 +24 VDC (L+) 2 GND 24 V (M) X10/IF 1B (RS 422/RS 485) Sub-D socket, 9-pin, with screw lock Pin 1 Assignment for the RS 422 Assignment for the RS 485 1 n. c. n. c. 2 GND 24 V GND 24 V 3 TxD+ Data channel B (+) 4 RD+ RTS 1) 5 GND 5 V, floating GND 5 V, floating 6 +5 VDC, floating +5 VDC, floating 7 +24 VDC, out (max. 100 mA) +24 VDC, out (max. 100 mA) 8 TxD- Data channel A (-) 9 RxD- RTS 1) On pin 4 or pin 9, can be set with DIP switch on the rear of the device MP 277 Operating Instructions, 07/2014, A5E02479740-02 191 Technical specifications 10.4 Description of the ports 10.4.3 X20, X21 (USB) USB socket Pin 10.4.4 Assignment 1 +5 VDC, out (max. 500 mA) 2 USB-DN 3 USB-DP 4 GND X1 (Ethernet/LAN) RJ45 plug connector Pin Assignment 1 Tx+ 2 Tx- 3 Rx+ 4 n. c. 5 n. c. 6 Rx- 7 n. c. 8 n. c. MP 277 192 Operating Instructions, 07/2014, A5E02479740-02 A Appendix A.1 Service and support You can find additional information and support for the products described on the Internet at the following addresses: Technical support (http://www.siemens.de/automation/csi_en_WW) Support request form (http://www.siemens.com/automation/support-request) After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) SIMATIC Documentation Collection (http://www.siemens.com/simatic-tech-doku-portal) Your local representative (http://www.automation.siemens.com/mcms/aspa-db/en/Pages/default.aspx) Training center (http://sitrain.automation.siemens.com/sitrainworld/?AppLang=en) Industry Mall (https://mall.industry.siemens.com) When contacting your local representative or Technical Support, please have the following information at hand: MLFB of the device BIOS version for industrial PC or image version for HMI device Other installed hardware Other installed software Tools & downloads Please check regularly if updates and hotfixes are available for download to your device. The download area is available on the Internet at the following link: After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) A.2 System events System events on the HMI device provide information about internal states of the HMI device and the controller. Note System events are only indicated if an alarm window was configured. System events are output in the language currently set on your HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 193 Appendix A.3 ESD guideline System event parameters System events may contain encrypted parameters which are relevant to troubleshooting because they provide a reference to the source code of the runtime software. These parameters are output after the text "Error code:". Description of the system events A listing of all system alarms for your HMI device is provided in the online help of your configuration software. A.3 ESD guideline Meaning An electronic module is equipped with highly integrated electronic components. Due to their design, electronic components are highly sensitive to overvoltage and thus to the discharge of static electricity. Such electronic components are labeled as electrostatic sensitive devices (ESD). The following abbreviations are commonly used for electrostatic sensitive devices: ESD ESD Electrostatic charge The damage to an ESD caused by overvoltage is usually not recognized immediately. The damage only becomes apparent after a long period of operation. NOTICE Electrostatic charge ESDs may be destroyed by voltages far below the level perceived by human beings. If you are not discharged electrostatically, the voltage that you transfer when touching a component or the contact points of a module can already cause damage. Discharge any electrostatic charge of your body before you touch the ESD. Anyone who is not connected conductively to their surroundings is subject to electrostatic charge. MP 277 194 Operating Instructions, 07/2014, A5E02479740-02 Appendix A.3 ESD guideline The following diagram shows the maximum voltage values to which a person can be charged electrostatically. The values depend on the material and humidity. The shown values are in conformity with the specifications of EN 61000-4-2. Synthetic materials Wool Antistatic materials such as wood or concrete Protective measures against discharge of static electricity NOTICE Grounding measures There is no equipotential bonding without grounding. An electrostatic charge is not discharged and may damage the ESD. When working with electrostatic sensitive devices, make sure that the person and the workplace are properly grounded. Note the following: Only touch the ESD if it is absolutely necessary. When you touch ESD modules, avoid touching the pins or the PCB tracks. This precaution reduces the risk of damaging an ESD. Discharge electrostatic electricity from your body if you are performing measurements on an ESD. To do so, touch a grounded metal object before you carry out the measurement. Always use grounded measuring instruments. MP 277 Operating Instructions, 07/2014, A5E02479740-02 195 Appendix A.3 ESD guideline MP 277 196 Operating Instructions, 07/2014, A5E02479740-02 B Abbreviations ANSI American National Standards Institution CSV Comma Separated Values DC Direct Current DHCP Dynamic Host Configuration Protocol DIL Dual-in-Line (electronic chip housing design) DNS Domain Name System DP Distributed I/O IO Input and Output ESD Components and modules endangered by electrostatic discharge EMC Electromagnetic Compatibility EN European standard ESD Components and modules endangered by electrostatic discharge GND Ground HF High Frequency HMI Human Machine Interface IEC International Electronic Commission IF Interface IP Internet Protocol LED Light Emitting Diode MAC Media Access Control MPI Multipoint Interface (SIMATIC S7) n. c. Not connected OP Operator Panel PC Personal Computer PG Programming device PPI Point-to-Point Interface (SIMATIC S7) PELV Protective Extra Low Voltage RJ45 Registered Jack Type 45 RTS Request to send RxD Receive Data PLC Programmable Logic Controller Sub-D Subminiature D (plug) TAB Tabulator TCP/IP Transmission Control Protocol/Internet Protocol TFT Thin Film Transistor TxD Transmit Data MP 277 Operating Instructions, 07/2014, A5E02479740-02 197 Abbreviations UL Underwriter's Laboratory USB Universal Serial Bus WINS Windows Internet Naming Service MP 277 198 Operating Instructions, 07/2014, A5E02479740-02 Glossary "Transfer" mode The "Transfer" operating mode is an operating mode of the HMI device in which an executable project is transferred from the configuration PC to an HMI device. Acknowledge Acknowledgment of an alarm confirms that it has been noted. Alarm logging Output of user-specific alarms to a printer, in parallel to their output to the HMI device screen. Alarm, acknowledgment Acknowledgment of an alarm confirms that it has been noted. Automation system An automation system is a PLC of the SIMATIC S7 series, for example SIMATIC S7-300 Boot loader The boot loader is used to start the operating system and is started automatically after power on of the HMI device. The loader is displayed after the operating system has loaded. Configuration PC A configuration PC is a programming device or PC on which plant projects are created using an engineering software. Configuration software Configuration software is used to create projects used for the purpose of process visualization. WinCC flexible is such a configuration software, for example. Controller PLC is a general term for devices and systems with which the HMI device communicates, e.g. SIMATIC S7. MP 277 Operating Instructions, 07/2014, A5E02479740-02 199 Glossary Degree of protection The degree of protection specifies a standard of electronic equipment for a variety of environmental conditions - and the protection of humans against potential danger when using this equipment. The degree of protection classified by IP differs from the protection class. But both involve protection against touching dangerous electric voltage. The degree of protection also classifies the protection of equipment against dirt and moisture. EMC Electromagnetic compatibility (EMC) refers to a usually desirable state, in which technical equipment does not disturb one another with unwanted electrical or electromagnetic effects. Electromagnetic compatibility deals with technical and regulatory questions of undesired, mutual influence in electrical engineering. Event Functions are triggered by defined incoming events. Events can be configured. Events which can be assigned to a button include "Press" and "Release", for example. Field Area reserved in configured screens for the input and output of values. Flash memory Flash memory is a non-volatile memory with EEPROM chips that is implemented either as mobile storage medium, or as permanently installed memory module on the motherboard. Function keys Function keys on the HMI device can be assigned user-specific functions. The functions assigned to these keys are defined during configuration. The assignment of the function keys may be specific to an active screen or independent of it. Half Brightness Life Time Time period after which brightness is reduced to 50% of the original value. The specified value depends on the operating temperature. Hardcopy Output of the screen content to a printer. MP 277 200 Operating Instructions, 07/2014, A5E02479740-02 Glossary HMI device An HMI device is a device used for the operation and monitoring of machines and plants. The machine or plant states are visualized on the HMI device by means of graphic objects or signal lamps. The operator controls of the HMI device allow the operator to interact with the processes of the machine or plant. HMI device image The HMI device image is a file that can be transferred from the configuration PC to the HMI device. The HMI device image contains the operating system for the HMI device and the elements of the runtime software required to run a project. I/O field An I/O field enables the input or output of values on the HMI device which are transferred to the PLC. Info text An info text is a configured information on objects within a project. Info text for an alarm, for example, may contain information on the cause of the fault and troubleshooting routines. Object An object is a project element such as a screen or an alarm. Objects are used to view or enter texts and values on the HMI device. Operating element An operating element is a component of a project used to enter values and trigger functions. A button, for example, is an operating element. Plant General term referring to machines, processing centers, systems, plants and processes which are operated and monitored on an HMI device. PLC job A PLC job triggers a function for the PLC on the HMI device. MP 277 Operating Instructions, 07/2014, A5E02479740-02 201 Glossary Project A project is the result of a configuration using a configuration software. The project normally contains several screens with embedded system-specific objects, basic settings and alarms. A project configured in WinCC flexible is saved to a project file with the extension *.hmi. You need to distinguish between a project on the configuration PC and an executable project on an HMI device. A project on the configuration PC can be available in more languages than can be managed on the HMI device. The project on the configuration PC can also be set up for different HMI devices. You can only transfer an executable project to an HMI device if it has been especially compiled for it. Project file A project file is a file from which the executable project file for use on the HMI device is generated. The project file is usually not transferred and is retained on the configuration PC. The file name extension of a project file is *.hmi. Project file, compressed Compressed format of the project file. The compressed project file can be transferred in addition to the executable project file to the corresponding HMI device. For this purpose, backtransfer must be enabled in the project on the configuration PC. The compressed project file is usually saved to an external memory card. A compressed project file has the extension *.pdz. Project file, executable An executable project file is the file generated from the project file for a specific HMI device. The executable project file is transferred to the associated HMI device where it is used to operate and monitor plants. An executable project file has the extension "*.fwx". Protection class The protection class is used in electrical engineering to classify and identify electrical equipment in relation to existing safety measures designed to prevent electric shock. There are four protection classes for electrical equipment. Recipe A recipe is a combination of tags that form a fixed data structure. The configured data structure can be assigned data in the configuration software or on the HMI device and is then referred to as a record. The use of recipes ensures that all data assigned to a data record is transferred synchronously to the PLC. MP 277 202 Operating Instructions, 07/2014, A5E02479740-02 Glossary Runtime software The runtime software is a process visualization software used to test a project on a configuration PC. Screen A screen is a form of visualization for all logically related process data in a plant. The representation of the process data can be visually supported by graphic objects. Screen object A screen object refers to objects such as rectangles, I/O fields, or alarm views which are configured for visualization or operation of the plant. STEP 7 STEP 7 is the programming software for SIMATIC S7, SIMATIC C7 and SIMATIC WinAC PLCs. Symbolic I/O field A symbolic I/O field is a field for the input and output of a value. Contains a list of default entries from which one can be selected. System alarm A system alarm is assigned to the "System" alarm class. A system alarm refers to internal states on the HMI device and the PLC. Tab order The tab order defined in the course of project engineering determines the sequence for activating objects by pressing the key. Tag A tag is a defined memory location to which values can be written and from which values can be read. This can be done from the PLC or the HMI device. We distinguish between external tags (process tags) and internal tags, depending on whether or not the tag is interconnected with the PLC. MP 277 Operating Instructions, 07/2014, A5E02479740-02 203 Glossary Transfer Transfer of a runtime project from the configuration PC to the HMI device. WinAC MP WinAC is a software PLC for multifunctional platforms. MP 277 204 Operating Instructions, 07/2014, A5E02479740-02 Index / /Audit, 21 A ACK key, 172 Acknowledge Alarm, 172 Acknowledge key, 172 Acoustic feedback, 160 Acoustic signal, 165 Inadvertent operation, 160 Acoustics Feedback, 97 Activate Password protection, 89 Address assignment TCP/IP network, 116 Addressing, 114 Alarm Acknowledge, 172 Functional scope, 19 Alarm buffer Functional scope, 19 ALARM_S, 19 Alphanumerical Key assignment, 83, 172 Screen keyboard, 166 Alphanumerical value Changing, 167, 176 Entering, 167, 176 ALT key, 83, 172 Applications MP 277, 9 Approval for Australia, 29 Approvals, 27 Automatic Transfer, 143 A-Z key, 83, 172 B Backing up, 136, 147, 148 Registry information, 76, 92 Temporary files, 92 to external storage device, 126 To memory card, 76 With ProSave, 148 Backlighting Reducing, 95 Setting, 77 Backspace key, 82, 171 Backtransfer, 141, 145 Backup, 76, 128 Booting, 99 Bottom view, 10, 12, 13, 15 Brightness Changing, 94 Browser Home page, 76 Setting, 76 Bus connection, 22 Bus parameters Profile, 108 C Cable Connecting, 45 Calibrating Touch screen, 87 Cancel key, 82, 171 Care, 181 CE approval, 27 Certificate Delete, 125 Deleting, 76 Displaying, 76 Importing, 76, 125 Certificates, 76 Changing Brightness, 94 Character repeat, 76 Screen keyboard, 85 Charge Electrostatic, 194 Clamping frame, 17 Clean screen, 182 Clearance MP 277, 39 Climatic Shipping conditions, 33 Storage conditions, 33 MP 277 Operating Instructions, 07/2014, A5E02479740-02 205 Index Closing Project, 179 Compatibility conflict, 147 Computer name Setting, 77 Condensation, 33 Conductor cross-section, 48 Equipotential bonding, 46 Configuration graphic Configuration PC, 53 Controller, 50 Equipotential bonding, 47 Power supply, 48 Printer, 57 Configuration PC Configuration graphic, 53 Connecting, 53 Configuration phase, 133 Configure Network, 114 Configuring Data channel, 77, 109 Operating system, 70 PC/PPI cable, 54 RS 422/RS 485 interface, 51 Screen keyboard, 76, 84 Configuring PC, 133 Connecting Configuration PC, 53 Controller, 50 Equipotential bonding, 46 Mains terminal, 49 Power supply, 48, 49 Printer, 57 PROFINET, 51, 53 USB device, 56 Connection, 22 Connection sequence, 45 Connections to PLCs Number, 22 Control cabinet Working on, 25 Control keys Keyboard unit, 81 Control Panel MPI, 107 Open, 75 Operating, 78, 80 Password protection, 71 PROFIBUS, 107 Screen keyboard, 78 Control Panel:Operate, 77 Controller Configuration graphic, 50 Configuring the interface, 51 Connecting, 50 Conventions, 4 Converter RS 422-RS 232, 16 Cookies, 123 CTRL key, 83, 172 Currency, 77 Cursor key, 82, 170 D Data channel Configuring, 77, 109 Enabling, 109 Locking, 109 Data transfer, 136 Date, 76 Entering, 168, 177 Setting, 90 Synchronizing, 91 Date format, 77, 92 Date/time properties, 76, 90 Deactivating Password protection, 90 Decimal, 164 Default gateway, 116 Degree of protection, 38 Protection against ingress of solid foreign bodies, 40 Protection against water, 40 Delay time Setting, 77, 103 Delete Certificate, 125 Delete key, 82, 82, 171, 171 Device name For network operation, 115 DHCP, 116 DIP switch Setting, 51 Direct key, 161 Functional scope, 21 Direct keys Assignment, 189 Disabling SecureMode, 74 Display MP 277 Key, 188 MP 277 Touch, 187 Display format, 174 MP 277 206 Operating Instructions, 07/2014, A5E02479740-02 Index Displaying Certificate, 76 HMI device information, 76 Info text, 169, 178 Information on the MP 277, 100 Memory information, 101 System information, 101 UPS status, 77 Disposal, 182 Disturbance Pulse-shaped, 31 Sinusoidal, 32 DNS, 116 DNS Server, 114 Documentation Enclosed, 41 Double-click, 76 Setting, 86 E EC Declaration of Conformity, 27 Elbow adapter, 17 Electrical Safe separation, 49 Electrical potential difference, 46 Electrostatic charge, 194 E-mail Set, function overview, 77 Setting, 119 EMC directive, 27 Emission, 30, 32 Enabling SecureMode, 74 Encryption, 123 END key, 82, 171 Enter key, 82, 171 ENTER key, 82, 171 Entering Alphanumerical value, 167, 176 Date, 168, 177 Key combination, 83, 172 Numerical value, 165, 175 Symbolic value, 168 Text box, 163 Time, 168, 177 Entry on the HMI device By means of function key, 173 Using operating elements, 157 Environmental conditions Climatic, 36 Mechanical, 35 Test, 36 Equipotential bonding Cable, 47 Configuration graphic, 47 Connecting, 46 Requirements, 46 Equipotential bonding rail, 47 ESC key, 82, 171 Ethernet settings IP address, 116 F Feedback Acoustic, 97, 160 Optical, 159 Fixation, 16 FM approval, 29 Fn key, 83, 172 Front view, 10, 11, 13, 14 Function Additional, 21 Function key Labeling, 65 Function keys Global assignment, 173 Local assignment, 173 Function test, 59 Functional scope Alarm buffer, 19 ALARM_S, 19 Graphics list, 19 Info text, 21 Limit monitoring, 19 Log, 20 Messages, Recipe, 20 Safety, 20 Scaling, 19 Screen, 19 Tag, 19 Text list, 19 G Graphics list Functional scope, 19 Group acknowledgement, 172 Guidelines for Explosion Protection, 28 MP 277 Operating Instructions, 07/2014, A5E02479740-02 207 Index H High frequency radiation, 26 HMI device Cold restart, 99 EMC-compatible installation, 31 Information, 76 Interfaces, 45 Restarting, 76 Shutting down, 59 Specifications, 186, 188 Switching on, 58 Testing, 58 Transfer license key, 154 HMI Input Panel Options, 84 HOME key, 82, 171 Home page Internet, 121 Host cable Safety instruction, 55 I Identification, 118 Importing Certificate, 76, 125 Inadvertent operation Acoustic signal, 160 Info text Displaying, 169, 178 Functional scope, 21 Key, 172 LED, 172 Information For the HMI device, 100 Initial startup, 133 Input device MP 277 Key, 188 MP 277 Touch, 187 Input Panel, 76 Installation as intended, 26 Installing Option, 136, 152, 152 Instructions General, 30 Insulation test Test voltage, 40 Interfaces MP 277, 45 Rated load, 56 Internet Home page, 121 Options, 76 Search engine, 121 Security settings, 76 Settings, 119 Settings, overview of functions, 77 Internet options Privacy, 124 IP address Ethernet, 116 K Key ACK, 172 ALT, 83, 172 A-Z, 83, 172 Backspace, 171 Cancel, 82 CTRL, 83, 172 Cursor, 82, 170 Delete, 82, 82, 171 END, 82, 171 ENTER, 82, 171 ESC, 82, 171 Fn, 83, 172 HOME, 82, 171 Info text, 172 Scroll back, 82, 171 Scroll forward, 82, 171 SHIFT, 83, 172 TAB, 82, 170 Tabulator, 82 Key combination Entering, 83, 172 Key control, 170, 174 Keyboard Safety instruction, 62 Keyboard properties, 76 L Labeling Approvals, 29 EC Declaration of Conformity, 27 Function key, 65 Guidelines for Explosion Protection, 28 Labeling strips Attaching, 67 Dimensions, 66 MP 277 208 Operating Instructions, 07/2014, A5E02479740-02 Index LAN connection, 76 Language switching Functional scope, 21 LED Info text, 172 License Managing, 154 License key Transfer to an HMI device, 154 Transferring, 136 Transferring back, 136 Limit monitoring Functional scope, 19 Limit test, 164 Limit value test, 174 Loader, 70 Operating, 71 Locking Operating element, 182 Log Functional scope, 20 Logon data, 118 M Main dimensions MP 277 10" Touch, 185 MP 277 8" Key, 184 MP 277 8" Touch, 183 Mains terminal Connecting, 49 Maintenance, 181 Managing License, 154 Manual Transfer, 142 Mechanical Shipping conditions, 33 Storage conditions, 33 Memory MP 277 Key, 189 MP 277 Touch, 187 Memory card First time use, 127 Inserting, 64 Restoring file system, 93 Unplug, 65 Memory information Displaying, 101 Memory management, 76, 131 Mounting EMC-compatible, 31 Mounting clip, 42, 43, 44 Mounting clip, 16 Mounting, 42, 43, 44 Mounting cut-out Dimensions, 39 Preparing, 39 Mounting location, 38 Mounting position, 37 Mouse properties, 76 MP 277 Applications, 9 Clearance, 39 Displaying information, 100 Interfaces, 45 Mounting, 41 Operator control, 61 Switching on, 58 Testing, 58 MP 277 10" Key Bottom view, 15 Front view, 14 Overall dimensions, 186 Rear view, 15 Side view, 14 MP 277 10" Touch Bottom view, 13 Front view, 13 Main dimensions, 185 Rear view, 14 Side view, 13 MP 277 8" Key Bottom view, 12 Front view, 11 Main dimensions, 184 Rear view, 12 Side view, 11 MP 277 8" Touch Bottom view, 10 Front view, 10 Main dimensions, 183 Rear view, 11 Side view, 10 MP 277 Key Specifications, 188 MPI Setting, 77, 107 Multi-key operation, 158, 170 Multimedia card, 63 MP 277 Operating Instructions, 07/2014, A5E02479740-02 209 Index N Name server, 116 Network Configure, 114 Logon data, 76 Set up, 114 Setting, 116 Network & dial-up connections, 76 Network ID, 76 Network operation Device name, 115 Options, 77, 119 Nominal voltage, 40 Non-isolated plant configuration, 49 NOTE License key, 152 Number format, 77, 92 Numerical Key assignment, 83, 172 Screen keyboard, 163 Numerical value Changing, 165, 175 Decimal places, 164, 164 Display format, 174 Entering, 165, 175 Limit test, 164 Limit value test, 174 O Offline Operating mode, 134 Test, 140, 146 Online Operating mode, 134 Test, 141, 146 OP properties, 76 Device, 100 Memory monitoring, 131 Persistent storage, 93 Touch, 87 OPC server, 21 Open Control Panel, 75 Selection list, 82, 171 Operate:Control Panel, 77 Operating Control Panel, 78 Feedback, 159 Key, 170, 174 Loader, 71 Operating element, 82, 171 Project, 157 With external keyboard, 158 With external mouse, 158 Operating element Locking, 182 Operating, 82, 171 Selecting, 82 Operating instructions Scope, 3 Operating mode, 134 Changing, 134 Offline, 134 Online, 134 Transfer, 58, 134 Operating system Configuring, 70 Safety instruction, 55 Update using ProSave, 151 Updating, 149 Operation feedback, 159 Operator control Memory card slot, 64 MP 277, 61 Optical feedback, 159 Option Installing, 136, 152 Installing with ProSave, 152 Removing, 136, 152 Removing with ProSave, 153 Options, 21 Network operation, 77, 119 Overall dimensions MP 277 10" Key, 186 P Password Specifying, 89 Password properties, 76, 89, 89 Password protection, 71, 76 Activate, 89 Deactivating, 90 Windows CE taskbar, 71 PC/PPI Cable, 17 Configuring the cable, 54 Setting the adapter, 54 PELV, 49 Peripheral Rated load, 56 MP 277 210 Operating Instructions, 07/2014, A5E02479740-02 Index Plant configuration Non-insolated, 49 PLC Number of connectable, 22 Protocol, 22 Ports MP 277 Key, 189 MP 277 Touch, 187 Power failure, 147 Power supply Configuration graphic, 48 Connecting, 48, 49 Printer Configuration graphic, 57 Connecting, 57 Setting properties, 76 Printer connection Setting, 96 Printer properties, 76, 96 Printing Via network printer, 113 Process control phase, 133 PROFIBUS Setting, 77 PROFIBUS DP Setting, 107 PROFINET, 114 Addressing, 114 Connecting, 51, 53 PROFINET IO Disabling direct keys, 112 Enabling direct keys, 112 Releasing, 76 Project Closing, 179 in ProTool, 135 In WinCC flexible, 135 Offline testing, 140, 146 Operating, 157 Reuse, 135, 135, 135 Testing online, 141, 146 Transferring, 133, 136 Protection class, 40 Protective measure Static electricity, 195 Protocol PLC, 22 Proxy Server, 76, 119, 122 Setting, 76 R Radiation High frequency, 26 Radio interference, 30 Emission, 32 Rated load Interface, 56 Rear view, 11, 12, 14, 15 Recipe Functional scope, 20 Recommissioning, 133 Recycling, 182 Regional and language settings, 77, 92 Regional settings, 92 Registry information Backing up, 76, 92 Regulations for the prevention of accidents, 25 Removing Option, 136, 152, 153 Repairs, 182 Reset to factory setting, 136 Resetting to factory settings, 151 Restore, 76, 126 Restoring, 136, 147, 148 from external storage device, 128 From memory card, 76, 93 With ProSave, 148 Returns Center, 182 Reverse polarity protection, 49 RS 422/RS 485 interface Configuring, 51 S S7 transfer settings, 77 Safe electrical isolation, 49 Safety Functional scope, 20 Standards, 27 Safety instruction Backlighting, 95 Compatibility conflict, 147 Compressed project file, 141 Damage to the HMI device, 45 Data channel, 150 Direct key, 160 Equipotential bonding cable, 47 Functional problem, 56 High frequency radiation, 26 Interface, 56 Keyboard, 62 MP 277 Operating Instructions, 07/2014, A5E02479740-02 211 Index License key, 147, 150 Memory card, first use, 64 Memory distribution, 101 Multi-key operation, 158 Power failure, 147 Preventing inadvertent operation, 181 Replacing the HMI device, 55 Storage, 33 Switching info text, 169, 178 Touch screen, 62 Transfer mode, 106, 109 Transfer mode channel 2, 110 Transport, 33 Unintentional action, 62, 170 Unintentional transfer mode, 110 Update operating system, 55 USB host-to-host cable, 55 Working on the control cabinet, 25 Safety regulations, 25 Scaling Functional scope, 19 Scheduler Functional scope, 21 Screen Functional scope, 19 Screen keyboard, 76, 162 Alphanumerical, 166 Change layout, 79 Character repeat, 85 Configuring, 84 For Control Panel, 78 Keyboard level, 166 Language switching, 166 Numeric, 163 Representation types, 79 Screen saver, 95 Overview of functions, 77, 77 Setting, 95 Screen settings Changing, 76 Scroll back key, 82, 171 Scroll forward key, 82, 171 Search engine Internet, 121 SecureMode Disabling, 74 Enabling, 74 Security settings, 76 Selecting Operating element, 82 Selection list, 168, 177 Open, 82, 171 Service pack, 17 Set up Network, 114 Setting Backlighting, 77 Browser, 76 Computer name, 77 Date, 90 Date format, 92 Date/Time, 76 Delay time, 77, 103 DIP switch, 51 Double-click, 86 E-mail, 77 E-mail connection, 119 Language, 161 MPI, 77, 107 Network, 116 Number format, 92 PC/PPI adapter, 54 Printer connection, 96 Printer properties, 76 PROFIBUS, 77, 107 PROFINET IO, 76 Proxy, 76 Regional data, 92 Screen saver, 95 Time, 90 Time format, 92 Transfer mode, 138 UPS, 77, 104, 104 Volume, 77 Setting language, 161 Setting the time zone, 90 Settings Internet, 77 Language, 77 Regional, 77 S7-Transfer, 77 Shift key, 83 SHIFT key, 83, 172 Shipping conditions, 33 Shutting down HMI device, 59 Side view, 10, 11, 13, 14 Siemens HMI input panel options, 76 Sm@rtAccess, 21 Sm@rtService, 21 SMTP server, 119 Software options, 21 Specifications Display, 187, 188 MP 277 212 Operating Instructions, 07/2014, A5E02479740-02 Index Input device, 187, 188 Memory, 187, 189 MP 277 Key, 188 MP 277 Touch, 186, 188 Ports, 187, 189 Supply voltage, 187, 189 Standard operating system, 9 Start HMI device, 99 Transfer, 139 Static electricity Protective measures, 195 Storage conditions, 33 Storage device Backing up to external, 126 Restoring from external, 128 Strain relief, 59 Subnet mask, 116 Supply voltage MP 277 Key, 189 MP 277 Touch, 187 Switching on MP 277, 58 Symbolic value Changing, 168 Entering, 168 Synchronizing Date and time, 91 System, 101 System event in the online help, 194 Parameters, 194 System information, 77 Displaying, 101 System properties, 77 Device name, 115 General, 101 Memory, 101 Text box, 163 Character mode, 171 Normal mode, 171 Text list Functional scope, 19 Time, 76 Entering, 168, 177 Setting, 90 Synchronizing, 91 Time format, 77, 92 Touch screen Calibrating, 76, 87 Safety instruction, 62 Transfer, 133, 134, 137, 141 Automatic, 143 Cancel, 58 Manual, 142 Start, 139 Starting automatically, 137 Starting manually, 137 Transfer mode Setting, 138 Unintentional, 110 Via MPI, 106 Via PROFIBUS DP, 106 Transfer settings, 109 Channel, 109 Directories, 103 Overview of functions, 77 Transferring License key, 136 License key on HMI device, 154 Project, 133, 136 Transferring back License key, 136 Transport damage, 41 Trends Functional scope, 21 T U TAB key, 82, 170 Tabulator key, 82, 170 Tag Functional scope, 19 TCP/IP address, 116 Temporary files Backing up, 92 Test For environmental conditions, 36 Testing MP 277, 58 UL approval, 29 Unintentional action, 62, 158 Unintentional transfer mode, 110 Update operating system, 136 Updating Operating system, 149 Using ProSave, 151 UPS Displaying status, 77 Setting, 77, 104, 104 MP 277 Operating Instructions, 07/2014, A5E02479740-02 213 Index UPS properties Configuration, 104, 104 Current status, 105, 105, 105, 105 USB device Connecting, 56 Use Conditions, 35 In residential areas, 30 Industrial, 30 With additional measures, 35 User name, 118, 118 V VBScript Functional scope, 21 Volume, 97, 97 Setting, 77 Volume & Sounds Properties, 77 W Weight MP 277 Key, 188 Weight of the MP 277 Touch, 186 WinCC flexible Internet Settings, 77 WinCC flexible internet settings E-mail, 119 Windows CE taskbar, 70 Password protection, 71 WINS, 116 Server, 114 Working on the control cabinet, 25 MP 277 214 Operating Instructions, 07/2014, A5E02479740-02