Original Creation Date: 10/30/95
Last Update Date: 08/28/96
Last Major Revision Date: 08/21/96
MN100314-X REV 1A0 MILITARY DATA SHEET
LOW POWER QUINT DIFFERENTIAL LINE RECEIVER
General Description
The 100314 is a monolithic quint differential line receiver with emitter-follower
outputs. An internal reference supply (Vbb) is available for single-ended reception.
When used in single-ended operation, the only mode allowed is to connect the complementary
inputs to Vbb. Unlike other F100K ECL devices, the inputs do not have input pull-down
resistors. Active current sources provide common-mode rejection of 1.0V in either the
positive or negative direction. A defined output state exists if both inverting and
non-inverting inputs are at the same potential between Vee and Vcc. The defined state is
logic HIGH on the Oa-Oe outputs.
NS Part Numbers
100314DMQB
100314FMQB
100314J-QMLV
100314W-QMLV
Industry Part Number
100314
Prime Die
F314
Processing
MIL-STD-883, Method 5004
Quality Conformance Inspection
MIL-STD-883, Method 5005
Subgrp Description Temp ( C)
o
1 Static tests at +25
2 Static tests at +125
3 Static tests at -55
4 Dynamic tests at +25
5 Dynamic tests at +125
6 Dynamic tests at -55
7 Functional tests at +25
8A Functional tests at +125
8B Functional tests at -55
9 Switching tests at +25
10 Switching tests at +125
11 Switching tests at -55
1
MILITARY DATA SHEET
MN100314-X REV 1A0
Features
- 35% power reduction of the F100114
- 2000V ESD protection
- Pin/function compatible with 100114
- Voltage compensated operating range = -4.2V to -5.7V
- Available to MIL-STD-883
- Available to industrial grade temperature range
2
MILITARY DATA SHEET
MN100314-X REV 1A0
(Absolute Maximum Ratings)
(Note 1)
Storage Temperature (Tstg) -65 C to +150 C
Maximum Junction Temperature (Tj) +175 CCeramic +150 CPlastic
Vee Pin Potential to Ground Pin -7.0V to +0.5V
Input Voltage (DC) Vee to +0.5V
Output Current (DC Output HIGH) -50mA
ESD
(Note 2) > 2000V
Note 1: Absolute maximum ratings are those values beyond which the device may be damaged or
have its useful life impaired. Functional operation under these conditions is not
implied.
Note 2: ESD testing conforms to MIL-STD-883, Method 3015.
Recommended Operating Conditions
Case Temperature (Tc) 0 C to +85 CCommercial -55 C to +125 CMilitary -40 C to +85 CIndustrial
Supply Voltage (Vee) -5.7V to -4.2V
3
MN100314-X REV 1A0 MILITARY DATA SHEET
Electrical Characteristics
DC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: Vee Range: -4.2V to -5.7V, Tc= -55C to +125C, VCC=VCCA=GND
SYMBOL PARAMETER CONDITIONS NOTES PIN-
NAME MIN MAX UNIT SUB-
GROUPS
IIH Input HIGH
Current Vee= -5.7V, VM= -0.87V 1, 3 INPUTS 50 uA 1, 2
1, 3 INPUTS 70 uA 3
ICBO Input Leakage
Current Vee= -4.2V, VM= -4.2V 1, 3 INPUTS -10 uA 1, 2,
3
VOH Output HIGH
Voltage Vee=-4.2V/-5.7V, VIH=-0.87V,
VIL=-1.83V, LOADING: 50 Ohms To -2.0V 1, 3 OUTPUTS -1025 -870 mV 1, 2
1, 3 OUTPUTS -1085 -870 mV 3
VOL Output LOW
Voltage Vee=-4.2V/-5.7V, VIH=-0.87V,
VIL=-1.83V, LOADING: 50 Ohms to -2.0V 1, 3 OUTPUTS -1830 -1620 mV 1, 2
1, 3 OUTPUTS -1830 -1555 mV 3
VOHC Output HIGH
Voltage Vee=-4.2V/-5.7V, VIH=-1.165V,
VIL=-1.475V, LOADING: 50 Ohms to -2.0V 1, 3 OUTPUTS -1035 mV 1, 2
1, 3 OUTPUTS -1085 mV 3
VOLC Output LOW
Voltage Vee=-4.2V/-5.7V, VIH=-1.165V,
VIL=-1.475V, LOADING:50 Ohms to -2.0V 1, 3 OUTPUTS -1610 mV 1, 2
1, 3 OUTPUTS -1555 mV 3
VBBX Output Reference
Voltage Vee=-4.2V, IM=0uA 1, 3 VBB -1260 mV 1, 2,
3
VBBN Output Reference
Voltage Vee=-5.7V, IM=-250uA 1, 3 VBB -1380 mV 1, 2
Vee=-5.7V, IM=-350uA 1, 3 VBB -1396 mV 3
VIH Input HIGH
Voltage Dn AT VBB 1,
3, 7 Dn -1165 -870 mV 1, 2,
3
VIL Input LOW Voltage Dn AT VBB 1,
3, 7 Dn -1830 -1475 mV 1, 2,
3
VCM Common Mode
Voltage VEE= -4.2/-5.7V 1,
3, 7 INPUTS -2000 -500 mV 1, 2,
3
VDIFF Input Voltage
Differential VEE= -4.2/-5.7V 1,
3, 7 INPUTS 150 mV 1, 2,
3
IEE Power Supply
Current Vee= -4.2/-5.7V, VIN=VBB 1, 3 VEE -65 -25 mA 1, 2,
3
4
MN100314-X REV 1A0 MILITARY DATA SHEET
Electrical Characteristics
AC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: Vee Range: -4.2V to -5.7V, VCC=VCCA=GND, LOADING: 50 Ohms To -2.0V
SYMBOL PARAMETER CONDITIONS NOTES PIN-
NAME MIN MAX UNIT SUB-
GROUPS
tPLH/tPHL Propagation Delay Vee= -4.2/-5.7V 2, 4 Dn/Dn t
o On/On 0.6 2.2 ns 9
2, 4 Dn/Dn t
o On/On 0.6 2.7 ns 10
2, 4 Dn/Dn t
o On/On 0.4 2.3 ns 11
tTLH/tTHL Transition Time Vee= -4.2/-5.7V 6 On/On 0.2 1.4 ns 9, 10,
11
Note 1: Screen tested 100% on each device at -55 C, +25 C and +125 C temp., subgroups 1, 2,
3, 7 & 8.
Note 2: For QB devices, screen tested 100% on each device at +25C temperature only, subgroup
A9. For QMLV devices, screen tested 100% on each device at +25C, +125C & -55C
temperature, subgroups A9, 10 & 11.
Note 3: Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, +125 C & -55 C temp.,
subgroups A1, 2, 3, 7 & 8.
Note 4: Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, subgroup A9, and at
+125 C & -55 C temp., subgroups A10 & 11.
Note 5: Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C temp. only, subgroup
A9.
Note 6: Not tested at +25 C, +125 C & -55 C temp. (DESIGN CHARACTERIZATION DATA).
Note 7: Guaranteed by applying specified input condition and testing VOH/VOL.
5
MILITARY DATA SHEET
MN100314-X REV 1A0
Graphics and Diagrams
GRAPHICS# DESCRIPTION
J24ERJ CERDIP(J), 24LD .400 CENTERS (P/P DWG)
P000043A CERDIP (J), 24LD .400 CENTERS (PIN OUT)
P000044A CERPAC, QUAD, 24 LEAD (PIN OUT)
W24BRE CERPAC, QUAD, 24 LEAD (P/P DWG)
See attached graphics following this page.
6
