SM6TY Automotive 600 W TransilTM Datasheet - production data Features Peak pulse power: - 600 W (10/1000 s) - 4 kW (8/20 s) A Stand-off voltage range: from 6 V to 70 V Unidirectional and bidirectional types Low leakage current: - 0.2 A at 25 C - 1 A at 85 C Operating Tj max: 150 C High power capability at Tj max: - 515 W (10/1000 s) JEDEC registered package outline Resin meets UL 94, V0 AEC-Q101 qualified K Bidirectional SMB (JEDEC DO-214AA) Unidirectional Description Complies with the following standards ISO 10605, C = 150 pF, R = 330 : - 30 kV (air discharge) - 30 kV (contact discharge) ISO 10605, C = 330 pF, R = 330 : - 30 kV (air discharge) - 30 kV (contact discharge) ISO 7637-2(a) - Pulse 1: VS = -100 V - Pulse 2a: VS = +50 V - Pulse 3a: VS = -150 V - Pulse 3b: VS = +100 V The planar technology makes this device compatible with high-end circuits where low leakage current and high junction temperature are required to provide reliability and stability over time. SM6TY are packaged in SMB (SMB footprint in accordance with IPC 7531 standard). a. Not applicable to parts with stand-off voltage lower than the average battery voltage (13.5 V) March 2012 This is information on a product in full production. The SM6TY Transil series has been designed to protect sensitive automotive circuits against surges defined in ISO 7637-2 and against electrostatic discharges according ISO 10605. TM: Transil is a trademark of STMicroelectronics Doc ID 17741 Rev 3 1/12 www.st.com 12 Characteristics SM6TY 1 Characteristics Table 1. Absolute maximum ratings (Tamb = 25 C) Symbol VPP PPP Tj Tstg TL Parameter Peak pulse voltage Value ISO 10605 (C = 330 pF, R = 330 ): Contact discharge Air discharge ISO 10605 (C = 150 pF, R = 330 ): Contact discharge Air discharge Peak pulse power dissipation(1) Unit 30 30 kV 30 30 Tj initial = Tamb 600 W Operating junction temperature range -55 to 150 Storage temperature range -65 to 150 Maximum lead temperature for soldering during 10 s. C 260 1. For a surge greater than the maximum values, the diode will fail in short-circuit. Figure 1. Electrical characteristics - definitions Symbol VRM VBR VCL IRM IPP T VF RD Figure 2. Parameter Stand-off voltage Breakdown voltage Clamping voltage Leakage current @ VRM Peak pulse current Voltage temperature coefficient Forward voltage drop Dynamic resistance Unidirectional I I IF IPP VF VCL VBR VRM V V IRM IR IPP IPP Repetitive pulse current tr = rise time (s) tp = pulse duration time (s) 2/12 IR IRM IRM IR Pulse definition for electrical characteristics tr VCLVBR VRM tp Doc ID 17741 Rev 3 VRMVBR VCL Bidirectional SM6TY Table 2. Characteristics Electrical characteristics, parameter values (Tamb = 25 C) IRM max @ VRM Order code 25 C 85 C A VCL @ IPP RD (2) VCL @ IPP RD (2) 10/1000 s 10/1000 s 8/20 s 8/20 s VBR @IR (1) min. typ. max. V V max. max. T max. mA V(3) A(4) V(3) A(4) 10-4/ C SM6T6V8AY/CAY 20 50 5.80 6.45 6.80 7.10 10 10.5 57.0 0.059 13.4 298 0.021 5.70 SM6T7V5AY/CAY 20 50 6.40 7.13 7.50 7.90 10 11.3 53.0 0.065 14.5 276 0.024 6.10 SM6T10AY/CAY 20 50 8.55 9.50 10.0 10.5 1 14.5 41.0 0.098 18.6 215 0.038 7.30 SM6T12AY/CAY 0.2 1 10.2 11.4 12.0 12.6 1 16.7 36.0 0.114 21.7 184 0.049 7.80 SM6T15AY/CAY 0.2 1 12.8 14.3 15.0 15.8 1 21.2 28v 0.193 27.2 147 0.078 8.40 SM6T18AY/CAY 0.2 1 15.3 17.1 18.0 18.9 1 25.2 24.0 0.263 32.5 123 0.111 8.80 SM6T22AY/CAY 0.2 1 18.8 20.9 22.0 23.1 1 30.6 20.0 0.375 39.3 102 0.159 9.20 SM6T24AY/CAY 0.2 1 20.5 22.8 24.0 25.2 1 33.2 18.0 0.444 42.8 93.0 0.189 9.40 SM6T27AY/CAY 0.2 1 23.1 25.7 27.0 28.4 1 37.5 16.0 0.569 48.3 83.0 0.240 9.60 SM6T30AY/CAY 0.2 1 25.6 28.5 30.0 31.5 1 41.5 14.5 0.69 53.5 75.0 0.293 9.70 SM6T33AY/CAY 0.2 1 28.2 31.4 33.0 34.7 1 45.7 13.1 0.84 59.0 68.0 0.357 9.80 SM6T36AY/CAY 0.2 1 30.8 34.2 36.0 37.8 1 49.9 12.0 1.01 64.3 62.0 0.427 9.90 SM6T39AY/CAY 0.2 1 33.3 37.1 39.0 41.0 1 53.9 11.1 1.16 69.7 57.0 0.504 10.0 SM6T42AY/CAY 0.2 1 36.0 40.0 42.1 44.2 1 58.1 10.3 1.35 76.0 52.0 0.611 10.0 SM6T47AY/CAY 0.2 1 40.0 44.4 46.7 49.0 1 64.5 9.7 1.59 84.0 48.0 0.728 10.1 SM6T56AY/CAY 0.2 1 47.6 53.2 56.0 58.8 1 76.6 7.8 2.28 100 40.0 1.03 10.0 SM6T68AY/CAY 0.2 1 58.1 64.6 68.0 71.4 1 92 6.5 3.17 121 33.0 1.50 10.4 SM6T75AY/CAY 0.2 1 64.1 71.3 75.0 78.8 1 103 5.8 4.17 134 30.0 1.84 10.5 SM6T82AY/CAY 0.2 1 70.0 77.8 81.9 86.0 1 113 5.5 4.91 146 27.0 2.22 10.5 1. Pulse test: tp < 50 ms 2. To calculate maximum clamping voltage at another surge level, use the following formula: VCLmax = VCL - RD x (IPP - IPPappli) where IPPappli is the surge current in the application. 3. To calculate VBR or VCL versus junction temperature, use the following formulas: VBR @ TJ = VBR @ 25C x (1 + T x (TJ - 25)) VCL @ TJ = VCL @ 25C x (1 + T x (TJ - 25)) 4. Surge capability given for both directions for unidirectional and bidirectional types. Doc ID 17741 Rev 3 3/12 Characteristics Figure 3. SM6TY Figure 4. Peak power dissipation versus initial junction temperature (typical values) Ppp (W) Peak pulse power versus exponential pulse duration PPP(kW) 700 100.0 10/1000 s Tj initial = 25 C 600 500 10.0 400 300 1.0 200 100 Tj(C) tP(ms) 0.1 0 0 25 Figure 5. 1000.0 50 75 100 125 150 1.0E-03 175 1.0E-02 1.0E-01 1.0E+00 1.0E+01 Clamping voltage versus peak pulse current exponential waveform (maximum values) IPP (A) Tj initial = 25 C 100.0 8/20 s 10.0 1 10 SM6T82AY/CAY 0.1 SM6T30AY/CAY SM6T6V8AY/CAY 1.0 4/12 10/1000 s VCL(V) 100 Doc ID 17741 Rev 3 1000 SM6TY Characteristics Figure 6. 10 ISO 7637-2 pulse 1 response (VS = -100 V) Voltage (V) 0 -10 -20 -30 -40 SM6T36AY -50 SM6T36CAY Current (A) 0 -2 -4 -6 -8 -10 -12 Time (ms) 1.0 0.0 Figure 7. 2.0 3.0 4.0 ISO 7637-2 pulse 2a response (VS = 50 V) Voltage (V) 50 40 30 20 10 0 12 SM6T36AY Current (A) SM6T36CAY 10 Note: Curves superimposed 8 6 4 2 0 Time (s) 0 20 30 40 50 60 Doc ID 17741 Rev 3 70 80 90 100 5/12 Characteristics Figure 8. SM6TY ISO 7637-2 pulse 3a response (VS = -150 V) 20 Voltage (V) 10 0 -10 -20 -30 -40 SM6T36AY -50 SM6T36CAY 0.5 Current (A) 0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 Time (s) 0 Figure 9. 60 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 ISO 7637-2 pulse 3b response (VS = 100 V) Voltage (V) 50 40 30 20 10 0 Current (A) SM6T36AY 3.0 SM6T36CAY 2.5 Note: Curves superimposed 2.0 1.5 1.0 0.5 0 Time (s) 0 Note: 6/12 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 ISO7637-2 pulses responses are not applicable for products with a stand off voltage lower than the average battery voltage (13.5 V). Doc ID 17741 Rev 3 SM6TY Characteristics Figure 10. Junction capacitance versus reverse Figure 11. Junction capacitance versus applied voltage for unidirectional reverse applied voltage for types (typical values) bidirectional types (typical values) 10000 C(pF) C(pF) 10000 F = 1 Mhz VOSC = 30 mVRMS Tj = 25 C F = 1 Mhz VOSC = 30 mVRMS Tj = 25 C SM6T6V8AY 1000 SM6T6V8CAY 1000 SM6T30AY 100 SM6T30CAY SM6T82AY VR(V) 10 1 10 100 Figure 12. Relative variation of thermal impedance, junction to ambient, versus pulse duration 1.00 1 1000 VR(V) SM6T82CAY 100 10 100 1000 Figure 13. Thermal resistance junction to ambient versus copper surface under each lead Rth(j-a) (C/W) Zth (j-a)/Rth (j-a) 110 Recommended pad layout Printed circuit board FR4, copper thickness = 35 m 100 Printed circuit board FR4, copper thickness = 35 m 90 80 70 60 0.10 50 40 30 20 tp s 10 0.01 SCu(cm) 0 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Figure 14. Leakage current versus junction temperature (typical values) IR (nA) 0.0 0.5 VR=VRM VRM < 10 V 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Figure 15. Peak forward voltage drop versus peak forward current (typical values) 1.0E+02 1.E+03 1.0 1.E+02 1.0E+01 1.E+01 1.0E+00 IFM(A) Tj =125 C Tj =25 C VR=VRM VRM 10 V 1.E+00 1.0E-01 Tj ( C) VFM(V) 1.E-01 1.0E-02 25 50 75 100 125 150 0.0 Doc ID 17741 Rev 3 0.5 1.0 1.5 2.0 2.5 3.0 7/12 Application and design guidelines 2 SM6TY Application and design guidelines More information is available in the ST Application note AN2689 "Protection of automotive electronics from electrical hazards, guidelines for design and component selection". 3 Ordering information scheme Figure 16. Ordering information scheme SM Surface mount Peak pulse power 6 = 600 W Transil in SMB Breakdown voltage 30 = 30 V Types CA = Bidirectional A = Unidirectional Automotive grade 8/12 Doc ID 17741 Rev 3 6 T XX CA Y SM6TY 4 Packaging information Packaging information Case: JEDEC DO-214AA molded plastic over planar junction Terminals: solder plated, solderable as per MIL-STD-750, Method 2026 Polarity: for unidirectional types the band indicates cathode Flammability: epoxy meets UL 94, V0 RoHS package In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Table 3. SMB dimensions Dimensions E1 Ref. D Millimeters Inches Min. Max. Min. Max. A1 1.90 2.45 0.075 0.096 A2 0.05 0.20 0.002 0.008 b 1.95 2.20 0.077 0.087 c 0.15 0.40 0.006 0.016 D 3.30 3.95 0.130 0.156 E 5.10 5.60 0.201 0.220 E1 4.05 4.60 0.159 0.181 L 0.75 1.50 0.030 0.059 E A1 A2 C L b Figure 17. SMB footprint dimensions in mm (inches) 1.62 2.60 (0.064) (0.102) Figure 18. Marking layout(1) 1.62 (0.064) Cathode bar (unidirectional devices only ) 2.18 (0.086) 5.84 (0.300) x x x z y ww ECOPACK compliance XXX: Marking Z: Manufacturing location Y: Year WW: Week 1. Marking layout can vary according to assembly location. Doc ID 17741 Rev 3 9/12 Ordering information Table 4. 5 SM6TY Marking Order code Marking Order code Marking SM6T6V8AY DEY SM6T6V8CAY LEY SM6T7V5AY DGY SM6T7V5CAY LGY SM6T10AY DPY SM6T10CAY LPY SM6T12AY DTY SM6T12CAY LTY SM6T15AY DXY SM6T15CAY LXY SM6T18AY EEY SM6T18CAY MEY SM6T22AY EKY SM6T22CAY MKY SM6T24AY EMY SM6T24CAY MMY SM6T27AY EPY SM6T27CAY MPY SM6T30AY ERY SM6T30CAY MRY SM6T33AY ETY SM6T33CAY MTY SM6T36AY EVY SM6T36CAY MVY SM6T39AY EXY SM6T39CAY MXY SM6T42AY FBY SM6T42CAY NAY SM6T47AY FAY SM6T47CAY NBY SM6T56AY FLY SM6T56CAY NLY SM6T68AY FQY SM6T68CAY NQY SM6T75AY FSY SM6T75CAY NSY SM6T82AY FWY SM6T82CAY NWY Ordering information Table 5. Ordering information Order code Marking SM6TxxxAy/CAy(1) See Table 4 on page 10 Package Weight SMB 0.11 g Base qty Delivery mode 2500 Tape and reel 1. Where xxx is nominal value of VBR and A or CA indicates unidirectional or bidirectional version. See Table 2 for list of available devices and their order codes 10/12 Doc ID 17741 Rev 3 SM6TY 6 Revision history Revision history Table 6. Document revision history Date Revision Changes 15-Sep-2010 1 Initial release. 18-Oct-2011 2 Deleted old Table 2. Thermal parameter. Updated Table 2 and added order codes inTable 4. Updated Figure 5, 10 and 11. Updated Complies with the following standards on page 1. 27-Mar-2012 3 Added footnote on page 1. Doc ID 17741 Rev 3 11/12 SM6TY Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12 Doc ID 17741 Rev 3