SinglFuseTM SF-1206FP Series Features n Fast acting precision thin film chip fuse for overcurrent protection n 3216 (EIA 1206) miniature footprint n Surface mount packaging for automated assembly n UL listed (UL 248-14) n RoHS compliant* and halogen free** SF-1206FP Series - Fast Acting Precision Surface Mount Fuses Electrical Characteristics Model SF-1206FP050 SF-1206FP080 SF-1206FP100 SF-1206FP125 SF-1206FP150 SF-1206FP200 SF-1206FP250 SF-1206FP300 SF-1206FP400 SF-1206FP500 SF-1206FP700 Rated Current (Amps) 0.50 0.80 1.00 1.25 1.50 2.00 2.50 3.00 4.00 5.00 7.00 Fusing Time Open within 5 sec. at 200 % rated current Resistance (m) Typ.*** 527.5 211 145.5 90 83 57 37 26 18 13 9 Rated Voltage Breaking Capacity DC 63 V DC 63 V 50 A DC 32 V DC 32 V 50 A Typical I2t (A2s) **** 0.015 0.040 0.062 0.094 0.141 0.285 0.445 0.639 1.109 1.710 3.300 *** Resistance value measured with less than 10 % of rated current. Tolerance 25 %. ****Typical I2t value measured at 10x rated current. Reliability Testing No. Test Requirement Test Condition 1 Carrying Capacity No fusing 2 Fusing Time Within 5 seconds 200 % of its rated current 3 Interrupting Ability No mechanical damages After the fuse is interrupted, rated voltage applied for 30 seconds again 4 Bending Test No mechanical damages Distance between holding points: 90 mm, Bending: 3 mm,1 time, 30 seconds 5 Resistance to Solder Heat 20 % 260 C 5 C,10 seconds 1 second 6 Solderability 95 % coverage minimum 235 C 5 C, 2 0.5 second 245 C 5 C, 2 0.5 second (lead free) 7 Temperature Rise <75 C 100 % of its rated current, measure of surface temperature 8 Resistance to Dry Heat 20 % 105 C 5 C,1000 hours 9 Resistance to Solvent No evident damage on protective coating and marking 23 C 5 C of isopropyl alcohol, 90 seconds 10 Residual Resistance 10k ohms or more Measure DC resistance after fusing 11 Thermal Shock DR < 10 % -20 C / +25 C /+125 C /+25 C, 10 cycles Agency Recognition UL File Number................................................................ E198545 Rated current, 4 hours WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov Environmental Characteristics Operating Temperature........................................-20 C to +105 C Storage Conditions Temperature......................................................+5 C to +35 C Humidity................................................................40 % to 75 % Shelf Life................................ 2 years from manufacturing date Moisture Sensitivity Level..............................................................1 ESD Classification (HBM)...................................................Class 6 * RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. ** Bourns considers a product to be "halogen free" if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less. "SinglFuse" is a trademark of Bourns, Inc. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SinglFuseTM SF-1206FP Series Applications n Portable memory n Cell phones n LCD monitors n Rechargeable battery packs n Disk drives n Battery chargers n PDAs n Set top boxes n Digital cameras n Industrial controllers 250 n DVDs Peak: 250 +0/-5 C 230 C or higher TEMPERATURE (C) 200 SF-1206FP Series - Fast Acting Precision Surface Mount Fuses Solder Reflow Recommendations 150 180 C PRE-HEATING ZONE 150 C 90 30 Seconds 100 250 30 10 Seconds Peak: 250 +0/-5 C SOLDERING ZONE 230 C or higher TEMPERATURE (C) 50 200 150 HEATING TIME PRE-HEATING ZONE 180 C PEAK: 250 +0/-5 C, 5 seconds PRE-HEATING ZONE: 150 to 180 C, 90 30 seconds SOLDERING ZONE: 230 C or higher, 30 10 seconds 150 C 90 30 Seconds 100 30 10 Seconds 3.1 0.1 2.2 0.2 (.087 .008) (.122 .004) SOLDERING ZONE 50 HEATING TIME 1.65 0.15 (.065 .006) 1.55 0.1 (.061 .004) PEAK: 250 +0/-5 C, 5 seconds PRE-HEATING ZONE: 150 to 180 C, 90 30 seconds Product Dimensions SOLDERING ZONE: 230 C or higher, 30 10 seconds 0.5 0.3 (.020 .012) 3.1 0.1 (.122 .004) 3.1 0.1 (.122 .004) 1.55 0.1 (.061 .004) 0.5 0.2 (.020 .008) 0.5 0.3 (.020 .012) 0.5 0.3 (.020 .012) 4.7 0.3 (.185 .012) 2.2 0.2 (.087 .008) 1.65 0.15 (.065 .006) MM (.185 .012) (INCHES) 0.5 0.3 DIMENSIONS: (.020 .012) 0.6 0.1 (.024 .004) Thermal Derating Curve PERCENT OF RATING (%) 1.55 0.1 (.061 .004) 0.5 0.2 (.020 .008) Recommended Pad Layout 1.65 0.15 (.065 .006) 4.7 0.3 0.5 0.3 (.020 .012) 0.6 0.1 (.024 .004) 0.5 0.2 (.020 .008) 0.5 0.3 (.020 .012)2.2 0.2 (.087 .008) 0.6 0.1 (.024 .004) 4.7 0.3 (.185 .012) Packaging Quantity 5,000 pieces per 7-inch reel 120 0.5 0.2 (.020 .008) 0.5 0.2 (.020 .008) 110 0.5 0.2 (.020 .008) Construction & Material Content 100 OVERCOAT 90 80 -20 Sn PLATING 0 20 40 60 80 AMBIENT TEMPERATURE (C) 100 120 FUSE ELEMENT Cu / Ni PLATING CERAMIC SUBSTRATE Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SF-1206FP Series - Fast Acting Precision Surface Mount Fuses Average Time Current Curves 100 1.50 A 1.25 A 1.501.00 A A 1.250.80 A A 1.00 A 0.50 A 0.80 A 0.50 A Minimum I2T V Clear Time Curves 2.00 A 2.50 A 2.00 A 3.00 A 2.50 A 4.00 A 3.00 A 5.00 A 4.00 A 7.00 A 5.00 A 7.00 A 7.00 A 5.00 A 100 7.00 A 5.00 A4.00 A 100 4.00 A3.00 A 3.00 2.50 A A 2.00 A 2.50 A 2.00 A1.50 A 100 10 10 1.50 A1.25 A 10 1.25 1.00 A A JOULE INTEGRAL (A2 SEC) JOULE INTEGRAL (A2 SEC) CLEARING TIME (S) CLEARING TIME (S) 10 1 1.00 A0.80 A 0.80 A 0.50 A 1 0.50 A 1 1 0.1 0.1 0.1 0.1 0.01 0.01 0.01 0.001 0.1 0.001 0.1 1 1 10 CURRENT 10 (A) CURRENT (A) Typical Part Marking Represents total content. Layout may vary. 100 0.01 0.001 0.001 0.01 0.01 100 0.1 0.1 (S) CLEARING TIME 1 1 CLEARING TIME (S) How to Order SF - 1206 FP 050 - 2 SinglFuseTM Product Designator SMD Footprint 3216 (EIA 1206) size RATED CURRENT (A) T = 2.50 F = 0.50 3 = 3.00 K = 0.80 W = 4.00 L = 1.00 Y = 5.00 M = 1.25 Z = 7.00 P = 1.50 S = 2.00 Fuse Blow Type FP = Fast acting precision Rated Current 050-700 (500 mA - 7.00 A) Packaging Type - 2 = Tape & Reel (5,000 pcs./reel) REV. D 01/19 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SF-1206FP Series Tape and Reel Specifications SF-1206FP Series per EIA 481-2 Tape Dimensions W 8.0 0.2 (.315 .008) P0 4.0 0.1 (.157 .004) P1 4.0 0.1 (.157 .004) P2 2.0 0.05 (.079 .002) A 2.0 0.15 (.079 .006) B 3.6 0.2 (.142 .008) F 3.5 0.05 (.138 .002) E 1.75 0.1 (.069 .004) 1.5 + 0.1/-0 (.059 + .004/-0) D0 0.84 0.1 (.033 .004) T Reel Dimensions A 178 0.2 (7.087 .079) B Min. 60.0 1.0 (2.362 .039) C 13.0 1.0 (.512 .039) W 9.0 1.0 (.354 .039) T 11.4 2.0 (.449 .079) T DIMENSIONS: MM (INCHES) W BOTTOM TAPE A DIA. C DIA. DO PO E TOP TAPE B B DIA. PAPER TAPE RESISTOR TAPE T F A P1 W P2 DIRECTION OF UNREELING Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns(R) products manufactured by or on behalf of Bourns, Inc. and (32 ?+( 3$2".++$"3(5$+8:.41-2; Unless otherwise expressly indicated in writing, Bourns(R) products and data sheets relating thereto are subject to change 6(3'.43-.3("$2$122'.4+#"'$"*%.1 -#.!3 (-3'$+ 3$231$+$5 -3(-%.1, 3(.- -#5$1(%83' 324"'(-%.1, 3(.-(2"411$-3 and complete before placing orders for Bourns(R) products. The characteristics and parameters of a Bourns(R) product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on Bourns' knowledge of typical requirements in generic applications. The characteristics and parameters of a Bourns(R)/1.#4"3(- 42$1 //+(" 3(.-, 85 18 %1.,3'$# 3 2'$$3"' 1 "3$1(23("2 -#/ 1 ,$3$12#4$3.(3'$".,!(- 3(.-.%3'$.41-2(R) product with other components (-3'$42$1<2 //+(" 3(.-.1((3'$$-5(1.-,$-3.%3'$42$1 //+(" 3(.-(32$+%'$"' 1 "3$1(23("2 -#/ 1 ,$3$12.% .41-2(R) /1.#4"3 +2." - -##.5 18(-#(>$1$-3 //+(" 3(.-2 -# "34 +/$1%.1, -"$, 85 18.5$13(,$2$122'.4+# +6 825$1(%8 the actual performance of the Bourns(R)/1.#4"3(-3'$(12/$"(="#$5("$2 -# //+(" 3(.-2 -#, *$3'$(1.6-(-#$/$-#$-3 )4#&,$-321$& 1#(-&3'$ ,.4-3.% ##(3(.- +3$23, 1&(-3.#$2(&-(-3.3'$(1#$5("$.1 //+(" 3(.-3.".,/$-2 3$%.1 #(>$1$-"$2!$36$$-+ !.1 3.18 -#1$ +6.1+#".-#(3(.-2 -+$22.41-2' 2$7/+("(3+8#$2(&- 3$# -(-#(5(#4 +.41-2(R) product as meeting the requirements of a particular industry 23 -# 1#$& .1 / 13("4+ 104 +(=" 3(.-$&+(23$#.11$".&-(9$#.41-2(2-.31$2/.-2(!+$%.1 -8 % (+41$.% -(-#(5(#4 +.41-2(R)/1.#4"33.,$$33'$1$04(1$,$-32.%24"'(-#4231823 -# 1#.1/ 13("4+ 104 +(=" 3(.-2$12 of Bourns(R) products are responsible for ensuring compliance with safety-related requirements and standards applicable to 3'$(1#$5("$2.1 //+(" 3(.-2 Bourns(R)/1.#4"32 1$-.31$".,,$-#$# 43'.1(9$#.1(-3$-#$#%.142$(--4"+$ 1+(%$2 5(-&+(%$"1(3(" +.1+(%$2423 (-(-& //+(" 3(.-2-.1(- -8.3'$1 //+(" 3(.-26'$1$% (+41$.1, +%4-"3(.-, 81$24+3(-/$12.- +(-)418#$ 3'.12$5$1$/1./$138 .1$-5(1.-,$-3 +# , &$-+$22$7/1$22+8 -#2/$"(=" ++8 //1.5$#(-61(3(-&!836. 43'.1(9$#.41-21$/1$2$-3 3(5$2 on a case-by-case basis, use of any Bourns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ourns(R)23 -# 1#/1.#4"32 1$-.33$23$#3.".,/+86(3'-(3$#3 3$2$#$1 +5( 3(.-#,(-(231 3(.-23 -# 1#2&$-$1 ++8 .1 -8.3'$1&$-$1 ++8$04(5 +$-3&.5$1-,$-3 +.1& -(9 3(.-23 -# 1# //+(" !+$3./1.#4"32#$2(&-$#.1, -4% "341$#%.1 42$(- (1"1 %3.12/ "$ //+(" 3(.-2.41-2$7/1$22+8(#$-3(=$2.41-2(R) standard products that are suitable for use in aircraft .12/ "$ //+(" 3(.-2.-24"'/1.#4"32<# 3 2'$$32(-3'$2$"3(.-$-3(3+$#://+(" 3(.-2;-+$22$7/1$22+8 -#2/$"(=" ++8 //1.5$#(-61(3(-&!836. 43'.1(9$#.41-21$/1$2$-3 3(5$2.- " 2$!8" 2$! 2(242$.% -8.3'$1.41-2(R) standard /1.#4"3(- - (1"1 %3.12/ "$ //+(" 3(.-,(&'3-.3!$2 %$ -#3'42(2-.31$".,,$-#$# 43'.1(9$#.1(-3$-#$# -#(2 3 the user's sole risk. '$42$ -#+$5$+.%3$23(-& //+(" !+$3..41-2(R) custom products shall be negotiated on a case-by-case basis by Bourns and the user for which such Bourns(R)"423.,/1.#4"32 1$2/$"( ++8#$2(&-$#!2$-3 61(33$- &1$$,$-3!$36$$-.41-2 -#3'$42$11$& 1#(-&3'$42$ -#+$5$+.%24"'3$23(-&3'$ !.5$/1.5(2(.-2 //+(" !+$3..41-2(R) standard products shall also apply to such Bourns(R) custom products. Users shall not sell, transfer, export or re-export any Bourns(R)/1.#4"32.13$"'-.+.&8%.142$(- "3(5(3($26'("'(-5.+5$3'$ #$2(&-#$5$+./,$-3/1.#4"3(.-42$.123."*/(+(-&.%-4"+$ 1"'$,(" +.1!(.+.&(" +6$ /.-2.1,(22(+$2-.12' ++3'$842$ Bourns(R)/1.#4"32.13$"'-.+.&8(- -8% "(+(386'("'$-& &$2(- "3(5(3($21$+ 3(-&3.24"'#$5("$2'$%.1$&.(-&1$231("3(.-2 //+83. ++42$2 -# //+(" 3(.-23' 35(.+ 3$- 3(.- +.1(-3$1- 3(.- +/1.'(!(3(.-2(-"+4#(-&$,! 1&.2.1(-3$1- 3(.- + 1$&4+ 3(.-2413'$1.41-2(R) products and Bourns technology and technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes. Bourns(R) products may not, without /1(.1 43'.1(9 3(.-%1.,.41-2 -#.13'$.5$1-,$-3!$1$2.+#31 -2%$11$#.11$$7/.13$#3. -8/ 138-.3$+(&(!+$ 3.1$"$(5$".,,.#(3($22.%36 1$ -#3$"'-(" +# 3 .3'$, 7(,4,$73$-3/$1,(33$#!8 //+(" !+$+ 6.41-2#(2"+ (,2( -8 -# +++( !(+(38%.12/$"( +/4-(3(5$".-2$04$-3( + (-"(#$-3 +.1(-#(1$"3# , &$2.1+.231$5$-4$2.1+.23/1.=32 -#(( -8 -# ++(,/+($#6 11 -3($2(-"+4#(-&(,/+($#6 11 -3($2 .%=3-$22%.1/ 13("4+ 1/41/.2$-.-(-%1(-&$,$-3 -#,$1"' -3 !(+(38 bilingual versions are available at: Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf