TLE7250XLE - INFINEON TECHNOLOGIES AG

Automotive Power

Data Sheet

Rev. 1.0, 2015-08-12

TLE7250X

High Speed CAN-Transceiver

TLE7250XLE

TLE7250XSJ

Data Sheet 2 Rev. 1.0, 2015-08-12
 
TLE7250XLE
TLE7250XSJ
Table of Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Pin Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
2 Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
1 High Speed CAN Physical Layer   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
2 Modes of Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
2.1 Normal-operating Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
2.2 Receive-only Mode   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
3 Power-up and Undervoltage Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
3.1 Power-down State  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
3.2 Forced Power-save Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
3.3 Power-up  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
3.4 Undervoltage on the Digital Supply VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
3.5 Undervoltage on the Transmitter Supply VCC  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
3.6 Voltage Adaption to the Microcontroller Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
Fail Safe Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
1 Short Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
2 Unconnected Logic Pins  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
3 TxD Time-out Function  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
4 Overtemperature Protection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
5 Delay Time for Mode Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17
1 Absolute Maximum Ratings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17
2 Functional Range  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
3 Thermal Resistance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19
1 Functional Device Characteristics   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19
2 Diagrams   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
Application Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
1 ESD Robustness according to IEC61000-4-2   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2 Application Example  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
3 Examples for Mode Changes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28
3.1 Mode Change while the TxD Signal is “low”   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
3.2 Mode Change while the Bus Signal is “dominant”  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
4 Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
Package Outline  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Revision History  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table of Contents

Type Package Marking

TLE7250XLE PG-TSON-8 7250X

TLE7250XSJ PG-DSO-8 7250X

PG-TSON-8

PG-DSO-8

Data Sheet 3 Rev. 1.0, 2015-08-12

High Speed CAN-Transceiver TLE7250XLE

TLE7250XSJ

1Overview

Features

• Fully compatible to ISO 11898-2

• Wide common mode range for electromagnetic immunity (EMI)

• Very low electromagnetic emission (EME)

• Excellent ESD robustness

• Guaranteed loop delay symmetry to support CAN FD data frames up

to 2 MBit/s

•VIO input for voltage adaption to the microcontroller supply

• Extended supply range on VCC and VIO supply

• CAN short circuit proof to ground, battery and VCC

• TxD time-out function

• Low CAN bus leakage current in power-down state

• Overtemperature protection

• Protected against automotive transients

• Receive-only mode

• Green Product (RoHS compliant)

• Two package variants: PG-DSO-8 and PG-TSON-8

• AEC Qualified

Description

The TLE7250X is a transceiver designed for HS CAN networks in automotive and industrial applications. As an

interface between the physical bus layer and the CAN protocol controller, the TLE7250X drives the signals to the

bus and protects the microcontroller against interferences generated within the network. Based on the high

symmetry of the CANH and CANL signals, the TLE7250X provides a very low level of electromagnetic emission

(EME) within a wide frequency range.

The TLE7250X is available in a small, leadless PG-TSON-8 package and in a PG-DSO-8 package. Both packages

are RoHS compliant and halogen free. Additionally the PG-TSON-8 package supports the solder joint

requirements for automated optical inspection (AOI). The TLE7250XLE and the TLE7250XSJ are fulfilling or

exceeding the requirements of the ISO11898-2.

The TLE7250X provides a digital supply input VIO and a receive-only mode. It is designed to fulfill the enhanced

physical layer requirements for CAN FD and supports data rates up to 2 MBit/s.

On the basis of a very low leakage current on the HS CAN bus interface the TLE7250X provides an excellent

passive behavior in power-down state. These and other features make the TLE7250X exceptionally suitable for

mixed supply HS CAN networks.

TLE7250XLE

TLE7250XSJ

Overview

Data Sheet 4 Rev. 1.0, 2015-08-12

Based on the Infineon Smart Power Technology SPT, the TLE7250X provides excellent ESD immunity together

with a very high electromagnetic immunity (EMI). The TLE7250X and the Infineon SPT technology are AEC

qualified and tailored to withstand the harsh conditions of the automotive environment.

Two different operating modes, additional fail-safe features like a TxD time-out and the optimized output slew rates

on the CANH and CANL signals, make the TLE7250X the ideal choice for large HS CAN networks with high data

transmission rates.

TLE7250XLE

TLE7250XSJ

Block Diagram

Data Sheet 5 Rev. 1.0, 2015-08-12

2 Block Diagram

Figure 1 Functional block diagram

Driver

Temp-

protection Mode

control

CANH

CANL

GND

TxD

3VCC

VIO

RxD

Timeout

Transmitter

Receiver

VCC/2

Normal-mode receiver

Bus-biasing

TLE7250XLE

TLE7250XSJ

Pin Configuration

Data Sheet 6 Rev. 1.0, 2015-08-12

3 Pin Configuration

3.1 Pin Assignment

Figure 2 Pin configuration

3.2 Pin Definitions

Table 1 Pin definitions and functions

Pin No. Symbol Function

1TxDTransmit Data Input;

internal pull-up to VIO, “low” for “dominant” state.

2GNDGround

3VCC Transmitter Supply Voltage;

100 nF decoupling capacitor to GND required.

4RxDReceive Data Output;

“low” in “dominant” state.

5VIO Digital Supply Voltage;

supply voltage input to adapt the logical input and output voltage levels of the

transceiver to the microcontroller supply,

100 nF decoupling capacitor to GND required.

6CANLCAN Bus Low Level I/O;

“low” in “dominant” state.

7CANHCAN Bus High Level I/O;

“high” in “dominant” state.

TxD RM

VIO

GND

VCC

RxD

CANH

CANL

TxD

GND

VCC

RxD

VIO

CANH

CANL

(Top-side x-ray view)

PAD

TLE7250XLE

TLE7250XSJ

Pin Configuration

Data Sheet 7 Rev. 1.0, 2015-08-12

8RMReceive-only Mode Input;

internal pull-down to GND, “low” for normal-operating mode.

PAD – Connect to PCB heat sink area.

Do not connect to other potential than GND.

Table 1 Pin definitions and functions (cont’d)

Pin No. Symbol Function

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 8 Rev. 1.0, 2015-08-12

4 Functional Description

HS CAN is a serial bus system that connects microcontrollers, sensors and actuators for real-time control

applications. The use of the Controller Area Network (abbreviated CAN) within road vehicles is described by the

international standard ISO 11898. According to the 7-layer OSI reference model the physical layer of a HS CAN

bus system specifies the data transmission from one CAN node to all other available CAN nodes within the

network. The physical layer specification of a CAN bus system includes all electrical and mechanical specifications

of a CAN network. The CAN transceiver is part of the physical layer specification. Several different physical layer

standards of CAN networks have been developed in recent years. The TLE7250X is a High Speed CAN

transceiver without a wake-up function and defined by the international standard ISO 11898-2.

4.1 High Speed CAN Physical Layer

Figure 3 High speed CAN bus signals and logic signals

TxD

CANH

CANL

Diff

RxD

= Digital supply voltage

= Transmitter supply voltage

TxD = Transmit data input from

the microcontroller

RxD = Receive data output to

the microcontroller

CANH = Bus level on the CANH

input/output

CANL = Bus level on the CANL

input/output

Diff

= Differential voltage

between CANH and CANL

Diff

= V

CANH

– V

CANL

“dominant” receiver threshold

“recessive” receiver threshold

Loop(H,L)

Loop(L,H)

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 9 Rev. 1.0, 2015-08-12

The TLE7250X is a High-Speed CAN transceiver, operating as an interface between the CAN controller and the

physical bus medium. A HS CAN network is a two wire, differential network which allows data transmission rates

for CAN FD frames up to 2 MBit/s. Characteristic for HS CAN networks are the two signal states on the HS CAN

bus: “dominant” and “recessive” (see Figure 3).

VCC, VIO and GND are the supply pins for the TLE7250X. The pins CANH and CANL are the interface to the

HS CAN bus and operate in both directions, as an input and as an output. RxD and TxD pins are the interface to

the CAN controller, the TxD pin is an input pin and the RxD pin is an output pin. The RM pin is the input pin for the

mode selection (see Figure 4).

By setting the TxD input pin to logical “low” the transmitter of the TLE7250X drives a “dominant” signal to the CANH

and CANL pins. Setting TxD input to logical “high” turns off the transmitter and the output voltage on CANH and

CANL discharges towards the “recessive” level. The “recessive” output voltage is provided by the bus biasing (see

Figure 1). The output of the transmitter is considered to be “dominant”, when the voltage difference between

CANH and CANL is at least higher than 1.5 V (VDiff =VCANH -VCANL).

Parallel to the transmitter the normal-mode receiver monitors the signal on the CANH and CANL pins and indicates

it on the RxD output pin. A “dominant” signal on the CANH and CANL pins sets the RxD output pin to logical “low”,

vice versa a “recessive” signal sets the RxD output to logical “high”. The normal-mode receiver considers a voltage

difference (VDiff) between CANH and CANL above 0.9 V as “dominant” and below 0.5 V as “recessive”.

To be conform with HS CAN features, like the bit to bit arbitration, the signal on the RxD output has to follow the

signal on the TxD input within a defined loop delay tLoop ≤255 ns.

The thresholds of the digital inputs (TxD and RM) and also the RxD output voltage are adapted to the digital power

supply VIO.

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 10 Rev. 1.0, 2015-08-12

4.2 Modes of Operation

The TLE7250X supports two different modes of operation, receive-only mode and normal-operating mode while

the transceiver is supplied according to the specified functional range. The mode of operation is selected by the

RM input pin (see Figure 4).

Figure 4 Mode state diagram

4.2.1 Normal-operating Mode

In normal-operating mode the transmitter and the receiver of the HS CAN transceiver TLE7250X are active (see

Figure 1). The HS CAN transceiver sends the serial data stream on the TxD input pin to the CAN bus. The data

on the CAN bus is displayed at the RxD pin simultaneously. A logical “low” signal on the RM pin selects the normal-

operating mode, while the transceiver is supplied by VCC and VIO (see Table 2 for details).

4.2.2 Receive-only Mode

In receive-only mode the normal-mode receiver is active and the transmitter is turned off. The TLE7250X can

receive data from the HS CAN bus, but cannot send any data to the HS CAN bus.

A logical “high” signal on the RM pin selects the receive-only mode, while the transceiver is supplied by VCC and

VIO (see Table 2 for details).

VCC > VCC(UV,R)

RM = 0

normal-operating

mode

RM = 1

receive-only mode

RM = 0 RM = 1

VIO > VIO(UV,R)

VCC > VCC(UV)

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 11 Rev. 1.0, 2015-08-12

4.3 Power-up and Undervoltage Condition

By detecting an undervoltage event, either on the transmitter supply VCC or the digital supply VIO, the transceiver

TLE7250X changes the mode of operation. Turning off the digital power supply VIO, the transceiver powers down

and remains in the power-down state. While switching off the transmitter supply VCC, the transceiver changes to

the forced power-save mode, (details see Figure 5).

Figure 5 Power-up and undervoltage

Table 2 Modes of operation

Mode RM VIO VCC Bus Bias Transmitter Normal-mode

Receiver

Low-power

Receiver

Normal-operating “low” “on” “on” VCC/2 “on” “on” not available

Receive-only “high” “on” “on” VCC/2 “off” “on” not available

Forced power-save “X” “on” “off” floating “off” “off” not available

Power-down state “X” “off” “X” floating “off” “off” not available

RM VCC VIO

power-down

state

“X”“X” “off”

normal-operating

mode

RM VCC VIO

0“on” “on”

forced power-save

mode

RM VCC VIO

“X” “off” “on”

receive-only

mode

RM VCC VIO

1 “on” “on”

VIO “on”

VCC “off”

RM “0”

VIO “on”

VCC “on”

RM “0”

VIO “on”

VCC “on”

RM “1”

VIO “on”

VCC “off”

RM “X”

VIO “on”

VCC “on”

RM “1”

VIO “on”

VCC “on”

RM “0”

VIO “on”

VCC “on”

RM “0”

VIO “on”

VCC “on”

RM “1”

VIO “on”

VCC “off”

RM “1”

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 12 Rev. 1.0, 2015-08-12

4.3.1 Power-down State

Independent of the transmitter supply VCC and of the RM input pin, the TLE7250X is in power-down state when

the digital supply voltage VIO is turned off (see Figure 5).

In the power-down state the input resistors of the receiver are disconnected from the bus biasing VCC/2. The CANH

and CANL bus interface of the TLE7250X is floating and acts as a high-impedance input with a very small leakage

current. The high-ohmic input does not influence the “recessive” level of the CAN network and allows an optimized

EME performance of the entire HS CAN network (see also Table 2).

4.3.2 Forced Power-save Mode

The forced power-save mode is a fail-safe mode to avoid any disturbance on the HS CAN bus, while the

TLE7250X faces a loss of the transmitter supply VCC.

In forced power-save mode, the transmitter and the normal-mode receiver are turned off and therefore the

transceiver TLE7250X can not disturb the bus media.

The RxD output pin is permanently set to logical “high”. The bus biasing is floating (details see Table 2).

The forced power-save mode can only be entered when the transmitter supply VCC is not available, either by

powering up the digital supply VIO only or by turning off the transmitter supply in normal-operating mode or in

receive-only mode (see Figure 5). While the transceiver TLE7250X is in forced power-save mode the RM pin is

disabled.

4.3.3 Power-up

The HS CAN transceiver TLE7250X powers up if at least the digital supply VIO is connected to the device. By

default the device powers up in normal-operating mode, due to the internal pull-down resistor on the RM pin to

GND.

In case the device needs to power-up in receive-only mode, the RM pin needs to be pulled active to logical “high”

and the supplies VIO and VCC have to be connected.

By supplying only the digital power supply VIO the TLE7250X powers up in forced power-save mode (see

Figure 5).

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 13 Rev. 1.0, 2015-08-12

4.3.4 Undervoltage on the Digital Supply VIO

If the voltage on VIO supply input falls below the threshold VIO <VIO(U,F), the transceiver TLE7250X powers down

and changes to the power-down state.

The undervoltage detection on the digital supply VIO has the highest priority and is independent of the transmitter

supply VCC and also independent of the currently selected operating mode, an undervoltage event on VIO always

powers down the TLE7250X.

Figure 6 Undervoltage on the digital supply VIO

“X” = don’t care

“low” due the internal

pull-down resistor1)

1)assuming no external signal applied

tDelay(UV) delay time undervoltage

VIO

hysteresis

VIO(UV,H)

VIO undervoltage monitor

VIO(UV,F)

VIO undervoltage monitor

VIO(UV,R)

transmitter supply voltage VCC = “don’t care”

power-down stateany mode of operation normal-operating mode

TLE7250XLE

TLE7250XSJ

Functional Description

Data Sheet 14 Rev. 1.0, 2015-08-12

4.3.5 Undervoltage on the Transmitter Supply VCC

In case the transmitter supply VCC falls below the threshold VCC <VCC(UV,F), the transceiver TLE7250X changes

the mode of operation to forced power-save mode. The transmitter and also the normal-mode receiver of the

TLE7250X are powered by the VCC supply. In case of an insufficient VCC supply, the TLE7250X can neither

transmit the CANH and CANL signals correctly to the bus, nor can it receive them properly. Therefore the

TLE7250X blocks the transmitter and the receiver in forced power-save mode (see Figure 7).

The undervoltage detection on the transmitter supply VCC is active in normal-operating mode and in receive-only

mode (see Figure 5).

Figure 7 Undervoltage on the transmitter supply VCC

4.3.6 Voltage Adaption to the Microcontroller Supply

The HS CAN transceiver TLE7250X has two different power supplies, VCC and VIO. The power supply VCC supplies

the transmitter and the normal-mode receiver. The power supply VIO supplies the digital input and output buffers

and it is also the main power domain for the internal logic.

To adjust the digital input and output levels of the TLE7250X to the I/O levels of the external microcontroller,

connect the power supply VIO to the microcontroller I/O supply voltage (see Figure 13).

Note: In case the digital supply voltage VIO is not required in the application, connect the digital supply voltage VIO

to the transmitter supply VCC.

forced power-save modeany mode of operation normal-operating mode

“X” = don’t care

“low” due the internal

pull-down resistor1)

1)assuming no external signal applied

digital supply voltage VIO = “on”

tDelay(UV) delay time undervoltage

VCC

hysteresis

VCC(UV,H)

VCC undervoltage monitor

VCC(UV,F)

VCC undervoltage monitor

VCC(UV,R)

TLE7250XLE

TLE7250XSJ

Fail Safe Functions

Data Sheet 15 Rev. 1.0, 2015-08-12

5 Fail Safe Functions

5.1 Short Circuit Protection

The CANH and CANL bus outputs are short circuit proof, either against GND or a positive supply voltage. A current

limiting circuit protects the transceiver against damages. If the device is heating up due to a continuous short on

the CANH or CANL, the internal overtemperature protection switches off the bus transmitter.

5.2 Unconnected Logic Pins

All logic input pins have an internal pull-up resistor to VIO or a pull-down resistor to GND. In case the VIO supply is

activated and the logical pins are open, the TLE7250X enters into the normal-operating mode by default. The TxD

input is pulled to logical “high” due to the internal pull-up resistor to VIO. The HS CAN transceiver TLE7250X will

not influence the data on the CAN bus as long the TxD input pin remains logical “high”.

5.3 TxD Time-out Function

The TxD time-out feature protects the CAN bus against permanent blocking in case the logical signal on the TxD

pin is continuously “low”. A continuous “low” signal on the TxD pin might have its root cause in a locked-up

microcontroller or in a short circuit on the printed circuit board, for example. In normal-operating mode, a logical

“low” signal on the TxD pin for the time t > tTxD enables the TxD time-out feature and the TLE7250X disables the

transmitter (see Figure 8). The receiver is still active and the data on the bus continues to be monitored by the

RxD output pin.

Figure 8 TxD time-out function

Figure 8 illustrates how the transmitter is deactivated and activated again. A permanent “low” signal on the TxD

input pin activates the TxD time-out function and deactivates the transmitter. To release the transmitter after a TxD

time-out event the TLE7250X requires a signal change on the TxD input pin from logical “low” to logical “high”.

TxD

CANH

CANL

RxD

TxD time-out TxD time–out released

t > tTxD

TLE7250XLE

TLE7250XSJ

Fail Safe Functions

Data Sheet 16 Rev. 1.0, 2015-08-12

5.4 Overtemperature Protection

The TLE7250X has an integrated overtemperature detection to protect the TLE7250X against thermal overstress

of the transmitter. The overtemperature protection is active in normal-operating mode and disabled in receive-only

mode. In case of an overtemperature condition, the temperature sensor will disable the transmitter (see Figure 1)

while the transceiver remains in normal-operating mode.

After the device has cooled down the transmitter is activated again (see Figure 9). A hysteresis is implemented

within the temperature sensor.

Figure 9 Overtemperature protection

5.5 Delay Time for Mode Change

The HS CAN transceiver TLE7250X changes the mode of operation within the time window tMode. During the mode

change the normal-mode receiver and the RxD output are active and reflect the on the HS CAN input pins (see

as an example Figure 14 and Figure 15).

TxD

CANH

CANL

RxD

TJSD (shut down temperature)

switch-on transmitter

˂T

cool down

TLE7250XLE
TLE7250XSJ
General Product Characteristics
 
Data Sheet 17 Rev. 1.0, 2015-08-12
 
6 General Product Characteristics
6.1 Absolute Maximum Ratings
Note:  Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute 
maximum rating conditions for extended periods may affect device reliability. Integrated protection functions 
are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions 
are considered as “outside” normal-operating range. Protection functions are not designed for continuos 
repetitive operation.
Table 3 Absolute maximum ratings voltages, currents and temperatures1)
All voltages with respect to ground; positive current flowing into pin;
(unless otherwise specified)
1) Not subject to production test, specified by design
Parameter Symbol Values Unit Note / Test Condition Number
Min. Typ. Max.
Voltages
Transmitter supply voltage VCC -0.3 – 6.0 V – P_6.1.1
Digital supply voltage VIO -0.3 – 6.0 V – P_6.1.2
CANH DC voltage versus GND VCANH -40 – 40 V – P_6.1.3
CANL DC voltage versus GND VCANL -40 – 40 V – P_6.1.4
Differential voltage between 
CANH and CANL
VCAN_Diff -40 – 40 V – P_6.1.5
Voltages at the input pins:
RM, TxD
VMAX_IN -0.3 – 6.0 V – P_6.1.6
Voltages at the output pin:
RxD
VMAX_OUT -0.3 – VIO V – P_6.1.7
Currents
RxD output current IRxD -20 – 20 mA – P_6.1.8
Temperatures
Junction temperature Tj-40 – 150 °C – P_6.1.9
Storage temperature TS-55 – 150 °C – P_6.1.10
ESD Resistivity
ESD immunity at CANH, CANL 
versus GND
VESD_HBM_
CAN
-9 – 9 kV HBM
(100 pF via 1.5 kΩ)2)
2) ESD susceptibility, Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001
P_6.1.11
ESD immunity at all other pins VESD_HBM_
ALL
-2 – 2 kV HBM
(100 pF via 1.5 kΩ)2)
P_6.1.12
ESD immunity to GND VESD_CDM -750 – 750 V CDM3)
3) ESD susceptibility, Charge Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1
P_6.1.13

TLE7250XLE
TLE7250XSJ
General Product Characteristics
 
Data Sheet 18 Rev. 1.0, 2015-08-12
 
6.2 Functional Range
Note: Within the functional range the IC operates as described in the circuit description. The electrical 
characteristics are specified within the conditions given in the related electrical characteristics table. 
6.3 Thermal Resistance
Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, 
please visit www.jedec.org. 
Table 4 Functional range
Parameter Symbol Values Unit Note / 
Test Condition
Number
Min. Typ. Max.
Supply Voltages
Transmitter supply voltage VCC 4.5 – 5.5 V – P_6.2.1
Digital supply voltage VIO 3.0 – 5.5 V – P_6.2.2
Thermal Parameters
Junction temperature Tj-40 – 150 °C 1)
1) Not subject to production test, specified by design.
P_6.2.3
Table 5 Thermal resistance1)
1) Not subject to production test, specified by design
Parameter Symbol Values Unit Note / 
Test Condition
Number
Min. Typ. Max.
Thermal Resistances
Junction to Ambient PG-TSON-8 RthJA –55–K/W
2) TLE7250XLE
2) Specified RthJA value is according to Jedec JESD51-2,-7 at natural convection on FR4 2s2p board. The product 
(TLE7250X) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu).
P_6.3.1
Junction to Ambient PG-DSO-8 RthJA –130–K/W
2) TLE7250XSJ P_6.3.4
Thermal Shutdown (junction temperature)
Thermal shutdown temperature TJSD 150 175 200 °C – P_6.3.2
Thermal shutdown hysteresis ∆T– 10 – K – P_6.3.3

TLE7250XLE
TLE7250XSJ
Electrical Characteristics
 
Data Sheet 19 Rev. 1.0, 2015-08-12
 
7 Electrical Characteristics
7.1 Functional Device Characteristics
Table 6 Electrical characteristics
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL=60Ω; -40 °C < Tj< 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter Symbol Values Unit Note / Test Condition Number
Min. Typ. Max.
Current Consumption
Current consumption at VCC 
normal-operating mode
ICC – 2.6 4 mA “recessive” state, 
VTxD = VIO, VRM =0V; 
P_7.1.1
Current consumption at VCC 
normal-operating mode
ICC – 38 60 mA “dominant” state,
 VTxD =VRM =0V; 
P_7.1.2
Current consumption at VIO 
normal-operating mode
IIO ––1mAVRM = 0 V; P_7.1.3
Current consumption at VCC
receive-only mode
ICC(ROM) ––2mAVRM =VTxD = VIO; P_7.1.4
Current consumption at VIO 
receive-only mode
IIO(ROM) ––1mAVRM =VIO; P_7.1.5
Supply Resets
VCC undervoltage monitor
rising edge
VCC(UV,R) 3.8 4.0 4.3 V – P_7.1.6
VCC undervoltage monitor
falling edge
VCC(UV,F) 3.65 3.85 4.3 V – P_7.1.26
VCC undervoltage monitor
hysteresis
VCC(UV,H) –150–mV
1) P_7.1.7
VIO undervoltage monitor
rising edge
VIO(UV,R) 2.0 2.5 3.0 V – P_7.1.8
VIO undervoltage monitor
falling edge
VIO(UV,F) 1.8 2.3 3.0 V – P_7.1.27
VIO undervoltage monitor
hysteresis
VIO(UV,H) –200–mV
1) P_7.1.9
VCC and VIO undervoltage delay 
time
tDelay(UV) ––100µs
1) (see Figure 6 and 
Figure 7);
P_7.1.10
Receiver Output RxD
“High” level output current IRD,H – -4-2mAVRxD =VIO -0.4V, 
VDiff <0.5V; 
P_7.1.11
“Low” level output current IRD,L 24–mAVRxD =0.4V, V Diff > 0.9 V;   P_7.1.12

TLE7250XLE
TLE7250XSJ
Electrical Characteristics
 
Data Sheet 20 Rev. 1.0, 2015-08-12
 
Transmission Input TxD
“High” level input voltage 
threshold
VTxD,H –0.5 
× VIO
0.7 
× VIO
V “recessive” state; P_7.1.13
“Low” level input voltage 
threshold
VTxD,L 0.3 
× VIO
0.4 
× VIO
– V “dominant” state; P_7.1.14
Pull-up resistance RTxD 10 25 50 kΩ– P_7.1.15
Input hysteresis VHYS(TxD) –450–mV
1) P_7.1.16
Input capacitance CTxD ––10pF
1) P_7.1.17
TxD permanent “dominant” 
timeout
tTxD 4.5 – 16 ms normal-operating mode;  P_7.1.18
Receive-only Input RM
“High” level input voltage 
threshold
VRM,H –0.5 
× VIO
0.7 
× VIO
V receive-only mode;  P_7.1.19
“Low” level input voltage 
threshold
VRM,L 0.3 
× VIO
0.4 
× VIO
– V normal-operating mode;  P_7.1.20
Pull-down resistance RRM 10 25 50 kΩ– P_7.1.21
Input capacitance CRM ––10pF
1) P_7.1.22
Input hysteresis VHYS(RM) –200–mV
1) P_7.1.23
Bus Receiver
Differential receiver threshold 
“dominant”
normal-operating mode and 
receive-only mode
VDiff_D –0.750.9V
2) P_7.1.24
Differential receiver threshold 
“recessive” 
normal-operating mode and 
receive-only mode
VDiff_R 0.5 0.66 – V 2) P_7.1.25
Common mode range CMR -12 – 12 V VCC = 5 V; P_7.1.28
Differential receiver hysteresis
normal-operating mode
VDiff,hys –90–mV 
1) P_7.1.29
CANH, CANL input resistance Ri10 20 30 kΩ“recessive” state;  P_7.1.30
Differential input resistance RDiff 20 40 60 kΩ“recessive” state;  P_7.1.31
Input resistance deviation 
between CANH and CANL
∆Ri- 1  –1%
1) “recessive” state;  P_7.1.32
Input capacitance CANH, CANL 
versus GND
CIn – 2040pF
1) VTxD =VIO; P_7.1.33
Differential input capacitance CIn_Diff – 1020pF
1) VTxD =VIO; P_7.1.34
Table 6 Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL=60Ω; -40 °C < Tj< 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter Symbol Values Unit Note / Test Condition Number
Min. Typ. Max.

TLE7250XLE
TLE7250XSJ
Electrical Characteristics
 
Data Sheet 21 Rev. 1.0, 2015-08-12
 
Bus Transmitter
CANL/CANH “recessive”
output voltage
normal-operating mode
VCANL/H 2.0 2.5 3.0 V VTxD =VIO, 
no load; 
P_7.1.35
CANH, CANL “recessive” 
output voltage difference
normal-operating mode
VDiff_NM -500 – 50 mV VTxD =VIO, 
no load; 
P_7.1.36
CANL “dominant” 
output voltage
normal-operating mode
VCANL 0.5 – 2.25 V VTxD = 0 V; P_7.1.38
CANH “dominant” 
output voltage
normal-operating mode
VCANH 2.75 – 4.5 V VTxD = 0 V; P_7.1.39
CANH, CANL “dominant” 
output voltage difference
normal-operating mode 
according to ISO 11898-2
VDiff =VCANH -VCANL
VDiff 1.5 – 3.0 V VTxD =0V, 
50 Ω<RL<65Ω,
4.75 < VCC <5.25V;
P_7.1.40
CANH, CANL “dominant” 
output voltage difference
normal-operating mode
VDiff =VCANH -VCANL
VDiff_R45 1.4 – 3.0 V VTxD =0V, 
45 Ω<RL<50Ω,
4.75 < VCC <5.25V;
P_7.1.37
Driver “dominant” symmetry 
normal-operating mode
VSYM =V
CANH +VCANL
VSYM 4.5 5 5.5 V VCC =5.0V, VTxD = 0 V; P_7.1.41
CANL short circuit current ICANLsc 40 75 100 mA VCANLshort =18V, 
VCC =5.0V, t<tTxD,
 VTxD =0V; 
P_7.1.42
CANH short circuit current ICANHsc -100 -75 -40 mA VCANHshort =0V, 
VCC =5.0V, t<tTxD,
 VTxD =0V; 
P_7.1.43
Leakage current, CANH ICANH,lk -5–5µAVCC =V
IO =0V,
0V<VCANH <5V,
VCANH =VCANL;
P_7.1.44
Leakage current, CANL ICANL,lk -5–5µAVCC =V
IO =0V,
0V<VCANL <5V, 
VCANH =VCANL;
P_7.1.45
Table 6 Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL=60Ω; -40 °C < Tj< 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter Symbol Values Unit Note / Test Condition Number
Min. Typ. Max.

TLE7250XLE
TLE7250XSJ
Electrical Characteristics
 
Data Sheet 22 Rev. 1.0, 2015-08-12
 
Dynamic CAN-Transceiver Characteristics
Propagation delay
TxD-to-RxD “low”
(“recessive to “dominant”)
tLoop(H,L) –180255nsCL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.46
Propagation delay
TxD-to-RxD “high”
(“dominant” to “recessive”)
tLoop(L,H) –180255nsCL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.47
Propagation delay 
extended load
TxD-to-RxD “low”
(“recessive to “dominant”)
tLoop_Ext(H
,L)
– – 300 ns 1) CL= 200 pF, 
RL=120Ω, 
4.75 V < VCC <5.25V,
CRxD =15pF; 
P_7.1.52
Propagation delay
extended load
TxD-to-RxD “high”
(“dominant” to “recessive”)
tLoop_Ext(L
,H)
– – 300 ns 1) CL= 200 pF, 
RL=120Ω, 
4.75 V < VCC <5.25V,
CRxD =15pF; 
P_7.1.54
Propagation delay
TxD “low” to bus “dominant”
td(L),T – 90 140 ns CL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.48
Propagation delay
TxD “high” to bus “recessive”
td(H),T – 90 140 ns CL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.49
Propagation delay
bus “dominant” to RxD “low”
td(L),R – 90 140 ns CL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.50
Propagation delay
bus “recessive” to RxD “high”
td(H),R – 90 140 ns CL= 100 pF, 
4.75 V < VCC < 5.25 V, 
CRxD =15pF; 
P_7.1.51
Delay Times 
Delay time for mode change tMode ––20µs
1) (see Figure 14 and 
Figure 15); 
P_7.1.53
Table 6 Electrical characteristics (cont’d)
4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL=60Ω; -40 °C < Tj< 150 °C; all voltages with respect to ground;
positive current flowing into pin; unless otherwise specified.
Parameter Symbol Values Unit Note / Test Condition Number
Min. Typ. Max.

TLE7250XLE

TLE7250XSJ

Electrical Characteristics

Data Sheet 23 Rev. 1.0, 2015-08-12

CAN FD Characteristics

Received recessive bit width

at 2 MBit/s

tBit(RxD)_2

400 500 550 ns CL= 100 pF,

4.75 V < VCC < 5.25 V,

CRxD =15pF,

tBit = 500 ns,

(see Figure 12);

P_7.1.55

Transmitted recessive bit width

at 2 MBit/s

tBit(Bus)_2

435 500 530 ns CL= 100 pF,

4.75 V < VCC < 5.25 V,

CRxD =15pF,

tBit = 500 ns,

(see Figure 12);

P_7.1.56

Receiver timing symmetry

at 2 MBit/s

∆tRec =tBit(RxD) -tBit(Bus)

ΔtRec_2MB -65 – 40 ns CL= 100 pF,

4.75 V < VCC < 5.25 V,

CRxD =15pF,

tBit = 500 ns,

(see Figure 12);

P_7.1.57

1) Not subject to production test, specified by design.

2) In respect to common mode range.

Table 6 Electrical characteristics (cont’d)

4.5 V < VCC < 5.5 V; 3.0 V < VIO < 5.5 V; RL=60Ω; -40 °C < Tj< 150 °C; all voltages with respect to ground;

positive current flowing into pin; unless otherwise specified.

Parameter Symbol Values Unit Note / Test Condition Number

Min. Typ. Max.

TLE7250XLE

TLE7250XSJ

Electrical Characteristics

Data Sheet 24 Rev. 1.0, 2015-08-12

7.2 Diagrams

Figure 10 Test circuits for dynamic characteristics

Figure 11 Timing diagrams for dynamic characteristics

GND

100 nF

6CANL

7CANH

VCC

VIO

TxD

RxD

CRxD

100 nF

VDiff

TxD

RxD

0.9 V

tLoop(H,L)

td(L),T

td(L),R

0.5 V

tLoop(L,H)

td(H),T

td(H),R

0.3 x VIO

0.7 x VIO

TLE7250XLE

TLE7250XSJ

Electrical Characteristics

Data Sheet 25 Rev. 1.0, 2015-08-12

Figure 12 “Recessive” bit time - five “dominant” bits followed by one “recessive” bit

Diff

TxD

RxD

0.9 V

5 x t

Bit

0.5 V

Loop(H,L)

Bit

Bit(Bus)

Loop(L,H)

Bit(RxD)

0.3 x V

0.7 x V

0.3 x V

Diff

= V

CANH

- V

CANL

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 26 Rev. 1.0, 2015-08-12

8 Application Information

8.1 ESD Robustness according to IEC61000-4-2

Test for ESD robustness according to IEC61000-4-2 “Gun test” (150 pF, 330 Ω) have been performed. The results

and test conditions are available in a separate test report.

Table 7 ESD robustness according to IEC61000-4-2

Performed Test Result Unit Remarks

Electrostatic discharge voltage at pin CANH and

CANL versus GND

≥ +8 kV 1)Positive pulse

1) ESD susceptibility “ESD GUN” according to GIFT / ICT paper: “EMC Evaluation of CAN Transceivers, version 03/02/IEC

TS62228”, section 4.3. (DIN EN61000-4-2)

Tested by external test facility (IBEE Zwickau, EMC test report no. TBD).

Electrostatic discharge voltage at pin CANH and

CANL versus GND

≤ -8 kV 1)Negative pulse

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 27 Rev. 1.0, 2015-08-12

8.2 Application Example

Figure 13 Application circuit

example ECU design

BAT

TLE7250XLE

CANH

CANL

GND

TxD

RxD

Microcontroller

e.g. XC22xx

GND

Out

TLE4476D

GND

IQ1

100 nF

22 uF

EN Q2

22 uF

100 nF

TLE7250XLE

CANH

CANL

GND

TxD

RxD

Microcontroller

e.g. XC22xx

GND

Out

TLE4476D

GND

IQ1

100 nF 100 nF

22 uF

EN Q2

22 uF

100 nF

optional:

common mode choke

optional:

common mode choke

CANH CANL

120

Ohm

120

Ohm

CANH CANL

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 28 Rev. 1.0, 2015-08-12

8.3 Examples for Mode Changes

Changing the status on the RM input pin triggers a change of the operating mode, disregarding the actual signal

on the CANH, CANL and TxD pins (see also Chapter 4.2).

Mode changes are triggered by the RM pin, when the device TLE7250X is fully supplied. Setting the RM pin to

logical “low” changes the mode of operation to normal-operating mode:

• The mode change is executed independently of the signal on the HS CAN bus. The CANH, CANL inputs may

be either “dominant” or “recessive”. They can be also permanently shorted to GND or VCC.

• A mode change is performed independently of the signal on the TxD input. The TxD input may be either logical

“high” or “low”.

Analog to that, changing the RM input pin to logical “high” changes the mode of operation to the receive-only mode

independent on the signals at the CANH, CANL and TxD pins.

Note: In case the TxD signal is “low” setting the RM input pin to logical “low” changes the operating mode of the

device to normal-operating mode and drives a “dominant” signal to the HS CAN bus.

Note: The TxD time-out is only effective in normal-operating mode. The TxD time-out timer starts when the

TLE7250X enters normal-operating mode and the TxD input is set to logical “low”.

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 29 Rev. 1.0, 2015-08-12

8.3.1 Mode Change while the TxD Signal is “low”

The example in Figure 14 shows a mode change to normal-operating mode while the TxD input is logical “low”.

The HS CAN signal is “recessive”, assuming all other HS CAN bus subscribers are also sending a “recessive” bus

signal.

While the transceiver TLE7250X is in receive-only mode the transmitter is turned off. The TLE7250X drives no

signal to the HS CAN bus. The normal-mode receiver is active in receive-only mode and the RxD indicates the

“recessive” signal on the HS CAN bus with a logical “high” output signal.

Changing the RM to logical “low” turns the mode of operation to normal-operating mode, while the TxD input

remains logical “low”. The transmitter remains disabled until the mode change is completed. The normal-mode

receiver remains active also during the mode change. In normal-operating mode the transmitter becomes active

and the logical “low” signal on the TxD input drives a “dominant” signal to the HS CAN bus. The “dominant” bus

signal is indicated on the RxD output by a logical “low” signal.

Changing the RM pin back to logical “high”, disables the transmitter. The normal-mode receiver and the RxD

output remain active and the “recessive” bus signal is indicated on the RxD output by a logical “high” signal.

Figure 14 Example for a mode change while the TxD is “low”

RxD

VDIFF

TxD

t = tMode t = tMode

receive-only transition transition receive-onlynormal-operating

TxD input and transmitter

active

TxD input and transmitter

blocked TxD input and transmitter blocked

Note: The signals on the HS CAN bus are “recessive”, the “dominant” signal is

generated by the TxD input signal

normal-mode receiver and RxD output active

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 30 Rev. 1.0, 2015-08-12

8.3.2 Mode Change while the Bus Signal is “dominant”

The example in Figure 15 shows a mode change while the bus is “dominant” and the TxD input signal is set to

logical “high”.

While the transceiver TLE7250X is in receive-only mode the transmitter is turned off. The TLE7250X drives no

signal to the HS CAN bus. The normal-mode receiver is active in receive-only mode and the RxD indicates the

“dominant” signal on the HS CAN bus with a logical “low” output signal.

Changing the RM to logical “low” turns the mode of operation to normal-operating mode, while the TxD input

remains logical “high”. The transmitter remains disabled until the mode change is completed. The normal-mode

receiver remains active also during the mode change. In normal-operating mode the transmitter becomes active,

the bus remains “dominant” since the bus signal is driven from another HS CAN bus subscriber. The “dominant”

bus signal is indicated on the RxD output by a logical “low” signal.

Regardless which mode of operation is selected by the RM input pin, the RxD output indicates the signal on the

HS CAN bus. Also during the mode transition from receive-only mode to normal-operating mode or vice versa.

Figure 15 Example for a mode change while the HS CAN is “dominant”

RxD

VDIFF

TxD

t = tMode t = tMode

receive-only mode transition transition receive-only modenormal-operating

TxD input and transmitter

active

TxD input and transmitter blocked TxD input and transmitter blocked

Note: The “dominant” signal on the HS CAN bus is set by another HS CAN bus

subscriber.

normal-mode receiver and RxD output active

TLE7250XLE

TLE7250XSJ

Application Information

Data Sheet 31 Rev. 1.0, 2015-08-12

8.4 Further Application Information

• Please contact us for information regarding the pin FMEA.

• Existing application note.

• For further information you may visit: http://www.infineon.com/

TLE7250XLE

TLE7250XSJ

Package Outline

Data Sheet 32 Rev. 1.0, 2015-08-12

9 Package Outline

Figure 16 PG-TSON-8 (Plastic Thin Small Outline Nonleaded PG-TSON-8-1)

Figure 17 PG-DSO-8 (Plastic Dual Small Outline PG-DSO-8-44)

Green Product (RoHS compliant)

To meet the world-wide customer requirements for environmentally friendly products and to be compliant with

government regulations the device is available as a green product. Green products are RoHS compliant (i.e

Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).

±0.1

0.4

Pin 1 Marking Pin 1 Marking

PG-TSON-8-1-PO V01

±0.1

0.2

±0.1

0.25

0.81

±0.1

2.4

±0.1

0.1

±0.1

0.3

±0.1

0.38

±0.1

0.3

±0.1

0.65

±0.1

+0.05

±0.1

0.56

±0.1

1.63

±0.1

1.58

±0.1

0.05

0.07 MIN.

Z (4:1)

+0.06

0.19

0.35 x 45˚

-0.2

8 MAX.

0.64

±0.2

±0.25

0.2 8x

1.27

+0.1

0.41 0.2

-0.06

1.75 MAX.

(1.45)

±0.07

0.175

Index Marking

-0.21)

1) Does not include plastic or metal protrusion of 0.15 max. per side

2) Lead width can be 0.61 max. in dambar area

GPS01181

0.1

For further information on alternative packages, please visit our website:

http://www.infineon.com/packages.Dimensions in mm

TLE7250XLE
TLE7250XSJ
Revision History
 
Data Sheet 33 Rev. 1.0, 2015-08-12
 
10 Revision History
Revision Date Changes
1.0 2015-08-12 Data Sheet created.

Edition 2015-08-12

Published by

Infineon Technologies AG

81726 Munich, Germany

Legal Disclaimer

The information given in this document shall in no event be regarded as a guarantee of conditions or

characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any

information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties

and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights

of any third party.

Information

For further information on technology, delivery terms and conditions and prices, please contact the nearest

Infineon Technologies Office (www.infineon.com).

Warnings

Due to technical requirements, components may contain dangerous substances. For information on the types in

question, please contact the nearest Infineon Technologies Office.

Infineon Technologies components may be used in life-support devices or systems only with the express written

approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure

of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support

devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain

and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may

be endangered.