254872-000 - TE CONNECTIVITY

SPECIFICATION CONTROL DRAWING 44B5841

FOUR CONDUCTOR CABLE, SPIRALLY SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 12-27-11 F

This specication sheet forms a part of the latest issue of Raychem Specication 55A.

JACKET - RADIATION-CROSSLINKED,

MODIFIED ETFE

COMPONENT WIRES - 44A0811

CABLE RATINGS AND ADDITIONAL REQUIREMENTS

TITLE Date Revision

SHIELD - TIN-COATED COPPER

CABLE CONSTRUCTION DETAILS

PART NUMBER

CONDUCTOR

SIZE

(AWG)

SHIELD

SIZE

(AWG)

JACKET THICKNESS

(in.)

OUTSIDE DIAMETER

(in.) MAXIMUM

WEIGHT

(lbs/1000 ft.)

MINIMUM NOMINAL NOMINAL MAXIMUM

44B5841-10-* 10 36 .008 .010 .406 .480 172.

44B5841- 8-* 8 34 .010 .012 .556 .658 301.

44B5841- 6-* 6 34 .013 .015 .683 .809 466.

44B5841- 4-* 4 34 .016 .018 .824 .977 705.

44B5841- 2-* 2 34 .020 .023 1.03 1.22 1122.

TEMPERATURE RATING: 150°C

Maximum continuous conductor temperature

VOLTAGE RATING: 600 volts (rms) at sea level

ACCELERATED AGING: 300 ± 3°C for 7 hours

BLOCKING: 150 ± 3°C for 6 hours

DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute

FLAMMABILITY (Procedure 1): 3 seconds (maximum);

3 in. (maximum); no aming of facial tissue

JACKET COLOR: White preferred

JACKET ELONGATION AND TENSILE STRENGTH:

Elongation, 50% (minimum)

Tensile Strength, 5000 lbf/in² (minimum)

JACKET FLAWS:

Spark Test, 1.0 kV (rms)

Impulse Dielectric Test, 6.0 kV (peak)

NOTE: Nominal values are for information only.

Nominal values are not requirements.

LIFE CYCLE: 200 ± 3°C for 168 hours

LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours

SHIELD COVERAGE: 85% (minimum)

VOLTAGE WITHSTAND TEST (Post Environmental):

1000 volts (rms), 60 Hz, 1 minute

WRAP: .001 inch thick (nominal), 25% overlap (minimum)

PART NUMBER:

The “*” in the part numbers above shall be replaced by color code

designators with a slash separating the component wire colors and a

dash separating the component wire colors from the jacket color.

Colors shown do not necessarily reect the sequence of manufacturing.

1/ Example: AWG 10, black, brown, red and orange component wires;

white jacket: 44B5841-10-0/1/2/3-9

HIGH TEMPERATURE TAPE

(optional)

Users should evaluate the suitability of this product for their application. Specications are subject to change without notice.

Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specication, without notication to Buyer.

1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,

AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND

SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.

Page 1 of 1

Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Raychem Wire & Cable

501 Oakside Avenue

Redwood City, CA 94063-3800

Phone: 1-800-227-8816

Fax: 1-650-361-6297

DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.

THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.

REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.