PLED Open LED Protectors High power PLED PLEDxUSWxA Series - Unidirectional, White Body e3 RoHS Description PLEDxUSWxA open LED protectors provide a switching electronic shunt path when an LED in an electronic switching fails as an open circuit. This ensures that the remaining string of LEDs will continue to function if a single LED does not. The devices is designed to enable higher reliability in indoor LED lighting applications such as advertisement lighting and other applications. Additionally, it is molded from white material to make them less visible in the LED fixture and the white molding also reflects more light to improve overall light engine efficiency. This series is compatible with one, two and three watt LEDs that have a nominal 3V forward characteristic and is available in an SMB, PLEDxUSWxA is available in SMB surface mount package. The DO-214AA (SMB) low profile package is ideal for dense board applications. Agency Approvals Agency Agency File Number E133083 Schematic Symbol Features & Benefits MT2 * Ideal for protecting high brightness LED with high operating current at specified condition. * IEC-61000-4-2 ESD 30kV (Air), 30kV (Contact) * Reverse Battery/Power Protection * RoHS compliant and halogen-free * Low profile, small foot print standard DO-214AA package * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) * ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * White compound for better optical appearances * Compatible with PWM frequencies up to 30 kHz * Fast switching Control Circuit MT1 Cathode (bar marking side) * Compatible with industrial lighting environments Electrical Characteristics (All parameters are measured at T=25C unless otherwise noted) Part Number PLED6USW2A VBR breakdown VDRM breakdown IH IS IT@VT VT @ IT = 1 Amp IO 1 Critical rate of rise dV/dt Volts Volts mAmps mAmps Amps Volts Amps Volts Marking PL62A Min Max Min Min Max Max Max Max Max 6 16 6 5 100 1.0 1.2 2 250V/s PLED6USW3A PL63A 6 16 6 5 100 1.0 1.2 3 250V/s PLED9USW3A PL93A 9 18 9 5 100 1.0 1.2 3 250V/s Notes: 1. IO- Operation current tested @ aluminum boards, ambient temp 85C (c)2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/06/18 PLED Open LED Protectors High power PLED Thermal Considerations Package DO-214AA in White Symbol Parameter Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C RJA Thermal Resistance: Junction to Ambient DO-214AA: 901 DO-214AA: 402 C/W Notes: 1) Standard FR-4 PCB with Copper Pads (Recommended Size) 2) Aluminum PCB Thickness: 1.6mm Grade: 1-2 W/mK Thermal Conductivity Trace thickness: 2 oz Insulation layer thickness: 215 um Solder Pad Dimensions: 2.0mm x 2.8mm (Recommended Size) V-I Characteristics VT vs. IT +I 25 IS IH VF -V +V VT VDRM VBR Precent of VT Change - % IT 20 15 10 5 0 0.5 IT 1.0 1.5 2.0 -I 3.0 2.0 1.8 VBR vs. Junction Temperature 14 P e rc e n t o f VBR C h a n g e - % iH (T C = 2 5 C ) R a tio o f iH Normalized DC Holding Current vs. Case Temperature 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 2.5 IT - A 0 20 40 60 80 100 120 140 160 Case Temperature (T C ) - C (c)2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/06/18 12 10 8 6 25 C 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ ) - C 3.5 PLED Open LED Protectors High power PLED LED Interference Test Circuit Q1 LED Driver 2.0 , 1/4 W 110 k, 1/4 W + - Vbat 12 Vdc Q2 2N2222 PWM MT2 Unidiretional PLED Control Circuit ON/OFF Switch 6 LEDs in Series 50% Duty Cycle 10kHz MT1 5 LEDs and 1 PLED in Series 50% Duty Cycle 10kHz Note: These two graphs show the current magnitude through the LED string with and without the PLED included. There is no noticeable effect on the LED current magnitude when the PLED is included in the circuit as compared to the LED current magnitude when the PLED is not in the circuit. (The conversion factor for the test measurement in the graphs above is 10mA/mV for the Pearson coil measurement, therefore, the current magnitude in the first figure is 10mA*8.9 = 89mA, while the second figure is 91mA.) PLED in the Off-State 10kHz Channel 1: current through LEDs (318 mA) Channel 2: voltage across PLED device (4.5 V) (c)2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/06/18 PLED device zeners and then turns fully on 10kHz Channel 1: current through LEDs (346 mA) and PLED device once it is fully turned on 2.5 sec later Channel 2: voltage across PLED device (21.3 V before PLED crowbars with 2 V drop) PLED Open LED Protectors High power PLED Soldering Parameters Pb - Free assembly Reflow Condition Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max 3C/second max TS(max) to TL - Ramp-up Rate Reflow 217C - Temperature (TL) (Liquidus) 60 - 150 seconds - Temperature (tL) Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 30 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes max Do not exceed 260C Physical Specifications Terminal Material Copper Alloy Terminal Finish 100% Matte Tin Plated Body Material UL recognized compound meeting flammability classification V-0 Environmental Specifications High Temperature Voltage Blocking MIL-STD-750: Method 1040, Condition A 80% min VDRM (VAC-peak), 150C, 504 hours Temperature Cycling MIL-STD-750: Method 1051 -65C to 150C, 15-minute dwell, 100 cycles Biased Temperature & Humidity EIA/JEDEC: JESD22-A101 80%VDRM, 85C, 85%RH, 1008 hours High Temperature Storage MIL-STD-750: Method 1031 150C, 1008 hours Low Temperature Storage -65C, 1008 hours Thermal Shock MIL-STD-750: Method 1056 0C to 100C, 5-minute dwell, 10-second transfer, 10 cycles Resistance to Solder Heat MIL-STD-750: Method 2031 260C, 10 seconds Packaging Package Description Packaging Quantity Industry Standard S D O - 2 1 4 AA 2500 EIA-481-1 Part Numbering System Part Marking System DO-214AA PLED 6 U S W 2A PLxxA PLxU Operating Current TYPE PLED: LED Protector V DRM 6: 6 Volts Unidirectional XXXXX 2: 2 Amp White molded Cathode Bar PACKAGE TYPE S: DO-214AA QFN PLxU XXXXX (c)2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/06/18 Cathode Bar to Indicate Diode Direction PLED Open LED Protectors High power PLED Dimensions - DO-214 AA Package B CASE TEMPERATURE MEASURING POINT D A C K Dimensions H F E G 0.079" (2.0mm) Inches Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 0.110" (2.8mm) 0.079" (2.0mm) Recommended solder pad layout (Reference Only) DO-214AA Embossed Carrier Reel Pack (RP) Meets all EIA-481-1 Standards 0.157 (4.0) 0.472 (12.0) Cathode bar on this side 0.36 (9.2) 0.315 (8.0) 0.512 (13.0) Arbor Hole Dia. 0.059 DIA (1.5) Cover tape 12.99 (330.0) Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. (c)2018 Littelfuse, Inc. Specifications are subject to change without notice. Revision: 03/06/18