MB90F546GSPFR-GE1 - SPANSION

industrial.panasonic.com/ac/e/ ASCTB383E 201903

2019.03

ORDERING INFORMATION

TYPICAL APPLICATIONSFEATURES

DJ-H RELAYS (ADJH)

Suitable for lighting and

motor load, 1 Form A 50A

latching relays

1. High inrush capability

2. Supports manual operation

1. Smart house

(Shutter and Sunblind control)

2. Lighting control

3939 1515

30.2

3939

30.230.2

1515

Protective construction

：

Flux-resistant type

（

Unit

：

）

Standard type Manual switch type

• Tungsten load (TV-20 class)

• Electronic ballast load (NEMA410)

• Capacitive load (IEC60669-1)

• Manual switch type available

2ADJH

Rated voltage

（DC）

05 :5V, 12 :12V, 24 :24V

Contact arrangement

2:1 Form A

Type classification

0：Standard type

（Without manual switch）

1：Manual switch type

Operating function

1:1 coil latching

2:1 coil latching

（Reverse polarity）

3:2 coil latching

4:2 coil latching

（Reverse polarity）

*Reverse polarity type available. (1 coil latching type: ADJH220**, 2 coil latching type: ADJH240**)

TYPES

1. Standard type (Without manual switch)

Contact arrangement Rated voltage Part No. Standard packing

1 coil latching type 2 coil latching type Carton Case

1 Form A

5V DC ADJH21005 ADJH23005

50 pcs. 200 pcs.12V DC ADJH21012 ADJH23012

24V DC ADJH21024 ADJH23024

Automation Controls Catalog

DJ-H (ADJH2)

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/

*Reverse polarity type available. (1 coil latching type: ADJH221**, 2 coil latching type: ADJH241**)

2. Manual switch type

RATING

1.Coil data

• Operating characteristics such as ‘Operate voltage’ and ‘Release voltage’ are inuenced by mounting conditions, ambient temperature, etc.

Therefore, please use the relay within ± 5% of rated coil voltage.

• ‘Initial’ means the condition of products at the time of delivery.

1) 1 coil latching type

Rated voltage Set voltage

(at 20°C 68°F)*1

Reset voltage

(at 20°C 68°F)*1

Rated operating current

[±10%] (at 20°C 68°F)

Coil resistance

[±10%] (at 20°C 68°F)Rated operating power Max. allowable voltage

(at 20°C 68°F)

Set coil Reset coil Set coil Reset coil

5V DC Max. 75% or less of

rated voltage

(Initial)

Max. 75% or less of

rated voltage

(Initial)

200 mA 200 mA 25Ω 25Ω

1,000mW 130% of rated voltage12V DC 83.3mA 83.3mA 144Ω 144Ω

24V DC 41.7mA 41.7mA 576Ω 576Ω

*1. Square, pulse drive

2. Specications

2) 2 coil latching type

*1. Square, pulse drive

Rated voltage Set voltage

(at 20°C 68°F)*1

Reset voltage

(at 20°C 68°F)*1

Rated operating current

[±10%] (at 20°C 68°F)

Coil resistance

[±10%] (at 20°C 68°F)Rated operating power Max. allowable voltage

(at 20°C 68°F)

Set coil Reset coil Set coil Reset coil

5V DC Max. 75% or less of

rated voltage

(Initial)

Max. 75% or less of

rated voltage

(Initial)

400 mA 400 mA 12.5Ω 12.5Ω

2,000mW 130% of rated voltage12V DC 166.7mA 166.7mA 72 Ω 72 Ω

24V DC 83.3mA 83.3mA 288 Ω 288 Ω

Characteristics Item Specications

Contact data

Arrangement 1 Form A

Contact resistance (initial) Max. 20 mΩ (by voltage drop 24 V DC 1A)

Contact material AgSnO2 type

Contact rating (resistive) 50A 277V AC

Max. switching power (resistive) 13,850 VA (50A 277V AC)

Max. switching voltage 480V AC

Max. switching current 50A (AC)

Min. switching load (reference value)*1100mA 5 V DC

Insulation resistance (initial) Min. 1,000MΩ (at 500V DC) Measured portion is the same as the case of dielectric voltage

Dielectric strength

(initial)

Between open contacts 1,500 Vrms for 1min. (Detection current: 10mA)

Between contact and coil 4,000 Vrms for 1min. (Detection current: 10mA)

Surge withstand

voltage*2 (initial) Between contact and coil 12,000 V

Set time (initial) Max. 20ms (at rated voltage, at 20°C 68°F, without bounce)

Reset time (initial) Max. 20ms (at rated voltage, at 20°C 68°F, without bounce)

Shock resistance Functional 100 m/s2 (half-sine shock pulse: 11 ms, detection time: 10µs)

Destructive 1,000 m/s2 (half-sine shock pulse: 6 ms)

Vibration resistance Functional 10 to 55 Hz at double amplitude of 1.5 mm (detection time: 10µs)

Destructive 10 to 55 Hz at double amplitude of 2.0 mm

Expected life Mechanical Min. 1×106 (at 180 times/min.)

Conditions Conditions for operation, transport and

storage*3Ambient Temperature: –40 to +85°C –40 to +185°F

Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)

Unit weight Approx. 31 g 1.09 oz

Notes: *1. Minimum switching load is a guide to the lower current limit of switching under the micro-load. This parameter is changed by the condition, such as switching times,

environment condition, and expected reliability. When the relay is used lower than minimum switching load, reliability is attrition. Please use the relay over minimum

switching load.

*2. Wave is standard shock voltage of ±1.2×50μs according to JEC-212-1981

*3. Allowable range when in original packaging is –40 to +70°C –40 to +158°F.

3. Expected electrical life

Type Load Switching capacity Number of operations

1 Form A

Resistive 50A 277V AC Min. 1 × 104 (ON:OFF = 1s:9s)

25A 277V AC Min. 1 × 105 (ON:OFF = 1s:9s)

Inrush

load

Tungsten 2,400W 120V AC Min. 2.5 × 104 (ON:OFF = 1s:59s)

Electronic ballast 20A 277V AC Min. 6 × 103 (ON:OFF = 1s:9s)

Capacitive (IEC 60669-1) 20A 250V AC 200µF Min. 3 × 104 (ON:OFF = 1s:9s)

Contact arrangement Rated voltage Part No. Standard packing

1 coil latching type 2 coil latching type Carton Case

1 Form A

5V DC ADJH21105 ADJH23105

50 pcs. 200 pcs.12V DC ADJH21112 ADJH23112

24V DC ADJH21124 ADJH23124

DJ-H (ADJH2)

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/ © Panasonic Corporation 2019 ASCTB383E 201903

4. Inrush load (Electrical life diagram)

Load Tungsten Electronic ballast Capacitive (IEC 60669-1)

Switching

capacity 2,400W 120V AC 20A 277V AC 20A 250V AC 200µF

Load

voltage 120V AC (60Hz) 277V AC (60Hz) 250V AC (60Hz)

Load

current

Inrush 250AO-P

Steady-state 20Arms

Inrush 480AO-P

Steady-state 16Arms

Inrush 400AO-P

Steady-state 20Arms

Circuit

Current

waveform

60Hz

Rated voltage

N.O.

Relay

120V AC

1,250

60Hz

Rated voltage

N.O.

Relay

277V AC

0.25

200μ

60Hz

Rated voltage

N.O.

Relay

250V AC

Tek M Pos：3.800ms

R Relay

CH1 100A CH1

M 5.00ms

100A/div

5ms/div

Tek ●Acq Complete M Pos：11.52ms

CH2 200A CH1

M 500

200A/div

500

s/div

Tek ●Acq Complete M Pos：6.480ms

CH1 200A CH2 200A CH1

M 250

200A/div

250

s/div

DJ-H (ADJH2)

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/

DIMENSIONS (mm)

PC board pattern (Bottom view)

External dimensions

Tolerance: ±0.1 ±.004

Schematic (Bottom view)

1. Standard type (Without manual switch)

2 or 3ｰ□0.64

＋0.5

－0.3

coil latching type only

2 coil latching

type only

27.5 6.751.85

0.4

30.2

7.5

1.5

1.6 1.6

General tolerance ±0.3

7.5

27.5 6.75

2 coil latching type only

2 or 3ｰ1.2dia.

2ｰ2.8dia.

Tolerance ±0.1

2（＋）

1（－）

2（－）

1（＋）

2（－）

1（－）

5（＋）

2（－）

1（－）

5（＋）

1 coil latching type 2 coil latching type

1 coil latching type

(Reverse polarity)

2 coil latching type

(Reverse polarity)

PC board pattern (Bottom view)

External dimensions

Schematic (Bottom view)

2. Manual switch type

2 or 3ｰ□0.64

5.8

5.3

13.6

27.5 6.751.85

Ｍａｘ .3.1

0.4

30.2

7.5

1.5

1.6 1.6

5＋0.5

－0.3

coil latching type only

2 coil latching

type only

General tolerance ±0.3

7.5

27.5 6.75

2 coil latching type only

2 or 3ｰ1.2dia.

2ｰ2.8dia.

Tolerance ±0.1

2（＋）

1（－）

2（－）

1（＋）

2（－）

1（－）

5（＋）

2（－）

1（－）

5（＋）

1 coil latching type 2 coil latching type

1 coil latching type

(Reverse polarity)

2 coil latching type

(Reverse polarity)

SAFETY STANDARDS

UL/C-UL (Recognized) VDE

File No. Contact rating Cycles Temperature File No. Contact rating Cycles Temperature

E43149

50A 277V AC Resistive 10485°C 185°F

40045659

50A 250V AC (cosφ =1.0) 10485°C 185°F40A 347V AC Resistive 2 × 10440°C 104°F

30A 480V AC Resistive 2 × 10440°C 104°F

20A 347V AC Electronic ballast

(1 coil latching type only) 6 × 103

40°C

104°F 25A 250V AC (cosφ =1.0) 9 × 10440°C 104°F

20A 277V AC Electronic ballast 6 × 10385°C 185°F

20A 277V AC Standard ballast 3 × 10485°C 185°F

20A 250V AC Capacitor 200µF

(IEC60669-1 compliant) 5 × 10340°C 104°F15A 347V AC Standard ballast 3 × 10485°C 185°F

5,540W 277V AC Tungsten 2.5 × 10440°C 104°F

CAD

CAD The CAD data of the products with a “CAD” mark can be downloaded from our Website.

DJ-H (ADJH2)

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/ © Panasonic Corporation 2019 ASCTB383E 201903

INSULATION CHARACTERISTICS (IEC61810-1)

NOTES

1. For cautions for use, please read

“GENERAL APPLICATION

GUIDELINES”.

2. Regarding the set/reset pulse time

of the latching type relay, it is

recommended to apply rated

voltage for minimum 100ms pulse

across the coil to secure the sure

operation considering the ambient

temperature and condition change

through service life.

Please refer to "the latest product specications"

when designing your product.

• Requests to customers :

https://industrial.panasonic.com/ac/e/salespolicies/

Item Characteristics

Clearance/Creepage distance (IEC61810-1) 9.5mm/12.7mm

Category of protection (IEC61810-1) RT II

Tracking resistance (IEC60112) 175V

Insulation material group III a

Over voltage category III

Rated voltage 250 V

Pollution degree 2

Type of insulation (Between contact and coil) 4,000 V

Type of insulation (Between open contacts) 1,500 V

Panasonic Corporation 2019

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/ -1-

Humidity, %R.H.

Allowable range

0 85–40

(Avoid

condensation

when used at

temperatures

higher than

0°C

(Avoid icing

when used at

temperatures

lower than 0°C)

Ambient temperature, °C

)

GUIDELINES FOR POWER RELAYS AND HIGH-CAPACITY DC CUT OFF RELAYS USAGE

Long term current carrying

A circuit that will be carrying a current continuously for long periods

without relay switching operation. (circuits for emergency lamps, alarm

devices and error inspection that, for example, revert only during

malfunction and output warnings with form B contacts) Continuous,

long-term current to the coil will facilitate deterioration of coil insulation

and characteristics due to heating of the coil itself.

For circuits such as these, please use a magnetic-hold type latching

relay. If you need to use a single stable relay, use a sealed type relay

that is not easily a󰀨ected by ambient conditions and make a failsafe

circuit design that considers the possibility of contact failure or

disconnection.

DC Coil operating power

Steady state DC current should be applied to the coil. The wave form

should be rectangular. If it includes ripple, the ripple factor should be

less than 5%.

However, please check with the actual circuit since the electrical

characteristics may vary. The rated coil voltage should be applied to

the coil and the set/reset pulse time of latching type relay di󰀨ers for

each relays, please refer to the relay's individual specications.

Coil connection

When connecting coils of polarized relays, please check coil polarity

(+,-) at the internal connection diagram (Schematic). If any wrong

connection is made, it may cause unexpected malfunction, like

abnormal heat, re and so on, and circuit do not work. Avoid

impressing voltages to the set coil and reset coil at the same time.

Usage, Transport, and Storage Conditions

During usage, storage, or transportation, avoid locations

subjected to direct sunlight and maintain normal temperature,

humidity and pressure conditions.

Temperature/Humidity/Pressure

When transporting or storing relays while they are tube

packaged, there are cases the temperature may di󰀨er from the

allowable range. In this case be sure to check the individual

specications. Also allowable humidity level is inuenced by

temperature, please check charts shown below and use relays

within mentioned conditions. (Allowable temperature values

di󰀨er for each relays, please refer to the relay's individual

specications.)

Maximum allowable voltage and temperature rise

Proper usage requires that the rated coil voltage be impressed on the

coil. Note, however, that if a voltage greater than or equal to the

maximum continuous voltage is impressed on the coil, the coil may

burn or its layers short due to the temperature rise. Furthermore, do

not exceed the usable ambient temperature range listed in the catalog.

Operate voltage change due to coil temperature rise

(Hot start)

In DC relays, after continuous passage of current in the coil, if the

current is turned OFF, then immediately turned ON again, due to the

temperature rise in the coil, the pick-up voltage will become somewhat

higher. Also, it will be the same as using it in a higher temperature

atmosphere. The resistance/temperature relationship for copper wire

is about 0.4% for 1°C, and with this ratio the coil resistance increases.

That is, in order to operate of the relay, it is necessary that the voltage

be higher than the pick-up voltage and the pick-up voltage rises in

accordance with the increase in the resistance value. However, for

some polarized relays, this rate of change is considerably smaller.

Precautions for Coil Input

Ambient Environment

For cautions for use, please read “GUIDELINES FOR RELAY USAGE”.

https://industrial.panasonic.com/ac/e/control/relay/cautions_use/index.jsp

1) Temperature:

The tolerance temperature range differs for each relays,

please refer to the relay’s individual specifications

2) Humidity:

5 to 85 % RH

3) Pressure:

86 to 106 kPa

Dew condensation

Condensation occurs when the ambient temperature drops

suddenly from a high temperature and humidity, or the relay is

suddenly transferred from a low ambient temperature to a high

temperature and humidity. Condensation causes the failures like

insulation deterioration, wire disconnection and rust etc.

Panasonic Corporation does not guarantee the failures caused

by condensation.

The heat conduction by the equipment may accelerate the

cooling of device itself, and the condensation may occur.

Please conduct product evaluations in the worst condition of

the actual usage. (Special attention should be paid when high

temperature heating parts are close to the device. Also please

consider the condensation may occur inside of the device.)

Icing

Condensation or other moisture may freeze on relays when the

temperature become lower than 0°C.This icing causes the sticking of

movable portion, the operation delay and the contact conduction failure

etc. Panasonic Corporation does not guarantee the failures caused by

the icing.

The heat conduction by the equipment may accelerate the cooling of

relay itself and the icing may occur. Please conduct product

evaluations in the worst condition of the actual usage.

Low temperature and low humidity

The plastic becomes brittle if the switch is exposed to a low

temperature, low humidity environment for long periods of time.

High temperature and high humidity

Storage for extended periods of time (including transportation periods)

at high temperature or high humidity levels or in atmospheres with

organic gases or sulde gases may cause a sulde lm or oxide lm to

form on the surfaces of the contacts and/or it may interfere with the

functions. Check out the atmosphere in which the units are to be

stored and transported.

ASCTB412E 201903

Panasonic Corporation Electromechanical Control Business Division

industrial.panasonic.com/ac/e/ Panasonic Corporation 2019

-2-

GUIDELINES FOR POWER RELAYS AND HIGH-CAPACITY DC CUT OFF RELAYS USAGE

Package

In terms of the packing format used, make every e󰀨ort to keep the

e󰀨ects of moisture, organic gases and sulde gases to the absolute

minimum.

Silicon

When a source of silicone substances (silicone rubber, silicone oil,

silicone coating materials and silicone lling materials etc.) is used

around the relay, the silicone gas (low molecular siloxane etc.) may be

produced.

This silicone gas may penetrate into the inside of the relay. When the

relay is kept and used in this condition, silicone compound may adhere

to the relay contacts which may cause the contact failure. Do not use

any sources of silicone gas around the relay (Including plastic seal

types).

Others

Cleaning

1) Although the environmentally sealed type relay (plastic sealed type,

etc.) can be cleaned, avoid immersing the relay into cold liquid (such

as cleaning solvent) immediately after soldering. Doing so may

deteriorate the sealing performance.

2) Cleaning with the boiling method is recommended(The temperature

of cleaning liquid should be 40°C or lower ).

Avoid ultrasonic cleaning on relays. Use of ultrasonic cleaning may

cause breaks in the coil or slight sticking of the contacts due to

ultrasonic energy.

Please refer to "the latest product specications"

when designing your product.

•Requests to customers:

https://industrial.panasonic.com/ac/e/salespolicies/

NOx Generation

When relay is used in an atmosphere high in humidity to switch a load

which easily produces an arc, the NOx created by the arc and the

water absorbed from outside the relay combine to produce nitric acid.

This corrodes the internal metal parts and adversely a󰀨ects operation.

Avoid use at an ambient humidity of 85%RH or higher (at 20°C). If use

at high humidity is unavoidable, please contact our sales

representative.

ASCTB412E 201903

2019

ASCTB383E-1 201903