UNISONIC TECHNOLOGIES CO., LTD LR18120 CMOS IC 2A LOW DROPOUT REGULATOR WITH ENABLE DESCRIPTION The UTC LR18120 is a positive voltage regulator with high performance. It has low dropout voltage and low input voltage, besides its output voltage can be fixed at 1.2V, 1.5V, 1.8V, or 2.5V depending on internal feedback resistors or ADJ (not connected to the ground) with external feedback resistors. The input voltage of UTC LR18120 can be low to 1.4V. There are two additional pin in the LR18120. One is EN pin and the other is POK pin. The UTC LR18120 is specially made for applications with low input voltage, low dropout voltage, and low output voltage which is almost the same as the input voltage. Typical applications include motherboards, notebooks, set top boxes, network cards and peripheral cards. FEATURES * VIN as Low as 1.4V and VPP Voltage 5V * VD=320mV @ IOUT=2A, VOUT=1.2V * Internal Over Current and Over Temperature Protection * With Enable Pin * Output Voltage: 2% * 1.2V, 1.5V, 1.8V and 2.5V Output Voltage Adjustable Externally Using Resistors * When Disable VOUT Pull Low Resistance ORDERING INFORMATION Ordering Number Lead Free Halogen Free LR18120xL-xx-S08-R LR18120xG-xx-S08-R LR18120xL-xx-SH2-R LR18120xG-xx-SH2-R www.unisonic.com.tw Copyright (c) 2012 Unisonic Technologies Co., Ltd Package Packing SOP-8 HSOP-8 Tape Reel Tape Reel 1 of 8 QW-R502-305.E LR18120 CMOS IC MARKING INFORMATION PACKAGE VOLTAGE CODE SOP-8 HSOP-8 12:1.2V 15:1.5V 18:1.8V 25:2.5V PIN CONFIGURATION PIN DESCRIPTION PIN NO. PIN NAME 1 POK 2 VEN 3 VIN 4 5 6 VPP NC VOUT 7 ADJ 8 GND MARKING DESCRIPTION This pin will Indicate high under this situation: VO reaches 92% of its rating voltage. Open-drain output. The enable control Input pin. As while as this pin's voltage falls below 0.4V ,the LR18120 will stop working. When there's nothing connected with this pin, for active High version, the device will be enabled, for active Low versionthe device will be shutdowned The pin of input voltage. Placing large capacitance closely to this pin is necessary. There should be connected a 10F ceramic capacitor. This pin is for input voltage to control circuit. Connected nothing. The voltage output pin. When this pin connected to the ground,VOUT will be set by the internal feedback resistors. Otherwise, if using external feedback resistors to decide the VOUT, VOUT = 0.8(R1+R2)/R2 Volts. Ground. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 8 QW-R502-305.E LR18120 CMOS IC BLOCK DIAGRAM Enable Threshold Level High: + + + - + - - - Enable Threshold Level Low: UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 8 QW-R502-305.E LR18120 CMOS IC ABSOLUTE MAXIMUM RATING PARAMETER SYMBOL RATINGS Input Voltage VPP, VIN 7 Power Dissipation PD Internally limited Junction Temperature TJ 150 Ambient Operation Temperature TOPR -40~ +85 Storage Temperature TSTG -65~ +150 Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. C C C RECOMMENDED OPERATING CONDITIONS PARAMETER VIN Voltage VPP Voltage Ambient Operation Temperature UNIT V SYMBOL VIN VPP TOPR RATINGS 1.4 ~5.5 4.5~5.5 -40C TOPR +85C UNIT V V C SYMBOL RATINGS 150 143 20 14 UNIT C/W C/W C/W C/W THERMAL DATA PARAMETER Junction to Ambient Junction to Case SOP-8 HSOP-8 SOP-8 HSOP-8 JA JC ELECTRICAL CHARACTERISTICS VPP=5V, VIN =3.3V, VEN=VPP, IOUT =10mA, CIN=10F, COUT =10F, TA=TJ=25C, unless otherwise specified. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX VIN Input Voltage Range VIN 1.4 5.5 Quiescent Current (Ground Current) IQ VOUT=2.5V 1 2 VPP VPP Voltage Range VPP 4.5 5.5 VOUT =2.5V 0.23 0.5 IPPH VPP Current IPPL VEN=0V 36 60 VOUT Output Voltage (Internal Fixed Voltage) VOUT VIN= VOUT +0.5V, VOUT =2.5V 2.45 2.5 2.55 Line Regulation VOUT VIN x VOUT VIN=( VOUT +0.5V) ~ 5V 0.2 1 UNIT V mA V mA A V % Load Regulation VOUT 10mAIOUT2A 0.2 1 % Dropout Voltage VD IOUT=2A 300 420 mV Short Circuit Current 1.4 A VOUT Pull Low Resistance VEN=0V 90 ADJ Reference Voltage VREF VADJ= VOUT 0.788 0.8 0.812 V Adjust Pin Current IADJ 20 100 nA Adjust Pin Threshold 0.15 0.2 0.25 V VEN VEN Pin Voltage High VH(EN) 1.6 V VEN Pin Voltage Low VL(EN) 0.4 V VEN Pin Bias Current IBIAS(EN) VEN=0V 12 40 A POK VOUT Power OK Voltage VTHPOK 92 % Hysteresis VHYPOK 7 % OVER TEMPERATURE PROTECTION Over Temperature TOT 150 C Over Temperature Hysteresis TOTHY 30 C Note: Low duty pulse techniques are used during test to maintain junction temperature as close to ambient as possible. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 8 QW-R502-305.E LR18120 CMOS IC TYPICAL APPLICATION CIRCUIT 0.8(R1 + R2) R2 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 8 QW-R502-305.E LR18120 CMOS IC TYPICAL CHARACTERISTICS (VCC= 3.3V, TA=25C, unless otherwise specified.) 1 0.9 0.9 Quiescent Current, IQ (mA) Quiescent Current, IQ (mA) Quiescent Current vs. Input Voltage 1 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.6 0.5 0.4 0.3 0.2 0 -45-35-25-15 -5 5 15 25 35 45 55 65 75 85 Temperature (C) 0 3 3.5 4 4.5 5 Input Voltage, VIN (v) 5.5 IPPH Current vs. Input Voltage 0.5 IPPH Current vs. Temperature 0.5 0.45 0.45 0.4 0.4 IPPH Current, IIPPH (mA) IPPH Current, IIPPH (mA) 0.8 0.7 0.1 0.1 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 3 3.5 4 4.5 5 0 -45-35-25-15 -5 5 15 25 35 45 55 65 75 85 Temperature (C) 5.5 Input Voltage, VIN (v) IPPL Current vs. Temperature IPPL Current vs. Input Voltage 40 40 35 35 30 30 IPPL Current, IIPPL (A) IPPL Current, IIPPL (A) Quiescent Current vs. Temperature 25 20 15 10 5 25 20 15 10 5 0 3 3.5 4 4.5 5 5.5 Input Voltage, VIN (v) UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 0 -45-35-25-15 -5 5 15 25 35 45 55 65 75 85 Temperature (C) 6 of 8 QW-R502-305.E LR18120 CMOS IC TYPICAL CHARACTERISTICS(Cont.) Output Voltage vs. Input Voltage 2.55 Reference Voltage, VREF (V) Output Voltage, VO (V) 2.54 2.53 2.52 IO=0A 2.51 Reference Voltage vs. Input Voltage 0.812 2.5 2.49 2.48 2.47 0.808 0.804 0.8 0.796 0.792 2.46 0.788 2.45 3 3.5 3 5.5 2.5 2 1.5 1 0.5 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 4.5 5 5.5 Max. Power Dissipation vs.TAMB (still air) A=5.0 in2 3 2.5 A=4.5 in2 A=4.0 in2 A=3.5 in2 A=3.0 in2 2 1.5 1 A=1.0 in2 A=1.5 in2 A=2.0 in2 0.5 0 25 35 PCB Top Copper Area (in2) Load Transient Stop 4 3.5 Max. Dissipation Power, PD (W) 3 3.5 Input Voltage, VIN (v) Max. Power Dissipation vs. PCB Top Copper Area 3.5 Max. Dissipation Power, PD (W) 4 4.5 5 Input Voltage, VIN (v) 45 A=2.5 in2 A=0.5 in2 55 35 TAMB (C) 75 85 Short Circuit Current Stop VOUT IOUT VIN=3.3V,VOUT=2.5V,IOUT=0 to 2A UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 8 QW-R502-305.E LR18120 CMOS IC TYPICAL CHARACTERISTICS(Cont.) VIN Start up Waveform VPP Start up Waveform Tek Stop Stop VIN VOUT VPP VPP VOUT VIN VEN Start up Waveform Tek Stop VEN VOUT VPP VIN UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 8 of 8 QW-R502-305.E