Models PT-10 and PT-20
www.vishay.com Vishay Dale
Not for New Designs
Revision: 08-Aug-16 1Document Number: 34073
For technical questions, contact: magnetics@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Through-Hole Transformers
Pulse, Trigger Type
FEATURES
• Choice of printed circuit or bobbin-type
configurations
• Designed to transfer high amplitude or long
duration pulses without saturation
• Designed for low-cost trigger source isolation in half and
full wave SCR power control circuits, including motor
speed controls, heater controls and incandescent lighting
controls
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
(1) Standard items in PT-10 Model. Other dash numbers available on request. All dash numbers standard in PT-20 model
ELECTRICAL SPECIFICATIONS
Primary inductance values: from 200 μH to 5000 μH
Turns ratio: 1:1, 1:1:1, 2:1, 2:1:1 and 5:1
Temperature range: -10 °C to +70 °C
Dielectric test at 60 Hz: 1600 VRMS (windings to case)
AC line voltage at 60 Hz: 240 VRMS maximum in test circuits
shown
MATERIAL SPECIFICATIONS
Bobbin: nylon
Leads: tinned, solderable
PT-10 = polyurethane insulated magnet wire for clip or
bracket mounting
PT-20 = tinned copper 0.025 [0.635] sq. for printed circuit
mounting
Header: thermoset plastic
Covering: thermoplastic
STANDARD ELECTRICAL SPECIFICATIONS
DASH
NUMBER
TURNS
RATIO FIGURE
PRIMARY
IND. MIN.
(μH)
LEAKAGE
IND. MAX.
(μH)
INTERWINDING
CAPACITY MAX.
(pF)
DCR MAX.
()
UNIPOLAR
ET (V-μs)
101 (1) 1:1 ± 10 % 1/3 200 3 800 1.5-1.5 570
102 (1) 1:1 ± 10 % 1/3 500 6 1500 4.5-4.5 912
103 (1) 1:1 ± 10 % 1/3 1000 12 2000 8-8 1283
104 1:1 ± 10 % 1/3 2000 13 2800 12-12 1853
105 1:1 ± 10 % 1/3 5000 15 3500 18-18 2850
106 (1) 1:1:1 ± 10 % 2/4 200 3 800 2-2-2 570
107 1:1:1 ± 10 % 2/4 500 6 1500 6-6-6 912
108 1:1:1 ± 10 % 2/4 1000 12 2000 10-10-10 1283
109 1:1:1 ± 10 % 2/4 2000 (1) 13 2800 15-15-15 1853
110 1:1:1 ± 10 % 2/4 5000 15 3500 27-27-27 2850
111 (1) 2:1 ± 10 % 1/3 500 6 1000 4-2 912
112 (1) 2:1 ± 10 % 1/3 1000 10 1300 10-2 1288
113 2:1 ± 10 % 1/3 2000 12 1800 10-5 1881
114 2:1 ± 10 % 1/3 5000 15 2400 18-10 2850
115 (1) 2:1:1 ± 10 % 2/4 200 8 700 4-2-2 570
116 (1) 2:1:1 ± 10 % 2/4 500 11 1000 6-2-2 912
117 (1) 2:1:1 ± 10 % 2/4 1000 15 1300 5-2-2 1311
118 2:1:1 ± 10 % 2/4 2000 60 2000 10-5-5 1881
119 2:1:1 ± 10 % 2/4 5000 75 2100 20-10-10 2850
120 (1) 5:1 ± 10 % 1/3 5000 1500 400 19-3 2850
121 5:1:1 ± 10 % 2/4 5000 1500 400 20-4-4 2850
Models PT-10 and PT-20
www.vishay.com Vishay Dale
Not for New Designs
Revision: 08-Aug-16 2Document Number: 34073
For technical questions, contact: magnetics@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CIRCUIT DIAGRAMS
DIMENSIONS in inches (millimeters)
PART MARKING
- Vishay Dale
- Model
- Style
- Dash number
Line
Load
Transformer Coupled Unijunction Transistor Triggering Circuit Transformer Coupled Breakdown Diode Triggering Circuit
Line
Load
PT-10 PT-10
0.828 ± 0.062
[21.03 ± 1.57]
0.010 [0.254]
Dia., 4 Leads
0.593 ± 0.062
[15.06 ± 1.57]
Dia.
43
1.50 [38.10]
Min. Typ.
21
RED
GRN.
RED
GRN.
RED
1
GRN.
3
SEC.
4
GRN.
2
RED
PRI.
0.593 ± 0.062
[15.06 ± 1.57]
Dia. 0.828 ± 0.062
[21.03 ± 1.57]
0.010 [0.254]
Dia., 6 Leads
RED RED
GRN.
1.50 [38.10]
Min. Typ.
NAT.
GRN.
65
34
12
NAT.
PT-20
PT-20
3
1
24
SEC.PRI.
35
6
PRI. SEC. TER.
1
24
Figure 3 Figure 4
Figure 2Figure 1
13
0.500
[12.70]
0.250
[6.35]
Min.
0.250 [6.35]
Ref. 0.025 [0.635]Sq
6 Leads
65
24
0.300 [7.62]
Ref.
0.600 [15.24]
0.775 [19.68]
Max.
0.968 [24.59]
Max.
24
13
0.250
[6.35]
Min.
0.250 [6.35]
Ref. 0.025 [0.635]Sq.
4 Leads
0.300 [7.62]
Ref.
0.500
[12.70]
0.600 [15.24]
0.775 [19.68]
Max.
0.968 [24.59]
Max.
0.800 [20.32]
Max.
6
NAT.
NAT.
5
GRN.
3
RED
1
PRI. SEC. TER.
2
RED
4
GRN.
0.800 [20.32]
Max.
Models PT-10 and PT-20
www.vishay.com Vishay Dale
Not for New Designs
Revision: 08-Aug-16 3Document Number: 34073
For technical questions, contact: magnetics@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION
PT 10 101 EB e2
MODEL STYLE DASH NUMBER PACKAGE CODE JEDEC® LEAD (Pb)-FREE
STANDARD
GLOBAL PART NUMBER
PT 010 EB 101
MODEL STYLE PACKAGE
CODE DASH NUMBER
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
