Dupline(R) Field- and Installationbus Transmitter for Analog Voltage Signals Type FFD 1533 * * * * * * * * Ordering Key Product Description Dupline transmitters for external supply. For connection to signal converters with Transmitter with voltage input Voltage input signal: 1 x 0 to 10 VDC 8-bit (8 channels) resolution Binary transmission Enable input function D-housing Plug-in type module AC power supply standard voltage output (0 to 10 V). Converts analog voltage signals into binary codes. FFD 1533 024 Type: Dupline Input signal Supply Type Selection Supply Ordering no. 1 signal 0 to 10 VDC 24 VAC 120 VAC 220 VAC FFD 1533 024 FFD 1533 120 FFD 1533 220 Code module FMK A to FMK P Input/Output Specifications Signal input Signal range Zero adjustment (X1) Span adjustment (X2) Span Input resistance Resolution Settling time Open circuit monitoring Inaccuracy (ref. temp. 20C) of full scale Cable length Dielectric voltage Input - Dupline Transmission enable input Open loop voltage Short-circuit current Operating time for signal "1" Operating time for signal "0" Contact resistance Cable length Dielectric voltage Input - Dupline 1 voltage input 0 to 10 VDC None None None 100 k 8 bits (39.22 mV/LSB) 1 pulse train + 10 ms None Reference output Output voltage UR through pins 7 & 8 Output load resistance Short-circuit protection Output current Cable length Dielectric voltage Output - Dupline 1 voltage output 10 VDC (none regulated) 5 k none 2 mA 3m None 1% 3m 200 VAC (rms) 1 contact or NPN transistor 5 VDC 1 mA 1 pulse train + 10 ms 1 pulse train + 10 ms 100 3m 200 VAC (rms) Specifications are subject to change without notice (01.09.99) 1 FFD 1533 Power Specifications General Specifications Power supply Operational voltage through pins A1 & A2 220 120 024 Frequency Voltage interruption Rated operational power Rated operational withstand voltage 220 120 024 Dielectric voltage Supply - Dupline Supply - Signal input Supply - Enable input Supply - Reference output Power ON delay Environment Degree of protection Pollution degree Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Dimensions Material (see "Technical Information") Weight Approvals Overvoltage cat. III (IEC 60664) 230 VAC +6%, -15% (IEC 60038) 120 VAC 10% (IEC 60038) 24 VAC 10% 45 to 65 Hz 40 ms typ. 2.5 VA 4 kV 2.5 kV 800 V 2 kVAC (rms) 2 kVAC (rms) 2 kVAC (rms) 2 kVAC (rms) Undefined, 1 s IP 20 3 (IEC 60664) -20 to +50C (-4 to +122F) -50 to +85C (-58 to +185F) 20 to 80% 15 G (11 ms) 2 G (6 to 55 Hz) D-Housing 200 g UL Mode of Operation Transmitter with voltage signal input. The voltage signal is converted into a binary value represented as the binary status of an entire channel group (8 bit). This binary value may be reconverted into current or voltage signals through receivers with analogue outputs (type FAD 15..) or displayed as a scaled 7-segment display via D 6369 6475. A signal change of 0,392% of full scale influences the least significant bit, which is the highest channel of the selected group (J8 if FMK J is plugged in). A signal change of 49.8% of full scale influences the most significant bit or the lowest channel of the selected group (J1 in the above example). No value is transmitted unless the transmission enable Wiring Diagram input is activated (pins 5 and 7 connected). This input may also be used to transmit up to 255 individual values on one channel group by using Dupline receivers with demultiplex output type D 1230 5111. signal may represent physical parameters, e.g. shutter position, opening angle etc. Note: Analog transmitters must not be used in systems where channel generators with 2 or 3 sequences are installed. The 10 VDC reference output (pins 8 and 7) is a useful feature to supply for instance a potentiometer whose Operation Diagram Input Signal LSB = Least Significant Bit MSB = Most Significant Bit UR Input Common Transmission Enable Power Supply Channel status S: signal wire. Accessories Socket Socket cover Hold down spring Front mounting bezel DIN-rail for D 411 D 411 BB 5 HF FRS 2 FMD 411 For further information refer to "Accessories". 2 Specifications are subject to change without notice (01.09.99)