ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER GENERAL DESCRIPTION FEATURES The ICS8312 is a low skew, 1-to-12 LVCMOS / LVTTL Fanout Buffer and a member of the HiPerClockSTM HiPerClockSTMfamily of High Performance Clock Solutions from ICS. The ICS8312 single ended clock input accepts LVCMOS or LVTTL input levels. The low impedance LVCMOS outputs are designed to drive 50 series or parallel terminated transmission lines. The effective fanout can be increased from 12 to 24 by utilizing the ability of the outputs to drive two series terminated lines. * 12 LVCMOS / LVTTL outputs ICS * LVCMOS / LVTTL clock input * Maximum output frequency: 250MHz * Output skew: 150ps (maximum) * Operating supply modes: Core/Output 3.3V/3.3V, 2.5V/2.5V, 1.8V/1.8V, 3.3V/2.5V, 3.3V/1.8V, 2.5V/1.8V The ICS8312 is characterized at full 3.3V, 2.5V, and 1.8V, mixed 3.3V/2.5V, 3.3V/1.8V and 2.5V/1.8V output operating supply modes. Guaranteed output and part-to-part skew characteristics along with the 1.8V output capabilities makes the ICS8312 ideal for high performance, single ended applications that also require a limited output voltage. * 0C to 85C ambient operating temperature * Lead-Free package available * Industrial temperature information available upon request BLOCK DIAGRAM PIN ASSIGNMENT GND Q3 VDDO Q2 GND Q1 Q0 32 31 30 29 28 27 26 25 nD Q LE 12 CLK VDDO CLK_EN Q0:Q11 GND 1 24 VDD 2 23 VDDO CLK_EN 3 22 Q5 21 GND 20 Q6 Q4 CLK 4 GND 5 OE 6 19 VDDO VDD 7 18 Q7 GND 8 17 GND ICS8312 9 10 11 12 13 14 15 16 OE GND Q8 VDDO Q9 GND Q10 VDDO Q11 32-Lead LQFP 7mm x 7mm x 1.4mm body package Y Pacakge Top View 8312AY http://www.icst.com/products/hiperclocks.html 1 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER TABLE 1. PIN DESCRIPTIONS Number 1, 5, 8, 12, 16, 17, 21, 25, 29 2, 7 Name Type GND Power VDD Power 3 CLK_EN Input 4 CLK Input 6 OE Input Description Power supply ground. Core supply pins. Synchronous control for enabling and disabling clock outputs. Pullup LVCMOS / LVTTL interface levels. Pulldown Clock input. LVCMOS / LVTTL interface levels. Output enable. Controls enabling and disabling of outputs Pullup Q0 thru Q11. LVCMOS / LVTTL interface levels. 9, 11, 13, 15, Q11, Q10, Q9, Q8, 18, 20, 22, Q7, Q6, Q5, Output Q0 thru Q11 outputs. LVCMOS / LVTTL interface levels. 24, 26, 28, Q4, Q3, Q2, 30, 32 Q1, Q0 10, 14, 19, VDDO Power Output supply pins. 23, 27, 31 NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter Test Conditions Minimum Typical CIN Input Capacitance CPD Power Dissipation Capacitance (per output) RPULLUP Input Pullup Resistor 51 K RPULLDOWN Input Pulldown Resistor 51 K VDDO = 3.3V 5% 7 ROUT Output Impedance VDDO = 2.5V 5% 7 VDDO = 1.8V 0.2V 10 4 AND Units pF VDDO = 3.465V 19 pF VDDO = 2.625V 18 pF VDDO = 2V TABLE 3A. OUTPUT ENABLE Maximum 16 pF CLOCK ENABLE FUNCTION TABLE Control Inputs Output OE CLK_EN Q0:Q11 0 X Hi-Z 1 0 LOW 1 1 Follows CLK input TABLE 3B. CLOCK INPUT FUNCTION TABLE Inputs Outputs OE CLK_EN CLK Q0:Q11 1 1 0 LOW 1 1 1 HIGH 8312AY http://www.icst.com/products/hiperclocks.html 2 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER ABSOLUTE MAXIMUM RATINGS Supply Voltage, VDD 4.6V Inputs, VI -0.5V to VDD + 0.5 V Outputs, VO -0.5V to VDDO + 0.5V Package Thermal Impedance, JA 47.9C/W (0 lfpm) Storage Temperature, TSTG -65C to 150C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDO = 3.3V5%, TA = 0C TO 85C Symbol Parameter Minimum Typical Maximum Units VDD Core Supply Voltage Test Conditions 3.135 3.3 3.465 V 3.135 3.3 VDDO Output Supply Voltage 3.465 V IDD Power Supply Current 10 A IDDO Output Supply Current 10 A TABLE 4B. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDO = 2.5V5%, TA = 0C TO 85C Symbol Parameter VDD Test Conditions Minimum Typical Maximum Units Core Supply Voltage 2.375 2.5 2.625 V 2.375 2.5 VDDO Output Supply Voltage 2.625 V IDD Power Supply Current 10 A IDDO Output Supply Current 10 A TABLE 4C. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter VDD Test Conditions Minimum Typical Maximum Units Core Supply Voltage 1.6 1.8 2.0 V 1.6 1.8 VDDO Output Supply Voltage 2.0 V IDD Power Supply Current 10 A IDDO Output Supply Current 10 A TABLE 4D. POWER SUPPLY DC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 2.5V5%, TA = 0C TO 85C Symbol Parameter VDD Test Conditions Minimum Typical Maximum Units Core Supply Voltage 3.135 3.3 3.465 V 2.375 2.5 VDDO Output Supply Voltage 2.625 V IDD Power Supply Current 10 A IDDO Output Supply Current 10 A TABLE 4E. POWER SUPPLY DC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter Test Conditions Minimum Typical Maximum Units 3.135 3.3 3.465 V 1.6 1.8 2.0 V VDD Core Supply Voltage VDDO Output Supply Voltage IDD Power Supply Current 10 A IDDO Output Supply Current 10 A TABLE 4F. POWER SUPPLY DC CHARACTERISTICS, VDD = 2.5V5%, VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter Test Conditions Minimum Typical Maximum Units 2.375 2.5 2.625 V 1.6 1.8 2.0 V VDD Core Supply Voltage VDDO Output Supply Voltage IDD Power Supply Current 10 A IDDO Output Supply Current 10 A 8312AY http://www.icst.com/products/hiperclocks.html 3 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER TABLE 4F. LVCMOS DC CHARACTERISTICS, TA = 0C TO 85C Symbol Parameter CLK VIH Input High Voltage CLK_EN, OE CLK VIL Input Low Voltage CLK_EN, OE CLK IIH Input High Current CLK_EN, OE Test Conditions Minimum VDD = 3.3V 5% 2 IIL Input Low Current CLK_EN, OE VOH Output High Voltage Output Low Voltage Units VDD + 0.3 V VDD = 2.5V 5% 1.7 VDD + 0.3 V 0.65*VDD VDD + 0.3 V VDD = 3.3V 5% 2 VDD + 0.3 V VDD = 2.5V 5% 1.7 VDD + 0.3 V VDD = 1.8V 0.2V 0.65*VDD VDD + 0.3 V VDD = 3.3V 5% -0.3 1.3 V VDD = 2.5V 5% -0.3 0.7 V VDD = 1.8V 0.2V -0.3 0.35*VDD V VDD = 3.3V 5% -0.3 1.3 V VDD = 2.5V 5% -0.3 0.7 V VDD = 1.8V 0.2V -0.3 0.35*VDD V VDD = 3.3V 5% 150 A VDD = 2.5V 5% 150 A VDD = 1.8V 0.2V 150 A VDD = 3.3V 5% 5 A VDD = 2.5V 5% 5 A 5 A VDD = 3.3V 5% -5 A VDD = 2.5V 5% -5 A VDD = 1.8V 0.2V -5 A VDD = 3.3V 5% -150 A VDD = 2.5V 5% -150 A VDD = 1.8V 0.2V -150 A VDDO = 3.3V 5%; NOTE 1 2.6 V VDDO = 2.5V 5%; IOH = -1mA 2 V VDDO = 2.5V 5%; NOTE 1 1.8 V VDDO = 1.8V 0.2V; IOH = -100uA VDD - 0.2 V VDDO = 1.8V 0.2V; NOTE 1 VDD - 0.3 VDDO = 3.3V 5%; NOTE 1 VOL Maximum VDD = 1.8V 0.2V VDD = 1.8V 0.2V CLK Typical V 0.5 V VDDO = 2.5V 5%; IOL = 1mA 0.4 V VDDO = 2.5V 5%; NOTE 1 0.45 V VDDO = 1.8V 0.2V; IOL = 100uA 0.2 V VDDO = 1.8V 0.2V; NOTE 1 0.35 V NOTE 1: Outputs terminated with 50 to VDDO/2. See Parameter Measurement section, "Load Test Circuit" diagrams. 8312AY http://www.icst.com/products/hiperclocks.html 4 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER TABLE 5A. AC CHARACTERISTICS, VDD = VDDO = 3.3V5%, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 250 MHz 2.5 ns Output Skew; NOTE 2, 5 125 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 800 ps tR/tF Output Rise Time; NOTE 4 20% to 80% 200 700 ps odc Output Duty Cycle f 200MHz 45 55 % f 250MHz 1.2 1.9 All parameters measured at fMAX unless noted otherwise. See Table 5C listed below for Notes 1 through 5. TABLE 5B. AC CHARACTERISTICS, VDD = VDDO = 2.5V5%, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 250 MHz 3.2 ns Output Skew; NOTE 2, 5 150 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 1.1 ns tR/tF Output Rise Time; NOTE 4 20% to 80% 200 700 ps odc Output Duty Cycle f 150MHz 45 55 % f 250MHz 1.4 2.3 All parameters measured at fMAX unless noted otherwise. See Table 5C listed below for Notes 1 through TABLE 5C. AC CHARACTERISTICS, VDD = VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 200 MHz 4.8 ns Output Skew; NOTE 2, 5 140 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 2.3 ns tR/tF Output Rise Time; NOTE 4 20% to 80% 200 800 ps odc Output Duty Cycle f 100MHz 45 55 % f 200MHz 1.6 3.3 All parameters measured at fMAX unless noted otherwise. NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2. NOTE 3: Defined as the skew between outputs on different devices operating at the same supply voltages and with equal load conditions. Using the same type of inputs on each device, the outputs are measured at VDDO/2. NOTE 4: These parameters are guaranteed by characterization. Not tested in production. NOTE 5: This parameter is defined in accordance with JEDEC Standard 65. 8312AY http://www.icst.com/products/hiperclocks.html 5 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER TABLE 5D. AC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 2.5V5%, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 250 MHz 2.7 ns Output Skew; NOTE 2, 5 135 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 900 ps tR/tF Output Rise Time; NOTE 4 20% to 80% 200 700 ps odc Output Duty Cycle f 150MHz 45 55 % f 250MHz 1.4 2.1 All parameters measured at fMAX unless noted otherwise. See Table 5F listed below for Notes 1 through 5. TABLE 5E. AC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 200 MHz 3.4 ns Output Skew; NOTE 2, 5 145 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 1.3 ns tR/tF Output Rise Time; NOTE 4 20% to 80% 200 700 ps odc Output Duty Cycle f 100MHz 45 55 % f 200MHz 1.4 2.4 All parameters measured at fMAX unless noted otherwise. See Table 5F listed below for Notes 1 through TABLE 5F. AC CHARACTERISTICS, VDD = 2.5V5%, VDDO = 1.8V0.2V, TA = 0C TO 85C Symbol Parameter Test Conditions fMAX Output Frequency tpLH Propagation Delay Low to High; NOTE 1 tsk(o) Minimum Typical Maximum Units 200 MHz 3.7 ns Output Skew; NOTE 2, 5 150 ps tsk(pp) Par t-to-Par t Skew; NOTE 3, 5 1.5 ns tR/tF Output Rise Time; NOTE 4 20% to 80% 200 700 ps odc Output Duty Cycle f 100MHz 45 55 % f 200MHz 1.5 2.6 All parameters measured at fMAX unless noted otherwise. NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2. NOTE 3: Defined as the skew between outputs on different devices operating at the same supply voltages and with equal load conditions. Using the same type of inputs on each device, the outputs are measured at VDDO/2. NOTE 4: These parameters are guaranteed by characterization. Not tested in production. NOTE 5: This parameter is defined in accordance with JEDEC Standard 65. 8312AY http://www.icst.com/products/hiperclocks.html 6 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER PARAMETER MEASUREMENT INFORMATION 1.65V5% 1.25V5% SCOPE VDD, VDDO LVCMOS SCOPE VDD, VDDO Qx LVCMOS GND Qx GND -1.165V5% -1.25V5% 3.3V CORE/3.3V OUTPUT LOAD AC TEST CIRCUIT 2.5V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT 2.05V5% 0.9V 0.1V SCOPE VDD, VDDO 1.25V5% SCOPE VDD VDDO LVCMOS Qx LVCMOS Qx GND GND -0.9V 0.1V -1.25V5% 1.8V CORE/1.8V OUTPUT LOAD AC TEST CIRCUIT 3.3V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT 2.05V5% 0.9V0.1V 2.40.9V 0.9V0.1V SCOPE V DD VDDO LVCMOS VDDO Qx LVCMOS GND Qx GND -0.9V0.1V -0.9V0.1V 3.3V CORE/1.8V OUTPUT LOAD AC TEST CIRCUIT 8312AY SCOPE V DD 2.5 CORE/1.8V OUTPUT LOAD AC TEST CIRCUIT http://www.icst.com/products/hiperclocks.html 7 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER Part 1 V DDO Qx 2 DDO 2 Part 2 V DDO Qy V Qx V DDO Qy 2 t sk(o) OUTPUT SKEW 2 t sk(pp) PART-TO-PART SKEW VDD 2 80% 80% CLK Clock Outputs 20% 20% tR VDDO 2 tF Q0:Q11 t PD OUTPUT RISE/FALL TIME PROPAGATION DELAY V DDO 2 Q0:Q11 Pulse Width t odc = PERIOD t PW t PERIOD OUTPUT DUTY CYCLE/PLUSE WIDTH/PERIOD 8312AY http://www.icst.com/products/hiperclocks.html 8 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER RELIABILITY INFORMATION TABLE 6. JAVS. AIR FLOW TABLE FOR 32 LEAD LQFP JA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 67.8C/W 47.9C/W 55.9C/W 42.1C/W 50.1C/W 39.4C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS8312 is: 339 8312AY http://www.icst.com/products/hiperclocks.html 9 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. PACKAGE OUTLINE - Y SUFFIX LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER FOR 32 LEAD LQFP TABLE 7. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS BBA SYMBOL MINIMUM NOMINAL MAXIMUM 32 N A -- -- 1.60 A1 0.05 -- 0.15 A2 1.35 1.40 1.45 b 0.30 0.37 0.45 c 0.09 -- 0.20 D 9.00 BASIC D1 7.00 BASIC D2 5.60 Ref. E 9.00 BASIC E1 7.00 BASIC E2 5.60 Ref. 0.80 BASIC e L 0.45 0.60 0.75 0 -- 7 ccc -- -- 0.10 Reference Document: JEDEC Publication 95, MS-026 8312AY http://www.icst.com/products/hiperclocks.html 10 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER TABLE 8. ORDERING INFORMATION Part/Order Number Marking Package Count Temperature ICS8312AY ICS8312AY 32 Lead LQFP 250 per tray 0C to 85C ICS8312AYT ICS8312AY 32 Lead LQFP on Tape and Reel 1000 0C to 85C ICS8312AYLF ICS8312AYLF 32 Lead "Lead Free" LQFP 250 per tray 0C to 85C ICS8312AYLFT ICS8312AYLF 32 Lead "Lead Free" LQFP on Tape and Reel 1000 0C to 85C The aforementioned trademark, HiPerClockSTM is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 8312AY http://www.icst.com/products/hiperclocks.html 11 REV. C JUNE 14, 2004 ICS8312 Integrated Circuit Systems, Inc. LOW SKEW, 1-TO-12 LVCMOS / LVTTL FANOUT BUFFER REVISION HISTORY SHEET Rev Table T2 Page 2 B T4A - T4F 3 C C 8312AY Description of Change Pin Characteristics table - added categor y CPD. 1 Power Supply tables - changed IDD & IDDO max. current spec to 10A and removed typical value. Features section - corrected Output Skew typo error from 160ps to 150ps. T2 2 Pin Characteristics table - changed CIN 4pF max. to 4pF typical. T8 11 Added Lead Free Par t Number to Ordering Information table. http://www.icst.com/products/hiperclocks.html 12 Date 2/25/03 5/17/04 6/14/04 REV. C JUNE 14, 2004