TXB0102YZPR - Texas Instruments

YZP PACKAGE

(BOTTOM VIEW)

GND

VCCA

VCCB

VCCA

GND

DCT OR DCU PACKAGE

(TOP VIEW)

D1 D2

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

2-BIT BIDIRECTIONAL VOLTAGE-LEVEL TRANSLATOR

WITH AUTO DIRECTION SENSING AND ±15-kV ESD PROTECTION

Check for Samples: TXB0102

1FEATURES • Latch-Up Performance Exceeds 100 mA Per

JESD 78, Class II

2• Available in the Texas Instruments NanoFree™ • ESD Protection Exceeds JESD 22

Packages – A Port

• 1.2 V to 3.6 V on A Port and 1.65 V to 5.5 V on

B Port (VCCA ≤VCCB)– 2500-V Human-Body Model (A114-B)

• VCC Isolation Feature – If Either VCC Input Is at – 200-V Machine Model (A115-A)

GND, All Outputs Are in the High-Impedance – 1500-V Charged-Device Model (C101)

State – B Port

• OE Input Circuit Referenced to VCCA – 15-kV Human-Body Model (A114-B)

• Low Power Consumption, 4-μA Max ICC – 200-V Machine Model (A115-A)

• Ioff Supports Partial-Power-Down Mode – 1500-V Charged-Device Model (C101)

Operation

A. Pull up resistors are not required on both sides for Logic I/O.

B. If pull up or pull down resistors are needed, the resistor value must be over 50 kΩ.

C. 50 kΩis a safe recommended value, if the customer can accept higher Vol or lower Voh, smaller pull up or pull down

resistor is allowed, the draft estimation is Vol = Vccout × 4.5k/(4.5k + Rpu) and Voh = Vccout × Rdw/(4.5k + Rdw).

D. If pull up resistors are needed, please refer to the TXS0102 or contact TI.

E. For detailed information, please refer to application note SCEA043.

DESCRIPTION/ORDERING INFORMATION

This 2-bit non-inverting translator uses two separate configurable power-supply rails. The A port is designed to

track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB

accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation

between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. VCCA should not exceed VCCB.

When the output-enable (OE) input is low, all outputs are placed in the high-impedance state.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,

preventing damaging current backflow through the device when it is powered down.

To ensure the high-impedance state during power up or power down, OE should be tied to GND through a

pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.

NanoFree™ package technology is a major breakthrough in IC packaging concepts, using the die as the

package.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2NanoFree is a trademark of Texas Instruments.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Data

GNDGNDGND

Data A1 B1

VCCA VCCB

1.8-V

System

Controller

3.3-V

System

1.8 V 3.3 V

Data A2 DataB2

0.1 µF

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

ORDERING INFORMATION

TAPACKAGE(1) (2) ORDERABLE PART NUMBER TOP-SIDE MARKING(3)

NanoFree™ – WCSP (DSBGA)

0.23-mm Large Bump – YZP (Pb- Reel of 3000 TXB0102YZPR 2E_

free) Reel of 3000 TXB0102DCTR

–40°C to 85°C SOT (SOT-23) – DCT NFD_

Reel of 250 TXB0102DCTT

Reel of 3000 TXB0102DCUR

SOT (SOT-70) – DCU NFD_

Reel of 250 TXB0102DCUT

(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at

www.ti.com/sc/package.

(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the

TI website at www.ti.com.

(3) YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following

character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).

Table 1. PIN DESCRIPTION

PIN NAME FUNCTION

1 B2 Input/output B. Referenced to VCCB.

2 GND Ground

3 VCCA A port supply voltage. 1.2 V ≤VCCA ≤3.6 V and VCCA ≤VCCB

4 A2 Input/output A. Referenced to VCCA.

5 A1 Input/output A. Referenced to VCCA.

6 OE 3-State output. Pull OE low to place all outputs in 3-state mode. Referenced to VCCA.

7 VCCB B port supply voltage. 1.65 V ≤VCCB ≤5.5 V

8 B1 Input/output B. Referenced to VCCB.

Figure 1. TYPICAL OPERATING CIRCUIT

Product Folder Link(s): TXB0102

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

Absolute Maximum Ratings(1)

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

VCCA Supply voltage range –0.5 4.6 V

VCCB Supply voltage range –0.5 6.5

A port –0.5 4.6

VIInput voltage range(2) V

B port –0.5 6.5

A port –0.5 4.6

Voltage range applied to any output in the high-impedance or

VOV

power-off state(2) B port –0.5 6.5

A port –0.5 VCCA + 0.5

VOVoltage range applied to any output in the high or low state(2) (3) V

B port –0.5 VCCB + 0.5

IIK Input clamp current VI< 0 –50 mA

IOK Output clamp current VO< 0 –50 mA

IOContinuous output current ±50 mA

Continuous current through VCCA, VCCB, or GND ±100 mA

DCT package 220

θJA Package thermal impedance(4) DCU package 227 °C/W

YZP package 102

Tstg Storage temperature range –65 150 °C

(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating

conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.

(3) The value of VCCA and VCCB are provided in the recommended operating conditions table.

(4) The package thermal impedance is calculated in accordance with JESD 51-7.

Recommended Operating Conditions(1) (2)

VCCA VCCB MIN MAX UNIT

VCCA 1.2 3.6

Supply voltage V

VCCB 1.65 5.5

Data inputs 1.2 V to 3.6 V 1.65 V to 5.5 V VCCI × 0.65(3) VCCI

VIH High-level input voltage V

OE input 1.2 V to 3.6 V 1.65 V to 5.5 V VCCA × 0.65 5.5

Data inputs 1.2 V to 5.5 V 1.65 V to 5.5 V 0 VCCI × 0.35(3)

VIL Low-level input voltage V

OE input 1.2 V to 3.6 V 1.65 V to 5.5 V 0 VCCA × 0.35

Voltage range applied to any A port 0 3.6

VOoutput in the high-impedance 1.2 V to 3.6 V 1.65 V to 5.5 V V

B port 0 5.5

or power-off state A port inputs 1.2 V to 3.6 V 1.65 V to 5.5 V 40

Input transition rise or fall

Δt/Δv 1.65 V to 1.95 V 40 ns/V

rate B port inputs 1.2 V to 3.6 V 4.5 V to 5.5 V 30

TAOperating free-air temperature –40 85 °C

(1) The A and B sides of an unused data I/O pair must be held in the same state, i.e., both at VCCI or both at GND.

(2) VCCA must be less than or equal to VCCB and must not exceed 3.6 V.

(3) VCCI is the supply voltage associated with the input port.

Product Folder Link(s): TXB0102

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

Electrical Characteristics(1) (2)

over recommended operating free-air temperature range (unless otherwise noted) TA= 25°C –40°C to 85°C

TEST

PARAMETER VCCA VCCB UNIT

CONDITIONS MIN TYP MAX MIN MAX

1.2 V 1.1

VOHA IOH = –20 μA V

1.4 V to 3.6 V VCCA – 0.4

1.2 V 0.9

VOLA IOL = 20 μA V

1.4 V to 3.6 V 0.4

VOHB IOH = –20 μA 1.65 V to 5.5 V VCCB – 0.4 V

VOLB IOL = 20 μA 1.65 V to 5.5 V 0.4 V

IIOE VI= VCCI or GND 1.2 V to 3.6 V 1.65 V to 5.5 V ±1 ±2 μA

VIor VO= 0 to 3.6

A port 0 V 0 V to 5.5 V ±1 ±2

Ioff μA

VIor VO= 0 to 5.5

B port 0 V to 3.6 V 0 V ±1 ±2

IOZ A or B port OE = GND 1.2 V to 3.6 V 1.65 V to 5.5 V ±1 ±2 μA

1.2 V 1.65 V to 5.5 V 0.06

1.4 V to 3.6 V 1.65 V to 5.5 V 3

VI= VCCI or GND,

ICCA μA

IO= 0 3.6 V 0 V 2

0 V 5.5 V –2

1.2 V 1.65 V to 5.5 V 3.4

1.4 V to 3.6 V 1.65 V to 5.5 V 5

VI= VCCI or GND,

ICCB μA

IO= 0 3.6 V 0 V –2

0 V 5.5 V 2

1.2 V 1.65 V to 5.5 V 3.5

VI= VCCI or GND,

ICCA + ICCB μA

IO= 0 1.4 V to 3.6 V 1.65 V to 5.5 V 8

VI= VCCI or GND, 1.2 V 1.65 V to 5.5 V 0.05

ICCZA IO= 0, μA

1.4 V to 3.6 V 1.65 V to 5.5 V 3

OE = GND

VI= VCCI or GND, 1.2 V 1.65 V to 5.5 V 3.3

ICCZB IO= 0, μA

1.4 V to 3.6 V 1.65 V to 5.5 V 5

OE = GND

CiOE 1.2 V to 3.6 V 1.65 V to 5.5 V 2.5 3 pF

A port 5 6

Cio 1.2 V to 3.6 V 1.65 V to 5.5 V pF

B port 11 14

(1) VCCI is the supply voltage associated with the input port.

(2) VCCO is the supply voltage associated with the output port.

Timing Requirements

TA= 25°C, VCCA = 1.2 V VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V UNIT

TYP TYP TYP TYP

Data rate 20 20 20 20 Mbps

twPulse duration Data inputs 50 50 50 50 ns

Timing Requirements

over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (unless otherwise noted)

VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V UNIT

MIN MAX MIN MAX MIN MAX MIN MAX

Data rate 40 40 40 40 Mbps

twPulse duration Data inputs 25 25 25 25 ns

Product Folder Link(s): TXB0102

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

Timing Requirements

over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)

VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V UNIT

MIN MAX MIN MAX MIN MAX MIN MAX

Data rate 60 60 60 60 Mbps

twPulse duration Data inputs 17 17 17 17 ns

Timing Requirements

over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)

VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

± 0.2 V ± 0.3 V ± 0.5 V UNIT

MIN MAX MIN MAX MIN MAX

Data rate 100 100 100 Mbps

twPulse duration Data inputs 10 10 10 ns

Timing Requirements

over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)

VCCB = 3.3 V VCCB = 5 V

± 0.3 V ± 0.5 V UNIT

MIN MAX MIN MAX

Data rate 100 100 Mbps

twPulse duration Data inputs 10 10 ns

Switching Characteristics

TA= 25°C, VCCA = 1.2 V VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

FROM TO

PARAMETER UNIT

(INPUT) (OUTPUT) TYP TYP TYP TYP

A B 6.9 5.7 5.3 5.5

tpd ns

B A 7.4 6.4 6 5.8

A 1 1 1 1

ten OE μs

B 1 1 1 1

A 18 15 14 14

tdis OE ns

B 20 17 16 16

trA A port rise time 4.2 4.2 4.2 4.2 ns

tfA A port fall times 4.2 4.2 4.2 4.2 ns

trB B port rise times 2.1 1.5 1.2 1.1 ns

tfB B port fall times 2.1 1.5 1.2 1.1 ns

tsk(o) Channel-to-channel 0.5 0.5 0.5 1.4 ns

Max data rate 20 20 20 20 Mbps

Product Folder Link(s): TXB0102

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

Switching Characteristics

over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (unless otherwise noted)

VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

FROM TO ± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V

PARAMETER UNIT

(INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX

A B 1.4 12.9 1.2 10.1 1.1 10 0.8 9.9

tpd ns

B A 0.9 14.2 0.7 12 0.4 11.7 0.3 13.7

A 1111

ten OE μs

B 1111

A 5.9 31 5.7 25.9 5.6 23 5.7 22.4

tdis OE ns

B 5.4 30.3 4.9 22.8 4.8 20 4.9 19.5

trA A port rise times 1.4 5.1 1.4 5.1 1.4 5.1 1.4 5.1 ns

tfA A port fall times 1.4 5.1 1.4 5.1 1.4 5.1 1.4 5.1 ns

trB B port rise times 0.9 4.5 0.6 3.2 0.5 2.8 0.4 2.7 ns

tfB B port fall times 0.9 4.5 0.6 3.2 0.5 2.8 0.4 2.7 ns

tsk(o) Channel-to-channel 0.5 0.5 0.5 0.5 ns

Max data rate 40 40 40 40 Mbps

Switching Characteristics

over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)

VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

FROM TO ± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V

PARAMETER UNIT

(INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX

A B 1.6 11 1.4 7.7 1.3 6.8 1.2 6.5

tpd ns

B A 1.5 12 1.3 8.4 1 7.6 0.9 7.1

A 1111

ten OE μs

B 1111

A 5.9 31 5.1 21.3 5 19.3 5 17.4

tdis OE ns

B 5.4 30.3 4.4 20.8 4.2 17.9 4.3 16.3

trA A port rise times 1 4.2 1.1 4.1 1.1 4.1 1.1 4.1 ns

tfA A port fall times 1 4.2 1.1 4.1 1.1 4.1 1.1 4.1 ns

trB B port rise times 0.9 4.5 0.6 3.2 0.5 2.8 0.4 2.7 ns

tfB B port fall times 0.9 4.5 0.6 3.2 0.5 2.8 0.4 2.7 ns

tsk(o) Channel-to-channel 0.5 0.5 0.5 0.5 ns

Max data rate 60 60 60 60 Mbps

Product Folder Link(s): TXB0102

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

Switching Characteristics

over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)

VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V

FROM TO ± 0.2 V ± 0.3 V ± 0.5 V

PARAMETER UNIT

(INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX

A B 1.1 6.3 1 5.2 0.9 4.7

tpd ns

B A 1.2 6.6 1.1 5.1 0.9 4.4

A 1 1 1

ten OE μs

B 1 1 1

A 5.1 21.3 4.6 15.2 4.6 13.2

tdis OE ns

B 4.4 20.8 3.8 16 3.9 13.9

trA A port rise times 0.8 3 0.8 3 0.8 3 ns

tfA A port fall times 0.8 3 0.8 3 0.8 3 ns

trB B port rise times 0.7 3 0.5 2.8 0.4 2.7 ns

tfB B port fall times 0.7 3 0.5 2.8 0.4 2.7 ns

tsk(o) Channel-to-channel 0.5 0.5 0.5 ns

Max data rate 100 100 100 Mbps

Switching Characteristics

over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)

VCCB = 3.3 V VCCB = 5 V

FROM TO ± 0.3 V ± 0.5 V

PARAMETER UNIT

(INPUT) (OUTPUT) MIN MAX MIN MAX

A B 0.9 4.7 0.8 4

tpd ns

B A 1 4.9 0.9 4.5

A 1 1

ten OE μs

B 1 1

A 4.6 15.2 4.3 12.1

tdis OE ns

B 3.8 16 3.4 13.2

trA A port rise times 0.7 2.5 0.7 2.5 ns

tfA A port fall times 0.7 2.5 0.7 2.5 ns

trB B port rise times 0.5 2.3 0.4 2.7 ns

tfB B port fall times 0.5 2.3 0.4 2.7 ns

tsk(o) Channel-to-channel 0.5 0.5 ns

Max data rate 100 100 Mbps

Product Folder Link(s): TXB0102

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

Operating Characteristics

TA= 25°C VCCA

1.2 V 1.2 V 1.5 V 1.8 V 2.5 V 2.5 V 3.3 V

VCCB

PARAMETER TEST CONDITIONS UNIT

3.3 V

5 V 1.8 V 1.8 V 1.8 V 2.5 V 5 V to

5 V

TYP TYP TYP TYP TYP TYP TYP

A port input, B port output 7.8 8 8 7 7 8 8

CL= 0, f = 10 MHz,

CpdA B port input, A port output 12 11 11 11 11 11 11

tr= tf= 1 ns, pF

OE = VCCA

A port input, B port output 38.1 29 29 29 29 30 30

CpdB (outputs enabled)

B port input, A port output 25.4 19 18 18 18 21 21

A port input, B port output 0.01 0.01 0.01 0.01 0.01 0.01 0.01

CL= 0, f = 10 MHz,

CpdA B port input, A port output 0.01 0.01 0.01 0.01 0.01 0.01 0.01

tr= tf= 1 ns, pF

OE = GND

A port input, B port output 0.01 0.01 0.01 0.01 0.01 0.01 0.02

CpdB (outputs disabled)

B port input, A port output 0.01 0.01 0.01 0.01 0.01 0.02 0.03

Product Folder Link(s): TXB0102

A B

VCCA VCCB

One

Shot

One

Shot

One

Shot

One

Shot

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

PRINCIPLES OF OPERATION

Applications

The TXB0102 can be used in level-translation applications for interfacing devices or systems operating at

different interface voltages with one another.

Architecture

The TXB0102 architecture (see Figure 2) does not require a direction-control signal to control the direction of

data flow from A to B or from B to A. In a dc state, the output drivers of the TXB0101 can maintain a high or low,

but are designed to be weak, so that they can be overdriven by an external driver when data on the bus starts

flowing the opposite direction.

The output one shots detect rising or falling edges on the A or B ports. During a rising edge, the one shot turns

on the PMOS transistors (T1, T3) for a short duration, which speeds up the low-to-high transition. Similarly,

during a falling edge, the one shot turns on the NMOS transistors (T2, T4) for a short duration, which speeds up

the high-to-low transition. The typical output impedance during output transition is 70 Ωat VCCO = 1.2 V to 1.8 V,

50 Ωat VCCO = 1.8 V to 3.3 V, and 40 Ωat VCCO = 3.3 V to 5 V.

Figure 2. Architecture of TXB0102 I/O Cell

Input Driver Requirements

Typical IIN vs VIN characteristics of the TXB0102 are shown in Figure 3. For proper operation, the device driving

the data I/Os of the TXB0102 must have drive strength of at least ±2 mA.

Product Folder Link(s): TXB0102

A. V istheinputthresholdvoltageoftheTXB0102(typically /2.

V isthesupplyvoltageoftheexternaldriver.

CCI

–(V – V )/4k

D T Ω

V /4k

TΩ

VIN

IIN

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

Figure 3. Typical IIN vs VIN Curve

Power Up

During operation, ensure that VCCA ≤VCCB at all times. During power-up sequencing, VCCA ≥VCCB does not

damage the device, so any power supply can be ramped up first. The TXB0102 has circuitry that disables all

output ports when either VCC is switched off (VCCA/B = 0 V).

Enable and Disable

The TXB0102 has an OE input that is used to disable the device by setting OE = low, which places all I/Os in the

high-impedance (Hi-Z) state. The disable time (tdis) indicates the delay between when OE goes low and when the

outputs are disabled (Hi-Z). The enable time (ten) indicates the amount of time the user must allow for the one-

shot circuitry to become operational after OE is taken high.

Pullup or Pulldown Resistors on I/O Lines

The TXB0102 is designed to drive capacitive loads of up to 70 pF. The output drivers of the TXB0102 have low

dc drive strength. If pullup or pulldown resistors are connected externally to the data I/Os, their values must be

kept higher than 50 kΩto ensure that they do not contend with the output drivers of the TXB0102.

For the same reason, the TXB0102 should not be used in applications such as I2C or 1-Wire where an open-

drain driver is connected on the bidirectional data I/O. For these applications, use a device from the TI TXS01xx

series of level translators.

Product Folder Link(s): TXB0102

From Output

Under Test

LOAD CIRCUIT FOR

ENABLE/DISABLE

TIME MEASUREMENT

2 × VCCO

Open

50 kW

VCCI

0 V

VCCI/2 VCCI/2

VOLTAGE WAVEFORMS

PROPAGATION DELAY TIMES VOLTAGE WAVEFORMS

PULSE DURATION

Input

tPZL/tPLZ

tPHZ/tPZH

2 × VCCO

Open

TEST S1

A. CL includes probe and jig capacitance.

B. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns.

C. The outputs are measured one at a time, with one transition per measurement.

D. tPLH and tPHL are the same as tpd.

E. VCCI is the VCC associated with the input port.

F. VCCO is the VCC associated with the output port.

G. All parameters and waveforms are not applicable to all devices.

50 kW

From Output

Under Test

1 MW

15 pF 15 pF

LOAD CIRCUIT FOR MAX DATA RATE,

PULSE DURATION PROPAGATION

DELAY OUTPUT RISE AND FALL TIME

MEASUREMENT

tPLH tPHL

0 V

VCCO/2

VCCI/2 VCCI/2

0.9 y VCCO

VCCO/2

0.1 y VCCO tf

VCCI

Input

Output VOH

VOL

TXB0102

www.ti.com

SCES641B –MAY 2007–REVISED MAY 2012

PARAMETER MEASUREMENT INFORMATION

Figure 4. Load Circuits and Voltage Waveforms

Product Folder Link(s): TXB0102

TXB0102

SCES641B –MAY 2007–REVISED MAY 2012

www.ti.com

REVISION HISTORY

Changes from Original (May 2007) to Revision A Page

• Added ball labels to the YZP Package. ................................................................................................................................ 1

Changes from Revision A (January 2011) to Revision B Page

• Added notes to pin out graphics. .......................................................................................................................................... 1

Product Folder Link(s): TXB0102

D: Max = 1.918 mm, Min = 1.858 mm

E: Max = 0.918 mm, Min = 0.858 mm

PACKAGE OPTION ADDENDUM

www.ti.com 7-May-2012

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status (1) Package Type Package

Drawing Pins Package Qty Eco Plan (2) Lead/

Ball Finish MSL Peak Temp (3) Samples

(Requires Login)

TXB0102DCUR ACTIVE US8 DCU 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

TXB0102DCURG4 ACTIVE US8 DCU 8 3000 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

TXB0102DCUT ACTIVE US8 DCU 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

TXB0102DCUTG4 ACTIVE US8 DCU 8 250 Green (RoHS

& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

TXB0102YZPR ACTIVE DSBGA YZP 8 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 7-May-2012

Addendum-Page 2

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

TXB0102DCUR US8 DCU 8 3000 180.0 8.4 2.25 3.35 1.05 4.0 8.0 Q3

TXB0102YZPR DSBGA YZP 8 3000 178.0 9.2 1.02 2.02 0.63 4.0 8.0 Q1

TXB0102YZPR DSBGA YZP 8 3000 180.0 8.4 1.02 2.02 0.63 4.0 8.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 7-May-2012

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

TXB0102DCUR US8 DCU 8 3000 202.0 201.0 28.0

TXB0102YZPR DSBGA YZP 8 3000 220.0 220.0 35.0

TXB0102YZPR DSBGA YZP 8 3000 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 7-May-2012

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265