19-1393; Rev 0; 10/98 General Description The MAX4604/MAX4605/MAX4606 quad analog switch- es feature 5Q max on-resistance. On-resistance is matched between switches to 0.50 max and is flat (0.5 max) over the specified signal range. Each switch can handle Rail-to-Rail analog signals. The off-leakage cur- rent is only 2.5nA max at +85C. These analog switches are ideal in low-distortion applications and are the pre- ferred solution over mechanical relays in automatic test equipment or in applications where current switching is required. These switches have low power requirements, require less board space, and are more reliable than mechanical relays. The MAX4604 has four normally closed (NC) switches, the MAX4605 has four normally open (NO) switches, and the MAX4606 has two NC and two NO switches. These switches operate from a single supply of +4.5V to +36V or from dual supplies of +4.5V to +20V. All dig- ital inputs have +0.8V and +2.4V logic thresholds, ensuring TTL/CMOS logic compatibility when using +15V supplies or a single +12V supply. Applications PBX, PABX Systems Audio-Signal Routing Reed Relay Replacement Test Equipment Communication Systems Avionics MAAS 5Q, Quad, SPST, CMOS Analog Switches Features @ Low On-Resistance (5Q max) Guaranteed Ron Match Between Channels (0.5Q max) # Guaranteed Ron Flatness over Specified Signal Range (0.50 max) # Rail-to-Rail Signal Handling # Guaranteed ESD Protection > 2000V per Method 3015.7 # Single-Supply Operation: +4.5V to +36V Dual-Supply Operation: +4.5V to 20V # TTL/CMOS-Compatible Control Inputs Ordering Information PART TEMP. RANGE PIN-PACKAGE MAX4604CAE 0C to +70C 16 SSOP MAX4604CSE 0C to +70C 16 Narrow SO MAX4604CPE 0C to +70C 16 Plastic DIP MAX4604EAE -40C to +85C 16 SSOP MAX4604ESE -40C to +85C 16 Narrow SO MAX4604EPE -40C to +85C 16 Plastic DIP Ordering Information continued at end of data sheet. Pin Configurations/Functional Diagrams/Truth Tables TOP VIEW VJ ni [1 He] ine plo Aol NCt qo er Nc2 nor [3 | IN GH>, ~ <Ha IN2 COM ef -o~% aoa] come Ha] Noe YD pax [el ono [5] = Max4e04 fra] vy eno [5] nos [6 | pax [3] v MAX4605 Ha] we Ht] Nos nea [6 | H+ | Nes coma Toe 'y-o-fi] coma IN4 [e} >! <H 3] ins SSOP/SO/DIP com4 Ghay ee coms IN4 [e}}> <H2] 13 SSOP/SO/DIP MAX4604 MAX4605 LOGIC SWITCH LOGIC SWITCH 0 ON 0 OFF 1 OFF 1 ON SWITCHES SHOWN FOR LOGIC 0 INPUT COM plo 15 | come nor [3 | = Ne2 coma [7] QO nm LH: <He] IN? v 4) wax MAX4606 eno [5 | 13] v4 f2] vw na [8 now [6 | H+] Neo Hoy Lota cOM3 HD KH 9 | ins SSOP/SO/DIP MAX4606 LOGIC SWITCHES SWITCHES 1,4 2,3 0 OFF 1 ON ON OFF Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. MAXIM Maxim Integrated Products 1 For free samples & the latest literature: http://)www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769. GO9VXVW/SO9VXVW/PO9OVXVWNMAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches ABSOLUTE MAXIMUM RATINGS V+ to GND one enaneeeeeaceeneneel V- to GND.. All Other Pins to DGND (Note 1) ... -0.3V to +44V +0.3V to -44V -0.3V to +44V (DGND - 0.3V) to (V+ + 0.3V) (V- - 0.3V) to (V+ + 0.3V) Continuous Current (COM_, NO_, NC_) wee +100mA Peak Current (COM_, NO_, NC_) (pulsed at ims, 10% duty cycle)... eens +300mA Continuous Power Dissipation (Ta = +70C) 16-pin SSOP (derate 7.1MW/C above + 70C) ue 571mW 16-pin Narrow SO (derate 8.70mW/C above +70C) ....696mW 16-pin Plastic DIP (derate 10.53mW/C above +70C) ..842mW Operating Temperature Ranges MAX460_C_ EE ooo eesceeeenceeneeeeenee 0C to +70C MAX460_E_ Eo. cceeeecce ene eseesereeeneees -40C to +85C Storage Temperature Range 65C to +160C Lead Temperature (soldering, 10SC) uo... cece sees +300C Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- are clamped by internal diodes. Limit forward-diode current to maximum current rating. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICSDual Supplies (V+ = +15V, V- = -15V, VL = 5V, VIN_H= 2.4V, VIN _L = 0.8V, TA = TIN to TMAX, unless otherwise noted. Typical values are at Ta = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS (Note 2) ANALOG SWITCH Input Voltage Range Vcom_, VNO_.; - (Note 3) VNC_ V V+ V COM_to NO_or NC_ Ron Icom. = 10mA, Ta= +25C 8 4 On-Resistance VNo_orVNc = 2+10V Ta = Twin to Tuax 5 COM_to NO_ or NC_ Ta = +25C 0.2 0.5 On-Resistance Match Between ARON ICOM ey VNO_ Q Channels (Note 4) No_= = TA = TMIN to TMAX 0.7 COM_to NO_ or NC_ _ . Ta = +25C 0.2 0.5 On-Resistance Flatness RFLAT(ON) ICOM. = tom NNO Q (Note 5) NO_= 96 Ta = TMIN to TMAX 0.6 Off-Leakage Current Ino . Inc Vcom_ = +10V, Ta = +25C 0.5 0.01 0.5 nA (NO_ or NC_) (Note 6) 7 | VNo_or VNC_= +10V |T, = Twin to Tuax -2.5 25 COM Off-Leakage Current ICOM (OE Vcom_ = +10V, Ta = +25C 0.5 0.01 0.5 nA (Note 6) (OFF) VNoO_or VNC_= 10V |T, = Twin to Tuax -25 25 COM On-Leakage Current Voom SON ov Ta = +25C 4 0.02 1 A (Note 6) COM(ON) | VNO_or VNc_= + n or floating Ta = TMIN to Tmax 5 5 LOGIC INPUT Hoh Current with Input Voltage INH IN_ = 2.4V, all others = 0.8V 0.500 0.001 0.500| pA put Current with Input Voltage INL IN_ = 0.8V, all others = 2.4V 0.500 0.001 0.500] pA Logic Input High Voltage VIN_H 2.4 1.7 Vv Logic Input Low Voltage VINLL 1.7 0.8 Vv 2 MAXIMA5Q, Quad, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICSDual Supplies (continued) (V+ = +15V, V- = -15V, VL = 5V, VIN _H= 2.4V, ViIN_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are TA = +25C.) PARAMETER | SYMBOL | CONDITIONS | MIN TYP MAX | UNITS POWER SUPPLY Power-Supply Range +4.5 +20.0 Vv Ta = +25C -0.5 0.001 0.5 Positive Supply Current I+ All channels on or off, | (A = + pA Vin = Oor 5V Ta = TMIN to Tmax 5 5 Ta = +25C -0.5 0.001 0.5 Negative Supply Current - i channels on or off, | TA = + pA IN=Oor 5V Ta = TMIN to Tmax 5 5 . All channels on or off, |TA = +25C 0.5 0.001 0.5 Logic Supply Current IL pA Vin = Oor 5V Ta = TMIN to Tmax 5 5 All channels on or off, |TA = +25C -0.5 0.001 0.5 Ground Current IGND pA VIN = Oor 5V Ta = TMIN to Tmax 5 5 SWITCH DYNAMIC CHARACTERISTICS GO9VXVW/SO9VXVW/PO9OVXVWN Figure 2, _ Turn-On Time ton Voom. = +10V TA = +25C 120 ns Figure 2, _ Turn-Off Time toFF Voom. = 10V Ta = +25C 130 ns . o. CL = 1.0nF, VGEN = 0, Charge Injection Q RGEN = 0, Figure 3, Ta = +25C 225 pc Off-Isolation (Note 7) Viso Roure 4. Tro wooo. = 1MHz, -62 dB Crosstalk (Note 8) Vot Roure 8 Tre wooo. = 1MHz, -60 dB NC or NO Capacitance C(OFF) f = 1MHz, Figure 6, Ta = +25C 34 pF COM Off-Capacitance Ccom) f = 1MHz, Figure 6, Ta = +25C 34 pF On-Capacitance Ccom) f = 1MHz, Figure 7, Ta = +25C 150 pF MAXLM 3MAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICSSingle Supply (V+ = +12V, V- = 0, VL = 5V, VIN H= 2.4V, VIN _L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at Ta = +25C.) PARAMETER SYMBOL CONDITIONS MIN ote 2) MAX UNITS ANALOG SWITCH Input Voltage Range Vcom. VNo, (Note 3) Ve. GND V+ V COM_to NO_or NC_ R Icom. = 10mA, Ta = +25C 5.5 8 ; On-Resistance ON VNo or VNC = 10V Ta = TMIN to TMAX 10 COM_to NO_ or NC_ | = 10mA. V; Ta = +25C 0.05 0.5 On-Resistance Match Between ARON Wo = 10V_ NO_ Q Channels (Note 4) NC_= TA = TMIN to TMAX 0.7 COM_to NO_orNC_ Icom = 10mA; VNo Ta = +25C 0.25 0.6 On-Resistance Flatness RFLAT(ON) or Ve = 3V 6V OV Q (Note 5) NC_= N,N Ta = TMIN to Tmax 0.8 Off-Leakage Current wo .Iwe Woe vie 1 ys y Ta = +25C 05 0.01 05 A (NO_ or NC_) (Notes 6, 9) TO ay - Ta =Twinto Tmax | -2.5 25 COM_ Off-Leakage Current Vcom_ = 1V, 10V; Ta = +25C 0.5 0.01 0.5 nA (Notes 6, 9) COM_{(OFF) Vno_or Vnc_=10V_ | Tp, = Tryin to TMax -2.5 2.5 COM_On-Leakage Current yCOM- Ah V, aot TA= +25C 1 0.02 1 A (Notes 6 9) COM_(ON) NO_or NC_= , n ' 10V or floating Ta = TmIN to Tmax 5 5 LOGIC INPUT Hoh Current with Input Voltage INH IN_ = 2.4V, all others = 0.8V 0.500 0.001 0.500] pA Input Current with Input Voltage INL IN_ = 0.8V, all others = 2.4V 0.500 0.001 0.500| pA Low Logic Input High Voltage VIN_H 2.4 1.7 Vv Logic Input Low Voltage VIN_L 1.7 0.8 Vv POWER SUPPLY Power-Supply Range 45 36.0 Vv Ta = +25C -0.5 0.001 0.5 Positive Supply Current I+ 7 ohannes on or off, pA IN= Ta = TMIN to TMAx 5 5 Ta = +25C -0.5 0.001 0.5 Logic Supply Current IL 7 ohannes on or off, pA IN= Ta = TMIN to TMAx 5 5 Ta = +25C -0.5 0.001 0.5 Ground Current IGND Vin=Oor5V pA Ta = TMIN to TMAx 5 5 MAK5Q, Quad, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICSSingle Supply (continued) (V+ = +12V, V- = 0, VL = 5V, VIN_H = 2.4V, ViIN_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) MIN TYP MAX PARAMETER SYMBOL CONDITIONS UNITS (Note 2) SWITCH DYNAMIC CHARACTERISTICS Figure 2, Turn-On Time ton Voom_ = 10V, Ta = +25C 160 220 ns V+ =12V Figure 2, Turn-Off Time toFF Voom_ = 10V, Ta = +25C 120 160 ns V+ =12V CL = 1.0nF, VGeEN = 0, Charge Injection Q RoGen = 0, Figure 3, 10 pc V+ = 12V, V- = 0, Ta = +25C Ri = 50, CL = 5pF, Crosstalk (Note 8) Vet f= 1MHz, Figure 5, Ta = +25C -60 dB NC_or NO_ Capacitance C(OFF) f = 1MHz, Figure 6, Ta = +25C 52 pF COM_Off-Capacitance Ccom) f = 1MHz, Figure 6, Ta = +25C 52 pF On-Capacitance Ccom) f = 1MHz, Figure 7, Ta = +25C 100 pF GO9VXVW/SO9VXVW/PO9OVXVWN Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: ARon = RON(MAX) - RON(MIN). Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range. Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25C. Note 7: Off-isolation = 20log10 [Vcom_/ (VNc_ or VNO_)], VCOM_ = output, VNc_ or VNO_ = input to off switch. Note 8: Between any two switches. Note 9: Leakage testing at single supply is guaranteed by testing with dual supplies. MAXLM 5MAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches (Ta = +25C, unless otherwise noted.) ON- RESISTANCE vs. Voom (DUAL SUPPLIES) =10mA 3 Z +, V- =+5.0V Sg & V4, V- = +15.0V V+, V- = 420.0V -20 -15 -10 -5 0 5 10 15 20 Vcow (V) ON- RESISTANCE vs. Vcov AND TEMPERATURE (SINGLE SUPPLY) 8.0 xs V4=120V 2 7 Ta=105C7 YS 7.0 = 6.5 60 a & 5.5 5.0 45 4.0 3.5 3.0 12 Vcow (V) TURN- ON/TURN- OFF TIME vs. Vcom R =1000 E C= 35pF 3 5 5 10 Vcow (V) 6 ON-RESISTANCE vs. Vcom AND TEMPERATURE (DUAL SUPPLIES) Icom = 10mA MAX4604 roc? a Vcow (V) ON/OFF- LEAKAGE CURRENT vs. TEMPERATURE 100k V+=+15V 10k FF V- =-15V MAX4604 toc05 LEAKAGE (pA) 3 0.1 0.01 -40 -25 -10 5 20 35 50 65 80 95100 TEMPERATURE (C) TURN- ON/TURN- OFF TIME vs. SUPPLY VOLTAGE torr AMX4604 toc08- ton, tore (ns) Voom = 10V R_ = 1000 C.= 35pF 10 11 12 13 14 15 16 17 18 19 20 V+, V- (V) ton, torr (ns) Typical Operating Characteristics ON- RESISTANCE vs. Voom (SINGLE SUPPLY) =10mA MAX4604 toc03 V+ =12.0V 6 V+ =24.0V 0 3 6 9 12 15 18 21 24 Voom (V) CHARGE INJECTION vs. Voom NMAX4604 toc06 V+, V- = 15V Voom (V) TURN: ON/TURN- OFF TIME vs. TEMPERATURE 170 2 150 P-L =35pF = 140 430 420 110 100 90 80 40 -20 0 2 40 60 80 100 TEMPERATURE (C) MAAXLM5Q, Quad, SPST, CMOS Analog Switches (TA = +25C, unless otherwise noted.) SUPPLY CURRENT vs. TEMPERATURE 100k I+, F (nA) 04 0.01 MAX4604 toc10. -40 -25 -10 5 20 35 50 65 80 95100 TEMPERATURE (C) Typical Operating Characteristics (continued) FREQUENCY RESPONSE MAX4604 toc 14 180 90 ON-RESPONSE -20 0 -30 0 40 -180 #2 z= on -50 -270 2 8 Ww = -60 -360 2 x -70 - ISOLATION -450 -540 -630 -720 0.1 1 10 100 FREQUENCY (MHz) -80 -90 -100 Pin Description PIN NAME FUNCTION MAX4604 | MAX4605 | MAX4606 IN1, IN2, . a 1,16,9,8 1,16, 9,8 1,16,9,8 IN3, IN4 Logic-Control Digital Inputs 2, 15, 2, 15, 2, 15, COM1, COM2, . . 10,7 10,7 10,7 COM3, COM4 Analog Switch, Common Terminals NC1, NC2, . . 3,14, 11,6 - - NC3, NC4 Analog Switch, Normally Closed Terminals NO1, NO2, . . - 3,14, 11,6 - NO3, NO4 Analog Switch, Normally Open Terminals - - 3,6 NO1, NO4 Analog Switch, Normally Open Terminal - - 14,11 NC2, NC3 Analog Switch, Normally Closed Terminal 4 4 4 V- Negative Analog Supply-Voltage Input. Connect to GND for single- supply operation. 5 5 5 GND Ground 12 12 12 VL Logic-Supply Input 13 13 13 V+ Positive Analog Supply Input MAXLM GO9VXVW/SO9VXVW/PO9OVXVWNMAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches Applications Information Overvoltage Protection Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maxi- mum ratings, because stresses beyond the listed rat ings can cause permanent damage to the devices. Always sequence V+ on first, then V-, followed by the logic inputs, NO, or COM. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) in series with supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog signal range to one diode drop below V+ and one diode drop above V-, but does not affect the devices low switch resistance and low leakage characteristics. Device operation is unchanged, and the difference between V+ and V- should not exceed 44V. These protection diodes are not recommended when using a single supply. Off-lsolation at High Frequencies In 50Q systems, the high-frequency on-response of these parts extends from DC to above 100MHz with a typical loss of -2dB. When the switch is turned off, how- ever, it behaves like a capacitor, and off isolation decreases with increasing frequency. (Above 300MHz, the switch actually passes more signal turned off than turned on.) This effect is more pronounced with higher source and load impedances. Above 5MHz, circuit board layout becomes critical, and it becomes difficult to characterize the response of the switch independent of the circuit. The graphs shown in the Typical Operating Characteristics were taken using a 50Q source and load connected with BNC connec- tors to a circuit board deemed average; that is, designed with isolation in mind, but not using strip-line or other special RF circuit techniques. For critical appli- cations above 5MHz, use the MAX440, MAX441, and MAX442, which are fully characterized up to 160MHz. +15V D1 MAXIM Ve MAX4604 MAX4605 MAX4606 COM_ J i NO_ V- D2 -15V * INTERNAL PROTECTION DIODES Figure 1. Overvoltage Protection Using External Blocking Diodes tr < 20ns Loaic tf < 20ns INPUT SWITCH 9 OUTPUT LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE LOGIC SENSE MAAKLM MAx4604 MAX4605 48V +15V MAX4606 | | SWITCH VL V+ SWITCH Yooyy | COM_ 7 NO oe INPUT - i ORNG_ ! RL CL 1002] 35pF p. [EMT GND . = = Loaic u INPUT ; ty REPEAT TEST FOR EACH SWITCH. FOR LOAD CONDITIONS, SEE Electrical Characteristics. Gy INCLUDES FIXTURE AND STRAY CAPACITANCE BL Vo=Voow (a Agi) Figure 2. Switching-Time Test Circuit 8 MAK5Q, Quad, SPST, CMOS Analog Switches MAXIM MAX4604 5V 15V + + MAX4605 l | AVo MAX4606 VL V+ RGeN No COM_ oa NC_OR Vo ! NO_ Tt VIN \ C, OFF on OFF Gy __ GND a V- | ON = OFF OFF t | Vi - = 18V " Q= (AVo)(C1) Vin =43V Viv DEPENDS ON SWITCH CONFIGURATION; = INPUT POLARITY DETERMINED BY SENSE OF SWITCH, Figure 3. Charge-Injection Test Circuit MAX MAXUM MAX4604 MAX4604 oH +5V MAXA605 ov ey MAX4605 | MAX4606 dl [-? | MAX4606 SIGNAL = SIGNAL = V+ Ww 500 GENERATOR 0dBm a Ve ML GENERATOR OB CoM ao @ xy : = INt t IN2 = = = Qt = Oor24v Dor24v ere Hye Oor2.4V ANALYZER COM_ Ivo ORNO. = ANALYZER e-{nez aS" t vo. GND v vt GND Ve 6 Cc RL = > TD eh Loop Th = = -15V = = -15V = = Figure 4. Off-lsolation Test Circuit MAXLM Figure 5. Crosstalk Test Circuit GO9VXVW/SO9VXVW/PO9OVXVWNMAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches +15V Hf MAXIM +5V CAPACITANCE METER f= 1MHz NC_ORNO. [ot Cc I -15 MAX4604 MAX4605 MAX4606 Oor 2.4V 1 CAPACITANCE METER f= 1MHz MAXIM +15V +BY MAX4604 c MAX4605 co H MAX4606 = V4 VL COM_ a <4 | Oo 2.4V = NC_ ORNO GND V- Cc Figure 6. Switch Off-Capacitance Test Circuit 10 Figure 7. Switch On-Capacitance Test Circuit MAK5Q, Quad, SPST, CMOS Analog Switches __Ordering Information (continued) TRANSISTOR COUNT: 100 Chip Information NOTES: 1. D&E DO NOT INCLUDE MOLD FLASH. 2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED 115mm .006%) 3. CONTROLLING DIMENSION: MILLIMETER Tu fH Al PART TEMP. RANGE PIN-PACKAGE MAX4605CAE 0C to +70C 16 SSOP MAX4605CSE 0C to +70C 16 Narrow SO MAX4605C PE 0C to +70C 16 Plastic DIP MAX4605EAE -40C to +85C 16 SSOP MAX4605ESE -40C to +85C 16 Narrow SO MAX4605EPE -40C to +85C 16 Plastic DIP MAX4606CAE 0C to +70C 16 SSOP MAX4606CSE 0C to +70C 16 Narrow SO MAX4606C PE 0C to +70C 16 Plastic DIP MAX4606EAE -40C to +85C 16 SSOP MAX4606ESE -40C to +85C 16 Narrow SO MAX4606EPE -40C to +85C 16 Plastic DIP Package Information oa caps a INCHES _|MILLIMETERS a A | 0.068 {0.078 | 1.73 | 1.99 MIN MAX MIN MAX | | | | | | | Al | 0.002 {0.008 | 0.05 | 0.21 D/ 0.239 [0.249 | 6.07 | 6.33 | 14L B loo10 loos 1025 10.38 D| 0.239 |0.249 | 6.07} 6.33 | 16L Dlo.278|0.289 | 7.07| 7.33] 20L +) C } 0.004 10.008 10.09 1020 | |p[0.317 |o.328 | 8.07| 8.33 | 24L D SEE VARIATIONS - - - - | | | [ecTezosToz09 [5.20 sae | W2l0.397/0.407 [10.07 10.33 [eae e {0.0256 BSC |0.65 BSC H_ {0.301 |0.311 | 7.65 | 7.90 L_ {0.025 |0.037 | 0.63 | 0.95 a 0 8 0 8 MA AALVI PROPRIETARY INFORMATION TILE: PACKAGE OU APPROVAL TLINE, SSOP, 5.3X DOCUMENT CONTROL NO 21-0056 MAXLM 11 GO9VXVW/SO9VXVW/PO9OVXVWNMAX4604/MAX4605/MAX4606 5Q, Quad, SPST, CMOS Analog Switches Package Information (continued) C053 | 064 Coe | O00 O01 O09 Cy O07 | 0,010 CE NOTES: ISO | OLS 7 (1 on L DSE DO NOT INCLUDE MOLD FLASH aTnecebnedd CT MOLD FLAH OP PPOTPUCIOM: NOT Wece| he peel TO ERCEED 15mm 1,005" O01 O0e0 Wes] O,S0 3, LEADS TO BE COPLANAP WITHIN ste banana aa Meta 004" GAEDE | EWES | att | Le 7 4 CONTPOLLING DIMEMCIOM MILLIMETEP 5. MEETS JEDEC Mo0le#% 43 SHOWK IN ABOVE TABLE & = NUMBER OF PINS MAXIM [PACKAGE FAMILY OUTLINE: SOIC 150" ky E 1, Due DO NOT INCLUDE MOLD FLASH 2, MOLD FLASH OF PPOTPLUZIONS NOT TO E*CEED 15mm 06+ 3. COMTPOLLING DIMENTION: MILLIMETEP 4, MEETS JEDEC M2O01-%* AT CHOWN IN ABOVE TABLE 3. TIMILIAP TO JEDEC MO-0S53AB 6. MN = NUMBEP OF PING (LAVAXIAA | Peck AGE FAMILY QUTLINE: POIP 300" a RL SIME Cm ik 2 |-Lind 3 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 1998 Maxim Integrated Products Printed USA MAXIMA is a registered trademark of Maxim Integrated Products.