Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2254E (R) 8/16/17 Page 1 of 4 www.murata.com
Electrical Characteristics
Electrical Connections
Characteristic Sym Notes Min Typ Max Units
Center Frequency fC872.5 MHz
Insertion Loss, 865 to 880 MHz IL 2.7 3.5 dB
Amplitude Ripple, 865 to 880 MHz 0.7 1.5 dBP-P
VSWR, 865 to 880 MHz 1.5:1 2.0:1
Attenuation, Referenced to 0 dB:
dB
10 to 820 MHz 40 45
820 to 835 MHz 35 40
912 to 927 MHz 25 32
927 to 972 MHz 35 40
972 to 1300 MHz 40 45
Source Impedance ZS50
Load Impedance ZL50
Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator A01, YWWS
Standard Reel Quantity Reel Size 7 inch 500 Pieces/Reel
Reel Size 13 inch 3000 Pieces/Reel
Connection Terminals
Input 2
Output 5
Case Ground All others
SM3030-6
Low-loss RF SAW Filter
Miniature 3 x 3 mm SMD Package
Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating Value Units
Input Power Level +10 dBm
DC Voltage on any Non-grounded Terminal 3 V
Operable Temperature Range -45 to +125 °C
Specification Temperature Range -30 to +85 °C
Storage Temperature Range in Tape and Reel -40 to +85 °C
Maximum Soldering Profile, 5 cycles/10 seconds maximum 265 °C
872.5 MHz
SAW Filter
SF2254E
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4. The design, manufacturing process, and specifications of this filter are subject to change.
5. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
6. US and international patents may apply.
7. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Pb
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
50 ohm 50 ohm
52
1 , 3 , 4 , 6
S A W F i l t e r
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2254E (R) 8/16/17 Page 2 of 4 www.murata.com
Filter Passband Response
Filter Broadband Response
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2254E (R) 8/16/17 Page 3 of 4 www.murata.com
SM3030-6 Case
TOP VIEW BOTTOM VIEW
1
2
3
6
5
4
1
2
3
6
5
4
A
BC
DJ
EF
GH
I
K
K
O
MM
N
N
N
L
6-Terminal Ceramic Surface-Mount Case
3.0 X 3.0 mm Nominal Footprint
Case and PCB Footprint Dimensions
Case Materials
Dimension mm Inches
Min Nom Max Min Nom Max
A2.87 3.00 3.13 0.113 0.118 0.123
B2.87 3.00 3.13 0.113 0.118 0.123
C1.12 1.25 1.38 0.044 0.049 0.054
D0.77 0.90 1.03 0.030 0.035 0.040
E2.67 2.80 2.93 0.105 0.110 0.115
F1.47 1.60 1.73 0.058 0.063 0.068
G0.72 0.85 0.98 0.028 0.033 0.038
H1.37 1.50 1.63 0.054 0.059 0.064
I0.47 0.60 0.73 0.019 0.024 0.029
J1.17 1.30 1.43 0.046 0.051 0.056
K3.20 0.126
L1.70 0.067
M1.05 0.041
N0.81 0.032
O0.38 0.015
Materials
Solder Pad
Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel
Lid Plating 2.0 to 3.0 µm Nickel
Body Al2O3 Ceramic
Pb Free
PCB Footprint Top View
A01
YWWS
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. March 2015
SF2254E (R) 8/16/17 Page 4 of 4 www.murata.com
Tape and Reel Specifications
“B” Quantity Per Reel
Inches millimeters
7 178 500
13 330 3000
See Detail "A"
13.0
20.2
2.0
12.0
100 REF.
"B" REF.
COMPONENT ORIENTATION and DIMENSIONS
Carrier Tape Dimensions
Ao 3.35 mm
Bo 3.35 mm
Ko 1.40 mm
Pitch 8.0 mm
W 12.0 mm
RO.3
(MAX.)
Ko
SECTION A-A
0.3 ± 0.05
SECTION B-B
Bo
2.0 4.0
Ao Pitch
BB
AR0.5
(MAX.)
A
5.5
12.0
1.75
1.5
1.50
PIN #1
USER DIRECTION OF FEED