WORLD-BEAM(R) QS30 Series Sensors High-power opposed-mode sensors * * * * * * * * * * Excellent for applications where high sensing power is required due to long sensing range or contamination on lenses. * * Infrared beam with high excess gain -- range over 213 m (700') Excellent noise immunity Excellent optical performance throughout the sensing range Easy two frequency selection to help prevent crosstalk, see Application Note on page 3 Easy-to-read operating status indicators with bargraph display Bipolar discrete outputs, PNP and NPN Light Operate and Dark Operate models available Models available with 2 m or 9 m (6.5' or 30') cable or quick-disconnect fitting Tough ABS housing is rated IEC IP67; NEMA 6P; QD models are washdown tested to DIN 40050-9 (IP69K) Unique water/debris-shedding lens design reduces lens contamination; lens material survives impact, washdown and cleaning chemicals Encapsulated electronics Compact housing -- mounting versatility via popular 30 mm threaded barrel or side-mount Models Model Cable* Supply Voltage 4.6 m (15') Output Type B E A M 0 W I -0.3 m D (-1') T H -3.0 m (-10') Emitters QS30EX QS30EXQ 2 m (6.5') 5-wire Cable 5-pin Euro-style QD 3.0 m (10') 0.3 m (1') 10V dc to 30V dc -4.6 m (-15') -- QS30ARX QS30ARXQ 5-pin Euro-style QD QS30RRX 2 m (6.5') 5-wire Cable QS30RRXQ 5-pin Euro-style QD 61 m (200') 122 m (400') 183 m (600') 244 m (800') 305 m (1000') DISTANCE Figure 1. Beam Pattern Receivers 2 m (6.5') 5-wire Cable 0 100000 Bipolar NPN/PNP Light Operate 10V dc to 30V dc Bipolar NPN/PNP Dark Operate * 9 m (30') cables are available by adding suffix W/30 to the model number of any cabled sensor (for example, QS30EX W/30). A model with a QD connector requires a mating cable (see Cordsets on page 4). E X C E S S G A I N 10000 1000 100 10 1 0.3 m (1') 3m (10') 30 m (100') 300 m (1000') DISTANC E Figure 2. Excess Gain WARNING: Not To Be Used for Personnel Protection Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death. This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. P/N 115011 Rev. E 1/31/2012 0 115011 7 WORLD-BEAM(R) QS30 Series Sensors Overview Banner QS30 Series high-power opposed-mode sensors are extremely rugged, powerful and leakproof. They are designed to withstand the most demanding industrial applications, including high-pressure washdown areas. They are powerful enough to burn through heavy fog, dust, and most types of industrial and process contamination. The sensor's electronics are epoxy-encapsulated for maximum resistance to mechanical shock and vibration. The popular WORLDBEAM-style housing provides multiple mounting configurations in a minimum of space. The innovative circuitry used in these sensors provides the best EMI/RFI noise immunity of any non-synchronized emitter/receiver pair. For applications where optical crosstalk between multiple sensor pairs may be a problem, the sensors provide a choice between two frequencies (A and B). (Each emitter must be set to the same frequency as its receiver, see Sensor Alignment on page 2.) Light Operate and Dark Operate outputs are available, depending on the model. Each model has two outputs that switch simultaneously: one each NPN (sinking) and PNP (sourcing). Additional configuration options are available; contact the factory for information about the following options: * * * * Additional modulation frequency choices (up to four) Modified sensor gain ON-delay or OFF-delay settings Fixed modulation frequency models Each sensor has a green Power ON/OFF indicator and yellow indicators for the selected modulation frequency. In addition, receivers have a yellow LED that lights when the outputs are conducting, plus a 4-element light bar that indicates signal strength, relative to the switch point (the higher the number lit, the more light is received). Power ON/OFF (Green) Output Conducting (Yellow) Power ON/OFF (Green) Modulation Frequency Selection Indicators Signal Strength Light Bar Sensing Threshold Receiver Indicators Emitter Indicators Figure 3. Receiver and Emitter Indicators Sensor Configuration The modulation frequency (A or B) is selected by the state of the gray wire (on cabled models; pin 5 on QD models - see hookups...). A "+" voltage or no connection selects frequency A; connecting it to "-" selects frequency B. To disable (or inhibit) the emitter LED for testing the receiver, attach the white wire to "-" voltage. Sensor Alignment Adjust the emitter first, then the receiver. Verify that both sensors are wired for the same modulation frequency, then adjust the emitter's position until the receiver signal strength light bar indicates its highest amount of signal received (the highest number lit). Tighten the emitter mounting hardware, then repeat the process for the receiver. To achieve the best crosstalk immunity, position a single matched emitter within the receiver's field of view (15 degrees). When it is necessary to position an alternate emitter in the receiver's field of view, sensor alignment is required to ensure the matched frequency emitter provides the stronger signal to its receiver, and the alternate frequency emitter does not reduce the signal strength of the receiver (as indicated by the 4-element signal strength light). 2 www.bannerengineering.com - tel: 763-544-3164 P/N 115011 Rev. E WORLD-BEAM(R) QS30 Series Sensors Specifications Supply Voltage and Current Emitter: 10 to 30V dc (10% maximum ripple) at less than 70 mA Receiver: 10 to 30V dc (10% maximum ripple) at less than 22 mA (exclusive of load) Beam 875 nm, infrared Sensing Range Excess gain of 2 at 213 m (700') Output Configuration Bipolar current sinking (NPN) white wire; current sourcing (PNP) black wire Output Rating: 100 mA max OFF-state leakage current: less than 200 A ON-state saturation voltage: less than 1.5V @ 100 mA, less than 900 millivolts at 10 mA Protected against false power-up and continuous overload or short circuit of outputs Output Response 30 milliseconds ON and 30 milliseconds OFF; 5 ms repeatability Adjustments Light Operate/Dark Operate -- dependent on model selected Frequency via gray wire A: Gray (+) B: Gray (-) Emitter only: LED inhibit via white wire White (-) turns emitter LED OFF (to allow verification of sensor operation) Indicators Green LED: Power ON Frequency indicator (A or B) Receiver only: Yellow LED: Output conducting 4-LED Signal Strength light bar Environmental Rating Cabled models: IP67, NEMA 6P QD models: IP69K per DIN 40050-9 Construction ABS plastic housing; impact-resistant lens material Connection 5-wire cable (2 m or 9 m) or 5-pin integral Euro-style quickdisconnect fitting Operating Conditions Temperature: -20 to +60 C (-4 to +140 F) Relative Humidity: 90%; non-condensing Mounting Torque Maximum 4.5 Nm (40 in lbs) with included 30 mm mounting nut Certifications Application Notes 1. When multiple sensors are used in close proximity (see Figure 1 for separation distance), position sensors such that the alternate frequency emitter is not within the receiver's field of view. Contact the Banner Application team for additional information. 2. Prolonged outdoor use in direct sunlight may cloud the lens. Contact Banner for other outdoor solutions. Dimensions QD Models Cabled Models 43.0 mm (1.69") 9.0 mm (0.35") 34.0 mm (1.34") 22.0 mm (0.87") 32.5 mm (1.28") 3.5 mm (0.14") 33.0 mm (1.30") 5.0 mm (0.20") 21 mm (0.83") Bracket dimensions are shown on page 5. P/N 115011 Rev. E 12.5 mm (0.49") 2 x o3.3 mm (0.125") max. torque 0.7 Nm (6 in lbs) www.bannerengineering.com - tel: 763-544-3164 M30 x 1.5 Thread max. torque 6 Nm (53 in lbs) with included 30 mm mounting nut 1.3 mm (0.05") 44.0 mm (1.73") 13.0 mm (0.51") 3 WORLD-BEAM(R) QS30 Series Sensors Wiring Receiver Emitter Frequency A bn bu wh gy Frequency A + 10 - 30V dc - Beam Inhibit Frequency Select Frequency B bn bu wh gy bn bu wh bk gy + 10 - 30V dc - 100 mA max. load Load Load Frequency Select Frequency B + bn bu wh bk gy 10 - 30V dc - Beam Inhibit Frequency Select + - 10 - 30V dc 100 mA max. load Load Load Frequency Select Accessories Cordsets Quick Disconnect 5-Pin M12/Euro-Style Cordsets (straight connector) MQDC1-506, 2 m (6') 42 Typ. [1.65"] MQDC1-515, 5 m (15') MQDC1-530, 9 m (30') M12 x 1 o 15 [0.59"] White Brown 5-Pin M12/Euro-Style Cordsets (right-angle connector) MQDC1-506RA, 2 m (6') Blue Black Gray 32 Typ. [1.26"] MQDC1-515RA, 5 m (15') 30 Typ. [1.18"] MQDC1-530RA, 9 m (30') M12 x 1 o 14.5 [0.57"] 4 www.bannerengineering.com - tel: 763-544-3164 P/N 115011 Rev. E WORLD-BEAM(R) QS30 Series Sensors Brackets SMBQS30L * 14-gauge, stainless steel right-angle bracket SMBQS30LT for cable models * Clearance for M4 (#8) hardware * 12 tilt adjustment 20 20 R35.0mm [R1.38"] o4.3mm [o0.17"] 4.5mm [0.18"] * 14-gauge stainless steel for QD models with right-angle cables * Tall right-angle mounting bracket * 8 Tilt adjustment R35.0mm [R1.38"] 44.0mm [1.73"] 44.0mm [1.73"] o4.3mm [o0.17"] 4.5mm [0.18"] 11.0mm [0.43"] 11.0mm [0.43"] 22.0mm [0.87"] R1.7mm [R0.07"] 24.0mm [0.95"] 24.0mm [0.95"] 22.0mm [0.87"] 33.0mm [1.3"] 64.4mm [2.54"] R33.0mm [R1.3"] 91.4mm [3.60"] 59.4mm [2.4"] 24 1.9mm [0.07"] SMBQS30Y * * * * 2 X R 33.0 mm (1.30") R33.0mm [R1.3"] 16 86.4mm [3.4"] 1.9mm [0.07"] Heavy-duty die-cast bracket M18 vertical mounting option 8 tilt adjustment with cabled units Nuts and lockwasher included SMB30SC * 130 mm swivel bracket, barrel mount * Black reinforced thermoplastic polyester * Includes stainless steel mounting and swivel locking hardware 17.0 mm (0.67") 7.0 mm (0.28") 4 X O 3.3 mm (0.13") 50.8 mm (2.00") M30 x 1.5 internal thread 33 mm (1.30") 56 mm (2.20") 12.7 mm (0.50") 58.7 mm (2.31") 30.0 mm (1.18") 18.0 mm (0.71") M18 X 1 66.5 mm (2.62") 29.0 mm (1.14") 26.5 mm (1.04") 16.35 mm (0.64") 13.3 mm (0.52") 35.0 mm (1.38") 24.0 mm (0.94") Other Compatible Mounting Brackets (see Banner Photoelectric catalog or website for more information): * SMB30MM * SMB30A P/N 115011 Rev. E www.bannerengineering.com - tel: 763-544-3164 5 WORLD-BEAM(R) QS30 Series Sensors Contact Us For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Banner Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia -- China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500, Fax: 86-21-54894511 www.bannerengineering.com.cn sensors@bannerengineering.com.cn Europe Banner Engineering Europe Park Lane Culliganlaan 2F Diegem B-1831 BELGIUM Tel: 32-2 456 07 80, Fax: 32-2 456 07 89 www.bannereurope.com mail@bannereurope.com Latin America Contact Banner Engineering Corp. (US) or e-mail: Mexico:mexico@bannerengineering.com Brazil: brasil@bannerengineering.com Asia -- Japan Banner Engineering Japan Cent-Urban Building 305 Asia -- Taiwan 3-23-15, Nishi-Nakajima Banner Engineering Taiwan Yodogawa-Ku, Osaka 8F-2, No. 308 532-0011 JAPAN Section 1, Neihu Road Tel: 81-6-6309-0411, Fax: Taipei 114 81-6-6309-0416 Tel: 886-2-8751-9966, Fax: www.bannerengineering.co.jp 886-2-8751-2966 mail@bannerengineerwww.bannerengineering.co.jp ing.com.tw info@bannerengineering.com.tw Asia -- India Banner Engineering India Pune Head Quarters Office No. 1001 Sai Capital Opp. ICC Senapati Bapat Road Pune 411016 INDIA Tel: 91-20-66405624, Fax: 91-20-66405623 www.bannerengineering.co.in india@bannerengineering.com Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.