•40 pin ZIF socket
accepts both 300/600
mil DIP devices up to
40 pin
•Advanced pin drivers
allow varying voltages
to be applied to any
pin delivering signals
without overshoot,
increasing
programming yield
•Pin drivers operate
down to 1.8V so you'll
be ready to program
the full range of
tomorrow’s advanced
low-voltage devices
•USB 2.0/1.1
connectivity allowing
fast and easy
connection to PC’s and
laptops
•Upgradeable to 40Pro
programmer
The Dataman MEMPro is a PC based universal 40-pin memory
programmer with USB 2.0 connectivity. The MEMPro is built to meet
the demands of development labs and field engineers for specialized
programming.
Dataman MEMPro is a small, fast and powerful programmer supporting
a huge range of programmable memory types - EPROM, EEPROM,
NVRAM, Flash EPROM and serial EEPROM - including low voltage
types. MEMPro isn't only a programmer, but also a static RAMs tester.
Hardware:
General
• 40 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of the socket.
Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or
ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program
the full range of today's advanced low-voltage devices
• The programmer performs device insertion tests and contact checks before it programs each device. These
capabilities, supported by signature-byte check help prevent chip damage due to operator error
• MEMPro programmer performs programming verifications at the marginal level of supply voltage, which
improves programming yield, and guarantees long data retention
• Easily upgradeable to the 40Pro programmer
• Various socket converters are available to handle device in PLCC, SOIC, SSOP, TSOP, TSSOP, TQFP, QFN (MLF)
and other packages
Base unit (DAC)
• Two D/A converters for VCCP and VPP, controllable rise and fall time
• VCCP range 2V..7V/350mA
• VPP range 2V..25V/200mA
• USB 2.0/1.1 compatible interface
• Auto calibration
• Self test capability
Dataman MEMPro www.dataman.com
7773_Data sheet Mem Pro 3/5/07 13:45 Page 1
ZIF socket pindriver
• 40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices
up to 40-pins
• Pindrivers: 40 TTL pindrivers, specialized GND/VCC/VPP pindriver
• FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver
pins; level H selectable from 1.8V up to 5V
• Continuity test: each pin is tested before every programming operation
ISP connector (useable after upgrade to 40Pro)
• 10-pin male type with miss insertion lock
• 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable
from 1.8V up to 5V to handle all (low-voltage including) devices
• 1x VCCP voltage (range 2V..7V/100mA) and 1x VPP voltage (range
2V..25V/50mA)
• Programmed chip voltage (VCCP) with both source/sink capability and
voltage sense
Software:
User Interface
• Programmer is driven by an easy-to-use control program with pull-down
menus, hot keys and on-line help. Selection of device is performed by its
class, by manufacturer or simply by typing a fragment of vendor name
and/or part number
• Standard device-related commands (read, blank check, program, verify, erase)
are enhanced by some test functions (insertion test, signature-byte check),
and some special functions (autoincrement)
• All known data formats are supported. Automatic file format detection and
conversion during loading of file
• The rich-featured autoincrement function enables one to assign individual
serial numbers to each programmed device - or simply increments a serial
number, or the function enables one to read serial numbers or any
programmed device identification signatures from a file
• The software also provides extensive information about programmable
devices including detailed drawings of all available packages. The software
also provides explanations of chip labelling (prefixes and suffixes) for each of
the supported chips
• Keeping your programmer software up to date can be a costly business with
some programmers. Dataman offers completely FREE software updates
whenever you need them. The latest software is always available from our
website
The Dataman MEMPro supports over 8,000 of the most popular memory devices
in use today - with future devices being added monthly. Dataman MEMPro
coverage includes the following device types:
Programmer (ZIF socket)
• EPROM: NMOS/CMOS, 27xxx and 27Cxxx series, with 8/16 bit data width, full
support of LV series
• EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data
width, full support of LV series
• Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx
series, with 8/16 bit data width, full support of LV series
• Serial E(E)PROM: 24Cxxx, 24Fxxx, 25Cxxx, 45Dxxx, 59Cxxx, 25Fxxx, 25Pxxx,
NVM3060, 85xxx, 93Cxxx, full support for LV series
• Configuration (EE)PROM: 37LVxx, XC17xxxx, AT17xxx, LV series including
• NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD
U63x series
Package Includes:
Dataman MEMPro Universal Memory Programmer
• Dimensions: 160x95x35 mm (6.3x3.7x1.4 inches)
• Weight: 500g (17.65 oz)
Switching Power Supply Adaptor
• Input: 100-240V @ 50-60Hz & 400mA
• Output: 15V @ 0.5A, 7.5W
• Moulded USB Cable
• ISP cable (useable after upgrade to 40Pro)
• Diagnostic POD for self test of the programmer
• Anti-dust cover for ZIF socket
• User manual
• Software
• Optional range of adapters and socket converters also available
Warranty and Support:
• 30 day money back guarantee* - If you don't like it, send it back
• One year guarantee - One year parts and labour warranty, on the MEMPro
device programmer
• Life-Time Technical Support - MEMPro technical support is available free via
our website and telephone helpdesk for life
• Life-Time Software Updates - MEMPro software updates are available free
via our website for life
*Applies to orders from UK/US office only
IN THE UK…
Dataman Programmers Ltd.
Station Road, Maiden Newton
Dorset DT2 0AE, UK
Tel (01300) 320719
Fax (01300) 321012
IN THE US…
Dataman Inc.
215 East Michigan Avenue
Orange City, Florida 32763 USA
Tel (386) 774-7785
Fax (386) 774-7796
www.dataman.com
Available from…
7773_Data sheet Mem Pro 3/5/07 13:45 Page 2
