No. SS2-MTG200-0100 (Rev.1) MagneW Two-wire PLUS Smart Two-wire Electromagnetic Flowmeter Model MTG18A (Integral type) Model MTG14C/MTG18B (Remote type) OVERVIEW The MagneW Two-wire PLUS is a high performance electromagnetic flowmeter based on field proven Yamatake two-wire loop powered technology. The MagneW Two-wire PLUS offers the stable and accurate measurement of a traditional magflow meter with low power consumption. The result is a lower overall cost of ownership. FEATURES Two-wire operation MagneW Two-wire PLUS significantly reduces installation costs when compared to a traditional four wired magnetic flowmeter. Integral type High accuracy and stable output MagneW Two-wire PLUS provides high accuracy ( 0.5% of rate) and its output is as stable as current four wired magnetic flowmeters. Minimum measurable fluid conductivity The MagneW Two-wire PLUS offers a minimum process fluid conductivity of 10 S/cm which is the best among two-wire magflow meters thereby maximizing applicability. Wider range in size MagneW Two-wire PLUS offers wider range in detector size. Detector size: 2.5 to 200 mm. Remote type APPLICATION Wafer and flange style, integral and remote style available The MagneW Two-wire PLUS is available integral or remote. Flange or wafer, making the selection of the right meter for the application simple. Specifications are subject to change without notice. (1) Corrosive liquid measurement (2) Chemical solution measurement (3) Drainage/waste disposal fluid measurement (4) Drinking water and waste water service (5) Industrial/agricultural water measurement (6) Seawater measurement The above flow measurements are applicable. -1- First issue: May. 2003 Rev.1: Mar. 2004 No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation FUNCTIONAL SPECIFICATIONS Display Display: LCD Main display: 7-segment, 8 digits Sub display: 16 digits, 2 lines Display contents: Demonstrates three values simultaneously % flow rate, Actual flow rate, Totalized value Enclosure rating NEMA TYPE 4X, IEC IP67 Hazardous Areas certifications The following is planned to make approval applications. FM CL I,II,III, DIV 1, Groups A,B,C,D,E,F&G,T4 FM NI for CL I,II,III, DIV 2, GPs A,B,C,D,F&G, T4 Data setting Operation by four key switches Output signal Analog output 4 to 20mA DC Damping Digital output DE Analog or Digital output is selectable. Low flow cutoff Adjustable between 0.5 and 199.9 seconds. Adjustable between 0 and 10% of setting range. Below selected value, output is driven to the zero flow rate signal level. Pulse output Open collector output (30V DC, 100 mA max.) Pulse frequency: 0.0001 to 200 Hz Pulse width: 1 ms to 1 s Dropout Adjustable between 0 and 10% of setting range. Below selected value, pulse output is cut. Contact output Open collector output (30V DC, 100 mA max.) Pulse or contact output is selectable Lightning protection 12 kV, 1000A Equipped with the lightning arrester in the power source and external output terminals. Communication protocol SFC communication and HART(R) communication Load resistance characteristic of communication External power supply 21.05 to 42V DC for communication. Power failure An EEPROM retains data record of totalized value when pulse output is used (retention period approximately 10 years). Power supply Load resistance () 2 1 21.05<V<30 R= V-15.6 0.0218 15.6 to 42V DC (without communication) 21.05 to 42V DC (with communication) 2 30<V<42 R= V-14.25 0.02383 Size Wafer style 25, 40, 50, 65, 80, 100 mm (1, 11/2, 2, 21/2, 3, 4 inches) 1 Flange style 2.5, 5 mm (0.1, 0.2 inch) (Model MTG18A only) 10, 15, 25, 40, 50, 65, 80, 100, 150, 200 mm (3/8, 1/2, 1, 11/2, 2, 21/2, 3, 4, 6, 8 inches) Flange rating Power supply (V DC ) ANSI150, ANSI300, DIN PN10, DIN PN16, DIN PN25, JIS10K, JIS20K, JIS30K Note) The load resistance of 250 or more is necessary for communications of SFC and the HART(R) communicator. Ambient temperature limits -20 to 60C (-4 to 140F) Flow unit Ambient humidity limits Volume flow: m3, L, cm3, G (gallon), mG, kG, B (barrel), IG (imperial gallon), mIG, kIG Mass flow: t, kg, g, lb Time: d, h, m, s 10 to 90% RH -2- Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) Temperature range and pressure range of process fluid Refer to the following. Size: 2.5 to 10 mm (0.1 to 3/8 inch) Size: 15 to 200 mm (1/2 to 8 inches) 2.94 MPa (426 psi) 2.94 MPa (426 psi) 1.96 MPa (284 psi) 0.98 MPa (142 psi) -0.098 MPa (-14.2 psi) -20 C (-4 F) -0.098 MPa (-14.2 psi) -20 C (-4 F) 80 C 100 C (176 F) (212 F) 80 C (176 F) 120 C 130 C (248 F) (266 F) Measurable electrical conductivity 10 S/cm or greater 50 S/cm or greater (10 mm (3/8 inch), 15 mm (1/2 inch) for remote type) Measurement flow range Size Maximum flow velocity range is 0 to 0.3 m/s (0 to 0.98 ft/s) Maximum flow velocity range is 0 to 10 m/s (0 to 32.8 ft/s) Minimum range Maximum range mm inches m3/h GPM 2.5 5 10 15 25 40 50 65 80 100 150 200 0.1 0.2 3/8 1/2 1 11/2 2 21/2 3 4 6 8 0 to 0.00531 0 to 0.02121 0 to 0.08483 0 to 0.1909 0 to 0.5302 0 to 1.358 0 to 2.121 0 to 3.584 0 to 5.429 0 to 8.483 0 to 19.09 0 to 33.93 0 to 0.02335 0 to 0.09337 0 to 0.3735 0 to 0.8404 0 to 2.335 0 to 5.976 0 to 9.337 0 to 15.78 0 to 23.90 0 to 37.35 0 to 84.04 0 to 149.4 m3/h 0 to 0.1767 0 to 0.7068 0 to 2.827 0 to 6.361 0 to 17.67 0 to 45.23 0 to 70.68 0 to 119.4 0 to 180.9 0 to 282.7 0 to 636.1 0 to 1130 Conversion factor K GPM 0 to 0.778 0 to 3.112 0 to 12.44 0 to 28.01 0 to 77.80 0 to 199.1 0 to 311.2 0 to 525.9 0 to 796.7 0 to 1244 0 to 2801 0 to 4979 56.59 14.15 3.537 1.572 0.5659 0.2210 0.1415 0.08371 0.05526 0.03537 0.01572 0.008842 K = Conversion factor = 1/3600 x 4/(D2) x 10002 D = Size (mm) Q = Flow rate (m3/h) Velocity V (m/s) = K x Q PERFORMANCE SPECIFICATIONS Analog output accuracy <Size: 2.5, 5 mm (0.1, 0.2 inch)> Vs = velocity of setting range (m/s) Velocity during measurement < Vsx50% Vs (m/s) Velocity during measurement > Vsx50% 1.0 Vs 10 0.5% of rate 0.5% of Vs 0.3 Vs 1.0 0.5 ------- % of rate Vs 0.5 ------- % 0.5 Vs <Size: 10, 15 mm (3/8, 1/2 inch)> Vs = velocity of setting range (m/s) Velocity during measurement < Vsx40% Vs (m/s) Velocity during measurement > Vsx40% 1.0 Vs 10 0.5% of rate 0.5% of Vs 0.3 Vs 1.0 0.5 ------- % of rate Vs 0.4 ------- % 0.5 Vs <Size: 25 to 200 mm (1 to 8 inches)> Vs (m/s) Velocity during measurement > Vsx30% Vs = velocity of setting range (m/s) Velocity during measurement < Vsx30% 1.0 Vs 10 0.5% of rate 0.5% of Vs 0.3 Vs 1.0 0.5 ------- % of rate Vs 0.3 ------- % 0.5 Vs -3- No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation PHYSICAL SPECIFICATIONS INSTALLATION Converter case finishing Electrical connection 1/2NPT internal thread (must be selected for FM approval) CM20 internal thread G1/2 internal thread Standard Baked acryl paint Corrosion-proof Baked epoxy paint Remote converter mounting Converter case material Wall mounting, 2-inch pipe mounting Aluminum alloy Grounding Display cover material Grounding resistance should be less than 100 . Tempered glass Pipe connection Terminal box finishing (Model MTG18B only) Wafer style (Size: 25 to 100 mm (1 to 4 inches)) Flange style (Size: 2.5 to 200 mm (0.1 to 8 inches)) Standard Baked acryl paint Length of straight pipe Corrosion-proof Baked epoxy paint Required straight pipe length clearance on the upstream side and the downstream side, while installing the detector. Terminal box material (Model MTG18B only) Upstream side A minimum 5D straight pipe length is required. A minimum 10D straight pipe length is required if a diffuser/valve/pump is installed upstream side. Aluminum alloy Detector main body materials Case material Size 2.5 to 15 mm (0.1 to 1/2 inch): SCS13 stainless steel Size 25 to 200 mm (1 to 8 inches): SUS304 stainless steel Downstream side 2D straight pipe length is recommended. (Where D is the nominal bore diameter of the detector) Measuring pipe material SUS304 stainless steel Cable between converter and detector (Remote type) Flange Length 70 m (233 ft) or under (25 mm (1 inch) to 200 mm (8 inches)) 30 m (98 ft) or under (10 mm (3/8 inch), 15 mm (1/2 inch)) SUS304 stainless steel (size 2.5 to 65 mm (0.1 to 21/2 inches)) Carbon steel + corrosion-preventive painting (size 80 to 200 mm (3 to 8 inches)) Process wetted materials Outside diameter 11.4 mm (0.45 inch) Lining PFA Electrode SUS316L, Hastelloy C, Titanium, Tantalum, Nickel, Zirconium, Platinum-Iridium Grounding ring SUS316, Hastelloy C, Titanium, Tantalum, Zirconium, Platinum -4- Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) MODEL SELECTION MagneW Two-wire PLUS Model MTG18A - I II III IV V VI VII VIII IX X XI - XII XIII - Options (some options can be selected per each model) Selections Optional selections Options MTG18A I Line size II Lining III Pipe connection IV Electrode V Grounding ring VI Wiring connection VII Face to face dimension VIII Installation / Display direction IX Calibration X Output / communication XI Approval 2.5 mm (0.1 inch) (flange type only) 002 *1 5 mm (0.2 inch) (flange type only) 005 *1 10 mm (3/8 inch) (flange type only) 010 *1 15 mm (0.5 inch) (flange type only) 015 *1 25 mm (1 inch) 025 40 mm (11/2 inches) 040 50 mm (2 inches) 050 65 mm (21/2 inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 150 mm (6 inches) (flange type only) 150 200 mm (8 inches) (flange type only) 200 PFA P Wafer JIS10K 11 Wafer JIS16/20K 12 Wafer JIS30K 13 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Wafer DIN PN40 44 Flange JIS10K J1 Flange JIS20K J2 Flange JIS30K J3 Flange JIS10K for 10 mm size flange *2 J4 Flange JIS20K for 10 mm size flange *2 J5 Flange ANSI 150 A1 Flange ANSI 300 A2 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange DIN PN40 D4 SUS316L L Hastelloy C C Titanium K Zirconium H Tantalum T Nickel N Platinum-iridium P SUS316 S Hastelloy C C Titanium K Zirconium H Tantalum T Platinum P Nickel N G1/2 internal thread A G1/2 internal thread with plastic water tight gland B G1/2 internal thread with brass Ni-plated watertight gland C 1/2NPT internal thread (must be selected for FM approval) D CM20 internal thread E G1/2 internal thread with two plastic watertight glands J G1/2 internal thread with two brass Ni-plated watertight gland K Standard A Replacement for SMT3000 (for wafer type 40 to 100 mm) S Horizontal piping / Right side viewed from upstream Horizontal piping / Left side viewed from upstream Horizontal piping / Downstream side Horizontal piping / Upstream side Vertical piping / Right side of piping / Flow direction: Upward Vertical piping mounting / Left side of piping / Flow direction: Upward Standard Volume flow 4-20mA DC output/with SFC communication Volume flow DE output/with communication Volume flow 4-20mA DC output with HART communication None FM approval, CL I, II, III, DIV.1, GPs A, B, C, D, E, F & G, T4 FM approval, CL I, II, III, DIV.2, GPs A, B, C, D, F & G, T4 -5- X A B C None Test report Traceability certificate Material certificate (electrode/grounding ring) Options Basic model no. G Gasket for plastic piping J Tropical treatment K with tagging on the converter housing *3 L with tag number plate wired to the flowmeter X Finish / 2 paint Corrosion-proof finish XII X Bolt and None XIII 2 nut SUS304 (only for wafer type) Display direction code "A" Display direction code "B" Display Direction of flow Direction of flow Display Display direction code "C" Display direction code "D" Display Display Direction of flow A B C D E F Direction of flow Display direction code "E" Display direction code "F" Direction of flow A A C H Note) X 1 2 Direction of flow *1: Flange of size 2.5 to 15 mm detector is 15 mm flange. *2: Available for size 2.5 to 10 mm detector. *3: Must be selected if tagging is required. No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation MagneW Two-wire PLUS Wafer/Flange remote type converter Model MTG14C - I II III IV - Options (some options can be selected per each model) Basic model no. Selections MTG14C I IV Analog output / communication Volume flow 4-20 mA DC output / with SFC communication Volume flow DE output / with communication Volume flow 4-20 mA DC output / with HART communication Wiring connection G1/2 internal thread G1/2 internal thread with a plastic water-tight gland G1/2 internal thread with a brass Ni-plated water-tight gland 1/2NPT internal thread CM20 internal thread Converter mounting Wall mounting with standard bracket 2-inch pipe mounting with standard bracket Approval None V Option II III A C H A B C D E G H X - None Traceability certificate With the Tag number plate on the converter housing Corrosion-proof paint X B K 2 MagneW Two-wire PLUS Wafer/Flange remote type cable Model SMC11 - I II III Basic model no. Selections SMC11 I II III Cable Terminals for detector Terminals for converter 2m (6 feet 8 inches) 3m (10 feet) 4m (13 feet 4 inches) 5m (16 feet 8 inches) 10 m (33 feet 4 inches) 15 m (50 feet) 20 m (66 feet 8 inches) 30 m (100 feet) 40 m (133 feet 4 inches) 50 m (166 feet 8 inches) 60 m (200 feet) 70 m (233 feet 4 inches) With terminals With terminals -6- 02 03 04 05 10 15 20 30 40 50 60 70 A A Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) MagneW Two-wire PLUS Wafer/Flange remote type detector Model MTG18B - I II III IV V VI VII VIII IX - Options (some options can be selected per each model) Basic model no. Selections Options I Diameter II Lining III Pipe connection IV Electrode V Grounding ring VI Wiring connection VII Face to face dimension VIII Calibration IX Approval 10 mm (3/8 inch) 010 15 mm (1/2 inch) 015 25 mm (1 inch) 025 40 mm (11/2 inches) 040 50 mm (2 inches) 050 65 mm (21/2 inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 150 mm (6 inches) 150 200 mm (8 inches) 200 PFA P Wafer JIS10K 11 Wafer JIS16/20K 12 Wafer JIS30K 13 Wafer JIS 3451 F12 (Size: 80 mm or larger) 51 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer JPI 150 61 Wafer JPI 300 62 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Flange JIS10K J1 Flange JIS20K J2 Flange JIS30K J3 Flange JIS10K for 10 mm size flange J4 Flange JIS20K for 10 mm size flange J5 Flange JIS3451 F12 (Size: 80 mm or larger) G1 Flange ANSI 150 A1 Flange ANSI 300 A2 Flange JPI 150 P1 Flange JPI 300 P2 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 SUS316L L Hastelloy C C Titanium K Zirconium H Tantalum T Nickel N Platinum-iridium P SUS316 S Hastelloy C C Titanium K Zirconium H Tantalum T Platinum P G1/2 internal thread G1/2 internal thread with plastic water-tight gland G1/2 internal thread with brass Ni-plated water-tight gland 1/2NPT internal thread CM20 internal thread Standard Yamatake SMT3000 wafer type Standard calibration None -7- X A B C G K 2 4 A B C D E A S A X Options MTG18B None Test report Traceability certificate Material certificate (electrode/ grounding ring) Gasket for plastic piping With the Tag number plate on the terminal box Corrosion-proof paint Attached stainless steel 304 bolts and nuts for installation *1 *1: Available for wafer type. No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation DIMENSIONS All dimensions are in millimeters, dimensions in brackets ( ) are in inches (inch). Model MTG18A - Flange type size 2.5 mm (0.1 inch) to 15 mm (1/2 inch) - Flange type size 25 mm (1 inch) (5.33) (5.35) Flange type (3.37) Name plate (1.97) Size 2.5 mm to 15 mm (0.1 inch to 1/2 inch) (10.63) (2.76) ( 4.41) (0.98) (5) (1.85) M4 Grounding terminal Grounding ring (2.83) (2.80) Case (0.08) Flange (3.54) Electrode L Refer to Note 1 ( ) ( 0.35 ( 2)) (4.33) Terminal (5.33) (5.35) Name plate (1.97) Symbol (3.37) Description Flow rate signal Grounding Pulse output or contact output (selectable) (2.76) ( 4.41) (0.98) (5) (1.85) M4 Grounding terminal Grounding ring (3.03) Case Flange type Flange Size 25 mm (1 inch ) (7.87) Electrode Refer to Note 1 Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 1 Model no. Size mm (inch) 2.5 to 10 (0.1 to3/8) 15 (1/2) 25 (1) J1 J2 J3 10K 20K 30K 160 6.8 200 7 267 63 9.2 160 7 200 7.2 267 63 9.5 160 8 200 8.2 269 65 10.3 J4 J5 A1 A2 D1/D2 D3/D4 DIN 10K 20K 150 300 PN 10/16 PN 25/40 160 (6.3) 6.4 (14.1 lb) 200 (7.87) 6.6 (14.6 lb) 258 (10.16) 54 (2.13) 8.4 (18.5 lb) 160 (6.3) 6.9 (15.2 lb) 200 (7.87) 7.1 (15.7 lb) 266 (10.47) 62 (2.44) 9.5 (20.9 lb) JIS Flange rating Dimension L Weight (kg) Dimension L Weight (kg) H Dimension H1 Weight (kg) ANSI 10 mm flange 10 mm flange 160 6.7 200 6.9 - -8- 160 6.8 200 7 - 160 6.9 200 7.1 262 58 9.1 160 7.1 200 7.3 262 58 9.4 Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) Model MTG18A - Flange type size 40 mm (11/2 inch) to 100 mm (4 inches) (5.33) (5.35) Name plate (3.37) (1.97) (2.76) ( 4.41) (5) (0.98) (1.85) M4 Grounding terminal H2 Case Grounding ring Flange (7.87) Electrode Refer to Note 1 Symbol Description Flow rate signal Flange type Grounding Pulse output or contact output (selectable) Size 40 mm to 100 mm (11/2 inch to 4 inches) Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 2 Size mm (inches) 40 (1.5) Model no. Flange rating Dimension Weight 50 (2) Dimension Weight 65 (2.5) Dimension Weight 80 (3) Dimension Weight 100 (4) Dimension Weight H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) J1 10K 296 85 84 8.3 310 90 93 11.9 329 102 100 13.9 345 110 108 14.4 367.5 120 120.5 20.2 J2 JIS 20K 296 85 84 8.6 310 90 93 12 329 102 100 14 354 119 108 16.7 376.5 129 120.5 23.7 J3 A1 A2 D1/D2 ANSI 30K 307 96 84 11 316 96 93 13.7 343 116 100 15.7 359 124 108 20.4 384.5 137 120.5 28.6 150 288 (11.34) 77 (3.03) 84 (3.31) 7.8 (17.2 lb) 308 (12.13) 88 (3.46) 93 (3.66) 12.3 (27.1 lb) 330 (12.99) 103 (4.06) 100 (3.94) 14.3 (31.5 lb) 346 (13.62) 113 (4.45) 108 (4.25) 17.3 (38.1 lb) 378.5 (14.90) 131 (5.16) 120.5 (4.74) 25.1 (55.3 lb) -9- 300 305 (12.01) 94 (3.7) 84 (3.31) 10.1 (22.3 lb) 316 (12.44) 96 (3.78) 93 (3.66) 13.8 (30.4 lb) 388 (13.31) 111 (4.37) 100 (3.94) 15.8 (34.8 lb) 359 (14.13) 124 (4.88) 108 (4.25) 21.3 (47.0 lb) 392.5 (15.45) 145 (5.71) 120.5 (4.74) 34.2 (75.4 lb) D3/D4 DIN PN 10/16 302 91 84 8.7 316 96 93 13.3 334 107 100 15.3 354 119 108 14.4 373.5 126 120.5 19.6 PN 25/40 302 91 84 9.7 316 96 93 13.8 334 107 100 15.8 354 119 108 16.5 381.5 134 120.5 23.4 No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation Model MTG18A - Flange type size 150 mm (6 inches) and 200 mm (8 inches) (5.33) (5.35) (1.97) (3.37) (0.98) (2.76) ( 4.41) (5) (1.85) Case H2 M4 Grounding terminal Grounding ring Flange Electrode L Refer to Note 1 Symbol Description Flow rate signal Flange type Grounding Pulse output or contact output (selectable) Size 150 mm and 200 mm (6 inches and 8 inches) Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 3 Size mm (inches) Model no. Flange rating Dimension 150 (6) 200 (8) L H H1 H2 Weight (kg) Dimension L H H1 H2 Weight (kg) J1 10K 300 462 175 160 34.4 350 508 196 185 49.8 J2 JIS 20K 300 476 189 160 41.7 350 515 203 185 59.8 J3 A1 A2 D1/D2 ANSI 30K 150 300 PN 10/16 300 300 (11.81) 300 (11.81) 300 487 461 (18.15) 483 (19.02) 465 200 174 (6.85) 196 (7.72) 178 160 160 (6.3) 160 (6.3) 160 54.3 37.2 (82.0 lb) 56.2 (123.9 lb) 30.7 350 350 (13.78) 350 (13.78) 350 531 516 (20.31) 537 (21.14) 514 219 204 (8.03) 225 (8.86) 202 185 185 (7.28) 185 (7.28) 185 87 61.8 (136.2 lb) 90.8 (200.2 lb) 48.1 - 10 - D3 DIN PN 25 300 473 186 160 38.6 350 526 214 185 68.5 D4 PN40 300 473 186 160 38.6 350 534 222 185 72 Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) Model MTG18A - Wafer type size 25 mm (1 inch) to 100 mm (4 inches) (5.33) Name plate (5.35) (3.37) (1.97) H (2.76) (0.98) ( 4.41) (5) (1.85) Case M4 grounding terminal (H1) H2 D Grounding ring L Electrode Refer to note1 Symbol Description Flow rate signal Wafer type Grounding Pulse output or contact output (selectable) Size 25 mm and 100 mm (1 inch and 4 inches) Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 4 Flange rating Face-to-face dimension code L Dimension size Weight 25 mm (1 inch) A 40 mm (11/2 inch) A S 50 mm (2 inches) A S 65 mm (21/2 inches) A 80 mm (3 inches) A S 100 mm (4 inches) A S 94 (3.7) 80 (3.15) 98 (3.86) 86 (3.39) 104 (4.09) 96 (3.78) 106 (4.17) 130 (5.12) 120 (4.72) 150 (5.91) H 238 (9.37) 254.5 (10.02) 272 (10.71) 289 (11.38) 302 (11.89) 327 (12.87) H1 34 (1.34) 43.5 (1.71) 52 (2.05) 62 (2.44) 67 (2.64) 79.5 (3.13) H2 77 (3.03) 84 (3.31) 93 (3.66) 100 (3.94) 108 (4.25) 120.5 (4.74) D 68 (2.68) 87 (3.43) 104 (4.09) 124 (4.88) 134 (5.28) 159 (6.26) (kg) 3.7 (8.2 lb) 3.8 4.3 4.4 5.0 (8.4 lb) (9.5 lb) (9.7 lb) (11.0 lb) - 11 - 5.5 (12.1 lb) 6.4 7.1 8.2 9.2 (14.1 lb) (15.7 lb) (18.1 lb) (20.3 lb) No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation Model MTG14C - Converter (0.75) (R0.16) (3.63) (4.41) (R0.49) (0.13) (10.67 +0.040 ) Plate (10.12) (R0.31) (R0.49) (0.63) (2.91+0.02) (0.77) (R0.49) (1.77) (1.19 max.) Wall mounting dimension (1.77) (9.92) (2.74) (4.36) Wall mounting (4.41) (3.63) Grounding Pulse output or contact (selectable) Excitation output Flow rate signal input (1.77) (1.77) (4.92) (6.30) PULSE/ STATUS OUT X Y A B C Flow rate signal (1.19 max.) I-OUT Description (0.63) Symbol (10.12) Terminal * Terminal screw: M4 2-inch pipe mounting - 12 - (2.74) (4.36) (1.23) Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) Model MTG18B - Detector - Flange type size 10 mm (3/8 inch) and 15 mm (1/2 inch) - Flange type size 25 mm (1 inch) Blind plug (1.19 max.) (3.31) (1.85) (0.98) (3.31) Waterproof gland (optional) Size 10 mm and 15 mm (3/8 and 1/2 inch) Tag plate (2.80) Nameplate Grounding ring (0.08) (2.83) (7.48) Flange type Terminal box (3.54) (4.43) (2.05) Electrode 9 ( 2) ( 0.35 ( 2)) Refer to note 1 (4.43) Terminal Blind plug (1.19 max.) (3.31) (1.85) (0.98) Symbol (3.31) Terminal box Waterproof gland (optional) X Y A B C Tag plate Nameplate (3.03) Description Grounding ring Excitation input Flow rate signal output H Grounding H1 * Terminal screw: M4 Electrode (7.89) Flange type Refer to note 1 Size 25 mm (1 inch) Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 5 Model no. Size mm (inches) J1 J2 J3 J4 J5 A1 JIS Flange rating 10 (3/8) Dimension 15 (1/2) Dimension 25 (1) Dimension Weight Weight Weight 10K 20K 30K A2 D1/D2 ANSI 10K 20K 10 mm flange 10 mm flange L 160 160 160 160 160 (kg) 5 5.2 6.2 4.9 5 L 200 200 200 200 200 (kg) 5.2 5.4 6.4 5.1 5.2 DIN 150 300 160 (6.3) 160 (6.3) 4.6 (10.1 lb) 5.1 (11.2 lb) 200 (7.87) D3/D4 200 (7.87) 4.8 (10.6 lb) 5.3 (11.7 lb) PN 10/16 PN 25/40 160 160 5.1 5.3 200 200 5.3 5.5 H 187 187 189 - - 188 (7.4) 186 (7.32) 182 182 H1 63 63 65 - - 54 (2.13) 62 (2.44) 58 58 (kg) 7.4 7.7 8.5 - - 7.3 7.6 - 13 - 6.6 (14.6 lb) 7.7 (17.0 lb) No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation Model MTG18B - Detector - Flange type size 40 mm (11/2 inch) to 100 mm (4 inches) (1.19 max.) (3.31) Blind plug (3.31) Waterproof gland (optional) Tag plate (1.85) (0.98) Terminal box Nameplate H2 Case Grounding ring Flange (7.87) Refer to Note 1 Electrode Symbol Description X Y A B C Excitation input Flow rate signal output Flange type Grounding Size 40 mm to 100 mm (11/2 inch to 4 inches) * Terminal screw: M4 Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 6 Size mm (inches) 40 (1.5) Model no. Flange rating Dimension Weight 50 (2) Dimension Weight 65 (2.5) Dimension Weight 80 (3) Dimension Weight 100 (4) Dimension Weight H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) H H1 H2 (kg) J1 10K 216 85 84 6.5 230 90 93 10.1 249 102 100 12.1 265 110 108 16.6 287.5 120 120.5 18.4 J2 JIS 20K 216 85 84 6.8 230 90 93 10.2 249 102 100 12.2 274 119 108 14.9 296.5 129 120.5 21.9 J3 A1 A2 ANSI 30K 227 96 84 9.2 236 96 93 11.9 263 116 100 13.9 279 124 108 18.6 304.5 137 120.5 26.8 150 208 (8.19) 77 (3.03) 84 (3.31) 6 (13.2 lb) 228 (8.98) 88 (3.46) 93 (3.66) 10.5 (23.1 lb) 250 (9.84) 103 (4.06) 100 (3.94) 12.5 (27.6 lb) 266 (10.47) 113 (4.45) 108 (4.25) 15.5 (34.2 lb) 298.5 (11.75) 131 (5.16) 120.5 (4.74) 23.3 (51.4 lb) - 14 - 300 225 (8.86) 94 (3.7) 84 (3.31) 8.3 (18.3 lb) 236 (9.29) 96 (3.78) 93 (3.66) 12 (26.5 lb) 258 (10.16) 111 (4.37) 100 (3.94) 14 (30.9 lb) 279 (10.98) 124 (4.88) 108 (4.25) 19.5 (43.0 lb) 312.5 (12.30) 145 (5.71) 120.5 (4.74) 32.4 (71.4 lb) D1/D2 D3/D4 DIN PN 10/16 PN 25/40 222 222 91 91 84 84 6.9 7.9 236 236 96 96 93 93 11.5 12 254 254 107 107 100 100 13.5 14 274 274 119 119 108 108 12.6 14.7 293.5 301.5 126 134 120.5 120.5 17.8 21.6 Yamatake Corporation No. SS2-MTG200-0100 (Rev.1) Model MTG18B - Detector - Flange type size 150 mm (6 inches) and 200 mm (8 inches) (3.31) Blind plug (1.19 max.) Waterproof gland (optional) (3.31) Terminal box Tag plate (1.85) (0.98) Nameplate H2 Case Grounding ring Flange Electrode L Refer to Note 1 Symbol X Y A B C Description Excitation input Flow rate signal output Flange type Size 150 mm and 200 mm (6 inches and 8 inches) Grounding * Terminal screw: M4 Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 7 Model no. Size mm (inches) 150 (6) Flange rating Dimension Weight 200 (8) J1 Dimension Weight J2 J3 A1 JIS A2 D1/D2 ANSI D3 D4 DIN 10K 20K 30K 150 300 L 300 300 300 300 (11.81) 300 (11.81) 300 300 300 H 382 396 407 381 (15) 403 (15.87) 385 393 393 H1 175 189 200 174 (6.85) 196 (7.72) 178 186 186 H2 160 160 160 160 (6.3) 160 (6.3) 160 160 160 (kg) 32.6 39.9 52.5 35.4 (78 lb) 54.4 (119.9 lb) 28.9 36.8 36.8 L 350 350 350 350 (13.78) 350 (13.78) 350 350 350 H 428 435 451 436 (17.17) 457 (17.99) 434 446 454 H1 196 203 219 204 (8.03) 225 (8.86) 202 214 222 H2 185 185 185 185 (7.28) 185(7.28) 185 185 185 (kg) 48 58 85.2 60 (132.3 lb) 89 (196.2 lb) 46.3 66.7 70.2 - 15 - PN 10/16 PN 25 PN 40 No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation Model MTG18B - Detector - Wafer type size 25 mm (1 inch) to 100 mm (4 inches) (1.19 max.) (3.31) (0.98) Terminal box Waterproof gland (optional) Tag plate (1.85) Blind plug (3.31) Nameplate Grounding ring Case D Electrode Refer to Note 1 Symbol X Y A B C Description Excitation input Flow rate signal output Wafer type Grounding Size 25 mm to 100 mm (1 inch to 4 inches) * Terminal screw: M4 Terminal Note 1 * When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension. * When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to the face-to-face dimension. Table 8 Flange rating 25 mm (1 inch) Face-to-face dimension code A L Dimension size Weight 40 mm (11/2 inch) A S 50 mm (2 inches) A S 65 mm (21/2 inches) A 80 mm (3 inches) A S 100 mm (4 inches) A S 94 (3.7) 80 (3.15) 98 (3.86) 86 (3.39) 104 (4.09) 96 (3.78) 106 (4.17) 130 (5.12) 120 (4.72) 150 (5.91) H 158 (6.22) 174.5 (6.87) 192 (7.56) 209 (8.23) 222 (8.74) 247 (9.72) H1 34 (1.34) 43.5 (1.71) 52 (2.05) 62 (2.44) 67 (2.64) 79.5 (3.13) H2 77 (3.03) 84 (3.31) 93 (3.66) 100 (3.94) 108 (4.25) 120.5 (4.74) D 68 (2.68) 87 (3.43) 104 (4.09) 124 (4.88) 134 (5.28) 159 (6.26) (kg) 2 (4.4 lb) 2 2.5 2.6 (4.4 lb) (5.5 lb) (5.7 lb) 3.2 (7.1 lb) 3.7 (8.2 lb) 4.6 5.3 6.4 7.4 (10.1 lb) (11.7 lb) (14.1 lb) (16.3 lb) Savemation Saving through Automation 2-12-19 Shibuya Shibuya-ku, Tokyo 150-8316 Japan Tel : 81-3-3486-2310 Fax : 81-3-3486-2593 - 16 This has been printed on recycled paper. http://www.yamatake.com/