Matrix Weller brings to the market an extended generation of versatile soldering/desoldering, SMD rework stations and tools. Performance has been increased with soldering irons and desoldering irons up to 150 W. Choose between Weller stations with powerful in-built pumps, or smaller units without pumps that allow you to connect to your own factory line. All Weller stations easily connect to a variety of new and existing Weller tools and accessories to provide even greater flexibility. The matrix below makes selection easy, and puts you firmly in control of all your workbench needs. WMD 3 WMD 1 WAD 101 WDD 81V WDD 161V HAP 1 HOT AIR PENCIL (KH 20 Support for HAP 1) DSX 80 DESOLDERING IRON (AK 20 Support for DSX 80) DS 80 UNC* DESOLDERING IRON (AK 20 Support for DS 80 UNC) DSX V80 DESOLDERING IRON (AK V Support for DSX V80) DS V80 UNC* DESOLDERING IRON (AK V Support for DS V80 UNC) DS VT 80 DESOLDERING IRON (AK V Support for DS VT 80) LR 21 SOLDERING PENCIL (KH 20 Support for LR 21) LR 82 SOLDERING IRON (KH 27 Support for LR 82) WSP 80 MICRO SOLDERING PENCIL (WPH 80 Support for WSP 80) WSP 150 SOLDERING IRON (KH 27 Support for WSP 150) MLR 21 MICRO SOLDERING PENCIL (KH 15 Support for MLR 21) MPR 80 ANTISTATIC PERITRONIC (KH 25P Support for MPR 80) WMP MICRO SOLDERING PENCIL (WPHM support for WMP) WST 20 THERMAL WIRE STRIPPER (support included) WHP 80 PREHEATING PLATE WTA 50 TWEEZER (AK 51 Support for WTA 50) WSB 80 SOLDER BATH WCB 1 CALIBRATION UNIT WCB 2 CALIBRATION UNIT *UNC. For use with nozzles with an inch thread. 2 Weller Multi-Digital Rework Station WMD 3 (With In-Built Pump) Three connectors for variable combinations of hot air pencil, desoldering iron, soldering iron or other variable combinations. Socket for potential balance. Multi-digital display shows the set and read temperature of each tool and air volume. Two connections for two optional foot switches. Microprocessor controlled channel. Continuously adjustable for soldering iron, desoldering iron and hot air pencil or other connectable tools. Antistatic coating on housing meets ESD safety specifications. Pilot light showing heating pulses. Manometer for vacuum control. LED indicates channel in display. Mains switch. Connector for hot air pencil with filter cartridge. Channel selector for temperature and air volume. Timer/set back. Lock-out key for set function parameters of each channel. Vacuum connector with filter cartridge. WELLER WMD 3 Weller WMD 3 state-of-the-art technology simultaneously provides multi-digital control of working temperatures when reworking conventional ICs and SMDs. A soldering iron, desoldering iron and hot air pencil can all be operated simultaneously because of the WMD 3's in-built micro- processor that infinitely controls each tool's set temperature and airflow. The display visually monitors each chosen working temperature and times preset hot gas pencil operations. T E C H N I C A L D ATA DIMENSIONS: 240 x 270 x 105 mm (W x D x H) LINE VOLTAGE: 230 V, 50 Hz POWER INPUT: 310 W PROTECTION CLASS: 1 and 3 FUSE: T 1,5 A located at the power entry module CONTROLLING TOLERANCE: Soldering/Desoldering iron 2 % of the final value Hot air pencil 30 C TEMPERATURE CONTROL WITH ZERO VOLTAGE CROSS SWITCHING: Soldering/Desoldering iron continuously 50 C - 450 C (WSP 150 150 C - 550 C) Hot air pencil continuously 50 C - 550 C PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min Hot Air: max. 10 l/min POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit 3 Weller Multi-Digital Hot Air Station WMD 1A (With In-Built Pump) Antistatic coating on housing meets ESD safety specifications. Socket for potential balance. Multi-digital display shows the set and read temperature of each tool and air volume. Temperature and hot air control. Manometer for vacuum control. Seven-pin connector for all desoldering, soldering and accessory tools. Holder KH27 for HAP 1 ho tair pencil. Pilot light showing heating pulses. Mains switch. Vacuum connector and filter cartridge. Air connector for hot air pencil. HAP 1 Hot air pencil. Hot air nozzles. Different interchangeable types available. WELLER WMD 1A The multi application ability of this station makes it ideal for use in situations where the maximum amount of flexibility is required. The station has an in built pump to provide the air movement for the hot air pencil and the vacuum for the desoldering tool and can be used to rework both surface mounted and through hole components. The WMD 1S control unit is the base and incorporates a micro processor controlled system to regulate the solder processes. The processor can also identify which tool is being used and calibrate the output automatically without the need for manual adjustment. By use of the WCB1 and WCB 2 control boxes, additional functions can be programmed into the base unit such as, temperature lock, set back time, temperature offset, deg C / deg F, factory setting reset. T E C H N I C A L D ATA DIMENSIONS: 240 x 270 x 105 mm (W x D x H) LINE VOLTAGE: 230 V, 50 Hz POWER INPUT: 175 W SAFETY CLASS: 1 and 3 FUSE: Glass tube fuse O 5 x 20; T 800 mA located at the power entry module CONTROLLING TOLERANCE: Soldering/Desoldering iron 2 % of the final value Hot air pencil 30 C TEMPERATURE CONTROL WITH ZERO VOLTAGE CROSS SWITCHING: 4 Hot air pencil continuously 50 C - 550 C PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min Hot air: max. 10 l/min POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit Weller Multi-Digital Desoldering Station WMD 1D (With In-Built Pump) Antistatic coating on housing meets ESD specifications. Multi-digital display shows the set and read temperature of each tool and air volume. Socket for potential balance. Temperature and hot air control. Pilot light showing heating pulses. Holder AK 20 for DSX 80 desoldering iron. Seven-pin connector for all desoldering, soldering and accessory tools. Manometer for vacuum control. Vacuum connector and filter cartridge. Mains switch. DSX 80, 24V Desoldering iron with 80W heating element. 'Longlife' tiplets. Different interchangeable types available. WELLER WMD 1D The multi application ability of this station makes it ideal for use in situations where the maximum amount of flexibility is required. The station has an in built pump to provide the vacuum for the desoldering tool and can be used to rework both surface mounted and through hole components. The WMD 1S control unit is the base and incorporates a micro processor controlled system to regulate the desolder processes. The processor can also identify which tool is being used and calibrate the output automatically without the need for manual adjustment. By use of the WCB 1 and WCB 2 control boxes, additional functions can be programmed into the base unit such as, temperature lock, set back time, temperature offset, deg C / deg F, factory setting reset. T E C H N I C A L D ATA DIMENSIONS: 240 x 270 x 105 mm (W x D x H) LINE VOLTAGE: 230 V, 50 Hz POWER INPUT: 175 W PROTECTION CLASS: 1 and 3 FUSE: Glass tube fuse O 5 x 20; T 800 mA located at the power entry module CONTROLLING TOLERANCE: Soldering/Desoldering iron 2 % of the final value Hot air pencil 30 C TEMPERATURE CONTROL WITH ZERO VOLTAGE CROSS SWITCHING: Soldering/Desoldering iron continuously 50 C - 450 C (WSP 150 150 C - 550 C) PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min Hot air: max. 10 l/min POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit 5 Weller Multi-Functional, Digital Desoldering Station WDD 161V Multi-digital display shows the set and read temperature of DSX 80 or other connected tool. Microprocessor controlled channel. Automatically recognizes the DSX 80 and other connected tools and sets the appropriate control parameters. Holder AK20 for DSX 80 desoldering iron. Holder WPH 80 for soldering pencil WSP 80. Antistatic coating on housing meets ESD safety specifications Mains switch. LED showing heating pulses. DSX 80 Desoldering iron. Seven-pin connector for connecting the DSX and other soldering tools. Connector for potential balance Finger switch to control vacuum. Connector for vacuum "Longlife"tiplets. Different interchangeable types available. WSP 80 soldering pencil. Weller WDD 161V The WDD 161V rework station is a dual output unit supplied with soldering and desoldering tools. It features a micro processor controlled system which allows independent temperature control of both tools. The station will automatically recognize the tool in use and calibrate itself for that tool. Vacuum for the desoldering tool is generated by an internal venturi driven from an external compressed air source. The selected operating temperatures are displayed on a digital display switchable between tools. By use of the WCB 1 and WCB 2 control boxes, additional functions can be programmed into the base unit such as, temperature lock, set back time, temperature offset, deg C / deg F, factory setting reset. T E C H N I C A L D ATA 6 DIMENSIONS: 166 x 115 x 101 mm (W x D x H) POWER INPUT: 165 W TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50 C - 450 C COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry compressed air COMPRESSED AIR CONVERTER: Air consumption 35 l/min Vacuum 55 KPA (8 psi) COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter PROTECTION CLASS: 1 (control unit), 3 (soldering tool) Weller Multi-Functional, Digital Desoldering Station WDD 81V Microprocessor controlled channel. Automatically recognizes the DSX 80 and other connected tools and sets the appropriate control parameters. Multi-digital display shows the set and read temperature of the DSX 80 or other connected tool. Holder AK20 for DSX 80 desoldering iron. Antistatic coating on housing meets ESD safety specifications Seven-pin connector for connecting the DSX and other soldering tools. Mains switch. Pilot light showing heating pulses. Connector for potential balance Connector for vacuum. DSX 80 Desoldering iron. Finger switch to control vacuum. "Longlife"tiplets. Different interchangeable types available. WELLER WDD 81V The Weller WDD 81V Desoldering station features digital process control for exact temperature set. The in-built microprocessor circuitry automatically recognizes all Weller soldering irons and provides the optimal settings of the connected tool. The station comes with the DSX 80 Desoldering iron. A range of desoldering suction tiplets enables solder to be removed from a wide variety of solder joints. The Weller CSF rework heads can also be interchanged to provide total flexibility in the rework of most Flat Packs. An internal maintenance-free compressed air converter provides the vacuum for the desoldering iron. The WDD 81V requires a compressed air supply. The Weller WCB 1 or WCB 2 Calibration unit can be connected to the WDD 81V to further enhance programme setting. PC interface is possible with the WCB 2 only. T E C H N I C A L D ATA DIMENSIONS: 166 x 115 x 101 mm (W x D x H) POWER INPUT: 95 W TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50 C - 450 C COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry compressed air COMPRESSED AIR CONVERTER: Air consumption 35 l/min Vacuum 55 KPA (8 psi) COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter PROTECTION CLASS: 1 (control unit), 3 (soldering tool) 7 Weller Multi-Functional, Digital Desoldering Station WDD 81VIL Microprocessor controlled channel. Automatically recognizes the DSX V80 and other connected tools and sets the appropriate control parameters. Multi-digital display shows the set and read temperature of the DSX V80 or other connected tool. Antistatic coating on housing meets ESD safety specifications Holder AK V for DSX V80 desoldering iron. Mains switch. Seven-pin connector for connecting the DSX V80 and other soldering tools. Connector for potential balance Pilot light showing heating pulses. Connector for vacuum. DSX V80 Desoldering iron. Finger switch to control vacuum. "Longlife"tiplets. Different interchangeable types available. WELLER WDD 81VIL The Weller WDD 81VIL Inline desoldering station features digital process control for exact temperature set. The in-built microprocessor circuitry automatically recognizes all Weller soldering irons and provides the optimal settings of the connected tool. The station comes with the DSX V80 Inline desoldering iron. A range of desoldering suction tiplets enables solder to be removed from a wide variety of solder joints. The Weller CSF rework heads can also be interchanged to provide total flexibility in the rework of most Flat Packs. An internal maintenance-free compressed air converter provides the vacuum for the inline desoldering iron. The WDD 81VIL requires a compressed air supply. The Weller WCB 1 or WCB 2 Calibration unit can be connected to the WDD 81VIL to further enhance programme setting. PC interface is possible with the WCB 2 only. T E C H N I C A L D ATA 8 DIMENSIONS: 166 x 115 x 101 mm (W x D x H) POWER INPUT: 95 W TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50 C - 450 C COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry compressed air COMPRESSED AIR CONVERTER: Air consumption 35 l/min Vacuum 55 KPA (8 psi) COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter PROTECTION CLASS: 1 (control unit), 3 (soldering tool) Weller Multi-Functional, Digital Hot Air Station WAD 101 Pilot light showing heating pulses Multi-digital display sets and reads temperature of the selected tool Microprocessor controlled channel. Automatically recognizes the HAP 1 and other connected tools and sets the appropriate control parameters Holder KH27 for HAP 1 ho tair pencil Antistatic coating on housing meets ESD specifications Air volume control Hot air nozzles. Different interchangeable types available Mains switch Connector for hot air Seven-pin connector for connecting the HAP 1 and other soldering tools HAP 1 Hot air pencil Connector for potential balance Finger switch to control air manually WELLER WAD 101 The Weller WAD 101 Hot air station features digital process control for accurate temperature set. The in-built microprocessor circuitry automatically recognizes all Weller soldering irons and provides the optimal settings of the connected tools as well as the HAP 1 that comes as standard with the station. A wide range of nozzles and tools makes the WAD 101 ideal in many soldering and desoldering applications of surface mount devices. The WAD 101 requires a compressed air supply with oil-free, dry air or nitrogen (N2) where the airflow is manually controlled. The Weller WCB 1 or WCB 2 Calibration unit can be connected to the WAD 101 to further enhance programme setting. PC interface is possible with the WCB 2 only. T E C H N I C A L D ATA DIMENSIONS: 166 x 134 x 101 mm (W x D x H) POWER INPUT: 105 W TEMPERATURE CONTROL: Hot air pencil 50 C - 550 C FLOW RATE: Approx. 0-10 l/min COMPRESSED AIR: Inlet pressure 400 KPA (58 psi) oil-free, dry compressed air or nitrogen (N2) COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0,24") external diameter PROTECTION CLASS: 1 (control unit), 3 (soldering tool) 9 Weller Flexibility. Refer to the matrix to make your choice of connecting tools for the WMD 3, WMD 1A + D, WDD 161V, WDD 81V + VIL and WAD 101 (see matrix page 2). HAP 1 5 33 114 99 HAP 1 Hot air pencil The HAP 1, 100W/24V, provides a directional hot airflow that is adjustable and static-free. Electronically temperature controlled from 50C to 550C. Different nozzles available as accessories. Finger switch controls speed adjustable pump. Hot air pencil set, consisting of HAP 1 with finger switch, KH 27 Support for pencil, nozzle 1,2 and 3,0 mm, key and nutdriver for nozzle changing. DSX 80 (DS 80 UNC*) 5 33 138 99 (5 13 191 99) DSX 80 (DS 80 UNC*) Desoldering iron and service kit An 80W/24V desoldering iron for electronics rework. Electronically temperature controlled. Micro-finger switch controls quick-start, fast action vacuum pump. Different interchangeable tiplets, plus several CSF devices are available as accessories. DS 80 (DS 80 UNC*) set, consisting of DS 80 (DS 80 UNC*) Desoldering iron AK 20 Support, cleaning tool, glass collector, two desoldering nozzles, gasbet, anti-bloc paste, filter. LR 21 5 33 112 99 LR 21 Antistatic soldering pencil Electronically temperature controlled 50W/24V soldering pencil. LR 21 set, consisting of LR 21 Antistatic soldering pencil, KH 20 Support for pencil. LR 82 5 33 113 99 LR 82 Antistatic soldering iron An 80W/24V soldering iron for high mass soldering. Dual sensor, electronically temperature controlled. LR 82 set, consisting of LR 82 Antistatic soldering iron, KH 27 Support for iron. WSP 80 5 29 161 99 DSX V80 (DS V80 UNC*) 5 33 137 99 (5 33 129 99) DSX V80 (DS V80 UNC*) Desoldering iron Connectable to all 80W desoldering stations. Handle utilizes the tin collector to hold the extracted solder. Easy to clean by use of the bayonet fitting. DSX V80 set, consisting of DSX V80 Desoldering iron, AKV Support for iron. WSP 80 Micro soldering pencil A micro soldering pencil, 80W/24V. This soldering pencil can be universally used in all situations from extremely delicate soldering to those where there is a greater temperature requirement. WSP 80 set, consisting of WSP 80 Micro soldering pencil with WPH 80 Support. WSP 150 5 33 135 99 DS VT80 5 33 134 99 DS VT80 Desoldering iron The model DS VT80 heats up Weller CSF desoldering heads and is equipped with a spring-loaded vacuum pipette, which makes this tool ideal for rework of larger SMD components. DS VT80 set, consisting of DS VT80 Desoldering iron, AK V Support for iron. 10 *UNC. For use with nozzles with an inch thread. WSP 150 Soldering iron The WSP 150, 150W/24V, soldering iron was specially developed for soldering tasks with extremely high heat requirements. The 150 W heater power combined with optimal transfer of heat to the soldering iron bit guarantee the high performance capability of the soldering iron. WSP 150 set, consisting of WSP 150 Soldering iron, KH 27 Support for iron. MLR 21 5 33 111 99 MLR 21 Micro soldering pencil A micro soldering pencil, 25W/24V with antistatic cord, suitable for miniature soldering work. Electronically temperature controlled. MLR 21 set, consisting of MLR 21 Micro soldering pencil, KH 15 Support for pencil. WST 20 5 25 030 99 WST 20 Thermal wire stripper with support The WST 20, 50W/24V, copes with all known thermoelastic plastics. Adjustable for a stripping length up to 30 mm. Additional blades available for stripping flat cables and shrinking. WTA 50 5 33 133 99 MPR 80 5 33 131 99 MPR 80 Antistatic Peritronic soldering pencil An 80W Antistatic Peritronic soldering pencil that gives all-round vision when making intricate connections. Antistatic cord and handle. Electronically temperature controlled. Consists of MPR 80 Antistatic and KH 25P Support. WTA 50 Tweezer This tweezer is used to desolder SMD components. The tweezer has two moveable heating elements. WTA 50 set, consisting of WTA 50 Tweezer, AK 51 Support for Tweezer. WSB 80 5 27 040 99 WMP 5 33 155 99 WMP Micro soldering pencil The 65W micro pencil is up to the task with superior performance for both heat-up and thermal efficiency. Suitable to handle all micro components and fine pitch tasks. The WMP provides an extremely short tip-to-grip distance. The heater is integrated into the handle. When the tip wear out the heating element goes on. WMP set consisting of WMP micro soldering pencil and WPHM holder for WMP. WHP 80 5 27 028 99 WHP 80 (80W/24V) Preheating plate With a heating surface of 80 x 50 mm, they preheat IC boards prior to micro rework. WSB 80 Solder bath The WSB 80 is a very useful rework preparation tool. The solder bath is temperature controlled continuously from 50C to 450C via an existing 80W power source. The solder bath can be used to tin wire ends and clean leads of all extraneous solder particles in preparation for reworking. WCB 1 5 31 181 99 WCB 2 5 31 180 99 WCB 1, WCB 2 Calibration units The intelligence of the digital Weller units can be further enhanced by being programmed by either the WCB 1 or WCB 2 Calibration unit. Both the WCB 1 and the WCB 2 feature temperature lockout and off-set capabilities up to + 40C. The WCB 2 has the added ability to PC interface (RS 232) and a thermoelement type K and measuring tip. 11 CSF Accessories for DS 80 (DS 80 UNC),DSX 80, DS V80 (DS V80 UNC), DSX V80 and DS VT80 for SMD's chip desoldering tiplets for flat packs DS 80 (DS 80 UNC),DSX 80 DS V80 (DS V80 UNC), DSX V80 DS VT80 CSF-Q x1 (mm) x y1 (mm) CSF-Head Order No. x1 > x + 0,3 y1 > y + 0,3 12,0 12,0 12,7 17,0 17,0 19,6 Adaptor for DS 80 UNC, DS V80 UNC Adaptor for DS 80, DS V80 Adaptor for DS VT80 Adaptor for DSX80, DSX V80 Rubber insert (spare) Adaptor O x x x x x x 12,0 14,5 12,7 17,0 23,0 19,6 5 87 417 33 5 87 417 34 5 87 417 35 5 87 417 36 5 87 417 37 5 87 417 38 6 6 6 11 16 11 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 89 5 87 417 90 5 87 417 89 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 16 5 87 417 17 5 87 417 16 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 85 5 87 417 86 5 87 417 85 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 04 5 87 418 05 5 87 418 04 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 98 5 87 137 98 5 87 137 98 x x x x x 12,7 17,8 20,4 25,4 30,4 5 87 417 39 5 87 417 40 5 87 417 41 5 87 417 42 5 87 417 43 6 11 16 16 16 5 87 417 88 5 87 417 89 5 87 417 90 5 87 417 90 5 87 417 90 5 87 417 15 5 87 417 16 5 87 417 17 5 87 417 17 5 87 417 17 5 87 417 84 5 87 417 85 5 87 417 86 5 87 417 86 5 87 417 86 5 87 418 03 5 87 418 04 5 87 418 05 5 87 418 05 5 87 418 05 5 87 137 99 5 87 137 98 5 87 137 98 5 87 137 98 5 87 137 98 x x x x x x x x x x 10,0 10,5 10,0 13,0 10,0 18,0 16,0 16,0 18,0 26,5 5 87 417 23 5 87 417 24 5 87 417 25 5 87 417 26 5 87 417 27 5 87 417 28 5 87 417 29 5 87 417 30 5 87 417 31 5 87 417 32 6 6 6 6 6 6 6 6 6 11 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 88 5 87 417 89 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 15 5 87 417 16 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 84 5 87 417 85 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 03 5 87 418 04 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 99 5 87 137 98 5 87 417 44 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99 CSF-Ql 12,7 17,8 20,4 25,4 30,4 CSF-D 5,5 5,8 6,7 9,3 9,4 9,8 10,0 10,5 10,7 11,0 CSF-Dl SOJ-Case 9,0 12 x 18,0 Accessories For easier rework and repair, Weller has a large range of desoldering nozzles and soldering tips. Threadless nozzles for desoldering iron DSX 80 und DSX V80 The new X series nozzle feature a threadless fixture system whereby the nozzle is inserted into the head and locked into place by apllying a 1/4 turn. This feature allows the nozzles to be quickly and easily exchanged and also improves the rate of thermal transfer from the head to the nozzle. DSX 80 DSX V80 Nozzles for desoldering iron DSX 80 and DSX V80: Model mm mm mm Order No. DX110 Description Nozzle 1,9 0,7 23 5 13 140 00 DX111 Nozzle 2,5 0,7 23 5 13 141 00 DX112 Nozzle 2,3 1,0 23 5 13 142 00 DX113 Nozzle 2,5 1,2 23 5 13 143 00 DX113HM Nozzle 2,5 1,2 23 5 13 150 00 with improved thermal transfer DX114 Nozzle 3,3 1,8 23 5 13 144 00 DX115 Nozzle 1,9 0,7 23 5 13 145 00 DX116 Nozzle 2,7 1,2 29 5 13 146 00 DX117 Nozzle 2,9 1,5 23 5 13 147 00 DX118 Nozzle 1.5 0.7 23 5 13 148 00 DX119 Needle Tiplet 1,1 0,7 31 5 13 151 00 for removal of solder bridges in connection with hot air pencil DX120 Nozzle 2,5 1,1 22 5 13 152 00 21.5 5 13 153 99 without inside tube, for cleaning of SMD pads Measuring Nozzle 3,3 0,55 for temperature measurement with thermocouple 0.5 Conus insert for cleaning tool 5 87 067 94 Nozzle Set 5 13 790 99 DX 110-DX115 13 Hot Air Nozzles for hot air pencil HAP 1 Description Dimensions (mm) Type Order No. Nozzle 18,0 x 18,0 Q10 5 87 277 85 Nozzle 12,5 x 15,0 Q08 5 87 277 83 Nozzle 15,0 x 10,0 Q06 5 87 277 80 Nozzle 6,0 x 9,0 Q04 5 87 277 78 Nozzle 6,0 x 6,5 Q02 5 87 277 77 Nozzle 10,0 x 18,0 D10 5 87 277 84 Nozzle 15,0 x 10,0 D08 5 87 277 81 Nozzle 10,0 x 13,0 D06 5 87 277 82 Nozzle 10,5 x 10,5 D04 5 87 277 79 R01 5 87 278 08 Measuring nozzle 14 Hot Air Nozzles for hot air pencil HAP 1 Description Dimensions (mm) Type Order No. Flat nozzle 12,0 x 1,5 F06 5 87 277 72 Flat nozzle 10,5 x 1,5 F04 5 87 277 73 Flat nozzle 8,0 x 1,5 F02 5 87 277 74 Straight O 2,0 R10 5 87 277 87 Bent O 2,0 R08 5 87 277 86 Nozzle O 3,0 R06 5 87 278 22 Nozzle O 1,2 R04 5 87 278 21 Nozzle O 0,8 R02 5 87 278 23 Dual nozzle O 1,5 x 10,0 FD4 5 87 277 75 Dual nozzle O 1,5 x 8,0 FD2 5 87 277 76 15 Soldering Tips for soldering iron LR 82 Description Width A Thickness B Type Order No. 3,2 mm 1,0 mm HT 1 5 44 260 99 5,2 mm 1,2 mm HT 2 5 44 261 99 7,0 mm 1,2 mm HT 3 5 44 262 99 3,2 mm 1,0 mm HT C 5 44 267 99 4,6 mm 1,0 mm HT D 5 44 268 99 5,6 mm 1,0 mm HT E 5 44 269 99 2,4 mm 8,3 mm HT BS 5 44 264 99 3,2 mm 8,3 mm HT CS 5 44 265 99 5,0 mm 8,3 mm HT DS 5 44 266 99 A Chisel Chisel B A B Chisel A B Screwdriver A B Screwdriver A B Screwdriver A B Round tip B A Round tip B A Round tip B A Calibration tip 16 - - - 5 44 263 99 Soldering Tips for soldering pencil LR 21 Description Width Type Order No. for regular solder Order No. for HPB solder Screwdriver tip 0,8 mm 1,6 mm 2,4 mm 3,2 mm 4,6 mm 5,6 mm ET H ET A ET B ET C ET D ET E 5 41 000 99 5 41 001 99 5 41 002 99 5 41 003 99 5 41 004 99 5 41 005 99 5 41 000 74 5 41 001 73 5 41 002 71 5 41 003 72 - Long screwdriver tip 1,2 mm 2,0 mm 3,2 mm ET K ET L ET M 5 41 006 99 5 41 007 99 5 41 008 99 5 41 007 73 - Round tip, blunt 0,8 mm 2,4 mm 3,2 mm 5,0 mm 0,8 mm 1,2 mm 2,4 mm 3,2 mm 0,8 mm 0,4 mm ET P ET BS ET CS ET DS ET AA ET F ET BB ET CC ET O ET S 5 41 038 99 5 41 009 99 5 41 010 99 5 41 011 99 5 41 031 99 5 41 012 99 5 41 055 99 5 41 013 99 5 41 014 99 5 41 017 99 - Screwdriver tip 1,6 mm ET R 5 41 015 99 - Flat tip, slightly bent, one side wettable only 3,2 mm ET MX 5 41 016 99 - 2,5 x 1,5 mm 3,8 x 1,5 mm ET SMD ET SMD 5 41 039 99 5 41 040 99 - Sloped round tip Conical long tip Chip soldering/desoldering tip Soldering tip for J-Leads - ET JL 5 41 018 99 - Soldering tip for Gullwings - ET GW 5 41 045 99 - ET Calibration nozzle - - 5 24 750 99 - 17 Soldering Tips for soldering pencil MLR 21 Description Width Type Order No. Micropoint 0,25 mm MT 1 5 44 101 99 Micropoint 0,2 mm 0,25 mm MT 1SL MT 1S 5 44 115 99 5 44 105 99 Chisel 1,6 mm MT 6 5 44 106 99 Round tip 1,2 mm MT 4 5 44 104 99 Screwdriver 0,8 mm 1,6 mm 2,4 mm MT H MT A MT B 5 44 112 99 5 44 110 99 5 44 111 99 Screwdriver bent 0,8 mm MT HX* 5 44 113 99 Soldering tip for J-Lead - Soldering tip for Gullwings O 2,0 mm O 4,0 mm Calibration tip 18 *only with barrel nut 5 87 207 01 - MT JL 5 44 118 99 MT GW MT GW 5 44 119 99 5 44 120 99 - 5 44 114 99 Soldering Tips For micro soldering pencil WMP Description Width A Thickness B Length C Type / Order No. Chisel tip 0,8 mm 1,2 mm 1,6 mm 1,6 mm 2,4 mm 3,2 mm 4,0 mm 0,4 mm 0,4 mm 0,4 mm 0,4 mm 0,8 mm 0,8 mm 0,8 mm 8,4 mm 8,4 mm 8,4 mm 9,5 mm 7,4 mm 7,8 mm 7,8 mm NTH NTK NTA NT6 NTB NTC NTD Chisel tip, bent Round tip, bent Round tip 0,4 mm 1,6 mm 0,25 mm 1,6 mm 0,8 mm - 8,2 mm 8,6 mm 7,4 mm NTAX NT1X NT1 Round tip small 0,25 mm - 8,5 mm NT1S Round tip, sloped 45 1,2 mm - 9,9 mm NT4 Gull Wing 2,0 mm 3,0 mm 13,4 mm NTGW - - NTMS NT Measuring tip - Description B Blade C A Slot B A C Tunnel B A C Quad B A C Width A Thickness B 10,4 mm 16,8 mm 20,8 mm 1,8 mm 1,5 mm 2,5 mm 2,3 mm 4,6 mm 10,4 mm 11,5 mm 13,2 mm 15,8 mm 18,3 mm 18,8 mm 2,7 mm 10,4 mm 12,7 mm 13,7 mm 19,1 mm 23,2 mm 24,5 mm 29,6 mm 0,6 mm 0,6 mm 0,6 mm 9,4 mm 2,3 mm 1,7 mm 4,5 mm 5,1 mm 5,1 mm 6,9 mm 9,5 mm 9,5 mm 9,5 mm 9,0 mm 7,7 mm 10,4 mm 12,7 mm 8,6 mm 19,1 mm 17,3 mm 24,5 mm 29,6 mm Length C Component Type 7,1 mm Any (for pad clean-up) 7,1 mm Any (for pad clean-up) 7,1 mm Any (for pad clean-up) 1,8 mm Chip 1,8 mm Chip 1,4 mm Chip 1,8 mm Chip 2,3 mm DIP 2,3 mm DIP 2,3 mm DIP 3,2 mm DIP 3,2 mm DIP 3,2 mm DIP 3,2 mm DIP 3,8 mm PLCC & QFP 3,8 mm PLCC & QFP 3,8 mm PLCC & QFP 3,8 mm PLCC & QFP 5,6 mm PLCC & QFP 3,8 mm PLCC & QFP 5,6 mm PLCC & QFP 5,6 mm PLCC & QFP Type/ Order No. NTSMT01 NTSMT02 NTSMT03 NTSMT04 NTSMT05 NTSMT06 NTSMT07 NTSMT08 NTSMT09 NTSMT10 NTSMT11 NTSMT12 NTSMT13 NTSMT14 NTSMT15 NTSMT16 NTSMT17 NTSMT18 NTSMT19 NTSMT20 NTSMT21 NTSMT22 19 Soldering Tips for WSP 80, WSP 80 FE and MPR 80 WSP 80 (FE) MPR 80 20 Description Width A Round tip Thickness B Type Order No. Order No. 0,25 mm LT 1 5 44 435 99 - - Long tip, conical 0,2 mm LT 1L 5 44 423 99 - - Round tip 0,2 mm LT 1S 5 44 436 99 - - Round tip 1,6 mm LT AS 5 44 404 99 - - Round tip 3,2 mm LT CS 5 44 411 99 - - Chisel tip 0,8 mm 0,8 mm Round tip, spade 1,2 mm Chisel tip 1,2 mm Chisel tip 1,6 mm 0,4 mm 0,4 mm regular solder HPB solder Order No. lead free solder LT H 5 44 437 99 LT H HPB 5 44 430 99 - LT F 5 44 408 99 - - 0,4 mm LT K 5 44 438 99 - - 1,6 mm 1,6 mm 0,7 mm 0,7 mm LT A 5 44 440 99 LT A HPB 5 44 431 99 - Long chisel tip 2,0 mm 1,0 mm LT L - Chisel tip 2,4 mm 2,4 mm 2,4 mm 0,8 mm 0,8 mm 0,8 mm LT B 5 44 405 99 LT B HPB 5 44 432 99 LT B LL 5 44 446 99 Chisel tip 3,2 mm 3,2 mm 0,8 mm 0,8 mm LT C 5 44 407 99 LT C LL - 5 44 447 99 Long chisel tip 3,2 mm 1,2 mm LT M 5 44 415 99 - - Chisel tip 4,6 mm 4,6 mm 0,8 mm 0,8 mm LT D 5 44 409 99 LT D LL - 5 44 448 99 Round tip, spade 1,2 mm LT 4 - - 5 44 414 99 5 44 439 99 - Soldering Tips for WSP 80, WSP 80 FE, MPR 80 WSP 80 (FE) MPR 80 Description Width A Thickness B Type Order No. 3, 2 mm LT GW 5 44 410 99 regular solder Tip for Gullwings 2,4 mm Long tip, conical 0,4 mm LT S 5 44 406 99 Long tip, bent 0,2 mm LT 1LX 5 44 424 99 Chisel tip, bent 0,8 mm 1,6 mm 2,4 mm 0,4 mm 0,7 mm 0,8 mm LT HX LT ALX LT BX 5 44 420 99 5 44 443 99 5 44 442 99 Chisel tip, bent 1,2 mm 0,4 mm LT 4X 5 44 428 99 Chisel tip, bent 1,6 mm 0,8 mm LT AX 5 44 427 99 Round tip, bent 2,0 mm 0,4 mm LT 1X 5 44 425 99 Round tip, bent 2,0 mm 0,4 mm LT 1SLX 5 44 426 99 Round tip, spade 2,4 mm 3,2 mm 4,0 mm 6,0 mm LT BB LT CC 5 44 444 99 5 44 445 99 LT Desoldering tip 10,5 mm 0,6 mm LT Adaptor for SMD tips 13,5 mm LT Measuring tip 5 44 429 99 5 44 417 99 5 44 446 00 21 Soldering Tips WSP 150 WTA 50 Description For soldering iron WSP 150 Width A Thickness B Type Order No. Chisel tip 3,2 mm 1,2 mm LHT C 5 44 455 99 Chisel tip 4,7 mm 1,8 mm LHT D 5 44 452 99 Chisel tip 6,7 mm 1,8 mm LHT E 5 44 451 99 Chisel tip 9,3 mm 1,8 mm LHT F 5 44 450 99 Chisel tip, bent 5 mm 7 mm 10 mm 2 mm 2 mm 2 mm LHT DX LHT EX LHT FX 5 44 462 99 5 44 461 99 5 44 460 99 LHT Calibration tip - - - 5 44 453 99 Tip set 0,5 mm 0,5 mm WTA 1S 5 44 145 99 Tip Set 1,0 mm 0,5 mm WTA 1 5 44 141 99 Tip set 3,0 mm 0,5 mm WTA 2 5 44 146 99 Tip set 6,0 mm 0,5 mm WTA 3 5 44 147 99 Tip set 12,5 mm 0,5 mm WTA 4 5 44 143 99 Tip set 18,5 mm 0,5 mm WTA 5 5 44 144 99 Tip set vertical use 1,0 mm 0,5 mm WTA 11 5 44152 99 Tip set vertical use 3,0 mm 0,5 mm WTA 12 5 44 153 99 For WT 50 and WTA 50 tweezer 22 Additional Support and Holders 5 15 010 99 AK 1 Support for DSX 80 (DS 80 UNC) Desoldering iron, HAP 1 Hot air pencil, LR 21 and LR 82 Antistatic soldering pencils 5 15 012 99 AK 21 Support for MPR 80 Peritronic soldering pencil 5 15 042 99 AK 51 Support for WTA 50 Tweezer 5 15 020 99 KH 20 Support for LR 21 Antistatic soldering pencil and HAP 1 Hot air pencil 5 15 030 99 AK 20 Support for DSX 80 (DS 80 UNC) Desoldering iron and HAP 1 Hot air pencil 5 15 140 99 WPHM WPHM support for WMP micro soldering pencil WPH 80 Support for WSP 80 Micro soldering pencil 5 15 038 99 AK V Support for DS VT80 and DSX V80 (DS V80 UNC) Desoldering iron 5 15 033 99 KH 25P Support for MPR 80 Peritronic soldering pencil 5 15 019 99 KH 15 Support for MLR 21 Micro soldering pencil 5 15 027 99 KH 27 Support for LR 82 Soldering iron, HAP 1 and WSP 150 23 Consists of: Power unit Order No.: Consists of: Power unit WMD 1S 5 33 026 99 (UK: 5 33 023 99) Hot air pencil HAP 1 Holder KH 27 Nozzle R 04 Nozzle R 06 Cleaning set Order No.: WDD 161V Consists of: Power unit PUDD 161V Desoldering iron DSX 80 Soldering pencil WSP 80 Holder AK 20 Holder WPH 80 Nozzle DX 112 Nozzle DX 113 Cleaning set Replacement glass tube Order No.: WMD 1D WMD 1A WMD 3 5 33 286 99 (UK: 5 33 283 99) 5 27 115 99 5 15 027 99 5 87 278 21 5 87 278 22 5 13 500 99 5 33 306 99 (UK: 5 33 303 99) Consists of: Power unit WMD 1S Order No.: Consists of: Power unit PUDD 81V Desoldering iron DSX 80 Holder AK 20 Nozzle DX 112 Nozzle DX 113 Cleaning set Replacement glass tube Order No.: 5 33 326 99 (UK: 5 33 323 99) WDD 81VIL WDD 81V 5 32 886 99 (UK: 5 32 883 99) 5 13 190 99 5 29 161 99 5 15 030 99 5 15 146 99 5 13 142 99 5 13 143 99 5 13 500 99 5 13 605 00 Desoldering iron DSX 80 Holder AK 20 Nozzle DX 112 Nozzle DX 113 Cleaning set Replacement glass tube 5 33 286 99 (UK: 5 33 283 99) 5 13 190 99 5 15 030 99 5 13 142 99 5 13 143 99 5 13 500 99 5 13 605 00 5 32 586 99 (UK: 5 32 583 99) 5 13 190 99 5 15 030 99 5 13 142 99 5 13 143 99 5 13 500 99 5 13 605 00 5 32 566 99 (UK: 5 32 563 99) Consists of: Power unit PUDD 81V Inline desoldering iron DSX V80 Holder AK V Nozzle DX 112 Nozzle DX 113 Cleaning set Order No.: 5 32 586 99 (UK: 5 32 583 99) 5 13 197 99 5 15 038 99 5 13 142 99 5 13 143 99 5 13 500 99 5 32 546 99 (UK: 5 32 543 99) 5 32 806 99 (UK: 5 32 803 99) WAD 101 Consists of: Power unit Hot air pencil HAP 1 Holder KH 27 Nozzle R 04 Nozzle R 06 Cleaning set 5 32 666 99 (UK: 5 32 663 99) (c) 2003, Cooper Industries, Inc. Specifications subject to change without notice. G E R M A N Y G R E A T Cooper Tools GmbH Carl-Benz-Str. 2 74354 Besigheim Tel: (07143) 580-0 Fax: (07143) 580-108 Cooper Tools Suite 15, Coniston House Towne Centre Washington, Tyne & Wear NE38 7RN Tel: (0191) 419 7700 Fax: (0191) 417 9421 B R I T A I N F R A N C E I T A L Y S W I T Z E R L A N D Cooper Tools S.A. 25 Avenue Maurice Chevalier 77330 Ozoir La Ferriere Tel: (1) 60.18.55.40 Fax: (1) 64.40.33.05 Cooper Italia S.p.A. Viale Europa 80 20090 Cusago (MI) Tel: (02) 9033101 Fax: (02) 90394231 Erem S.A. Rue de la Roseliere 8 1400 Yverdon les Bains Tel: (024) 426 12 06 Fax: (024) 425 09 77 5 56 616 00 / 02.03 La 10.0 Order No.: 5 27 115 99 5 15 027 99 5 87 278 21 5 87 278 22 5 13 500 99