Weller brings to the market an extended
generation of versatile soldering/desoldering,
SMD rework stations and tools.
Performance has been increased with soldering
irons and desoldering irons up to 150 W.
Choose between Weller stations with powerful
in-built pumps, or smaller units without
pumps that allow you to connect to your
own factory line.
Matrix
HAP 1 HOT AIR PENCIL ■■■
(KH 20 Support for HAP 1)
DSX 80 DESOLDERING IRON ■■■■
(AK 20 Support for DSX 80)
DS 80 UNC* DESOLDERING IRON ■■■■
(AK 20 Support for DS 80 UNC)
DSX V80 DESOLDERING IRON ■■■■
(AK V Support for DSX V80)
DS V80 UNC* DESOLDERING IRON ■■■■
(AK V Support for DS V80 UNC)
DS VT 80 DESOLDERING IRON ■■■■
(AK V Support for DS VT 80)
LR 21 SOLDERING PENCIL ■■■■■
(KH 20 Support for LR 21)
LR 82 SOLDERING IRON ■■■■■
(KH 27 Support for LR 82)
WSP 80 MICRO SOLDERING PENCIL ■■■■■
(WPH 80 Support for WSP 80)
WSP 150 SOLDERING IRON ■■■
(KH 27 Support for WSP 150)
MLR 21 MICRO SOLDERING PENCIL ■■■■■
(KH 15 Support for MLR 21)
MPR 80 ANTISTATIC PERITRONIC ■■■■■
(KH 25P Support for MPR 80)
WMP MICRO SOLDERING PENCIL ■■■■■
(WPHM support for WMP)
WST 20 THERMAL WIRE STRIPPER ■■■■■
(support included)
WHP 80 PREHEATING PLATE ■■■■■
WTA 50 TWEEZER ■■■■■
(AK 51 Support for WTA 50)
WSB 80 SOLDER BATH ■■■■■
WCB 1 CALIBRATION UNIT ■■■■
WCB 2 CALIBRATION UNIT ■■■■
*UNC. For use with nozzles with an inch thread.
All Weller stations easily connect to a variety of
new and existing Weller tools and accessories
to provide even greater flexibility. The matrix
below makes selection easy, and puts you
firmly in control of all your workbench needs.
WAD 101 WDD 81V
WMD 1
WMD 3
2
WDD 161V
Weller Multi-Digital Rework Station WMD 3
(With In-Built Pump)
Weller WMD 3 state-of-the-art technology
simultaneously provides multi-digital
control of working temperatures when
reworking conventional ICs and SMDs.
A soldering iron, desoldering iron and hot
air pencil can all be operated simultaneously
because of the WMD 3’s in-built micro-
processor that infinitely controls each
tool’s set temperature and airflow.
The display visually monitors each chosen
working temperature and times preset hot
gas pencil operations.
WELLER WMD 3
TECHNICAL DATA
DIMENSIONS: 240 x 270 x 105 mm (W x D x H)
LINE VOLTAGE: 230 V, 50 Hz
POWER INPUT: 310 W
PROTECTION CLASS: 1 and 3
FUSE: T 1,5 A located at the power entry module
CONTROLLING TOLERANCE: Soldering/Desoldering iron ±2 % of the final value
Hot air pencil ±30° C
TEMPERATURE CONTROL Soldering/Desoldering iron continuously 50° C - 450° C
WITH ZERO VOLTAGE CROSS SWITCHING: (WSP 150 150° C - 550° C)
Hot air pencil continuously 50° C - 550° C
PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min
Hot Air: max. 10 l/min
POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit
Lock-out key for set function
parameters of each channel.
Channel selector
for temperature and
air volume.
Timer/set back.
Vacuum connector
with filter cartridge.
Connector for
hot air pencil with
filter cartridge.
LED indicates
channel in
display.
Pilot light showing
heating pulses.
Three connectors for variable
combinations of hot air pencil,
desoldering iron, soldering iron
or other variable combinations.
Socket for potential
balance.
Multi-digital display shows the set
and read temperature of each tool
and air volume. Microprocessor controlled channel.
Continuously adjustable for
soldering iron, desoldering iron and hot
air pencil or other connectable tools.
Manometer for
vacuum control.
Antistatic coating on
housing meets ESD safe-
ty specifications.
Two connections for two
optional foot switches.
Mains switch.
3
Weller Multi-Digital Hot Air Station
WMD 1A (With In-Built Pump)
The multi application ability of this station
makes it ideal for use in situations where the
maximum amount of flexibility is required.
The station has an in built pump to provide
the air movement for the hot air pencil and
the vacuum for the desoldering tool and can
be used to rework both surface mounted and
through hole components.
The WMD 1S control unit is the base and
incorporates a micro processor controlled
system to regulate the solder processes.
The processor can also identify which tool is
being used and calibrate the output auto-
matically without the need for manual
adjustment.
By use of the WCB1 and WCB 2 control
boxes, additional functions can be pro-
grammed into the base unit such as, temper-
ature lock, set back time, temperature offset,
deg C / deg F, factory setting reset.
WELLER WMD 1A
TECHNICAL DATA
DIMENSIONS: 240 x 270 x 105 mm (W x D x H)
LINE VOLTAGE: 230 V, 50 Hz
POWER INPUT: 175 W
SAFETY CLASS: 1 and 3
FUSE: Glass tube fuse Ø 5 x 20; T 800 mA located at the power
entry module
CONTROLLING TOLERANCE: Soldering/Desoldering iron ±2 % of the final value
Hot air pencil ±30° C
TEMPERATURE CONTROL
WITH ZERO VOLTAGE CROSS SWITCHING: Hot air pencil continuously 50° C - 550° C
PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min
Hot air: max. 10 l/min
POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit
Mains switch.
Vacuum connector and filter cartridge.
Hot air nozzles. Different inter-
changeable types available.
HAP 1 Hot air pencil.
Air connector for hot air pencil.
Holder KH27 for
HAP 1 ho tair
pencil.
Antistatic coating on
housing meets
ESD safety specifications.
Seven-pin connector for
all desoldering, soldering
and accessory tools.
Temperature and hot air
control.
Manometer for
vacuum control.
Socket for potential balance.
Pilot light showing
heating pulses.
4
Multi-digital display shows
the set and read temperature
of each tool and air volume.
Weller Multi-Digital Desoldering Station
WMD 1D (With In-Built Pump)
WELLER WMD 1D
TECHNICAL DATA
Mains switch.
Multi-digital display shows the set and read
temperature of each tool and air volume.
Pilot light showing
heating pulses.
Seven-pin connector for
all desoldering, soldering
and accessory tools.
Manometer for
vacuum control.
Socket for potential balance.
Antistatic coating
on housing meets
ESD specifications.
DSX 80, 24V Desoldering iron
with 80W heating element.
'Longlife' tiplets.
Different interchangeable
types available.
5
DIMENSIONS: 240 x 270 x 105 mm (W x D x H)
LINE VOLTAGE: 230 V, 50 Hz
POWER INPUT: 175 W
PROTECTION CLASS: 1 and 3
FUSE: Glass tube fuse Ø 5 x 20; T 800 mA located at the power
entry module
CONTROLLING TOLERANCE: Soldering/Desoldering iron ±2 % of the final value
Hot air pencil ±30° C
TEMPERATURE CONTROL Soldering/Desoldering iron continuously 50° C - 450° C
WITH ZERO VOLTAGE CROSS SWITCHING: (WSP 150 150° C - 550° C)
PUMP: Max. low pressure 0,7 bar; max. conveyance 20 l/min
Hot air: max. 10 l/min
POTENTIAL BALANCE: Via 3,5 mm switch jack socket on the back of the unit
Temperature and hot
air control. Holder AK 20 for
DSX 80 desoldering
iron.
The multi application ability of this station
makes it ideal for use in situations where the
maximum amount of flexibility is required.
The station has an in built pump to provide
the vacuum for the desoldering tool and can
be used to rework both surface mounted and
through hole components.
The WMD 1S control unit is the base and
incorporates a micro processor controlled
system to regulate the desolder processes. The
processor can also identify which tool is being
used and calibrate the output automatically
without the need for manual adjustment.
By use of the WCB 1 and WCB 2 control
boxes, additional functions can be pro-
grammed into the base unit such as, temper-
ature lock, set back time, temperature offset,
deg C / deg F, factory setting reset.
Vacuum connector
and filter cartridge.
6
Weller Multi-Functional, Digital
Desoldering Station WDD 161V
The WDD 161V rework station is
a dual output unit supplied with
soldering and desoldering tools.
It features a micro processor controlled sys-
tem which allows independent tempera-
ture control of both tools. The station will
automatically recognize the tool in use
and calibrate itself for that tool. Vacuum
for the desoldering tool is generated by an
internal venturi driven from an external
compressed air source.
The selected operating temper-
atures are displayed on a digital
display switchable between tools. By use of
the WCB 1 and WCB 2 control boxes,
additional functions can be programmed
into the base unit such as, temperature
lock, set back time, temperature offset,
deg C / deg F, factory setting reset.
TECHNICAL DATA
DIMENSIONS: 166 x 115 x 101 mm (W x D x H)
POWER INPUT: 165 W
TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50° C - 450° C
COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry
compressed air
COMPRESSED AIR CONVERTER: Air consumption 35 l/min
Vacuum 55 KPA (8 psi)
COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter
PROTECTION CLASS: 1 (control unit), 3 (soldering tool)
Weller WDD 161V
Mains switch.
Antistatic coating on
housing meets ESD safety
specifications
Seven-pin connector for
connecting the DSX and
other soldering tools.
LED showing
heating pulses.
Multi-digital display shows
the set and read temperature
of DSX 80 or other connected tool.
Connector for vacuum
Connector for potential
balance
WSP 80 soldering pencil.
“Longlife”tiplets. Different
interchangeable types
available.
Finger switch to
control vacuum.
DSX 80 Desoldering iron.
Holder WPH 80 for
soldering pencil WSP 80.
Holder AK20 for DSX 80
desoldering iron.
Microprocessor controlled channel.
Automatically recognizes the DSX 80
and other connected tools and sets the
appropriate control parameters.
Weller Multi-Functional, Digital
Desoldering Station WDD 81V
The Weller WDD 81V Desoldering station
features digital process control for exact
temperature set. The in-built microprocessor
circuitry automatically recognizes all Weller
soldering irons and provides the optimal
settings of the connected tool. The station
comes with the DSX 80 Desoldering iron. A
range of desoldering suction tiplets enables
solder to be removed from a wide variety of
solder joints. The Weller CSF rework heads
can also be interchanged to provide total
flexibility in the rework of most Flat Packs.
An internal maintenance-free compressed
air converter provides the vacuum for the
desoldering iron. The WDD 81V requires a
compressed air supply.
The Weller WCB 1 or WCB 2 Calibration unit
can be connected to the WDD 81V to further
enhance programme setting. PC interface is
possible with the WCB 2 only.
WELLER WDD 81V
TECHNICAL DATA
DIMENSIONS: 166 x 115 x 101 mm (W x D x H)
POWER INPUT: 95 W
TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50° C - 450° C
COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry
compressed air
COMPRESSED AIR CONVERTER: Air consumption 35 l/min
Vacuum 55 KPA (8 psi)
COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter
PROTECTION CLASS: 1 (control unit), 3 (soldering tool)
Multi-digital display shows the set
and read temperature of the DSX 80
or other connected tool.
DSX 80 Desoldering iron.
Finger switch
to control vacuum.
Microprocessor controlled channel.
Automatically recognizes the DSX 80
and other connected tools and sets the
appropriate control parameters.
Connector for vacuum.
Seven-pin connector for
connecting the DSX and
other soldering tools.
Mains switch.
Pilot light showing
heating pulses.
7
Antistatic coating on housing
meets ESD safety specifications
Holder AK20 for
DSX 80 desoldering iron.
“Longlife”tiplets. Different
interchangeable types
available.
Connector for potential
balance
8
Weller Multi-Functional, Digital
Desoldering Station WDD 81VIL
The Weller WDD 81VIL Inline desoldering
station features digital process control for
exact temperature set. The in-built micro-
processor circuitry automatically recognizes
all Weller soldering irons and provides the
optimal settings of the connected tool. The
station comes with the DSX V80 Inline desol-
dering iron. A range of desoldering suction
tiplets enables solder to be removed from a
wide variety of solder joints. The Weller CSF
rework heads can also be interchanged to
provide total flexibility in the rework of most
Flat Packs. An internal maintenance-free
compressed air converter provides the vacu-
um for the inline desoldering iron. The
WDD 81VIL requires a compressed air supply.
The Weller WCB 1 or WCB 2 Calibration unit
can be connected to the WDD 81VIL to
further enhance programme setting. PC
interface is possible with the WCB 2 only.
WELLER WDD 81VIL
TECHNICAL DATA
DIMENSIONS: 166 x 115 x 101 mm (W x D x H)
POWER INPUT: 95 W
TEMPERATURE CONTROL : Soldering/Desoldering iron continuously 50° C - 450° C
COMPRESSED AIR: Inlet pressure 500 KPA - 600 KPA (58 - 87 psi) oil-free, dry
compressed air
COMPRESSED AIR CONVERTER: Air consumption 35 l/min
Vacuum 55 KPA (8 psi)
COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0.24") external diameter
PROTECTION CLASS: 1 (control unit), 3 (soldering tool)
Multi-digital display shows the set
and read temperature of the
DSX V80 or other connected tool.
DSX V80 Desoldering iron.
Finger switch
to control vacuum.
Microprocessor controlled channel.
Automatically recognizes the DSX V80
and other connected tools and sets the
appropriate control parameters.
Connector for vacuum.
Seven-pin connector for
connecting the DSX V80
and other soldering tools.
Mains switch.
Pilot light showing
heating pulses.
Antistatic coating on housing
meets ESD safety specifications
“Longlife”tiplets. Different
interchangeable types
available.
Connector for potential
balance
Holder AK V for
DSX V80 desoldering
iron.
9
Weller Multi-Functional, Digital
Hot Air Station WAD 101
The Weller WAD 101 Hot air station features
digital process control for accurate
temperature set. The in-built microprocessor
circuitry automatically recognizes all Weller
soldering irons and provides the optimal
settings of the connected tools as well as
the HAP 1 that comes as standard with the
station. A wide range of nozzles and tools
makes the WAD 101 ideal in many soldering
and desoldering applications of surface
mount devices. The WAD 101 requires a
compressed air supply with oil-free, dry air
or nitrogen (N2) where the airflow is
manually controlled.
The Weller WCB 1 or WCB 2 Calibration unit
can be connected to the WAD 101 to further
enhance programme setting. PC interface is
possible with the WCB 2 only.
WELLER WAD 101
TECHNICAL DATA
DIMENSIONS: 166 x 134 x 101 mm (W x D x H)
POWER INPUT: 105 W
TEMPERATURE CONTROL: Hot air pencil 50° C - 550° C
FLOW RATE: Approx. 0-10 l/min
COMPRESSED AIR: Inlet pressure 400 KPA (58 psi) oil-free, dry compressed
air or nitrogen (N2)
COMPRESSED AIR CONNECTION: Compressed air hose of 6 mm (0,24") external diameter
PROTECTION CLASS: 1 (control unit), 3 (soldering tool)
Multi-digital display
sets and reads
temperature of the
selected tool
HAP 1 Hot air pencil
Finger switch to
control air manually
Holder KH27 for
HAP 1 ho tair pencil
Connector for
hot air
Seven-pin connector for
connecting the HAP 1 and
other soldering tools
Mains switch
Air volume control
Pilot light showing
heating pulses
Antistatic coating on
housing meets
ESD specifications
Microprocessor controlled channel.
Automatically recognizes the HAP 1
and other connected tools and sets the
appropriate control parameters
Hot air nozzles. Different
interchangeable types
available
Connector for potential
balance
Weller Flexibility.
Refer to the matrix to make your choice of connecting tools for the WMD 3,
WMD 1A + D, WDD 161V, WDD 81V + VIL and WAD 101 (see matrix page 2).
HAP 1 Hot air pencil
The HAP 1, 100W/24V, provides a directional hot airflow
that is adjustable and static-free. Electronically tempera-
ture controlled from 50˚C to 550˚C. Different nozzles
available as accessories. Finger switch controls speed
adjustable pump. Hot air pencil set, consisting of HAP 1
with finger switch, KH 27 Support for pencil, nozzle 1,2
and 3,0 mm, key and nutdriver for nozzle changing.
HAP 1
5 33 114 99
DSX 80 (DS 80 UNC*) Desoldering iron and service kit
An 80W/24V desoldering iron for electronics rework.
Electronically temperature controlled. Micro-finger
switch controls quick-start, fast action vacuum pump.
Different interchangeable tiplets, plus several CSF
devices are available as accessories. DS 80 (DS 80 UNC*)
set, consisting of DS 80 (DS 80 UNC*) Desoldering iron
AK 20 Support, cleaning tool, glass collector, two
desoldering nozzles, gasbet, anti-bloc paste, filter.
DSX 80 (DS 80 UNC*)
5 33 138 99
(5 13 191 99)
DSX V80 (DS V80 UNC*) Desoldering iron
Connectable to all 80W desoldering stations. Handle
utilizes the tin collector to hold the extracted solder.
Easy to clean by use of the bayonet fitting. DSX V80 set,
consisting of DSX V80 Desoldering iron, AKV Support for
iron.
DSX V80 (DS V80 UNC*)
5 33 137 99 (5 33 129 99)
DS VT80 Desoldering iron
The model DS VT80 heats up Weller CSF desoldering
heads and is equipped with a spring-loaded vacuum
pipette, which makes this tool ideal for rework of larger
SMD components. DS VT80 set, consisting of DS VT80
Desoldering iron, AK V Support for iron.
DS VT80
5 33 134 99
LR 21 Antistatic soldering pencil
Electronically temperature controlled 50W/24V soldering
pencil. LR 21 set, consisting of LR 21 Antistatic soldering
pencil, KH 20 Support for pencil.
LR 21
5 33 112 99
LR 82 Antistatic soldering iron
An 80W/24V soldering iron for high mass soldering. Dual
sensor, electronically temperature controlled. LR 82 set,
consisting of LR 82 Antistatic soldering iron, KH 27
Support for iron.
LR 82
5 33 113 99
WSP 80 Micro soldering pencil
A micro soldering pencil, 80W/24V. This soldering pencil
can be universally used in all situations from extremely
delicate soldering to those where there is a greater
temperature requirement. WSP 80 set, consisting of
WSP 80 Micro soldering pencil with WPH 80 Support.
WSP 80
5 29 161 99
WSP 150
5 33 135 99
The WSP 150, 150W/24V, soldering iron was specially
developed for soldering tasks with extremely high heat
requirements. The 150 W heater power combined with
optimal transfer of heat to the soldering iron bit guaran-
tee the high performance capability of the soldering
iron. WSP 150 set, consisting of WSP 150 Soldering iron,
KH 27 Support for iron.
WSP 150 Soldering iron
*UNC. For use with nozzles with an inch thread.
10
MLR 21 Micro soldering pencil
A micro soldering pencil, 25W/24V with antistatic cord,
suitable for miniature soldering work. Electronically
temperature controlled. MLR 21 set, consisting of
MLR 21 Micro soldering pencil, KH 15 Support for pencil.
MLR 21
5 33 111 99
MPR 80 Antistatic Peritronic soldering pencil
An 80W Antistatic Peritronic soldering pencil that gives
all-round vision when making intricate connections.
Antistatic cord and handle. Electronically temperature
controlled. Consists of MPR 80 Antistatic and KH 25P
Support.
WMP Micro soldering pencil
The 65W micro pencil is up to the task with superior per-
formance for both heat-up and thermal efficiency.
Suitable to handle all micro components and fine pitch
tasks. The WMP provides an extremely short tip-to-grip
distance. The heater is integrated into the handle. When
the tip wear out the heating element goes on. WMP set
consisting of WMP micro soldering pencil and WPHM
holder for WMP.
WST 20 Thermal wire stripper with support
The WST 20, 50W/24V, copes with all known thermoelas-
tic plastics. Adjustable for a stripping length up to 30
mm. Additional blades available for stripping flat cables
and shrinking.
WHP 80 (80W/24V) Preheating plate
With a heating surface of 80 x 50 mm, they preheat
IC boards prior to micro rework.
WHP 80
5 27 028 99
WTA 50 Tweezer
This tweezer is used to desolder SMD components.
The tweezer has two moveable heating elements.
WTA 50 set, consisting of WTA 50 Tweezer, AK 51
Support for Tweezer.
WSB 80 Solder bath
The WSB 80 is a very useful rework preparation tool.
The solder bath is temperature controlled
continuously from 50˚C to 450˚C via an existing
80W power source. The solder bath can be used
to tin wire ends and clean leads of all extraneous
solder particles in preparation for reworking.
WSB 80
5 27 040 99
WTA 50
5 33 133 99
MPR 80
5 33 131 99
WMP
5 33 155 99
WST 20
5 25 030 99
WCB 1, WCB 2 Calibration units
The intelligence of the digital Weller units can be
further enhanced by being programmed by either
the WCB 1 or WCB 2 Calibration unit. Both the
WCB 1 and the WCB 2 feature temperature lock-
out and off-set capabilities up to + 40˚C. The WCB 2
has the added ability to PC interface (RS 232) and a
thermoelement type K and measuring tip.
WCB 1
5 31 181 99
WCB 2
5 31 180 99
11
x
1
(mm) x y
1
(mm)
x
1
> x + 0,3
y
1
> y + 0,3
CSF-Head
Order No.
CSF Accessories
Rubber insert
(spare)
Adaptor for
DS VT80
Adaptor for
DS 80,
DS V80
12,0 x 12,0 5 87 417 33 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
12,0 x 14,5 5 87 417 34 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
12,7 x 12,7 5 87 417 35 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
17,0 x 17,0 5 87 417 36 11 5 87 417 89 5 87 417 16 5 87 417 85 5 87 418 04 5 87 137 98
17,0 x 23,0 5 87 417 37 16 5 87 417 90 5 87 417 17 5 87 417 86 5 87 418 05 5 87 137 98
19,6 x 19,6 5 87 417 38 11 5 87 417 89 5 87 417 16 5 87 417 85 5 87 418 04 5 87 137 98
12,7 x 12,7 5 87 417 39 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
17,8 x 17,8 5 87 417 40 11 5 87 417 89 5 87 417 16 5 87 417 85 5 87 418 04 5 87 137 98
20,4 x 20,4 5 87 417 41 16 5 87 417 90 5 87 417 17 5 87 417 86 5 87 418 05 5 87 137 98
25,4 x 25,4 5 87 417 42 16 5 87 417 90 5 87 417 17 5 87 417 86 5 87 418 05 5 87 137 98
30,4 x 30,4 5 87 417 43 16 5 87 417 90 5 87 417 17 5 87 417 86 5 87 418 05 5 87 137 98
5,5 x 10,0 5 87 417 23 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
5,8 x 10,5 5 87 417 24 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
6,7 x 10,0 5 87 417 25 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
9,3 x 13,0 5 87 417 26 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
9,4 x 10,0 5 87 417 27 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
9,8 x 18,0 5 87 417 28 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
10,0 x 16,0 5 87 417 29 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
10,5 x 16,0 5 87 417 30 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
10,7 x 18,0 5 87 417 31 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
11,0 x 26,5 5 87 417 32 11 5 87 417 89 5 87 417 16 5 87 417 85 5 87 418 04 5 87 137 98
for DS 80 (DS 80 UNC),DSX 80, DS V80 (DS V80 UNC), DSX V80 and DS VT80 for SMD’s
chip desoldering tiplets for flat packs
DS 80 (DS 80 UNC),DSX 80 DS V80 (DS V80 UNC), DSX V80 DS VT80
SOJ-Case
9,0 x 18,0 5 87 417 44 6 5 87 417 88 5 87 417 15 5 87 417 84 5 87 418 03 5 87 137 99
Adaptor
Ø
CSF-Q
CSF-Ql
CSF-D
CSF-Dl
Adaptor for
DS 80 UNC,
DS V80 UNC
12
Adaptor for
DSX80, DSX V80
Accessories
DX110 Nozzle 1,9 0,7 23 5 13 140 00
DX111 Nozzle 2,5 0,7 23 5 13 141 00
DX112 Nozzle 2,3 1,0 23 5 13 142 00
DX113 Nozzle 2,5 1,2 23 5 13 143 00
DX113HM Nozzle 2,5 1,2 23 5 13 150 00
with improved thermal transfer
DX114 Nozzle 3,3 1,8 23 5 13 144 00
DX115 Nozzle 1,9 0,7 23 5 13 145 00
DX116 Nozzle 2,7 1,2 29 5 13 146 00
DX117 Nozzle 2,9 1,5 23 5 13 147 00
DX118 Nozzle 1.5 0.7 23 5 13 148 00
DX119 Needle Tiplet 1,1 0,7 31 5 13 151 00
for removal of solder bridges in connection with hot air pencil
DX120 Nozzle 2,5 1,1 22 5 13 152 00
without inside tube, for cleaning of SMD pads
Measuring 3,3 0,55 21.5 5 13 153 99
Nozzle
for temperature measurement with thermocouple 0.5
Conus insert for cleaning tool 5 87 067 94
Nozzle Set DX 110-DX115 5 13 790 99
For easier rework and repair, Weller has a large range of desoldering
nozzles and soldering tips.
Nozzles for desoldering
iron DSX 80 and
DSX V80:
Model Description mm mm mm Order No.
13
Threadless nozzles for desoldering iron DSX 80 und DSX V80
The new X series nozzle feature a threadless fixture system whereby
the nozzle is inserted into the head and locked into place by apllying
a 1/4 turn. This feature allows the nozzles to be quickly and easily
exchanged and also improves the rate of thermal transfer from the
head to the nozzle.
DSX 80 DSX V80
Hot Air Nozzles
for hot air pencil HAP 1
Description Dimensions Type Order No.
(mm)
Nozzle 18,0 x 18,0 Q10 5 87 277 85
Nozzle 12,5 x 15,0 Q08 5 87 277 83
Nozzle 15,0 x 10,0 Q06 5 87 277 80
Nozzle 6,0 x 9,0 Q04 5 87 277 78
Nozzle 6,0 x 6,5 Q02 5 87 277 77
Nozzle 10,0 x 18,0 D10 5 87 277 84
Nozzle 15,0 x 10,0 D08 5 87 277 81
Nozzle 10,0 x 13,0 D06 5 87 277 82
Nozzle 10,5 x 10,5 D04 5 87 277 79
Measuring nozzle R01 5 87 278 08
14
Description Dimensions Type Order No.
(mm)
Flat nozzle 12,0 x 1,5 F06 5 87 277 72
Flat nozzle 10,5 x 1,5 F04 5 87 277 73
Flat nozzle 8,0 x 1,5 F02 5 87 277 74
Straight Ø 2,0 R10 5 87 277 87
Bent Ø 2,0 R08 5 87 277 86
Nozzle Ø 3,0 R06 5 87 278 22
Nozzle Ø 1,2 R04 5 87 278 21
Nozzle Ø 0,8 R02 5 87 278 23
Dual nozzle Ø 1,5 x 10,0 FD4 5 87 277 75
Dual nozzle Ø 1,5 x 8,0 FD2 5 87 277 76
Hot Air Nozzles
for hot air pencil HAP 1
15
16
Soldering Tips
for soldering iron LR 82
Description Width A Thickness B Type Order No.
Chisel 3,2 mm 1,0 mm HT 1 5 44 260 99
Chisel 5,2 mm 1,2 mm HT 2 5 44 261 99
Chisel 7,0 mm 1,2 mm HT 3 5 44 262 99
Screwdriver 3,2 mm 1,0 mm HT C 5 44 267 99
Screwdriver 4,6 mm 1,0 mm HT D 5 44 268 99
Screwdriver 5,6 mm 1,0 mm HT E 5 44 269 99
Round tip 2,4 mm 8,3 mm HT BS 5 44 264 99
Round tip 3,2 mm 8,3 mm HT CS 5 44 265 99
Round tip 5,0 mm 8,3 mm HT DS 5 44 266 99
Calibration tip - - - 5 44 263 99
A
B
A
B
A
B
A
B
A
B
A
B
B
A
B
A
B
A
for soldering pencil LR 21
Soldering Tips
Description Width Type Order No. for Order No. for
regular solder HPB solder
Screwdriver tip 0,8 mm ET H 5 41 000 99 5 41 000 74
1,6 mm ET A 5 41 001 99 5 41 001 73
2,4 mm ET B 5 41 002 99 5 41 002 71
3,2 mm ET C 5 41 003 99 5 41 003 72
4,6 mm ET D 5 41 004 99 -
5,6 mm ET E 5 41 005 99 -
Long screwdriver tip 1,2 mm ET K 5 41 006 99 -
2,0 mm ET L 5 41 007 99 5 41 007 73
3,2 mm ET M 5 41 008 99 -
Round tip, blunt 0,8 mm ET P 5 41 038 99 -
2,4 mm ET BS 5 41 009 99 -
3,2 mm ET CS 5 41 010 99 -
5,0 mm ET DS 5 41 011 99 -
Sloped round tip 0,8 mm ET AA 5 41 031 99 -
1,2 mm ET F 5 41 012 99 -
2,4 mm ET BB 5 41 055 99 -
3,2 mm ET CC 5 41 013 99 -
Conical long tip 0,8 mm ET O 5 41 014 99 -
0,4 mm ET S 5 41 017 99 -
Screwdriver tip 1,6 mm ET R 5 41 015 99 -
Flat tip, slightly bent, 3,2 mm ET MX 5 41 016 99 -
one side wettable only
Chip soldering/desoldering tip 2,5 x 1,5 mm ET SMD 5 41 039 99 -
3,8 x 1,5 mm ET SMD 5 41 040 99
Soldering tip for J-Leads
- ET JL 5 41 018 99 -
Soldering tip for Gullwings - ET GW 5 41 045 99 -
ET Calibration nozzle - - 5 24 750 99 -
17
Soldering Tips
Description Width Type Order No.
Micropoint 0,25 mm MT 1 5 44 101 99
Micropoint 0,2 mm MT 1SL 5 44 115 99
0,25 mm MT 1S 5 44 105 99
Chisel 1,6 mm MT 6 5 44 106 99
Round tip 1,2 mm MT 4 5 44 104 99
Screwdriver 0,8 mm MT H 5 44 112 99
1,6 mm MT A 5 44 110 99
2,4 mm MT B 5 44 111 99
Screwdriver 0,8 mm MT HX* 5 44 113 99
bent *only with barrel nut 5 87 207 01
Soldering tip - MT JL 5 44 118 99
for J-Lead
Soldering tip Ø 2,0 mm MT GW 5 44 119 99
for Gullwings Ø 4,0 mm MT GW 5 44 120 99
Calibration tip - - 5 44 114 99
for soldering pencil MLR 21
18
19
Soldering Tips
For micro soldering pencil WMP
Description Width A Thickness B Length C Type / Order No.
Chisel tip 0,8 mm 0,4 mm 8,4 mm NTH
1,2 mm 0,4 mm 8,4 mm NTK
1,6 mm 0,4 mm 8,4 mm NTA
1,6 mm 0,4 mm 9,5 mm NT6
2,4 mm 0,8 mm 7,4 mm NTB
3,2 mm 0,8 mm 7,8 mm NTC
4,0 mm 0,8 mm 7,8 mm NTD
Chisel tip, bent 0,4 mm 1,6 mm 8,2 mm NTAX
Round tip, bent 1,6 mm 0,8 mm 8,6 mm NT1X
Round tip 0,25 mm - 7,4 mm NT1
Round tip small 0,25 mm - 8,5 mm NT1S
Round tip, sloped 1,2 mm - 9,9 mm NT4
45°
Gull Wing 2,0 mm 3,0 mm 13,4 mm NTGW
NT Measuring tip - - - NTMS
Description Width A Thickness B Length C Component Type/
Type Order No.
Blade 10,4 mm 0,6 mm 7,1 mm Any (for pad clean-up) NTSMT01
16,8 mm 0,6 mm 7,1 mm Any (for pad clean-up) NTSMT02
20,8 mm 0,6 mm 7,1 mm Any (for pad clean-up) NTSMT03
Slot 1,8 mm 9,4 mm 1,8 mm Chip NTSMT04
1,5 mm 2,3 mm 1,8 mm Chip NTSMT05
2,5 mm 1,7 mm 1,4 mm Chip NTSMT06
2,3 mm 4,5 mm 1,8 mm Chip NTSMT07
Tunnel 4,6 mm 5,1 mm 2,3 mm DIP NTSMT08
10,4 mm 5,1 mm 2,3 mm DIP NTSMT09
11,5 mm 6,9 mm 2,3 mm DIP NTSMT10
13,2 mm 9,5 mm 3,2 mm DIP NTSMT11
15,8 mm 9,5 mm 3,2 mm DIP NTSMT12
18,3 mm 9,5 mm 3,2 mm DIP NTSMT13
18,8 mm 9,0 mm 3,2 mm DIP NTSMT14
Quad 2,7 mm 7,7 mm 3,8 mm PLCC & QFP NTSMT15
10,4 mm 10,4 mm 3,8 mm PLCC & QFP NTSMT16
12,7 mm 12,7 mm 3,8 mm PLCC & QFP NTSMT17
13,7 mm 8,6 mm 3,8 mm PLCC & QFP NTSMT18
19,1 mm 19,1 mm 5,6 mm PLCC & QFP NTSMT19
23,2 mm 17,3 mm 3,8 mm PLCC & QFP NTSMT20
24,5 mm 24,5 mm 5,6 mm PLCC & QFP NTSMT21
29,6 mm 29,6 mm 5,6 mm PLCC & QFP NTSMT22
B
C
A
A
C
B
C
B
A
A
B
C
Description Width A Thickness B Type Order No. Order No. Order No.
regular solder HPB solder lead free solder
Round tip 0,25 mm LT 1 5 44 435 99 - -
Long tip, 0,2 mm LT 1L 5 44 423 99 - -
conical
Round tip 0,2 mm 1,6 mm LT 1S 5 44 436 99 - -
Round tip 1,6 mm LT AS 5 44 404 99 - -
Round tip 3,2 mm LT CS 5 44 411 99 - -
Chisel tip 0,8 mm 0,4 mm LT H 5 44 437 99 - -
0,8 mm 0,4 mm LT H HPB 5 44 430 99 -
Round tip, 1,2 mm LT F 5 44 408 99 - -
spade
Chisel tip 1,2 mm 0,4 mm LT K 5 44 438 99 - -
Chisel tip 1,6 mm 0,7 mm LT A 5 44 440 99 - -
1,6 mm 0,7 mm LT A HPB 5 44 431 99 -
Long chisel 2,0 mm 1,0 mm LT L 5 44 414 99 - -
tip
Chisel tip 2,4 mm 0,8 mm LT B 5 44 405 99 - -
2,4 mm 0,8 mm LT B HPB 5 44 432 99 -
2,4 mm 0,8 mm LT B LL - 5 44 446 99
Chisel tip 3,2 mm 0,8 mm LT C 5 44 407 99 - -
3,2 mm 0,8 mm LT C LL - 5 44 447 99
Long chisel 3,2 mm 1,2 mm LT M 5 44 415 99 - -
tip
Chisel tip 4,6 mm 0,8 mm LT D 5 44 409 99 - -
4,6 mm 0,8 mm LT D LL - 5 44 448 99
Round tip, 1,2 mm LT 4 5 44 439 99 - -
spade
Soldering Tips
for WSP 80, WSP 80 FE and MPR 80
20
WSP 80 (FE)
MPR 80
Description Width A Thickness B Type Order No.
regular solder
Tip for Gullwings 2,4 mm 3, 2 mm LT GW 5 44 410 99
Long tip, conical 0,4 mm LT S 5 44 406 99
Long tip, bent 0,2 mm LT 1LX 5 44 424 99
Chisel tip, bent 0,8 mm 0,4 mm LT HX 5 44 420 99
1,6 mm 0,7 mm LT ALX 5 44 443 99
2,4 mm 0,8 mm LT BX 5 44 442 99
Chisel tip, bent 1,2 mm 0,4 mm LT 4X 5 44 428 99
Chisel tip, bent 1,6 mm 0,8 mm LT AX 5 44 427 99
Round tip, bent 2,0 mm 0,4 mm LT 1X 5 44 425 99
Round tip, bent 2,0 mm 0,4 mm LT 1SLX 5 44 426 99
Round tip, spade 2,4 mm 4,0 mm LT BB 5 44 444 99
3,2 mm 6,0 mm LT CC 5 44 445 99
LT Desoldering tip 10,5 mm 0,6 mm 5 44 429 99
LT Adaptor for 13,5 mm 5 44 417 99
SMD tips
LT Measuring tip 5 44 446 00
Soldering Tips
for WSP 80, WSP 80 FE, MPR 80
21
WSP 80 (FE)
MPR 80
Tip set 0,5 mm 0,5 mm WTA 1S 5 44 145 99
Tip Set 1,0 mm 0,5 mm WTA 1 5 44 141 99
Tip set 3,0 mm 0,5 mm WTA 2 5 44 146 99
Tip set 6,0 mm 0,5 mm WTA 3 5 44 147 99
Tip set 12,5 mm 0,5 mm WTA 4 5 44 143 99
Tip set 18,5 mm 0,5 mm WTA 5 5 44 144 99
Tip set vertical use 1,0 mm 0,5 mm WTA 11 5 44152 99
Tip set vertical use 3,0 mm 0,5 mm WTA 12 5 44 153 99
Soldering Tips
For WT 50 and WTA 50 tweezer
22
Description Width A Thickness B Type Order No.
For soldering iron WSP 150
Chisel tip 3,2 mm 1,2 mm LHT C 5 44 455 99
Chisel tip 4,7 mm 1,8 mm LHT D 5 44 452 99
Chisel tip 6,7 mm 1,8 mm LHT E 5 44 451 99
Chisel tip 9,3 mm 1,8 mm LHT F 5 44 450 99
Chisel tip, bent 5 mm 2 mm LHT DX 5 44 462 99
7 mm 2 mm LHT EX 5 44 461 99
10 mm 2 mm LHT FX 5 44 460 99
LHT Calibration tip - - - 5 44 453 99
WSP 150
WTA 50
23
Additional Support and Holders
5 15 012 99 WPHM
5 15 010 99
5 15 140 99
5 15 042 99 5 15 019 995 15 038 99
5 15 020 99 5 15 027 99
5 15 033 99
5 15 030 99
AK 1 Support for DSX 80 (DS 80 UNC)
Desoldering iron, HAP 1 Hot air pen-
cil, LR 21 and LR 82 Antistatic solder-
ing pencils
KH 27 Support for LR 82 Soldering
iron, HAP 1 and WSP 150
AK V Support for DS VT80 and
DSX V80 (DS V80 UNC) Desoldering
iron
KH 25P Support for MPR 80 Peritronic
soldering pencil
AK 51 Support for WTA 50 Tweezer
WPH 80 Support for WSP 80
Micro soldering pencil
WPHM support for WMP micro sol-
dering pencil
AK 21 Support for MPR 80 Peritronic
soldering pencil
AK 20 Support for DSX 80 (DS 80
UNC) Desoldering iron and HAP 1
Hot air pencil
KH 15 Support for MLR 21
Micro soldering pencil
KH 20 Support for LR 21 Antistatic
soldering pencil and HAP 1 Hot air
pencil
WMD 1D
WDD 81VIL
WMD 1A
WDD 81V
WMD 3
WDD 161V
WAD 101
Consists of:
■Power unit
Order No.: 5 33 026 99
(UK: 5 33 023 99)
Consists of:
■Power unit WMD 1S 5 33 286 99
(UK: 5 33 283 99)
■Hot air pencil HAP 1 5 27 115 99
■Holder KH 27 5 15 027 99
■Nozzle R 04 5 87 278 21
■Nozzle R 06 5 87 278 22
■Cleaning set 5 13 500 99
Order No.: 5 33 306 99
(UK: 5 33 303 99)
Consists of:
■Power unit
■Hot air pencil HAP 1 5 27 115 99
■Holder KH 27 5 15 027 99
■Nozzle R 04 5 87 278 21
■Nozzle R 06 5 87 278 22
■Cleaning set 5 13 500 99
Order No.: 5 32 666 99
(UK: 5 32 663 99)
Consists of:
■Power unit WMD 1S 5 33 286 99
(UK: 5 33 283 99)
■Desoldering iron DSX 80 5 13 190 99
■Holder AK 20 5 15 030 99
■Nozzle DX 112 5 13 142 99
■Nozzle DX 113 5 13 143 99
■Cleaning set 5 13 500 99
■Replacement glass tube 5 13 605 00
Order No.: 5 33 326 99
(UK: 5 33 323 99)
Consists of:
■Power unit PUDD 161V 5 32 886 99
(UK: 5 32 883 99)
■Desoldering iron DSX 80 5 13 190 99
■Soldering pencil WSP 80 5 29 161 99
■Holder AK 20 5 15 030 99
■Holder WPH 80 5 15 146 99
■Nozzle DX 112 5 13 142 99
■Nozzle DX 113 5 13 143 99
■Cleaning set 5 13 500 99
■Replacement glass tube 5 13 605 00
Order No.: 5 32 806 99
(UK: 5 32 803 99)
Consists of:
■Power unit PUDD 81V 5 32 586 99
(UK: 5 32 583 99)
■Desoldering iron DSX 80 5 13 190 99
■Holder AK 20 5 15 030 99
■Nozzle DX 112 5 13 142 99
■Nozzle DX 113 5 13 143 99
■Cleaning set 5 13 500 99
■Replacement glass tube 5 13 605 00
Order No.: 5 32 566 99
(UK: 5 32 563 99)
Consists of:
■Power unit PUDD 81V 5 32 586 99
(UK: 5 32 583 99)
■Inline desoldering
iron DSX V80 5 13 197 99
■Holder AK V 5 15 038 99
■Nozzle DX 112 5 13 142 99
■Nozzle DX 113 5 13 143 99
■Cleaning set 5 13 500 99
Order No.: 5 32 546 99
(UK: 5 32 543 99)
GERMANY GREAT BRITAIN
Cooper Tools GmbH Cooper Tools
Carl-Benz-Str. 2 Suite 15, Coniston House
74354 Besigheim Towne Centre
Tel: (07143) 580-0 Washington, Tyne & Wear
Fax: (07143) 580-108 NE38 7RN
Tel: (0191) 419 7700
Fax: (0191) 417 9421
FRANCE ITALY SWITZERLAND
Cooper Tools S.A. Cooper Italia S.p.A. Erem S.A.
25 Avenue Maurice Chevalier Viale Europa 80 Rue de la Roselière 8
77330 Ozoir La Ferrière 20090 Cusago (MI) 1400 Yverdon les Bains
Tél: (1) 60.18.55.40 Tel: (02) 9033101 Tel: (024) 426 12 06
Fax: (1) 64.40.33.05 Fax: (02) 90394231 Fax: (024) 425 09 77
5 56 616 00 / 02.03 La 10.0
© 2003, Cooper Industries, Inc.
Specifications subject to change without notice.
