Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
LM2574x SIMPLE SWITCHER® 0.5-A Step-Down Voltage Regulator
1
1 Features
1 New product available: TPS560430, 36-V, 600-
mA synchronous step-down converter
3.3-V, 5-V, 12-V, 15-V, and adjustable output
versions
Adjustable version output voltage range: 1.23 V to
37 V (57 V for HV version) ±4% maximum over
line and load conditions
Specified 0.5-A output current
Wide input voltage range: 40 V, up to 60 V for HV
Version
Requires only four external components
52-kHz Fixed-frequency internal oscillator
TTL shutdown capability, low-power standby
mode
High efficiency
Uses readily available standard inductors
Thermal shutdown and current-limit protection
Create a custom design using the LM2574 with
the WEBENCH®Power Designer
2 Applications
Simple high-efficiency step-down (buck) regulator
Efficient preregulator for linear regulators
On-card switching regulators
Positive-to-negative converter (buck-boost)
3 Description
The LM2574xx series of regulators are monolithic
integrated circuits that provide all the active functions
for a step-down (buck) switching regulator, capable of
driving a 0.5-A load with excellent line and load
regulation. These devices are available in fixed output
voltages of 3.3 V, 5 V, 12 V, 15 V, and an adjustable
output version.
Requiring a minimum number of external
components, these regulators are simple to use and
include internal frequency compensation and a fixed-
frequency oscillator.
The LM2574xx series offers a high-efficiency
replacement for popular three-terminal linear
regulators. Because of its high efficiency, the copper
traces on the printed-circuit board (PCB) are normally
the only heat sinking needed.
A standard series of inductors optimized for use with
the LM2574 are available from several different
manufacturers. This feature greatly simplifies the
design of switch-mode power supplies.
Other features include a specified ±4% tolerance on
output voltage within specified input voltages and
output load conditions, and ±10% on the oscillator
frequency. External shutdown is included, featuring
50-μA (typical) standby current. The output switch
includes cycle-by-cycle current limiting, as well as
thermal shutdown for full protection under fault
conditions.
The TPS560430 is a newer generation buck
converter, being functionally equivalent to LM2574. It
offers reduced BOM cost, increased efficiency, and
reduced solution size. See the Device Comparison
Table to compare specifications. Start WEBENCH
Design with TPS560430.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM2574, LM2574HV SOIC (14) 8.992 mm × 7.498 mm
PDIP (8) 6.35 mm × 9.81 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application (Fixed Output Voltage Versions)
2
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics for All Output Voltage
Versions..................................................................... 5
6.6 Electrical Characteristics 3.3-V Version................. 5
6.7 Electrical Characteristics 5-V Version.................... 6
6.8 Electrical Characteristics 12-V Version.................. 6
6.9 Electrical Characteristics 15-V Version.................. 6
6.10 Electrical Characteristics Adjustable Version....... 7
6.11 Typical Characteristics............................................ 8
7 Detailed Description............................................ 11
7.1 Overview................................................................. 11
7.2 Functional Block Diagram....................................... 11
7.3 Feature Description................................................. 11
7.4 Device Functional Modes........................................ 13
8 Application and Implementation ........................ 14
8.1 Application Information............................................ 14
8.2 Typical Applications ................................................ 19
9 Power Supply Recommendations...................... 26
10 Layout................................................................... 26
10.1 Layout Guidelines ................................................. 26
10.2 Layout Example .................................................... 27
10.3 Grounding ............................................................. 27
10.4 Thermal Considerations........................................ 27
11 Device and Documentation Support ................. 29
11.1 Device Support...................................................... 29
11.2 Documentation Support ........................................ 31
11.3 Receiving Notification of Documentation Updates 31
11.4 Support Resources ............................................... 31
11.5 Trademarks........................................................... 31
11.6 Electrostatic Discharge Caution............................ 31
11.7 Glossary................................................................ 31
12 Mechanical, Packaging, and Orderable
Information........................................................... 31
4 Revision History
Changes from Revision E (July 2018) to Revision F Page
Added verbiage for TPS560430............................................................................................................................................. 1
Changes from Revision D (April 2016) to Revision E Page
Added links for WEBENCH ................................................................................................................................................... 1
maximum supply voltage in Abs Max Ratings from "4.5" to "45" to correct typo................................................................... 4
Changes from Revision C (April 2013) to Revision D Page
Added Device Information table, ESD Ratings table, Feature Description section, Device Functional Modes,
Application and Implementation section, Power Supply Recommendations section, Layout section, Device and
Documentation Support section, and Mechanical, Packaging, and Orderable Information section ..................................... 1
Changed RθJA value in SOIC column to 77.1 ........................................................................................................................ 4
Split test conditions row of the Electrical Characteristics table to include TJ= 25°C and TJ< 25°C MIN, TYP, and
MAX values............................................................................................................................................................................. 5
Split test conditions in ILrow to rearrange the MIN, TYP, and MAX values ......................................................................... 5
Changes from Revision B (November 2004) to Revision C Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
1NC 14 NC
2NC 13 NC
3FB 12 OUTPUT
4SIG_GND 11 NC
5ON/OFF 10 VIN
6PWR_GND 9 NC
7NC 8 NC
1FB 8 NC
2SIG_GND 7 OUTPUT
3ON/OFF 6 NC
4PWR_GND 5 VIN
3
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
5 Pin Configuration and Functions
P Package
8-Pin PDIP
Top View NPA Package
14-Pin SOIC
Top View
Pin Functions
PIN I/O DESCRIPTION
NAME PDIP SOIC
FB 1 3 I Feedback sense input pin. Connect to the midpoint of feedback divider to set
VOUT for ADJ version or connect this pin directly to the output capacitor for a
fixed output version.
NC 8, 6 1, 2, 7, 8, 9,
11, 13, 14 No internal connection, but must be soldered to PCB for best heat transfer.
ON/OFF 3 5 I Enable input to the voltage regulator. High = OFF and low = ON. Connect to
GND to enable the voltage regulator. Do not leave this pin float.
OUTPUT 7 12 O Emitter pin of the power transistor. This is a switching node. Attached this pin
to an inductor and the cathode of the external diode.
PWR_GND 4 6 Power ground pins. Connect to system ground and SIF GND, ground pins of
CIN and COUT. Path to CIN must be as short as possible.
SIG_GND 2 4 Signal ground pin. Ground reference for internal references and logic. Connect
to system ground.
VIN 5 10 I Supply input pin to collector pin of high-side transistor. Connect to power
supply and input bypass capacitors CIN. Path from VIN pin to high frequency
bypass CIN and PWR GND must be as short as possible.
4
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Maximum supply voltage LM2574 45 V
LM2574HV 63
ON/OFF pin input voltage –0.3 VIN V
Output voltage to ground, steady-state –1 V
Power dissipation Internally limited
Lead temperature, soldering (10 s) 260 °C
Maximum junction temperature 150 °C
Storage temperature, Tstg –65 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
Supply voltage LM2574 40 V
LM2574HV 60
TJTemperature –40 125 °C
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) The package thermal impedance is calculated in accordance with JESD 51-7.
(3) Thermal resistances were simulated on a 4-layer, JEDEC board.
6.4 Thermal Information
THERMAL METRIC(1)(2) LM2574, LM2574HV
UNITP (PDIP) NPA (SOIC)
8 PINS 14 PINS
RθJA Junction-to-ambient thermal resistance(3) 60.4 77.1 °C/W
RθJC(top) Junction-to-case (top) thermal resistance(3) 59.9 29.2 °C/W
RθJB Junction-to-board thermal resistance(3) 37.9 33.3 °C/W
ψJT Junction-to-top characterization parameter 17.1 2 °C/W
ψJB Junction-to-board characterization parameter 37.7 32.8 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance(3) °C/W
5
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
(1) All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature
extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
(2) The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated
output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power
dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2% (see Figure 6).
(3) Output pin sourcing current. No diode, inductor or capacitor connected to output pin.
(4) Feedback pin removed from output and connected to 0 V.
(5) Feedback pin removed from output and connected to 12 V for the adjustable, 3.3-V, and 5-V versions, and 25 V for the 12-V and 15-V
versions, to force the output transistor OFF.
(6) VIN = 40 V (60 V for high voltage version).
6.5 Electrical Characteristics for All Output Voltage Versions
TJ= 25°C, and MIN and MAX apply over full operating temperature range. VIN = 12 V for the 3.3-V, 5-V, and adjustable
version, VIN = 25 V for the 12-V version, and VIN = 30 V for the 15-V version, ILOAD = 100 mA (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN(1) TYP MAX(1) UNIT
IbFeedback bias current Adjustable version
only, VOUT = 5 V TJ= 25°C 50 100 nA
–40°C < TJ< 125°C 500
fOOscillator frequency See(2) TJ= 25°C 47 52 58 kHz
–40°C < TJ< 125°C 42 63
VSAT Saturation voltage IOUT = 0.5 A(3) TJ= 25°C 0.9 1.2 V
–40°C < TJ< 125°C 1.4
DC Maximum duty cycle (ON) See(4) 93% 98%
ICL Current limit Peak current(2)(3) 0.7 1 1.6 A
0.65 1.8
ILCurrent output leakage Output = 0 V 2 mA
Output = –1 V(5)(6) 7.5 30
IQQuiescent current See(5) 5 10 mA
ISTBY Standby quiescent current ON/OFF pin = 5 V (OFF) 50 200 μA
ON/OFF CONTROL (SEE Figure 27)
VIH ON/OFF pin logic input level VOUT = 0 V TJ= 25°C 2.2 1.4 V
–40°C < TJ< 125°C 2.4
VIL VOUT = Nominal output
voltage TJ= 25°C 1.2 1 V
–40°C < TJ< 125°C 0.8
IHON/OFF pin input current ON/OFF pin = 5 V (OFF) 12 30 μA
IIL ON/OFF pin = 0 V (ON) 0 10 μA
(1) Test Circuit in Figure 22 and Figure 27.
(2) All limits specified at room temperature and at temperature extremes . All room temperature limits are 100% production tested. All limits
at temperature extremes are specified via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to
calculate Average Outgoing Quality Level.
6.6 Electrical Characteristics 3.3-V Version
TJ= 25°C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted).
PARAMETER(1) TEST CONDITIONS MIN(2) TYP MAX(2) UNIT
VOUT Output voltage
VIN = 12 V, ILOAD = 100 mA 3.234 3.3 3.366
V
LM2574, 4.75 V VIN 40 V,
0.1 A ILOAD 0.5 A TJ= 25°C 3.168 3.3 3.432
40°C TJ125°C 3.135 3.465
LM2574HV, 4.75 V VIN 60 V,
0.1 A ILOAD 0.5 A TJ= 25°C 3.168 3.3 3.45
40°C TJ125°C 3.135 3.482
ηEfficiency VIN = 12 V, ILOAD = 0.5 A 72%
6
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
(1) Test circuit in Figure 22 and Figure 27.
(2) All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature
extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
6.7 Electrical Characteristics 5-V Version
TJ= 25°C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted).
PARAMETER(1) TEST CONDITIONS MIN TYP(2) MAX(2) UNIT
VOUT Output voltage
VIN = 12 V, ILOAD = 100 mA 4.9 5 5.1
V
LM2574, 7 V VIN 40 V,
0.1 A ILOAD 0.5 A TJ= 25°C 4.8 5 5.2
40°C TJ125°C 4.75 5.25
LM2574HV, 7 V VIN 60 V,
0.1 A ILOAD 0.5 A TJ= 25°C 4.8 5 5.225
40°C TJ125°C 4.75 5.275
ηEfficiency VIN = 12 V, ILOAD = 0.5 A 77%
(1) Test circuit in Figure 22 and Figure 27.
(2) All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature
extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
6.8 Electrical Characteristics 12-V Version
TJ= 25°C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted).
PARAMETER(1) CONDITIONS MIN TYP(2) MAX(2) UNIT
VOUT Output voltage
VIN = 25 V, ILOAD = 100 mA 11.76 12 12.24
V
LM2574, 15 V VIN 40 V,
0.1 A ILOAD 0.5 A TJ= 25°C 11.52 12 12.48
40°C TJ125°C 11.4 12.6
LM2574HV, 15 V VIN 60 V,
0.1 A ILOAD 0.5 A TJ= 25°C 11.52 12 12.54
40°C TJ125°C 11.4 12.66
ηEfficiency VIN = 15 V, ILOAD = 0.5 A 88%
(1) Test circuit in Figure 22 and Figure 27.
(2) All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature
extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
6.9 Electrical Characteristics 15-V Version
TJ= 25°C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted).
PARAMETER(1) TEST CONDITIONS MIN TYP(2) MAX(2) UNIT
VOUT Output voltage
VIN = 30 V, ILOAD = 100 mA 14.7 15 15.3
V
LM2574, 18 V VIN 40 V,
0.1A ILOAD 0.5 A TJ= 25°C 14.4 15 15.6
40°C TJ125°C 14.25 15.75
LM2574HV, 18 V VIN 60 V,
0.1 A ILOAD 0.5 A TJ= 25°C 14.4 15 15.68
40°C TJ125°C 14.25 15.83
ηEfficiency VIN = 18 V, ILOAD = 0.5 A 88%
7
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
(1) Test circuit in Figure 22 and Figure 27.
(2) All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature
extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate
Average Outgoing Quality Level.
6.10 Electrical Characteristics Adjustable Version
TJ= 25°C, and all MIN and MAX apply over full operating temperature range. VIN = 12 V, ILOAD = 100 mA (unless otherwise
noted).
PARAMETER(1) TEST CONDITIONS MIN TYP(2) MAX(2) UNIT
VFB Feedback voltage
VIN = 12 V, ILOAD = 100 mA 1.217 1.23 1.243
V
LM2574, 7 V VIN 40 V,
0.1 A ILOAD 0.5 A,
VOUT programmed for 5 V
TJ= 25°C 1.193 1.23 1.267
40°C TJ125°C 1.18 1.28
LM2574HV, 7 V VIN 60 V,
0.1 A ILOAD 0.5 A,
VOUT programmed for 5 V
TJ= 25°C 1.193 1.23 1.273
40°C TJ125°C 1.18 1.286
ηEfficiency VIN = 12 V, VOUT = 5 V, ILOAD = 0.5 A 77%
8
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
6.11 Typical Characteristics
See Figure 27.
Figure 1. Normalized Output Voltage Figure 2. Line Regulation
Figure 3. Dropout Voltage Figure 4. Current Limit
Figure 5. Supply Current Figure 6. Standby Quiescent Current
9
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Typical Characteristics (continued)
See Figure 27.
Figure 7. Oscillator Frequency Figure 8. Switch Saturation Voltage
Figure 9. Efficiency Figure 10. Minimum Operating Voltage
Figure 11. Supply Current versus Duty Cycle Figure 12. Feedback Voltage versus Duty Cycle
10
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Typical Characteristics (continued)
See Figure 27.
Figure 13. Feedback Pin Current Figure 14. Junction-to-Ambient Thermal Resistance
Unregulated
DC Input
CIN
+
2
Feedback
1
5
VIN
Internal
Regulator ON / OFF
Signal
GND
+
±
+
±
1.23 V
BAND ± GAP
REFRENCE Reset Thermal
Shutdown
Current
Limit
52 kHz
OSCILLATOR
Compatator
Fixed Gain
Error Amp
R2
R1
ON / OFF
0.5 Amp
Switch
3
7
4
DRIVER
Pwr Gnd
Output
+
COUT
D1
L1
L
O
A
D
VOUT
11
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
The LM2574 SIMPLE SWITCHER®regulator is an easy-to-use, non-synchronous, step-down DC-DC converter
with a wide input voltage range from 40 V to up to 60 V for a HV version. It is capable of delivering up to 0.5-A
DC load current with excellent line and load regulation. These devices are available in fixed output voltages of
3.3 V, 5 V, 12 V, 15 V, and an adjustable output version. The family requires few external components and the
pin arrangement was designed for simple, optimum PCB layout.
7.2 Functional Block Diagram
Note: Pin numbers are for the 8-pin PDIP package
R1 = 1 k
3.3 V, R2 = 1.7 k
5 V, R2 = 3.1 k
12 V, R2 = 8.84 k
15 V, R2 = 11.3 k
For adjustable version,
R1 = Open, R2 = 0 Ω
7.3 Feature Description
7.3.1 Current Limit
The LM2574 device has current limiting to prevent the switch current from exceeding safe values during an
accidental overload on the output. This value (ICL) can be found in the Electrical Characteristics for All Output
Voltage Versions.
7.3.2 Undervoltage Lockout
In some applications, it is desirable to keep the regulator off until the input voltage reaches a certain threshold.
An undervoltage lockout circuit that accomplishes this task is shown in Figure 15 while Figure 16 shows the
same circuit applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage
reaches a predetermined level in Equation 1.
VTH VZ1 + 2 VBE (1)
12
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Feature Description (continued)
Note: Complete circuit not shown (see Figure 20).
Note: Pin numbers are for 8-pin PDIP package.
Figure 15. Undervoltage Lockout for Buck Circuit
Note: Complete circuit not shown (see Figure 20).
Note: Pin numbers are for 8-pin PDIP package.
Figure 16. Undervoltage Lockout for Buck-Boost Circuit
7.3.3 Delayed Start-up
The ON/OFF pin can be used to provide a delayed start-up feature as shown in Figure 17. With an input voltage
of 20 V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit
begins switching. Increasing the RC time constant can provide longer delay times, but excessively large RC time
constants can cause problems with input voltages that are high in 60-Hz or 120-Hz ripple, by coupling the ripple
into the ON/OFF pin.
7.3.4 Adjustable Output, Low-Ripple Power Supply
A 500-mA power supply that features an adjustable output voltage is shown in Figure 18. An additional L-C filter
that reduces the output ripple by a factor of 10 or more is included in this circuit.
13
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Feature Description (continued)
Note: Complete circuit not shown.
Note: Pin numbers are for 8-pin PDIP package.
Figure 17. Delayed Start-up
Note: Pin numbers are for 8-pin PDIP package.
Figure 18. 1.2-V to 55-V Adjustable 500-mA Power Supply With Low-Output Ripple
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The ON/OFF pin provides electrical ON and OFF control for the LM2574. When the voltage of this pin is higher
than 1.4 V, the device is shutdown mode. The typical standby current in this mode is 50 μA.
7.4.2 Active Mode
When the voltage of the ON/OFF pin is below 1.2 V, the device starts switching and the output voltage rises until
it reaches a normal regulation voltage.
OUT
ON
OUT IN
V
t
T V V
=
+
ON
LOAD
t
1.2 I
T
´ ´
14
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Input Capacitor (CIN)
To maintain stability, the regulator input pin must be bypassed with at least a 22-μF electrolytic capacitor. The
leads of the capacitor must be kept short, and located near the regulator.
If the operating temperature range includes temperatures below 25°C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower
temperatures and age. Paralleling a ceramic or solid tantalum capacitor increases the regulator stability at cold
temperatures. For maximum capacitor operating lifetime, the RMS ripple current rating of the capacitor must be
greater than Equation 2.
where
for a buck regulator
for a buck-boost regulator (2)
8.1.2 Inductor Selection
All switching regulators have two basic modes of operation: continuous and discontinuous. The difference
between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a
period of time in the normal switching cycle. Each mode has distinctively different operating characteristics,
which can affect the regulator performance and requirements.
The LM2574 (or any of the SIMPLE SWITCHER family) can be used for both continuous and discontinuous
modes of operation.
In many cases, the preferred mode of operation is in the continuous mode. It offers better load regulation, lower
peak switch, inductor, and diode currents, and can have lower output ripple voltage. It does require relatively
large inductor values to keep the inductor current flowing continuously, especially at low output load currents.
To simplify the inductor selection process, an inductor selection guide (nomograph) was designed. This guide
assumes continuous mode operation, and selects an inductor that allows a peak-to-peak inductor ripple current
(ΔIIND) to be a certain percentage of the maximum design load current. In the LM2574 SIMPLE SWITCHER, the
peak-to-peak inductor ripple current percentage (of load current) is allowed to change as different design load
currents are selected. By allowing the percentage of inductor ripple current to increase for lower current
applications, the inductor size and value can be kept relatively low.
8.1.3 Inductor Ripple Current
When the switcher is operating in the continuous mode, the inductor current waveform ranges from a triangular
to a sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage,
the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls,
the entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the
DC load current (in the buck regulator configuration).
IND
I212 106 mA
2 2
D
= = =
IND
LOAD
I212
I 0.4 A 506 mA
2 2
D
æ ö æ ö
= + = + =
ç ÷ ç ÷
è ø
è ø
15
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
If the load current drops to a low enough level, the bottom of the sawtooth current waveform reaches zero, and
the switcher changes to a discontinuous mode of operation. This is a perfectly acceptable mode of operation.
Any buck switching regulator (no matter how large the inductor value is) is forced to run discontinuous if the load
current is light enough.
The curve shown in Figure 19 illustrates how the peak-to-peak inductor ripple current (ΔIIND) is allowed to change
as different maximum load currents are selected, and also how it changes as the operating point varies from the
upper border to the lower border within an inductance region (see the Inductor Selection section).
Figure 19. Inductor Ripple Current (ΔiIND) Range
Consider the following example:
VOUT =5Vat0.4A
VIN = 10-V minimum up to 20-V maximum
The selection guide in Figure 24 shows that for a 0.4-A load current, and an input voltage range between 10 V
and 20 V, the inductance region selected by the guide is 330 μH. This value of inductance allows a peak-to-peak
inductor ripple current (ΔIIND) to flow that is a percentage of the maximum load current. For this inductor value,
the ΔIIND also varies depending on the input voltage. As the input voltage increases to 20 V, it approaches the
upper border of the inductance region, and the inductor ripple current increases. Referring to the curve in
Figure 19, it can be seen that at the 0.4-A load current level, and operating near the upper border of the 330-μH
inductance region, the ΔIIND is 53% of 0.4 A, or 212 mAp-p.
This ΔIIND is important because from this number the peak inductor current rating can be determined, the
minimum load current required before the circuit goes to discontinuous operation, and also, knowing the ESR of
the output capacitor, the output ripple voltage can be calculated, or conversely, measuring the output ripple
voltage and knowing the ΔIIND, the ESR can be calculated.
From the previous example, the peak-to-peak inductor ripple current (ΔIIND) = 212 mAp-p. When the ΔIND value is
known, the following three formulas can be used to calculate additional information about the switching regulator
circuit:
1. Peak inductor or peak switch current in Equation 3.
(3)
2. Minimum load current before the circuit becomes discontinuous in Equation 4.
(4)
3. Output ripple voltage = (ΔIIND) × (ESR of COUT)
16
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value
chosen is prohibitively high, the designer must investigate the possibility of discontinuous operation.
Inductors are available in different styles such as pot core, toroid, E-frame, bobbin core, and so forth, as well as
different core materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists
of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor, but because
the magnetic flux is not completely contained within the core, it generates more electro-magnetic interference
(EMI). This EMl can cause problems in sensitive circuits, or can give incorrect scope readings because of
induced voltages in the scope probe.
The inductors listed in the selection chart include powdered iron toroid for Pulse Engineering and ferrite bobbin
core for Renco.
An inductor must not be operated beyond its maximum rated current because it can saturate. When an inductor
begins to saturate, the inductance decreases rapidly and the inductor begins to look mainly resistive (the DC
resistance of the winding). This can cause the inductor current to rise very rapidly and affects the energy storage
capabilities of the inductor and can cause inductor overheating. Different inductor types have different saturation
characteristics, and consider this when selecting an inductor. The inductor manufacturers' data sheets include
current and energy limits to avoid inductor saturation.
8.1.4 Output Capacitor
An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor must be
located near the LM2574 using short PCB traces. Standard aluminum electrolytics are usually adequate, but low
ESR types are recommended for low output ripple voltage and good stability. The ESR of a capacitor depends
on many factors, some which are:
The value
The voltage rating
The physical size
The type of construction
In general, low-value or low-voltage (less than 12 V) electrolytic capacitors usually have higher ESR numbers.
The amount of output ripple voltage is primarily a function of the equivalent series resistance (ESR ) of the output
capacitor and the amplitude of the inductor ripple current, ΔIIND (see the Inductor Ripple Current (ΔiIND)section).
The lower capacitor values (100 μF to 330 μF) allows typically 50 mV to 150 mV of output ripple voltage, while
larger-value capacitors reduce the ripple to approximately 20 mV to 50 mV (as seen in Equation 5).
Output Ripple Voltage = (ΔIIND) (ESR of COUT) (5)
To further reduce the output ripple voltage, several standard electrolytic capacitors can be paralleled, or a higher-
grade capacitor can be used. Such capacitors are often called high-frequency, low-inductance, or low-ESR.
These reduce the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode, reducing
the ESR below 0.03 Ωcan cause instability in the regulator.
Tantalum capacitors can have a very low ESR, and must be carefully evaluated if it is the only output capacitor.
Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum
electrolytics, with the tantalum making up 10% or 20% of the total capacitance.
The ripple current rating of the capacitor at 52 kHz must be at least 50% higher than the peak-to-peak inductor
ripple current.
8.1.5 Catch Diode
Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode
must be located close to the LM2574 using short leads and short printed-circuit traces.
17
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency,
especially in low output voltage switching regulators (less than 5 V). Fast-recovery, high-efficiency, or ultra-fast
recovery diodes are also suitable, but some types with an abrupt turnoff characteristic can cause instability and
EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60-Hz diodes
(for example, 1N4001 or 1N5400, and so forth) are also not suitable. See Table 1 for Schottky and soft fast-
recovery diode selection guide.
Table 1. Diode Selection Guide
VR1-A DIODES
SCHOTTKY FAST RECOVERY
20 V 1N5817
SR102
MBR120P
30 V
1N5818
SR103
11DQ03
MBR130P
10JQ030
The following diodes are all rated to 100 V
11DF1
10JF1
MUR110
HER102
40 V
1N5819
SR104
11DQ04
11JQ04
MBR140P
50 V MBR150
SR105
11DQ05
11JQ05
60 V MBR160
SR106
11DQ06
11JQ06
90 V 11DQ09
8.1.6 Output Voltage Ripple and Transients
The output voltage of a switching power supply contains a sawtooth ripple voltage at the switcher frequency,
typically about 1% of the output voltage, and can also contain short voltage spikes at the peaks of the sawtooth
waveform.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output
capacitor (see the Inductor Selection section).
The voltage spikes are present because of the fast switching action of the output switch, and the parasitic
inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can
be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, as well as the scope
probe used to evaluate these transients, all contribute to the amplitude of these spikes.
An additional small LC filter (20 μH and 100 μF) can be added to the output (as shown in Figure 18) to further
reduce the amount of output ripple and transients. A 10 × reduction in output ripple voltage and transients is
possible with this filter.
8.1.7 Feedback Connection
The LM2574 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching
power supply. When using the adjustable version, physically locate both output voltage programming resistors
near the LM2574 to avoid picking up unwanted noise. Avoid using resistors greater than 100 kΩbecause of the
increased chance of noise pickup.
( )
LOAD IN OUT IN OUT
P
IN IN OUT 1 OSC
I V V V V 1
I
V V V 2 L f
´ + ´
» + ´
+ ´ ´
18
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8.1.8 ON/OFF Input
For normal operation, the ON/OFF pin must be grounded or driven with a low-level TTL voltage (typically less
than 1.6 V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The
ON/OFF pin can be safely pulled up to +VIN without a resistor in series with it. The ON/OFF pin must not be left
open.
8.1.9 Additional Applications
8.1.9.1 Inverting Regulator
Figure 20 shows a LM2574-12 in a buck-boost configuration to generate a negative 12-V output from a positive
input voltage. This circuit bootstraps the ground pin of the regulator to the negative output voltage, then by
grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to 12 V.
Note: Pin numbers are for the 8-pin PDIP package.
Figure 20. Inverting Buck-Boost Develops, 12 V
For an input voltage of 8 V or more, the maximum available output current in this configuration is approximately
100 mA. At lighter loads, the minimum input voltage required drops to approximately 4.7 V.
The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus
lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than
the standard buck-mode regulator, which can overload an input power source with a current limit less than
0.6 A. Using a delayed turnon or an undervoltage lockout circuit (described in the Negative Boost Regulator
section) would allow the input voltage to rise to a high enough level before the switcher would be allowed to turn
on.
Because of the structural differences between the buck and the buck-boost regulator topologies, the design
procedure can not be used to select the inductor or the output capacitor. The recommended range of inductor
values for the buck-boost design is between 68 μH and 220 μH, and the output capacitor values must be larger
than what is normally required for buck designs. Low-input voltages or high-output currents require a large value
output capacitor (in the thousands of micro Farads).
The peak inductor current, which is the same as the peak switch current, can be calculated from Equation 6.
where
fosc = 52 kHz. Under normal continuous inductor current operating conditions, the minimum VIN represents the
worst case. Select an inductor that is rated for the peak current anticipated. (6)
Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage.
For a 12-V output, the maximum input voltage for the LM2574 is 28 V, or 48 V for the LM2574HV.
19
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
8.1.9.2 Negative Boost Regulator
Another variation on the buck-boost topology is the negative boost configuration. The circuit in Figure 21 accepts
an input voltage ranging from 5 V to 12 V and provides a regulated 12-V output. Input voltages greater than
12 V causes the output to rise greater than 12 V, but does not damage the regulator.
Note: Pin numbers are for 8-pin PDIP package.
Figure 21. Negative Boost
Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low
input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also,
boost regulators cannot provide current-limiting load protection in the event of a shorted load, so some other
means (such as a fuse) may be necessary.
8.2 Typical Applications
8.2.1 Fixed Output Voltage Applications
CIN: 22 μF, 75 V
Aluminum electrolytic
COUT: 220 μF, 25 V
Aluminum electrolytic
D1: Schottky, 11DQ06
L1: 330 μH, 52627
(for 5 V in, 3.3 V out, use
100 μH, RL-1284-100)
R1: 2k, 0.1%
R2: 6.12k, 0.1%
Figure 22. Fixed Output Voltage Versions
20
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Typical Applications (continued)
8.2.1.1 Design Requirements
The design requirements for the fixed output voltage application are provided in Table 2.
Table 2. Design Parameters
PARAMETER EXAMPLE VALUE
Regulated output voltage (3.3 V, 5 V, 12 V, or 15 V), VOUT 5 V
Maximum input voltage, VIN(Max) 15 V
Maximum load current, ILOAD(Max) 0.4 A
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LM2574 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
Run electrical simulations to see important waveforms and circuit performance
Run thermal simulations to understand board thermal performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
8.2.1.2.2 Inductor Selection (L1)
Select the correct inductor value selection guide from Figure 23,Figure 24,Figure 25,orFigure 26 (output
voltages of 3.3 V, 5 V, 12 V, or 15 V respectively).
From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and ILOAD(Max).
The inductance area intersected by the 15-V line and 0.4-A line is 330.
Select an appropriate inductor from Table 3. Part numbers are listed for three inductor manufacturers. The
inductor chosen must be rated for operation at the LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 × ILOAD. For additional inductor information, see the Inductor Selection section. The required inductor value
is 330 μH. From Table 3, choose Pulse Engineering PE-52627, Renco RL-1284-330, or NPI NP5920/5921.
21
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Table 3. Inductor Selection By Manufacturer's Part Number
INDUCTOR VALUE PULSE ENG. RENCO NPI
68 μH * RL-1284-68-43 NP5915
100 μH * RL-1284-100-43 NP5916
150 μH 52625 RL-1284-150-43 NP5917
220 μH 52626 RL-1284-220-43 NP5918/5919
330 μH 52627 RL-1284-330-43 NP5920/5921
470 μH 52628 RL-1284-470-43 NP5922
680 μH 52629 RL-1283-680-43 NP5923
1000 μH 52631 RL-1283-1000-43 *
1500 μH * RL-1283-1500-43 *
2200 μH * RL-1283-2200-43 *
8.2.1.2.3 Output Capacitor Selection (COUT)
The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output
voltage) a value between 100 μF and 470 μF is recommended. COUT = 100-μF to 470-μF standard aluminum
electrolytic.
The voltage rating of the capacitor must be at least 1.5 times greater than the output voltage. For a 5-V regulator,
a rating of at least 8 V is appropriate, and a 10-V or 15-V rating is recommended. Capacitor voltage rating =
20 V.
Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this reason it can be necessary
to select a capacitor rated for a higher voltage than would normally be needed.
22
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8.2.1.2.4 Catch Diode Selection (D1)
The catch-diode current rating must be at least 1.5 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to the
maximum current limit of the LM2574. The most stressful condition for this diode is an overload or shorted output
condition. For this example, a 1-A current rating is adequate.
The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 20-V
1N5817 or SR102 Schottky diode, or any of the suggested fast-recovery diodes shown in Table 1.
8.2.1.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 22-μF aluminum electrolytic capacitor located near the input and ground pins provides sufficient
bypassing.
8.2.2 Application Curves
Figure 23. 3.3-V LM2574HV Inductor Selection Guide Figure 24. 5-V LM2574HV Inductor Selection Guide
Figure 25. 12-V LM2574HV Inductor Selection Guide Figure 26. 15-V LM2574HV Inductor Selection Guide
OUT
2 1
REF
V24 V
R R 1 1 k 1
V 1.23 V
æ ö æ ö
= ´ - = ´ -
ç ÷ ç ÷
è ø
è ø
2
OUT
1
R
V 1.23 1
R
æ ö
= ´ +
ç ÷
è ø
OUT
2 1
REF
V
R R 1
V
æ ö
= ´ -
ç ÷
è ø
2
OUT REF
1
R
V V 1
R
æ ö
= ´ +
ç ÷
è ø
23
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
8.2.3 Adjustable Output Voltage Applications
Figure 27. Adjustable Output Voltage Version
8.2.3.1 Design Requirements
The design requirements for the fixed output voltage application are provided in Table 4.
Table 4. Design Parameters
PARAMETER EXAMPLE VALUE
Regulated output voltage, VOUT 24 V
Maximum input voltage, VIN(Max) 40 V
Maximum load current, ILOAD(Max) 0.4 A
Switching frequency, F 52 kHz
8.2.3.2 Detailed Design Procedure
8.2.3.2.1 Programming Output Voltage
Selecting R1 and R2, as shown in Figure 27.
Use Equation 7 to select the appropriate resistor values.
where
VREF = 1.23 V (7)
R1can be between 1 k and 5 k as in Equation 8. For best temperature coefficient and stability with time, use 1%
metal film resistors.
(8)
For this example, use Equation 9 and Equation 10.
select
R1 = 1 k (9)
(10)
R2= 1 k (19.511) = 18.51 k, closest 1% value is 18.7 k
OUT
40
C 13300 22.2 µF
24 1000
> ´ =
´
( )
( )( )
IN MAX
OUT
OUT
V
C 13300 µF
V L µH
³ ´ ´
( ) 24 1000
E T 40 24 185 V µs
40 52
´ = - ´ ´ = ´
( ) ( )( )
OUT
IN OUT
IN
V1000
E T V V V µs
V F kHz
´ = - ´ ´ ´
24
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8.2.3.2.2 Inductor Selection (L1)
Calculate the inductor Volt × microsecond constant, E × T (V × μs), from Equation 11.
(11)
For this example, calculate E × T (V × μs) using Equation 12.
(12)
Use the E × T value from the previous formula and match it with the E × T number on the vertical axis of the
inductor value selection guide shown in Figure 32. For this example, E × T = 185 V × μs.
On the horizontal axis, select the maximum load current, ILOAD(Max) = 0.4 A.
Identify the inductance region intersected by the E × T value and the maximum load current value, and note the
inductor value for that region, inductance region = 1000.
Select an appropriate inductor from Table 3. Part numbers are listed for three inductor manufacturers. The
inductor chosen must be rated for operation at the LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 × ILOAD. For additional inductor information, see the Inductor Selection section.
8.2.3.2.3 Output Capacitor Selection (COUT)
The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation, the capacitor must satisfy the requirement in Equation 13.
(13)
Equation 13 yields capacitor values between 5 μF and 1000 μF that satisfies the loop requirements for stable
operation. To achieve an acceptable output ripple voltage, (approximately 1% of the output voltage) and transient
response, the output capacitor may need to be several times larger than the above formula yields.
The voltage rating of the capacitor must be at last 1.5 times greater than the output voltage. For a 24-V regulator,
a rating of at least 35 V is recommended. Higher voltage electrolytic capacitors generally have lower ESR
numbers, and for this reason, it can be necessary to select a capacitor rate for a higher voltage than would
normally be needed.
(14)
However, for acceptable output ripple voltage select:
COUT 100 μF
COUT = 100 μF electrolytic capacitor
8.2.3.2.4 Catch Diode Selection (D1)
The catch-diode current rating must be at least 1.5 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to the
maximum current limit of the LM2574. The most stressful condition for this diode is an overload or shorted output
condition. Suitable diodes are shown in Table 1. For this example, a 1-A current rating is adequate.
The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 50-V
MBR150 or 11DQ05 Schottky diode, or any of the suggested fast-recovery diodes in Table 1.
8.2.3.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 22-μF aluminum electrolytic capacitor located near the input and ground pins provides sufficient
bypassing (see Table 1).
25
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
8.2.3.3 Application Curves
Output pin voltage, 10 V/div Horizontal time base
Inductor current, 0.2 A/div 5 μs/div
Output ripple voltage VOUT = 5 V
20 mV/div 500-mA load current
AC-coupled L = 330 Μh
Figure 28. Continuous Mode Switching Waveforms
Output pin voltage, 10 V/div Horizontal time base
Inductor current, 0.2 A/div 5 μs/div
Output ripple voltage VOUT = 5 V
20 mV/div 100-mA load current
AC-coupled L = 100 Μh
Figure 29. Discontinuous Mode Switching Waveforms
Output voltage, 50 V/div 500 mA load
AC-coupled L = 330 Μh
100-mA to 500-mA load pulse COUT = 300 Μf
Horizontal time base: 200 μs/div
Figure 30. Transient Response for
Continuous Mode Operation
Output voltage, 50 V/div, 250 mA load
AC-coupled L = 68 Μh
50-mA to 250-mA load pulse COUT = 470 Μf
Horizontal time base: 200 μs/div
Figure 31. Transient Response for
Discontinuous Mode Operation
Figure 32. Adjustable LM2574HV Inductor Selection Guide
26
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
9 Power Supply Recommendations
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, the
length of the leads indicated by heavy lines must be kept as short as possible. Single-point grounding (as
indicated) or ground plane construction must be used for best results. When using the adjustable version,
physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short.
10 Layout
10.1 Layout Guidelines
The layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise can turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in
the layout to minimize the effect of this switching noise.
The most important layout rule is to keep the AC current loops as small as possible. Figure 33 shows the current
flow in a buck converter. The top schematic shows a dotted line which represents the current flow during the top
switch ON-state. The middle schematic shows the current flow during the top switch OFF-state. The bottom
schematic shows the currents referred to as AC currents. These AC currents are the most critical because they
are changing in a very short time period. The dotted lines of the bottom schematic are the traces to keep as short
and wide as possible. This also yields a small loop area reducing the loop inductance. To avoid functional
problems due to layout, review the PCB layout example. Best results are achieved if the placement of the
LM2574 device, the bypass capacitor, the Schottky diode, RFBB, RFBT, and the inductor are placed as shown in
the example. In the layout shown, R1 = RFBB and R2 = RFBT. TI also recommends using 2-oz. copper boards
or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See the application
note AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines for more information.
Figure 33. Buck Converter Current Flow
27
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
10.2 Layout Example
Figure 34. LM2574 Adjustable Output Voltage Layout
10.3 Grounding
The 8-pin molded PDIP and the 14-pin SOIC package have separate power and signal ground pins. Both ground
pins must be soldered directly to wide printed-circuit board copper traces to assure low inductance connections
and good thermal properties.
10.4 Thermal Considerations
The 8-pin PDIP (P) package and the 14-pin SOIC (NPA) package are molded plastic packages with solid copper
lead frames. The copper lead frame conducts the majority of the heat from the die, through the leads, to the
printed-circuit board copper, which acts as the heat sink. For best thermal performance, wide copper traces must
be used, and all ground and unused pins must be soldered to generous amounts of printed-circuit board copper,
such as a ground plane. Large areas of copper provide the best transfer of heat (lower thermal resistance) to the
surrounding air, and even double-sided or multilayer boards provide better heat paths to the surrounding air.
Unless the power levels are small, using a socket for the 8-pin package is not recommended because of the
additional thermal resistance it introduces, and the resultant higher junction temperature.
Because of the 0.5-A current rating of the LM2574, the total package power dissipation for this switcher is quite
low, ranging from approximately 0.1 W up to 0.75 W under varying conditions. In a carefully engineered printed-
circuit board, both the P and the NPA package can easily dissipate up to 0.75 W, even at ambient temperatures
of 60°C, and still keep the maximum junction temperature less than 125°C.
A curve, Figure 14, displaying thermal resistance versus PCB area for the two packages is shown in the Typical
Characteristics.
These thermal resistance numbers are approximate, and there can be many factors that affect the final thermal
resistance. Some of these factors include board size, shape, thickness, position, location, and board
temperature. Other factors are, the area of printed-circuit copper, copper thickness, trace width, multi-layer,
single- or double-sided, and the amount of solder on the board. The effectiveness of the PCB to dissipate heat
also depends on the size, number and spacing of other components on the board. Furthermore, some of these
components, such as the catch diode and inductor generate some additional heat. Also, the thermal resistance
decreases as the power level increases because of the increased air current activity at the higher power levels,
and the lower surface to air resistance coefficient at higher temperatures.
The data sheet thermal resistance curves can estimate the maximum junction temperature based on operating
conditions. ln addition, the junction temperature can be estimated in actual circuit operation by using
Equation 15.
Tj= Tcu + (θj-cu × PD) (15)
OUT
D IN S LOAD SAT
IN
V
P V I I V
V
= ´ + ´ ´
28
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Thermal Considerations (continued)
With the switcher operating under worst case conditions and all other components on the board in the intended
enclosure, measure the copper temperature (Tcu ) near the IC. This can be done by temporarily soldering a small
thermocouple to the PCB copper near the IC, or by holding a small thermocouple on the PCB copper using
thermal grease for good thermal conduction.
The thermal resistance (θj-cu) for the two packages is:
θj-cu = 42°C/W for the P-8 package
θj-cu = 52°C/W for the NPA-14 package
The power dissipation (PD) for the IC could be measured, or it can be estimated by using Equation 16.
where
ISis obtained from the typical supply current curve (adjustable version use the supply current vs duty cycle
curve) (16)
OUT OUT
IN OUT LOSS
P P
P P P
h = =
+
OUT
ON
OUT IN
V
t
D
T V V
= =
+
ON OUT
IN
t V
D
T V
= =
29
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.1.2 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LM2574 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
Run electrical simulations to see important waveforms and circuit performance
Run thermal simulations to understand board thermal performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.1.3 Device Nomenclature
11.1.3.1 Buck Regulator
A switching regulator topology in which a higher voltage is converted to a lower voltage. Also known as a step-
down switching regulator.
11.1.3.2 Buck-Boost Regulator
A switching regulator topology in which a positive voltage is converted to a negative voltage without a
transformer.
11.1.3.3 Duty Cycle (D)
The ratio of the ON-time of the output switch to the oscillator period calculated with Equation 17 for buck
regulators and Equation 18 for buck-boost regulators.
(17)
(18)
11.1.3.4 Catch Diode or Current Steering Diode
This diode provides a return path for the load current when the LM2574 switch is OFF.
In terms of efficiency (η), the proportion of input power actually delivered to the load calculated with Equation 19.
(19)
30
LM2574
,
LM2574HV
SNVS104F JUNE 1999REVISED MAY 2020
www.ti.com
Product Folder Links: LM2574 LM2574HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Device Support (continued)
11.1.3.5 Capacitor Equivalent Series Resistance (ESR)
The purely resistive component of a real capacitor's impedance (see Figure 35) can causes power loss resulting
in capacitor heating, which directly affects the operating lifetime of the capacitor. When used as a switching
regulator output filter, higher ESR values result in higher output ripple voltages.
Figure 35. Simple Model Of A Real Capacitor
Most standard aluminum electrolytic capacitors in the 100 μF to 1000 μF range have 0.5-Ωto 0.1-ΩESR. Higher-
grade capacitors (low-ESR,high-frequency, or low-inductance) in the 100 μF to 1000 μF range generally have
ESR of less than 0.15 Ω.
11.1.3.6 Equivalent Series Inductance (ESL)
The pure inductance component of a capacitor is seen in Figure 35. The amount of inductance is determined to a
large extent on the capacitor's construction. In a buck regulator, this unwanted inductance causes voltage spikes
to appear on the output.
11.1.3.7 Output Ripple Voltage
The AC component of the output voltage of the switching regulator is usually dominated by the output capacitor's
ESR multiplied by the inductor's ripple current (ΔIIND). The peak-to-peak value of this sawtooth ripple current can
be determined by reading Inductor Ripple Current (ΔiIND).
11.1.3.8 Capacitor Ripple Current
The RMS value of the maximum allowable alternating current at which a capacitor can be operated continuously
at a specified temperature.
11.1.3.9 Standby Quiescent Current (ISTBY)
Supply current required by the LM2574 when in the standby mode (ON/OFF pin is driven to TTL-high voltage,
thus turning the output switch OFF).
11.1.3.10 Inductor Ripple Current (ΔiIND)
The peak-to-peak value of the inductor current waveform, typically a sawtooth waveform when the regulator is
operating in the continuous mode (vs. discontinuous mode).
11.1.3.11 Continuous and Discontinuous Mode Operation
These mode operations relate to the inductor current. In the continuous mode, the inductor current is always
flowing and never drops to zero, versus the discontinuous mode, where the inductor current drops to zero for a
period of time in the normal switching cycle.
11.1.3.12 Inductor Saturation
The condition which exists when an inductor cannot hold any more magnetic flux. When an inductor saturates,
the inductor appears less inductive and the resistive component dominates. Inductor current is then limited only
by the DC resistance of the wire and the available source current.
11.1.3.13 Operating Volt Microsecond Constant (E × Top)
The product (in VoIt × μs) of the voltage applied to the inductor and the time the voltage is applied. This E × Top
constant is a measure of the energy handling capability of an inductor and is dependent upon the type of core,
the core area, the number of turns, and the duty cycle.
31
LM2574
,
LM2574HV
www.ti.com
SNVS104F JUNE 1999REVISED MAY 2020
Product Folder Links: LM2574 LM2574HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation see the following:
Texas Instruments, AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines Application Report (SNVA054)
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
WEBENCH, SIMPLE SWITCHER are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.7 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Apr-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2574HVM-12/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-12 P+
LM2574HVM-15 NRND SOIC NPA 14 50 TBD Call TI Call TI -40 to 125 LM2574HVM
-15 P+
LM2574HVM-15/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-15 P+
LM2574HVM-3.3/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-3.3 P+
LM2574HVM-5.0 NRND SOIC NPA 14 50 TBD Call TI Call TI -40 to 125 LM2574HVM
-5.0 P+
LM2574HVM-5.0/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-5.0 P+
LM2574HVM-ADJ/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-ADJ P+
LM2574HVMX-12/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-12 P+
LM2574HVMX-15/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-15 P+
LM2574HVMX-3.3/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-4-260C-72 HR -40 to 125 LM2574HVM
-3.3 P+
LM2574HVMX-5.0 NRND SOIC NPA 14 1000 TBD Call TI Call TI -40 to 125 LM2574HVM
-5.0 P+
LM2574HVMX-5.0/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-5.0 P+
LM2574HVMX-ADJ/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574HVM
-ADJ P+
LM2574HVN-12/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574HVN
-12 P+
LM2574HVN-15/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2574HVN
-15 P+
LM2574HVN-5.0/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2574HVN
-5.0 P+
LM2574HVN-ADJ/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2574HVN
-ADJ P+
PACKAGE OPTION ADDENDUM
www.ti.com 17-Apr-2020
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2574M-12/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-12 P+
LM2574M-3.3/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-3.3 P+
LM2574M-5.0 NRND SOIC NPA 14 50 TBD Call TI Call TI -40 to 125 LM2574M
-5.0 P+
LM2574M-5.0/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-5.0 P+
LM2574M-ADJ NRND SOIC NPA 14 50 TBD Call TI Call TI -40 to 125 LM2574M
-ADJ P+
LM2574M-ADJ/NOPB ACTIVE SOIC NPA 14 50 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-ADJ P+
LM2574MX-12/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-12 P+
LM2574MX-3.3/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-4-260C-72 HR -40 to 125 LM2574M
-3.3 P+
LM2574MX-5.0/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-5.0 P+
LM2574MX-ADJ/NOPB ACTIVE SOIC NPA 14 1000 Green (RoHS
& no Sb/Br) SN Level-3-260C-168 HR -40 to 125 LM2574M
-ADJ P+
LM2574N-12/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N
-12 P+
LM2574N-3.3/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N
-3.3 P+
LM2574N-5.0/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N
-5.0 P+
LM2574N-ADJ/NOPB ACTIVE PDIP P 8 40 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2574N
-ADJ P+
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Apr-2020
Addendum-Page 3
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2574HVMX-12/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574HVMX-15/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574HVMX-3.3/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574HVMX-5.0 SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574HVMX-5.0/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574HVMX-ADJ/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574MX-12/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574MX-3.3/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574MX-5.0/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
LM2574MX-ADJ/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 17-Apr-2020
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2574HVMX-12/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574HVMX-15/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574HVMX-3.3/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574HVMX-5.0 SOIC NPA 14 1000 367.0 367.0 38.0
LM2574HVMX-5.0/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574HVMX-ADJ/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574MX-12/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574MX-3.3/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574MX-5.0/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
LM2574MX-ADJ/NOPB SOIC NPA 14 1000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 17-Apr-2020
Pack Materials-Page 2
MECHANICAL DATA
NPA0014B
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated