LT1934/LT1934-1 Micropower Step-Down Switching Regulators in ThinSOT and DFN FEATURES DESCRIPTION n The LT (R)1934 is a micropower step-down DC/DC converter with internal 400mA power switch, packaged in a low profile (1mm) ThinSOT. With its wide input range of 3.2V to 34V, the LT1934 can regulate a wide variety of power sources, from 4-cell alkaline batteries and 5V logic rails to unregulated wall transformers and lead-acid batteries. Quiescent current is just 12A and a zero current shutdown mode disconnects the load from the input source, simplifying power management in battery-powered systems. Burst Mode(R) operation and the low drop internal power switch result in high efficiency over a broad range of load current. n n n n n n n n Wide Input Voltage Range: 3.2V to 34V Micropower Operation: IQ = 12A 5V at 250mA from 6.5V to 34V Input (LT1934) 5V at 60mA from 6.5V to 34V Input (LT1934-1) 3.3V at 250mA from 4.5V to 34V Input (LT1934) 3.3V at 60mA from 4.5V to 34V Input (LT1934-1) Low Shutdown Current: <1A Low VCESAT Switch: 200mV at 300mA Low Profile (1mm) SOT-23 (ThinSOTTM) and (2mm x 3mm x 0.8mm) 6-Pin DFN Package APPLICATIONS n n n n n The LT1934 provides up to 300mA of output current. The LT1934-1 has a lower current limit, allowing optimum choice of external components when the required output current is less than 60mA. Fast current limiting protects the LT1934 and external components against shorted outputs, even at 34V input. Wall Transformer Regulation Automotive Battery Regulation Standby Power for Portable Products Distributed Supply Regulation Industrial Control Supplies L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION 3.3V Step-Down Converter Efficiency 100 D2 VIN 4.5V TO 34V ON OFF VIN C2 2.2F 90 L1 47H VOUT 3.3V 250mA SW D1 LT1934 SHDN 10pF 1M + FB GND C1: SANYO 4TPB100M C2: TAIYO YUDEN GMK325BJ225MN D1: ON SEMICONDUCTOR MBR0540 D2: CENTRAL CMDSH-3 L1: SUMIDA CDRH4D28-470 C1 100F 604k EFFICIENCY (%) 0.22F BOOST LT1934 VIN = 12V VOUT = 5V 80 VOUT = 3.3V 70 60 1934 TA01 50 0.1 1 10 100 LOAD CURRENT (mA) 1934 TA02 1934fe 1 LT1934/LT1934-1 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Voltage (VIN) ................................................... 34V BOOST Pin Voltage ................................................. 40V BOOST Pin Above SW Pin........................................ 20V SHDN Pin ................................................................. 34V FB Voltage .................................................................. 6V SW Voltage ............................................................... VIN Operating Temperature Range (Note 2) LT1934E/LT1934E-1 .............................- 40C to 85C LT1934I/LT1934I-1 .............................- 40C to 125C Maximum Junction Temperature .......................... 125C Storage Temperature Range...................- 65C to 150C Lead Temperature (Soldering, 10 sec) TSOT-23 ............................................................ 300C PIN CONFIGURATION TOP VIEW TOP VIEW 6 FB BOOST 1 BOOST 1 GND 2 FB 3 6 SW SW 2 5 VIN 4 SHDN 7 VIN 3 S6 PACKAGE 6-LEAD PLASTIC TSOT-23 TJMAX = 125C, JA = 250C/ W, JC = 102C/W 5 GND 4 SHDN DCB PACKAGE 6-LEAD (2mm s 3mm) PLASTIC DFN JA = 73.5C/ W, JC = 12C/W EXPOSED PAD (PIN 7) IS GND, MUST BE SOLDEDED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL S6 PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1934ES6#PBF LT1934ES6#TRPBF LTXP 6-Lead Plastic TSOT-23 -40C to 85C LT1934ES6-1#PBF LT1934ES6-1#TRPBF LTF8 6-Lead Plastic TSOT-23 -40C to 85C LT1934IS6#PBF LT1934IS6#TRPBF LTAJB 6-Lead Plastic TSOT-23 -40C to 125C LT1934IS6-1#PBF LT1934IS6-1#TRPBF LTAJC 6-Lead Plastic TSOT-23 -40C to 125C LT1934IDCB#PBF LT1934IDCB#TRPBF LCFZ 6-Lead (2mm x 3mm) Plastic DFN -40C to 125C LT1934EDCB#PBF LT1934EDCB#TRPBF LCFZ 6-Lead (2mm x 3mm) Plastic DFN -40C to 85C LT1934IDCB-1#PBF LT1934IDCB-1#TRPBF LDHC 6-Lead (2mm x 3mm) Plastic DFN -40C to 125C LT1934EDCB-1#PBF LT1934EDCB-1#TRPBF LDHC 6-Lead (2mm x 3mm) Plastic DFN -40C to 85C LEAD BASED FINISH TAPE AND REEL S6 PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1934ES6 LT1934ES6#TR LTXP 6-Lead Plastic TSOT-23 -40C to 85C LT1934ES6-1 LT1934ES6-1#TR LTF8 6-Lead Plastic TSOT-23 -40C to 85C LT1934IS6 LT1934IS6#TR LTAJB 6-Lead Plastic TSOT-23 -40C to 125C LT1934IS6-1 LT1934IS6-1#TR LTAJC 6-Lead Plastic TSOT-23 -40C to 125C LT1934IDCB LT1934IDCB#TR LCFZ 6-Lead (2mm x 3mm) Plastic DFN -40C to 125C LT1934EDCB LT1934EDCB#TR LCFZ 6-Lead (2mm x 3mm) Plastic DFN -40C to 85C LT1934IDCB-1 LT1934IDCB-1#TR LDHC 6-Lead (2mm x 3mm) Plastic DFN -40C to 125C LT1934EDCB-1 LT1934EDCB-1#TR LDHC 6-Lead (2mm x 3mm) Plastic DFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ 1934fe 2 LT1934/LT1934-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 10V, VBOOST = 15V, unless otherwise noted. SYMBOL CONDITIONS MIN Undervoltage Lockout Quiescent Current UNITS l l 3 3 3 3.2 3.6 3.6 V V V -40C TA 85C -40C TA 125C l l 12 12 12 22 26 26 A A A 0.01 2 A -40C TA 85C -40C TA 125C l l 1.25 1.25 1.27 1.27 V V VFB = 1.3V VFB Falling MAX -40C TA 85C -40C TA 125C VSHDN = 0V FB Comparator Trip Voltage TYP 1.22 1.21 FB Comparator Hysteresis 10 FB Pin Bias Current VFB = 1.25V -40C TA 85C -40C TA 125C FB Voltage Line Regulation 4V < VIN < 34V Switch Off Time VFB > 1V VFB = 0V Maximum Duty Cycle VFB = 1V Switch VCESAT ISW = 300mA (LT1934, S6 Package) ISW = 300mA (LT1934, DCB Package) ISW = 75mA (LT1934-1, S6 Package) ISW = 75mA (LT1934-1, DCB Package) l l 2 2 mV 15 60 0.007 -40C TA 85C -40C TA 125C l l 1.4 1.8 12 85 83 88 88 350 90 nA nA %/V 2.3 s s % % 200 225 65 70 300 400 120 490 160 mA mA 120 mV mV mV mV Switch Current Limit LT1934 LT1934-1 BOOST Pin Current ISW = 300mA (LT1934) ISW = 75mA (LT1934-1) 8.5 6.0 12 10 mA mA Minimum Boost Voltage (Note 3) ISW = 300mA (LT1934) ISW = 75mA (LT1934-1) 1.8 1.7 2.5 2.5 V V VSHDN = 2.3V VSHDN = 34V 0.5 1.5 Switch Leakage Current SHDN Pin Current SHDN Input Voltage High SHDN Input Voltage Low Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT1934E and LT1934E-1 are guaranteed to meet performance specifications from 0C to 85C. Specifications over the -40C to 85C 2 A 5 A A 2.3 V 0.25 V operating temperature range are assured by design, characterization and correlation with statistical process controls. The LT1934I and LT1934I-1 specifications are guaranteed over the -40C to 125C temperature range. Note 3: This is the minimum voltage across the boost capacitor needed to guarantee full saturation of the internal power switch. 1934fe 3 LT1934/LT1934-1 TYPICAL PERFORMANCE CHARACTERISTICS LT1934 Efficiency, VOUT = 5V LT1934 Efficiency, VOUT = 3.3V LT1934 VOUT = 3.3V L = 47H 90 TA = 25C VIN = 12V 80 EFFICIENCY (%) EFFICIENCY (%) LT1934 VOUT = 5V L = 47H 90 TA = 25C VIN = 24V 70 60 90 80 VIN = 24V VIN = 12V 70 50 100 1934 G03 Off Time vs Temperature 3.0 VIN = 12V VIN = 24V 70 60 10 300 200 100 2.0 1.5 1.0 LT1934-1 100 0.5 0 -50 50 1 2.5 400 OFF TIME (s) SWITCH CURRENT LIMIT (mA) LT1934 80 -25 LOAD CURRENT (mA) 50 25 0 75 TEMPERATURE (C) 1934 G04 100 0 -50 -25 125 50 25 75 0 TEMPERATURE (C) 100 SHDN Bias Current vs SHDN Voltage VFB vs Temperature 1.27 TA = 25oC 125 1934 G06 1934 G05 Frequency Foldback 16 10 LOAD CURRENT (mA) Current Limit vs Temperature LT1934-1 VOUT = 3.3V L = 100H TA = 25C 1 0.1 500 0.1 70 1934 G02 LT1934-1 Efficiency, VOUT = 3.3V 90 VIN = 24V 1 10 100 LOAD CURRENT (mA) 1934 G01 100 VIN = 12V 80 60 50 0.1 1 10 100 LOAD CURRENT (mA) LT1934-1 VOUT = 5V L = 150H TA = 25C VIN = 5V 60 50 0.1 EFFICIENCY (%) LT1934-1 Efficiency, VOUT = 5V 100 100 EFFICIENCY (%) 100 2.0 TA = 25C 14 10 8 6 4 SHDN PIN CURRENT (A) FEEDBACK VOLTAGE (V) SWITCH OFF TIME (s) 1.26 12 1.25 1.24 1.5 1.0 0.5 1.23 2 0 0 0.2 0.4 0.8 1.0 0.6 FEEDBACK PIN VOLTAGE (V) 1.2 1934 G07 1.22 -50 0 -25 50 25 0 75 TEMPERATURE (C) 100 125 1934 G08 0 2 4 6 8 SHDN PIN VOLTAGE (V) 10 12 1934 G09 1934fe 4 LT1934/LT1934-1 TYPICAL PERFORMANCE CHARACTERISTICS Undervoltage Lockout vs Temperature 20 4.0 15 3.5 UVLO (V) QUIESCENT CURRENT (A) Quiescent Current vs Temperature 10 5 3.0 2.5 0 -50 -25 75 0 25 50 TEMPERATURE (C) 100 2.0 -50 125 -25 75 0 25 50 TEMPERATURE (C) 100 1934 G10 1934 G11 Minimum Input Voltage VOUT = 5V Minimum Input Voltage VOUT = 3.3V 6.0 8 LT1934 VOUT = 5V TA = 25C 7 BOOST DIODE TIED TO OUTPUT INPUT VOLTAGE (V) INPUT VOLTAGE (V) LT1934 VOUT = 3.3V 5.5 TA = 25C BOOST DIODE TIED TO OUTPUT 5.0 125 VIN TO START 4.5 4.0 VIN TO RUN VIN TO START 6 VIN TO RUN 5 3.5 3.0 0.1 4 0.1 1 10 100 LOAD CURRENT (mA) 1934 G12 PIN FUNCTIONS 1 10 100 LOAD CURRENT (mA) 1934 G13 (TSOT-23/DFN) BOOST (Pin 1/Pin 1): The BOOST pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. in shutdown mode. Tie to ground to shut down the LT1934. Apply 2.3V or more for normal operation. If the shutdown feature is not used, tie this pin to the VIN pin. GND (Pin 2/Pin 5): Tie the GND pin to a local ground plane below the LT1934 and the circuit components. Return the feedback divider to this pin. VIN (Pin 5/Pin 3): The VIN pin supplies current to the LT1934's internal regulator and to the internal power switch. This pin must be locally bypassed. FB (Pin 3/Pin 6): The LT1934 regulates its feedback pin to 1.25V. Connect the feedback resistor divider tap to this pin. Set the output voltage according to VOUT = 1.25V (1 + R1/R2) or R1 = R2 (VOUT/1.25 - 1). SW (Pin 6/Pin 2): The SW pin is the output of the internal power switch. Connect this pin to the inductor, catch diode and boost capacitor. SHDN (Pin 4/Pin 4): The SHDN pin is used to put the LT1934 Exposed Pad (Pin 7, DFN Package): This pin must be soldered to ground plane. 1934fe 5 LT1934/LT1934-1 BLOCK DIAGRAM VIN VIN + C2 + - D2 BOOST ON TIME R Qa 12s DELAY S OFF TIME SHDN L1 SW 1.8s DELAY ON OFF C3 Q VOUT D1 C1 + VREF 1.25V ENABLE - GND FEEDBACK COMPARATOR FB R2 R1 1934 BD 1934fe 6 LT1934/LT1934-1 OPERATION (Refer to Block Diagram) The LT1934 uses Burst Mode control, combining both low quiescent current operation and high switching frequency, which result in high efficiency across a wide range of load currents and a small total circuit size. A comparator monitors the voltage at the FB pin of the LT1934. If this voltage is higher than the internal 1.25V reference, the comparator disables the oscillator and power switch. In this state, only the comparator, reference and undervoltage lockout circuits are active, and the current into the VIN pin is just 12A. As the load current discharges the output capacitor, the voltage at the FB pin falls below 1.25V and the comparator enables the oscillator. The LT1934 begins to switch, delivering current to the output capacitor. The output voltage rises, and when it overcomes the feedback comparator's hysteresis, the oscillator is disabled and the LT1934 returns to its micropower state. The oscillator consists of two one-shots and a flip-flop. A rising edge from the off-time one-shot sets the flip-flop, which turns on the internal NPN power switch. The switch remains on until either the on-time one-shot trips or the current limit is reached. A sense resistor and amplifier monitor the current through the switch and resets the flip-flop when this current reaches 400mA (120mA for the LT1934-1). After the 1.8s delay of the off-time oneshot, the cycle repeats. Generally, the LT1934 will reach current limit on every cycle--the off time is fixed and the on time is regulated so that the LT1934 operates at the correct duty cycle. The 1.8s off time is lengthened when the FB pin voltage falls below 0.8V; this foldback behavior helps control the output current during start-up and overload. Figure 1 shows several waveforms of an LT1934 producing 3.3V from a 10V input. When the switch is on, the SW pin voltage is at 10V. When the switch is off, the inductor current pulls the SW pin down until it is clamped near ground by the external catch diode. The switch driver operates from either the input or from the BOOST pin. An external capacitor and diode are used to generate a voltage at the BOOST pin that is higher than the input supply. This allows the driver to fully saturate the bipolar switch for efficient operation. If the SHDN pin is grounded, all internal circuits are turned off and VIN current reduces to the device leakage current, typically a few nA. VOUT 50mV/DIV VSW 10V/DIV ISW 0.5A/DIV ILI 0.5A/DIV 1934 F01a 5s/DIV Figure 1. Operating Waveforms of the LT1934 Converting 10V to 3.3V at 180mA (Front Page Schematic) 1934fe 7 LT1934/LT1934-1 APPLICATIONS INFORMATION Which One to Use: LT1934 or LT1934-1? The only difference between the LT1934 and LT1934-1 is the peak current through the internal switch and the inductor. If your maximum load current is less than 60mA, use the LT1934-1. If your maximum load is higher, use the LT1934; it can supply up to ~300mA. While the LT1934-1 can't deliver as much output current, it has other advantages. The lower peak switch current allows the use of smaller components (input capacitor, inductor and output capacitor). The ripple current at the input of the LT1934-1 circuit will be smaller and may be an important consideration if the input supply is current limited or has high impedance. The LT1934-1's current draw during faults (output overload or short) and startup is lower. The maximum load current that the LT1934 or LT1934-1 can deliver depends on the value of the inductor used. Table 1 lists inductor value, minimum output capacitor and maximum load for 3.3V and 5V circuits. Increasing the value of the capacitor will lower the output voltage ripple. Component selection is covered in more detail in the following sections. Minimum Input Voltage The minimum input voltage required to generate a particular output voltage is determined by either the LT1934's undervoltage lockout of ~3V or by its maximum duty cycle. The duty cycle is the fraction of time that the internal switch is on and is determined by the input and output voltages: DC = (VOUT + VD)/(VIN - VSW + VD) where VD is the forward voltage drop of the catch diode (~0.4V) and VSW is the voltage drop of the internal switch (~0.3V at maximum load for the LT1934, ~0.1V for the LT1934-1). This leads to a minimum input voltage of: VIN(MIN) = (VOUT + VD)/DCMAX - VD + VSW with DCMAX = 0.85. Inductor Selection A good first choice for the inductor value is: L = 2.5 * (VOUT + VD) * 1.8s/ILIM where ILIM is the switch current limit (400mA for the LT1934 and 120mA for the LT1934-1). This choice provides a worst-case maximum load current of 250mA (60mA for the LT1934-1). The inductor's RMS current rating must be greater than the load current and its saturation current should be greater than ILIM . To keep efficiency high, the series resistance (DCR) should be less than 0.3 (1 for the LT1934-1). Table 2 lists several vendors and types that are suitable. PART VOUT L MINIMUM COUT MAXIMUM LOAD LT1934 3.3V 100H 47H 33H 100H 47H 33H 300mA 250mA 200mA 5V 150H 68H 47H 47H 33H 22H 300mA 250mA 200mA This simple rule may not provide the optimum value for your application. If the load current is less, then you can relax the value of the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. The following provides more details to guide inductor selection. First, the value must be chosen so that the LT1934 can supply the maximum load current drawn from the output. Second, the inductor must be rated appropriately so that the LT1934 will function reliably and the inductor itself will not be overly stressed. 3.3V 150H 100H 68H 15H 10H 10H 60mA 45mA 20mA Detailed Inductor Selection and Maximum Load Current 5V 220H 150H 100H 10H 4.7H 4.7H 60mA 45mA 20mA Table 1 LT1934-1 The square wave that the LT1934 produces at its switch pin results in a triangle wave of current in the inductor. The LT1934 limits the peak inductor current to ILIM . Because 1934fe 8 LT1934/LT1934-1 APPLICATIONS INFORMATION Table 2. Inductor Vendors VENDOR PHONE URL PART SERIES COMMENTS Murata (404) 426-1300 www.murata.com LQH3C Small, Low Cost, 2mm Height Sumida (847) 956-0666 www.sumida.com CR43 CDRH4D28 CDRH5D28 Coilcraft (847) 639-6400 www.coilcraft.com DO1607C DO1608C DT1608C Wurth Electronics (866) 362-6673 www.we-online.com WE-PD1, 2, 3, 4 the average inductor current equals the load current, the maximum load current is: IOUT(MAX) = IPK - IL /2 where IPK is the peak inductor current and IL is the peak-to-peak ripple current in the inductor. The ripple current is determined by the off time, tOFF = 1.8s, and the inductor value: IL = (VOUT + VD) * tOFF /L IPK is nominally equal to ILIM . However, there is a slight delay in the control circuitry that results in a higher peak current and a more accurate value is: IPK = ILIM + 150ns * (VIN - VOUT)/L These expressions are combined to give the maximum load current that the LT1934 will deliver: IOUT(MAX) = 350mA + 150ns * (VIN - VOUT)/L - 1.8s * (VOUT + VD)/2L (LT1934) IOUT(MAX) = 90mA + 150ns * (VIN - VOUT)/L - 1.8s * (VOUT + VD)/2L (LT1934-1) The minimum current limit is used here to be conservative. The third term is generally larger than the second term, so that increasing the inductor value results in a higher output current. This equation can be used to evaluate a chosen inductor or it can be used to choose L for a given maximum load current. The simple, single equation rule given above for choosing L was found by setting IL = ILIM /2.5. This results in IOUT(MAX) ~0.8ILIM (ignoring the delay term). Note that this analysis assumes that the inductor current is continuous, which is true if the ripple current is less than the peak current or IL < IPK. The inductor must carry the peak current without saturating excessively. When an inductor carries too much current, its core material can no longer generate additional magnetic flux (it saturates) and the inductance drops, sometimes very rapidly with increasing current. This condition allows the inductor current to increase at a very high rate, leading to high ripple current and decreased overload protection. Inductor vendors provide current ratings for power inductors. These are based on either the saturation current or on the RMS current that the inductor can carry without dissipating too much power. In some cases it is not clear which of these two determine the current rating. Some data sheets are more thorough and show two current ratings, one for saturation and one for dissipation. For LT1934 applications, the RMS current rating should be higher than the load current, while the saturation current should be higher than the peak inductor current calculated above. Input Capacitor Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT1934 and to force this switching current into a tight local loop, minimizing EMI. The input capacitor must have low impedance at the switching frequency to do this effectively. A 2.2F ceramic capacitor (1F for the LT1934-1) satisfies these requirements. If the input source impedance is high, a larger value capacitor may be required to keep input ripple low. In this case, an electrolytic of 10F or more in parallel with a 1F ceramic is a good combination. Be aware that the input 1934fe 9 LT1934/LT1934-1 APPLICATIONS INFORMATION capacitor is subject to large surge currents if the LT1934 circuit is connected to a low impedance supply, and that some electrolytic capacitors (in particular tantalum) must be specified for such use. Output Capacitor and Output Ripple The output capacitor filters the inductor's ripple current and stores energy to satisfy the load current when the LT1934 is quiescent. In order to keep output voltage ripple low, the impedance of the capacitor must be low at the LT1934's switching frequency. The capacitor's equivalent series resistance (ESR) determines this impedance. Choose one with low ESR intended for use in switching regulators. The contribution to ripple voltage due to the ESR is approximately ILIM * ESR. ESR should be less than ~150m for the LT1934 and less than ~500m for the LT1934-1. The value of the output capacitor must be large enough to accept the energy stored in the inductor without a large change in output voltage. Setting this voltage step equal to 1% of the output voltage, the output capacitor must be: COUT > 50 * L * (ILIM /VOUT)2 For example, an LT1934 producing 3.3V with L = 47H requires 33F. This value can be relaxed if small circuit size is more important than low output ripple. Sanyo's POSCAP series in B-case and C-case sizes provides very good performance in a small package for the LT1934. Similar performance in traditional tantalum capacitors requires a larger package (C- or D-case). The LT1934-1, with its lower switch current, can use a B-case tantalum capacitor. With a high quality capacitor filtering the ripple current from the inductor, the output voltage ripple is determined by the hysteresis and delay in the LT1934's feedback comparator. This ripple can be reduced further by adding a small (typically 10pF) phase lead capacitor between the output and the feedback pin. Ceramic Capacitors Ceramic capacitors are small, robust and have very low ESR. However, ceramic capacitors can cause problems when used with the LT1934. Not all ceramic capacitors are suitable. X5R and X7R types are stable over temperature and applied voltage and give dependable service. Other types (Y5V and Z5U) have very large temperature and voltage coefficients of capacitance. In the application circuit they may have only a small fraction of their nominal capacitance and voltage ripple may be much larger than expected. Ceramic capacitors are piezoelectric. The LT1934's switching frequency depends on the load current, and at light loads the LT1934 can excite the ceramic capacitor at audio frequencies, generating audible noise. If this is unacceptable, use a high performance electrolytic capacitor at the output. The input capacitor can be a parallel combination of a 2.2F ceramic capacitor and a low cost electrolytic capacitor. The level of noise produced by the LT1934-1 Table 3. Capacitor Vendors VENDOR PHONE URL PART SERIES COMMENTS Panasonic (714) 373-7366 www.panasonic.com Ceramic, Polymer, Tantalum EEF Series Kemet Sanyo Murata (864) 963-6300 (408) 749-9714 (404) 436-1300 AVX Taiyo Yuden (864) 963-6300 www.kemet.com www.sanyovideo.com Ceramic, Tantalum Ceramic, Polymer, Tantalum www.murata.com Ceramic, www.avxcorp.com Ceramic, Tantalum T494, T495 POSCAP TPS Series www.taiyo-yuden.com Ceramic 1934fe 10 LT1934/LT1934-1 APPLICATIONS INFORMATION when used with ceramic capacitors will be lower and may be acceptable. A final precaution regarding ceramic capacitors concerns the maximum input voltage rating of the LT1934. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT1934 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT1934's rating. This situation is easily avoided; see the Hot Plugging Safely section. D2 BOOST C3 LT1934 VIN VIN VOUT SW GND VBOOST - VSW VOUT MAX VBOOST VIN + VOUT (2a) D2 Catch Diode C3 BOOST LT1934 A 0.5A Schottky diode is recommended for the catch diode, D1. The diode must have a reverse voltage rating equal to or greater than the maximum input voltage. The ON Semiconductor MBR0540 is a good choice; it is rated for 0.5A forward current and a maximum reverse voltage of 40V. Schottky diodes with lower reverse voltage ratings usually have a lower forward drop and may result in higher efficiency with moderate to high load currents. However, these diodes also have higher leakage currents. This leakage current mimics a load current at the output and can raise the quiescent current of the LT1934 circuit, especially at elevated temperatures. BOOST Pin Considerations Capacitor C3 and diode D2 are used to generate a boost voltage that is higher than the input voltage. In most cases a 0.1F capacitor and fast switching diode (such as the 1N4148 or 1N914) will work well. Figure 2 shows two ways to arrange the boost circuit. The BOOST pin must be more than 2.5V above the SW pin for best efficiency. For outputs of 3.3V and above, the standard circuit (Figure 2a) is best. For outputs between 2.8V and 3V, use a 0.22F capacitor and a small Schottky diode (such as the BAT-54). For lower output voltages the boost diode can be tied to the input (Figure 2b). The circuit in Figure 2a is more efficient because the BOOST pin current comes from a lower voltage source. You must also be sure that the maximum voltage rating of the BOOST pin is not exceeded. The minimum operating voltage of an LT1934 application is limited by the undervoltage lockout (~3V) and by VIN VIN SW VOUT GND 1934 F02 VBOOST - VSW VIN MAX VBOOST 2VIN (2b) Figure 2. Two Circuits for Generating the Boost Voltage the maximum duty cycle as outlined above. For proper start-up, the minimum input voltage is also limited by the boost circuit. If the input voltage is ramped slowly, or the LT1934 is turned on with its SHDN pin when the output is already in regulation, then the boost capacitor may not be fully charged. Because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The minimum load generally goes to zero once the circuit has started. Figure 3 shows a plot of minimum load to start and to run as a function of input voltage. In many cases the discharged output capacitor will present a load to the switcher which will allow it to start. The plots show the worst-case situation where VIN is ramping very slowly. Use a Schottky diode (such as the BAT-54) for the lowest start-up voltage. At light loads, the inductor current becomes discontinuous and the effective duty cycle can be very high. This reduces the minimum input voltage to approximately 300mV above VOUT. At higher load currents, the inductor current is continuous and the duty cycle is limited by the 1934fe 11 LT1934/LT1934-1 APPLICATIONS INFORMATION Minimum Input Voltage VOUT = 3.3V 6.0 INPUT VOLTAGE (V) LT1934 VOUT = 3.3V 5.5 TA = 25C BOOST DIODE TIED TO OUTPUT 5.0 VIN TO START 4.5 4.0 VIN TO RUN 3.5 3.0 0.1 to VIN), then the LT1934's internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few mA in this state. If you ground the SHDN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT1934 can pull large currents from the output through the SW pin and the VIN pin. Figure 4 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. D4 10 100 1 LOAD CURRENT (mA) 5 VIN VIN 100k 4 Minimum Input Voltage VOUT = 5V INPUT VOLTAGE (V) GND 2 SW 6 VOUT FB 3 BACKUP VIN TO START D4: MBR0530 6 1934 F07 Figure 4. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output; It Also Protects the Circuit from a Reversed Input. The LT1934 Runs Only When the Input is Present VIN TO RUN 5 4 0.1 SHDN 1M LT1934 VOUT = 5V TA = 25C 7 BOOST DIODE TIED TO OUTPUT 1 LT1934 1934 G12 8 BOOST PCB Layout 1 10 100 LOAD CURRENT (mA) 1934 G13 Figure 3. The Minimum Input Voltage Depends on Output Voltage, Load Current and Boost Circuit maximum duty cycle of the LT1934, requiring a higher input voltage to maintain regulation. Shorted Input Protection If the inductor is chosen so that it won't saturate excessively, an LT1934 buck regulator will tolerate a shorted output. There is another situation to consider in systems where the output will be held high when the input to the LT1934 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode OR-ed with the LT1934's output. If the VIN pin is allowed to float and the SHDN pin is held high (either by a logic signal or because it is tied For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 5 shows the high current paths in the buck regulator circuit. Note that large, switched currents flow in the power switch, the catch diode (D1) and the input capacitor (C2). The loop formed by these components should be as small as possible. Furthermore, the system ground should be tied to the regulator ground in only one place; this prevents the switched current from injecting noise into the system ground. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane below these components, and tie this ground plane to system ground at one location, ideally at the ground terminal of the output capacitor C1. Additionally, the SW and BOOST nodes should be kept as small as possible. Finally, keep the FB node as small as possible so that the ground pin 1934fe 12 LT1934/LT1934-1 APPLICATIONS INFORMATION VIN VIN SW GND SW GND (5a) (5b) IC1 VSW VIN C2 L1 SW D1 GND C1 1934 F05 (5c) Figure 5. Subtracting the Current When the Switch is On (a) from the Current When the Switch is Off (b) Reveals the Path of the High Frequency Switching Current (c). Keep This Loop Small. The Voltage on the SW and BOOST Nodes Will Also be Switched; Keep These Nodes as Small as Possible. Finally, Make Sure the Circuit is Shielded with a Local Ground Plane SHUTDOWN VIN VOUT SYSTEM GROUND VIAS TO LOCAL GROUND PLANE OUTLINE OF LOCAL GROUND PLANE 1934 F06 Figure 6. A Good PCB Layout Ensures Proper, Low EMI Operation and ground traces will shield it from the SW and BOOST nodes. Figure 6 shows component placement with trace, ground plane and via locations. Include two vias near the GND pin of the LT1934 to help remove heat from the LT1934 to the ground plane. Hot Plugging Safely The small size, robustness and low impedance of ceramic capacitors make them an attractive option for the input bypass capacitor of LT1934 and LT1934-1 circuits. However, these capacitors can cause problems if the LT1934 is plugged into a live supply (see Linear Technology Application Note 88 for a complete discussion). The low loss ceramic capacitor combined with stray inductance in series with the power source forms an under damped tank circuit, and the voltage at the VIN pin of the LT1934 can ring to twice the nominal input voltage, possibly exceeding the LT1934's rating and damaging the part. If the input supply is poorly controlled or the user will be plugging the LT1934 into an energized supply, the input network should be designed to prevent this overshoot. 1934fe 13 LT1934/LT1934-1 APPLICATIONS INFORMATION Figure 7 shows the waveforms that result when an LT1934 circuit is connected to a 24V supply through six feet of 24-gauge twisted pair. The first plot is the response with a 2.2F ceramic capacitor at the input. The input voltage rings as high as 35V and the input current peaks at 20A. One method of damping the tank circuit is to add another capacitor with a series resistor to the circuit. In Figure 7b an aluminum electrolytic capacitor has been added. This capacitor's high equivalent series resistance damps the circuit and eliminates the voltage overshoot. The extra capacitor improves low frequency ripple filtering and can slightly improve the efficiency of the circuit, though it is likely to be the largest component in the circuit. An alternative solution is shown in Figure 7c. A 1 resistor is added CLOSING SWITCH SIMULATES HOT PLUG IIN VIN LT1934 + VIN 10V/DIV 2.2F LOW IMPEDANCE ENERGIZED 24V SUPPLY IIN 10A/DIV STRAY INDUCTANCE DUE TO 6 FEET (2 METERS) OF TWISTED PAIR 10s/DIV (7a) LT1934 10F 35V AI.EI. + 2.2F (7b) 1 LT1934 0.1F 2.2F (7c) LT1934-1 1F (7d) 4.7 LT1934-1 0.1F 1F (7e) 1934 F07 Figure 7. A Well Chosen Input Network Prevents Input Voltage Overshoot and Ensures Reliable Operation When the LT1934 is Connected to a Live Supply 1934fe 14 LT1934/LT1934-1 APPLICATIONS INFORMATION in series with the input to eliminate the voltage overshoot (it also reduces the peak input current). A 0.1F capacitor improves high frequency filtering. This solution is smaller and less expensive than the electrolytic capacitor. For high input voltages its impact on efficiency is minor, reducing efficiency less than one half percent for a 5V output at full load operating from 24V. Voltage overshoot gets worse with reduced input capacitance. Figure 7d shows the hot plug response with a 1F ceramic input capacitor, with the input ringing above 40V. The LT1934-1 can tolerate a larger input resistance, such as shown in Figure 7e where a 4.7 resistor damps the voltage transient and greatly reduces the input current glitch on the 24V supply. High Temperature Considerations The die temperature of the LT1934 must be lower than the maximum rating of 125C. This is generally not a concern unless the ambient temperature is above 85C. For higher temperatures, care should be taken in the layout of the circuit to ensure good heat sinking of the LT1934. The maximum load current should be derated as the ambient temperature approaches 125C. The die temperature is calculated by multiplying the LT1934 power dissipation by the thermal resistance from junction to ambient. Power dissipation within the LT1934 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the catch diode loss. The resulting temperature rise at full load is nearly independent of input voltage. Thermal resistance depends on the layout of the circuit board, but a value of 150C/W is typical for the TSOT-23 and 75C/W for the DFN. The temperature rise for an LT1934 (TSOT-23) producing 5V at 250mA is approximately 25C, allowing it to deliver full load to 100C ambient. Above this temperature the load current should be reduced. For 3.3V at 250mA the temperature rise is 15C. The DFN temperature rise will be roughly one-half of these values. Finally, be aware that at high ambient temperatures the external Schottky diode, D1, is likely to have significant leakage current, increasing the quiescent current of the LT1934 converter. Outputs Greater Than 6V For outputs greater than 6V, tie a diode (such as a 1N4148) from the SW pin to VIN to prevent the SW pin from ringing above VIN during discontinuous mode operation. The 12V output circuit in Typical Applications shows the location of this diode. Also note that for outputs above 6V, the input voltage range will be limited by the maximum rating of the BOOST pin. The 12V circuit shows how to overcome this limitation using an additional Zener diode. 1934fe 15 LT1934/LT1934-1 TYPICAL APPLICATIONS 3.3V Step-Down Converter D2 0.1F BOOST VIN 4.5V TO 34V D1 LT1934-1 SHDN ON OFF VOUT 3.3V 45mA SW VIN C2 1F L1 100H 10pF 1M + FB C1 22F 604k GND C1: TAIYO YUDEN JMK316BJ226ML C2: TAIYO YUDEN GMK316BJ105ML D1: ZETEX ZHCS400 OR ON SEMI MBR0540 D2: CENTRAL CMDSH-3 L1: COILCRAFT DO1608C-104 OR WURTH ELECTRONICS WE-PD4 TYPE S 1934 TA04 5V Step-Down Converter D2 0.1F BOOST VIN 6.5V TO 34V ON OFF VOUT 5V 45mA SW VIN C2 1F L1 150H D1 LT1934-1 SHDN 10pF 1M + FB GND C1: TAIYO YUDEN JMK316BJ226ML C2: TAIYO YUDEN GMK316BJ105ML D1: ZETEX ZHCS400 OR ON SEMI MBR0540 D2: CENTRAL CMPD914 L1: COILCRAFT DO1608C-154 OR WURTH ELECTRONICS WE-PD4 TYPE S C1 22F 332k 1934 TA05 1934fe 16 LT1934/LT1934-1 TYPICAL APPLICATIONS 1.8V Step-Down Converter D2 0.1F BOOST VIN 3.6V TO 16V VIN C2 2.2F VOUT 1.8V 250mA SW D1 LT1934 147k SHDN ON OFF L1 33H + FB C1 100F 332k GND C1: SANYO 2R5TPB100M C2: TAIYO YUDEN EMK316BJ225ML D1: ZETEX ZHCS400 OR ON SEMI MBR0540 D2: CENTRAL CMPD914 L1: SUMIDA CR43-330 1934 TA06 Loop Powered 3.3V Supply with Additional Isolated Output D3 L1B 50H * SW VIN D4 10V 390k GND * D1 LT1934-1 SHDN 1F D2 C1 L1A 50H BOOST VIN 14V TO 32V <3.6mA + ISOLATED OUT 3V 10F 3mA 1M 10pF VOUT 3V 9mA + FB 33F 715k D1: ON SEMICONDUCTOR MBR0540 D2, D3: BAT54 D4: CENTRAL CMPZ5240B L1: COILTRONICS CTX50-1 ZENER DIODE D4 PROVIDES AN UNDERVOLTAGE LOCKOUT, REDUCING THE INPUT CURRENT REQUIRED AT START-UP 1934 TA08 1934fe 17 LT1934/LT1934-1 TYPICAL APPLICATIONS Standalone 350mA Li-Ion Battery Charger D2 0.1F L1 47H BOOST D3 VIN 7V TO 28V VIN SHDN CHRG GATE 0.022F LTC4052 FB 332k 0.047F VIN D1 1M GND + 10k SW LT1934 C2 1F 1k 1k + ACPR SENSE TIMER GND BAT C1 47F CTIMER 0.1F C5 10F C1: SANYO 6TPB47M C2: TAIYO YUDEN GMK316BJ105ML D1, D3: ON SEMICONDUCTOR MBR0540 D2: CENTRAL CMDSH-3 L1: SUMIDA CR43-470 (619) 661-6835 (408) 573-4150 (602) 244-6600 (516) 435-1110 (847) 956-0667 350mA 1-CELL 4.2V Li-Ion BATTERY 1934 TA07a CHARGE STATUS AC PRESENT 500 VIN = 24V CHARGE CURRENT (mA) 400 300 VIN = 8V VIN = 12V 200 100 0 2.5 3.5 3 4 BATTERY VOLTAGE (V) 4.5 1934 TA07b 12V Step-Down Converter D2 D4 0.1F D3 L1 100H BOOST VIN 15V TO 32V ON OFF VIN C2 2.2F VOUT 12V 170mA SW LT1934 SHDN D1 866k FB GND C1: KEMET T495D226K020AS C2: TAIYO YUDEN GMK325BJ225MN D1: ON SEMI MBR0540 D2, D4: CENTRAL CMPD914 D3: CENTRAL CMPZ5234B 6.2V ZENER L1: TDK SLF6028T-101MR42 + C1 22F 100k 1934 TA09 1934fe 18 LT1934/LT1934-1 PACKAGE DESCRIPTION S6 Package 6-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1636) 0.62 MAX 2.90 BSC (NOTE 4) 0.95 REF 1.22 REF 2.80 BSC 1.4 MIN 3.85 MAX 2.62 REF 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.30 - 0.45 6 PLCS (NOTE 3) 0.95 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 1.90 BSC 0.09 - 0.20 (NOTE 3) NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 S6 TSOT-23 0302 REV B DCB Package 6-Lead Plastic DFN (2mm x 3mm) (Reference LTC DWG # 05-08-1715) R = 0.115 TYP R = 0.05 TYP 2.00 0.10 (2 SIDES) 0.70 0.05 3.55 0.05 1.65 0.05 (2 SIDES) 3.00 0.10 (2 SIDES) 0.40 0.10 4 6 1.65 0.10 (2 SIDES) 2.15 0.05 PACKAGE OUTLINE PIN 1 NOTCH R0.20 OR 0.25 s 45 CHAMFER PIN 1 BAR TOP MARK (SEE NOTE 6) 3 0.25 0.05 0.50 BSC 0.200 REF (DCB6) DFN 0405 0.25 0.05 0.50 BSC 0.75 0.05 1.35 0.10 (2 SIDES) 1.35 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 1 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (TBD) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 1934fe 19 LT1934/LT1934-1 TYPICAL APPLICATION 5V Step-Down Converter D2 0.1F BOOST VIN 6.5V TO 34V D1 LT1934 SHDN ON OFF VOUT 5V 250mA SW VIN C2 2.2F L1 68H 10pF 1M + FB C1 68F 332k GND C1: SANYO 6TPB68M C2: TAIYO YUDEN GMK325BJ225MN D1: ZETEX ZHCS400 OR ON SEMI MBR0540 D2: CENTRAL CMPD914 L1: SUMIDA CDRH5D28-680 1934 TA03 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1616 25V, 500mA (IOUT), 1.4MHz, High Efficiency Step-Down DC/DC Converter VIN = 3.6V to 25V, VOUT = 1.25V, IQ = 1.9mA , ISD < 1A, ThinSOT Package LT1676 60V, 440mA (IOUT), 100kHz, High Efficiency Step-Down DC/DC Converter VIN = 7.4V to 60V, VOUT = 1.24V, IQ = 3.2mA , ISD = 2.5A, S8 Package LT1765 25V, 2.75A (IOUT), 1.25MHz, High Efficiency Step-Down DC/DC Converter VIN = 3V to 25V, VOUT = 1.2V, IQ = 1mA , ISD = 15A, S8, TSSOP16E Packages LT1766 60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA , ISD = 25A, TSSOP16/E Package LT1767 25V, 1.2A (IOUT), 1.25MHz, High Efficiency Step-Down DC/DC Converter VIN = 3V to 25V; VOUT = 1.2V, IQ = 1mA, ISD = 6A, MS8/E Packages LT1776 40V, 550mA (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN = 7.4V to 40V; VOUT = 1.24V, IQ = 3.2mA, ISD = 30A, N8, S8 Packages LTC(R)1877 600mA (IOUT), 550kHz, Synchronous Step-Down DC/DC Converter VIN = 2.7V to 10V; VOUT = 0.8V, IQ = 10A, ISD < 1A, MS8 Package LTC1879 1.2A (IOUT), 550kHz, Synchronous Step-Down DC/DC Converter VIN = 2.7V to 10V; VOUT = 0.8V, IQ = 15A, ISD < 1A, TSSOP16 Package LT1956 60V, 1.2A (IOUT), 500kHz, High Efficiency Step-Down DC/DC Converter VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA, ISD = 25A, TSSOP16/E Package LTC3405/LTC3405A 300mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter VIN = 2.7V to 6V, VOUT = 0.8V, IQ = 20A, ISD < 1A, ThinSOT Package LTC3406/LTC3406B 600mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter VIN = 2.5V to 5.5V, VOUT = 0.6V, IQ = 20A, ISD < 1A, ThinSOT Package LTC3411 1.25A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter VIN = 2.5V to 5.5V, VOUT = 0.8V, IQ = 60A, ISD < 1A, MS Package LTC3412 2.5A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter VIN = 2.5V to 5.5V, VOUT = 0.8V, IQ = 60A, ISD < 1A, TSSOP16E Package LTC3430 60V, 2.75A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN = 5.5V to 60V, VOUT = 1.2V, IQ = 2.5mA, ISD = 30A, TSSOP16E Package 1934fe 20 Linear Technology Corporation LT 0209 REV E * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2002