DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Features The AAT3103 is a constant frequency charge-pump based current-source white LED driver capable of driving one to three LEDs up to 30mA, each. The charge pumps automatically switch between 1x mode and 2x mode to maintain the highest efficiency and optimal LED current accuracy and matching. A low external parts count (one 1F flying capacitor, two small 1F capacitors at IN and OUT and one current setting resistor) makes the AAT3103 ideally suited for small battery-powered applications. * * * * * * * * * * The AAT3103-1/-2 uses Skyworks' Simple Serial ControlTM (S2CwireTM) interface to enable, disable, and program the LED driving current. The AAT3103-4 employs a Pulse Width Modulation (PWM) signal with up to 50kHz frequency, 10% to 100% duty cycle to program the LED current. A low-current shutdown feature disconnects the load from IN and reduces quiescent current to less than 1A. Built-in soft-start circuitry prevents excessive inrush current during start-up. Integrated short circuit and thermal protection circuitry protects the device from damage. Source WLED Driver, up to 3 LEDs at up to 30mA, each Automatic Switching Between 1x and 2x Modes 900KHz Switching Frequency Linear LED Output Current Control Single-wire, S2Cwire Interface AAT3103-1: 16-step AAT3103-2: 8-step ON/OFF or PWM Interface AAT3103-4 10% LED Output Current Accuracy 3% LED Output Current Matching Low-current Shutdown Mode Built-in Short Circuit and Thermal Protection Automatic Soft-start 2x2.1mm SC70JW-10 Package Applications * * * * The AAT3103 is available in a 2x2.1mm thermally enhanced Pb-free 10-lead SC70JW-10 package. Cordless Phone Handsets Mobile Phone Handsets MP3 and PMP Players Digital Cameras Typical Application Input Voltage 2.7V to 5.5V OUT 3102-1 ND General Description IN C+ C IN 1F COUT 1F CP 1F OUT AAT3103-1 C OUT 1F C- EN/SET S2Cwire Interface D1 EN/SET D2 D2 WLEDs OSRAM LW M 678 or equivalent D1 RSET RSET 14.3k D3 AGND WLEDs OSRAM LW M 678 or equivalent Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 1 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Pin Descriptions Pin # Symbol 1 D1 2 3 4 OUT CC+ 5 IN 6 EN/SET (AAT3103-1/-2) EN/PWM (AAT3103-4) 7 RSET 8 AGND 9 D3 10 D2 Description LED1 Current Source Output. Connect LED1's anode to D1 and its cathode to AGND. If not used, connect to GND. Charge Pump Output. Bypass OUT to AGND with a 1F or larger ceramic capacitor. Charge Pump Capacitor Negative Node. Charge Pump Capacitor Positive Node. Connect a 1F ceramic capacitor between C+ and C-. Power source input. Connect IN to the power source, typically the battery. Bypass IN to AGND with a 1F or larger ceramic capacitor. LED Enable and serial control input. EN/SET is the ON/OFF control for the LED and the S2Cwire digital input for the AAT3103-1/-2 to control the LED brightness up to the maximum current set by RSET. LED ON/OFF and PWM (Pulse Width Modulation) control input. This logic input controls the LED outputs for the AAT3103-4. A PWM signal, ranging from 10% to 100% duty cycle, controls the LED current linearly between minimum and the full-scale output set by RSET. A 1% tolerance resistor from this pin to AGND sets the maximum LED current value. For optimal LED output current accuracy and matching in the AAT3103-1/-2/-4, a 14.3k resistor sets each full-scale output current to 20mA. Analog Ground. Connect this pin to the system's analog ground plane. LED3 Current Source Output. Connect LED3's anode to D3 and its cathode to AGND. If not used, connect to GND. LED2 Current Source Output. Connect LED2's anode to D2 and its cathode to AGND. If not used, connect to GND. Pin Configuration SC70JW-10 (Top View) 2 D1 1 10 D2 OUT 2 9 D3 C- 3 8 AGND C+ 4 7 RSET IN 5 6 EN/SET (EN/PWM) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Absolute Maximum Ratings1 Symbol TJ TLEAD Description IN, C+, C-, OUT, D1, D2, D3, and RSET Pin Voltages to AGND EN/SET or EN/PWM Pin Voltage to AGND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value Units -0.3 to 6.0 -0.3 to VIN + 0.3 -40 to 150 300 V V C C Value Units 625 160 mW C/W Thermal Information Symbol PD JA Description Maximum Power Dissipation Maximum Thermal Resistance2 2, 3 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 circuit board. 3. Derate 6.25mW/C above 40 C ambient temperature. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 3 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Electrical Characteristics1 IN = EN = 3.6V; CIN = 1F; COUT = 1F; CCP = 1F; RSET = 14.3k; TA=-40C to 85C unless otherwise noted. Typical values are at TA = 25C. Symbol Description Conditions Input Power Supply IN Input Voltage Range IIN Input Operating Current Min Typ Max Units 5.5 10 V 7.4 1.9 3 mA 4 6.8 1 A 2.7 IN = 5.5V; EN = IN; VD1 = VD2 = VD3 = 0V IN = 5.5V; EN = IN; ID1 = ID2 = ID3 = FS, excluding ID1-ID3; VD1 = VD2 = VD3 = IN - 1.5V Operating, ID1 = ID2 = ID3 = OPEN EN/SET or EN/PWM = GND IIN(SHDN) Input Shutdown Current Charge Pump Section IOUT OUT Maximum Output Current fOSC Charge Pump Oscillator Frequency VIN_(TH) Charge Pump Mode Hysteresis ID1 = ID2 = ID3 = 20mA tOUT LED Output Current Start-up Time EN/SET or EN/PWM = IN AAT3103-1/-2/-4: LED Current Source Outputs ID_(MAX) D1 - D3 Current Accuracy DATA = 1; VIN - VF = 1.5V. ID_(MAX) D1 - D3 Current Matching DATA = 1; VIN - VF = 1.5V D1 - D3 Current Accuracy ID_(DATA15) DATA = 15; VIN - VF = 1.5V (AAT3103-1 only) D1 - D3 Current Accuracy ID_(DATA8) DATA = 8; VIN - VF = 1.5V (AAT3103-2 only) D1 - D3 Current Accuracy ID_(10%) DC = 10%; VIN - VF = 1.5V (AAT3103-4 only) D1 - D3 Charge Pump Mode VD_(TH) ID1 = ID2 = ID3 = 20mA Transition Threshold VSET RSET Pin Voltage AAT3103-1/-2: EN/SET and S2Cwire Control VENH EN/SET Input High Threshold Voltage VENL EN/SET Input Low Threshold Voltage IEN(LKG) EN/SET Input Leakage Current EN/SET = IN = 5V tEN/SET(OFF) EN/SET Input OFF Timeout tEN/SET(LAT) EN/SET Input Latch Timeout tEN/SET(LOW) EN/SET Input Low Time tENSET(H-MIN) EN/SET Minimum High Time tENSET(H-MAX) EN/SET Maximum High Time AAT3103-4: EN/PWM Current Control VENH EN/PWM Input High Threshold Voltage VENL EN/PWM Input Low Threshold Voltage IEN(LKG) EN/PWM Input Leakage Current EN/PWM = IN = 5V tPWM(ON) PWM Control Turn-on Delay tEN/PWM EN/PWM Input OFF Timeout fPWM PWM Control Frequency Duty cycle = 80% 0.65 100 0.9 325 150 1.4 mA MHz mV s 18 20 3 22 mA % 1.0 1.34 1.61 mA 1.0 1.34 1.61 mA 1.14 2.5 mA 280 mV 1.18 1.22 1.4 0.4 1 500 500 75 -1 0.3 50 75 1.4 0.4 1 -1 110 0.15 1 50 V V V A s s s ns s V V A s ms kHz 1. The AAT3103 is guaranteed to meet performance specifications over the -40C to 85C operating temperature range and is assured by design, characterization and correlation with statistical process controls. 4 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Typical Characteristics Shutdown Current vs. Temperature Operating Current vs. Input Voltage (VD1 = VD2 = VD3 = 0V) 0.07 8.0 0.06 7.0 6.0 IQ (mA) ISHDN (A) 0.05 0.04 0.03 0.02 5.0 4.0 3.0 2.0 0.01 VIN = 5.5V VIN = 2.7V 0.00 -40 -15 10 35 60 -40C 25C 85C 1.0 0.0 2.5 85 3 3.5 Temperature (C) Operating Current vs. Input Voltage 21.0 4.1 20.5 Current (mA) IQ (mA) 4.2 3.9 3.8 85C 25C -40C 3 3.5 4 4.5 5 5.5 LED Current Matching vs. Temperature (No Load; D1, D2, D3 Open) 3.6 2.5 4 Input Voltage (V) 4.5 5 20.0 19.5 19.0 -40 5.5 D1 D2 D3 -15 Input Voltage (V) 10 35 60 85 28 33 Temperature (C) Efficiency vs. Input Voltage ILED Full Scale vs. RSET 35 100 90 28 70 ILED (mA) Efficiency (%) 80 60 50 40 21 14 30 ILED = 30mA,VF = 3.5V ILED = 20mA,VF = 3.2V ILED = 10mA,VF = 3.0V 20 10 0 2.7 3.1 3.5 3.9 4.3 Input Voltage (V) 4.7 5.1 7 5.5 0 8 13 18 23 RSET (k) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 5 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Typical Characteristics EN Input Low Threshold Voltage vs. Input Voltage 1.2 1.2 1.0 1.0 VENL (V) VENH (V) EN Input High Threshold Voltage vs. Input Voltage 0.8 0.6 -40C 25C 85C 0.4 0.2 2.7 3.1 3.5 3.9 4.3 4.7 5.1 0.8 0.6 -40C 25C 85C 0.4 0.2 2.7 5.5 3.1 3.5 Input Voltage (V) EN/SET Input Latch Timeout vs. Input Voltage tEN/SET(OFF) (V) tEN/SET(LAT) (V) 5.1 5.5 350 250 200 85C 25C -40C 150 100 2.7 3.1 3.5 3.9 4.3 4.7 5.1 300 250 200 85C 25C -40C 150 5.5 100 2.7 3.1 Input Voltage (V) VOUT (5V/div) 2.7V 3.2V 4.3 4.7 (VIN = 3.6V; 20mA/Dx) EN/SET (2V/div) 4.2V 3.9 Turn-Off from 2X Mode (VIN = 3.6V; 20mA/Dx) 0V 3.5 Input Voltage (V) Turn-On to 2X Mode 0V VD1 (2V/div) 0V IIN (200mA/div) 0A Time (200s/div) 6 4.7 400 300 VD1 (2V/div) IIN (200mA/div) 4.3 EN/SET Input Off Timeout vs. Input Voltage 350 EN/SET (2V/div) 3.9 Input Voltage (V) 0A Time (100s/div) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 5.1 5.5 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Typical Characteristics Turn-On to 1X Mode Output Ripple Waveform (VIN = 4.2V; 20mA/Dx) EN/SET (2V/div) 0V VOUT (2V/div) 0V VD1 (2V/div) IIN (200mA/div) 0V (2X Mode; 20mA/Dx) VOUT (AC) (20mV/div) 0A 0V VIN (AC) (20mV/div) 0V VD1 (AC) (20mV/div) 0V Time (200s/div) Time (1s/div) LED Current Transition LED Current Transition (VIN = 4.2V; 1.3mA to 20mA) EN/SET (2V/div) 0V VOUT (2V/div) VD1 (2V/div) IIN (50mA/div) EN/SET (2V/div) 4.2V 2.7V (VIN = 4.2V; 20mA to 1.3mA) 0V 4.2V VOUT (2V/div) 3.2V 3.2V VD1 (2V/div) IIN (50mA/div) 0A Time (100s/div) 2.7V 0A Time (100s/div) Input Current vs. Input Voltage Input Current (mA) 250 ILED = 30mA ILED = 20mA ILED = 10mA 200 150 VIN Rising VIN Falling 100 50 0 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 Input Voltage (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 7 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Functional Block Diagram C+ IN C- OUT Two-Mode CP Control D1 D2 VF Monitoring 3 D3 AGND IREF EN/SET (EN/PWM) S2Cwire Control (PWM Control) Functional Description The AAT3103 is a low-cost charge-pump solution designed to drive up to three WLEDs. The charge pump operates from a 2.7V to 5.5V power source and converts it to voltage levels necessary to drive the LEDs. LED current is individually controlled through integrated current sources powered from the output of the charge pump. Low 1x charge-pump output resistance and low-drop voltage current sources allow the charge pump to stay in 1x mode with an input voltage as low as 3.75V and LED forward voltages as high as 3.2V with 20mA LED current. Once in 2x mode, the charge pump monitors the input supply voltage and automatically switches back to 1x mode when there is sufficient input voltage. The AAT3103 requires only four external components: one 1F ceramic capacitor for the charge pump flying capacitors (CP), one 1F ceramic input capacitor (CIN), one 1F ceramic output capacitor (COUT) and a resistor 8 DAC RSET (RSET) to set the maximum LED current. The three constant current outputs of the AAT3103 (D1 to D3) can drive three individual LEDs with a maximum current of 30mA each. Skyworks' S2Cwire serial interface enables the AAT3103-1/-2 and changes the current source magnitudes through the EN/SET pin. The AAT3103-4 uses an external PWM signal to enable the IC and control the brightness of the LEDs. Constant Current Control Using RSET The maximum current is programmed by an external resistor at the RSET pin. With a 14.3k external resistor at the RSET pin, the AAT3103 includes an integrated serial LED current control that sets the full-scale LED current between 20mA and 0.67mA. The full-scale LED current can be set higher or lower than 20mA; see Table 4. For maximum accuracy, a 1% tolerance resistor is recommended. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Part Number Descriptions Part Number Interface Current Control, Inverting AAT3103IJQ-1 AAT3103IJQ-2 AAT3103IJQ-4 S2Cwire S2Cwire PWM 16-step 8-step Linear changed quickly and easily. Also the non-pulsating LED current reduces system noise and improves LED reliability. The S2Cwire interface relies on the number of rising edges to the EN/SET pin to set the register. A typical write protocol is a burst of EN/SET rising edges, followed by a pause with EN/SET held high for at least tLAT (500s). The programmed current is then seen at the current source outputs. When EN/SET is held low for an amount of time longer than tOFF (500s), the AAT3103 enters into shutdown mode and draws less than 1A from the input and the internal data register is reset to zero. S2Cwire Serial Interface (AAT3103-1/-2 only) The LED output current of the AAT3103-1/-2 is controlled by Skyworks' S2Cwire serial interface. Since the LED current is programmable, no PWM or additional control circuitry is needed to control the LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to "set it and forget it." With its high-speed serial interface (1MHz data rate), the LED current can be The AAT3103-1/-2's serial interface reduces the LED current on each rising pulse of the enable input. If the AAT3103 is in shutdown, the first rising edge of the EN/ SET input turns on the LED driver to the maximum current. Successive rising edges decrease the LED current as shown in Table 1 and Figure 2 for the AAT3103-1. For the AAT3103-2, Table 2 and Figure 3 illustrate an 8-step LED current control profile. . THI TLO TOFF TLAT EN/SET 1 2 n-1 Data Reg n 16 0 n 0 Figure 1: S2Cwire Serial Interface Timing. EN Rising Edges D1-D3 Current (mA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 20.1 18.8 17.5 16.1 14.8 13.4 12.1 10.7 9.4 8.1 6.7 5.4 4.0 2.7 1.34 0.67 25 Dx LED Current (mA) S2C Data 20 15 10 5 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 S2C Wire Interface Data Code Figure 2: AAT3103-1 Current Control Profile, RSET = 14.3k. Table 1: AAT3103-1 LED Current Settings, RSET = 14.3k. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 9 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Data EN Rising Edges D1-D3 Current (mA) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 20.1 17.5 14.8 12.1 9.4 6.7 4.0 1.34 cycle of the PWM signal from 100% (logic high) to 10%, the LED current can be programmed from 20mA to 2.6mA. To save power when not used, the AAT3103-4 can be shut down by holding the EN/PWM pin low for 500s. Lastly, Table 3 and Figure 4 illustrate the AAT3103-4's LED current control profile as a function of a PWM control signal. EN/PWM Duty Cycle D1-D3 Current (mA) 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 20.2 18.2 16.2 14.3 12.3 10.4 8.5 6.55 4.6 2.6 Table 2: AAT3103-2 LED Current Settings, RSET = 14.3k. Dx LED Current (mA) 25 20 15 10 Table 3: AAT3103-4 LED Current Settings, RSET = 14.3k, fPWM = 25kHz. 5 0 1 2 3 4 5 6 7 8 S C Wire Interface Data Code 25 Figure 3: AAT3103-2 Current Control Profile, RSET = 14.3k. PWM Control (AAT3103-4 only) PWM (Pulse Width Modulation) is a technique of controlling LED brightness by modulating the conduction duty cycle of the LED current. LED brightness is determined by the PWM duty cycle and FS (Full Scale) and LSB (the least LED current). The FS LED current is determined by RSET. The LSB LED current value is equal to the FS value divided by 30. A PWM control signal can be applied into the EN/PWM pin of the AAT3103-4. By changing the duty 10 Dx LED Current (mA) 2 20 15 10 5 0 100 90 80 70 60 50 40 30 20 10 PWM Duty Cycle (%) Figure 4: AAT3103-4 Current Control Profile, RSET = 14.3k, fPWM = 25kHz. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver LED Selection The AAT3103 is specifically intended for driving WLEDs. However, the device design will allow the AAT3103 to drive most types of LEDs with forward voltage specifications ranging from 2.2V to 4.7V. LED applications may include mixed arrangements for display backlighting, keypad display, and any other application needing a constant current sink generated from a varying input voltage. Since the D1 to D3 constant current sources are matched with negligible supply voltage dependence, the constant current channels will be matched regardless of the specific LED forward voltage (VF) levels. The internal charge pump and low dropout current sources in the AAT3103 maximize performance and make it capable of driving LEDs with high forward voltages. Multiple channels can be combined to obtain a higher LED drive current without complication. Constant Current Setting The LED full scale current is controlled by the RSET resistor. The following formula can be used to calculate the AAT3103-1/2/4 full scale LED current: ILED_FS = 1.2 * 4 * 60 RSET Table 4 shows the RSET resistor value for the AAT3103-1/2/4 for various LED full-scale current levels. For maximum accuracy, a 1% tolerance resistor is recommended. ILED_FS (mA) RSET (k) 30.2 20.1 15.1 10.0 9.53 14.3 19.1 28.7 Table 4: Maximum LED Current and RSET Resistor Values (1% Resistor Tolerance) for the AAT3103. The S2C interface rising edges control the LED current from full scale to the LSB. For the AAT3103-1, 16 steps are employed. Figure 5 shows the LED current of the AAT3103-1 at different RSET values. 35 Dx LED Current (mA) Applications Information RSET = 9.53k 30 RSET = 14.3k 25 20 RSET = 19.1k 15 RSET = 28.7k 10 5 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 S2C Wire Interface Data Code Figure 5: AAT3103-1 LED Current Control Profile at Different RSET Values. Device Switching Noise Performance The AAT3103 operates at a fixed frequency of approximately 0.9MHz to control noise and limit harmonics that can interfere with the RF operation of mobile communication devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to-peak, typically ten times less than inductor-based DC/DC boost converter WLED backlight solutions. The AAT3103's softstart feature prevents noise transient effects associated with inrush currents during start-up of the charge pump circuit. Shutdown To activate the shutdown operation, the EN/SET input for the AAT3103-1/-2 should be pulsed low for longer than tOFF (500s). For the 3103-4 PWM options, shutdown operation is enabled when the EN/PWM input is pulsed low longer than 500s. In this state, the AAT3103 typically draws less than 1A from the input. Registers are reset to 0 in shutdown. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 11 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Power Efficiency and Device Evaluation The charge pump efficiency discussion in the following sections accounts only for efficiency of the charge pump section itself. Due to the unique circuit architecture and design of the AAT3103, it is very difficult to measure efficiency in terms of a percent value comparing input power over output power. Since the AAT3103 outputs are pure constant current sources and typically drive individual loads, it is difficult to measure the output voltage for a given output pin to derive an overall output power measurement. For any given application, WLED forward voltage levels can differ, yet the output drive current will be maintained as a constant. This makes quantifying output power a difficult task when taken in the context of comparing to other WLED driver circuit topologies. A better way to quantify total device efficiency is to observe the total input power to the device for a given LED current drive level. The best WLED driver for a given application should be based on trade-offs of size, external component count, reliability, operating range, and total energy usage...not just % efficiency. The AAT3103 efficiency may be quantified under very specific conditions and is dependent upon the input voltage versus the outputs of D1, D2 and D3 for a given constant current setting. Depending on the combination of VIN and voltages sensed at the current sources, the device will operate in load switch mode. When any one of the voltages sensed at the current sources nears dropout, the device will operate in 2x charge pump mode. The ideal efficiency () in 1x charge-pump mode can be expressed as: POUT VF * ILED VF * ILED VF = P = V *I =V *I VIN IN IN IN IN OUT -or- VF (%) = V * 100 IN For a charge pump LED driver with VF of 3.2V and 4.2V input voltage, the theoretical efficiency is 76%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 73%. 2x Charge Pump Mode Efficiency The AAT3103 contains a charge pump which will boost the input supply voltage in the event where VIN is less than the voltage required to supply the output. The efficiency () can be simply defined as a linear voltage regulator with an effective output voltage that is equal to one half of the input voltage. Efficiency () for an ideal 2x charge pump can typically be expressed as the output power divided by the input power. = In addition, with an ideal 2x charge pump, the output current may be expressed as 1/3 of the input current. The expression to define the ideal efficiency () can be rewritten as Each of these modes will yield different efficiency values. Refer to the following two sections for explanations for each operational mode. The AAT3103 1x mode is operational at all times and functions alone to enhance device power conversion efficiency when VIN is higher than the voltage across the load. When in 1x mode, voltage conversion efficiency is defined as output power divided by input power. 12 POUT VF * ILED VF * ILED VF = P = V *I =V *2*I 2*V IN IN IN IN OUT IN -or- 1x Mode Efficiency = PF PIN PF PIN VF (%) = 2 * V * 100 IN For a charge pump LED current source driver with VF of 3.2V and 2.7V input voltage, the theoretical efficiency is 59%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 57%. Efficiency will decrease substantially as load current drops below 1mA or when the voltage level at VIN approaches the voltage level at VOUT. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Additional Applications performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used; in general, low ESR may be defined as less than 100m. A value of 1F for all three capacitors is a good starting point when choosing capacitors. The current sources of the AAT3103 can be combined to drive higher current levels through a single LED. As an example, a single LED can be driven at 60mA total by combining together the D1-D3 outputs as shown in Figure 6. Capacitor Characteristics For lower-cost applications, the flying capacitor can be removed. This will force the AAT3103 to operate in 1x mode. To maintain regulated LED current, the input supply voltage must be greater than the charge pump's dropout voltage and the current source voltage drop in 1x mode. For example, to power 3.0V VF with 20mA LED current, VIN should be greater than 4.0V as shown in Figure 7. Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3103. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is non-polarized. Low ESR ceramic capacitors help to maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Capacitor Selection Careful selection of the three external capacitors CIN, CP, and COUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum D1 C2 1F 1 2 C1 1F 3 4 5 VIN U1 AAT3103 D1 D2 OUT D3 9 8 AGND 7 RSET CC+ IN 10 EN/SET 6 R1 14.3k C3 1F EN/SET Figure 6: Higher Current, Single LED Application. C2 1F 1 2 3 4 5 VIN U1 AAT3103 D1 OUT C- C+ IN C3 1F 10 D2 9 D3 AGND 8 D3 D2 D1 7 RSET 6 EN/SET R1 14.3k EN/SET Figure 7: Lower Cost 1x Mode Application. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 13 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Evaluation Board Schematic J1 DC+ C DC- C2 1F D3 JP2 JP1 C1 1F C3 1F D2 AAT3103-1 White LED Driver D1 JP3 JP4 U1 AAT3103 1 2 3 4 5 D1 D2 OUT D3 CAGND C+ RSET IN EN/SET JP5 10 9 8 7 6 R1 14.3k S2Cwire Microcontroller R2 20k R5 R4 R3 1k 1k 1k S1 UP U2 PIC12F675 1 2 3 4 VDD GP5 GP4 GP3 VSS GP0 GP1 GP2 S2 DOWN S3 CYCLE VR1 10k 8 7 6 5 R6 330 LED1 Green Figure 8: AAT3103 Evaluation Board Schematic. 14 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 R7 C4 330 0.1F LED2 Red DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Evaluation Board Layout Figure 9: AAT3103 Evaluation Board Top Side PCB Layout. Figure 10: AAT3103 Evaluation Board Bottom Side PCB Layout. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 15 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Ordering Information Package Interface Current Control, Inverting Marking1 Part Number (Tape and Reel)2 SC70JW-10 SC70JW-10 SC70JW-10 S Cwire S2Cwire PWM 16-step 8-step Linear 1DXYY AAT3103IJQ-1-T1 AAT3103IJQ-2-T1 AAT3103IJQ-4-T1 2 2TXYY Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04-0074. Package Information SC70JW-10 2.20 0.20 1.75 0.10 0.40 BSC 0.225 0.075 Top View 0.100 7 3 0.45 0.10 4 4 0.05 0.05 0.15 0.05 1.10 MAX 0.85 0.15 2.00 0.20 2.10 0.30 Side View End View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 16 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 DATA SHEET AAT3103 Three-Channel Charge-Pump LED Driver Copyright (c) 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 202123A * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * July 2, 2012 17