MBR6045WT - ON Semiconductor

July, 2014 − Rev. 10 1Publication Order Number:

MBR6045WT/D

MBR6045WTG

Switch Mode

Power Rectifier

The Switch Mode power rectifier employs the use of the Schottky

Barrier principle with a Platinum barrier metal.

Features

•Dual Diode Construction; Terminals 1 and 3 May Be Connected for

Parallel Operation at Full Rating

•45 V Blocking Voltage

•Low Forward Voltage Drop

•Guard−ring for Stress Protection and High dv/dt Capability (> 10 V/ns)

•175°C Operating Junction Temperature

•These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS

Compliant*

Mechanical Characteristics

•Case: Epoxy, Molded

•Weight: 4.3 Grams (Approximately)

•Finish: All External Surfaces Corrosion Resistant and Terminal

Leads are Readily Solderable

•Lead Temperature for Soldering Purposes:

260°C Max. for 10 Seconds

MAXIMUM RATINGS

Rating Symbol Max Unit

Peak Repetitive Reverse Voltage

Working Peak Reverse Voltage

DC Blocking Voltage

VRRM

VRWM

45 V

Average Rectified Forward Current

(Rated VR, TC = 125°C) Per Diode

Per Device

IF(AV) 30

Peak Repetitive Forward Current,

(Rated VR, Square Wave,

20 kHz, TC = 90°C) Per Diode

IFRM 60 A

Non−Repetitive Peak Surge Current

(Surge Applied at Rated Load Conditions

Halfwave, Single Phase, 60 Hz)

IFSM 500 A

Peak Repetitive Reverse Current

(2.0 ms, 1.0 kHz) IRRM 2.0 A

Storage Temperature Range Tstg −65 to +175 °C

Operating Junction Temperature (Note 1) TJ−65 to +175 °C

Peak Surge Junction Temperature

(Forward Current Applied) TJ(pk) 175 °C

Voltage Rate of Change dv/dt 10,000 V/ms

Stresses exceeding those listed in the Maximum Ratings table may damage the

device. If any of these limits are exceeded, device functionality should not be

assumed, damage may occur and reliability may be af fected.

1. The heat generated must be less than the thermal conductivity from

Junction−to−Ambient: dPD/dTJ < 1/RqJA.

*For additional information on our Pb−Free strategy and soldering details, please

download the ON Semiconductor Soldering and Mounting Techniques

Reference Manual, SOLDERRM/D.

A = Assembly Location

Y = Year

WW = Work Week

G = Pb−Free Package

http://onsemi.com

TO−247

CASE 340AL

SCHOTTKY BARRIER

RECTIFIER

60 AMPERES, 45 VOLTS

2, 4

Device Package Shipping

ORDERING INFORMATION

MBR6045WTG TO−247

(Pb−Free) 30 Units/Rail

MARKING DIAGRAM

MBR6045WT

AYWWG

MBR6045WTG

http://onsemi.com

THERMAL CHARACTERISTICS (Per Diode)

Rating Symbol Max Unit

Thermal Resistance, Junction−to−Case RqJC 1.0 °C/W

ELECTRICAL CHARACTERISTICS (Per Diode)

Instantaneous Forward Voltage (Note 2)

@ IF = 30 Amps, TC = 25°C

@ IF = 30 Amps, TC = 125°C

@ IF = 60 Amps, TC = 25°C

VF0.62

0.55

0.75

Volts

Instantaneous Reverse Current (Note 2)

@ Rated DC Voltage, TC = 25°C

@ Rated DC Voltage, TC = 100°C

IR1.0

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

2. Pulse Test: Pulse Width = 300 ms, Duty Cycle < 2.0%

TYPICAL ELECTRICAL CHARACTERISTICS

Figure 1. Typical Reverse Current Figure 2. Typical Forward Voltage

VR, REVERSE VOLTAGE (VOLTS)

IR, REVERSE CURRENT (mA)

vF, INSTANTANEOUS FORWARD VOLTAGE (mV)

iF, INSTANTANEOUS FORWARD CURRENT (AMPS)

1000

100

0.1

0.01 50403020100

TC = 150°C

TC = 100°C

TC = 25°C

100

1100 200 300 400 500 600 700 800

150°C 100°C TC = 25°C

MBR6045WTG

http://onsemi.com

PACKAGE DIMENSIONS

TO−247

CASE 340AL

ISSUE A

0.25 MBA

cA1

123

0.635 MBA

SEATING

PLANE

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. SLOT REQUIRED, NOTCH MAY BE ROUNDED.

4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH.

MOLD FLASH SHALL NOT EXCEED 0.13 PER SIDE. THESE

DIMENSIONS ARE MEASURED AT THE OUTERMOST

EXTREME OF THE PLASTIC BODY.

5. LEAD FINISH IS UNCONTROLLED IN THE REGION DEFINED BY

L1.

6. ∅P SHALL HAVE A MAXIMUM DRAFT ANGLE OF 1.5° TO THE

TOP OF THE PART WITH A MAXIMUM DIAMETER OF 3.91.

7. DIMENSION A1 TO BE MEASURED IN THE REGION DEFINED

BY L1.

DIM MIN MAX

MILLIMETERS

D20.30 21.40

E15.50 16.25

A4.70 5.30

b1.00 1.40

b2 1.65 2.35

e5.45 BSC

A1 2.20 2.60

c0.40 0.80

L19.80 20.80

Q5.40 6.20

E2 4.32 5.49

L1 3.50 4.50

P3.55 3.65

S6.15 BSC

b4 2.60 3.40

NOTE 6

NOTE 7

NOTE 4

NOTE 3

NOTE 5

E2/2

NOTE 4

UBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

MBR6045WT/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your loc

Sales Representative

ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.

SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed

at www.onsemi.com/site/pdf/Patent−M arking.pdf. S CILLC r eserves the r ight to make c hanges without further notice t o any p roducts h erein. S CILLC makes no w arranty, representation

or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and

specifically disclaims any and all l iabilit y, including without limitation special, consequential or i ncident al d amages. “Typical” parameters which m ay b e p r ovided i n SCILLC data sheets

and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each

customer application b y c ust omer’s technical e xperts. SCILLC does not c onvey a ny license under its p atent rights n or t he r ights o f o t hers. SCILLC pr oducts a r e n ot d esigned, i ntended,

or authorized for use as c omponent s i n s yst ems i nt ended f or s urgic al i m plant i nt o the body, or other applications int ended t o s upport o r s ust ain life, or for any ot her a pplication i n w hich

the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or

unauthorized application, Buyer shall indemnify and hold SCILLC an d it s officers, employees, subsidiaries, affiliates, and distribut ors harmless against all claims, costs, damages, and

expenses, and r easonable a ttorney f ees a rising o ut of, directly or i ndirectly, any claim o f p ersonal i njury o r d eath a ssociated w ith s uch u nint ended o r u nauthorized u se, e ven if such claim

alleges that SCILLC was negligent regarding the d esign or manufacture of the p art. S CILLC i s a n E qual O pportunity/Af firmative Act ion Employer. T his literature is s ubject t o all applicable