13
ELESTA relays GmbH, Heuteilstrasse 18,
CH - 7310 Bad Ragaz, Switzerland
Phone: +41 (0)81 303 54 00
Fax: +41 (0)81 303 54 01
E-Mail: admin@elestarelays.com
Internet: http://www.elestarelays.com
SGR282Z
Double or reinforced insulation
Control side Output side
SGR282Z
30,2 12,7
25,6
3,7
2,6
15
5
5
2,6
1
7,5
0,3
2,5 / 2,54
Ø
1,3
[mm]
10 000
1000
100
10
10
1.0
0.5
0.1
DC 1: 24V
5.0
AC 1: 230V
AC 15: 230V
DC 13: 24V
Switching current (A)
No. of operations x 1000
Current (A)
Voltage (VDC)
0,6
0,4
0,1
0,3
0,2
0,8
1
2
3
4
6
8
050 100 150 200 250
12
Standard coils for direct current
(other voltages on request)
- PCB relay with forcibly guided contacts
- Protective separation between coil and
contacts (leakage and creepage distances
> 14mm); protective separation diagonally
between left and right contact side (leakage
and creeping distances > 5.5mm)
- EN 50205, type B
- 2 CO contacts
- Mean coil power 1 W
- Holding power 0.31 W
Contact material AgCuNi
Type of contact Single contact
Rated switching capacity 250VAC 6A AC1 1’500VA
Electr. life AC1 (360 cycles/h) approx.100’000
Inrush current max. 15A for 20ms
Switching voltage range 50 to 250 VDC/VAC
Switching current range* 20mA to 6A
Switching current range** 10mA to 6A
Switching capacity range* 0.12VA(W) to 1’500VA
Switching capacity range** 0.06VA(W) to 1’500VA
Contact resistance (as delivered) < 100mΩ / 28 V / 100mA
* Guide values
** Values for AgCuNi + 4-6 μm Au
Nominal voltage
VDC
Min. pick-up
voltage at 20°C
Drop-out voltage
at 20 °C
Nominal current
in mA
Resistance in
Ohm at 20 °C
Tolerance in %
5 3,75 > 0,5 181,8 27,5 ± 10
6 4,5 > 0,6 166,6 36 ± 10
12 9,0 > 1,2 85,7 140 ± 10
18 13,5 > 1,8 66,6 270 ± 10
24 18,0 > 2,4 33,3 720 ± 10
48 36,0 > 4,8 20,8 2’300 ± 10
60 45,0 > 6,0 13,6 4’400 ± 13
110 82,5 > 11,0 11,0 10’000 ± 15
Circuit diagram (view on relay upper side)
Tests, regulations
Approvals SEV, UL, cUL, TÜV
UL File E188953 Sec. 1
Insulation class IEC 60664-1 250VAC
Protection class II VDE 0106
Fire protection requirements UL 94 / V1
Mechanical life > 50 x 106 operations
Switching frequency, mechanical 20Hz
Response time typically 12ms
Drop-out time*** typically 5ms
Bounce time of NO contact typically 4ms
Bounce time of NC contact typically 8ms
Vibration resistance 10-55Hz, AK 10g, RK 1.5g
Test voltage coil/contacts 5’000Veff 1min
Test voltage
contact set/contact set 4’000Veff 1min
Test voltage contact open 1’500Veff 1min
Insulation resistance 1011 Ω
Creepage resistance CTI 550
Weight approx. 20g
Mounting position any
Ambient temperature -40°C to +70°C
Type of protection RT II / RT III optionally
Solder bath temperature 270°C/5s
Thermal resistance 50K/W
Temperature limit for coil 120°C
Pollution degree 2
Resistance to 1‘000A SCPD 6A
short circuiting gL/gG (pre-fuse)
*** without spark suppression
Options, accessories
Contact material SGR282Z..VDC AgCuNi
+4 - 6μm Au
PCB socket, DIN rail socket see page 29
Wash-resistant with O-Ring
Sealed RT III on request
Insulation terms
Coil/contacts: Double or reinforced insulation
> 14mm
Left to right contact side:
Double or reinforced insulation > 5.5mm
Gold contacts with 4-6μm layer thickness
When high voltages and currents are
switched, the layer of gold is destroyed
already after a few switching operations.
Once the gold layer is damaged due to the
switching of high loads, such a contact must
not be used any more for signal and control
current circuits.
Safe contact making is then only possible at
high loads with the formation of sparks.
Contact lifetime for AgCuNi
Max. switching characteristics
(acc. to DIN EN 60947-5-1 table C2):
AC 15: 230V/3A, DC13: 24V/4A
UL 508: C300
Load limit curve with direct current
1) Inductive load, L/R 40 ms
2) Resistive load
Ambient temperature °C
U
U
B
N
0
040 60
2,0
1,5
1,0
0,5
1
2
80 100
20
Excitation voltage range
1) Max. excitation voltage with contact load < 2A
2) Min. excitation voltage (guaranteed values)
without previous operation
No heat accumulation due to intrinsic heating
of other components.
Continuous duty 100%.
Ordering example
Relay data General data Diagrams
Maximal contact load at AC 1 with 230V:
2 contacts each with 6A
Type designation
Coil voltage
Gold plating 4 - 6μm Au
Wash-resistant / with O-ring
SGR282Z 24VDC AU6 08