Preliminary Information H EE GEN FR ALO CAT1024, CAT1025 Supervisory Circuits with I2C Serial 2k-bit CMOS EEPROM and Manual Reset LE FEATURES 16-Byte page write buffer Precision power supply voltage monitor Built-in inadvertent write protection A D F R E ETM -- WP pin (CAT1025) -- 5V, 3.3V and 3V systems 1,000,000 Program/Erase cycles -- Five threshold voltage options Manual reset input Active high or low reset 100 year data retention -- Valid reset guaranteed at VCC = 1V 8-pin DIP, SOIC, TSSOP, MSOP & TDFN 400kHz I2C bus (3x4.9mm & 3x3mm foot print) packages 2.7V to 5.5V operation Industrial and extended temperature ranges Low power CMOS technology DESCRIPTION The CAT1024 and CAT1025 are complete memory and supervisory solutions for microcontroller-based systems. A 2k-bit serial EEPROM memory and a system power supervisor with brown-out protection are integrated together in low power CMOS technology. Memory interface is via a 400kHz I2C bus. The CAT1025 provides a precision VCC sense circuit and two open drain outputs: one (RESET) drives high and the other (RESET) drives low whenever VCC falls below the reset threshold voltage. The CAT1025 also has a Write Protect input (WP). Write operations are disabled if WP is connected to a logic high. The CAT1024 also provides a precision VCC sense circuit, but has only a RESET output and does not have a Write Protect input. The power supply monitor and reset circuit protect memory and system controllers during power up/down and against brownout conditions. Five reset threshold voltages support 5V, 3.3V and 3V systems. If power supply voltages are out of tolerance reset signals become active, preventing the system microcontroller, ASIC or peripherals from operating. Reset signals become inactive typically 200 ms after the supply voltage exceeds the reset threshold level. With both active high and low reset signals, interface to microcontrollers and other ICs is simple. In addition, the RESET pin or a separate input, MR, can be used as an input for push-button manual reset capability. The CAT1024/25 memory features a 16-byte page. In addition, hardware data protection is provided by a VCC sense circuit that prevents writes to memory whenever VCC falls below the reset threshold or until VCC reaches the reset threshold during power up. Available packages include an 8-pin DIP and a surface mount 8-pin SO, 8-pin TSSOP, 8-pin TDFN and 8-pin MSOP packages. The TDFN package thickness is 0.8mm maximum. TDFN footprint options are 3x3mm or 3x4.9mm (MSOP pad layout). PIN CONFIGURATION DIP Package (P, L) SOIC Package (S, V) TSSOP Package (U, Y) MSOP Package (R, Z) MR 1 RESET 2 CAT1024 8 VCC 7 NC CAT1024 RESET VCC 8 1 MR NC 7 2 RESET 3 NC 4 VSS CAT1024 3 NC SCL 5 SDA SDA 5 4 VSS SDA 5 8 VCC 7 WP VCC 8 1 MR 2 RESET MR 1 VSS 4 2 7 MR 6 VSS 4 RESET 3 NC 1 8 SCL 6 SCL CAT1025 VCC 6 NC 3 RESET 2 (Bottom View) (Bottom View) TDFN Package: 3mm x 3mm TDFN Package: 3mm x 4.9mm 0.8mm maximum height - (RD4, ZD4) 0.8mm maximum height - (RD2, ZD2) WP 7 CAT1025 2 RESET WP 7 6 SCL SCL 6 3 RESET SCL 6 5 SDA SDA 5 4 VSS SDA 5 (c) 2003 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 MR VCC 8 CAT1025 3 RESET 4 V SS Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information Threshold Voltage Options BLOCK DIAGRAM -- CAT1024, CAT1025 Part Dash Minimum Number Threshold EXTERNAL LOAD SENSE AMPS SHIFT REGISTERS DOUT ACK VCC VSS SDA WORD ADDRESS BUFFERS COLUMN DECODERS START/STOP LOGIC -45 4.50 4.75 -42 4.25 4.50 -30 3.00 3.15 -28 2.85 3.00 -25 2.55 2.70 2kbit EEPROM XDEC WP* Maximum Threshold CONTROL LOGIC DATA IN STORAGE HIGH VOLTAGE/ TIMING CONTROL RESET Controller Precision MR Vcc Monitor * RESET STATE COUNTERS SCL SLAVE ADDRESS COMPARATORS RESET *CAT1025 Only PIN FUNCTIONS OPERATING TEMPERATURE RANGE Pin Name Function Industrial -40C to 85C NC No Connect Extended -40C to 125C RESET Active Low Reset Input/Output VSS Ground SDA Serial Data/Address SCL Clock Input RESET Active High Reset Output (CAT1025 only) VCC Power Supply WP Write Protect (CAT1025 only) MR Manual Reset Input Doc. No. 3008, Rev. I 2 Preliminary Information CAT1024, CAT1025 PIN DESCRIPTION RESET/RESET RESET: RESET OUTPUTS RESET (RESET CAT1025 Only) These are open drain pins and RESET can be used as a manual reset trigger input. By forcing a reset condition on the pin the device will initiate and maintain a reset condition. The RESET pin must be connected through a pull-down resistor, and the RESET pin must be connected through a pull-up resistor. SDA: SERIAL DATA ADDRESS The bidirectional serial data/address pin is used to transfer all data into and out of the device. The SDA pin is an open drain output and can be wire-ORed with other open drain or open collector outputs. MR: MANUAL RESET INPUT Manual Reset input is a debounced input that can be connected to an external source for Manual Reset. Pulling the MR input low will generate a Reset condition. Reset outputs are active while MR input is low and for the reset timeout period after MR returns to high. The input has an internal pull-up resistor. WP (CAT1025 Only): WRITE PROTECT INPUT When tied to VSS or left unconnected write operations to the entire array are allowed. When tied to VCC, the entire array is protected. This input has an internal pull down resistor. SCL: SERIAL CLOCK Serial clock input. CAT10XX FAMILY OVERVIEW Device Manual Reset Input Pin Watchdog Watchdog Monitor Pin Write Protection Pin Independent Auxiliary Voltage Sense RESET: Active High and LOW EEPROM CAT1021 SDA 2k CAT1022 SDA 2k CAT1023 WDI 2k CAT1024 2k CAT1025 2k CAT1026 2k CAT1027 WDI 2k For supervisory circuits with embedded 16k EEPROM, please refer to the CAT1161, CAT1162 and CAT1163 data sheets. 3 Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information ABSOLUTE MAXIMUM RATINGS Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Temperature Under Bias ................. -55C to +125C Storage Temperature ....................... -65C to +150C Voltage on any Pin with Respect to Ground(1) ............ -2.0V to +VCC +2.0V Note: (1) The minimum DC input voltage is -0.5V. During transitions, inputs may undershoot to -2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. (2) Output shorted for no more than one second. No more than one output shorted at a time. VCC with Respect to Ground ............... -2.0V to +7.0V Package Power Dissipation Capability (TA = 25C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300C Output Short Circuit Current(2) ........................ 100 mA D.C. OPERATING CHARACTERISTICS VCC = +2.7V to +5.5V and over the recommended temperature conditions unless otherwise specified. Symbol Parameter Test Conditions Min ILI Input Leakage Current VIN = GND to Vcc ILO Output Leakage Current VIN = GND to Vcc ICC1 Power Supply Current (Write) ICC2 Ma x Units -2 10 A -10 10 A fSCL = 400kHz VCC = 5.5V 3 mA Power Supply Current (Read) fSCL = 400kHz VCC = 5.5V 1 mA ISB Standby Current Vcc = 5.5V, VIN = GND or Vcc 40 A VIL(1) Input Low Voltage -0.5 0.3 x Vcc V VIH(1) Input High Voltage 0.7 x Vcc Vcc + 0.5 V VOL Output Low Voltage (SDA, RESET) IOL = 3mA VCC = 2.7V 0.4 V VOH Output High Voltage (RESET) IOH = -0.4mA VCC = 2.7V Vcc 0.75 CAT102x-45 (VCC = 5V) 4.50 4.75 CAT102x-42 (VCC = 5V) 4.25 4.50 CAT102x-30 (VCC = 3.3V) 3.00 3.15 CAT102x-28 (VCC = 3.3V) 2.85 3.00 CAT102x-25 (VCC = 3V) 2.55 2.70 VTH Reset Threshold Typ V V VRVALID Reset Output Valid VCC Voltage 1.00 V VRT(2) Reset Threshold Hysteresis 15 mV Notes: 1. VIL min and VIH max are reference values only and are not tested. 2. This parameter is tested initially and after a design or process change that affects the parameter. Not 100% tested. Doc. No. 3008, Rev. I 4 Preliminary Information CAT1024, CAT1025 CAPACITANCE TA = 25C, f = 1.0 MHz, VCC = 5V Symbol COUT (1) CIN(1) Test Test Conditions Max Units VOUT = 0V 8 pF VIN = 0V 6 pF Output Capacitance Input Capacitance AC CHARACTERISTICS VCC = 2.7V to 5.5V and over the recommended temperature conditions, unless otherwise specified. Memory Read & Write Cycle2 Symbol Parameter fSCL Min Max Units Clock Frequency 400 kHz tSP Input Filter Spike Suppression (SDA, SCL) 100 ns tLOW Clock Low Period 1.3 s tHIGH Clock High Period 0.6 s tR(1) SDA and SCL Rise Time 300 ns tF(1) SDA and SCL Fall Time 300 ns tHD;STA Start Condition Hold Time 0.6 s tSU;STA Start Condition Setup Time (for a Repeated Start) 0.6 s tHD;DAT Data Input Hold Time 0 ns tSU;DAT Data Input Setup Time 100 ns tSU;STO Stop Condition Setup Time 0.6 s tAA SCL Low to Data Out Valid tDH Data Out Hold Time 50 ns tBUF(1) Time the Bus must be Free Before a New Transmission Can Start 1.3 s tWC(3) Write Cycle Time (Byte or Page) 900 5 ns ms Notes: 1. This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested. 2. Test Conditions according to "AC Test Conditions" table. 3. The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus interface circuits are disabled, SDA is allowed to remain high and the device does not respond to its slave address. 5 Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information RESET CIRCUIT AC CHARACTERISTICS Symbol Parameter Test Conditions Min Typ Max Units tPURST Reset Timeout Note 2 130 200 270 ms tRPD VTH to RESET Output Delay Note 3 5 s tGLITCH VCC Glitch Reject Pulse Width Note 4, 5 30 ns MR Glitch Manual Reset Glitch Immunity Note 1 100 ns tMRW MR Pulse Width Note 1 tMRD MR Input to RESET Output Delay Note 1 5 s 1 s Max Units POWER-UP TIMING5,6 Test Conditions Symbol Parameter Min Typ tPUR Power-Up to Read Operation 270 ms tPUW Power-Up to Write Operation 270 ms AC TEST CONDITIONS Parameter Test Conditions Input Pulse Voltages 0.2VCC to 0.8VCC Input Rise and Fall Times 10 ns Input Reference Voltages 0.3VCC, 0.7VCC Output Reference Voltages 0.5VCC Output Load Current Source: IOL = 3mA; CL = 100pF RELIABILITY CHARACTERISTICS Symbol Parameter Reference Test Method Min Max Units NEND(5) Endurance MIL-STD-883, Test Method 1033 1,000,000 TDR(5) Data Retention MIL-STD-883, Test Method 1008 100 Years VZAP(5) ESD Susceptibility MIL-STD-883, Test Method 3015 2000 Volts ILTH(5)(7) Latch-Up JEDEC Standard 17 100 mA Cycles/Byte Notes: 1. Test Conditions according to "AC Test Conditions" table. 2. Power-up, Input Reference Voltage VCC = VTH, Reset Output Reference Voltage and Load according to "AC Test Conditions" Table 3. Power-Down, Input Reference Voltage VCC = VTH, Reset Output Reference Voltage and Load according to "AC Test Conditions" Table 4. VCC Glitch Reference Voltage = VTHmin; Based on characterization data 5. This parameter is characterized initially and after a design or process change that affects the parameter. Not 100% tested. 6. tPUR and tPUW are the delays required from the time VCC is stable until the specified memory operation can be initiated. 7. Latch-up protection is provided for stresses up to 100mA on input and output pins from -1V to VCC + 1V. Doc. No. 3008, Rev. I 6 Preliminary Information CAT1024, CAT1025 DEVICE OPERATION Reset Controller Description The CAT1024/25 precision RESET controllers ensure correct system operation during brownout and power up/down conditions. They are configured with open drain RESET outputs. including write operations. If the Reset output(s) are active, in progress communications to the EEPROM are aborted and no new communications are allowed. In this condition an internal write cycle to the memory can not be started, but an in progress internal non-volatile memory write cycle can not be aborted. An internal write cycle initiated before the Reset condition can be successfully finished if there is enough time (5ms) before VCC reaches the minimum value of 2V. During power-up, the RESET outputs remain active until VCC reaches the VTH threshold and will continue driving the outputs for approximately 200ms (tPURST) after reaching VTH. After the tPURST timeout interval, the device will cease to drive the reset outputs. At this point the reset outputs will be pulled up or down by their respective pull up/down resistors. In addition, the CAT1025 includes a Write Protection Input which when tied to VCC will disable any write operations to the device. During power-down, the RESET outputs will be active when VCC falls below VTH. The RESET output will be valid so long as VCC is >1.0V (VRVALID). The device is designed to ignore the fast negative going VCC transient pulses (glitches). Reset output timing is shown in Figure 1. Manual Reset Operation The RESET pin can operate as reset output and manual reset input. The input is edge triggered; that is, the RESET input will initiate a reset timeout after detecting a high to low transition. When RESET I/O is driven to the active state, the 200 msec timer will begin to time the reset interval. If external reset is shorter than 200 ms, Reset outputs will remain active at least 200 ms. CAT1024/25 also have a separate manual reset input. Driving the MR input low by connecting a pushbutton (normally open) from MR pin to GND will generate a reset condition. The input has a internal pull up resistor. Reset remains asserted while MR is low and for the Reset Timeout period after MR input has gone high. Glitches shorter than 100 ns on MR input will not generate a reset pulse. No external debouncing circuits are required. Manual reset operation using MR input is shown in Figure 2. Hardware Data Protection The CAT1024/25 family has been designed to solve many of the data corruption issues that have long been associated with serial EEPROMs. Data corruption occurs when incorrect data is stored in a memory location which is assumed to hold correct data. Whenever the device is in a Reset condition, the embedded EEPROM is disabled for all operations, 7 Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information t Figure 1. RESET Output Timing GLITCH VTH VRVALID t PURST VCC t RPD t PURST RESET RESET Figure 2. MR Operation and Timing t MRW MR t MRD t PURST RESET RESET Doc. No. 3008, Rev. I 8 t RPD Preliminary Information CAT1024, CAT1025 EMBEDDED EEPROM OPERATION SDA when SCL is HIGH. The CAT1024/25 monitors the SDA and SCL lines and will not respond until this condition is met. The CAT1024 and CAT1025 feature a 2kbit embedded serial EEPROM that supports the I 2C Bus data transmission protocol. This Inter-Integrated Circuit Bus protocol defines any device that sends data to the bus to be a transmitter and any device receiving data to be a receiver. The transfer is controlled by the Master device which generates the serial clock and all START and STOP conditions for bus access. Both the Master device and Slave device can operate as either transmitter or receiver, but the Master device controls which mode is activated. STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. DEVICE ADDRESSING The Master begins a transmission by sending a START condition. The Master sends the address of the particular slave device it is requesting. The four most significant bits of the 8-bit slave address are programmable in metal and the default is 1010. I2C Bus Protocol The features of the I2C bus protocol are defined as follows: (1) Data transfer may be initiated only when the bus is not busy. The last bit of the slave address specifies whether a Read or Write operation is to be performed. When this bit is set to 1, a Read operation is selected, and when set to 0, a Write operation is selected. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock line is high will be interpreted as a START or STOP condition. After the Master sends a START condition and the slave address byte, the CAT1024/25 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The CAT1024/25 then performs a Read or Write operation depending on the R/W bit. START Condition The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of Figure 3. Bus Timing tF tHIGH tLOW tR tLOW SCL tSU:STA tHD:STA tHD:DAT tSU:DAT tSU:STO SDA IN tAA tBUF tDH SDA OUT Figure 4. Write Cycle Timing SCL SDA 8TH BIT BYTE n ACK tWR STOP CONDITION 9 START CONDITION ADDRESS Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information ACKNOWLEDGE WRITE OPERATIONS After a successful data transfer, each receiving device is required to generate an acknowledge. The acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. Byte Write In the Byte Write mode, the Master device sends the START condition and the slave address information (with the R/W bit set to zero) to the Slave device. After the Slave generates an acknowledge, the Master sends a 8-bit address that is to be written into the address pointers of the device. After receiving another acknowledge from the Slave, the Master device transmits the data to be written into the addressed memory location. The CAT1024/25 acknowledges once more and the Master generates the STOP condition. At this time, the device begins an internal programming cycle to non-volatile memory. While the cycle is in progress, the device will not respond to any request from the Master device. The CAT1024/25 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8bit byte. When the CAT1024/25 begins a READ mode it transmits 8 bits of data, releases the SDA line and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT1024/25 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. Figure 5. Start/Stop Timing SDA SCL START BIT STOP BIT Figure 6. Acknowledge Timing SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER ACKNOWLEDGE START Figure 7. Slave Address Bits Default Configuration CAT Doc. No. 3008, Rev. I 1 0 1 0 0 0 10 0 R/W Preliminary Information CAT1024, CAT1025 Page Write The CAT1024/25 writes up to 16 bytes of data in a single write cycle, using the Page Write operation. The page write operation is initiated in the same manner as the byte write operation, however instead of terminating after the initial byte is transmitted, the Master is allowed to send up to 15 additional bytes. After each byte has been transmitted, the CAT1024/25 will respond with an acknowledge and internally increment the lower order address bits by one. The high order bits remain unchanged. If the Master transmits more than 16 bytes before sending the STOP condition, the address counter `wraps around,' and previously transmitted data will be overwritten. When all 16 bytes are received, and the STOP condition has been sent by the Master, the internal programming cycle begins. At this point, all received data is written to the CAT1024/25 in a single write cycle. Figure 8. Byte Write Timing BUS ACTIVITY: MASTER SDA LINE S T A R T SLAVE ADDRESS BYTE ADDRESS S T O P DATA P S A C K A C K A C K Figure 9. Page Write Timing BUS ACTIVITY: MASTER SDA LINE S T A R T SLAVE ADDRESS BYTE ADDRESS (n) DATA n S T DATA n+15 O P DATA n+1 S P A C K A C K A C K 11 A C K A C K Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information Acknowledge Polling memory array is protected and becomes read only. The CAT1025 will accept both slave and byte addresses, but the memory location accessed is protected from programming by the device's failure to send an acknowledge after the first byte of data is received. Disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host's write opration, the CAT1024/25 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address for a write operation. If the device is still busy with the write operation, no ACK will be returned. If a write operation has completed, an ACK will be returned and the host can then proceed with the next read or write operation. Read Operations The READ operation for the CAT1024/25 is initiated in the same manner as the write operation with one exception, that R/W bit is set to one. Three different READ operations are possible: Immediate/Current Address READ, Selective/Random READ and Sequential READ. WRITE PROTECTION The Write Protection feature (CAT1025 only) allows the user to protect against inadvertent memory array programming. If the WP pin is tied to VCC, the entire Figure 10. Immediate Address Read Timing BUS ACTIVITY: MASTER SDA LINE S T A R T S T O P SLAVE ADDRESS S P A C K DATA N O A C K SCL SDA 8 9 8TH BIT DATA OUT Doc. No. 3008, Rev. I NO ACK 12 STOP Preliminary Information CAT1024, CAT1025 Immediate/Current Address Read Sequential Read The CAT1024 and CAT1025 address counter contains the address of the last byte accessed, incremented by one. In other words, if the last READ or WRITE access was to address N, the READ immediately following would access data from address N+1. For N=E=255, the counter will wrap around to zero and continue to clock out valid data. After the CAT1024 and CAT1025 receives its slave address information (with the R/W bit set to one), it issues an acknowledge, then transmits the 8-bit byte requested. The master device does not send an acknowledge, but will generate a STOP condition. The Sequential READ operation can be initiated by either the Immediate Address READ or Selective READ operations. After the CAT1024 and CAT1025 sends the inital 8-bit byte requested, the Master will responds with an acknowledge which tells the device it requires more data. The CAT1024 and CAT1025 will continue to output an 8-bit byte for each acknowledge, thus sending the STOP condition. The data being transmitted from the CAT1024 and CAT1025 is sent sequentially with the data from address N followed by data from address N+1. The READ operation address counter increments all of the CAT1024 and CAT1025 address bits so that the entire memory array can be read during one operation. Selective/Random Read Selective/Random READ operations allow the Master device to select at random any memory location for a READ operation. The Master device first performs a `dummy' write operation by sending the START condition, slave address and byte addresses of the location it wishes to read. After the CAT1024 and CAT1025 acknowledges, the Master device sends the START condition and the slave address again, this time with the R/W bit set to one. The CAT1024 and CAT1025 then responds with its acknowledge and sends the 8-bit byte requested. The master device does not send an acknowledge but will generate a STOP condition. Figure 11. Selective Read Timing BUS ACTIVITY: MASTER SDA LINE S T A R T SLAVE ADDRESS S T A R T BYTE ADDRESS (n) S T O P SLAVE ADDRESS S S A C K P A C K A C K DATA n N O A C K Figure 12. Sequential Read Timing BUS ACTIVITY: MASTER SLAVE ADDRESS DATA n DATA n+1 DATA n+2 S T O P DATA n+x SDA LINE P A C K A C K A C K A C K N O A C K 13 Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information PACKAGE OUTLINES TDFN 3X4.9 PACKAGE (RD2) A 5 8 5 B 4.90 + 0.10 (5) 3.00 + 0.15 8 0.10 0.15 0.20 0.25 2.00 + 0.15 0.60 + 0.10 (8X) PIN 1 ID 2x d 0.15 c 1 PIN 1 INDEX AREA 3.00 + 0.10 (S) 4 4 2x d 0.15 c 0.30 + 0.05 (8X) 8x j 0.10m C A B 1 0.65 TYP. (6x) 1.95 REF. (2x) 0.75 + 0.05 f 0.10 c 0.20 REF. 8x d 0.08 c C NOTE: 1. ALL DIMENSION ARE IN mm. ANGLES IN DEGREES. 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. COPLANARITY SHALL NOT EXCEED 0.08mm. 3. WARPAGE SHALL NOT EXCEED 0.10mm. 4. PACKAGE LENGTH / PACKAGE WIDTH ARE CONSIDERED AS SPECIAL CHARACTERISTIC(S). 5. REFER TO JEDEC MO-229, FOOTPRINTS ARE COMPATIBLE TO 8 MSOP. 0.0-0.05 Doc. No. 3008, Rev. I 14 Preliminary Information CAT1024, CAT1025 TDFN 3X3 PACKAGE (RD4) 5 0.75 + 0.05 A B 3.00 + 0.10 (S) 8 2X 0.15 C 1 4 3.00 + 0.10 (S) 2X 0.0 - 0.05 0.15 C PIN 1 INDEX AREA 5 8 1.50 + 0.10 0.75 + 0.05 C 2.30 + 0.10 C0.35 0.25 min. PIN 1 ID 1 0.30 + 0.07 (8x) 0.30 + 0.10 (8x) 0.65 TYP. (6x) 1.95 REF. (2x) NOTE: 1. ALL DIMENSION ARE IN mm. ANGLES IN DEGREES. 2. COPLANARITY SHALL NOT EXCEED 0.08 mm. 3. WARPAGE SHALL NOT EXCEED 0.10 mm. 4. PACKAGE LENGTH / PACKAGE WIDTH ARE CONSIDERED AS SPECIAL CHARACTERISTIC(S) 5. REFER JEDEC MO-229 / WEEC 15 Doc No. 3008, Rev. I CAT1024, CAT1025 Preliminary Information Ordering Information Prefix CAT Optional Company ID Device # Suffix 1024 Product Number 1024: 2K 1025: 2K S I Temperature Range I = Industrial (-40C to 85C) E = Extended Automotive (-40C to +125C) Package P: PDIP S: SOIC (JEDEC) R: MSOP U: TSSOP RD2: 8-pad TDFN (3x4.9mm, MSOP Footprint) RD4: 8-pad TDFN (3x3mm) L: PDIP (Lead free, Halogen free) V: SOIC (JEDEC, Lead free, Halogen free) Z: MSOP Lead free, Halogen free) Y: TSSOP (Lead free, Halogen free) ZD2: 3x4.9mm TDFN (Lead free, Halogen free) ZD4: 3x3mm TDFN (Lead free, Halogen free) -30 TE13 Tape & Reel TE13: 2000/Reel Reset Threshold Voltage 45: 4.5-4.75V 42: 4.25-4.5V 30: 3.0-3.15V 28: 2.85-3.0V 25: 2.55-2.7V Note: (1) The device used in the above example is a CAT1024SI-30TE13 (Supervisory circuit with I2C serial 2k CMOS EEPROM, SOIC, Industrial Temperature, 3.0-3.15V Reset Threshold Voltage, Tape and Reel). Doc. No. 3008, Rev. I 16 REVISION HISTORY Date Rev. Reason 11/7/03 I Eliminated Automotive temperature range Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP TM AE2 TM 2 I C is a trademark of Philips Corporation Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company's corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION and SPECIFICALLY DISCLAIMS ANY and ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.catalyst-semiconductor.com Publication #: Revison: Issue date: Type: 3008 I 11/10/03 Preliminary