General Description
The MAX13051 ±80V fault-protected CAN transceiver
with autobaud is ideal for device net and other industri-
al network applications where overvoltage protection is
required. The MAX13051 provides a link between the
CAN protocol controller and the physical wires of the
bus lines in a control area network (CAN).
The MAX13051 features three different modes of opera-
tion: high speed, slope control, and standby. High-
speed mode allows data rates up to 1Mbps. The
slope-control mode can be used to program the slew
rate of the transmitter for data rates of up to 500kbps,
reducing the effects of EMI and allowing the use of
unshielded-twisted or parallel cable. In standby mode,
the transmitter shuts off and a low-power receiver moni-
tors the bus, waiting for a wake-up signal.
The MAX13051 provides a transmitter data (TXD) domi-
nant timeout function that prevents erroneous CAN con-
trollers from clamping the bus to a dominant level if the
TXD input is held low for greater than 1ms. The
MAX13051 also provides an autobaud feature allowing
the microcontroller to compute the incoming baud rate
without destroying CAN protocol communication. The
MAX13051 input common-mode range is greater than
±12V, exceeding the ISO 11898 specification of -2V to
+7V, and features ±6kV Human Body Model protection,
making these devices ideal for harsh environments. The
MAX13051 is available in an 8-pin SO package and is
specified from the -40°C to +85°C and -40°C to +125°C
temperature ranges.
Applications
Industrial Networks
Device Net Nodes
Telecom
HVAC
Features
♦Fully Compatible with the ISO 11898 Standard
♦Autobaud Mode
♦Short-Circuit Protection
♦High-Speed Operation Up to 1Mbps
♦Slope-Control Mode
♦Low-Current Standby Mode
♦Thermal Shutdown
♦Transmit Data Dominant Timeout
♦±6kV Human Body Model ESD Protection
♦Greater than ±12V Common-Mode Range
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
________________________________________________________________ Maxim Integrated Products 1
19-3500; Rev 0; 11/04
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
CANL
AUTOBAUDRXD
1
2
8
7
RS
CANHGND
VCC
TXD
SO
TOP VIEW
3
4
6
5
MAX13051
Pin Configuration
MAX13051
120Ω
120Ω
CAN
CONTROLLER
VCC
0.1µF
GND GND
TX0
RX0
I/O
I/O
CANL
CANH
RS
AUTOBAUD
RXD
TXD
VCC
16kΩ TO 200kΩ
Typical Operating Circuit
Ordering Information
PART TEMP RANGE PIN-PACKAGE
MAX13051ESA -40°C to +85°C 8 SO
MAX13051ASA -40°C to +125°C 8 SO
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(All voltages referenced to GND.)
VCC .......................................................................................-0.3V to +6V
RS...............................................................-0.3V to (VCC + 0.3V)
TXD, RXD, AUTOBAUD............................................-0.3V to +6V
CANH, CANL .......................................................................±80V
Continuous Power Dissipation (TA= +70°C)
8-Pin SO (derate 5.9mW/°C above +70°C) .................470mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
DC ELECTRICAL CHARACTERISTICS
(VCC = +5V ±5%, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +5V, TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Dominant, RL = 60Ω72
Supply Current ICC Recessive 15 mA
Standby Current ISTANDBY 25 µA
Thermal-Shutdown Threshold VTSH +165 °C
Thermal-Shutdown Hysteresis 13 °C
INPUT LEVELS (TXD, AUTOBAUD)
High-Level Input Voltage VIH 2V
Low-Level Input Voltage VIL 0.8 V
VTXD = VCC -5 +5
High-Level Input Current IIH VAUTOBAUD = VCC +5 +15 µA
VTXD = GND -300 -100
Low-Level Input Current IIL VAUTOBAUD = GND -5 +5 µA
Input Capacitance CIN 10 pF
CANH, CANL TRANSMITTER
Normal mode, VTXD = VCC, no load 2 3 V
Recessive Bus Voltage VCANH,
VCANL Standby mode, no load -100 +100 mV
-76V < VCANH, VCANL < +76V ±3
Recessive Output Current ICANH,
ICANL -32V < VCANH, VCANL < +32V -2.5 +2.5 mA
CANH Output Voltage VCANH VTXD = 0, dominant 3.0 4.5 V
CANL Output Voltage VCANL VTXD = 0, dominant 0.50 1.75 V
Matching Between CANH and CANL
Output Voltage ∆DOM VTXD = 0, dominant, TA = +25°C
(VCANH + VCANL) -VCC -100 +150 mV
Dominant, VTXD = 0, 45Ω < RL < 60Ω1.5 3.0 V
Differential Output
(VCANH - VCANL)VDIFF Recessive, VTXD = VCC, no load -50 +50 mV
CANH Short-Circuit Current ICANHSC VCANH = 0, VTXD = 0 -100 -70 -45 mA
VCANL = 5V, VTXD = 0 40 60 90
VCANL = 40V, VTXD = 0 40 60 90CANL Short-Circuit Current ICANLSC
VCANL = 76V, VTXD = 0 63
mA
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
_______________________________________________________________________________________ 3
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +5V ±5%, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +5V, TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
RXD OUTPUT LEVELS
RXD High Output Voltage Level VOH I = -100µA 0.8 x VCC VCC V
RXD Low Output Voltage Level VOL I = 5mA 0.4 V
DC BUS RECEIVER (VTXD = VCC, CANH and CANL externally driven)
-12V < VCM < +12V 0.5 0.7 0.9
Differential Input Voltage VDIFF -12V < VCM < +12V, standby mode 0.5 1.1 V
Differential Input Hysteresis VDIFF
(
HYST
)
Normal mode, -12V < VCM < +12V 70 mV
Common-Mode Input Resistance RICM Normal or standby mode,
VCANH = VCANL = ±12V 15 35 kΩ
Matching Between CANH and CANL
Common-Mode Input Resistance RIC_MATCH -3 +3 %
Differential Input Resistance RDIFF Normal or standby mode,
VCANH - VCANL = 1V 25 75 kΩ
Common-Mode Input Capacitance VTXD = VCC 20 pF
Differential Input Capacitance VTXD = VCC 10 pF
Input Leakage Current ILI VCC = 0, VCANH = VCANL = 5V -5 +5 µA
SLOPE CONTROL (RS )
Input Voltage for High-Speed Mode VIL_RS 0.3 x VCC V
Input Voltage for Standby VIH_RS 0.75 x VCC V
Slope-Control Mode Voltage VSLOPE -200µA < IRS < 10µA 0.4 x VCC 0.6 x VCC V
High-Speed Mode Current IIL_RS VRS = 0 -500 µA
TIMING CHARACTERISTICS
(VCC = +5V ±5%, RL= 60Ω, CL= 100pF, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +5V and TA= +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Delay TXD to Bus Active tONTXD VRS = 0 (Figure 1) 66 110 ns
Delay TXD to Bus Inactive tOFFTXD VRS = 0 (Figure 1) 61 95 ns
Delay Bus to Receiver Active tONRXD VRS = 0 (Figure 1) 54 115 ns
Delay Bus to Receiver Inactive tOFFRXD VRS = 0 (Figure 1) 46 160 ns
Delay TXD to RXD Active tONLOOP VRS = 0 (Figure 1) 121 255 ns
Delay TXD to RXD Inactive TOFFLOOP VRS = 0 (Figure 1) 108 255 ns
RRS = 24kΩ (500kbps) 280 450 ns
RRS = 100kΩ (125kbps) 0.82 1.6
Delay TXD to RXD Active (Dominant
Loop Delay) Slew-Rate Controlled tONLOOP_S
RRS = 180kΩ (62.5kbps) 1.37 5 µs
RRS = 24kΩ (500kbps) 386 600 ns
RRS = 100kΩ (125kbps) 0.74 1.6
Delay TXD to RXD Inactive (Loop
Delay) Slew-Rate Controlled tOFFLOOP_S
RRS = 180kΩ (62.5kbps) 0.97 5 µs
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
4 _______________________________________________________________________________________
Note 1: All currents into device are positive and all currents out of the device are negative. All voltages are referenced to device
ground unless otherwise noted.
TIMING CHARACTERISTICS (continued)
(VCC = +5V ±5%, RL= 60Ω, CL= 100pF, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +5V and TA= +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
RRS = 24kΩ (500kbps) 10
RRS = 100kΩ (125kbps) 2.7
Differential-Output Slew Rate |SR|
RRS = 180kΩ (62.5kbps) 1.6
V/µs
Dominant Time for Wake-Up Through
Bus (Figure 2) tWAKE Standby mode, VDIFF = 3V 0.75 1.5 3.00 µs
TXD Dominant Timeout tDOM VTXD = 0 0.3 0.6 1.0 ms
ESD Protection Human Body Model (CANH, CANL) 6 kV
0.9V
0.3 x VCC
0.7 x VCC
0.5V
tONTXD
tONRXD
tONLOOP
tOFFTXD
tOFFRXD
tOFFLOOP
RECESSIVE
DOMINANT
TXD
VDIFF
RXD
Figure 1. Timing Diagram
Timing Diagrams
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
_______________________________________________________________________________________ 5
tWAKE
0.9V
VDIFF
RXD
STANDBY MODE
DOMINANT
Figure 2. Timing Diagram for Standby and Wake-Up Signal
Timing Diagrams (continued)
Typical Operating Characteristics
(VCC = +5V, RL= 60Ω, CL= 100pF, TA= +25°C, unless otherwise specified.)
SLEW RATE
vs. RRS AT 100kbps
MAX13051 toc01
RRS (kΩ)
SLEW RATE (V/µs)
18016014012010080604020
5
10
15
20
25
30
0
0 200
RECESSIVE
DOMINANT
SUPPLY CURRENT
vs. DATA RATE
MAX13051 toc02
DATA RATE (kbps)
SUPPLY CURRENT (mA)
900800700600500400300200100
20
25
30
35
40
15
0 1000
TA = +25°CTA = -40°C
TA = +125°C
STANDBY SUPPLY CURRENT
vs. TEMPERATURE (RS = VCC)
MAX13051 toc03
TEMPERATURE (°C)
STANDBY SUPPLY CURRENT (µA)
603510-15
11
12
13
14
15
16
17
18
19
20
10
-40 85
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
6 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(VCC = +5V, RL= 60Ω, CL= 100pF, TA= +25°C, unless otherwise specified.)
RECEIVER PROPAGATION DELAY
vs. TEMPERATURE
MAX13051 toc04
TEMPERATURE (°C)
RECEIVER PROPAGATION DELAY (ns)
1007525 500-25
10
20
30
40
50
60
70
80
90
100
0
-50 125
RECESSIVE
RRS = GND, DATA RATE = 100kbps
DOMINANT
DRIVER PROPAGATION DELAY
vs. TEMPERATURE
MAX13051 toc05
TEMPERATURE (°C)
DRIVER PROPAGATION DELAY (ns)
603510-15
20
40
60
80
100
120
140
160
180
200
0
-40 85
RECESSIVE
DOMINANT
RRS = GND, DATA RATE = 100kbps
RECEIVER OUTPUT LOW
vs. OUTPUT CURRENT
MAX13051 toc06
OUTPUT CURRENT (mA)
VOLTAGE RXD (V)
2015105
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0
0
TA = -40°C
TA = +125°C
TA = +25°C
RECEIVER OUTPUT HIGH
vs. OUTPUT CURRENT
MAX13051 toc07
OUTPUT CURRENT (mA)
RECEIVER OUTPUT HIGH (VCC - RXD) (V)
764 52 31
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0
08
TA = -40°C
TA = +125°C
TA = +25°C
DIFFERENTIAL VOLTAGE
vs. DIFFERENTIAL LOAD
MAX13051 toc08
DIFFERENTIAL LOAD RL (Ω)
DIFFERENTIAL VOLTAGE (V)
26022018014010060
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
20 300
TA = +125°C
TA = -40°C
TA = +25°C
RECEIVER PROPAGATION DELAY
MAX13051 toc09
200ns
VDIFF
(1V/div)
RXD
(2V/div)
DRIVER PROPAGATION DELAY,
(with RRS = 24kΩ, 75kΩ AND 100kΩ)
MAX13051 toc10
1.00µs
TXD
(5V/div)
VDIFF
(2V/div)
RRS = 24kΩ
VDIFF
(2V/div)
RRS = 75kΩ
VDIFF
(2V/div)
RRS = 100kΩ
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
_______________________________________________________________________________________ 7
Typical Operating Characteristics (continued)
(VCC = +5V, RL= 60Ω, CL= 100pF, TA= +25°C, unless otherwise specified.)
DRIVER PROPAGATION DELAY,
(RRS = GND)
MAX13051 toc11
200ns/div
TXD
(2V/div)
VDIFF
(1V/div)
LOOPBACK PROPAGATION DELAY
vs. RRS
MAX13051 toc12
RRS (kΩ)
LOOPBACK PROPAGATION DELAY (µs)
18016014012010080604020
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0
0200
RECESSIVE
DOMINANT
Receive Data Output. RXD is a CMOS/TTL-compatible output from the physical bus lines CANH and CANL.
AUTOBAUD
Pin Description
MAX13051
Detail Description
±80V Fault Tolerant
The MAX13051 features ±80V fault protection. This
extended voltage range of CANH and CANL allows
communication in high-voltage systems up to 80V.
Operating Modes
High-Speed Mode
The MAX13051 can achieve transmission rates of up to
1Mbps when operating in high-speed mode. To oper-
ate in high-speed mode, short RS to ground.
Slope-Control Mode
Connect a resistor from RS to ground to select slope-
control mode (Table 1). In slope-control mode, CANH
and CANL slew rates are controlled by the resistor,
(16kΩ≤RRS ≤200kΩ), connected between RS and
GND. Controlling the rise and fall slopes reduces high-
frequency EMI and allows the use of an unshielded-
twisted pair or a parallel pair of wires as bus lines. The
slew rate can be approximated using the formula
below:
where, SR is the desired slew rate and RRS is in kΩ.
Standby Mode
In standby mode (RS = high), the transmitter is
switched off and the receiver is switched to a low-cur-
rent/low-speed state. The supply current reduces to
15µA to detect and recognize a wake-up event on the
bus line. During standby mode, the bus line is moni-
tored with a low-differential comparator. Once the com-
parator detects a dominant bus level greater than
tWAKE, RXD pulls low.
Autobaud Mode
The MAX13051 logic-controlled autobaud input allows
a microcontroller to compute the incoming baud rate
without destroying CAN protocol communication. When
operating in autobaud mode, TXD is looped back to
RXD without applying a differential signal at CANH and
CANL. See Figure 4.
SR V s RRS
/µ
()
≈250
±80V Fault-Protected Can Transceiver
with Autobaud
8 _______________________________________________________________________________________
DRIVER
THERMAL
SHUTDOWN
TIMEOUT
AND SLOPE-
CONTROL
MODE
WAKE-UP MODE
CONTROL
WAKE-UP
FILTER
MUX
AUTOBAUD
CIRCUITRY
VCC
MAX13051
VCC
CANH
CANL
RS
TXD
RXD
AUTOBAUD
ENABLE
GND
Figure 3. MAX13051 Functional Diagram
Transmitter
The transmitter converts a single-ended input (TXD)
from the CAN controller to differential outputs for the
bus lines (CANH, CANL). The truth table for the trans-
mitter and receiver is given in Table 2.
TXD Dominant Timeout
The MAX13051 provides a transmitter-dominant timeout
that prevents erroneous CAN controllers from clamping
the bus to a dominant level by maintaining a continuous
low TXD signal. When the TXD remains in the dominant
state for greater than 1ms (max), the transmitter
becomes disabled, driving the bus line to a recessive
state (Figure 5). After a dominant timeout fault, the
MAX13051’s transmitter becomes enabled upon
detecting a rising edge at TXD.
Receiver
The receiver reads differential inputs from the bus lines
(CANH, CANL) and transfers this data as a single-
ended output (RXD) to the CAN controller. It consists of
a comparator that senses the difference, VDIFF =
(CANH - CANL), with respect to an internal threshold of
0.7V. If this difference is positive, (VDIFF > 0.9V), a
logic-low is present at RXD. If negative, (VDIFF < 0.5V),
a logic-high is present. The receiver always echoes the
CAN bus data when not operating in autobaud mode.
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
_______________________________________________________________________________________ 9
Table 1. Mode Selection Truth Table
CONDITION FORCED AT PIN RS MODE RESULTING CURRENT AT RS
VRS ≤ 0.3V x VCC High Speed 200µA ≤ |IRS| ≤ 500µA
0.4V x VCC < VRS ≤ 0.6V x VCC Slope Control 10µA ≤ |IRS| ≤ 200µA
VRS ≥ 0.75V x VCC Standby |IRS| ≤ 10µA
TXD
RXD
CANH - CANL
TXD
RXD
AUTOBAUD
TRANSMITTER
INPUT
RECEIVER
OUTPUT
Figure 4. MAX13051 Autobaud Timing Diagram
Table 2. Transmitter and Receiver Truth Table when Not Connected to the Bus
TXD RS CANH CANL BUS STATE RXD
Low VRS ≤ 0.75V x VCC High Low Dominant Low
High or Float VRS ≤ 0.75V x VCC VCC / 2 VCC / 2 Recessive High
XV
RS ≥ 0.75V x VCC RICM GND RICM GND Recessive High
*Common-mode input resistance.
MAX13051
The CANH and CANL common-mode range is ±12V
exceeding the ISO 11898 specification at -2V to +7V.
RXD is logic-high when CANH and CANL are shorted
or undriven.
Driver Output Protection
The MAX13051 current-limiting feature protects the
transmitter output stage against a short circuit to a posi-
tive and negative battery voltage. Although the power
dissipation increases during this fault condition, current-
limit protection prevents destruction of the transmitter
output stage. Upon removal of a short, the MAX13051
resumes normal operation.
Thermal Shutdown
If the junction temperature exceeds +165°C, the device
is switched off. The hysteresis is approximately 13°C,
disabling thermal shutdown once the temperature
drops below 152°C. In thermal shutdown, CANH and
CANL go recessive. After a thermal-shutdown event,
the MAX13051 resumes normal operation when the
junction temperature drops below the thermal-shut-
down hysteresis, and upon the MAX13051 detecting a
rising edge at TXD.
Applications Information
Reduced EMI and Reflections
In slope-control mode, the CANH and CANL outputs
are slew-rate limited, minimizing high-frequency EMI,
and reducing reflections caused by improperly termi-
nated cables.
In multidrop CAN applications, it is important to main-
tain a direct point-to-point wiring scheme. A single pair
of wires should connect each element of the CAN bus,
and the two ends of the bus should be terminated with
120Ωresistors, see Figure 6. A star configuration
should never be used.
Any deviation from the point-to-point wiring scheme
creates a stub. The high-speed edge of the CAN data
on a stub can create reflections back down the bus.
These reflections can cause data errors by eroding the
noise margin of the system.
Although stubs are unavoidable in a multidrop system,
care should be taken to keep these stubs as small as
possible, especially in high-speed mode. In slope-con-
trol mode, the requirements are not as rigorous, but
stub length should still be minimized.
Layout Consideration
CANH and CANL are differential signals and steps
should be taken to insure equivalent parasitic capaci-
tance. Place the resistor at RS as close as possible to
the MAX13051 to minimize any possible noise coupling
at the input.
±80V Fault-Protected Can Transceiver
with Autobaud
10 ______________________________________________________________________________________
TRANSMITTER
DISABLED
TRANSMITTER
ENABLED
tDOM
TXD
VCANH - VCANL
Figure 5. Transmitter-Dominant Timeout Timing Diagram
MAX13051
RXD
RL = 120ΩRL = 120Ω
TRANSCEIVER 2
TRANSCEIVER 1
TRANSCEIVER 3
CANH
CANL
TXD
STUB LENGTH
KEEP AS SHORT AS POSSIBLE
TWISTED PAIR
Figure 6. Multiple Receivers Connected to CAN Bus
Power Supply and Bypassing
The MAX13051 requires no special layout considera-
tions beyond common practices. Bypass VCC to GND
with a 0.1µF ceramic capacitor mounted closely to the
IC with short lead lengths and wide trace widths.
±6kV ESD Protection
ESD protection structures are incorporated on all inputs
to protect against ESD encountered during handling and
assembly. CANH and CANL inputs have extra protection
to protect against static electricity found in normal opera-
tion. Maxim’s engineers have developed state-of-the-art
structures to protect these pins (CANH, CANL) against
±6kV ESD without damage. ESD protection can be test-
ed in several ways. The CANH and CANL inputs are
characterized for protection to ±6kV using the Human
Body Model.
ESD Test Conditions
ESD performance depends on a number of conditions.
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Human Body Model
Figure 7 shows the Human Body Model, and Figure 8
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the device through a
1.5kΩresistor.
Chip Information
TRANSISTOR COUNT: 1400
PROCESS: BiCMOS
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
______________________________________________________________________________________ 11
CHARGE-CURRENT-
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
RC
1MΩ
RD
1.5kΩ
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 7. Human Body ESD Test Model
IP 100%
90%
36.8%
tRL TIME
tDL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
0
AMPERES
Figure 8. Human Body Model Current Waveform
MAX13051
±80V Fault-Protected Can Transceiver
with Autobaud
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
SOICN .EPS
PACKAGE OUTLINE, .150" SOIC
1
1
21-0041 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.010
0.069
0.019
0.157
0.010
INCHES
0.150
0.007
E
C
DIM
0.014
0.004
B
A1
MIN
0.053A
0.19
3.80 4.00
0.25
MILLIMETERS
0.10
0.35
1.35
MIN
0.49
0.25
MAX
1.75
0.050
0.016L0.40 1.27
0.3940.386D
D
MINDIM
D
INCHES
MAX
9.80 10.00
MILLIMETERS
MIN MAX
16 AC
0.337 0.344 AB8.758.55 14
0.189 0.197 AA5.004.80 8
N MS012
N
SIDE VIEW
H 0.2440.228 5.80 6.20
e 0.050 BSC 1.27 BSC
C
HE
eBA1
A
D
0∞-8∞
L
1
VARIATIONS: