PC745BMZFU300LE - Atmel Corporation

Features

• 18.1SPECint95, Estimates 12.3 SPECfp95 at 400 MHz (PC755B)

• 15.7SPECint95, 9SPECfp95 at 350 MHz (PC745B)

• 733 MIPS at 400 MHz (PC755B) at 641 MIPS at 350 MHz (PC745B)

• Selectable Bus Clock (12 CPU Bus Dividers up to 10x)

• PDTypical 6.4W at 400 MHz, Full Operating Conditions.

• Nap, Doze and Sleep Modes for Power Savings

• Superscalar (3 Instructions per Clock Cycle) Two Instruction + Branch

• 4 Beta Byte Virtual Memory, 4-GByte of Physical Memory

• 64-bit Data and 32-bit Address Bus Interface

• 32-KB Instruction and Data Cache

• Six Independent Execution Units

• Write-back and Write-through Operations

• fINT max=400MHz(TBC)

• fBUS max = 100 MHz

• Voltage I/O 2.5V/3.3V; Voltage Int 2.0V

Description

The PC755B and PC745B PowerPC®microprocessors are high-performance, low-

power, 32-bit implementations of the PowerPC Reduced Instruction Set Computer

(RISC) architecture, especially enhanced for embedded applications.

The PC755B and PC745B microprocessors differ only in that the PC755B features an

enhanced, dedicated L2 cache interface with on-chip L2 tags. The PC755B is a drop-

in replacement for the award winning PowerPC 750™ microprocessor and is footprint

and user software code compatible with the MPC7400 microprocessor with AltiVec™

technology. The PC745B is a drop-in replacement for the PowerPC 740™micropro-

cessor and is also footprint and user software code compatible with the PowerPC

603e™microprocessor. PC755B/745B microprocessors provide on-chip debug sup-

port and are fully JTAG-compliant.

The PC745B microprocessor is pin compatible with the TSPC603e family.

Screening

This product is manufactured in full compliance with:

• CBGA + CI-CGA + FC-PBGA up screenings based upon Atmel standards

• Full military temperature range (Tj = -55°C,+125°C)

industrial temperature range (Tj = -40°C,+110°C)

ZF suffix

PBGA255

Flip-Chip Plastic Ball Grid Array

ZF suffix

PBGA360

Flip-Chip Plastic Ball Grid Array

G suffix

CBGA255 and CBGA360

Ceramic Ball Grid Array

GS suffix

CI-CBGA255 and CI-CBGA360

Ceramic Ball Grid Array

with Solder Column Interposer (SCI)

PowerPC

755B/745B RISC

Microprocessor

PC755B/745B

Preliminary

β-site

Rev. 2138A–HIREL–05/02

2PC755B/745B 2138A–HIREL–05/02

General Description

Simplified Block Diagram The PC755B is targeted for low power systems and supports power management fea-

tures such as doze, nap, sleep, and dynamic power management. The PC755B

consists of a processor core and an internal L2 Tag combined with a dedicated L2

cache interface and a 60x bus.

Figure 1. PC755B Block Diagram

Additional Features

¥ Time Base Counter/Decrementer

¥ Clock Multiplier

¥ JTAG/COP Interface

¥ Thermal/Power Management

¥ Performance Monitor

Fetcher Branch Processing

BTIC

64-Entry

+ x ÖFPSCR

CR FPSCR

L2CR

CTR

BHT

Data MMU

Instruction MMU

Not in the PC745

+ x Ö

Instruction Unit

Unit

Instruction Queue

(6-Word)

2 Instructions

Reservation Station Reservation Station Reservation Station

Integer Unit 1 System Register

Unit

Dispatch Unit 64-Bit

(2 Instructions)

SRs

ITLB

(Shadow) IBAT

Array 32-Kbyte

I Cache

Tags

128-Bit

(4 Instructions)

Reservation Station

32-Bit

Floating-Point

Unit

Rename Buffers

(6)

FPR File

32-Bit 64-Bit 64-Bit

Reservation Station

(2-Entry)

Load/Store Unit

(EA Calculation)

Store Queue

GPR File

Rename Buffers

(6)

32-Bit

SRs

(Original)

DTLB

DBAT

Array

64-Bit

Completion Unit

Reorder Buffer

(6-Entry)

Tags 32-Kbyte

D Cache

60x Bus Interface Unit

Instruction Fetch Queue

L1 Castout Queue

Data Load Queue L2 Controller

L2 Tags

L2 Bus Interface

Unit

L2 Castout Queue

32-Bit Address Bus

32-/64-Bit Data Bus

17-Bit L2 Address Bus

64-Bit L2 Data Bus

Integer Unit 2

PC755B/745B

2138A–HIREL–05/02

General Parameters The following list provides a summary of the general parameters of the PC755B:

Features This section summarizes features of the PC755B’s implementation of the PowerPC

architecture. Major features of the PC755B are as follows:

• Branch Processing Unit

– Four instructions fetched per clock

– One branch processed per cycle (plus resolving 2 speculations)

– Up to 1 speculative stream in execution, 1 additional speculative stream in

fetch

– 512-entry branch history table (BHT) for dynamic prediction

– 64-entry, 4-way set associative Branch Target Instruction Cache (BTIC) for

eliminating branch delay slots

• Dispatch Unit

– Full hardware detection of dependencies (resolved in the execution units)

– Dispatch two instructions to six independent units (system, branch,

load/store, fixed-point unit 1, fixed-point unit 2, floating-point)

– Serialization control (predispatch, postdispatch, execution serialization)

• Decode

– Register file access

– Forwarding control

– Partial instruction decode

• Completion

– 6 entry completion buffer

– Instruction tracking and peak completion of two instructions per cycle

– Completion of instructions in program order while supporting out-of-order

instruction execution, completion serialization and all instruction flow

changes

• Fixed Point Units (FXUs) that share 32 GPRs for Integer Operands

– Fixed Point Unit 1 (FXU1)-multiply, divide, shift, rotate, arithmetic, logical

– Fixed Point Unit 2 (FXU2)-shift, rotate, arithmetic, logical

– Single-cycle arithmetic, shifts, rotates, logical

– Multiply and divide support (multi-cycle)

Technology 0.22 µm CMOS, six-layer metal

Die size 6.61 mm x 7.73 mm (51 mm2)

Transistor count 6.75 million

Logic design Fully-static Packages

PC745B Surface mount 255 Plastic Ball Grid Array (PBGA)

PC755B Surface mount 360 Plastic Ball Grid Array (PBGA)

Core power supply 2V ± 100 mV DC (nominal; some parts support core

voltages down to 1.8V; see Table 5 for recommended

operating conditions)

I/O power supply 2.5V ± 100 mV DC or 3.3V ± 165 mV DC (input thresh-

olds are configuration pin selectable)

4PC755B/745B 2138A–HIREL–05/02

– Early out multiply

• Floating-point Unit and a 32-entry FPR File

– Support for IEEE-754 standard single and double precision floating point

arithmetic

– Hardware support for divide

– Hardware support for denormalized numbers

– Single-entry reservation station

– Supports non-IEEE mode for time-critical operations

•SystemUnit

– Executes CR logical instructions and miscellaneous system instructions

– Special register transfer instructions

• Load/Store Unit

– One cycle load or store cache access (byte, half-word, word, double-word)

– Effective address generation

– Hits under misses (one outstanding miss)

– Single-cycle unaligned access within double word boundary

– Alignment, zero padding, sign extend for integer register file

– Floating point internal format conversion (alignment, normalization)

– Sequencing for load/store multiples and string operations

– Store gathering

– Cache and TLB instructions

– Big and Little-endian byte addressing supported

– Misaligned Little-endian supported

– Level 1 Cache structure

– 32K, 32 bytes line, 8-way set associative instruction cache (iL1)

– 32K, 32 bytes line, 8-way set associative data cache (dL1)

– Cache locking for both instruction and data caches, selectable by group of

ways

– Single-cycle cache access

– Pseudo least-recently used (PLRU) replacement

– Copy-back or Write Through data cache (on a page per page basis)

– Supports all PowerPC memory coherency modes

– Non-Blocking instruction and data cache (one outstanding miss under hits)

– No snooping of instruction cache

• Level 2 (L2) Cache Interface (not implemented on PC745B)

– Internal L2 cache controller and tags; external data SRAMs

– 256K, 512K, and 1-Mbyte 2-way set associative L2 cache support

– Copyback or write-through data cache (on a page basis, or for all L2)

– Instruction-only mode and data-only mode.

– 64 bytes (256K/512K) or 128 bytes (1M) sectored line size

– Supports flow through (register-buffer) synchronous burst SRAMs, pipelined

(register-register) synchronous burst SRAMs (3-1-1-1 or strobeless 4-1-1-1)

and pipelined (register-register) late-write synchronous burst SRAMs

PC755B/745B

2138A–HIREL–05/02

– L2 configurable to direct mapped SRAM interface or split cache/direct

mapped or private memory

– Core-to-L2 frequency divisors of 1, 1.5, 2, 2.5, and 3 supported

– 64-bit data bus

– Selectable interface voltages of 2.5V and 3.3V

– Parity checking on both L2 address and data

• Memory Management Unit

– 128 entry, 2-way set associative instruction TLB

– 128 entry, 2-way set associative data TLB

– Hardware reload for TLBs

– Hardware or optional software tablewalk support

– 8 instruction BATs and 8 data BATs

– 8 SPRGs, for assistance with software tablewalks

– Virtual memory support for up to 4 hexabytes (252)ofvirtualmemory

– Real memory support for up to 4 gigabytes (232) of physical memory

• Bus Interface

– Compatible with 60X processor interface

– 32-bit address bus

– 64-bit data bus, 32-bit mode selectable

– Bus-to-core frequency multipliers of 2x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x,

7x, 7.5x, 8x, 10x supported

– Selectable interface voltages of 2.5V and 3.3V.

– Parity checking on both address and data busses

• Power Management

– Low-power design with thermal requirements very similar to PC740/750.

– Selectable interface voltage of 1.8V/2.0V can reduce power in output buffers

(compared to 3.3V)

– Three static power saving modes: doze, nap, and sleep

– Dynamic power management

• Testability

–LSSDscandesign

– IEEE 1149.1 JTAG interface

• Integrated Thermal Management Assist Unit

– One-ship thermal sensor and control logic

– Thermal Management Interrupt for software regulation of junction

temperature

6PC755B/745B 2138A–HIREL–05/02

Pin Assignments Figure 2 (in part A) shows the pinout of the PC745B, 255PBGA package as viewed from

the top surface. Part B shows the side profile of the PBGA package to indicate the direc-

tion of the top surface view.

Figure 2. Pinout of the PC745B, 255 PBGA Package as Viewed from the Top Surface

12345678 91011121314151

Not to Scale

View Die

Substrate Assembly

Encapsulant

Part B

Part A

PC755B/745B

2138A–HIREL–05/02

Figure 3 (in part A) shows the pinout of the PC755B, 360 PBGA packages as viewed

from the top surface. Part B shows the side profile of the PBGA package to indicate the

direction of the top surface view.

Figure 3. Pinout of the PC755B, 360 PBGA, CBGA and CI-CGA Packages as Viewed from the Top Surface

1234567891011121314151

Not to Scale

17 18 19

View Die

Substrate Assembly

Encapsulant

Part B

Part A

8PC755B/745B 2138A–HIREL–05/02

Pinout Listings Table 1 provides the pinout listing for the PC745B, 255 PBGA package.

Table 1. Pinout Listing for the PC745B, 255 PBGA Package

Signal Name Pin Number Active I/O

I/F Voltages Supported(1)

1.8V/2.0V 3.3V

A[0-31] C16, E4, D13, F2, D14, G1, D15, E2, D16, D4, E13, G2,

E15, H1, E16, H2, F13, J1, F14, J2, F15, H3, F16, F4, G13,

K1, G15, K2, H16, M1, J15, P1

High I/O – –

AACK L2 Low Input – –

ABB K4 Low I/O – –

AP[0-3] C1, B4, B3, B2 High I/O – –

ARTRY J4 Low I/O – –

AVDD A10 – – 2V 2V

BG L1 Low Input – –

BR B6 Low Output – –

BVSEL(3)(4)(5) B1 High Input GND 3.3V

CI E1 Low Output – –

CKSTP_IN D8 Low Input – –

CKSTP_OUT A6 Low Output – –

CLK_OUT D7 – Output – –

DBB J14 Low I/O – –

DBG N1 Low Input – –

DBDIS H15 Low Input – –

DBWO G4 Low Input – –

DH[0-31] P14, T16, R15, T15, R13, R12, P11, N11, R11, T12, T11,

R10, P9, N9, T10, R9, T9, P8, N8, R8, T8, N7, R7, T7, P6,

N6, R6, T6, R5, N5, T5, T4

High I/O – –

DL[0-31] K13, K15, K16, L16, L15, L13, L14, M16, M15, M13, N16,

N15, N13, N14, P16, P15, R16, R14, T14, N10, P13, N12,

T13,P3,N3,N4,R3,T1,T2,P4,T3,R4

High I/O – –

DP[0-7] M2, L3, N2, L4, R1, P2, M4, R2 High I/O – –

DRTRY G16 Low Input – –

GBL F1 Low I/O – –

GND C5, C12, E3, E6, E8, E9, E11, E14, F5, F7, F10, F12, G6,

G8, G9, G11, H5, H7, H10, H12, J5, J7, J10, J12, K6, K8,

K9, K11, L5, L7, L10, L12, M3, M6, M8, M9, M11, M14, P5,

P12

HRESET A7 Low Input – –

INT B15 Low Input – –

L1_TSTCLK(2) D11 High Input – –

L2_TSTCLK(2) D12 High Input – –

LSSD_MODE(2) B10 Low Input – -–

PC755B/745B

2138A–HIREL–05/02

Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals and VDD supplies power to the processor core and

the PLL (after filtering to become AVDD). These columns serve as a reference for the nominal voltage supported on a given

signal as selected by the BVSEL pin configuration of Table 4 and the voltage supplied. For actual recommended value of VIN

or supply voltages see Table 3.

2. These are test signals for factory use only and must be pulled up to OVDD for normal machine operation.

3. To allow for future I/O voltage changes, provide the option to connect BVSEL independently to either OVDD (selects 3.3V) or

to OGND (selects 1.8V/2.0V).

4. Uses one of 15 existing no-connects in PC745’s 255-BGA package.

5. Internal pull up on die.

6. Internally tied to GND in the PC745B 255-BGA package to indicate to the power supply that a low-voltage processor is

present. This signal is not a power supply input.

MCP C13 Low Input – –

NC (No-

Connect) B7,B8,C3,C6,C8,D5,D6,H4,J16,A4,A5,A2,A3,B5 – – – –

OVDD C7, E5, E7, E10, E12, G3, G5, G12, G14, K3, K5, K12, K14,

M5, M7, M10, M12, P7, P10 – – 1.8V/2.0V 3.3V

PLL_CFG[0-3] A8, B9, A9, D9 High Input – –

QACK D3 Low Input – –

QREQ J3 Low Output – –

RSRV D1 Low Output – –

SMI A16 Low Input – –

SRESET B14 Low Input – –

SYSCLK C9 – Input – –

TA H14 Low Input – –

TBEN C2 High Input – –

TBST A14 Low I/O – –

TCK C11 High Input – –

TDI(5) A11 High Input – –

TDO A12 High Output – –

TEA H13 Low Input – –

TLBISYNC C4 Low Input – –

TMS(5) B11 High Input – –

TRST(5) C10 Low Input – –

TS J13 Low I/O – –

TSIZ[0-2] A13, D10, B12 High Output – –

TT[0-4] B13, A15, B16, C14, C15 High I/O – –

WT D2 Low Output – –

VDD 2 F6, F8, F9, F11, G7, G10, H6, H8, H9, H11, J6, J8, J9, J11,

K7, K10, L6, L8, L9, L11 – – 2V 2V

VOLTDET(6) F3 High Output – –

Table 1. Pinout Listing for the PC745B, 255 PBGA Package (Continued)

Signal Name Pin Number Active I/O

I/F Voltages Supported(1)

1.8V/2.0V 3.3V

10 PC755B/745B 2138A–HIREL–05/02

Table 2 provides the pinout listing for the PC755B, 360 PBGA, CBGA and CI-CGA.

Table 2. Pinout Listing for the PC755B, 360 PBGA, CBGA and CI-CGA Packages(8)

Signal Name Pin Number Active I/O

I/F Voltages

Supported(1)

1.8V/2.0V 3.3V

A[0-31] A13, D2, H11, C1, B13, F2, C13, E5, D13, G7, F12, G3, G6, H2,

E2,L3,G5,L4,G4,J4,H7,E1,G2,F3,J7,M3,H3,J2,J6,K3,K2,

High I/O – –

AACK N3 Low Input – –

ABB L7 Low I/O – –

AP[0-3] C4, C5, C6, C7 High I/O – –

ARTRY L6 Low I/O – –

AVDD A8 - - 2V 2V

BG H1 Low Input – –

BR E7 Low Output – –

BVSEL(3)(5)(6) W1 High Input GND 3.3V

CI C2 Low Output – –

CKSTP_IN B8 Low Input – –

CKSTP_OUT D7 Low Output – –

CLK_OUT E3 – Output – –

DBB K5 Low I/O – –

DBDIS G1 Low Input – –

DBG K1 Low Input – –

DBWO D1 Low Input – –

DH[0-31] W12, W11, V11, T9, W10, U9, U10, M11, M9, P8, W7, P9, W9,

R10,W6,V7,V6,U8,V9,T7,U7,R7,U6,W5,U5,W4,P7,V5,V4,

W3, U4, R5

High I/O – –

DL[0-31] M6, P3, N4, N5, R3, M7, T2, N6, U2, N7, P11, V13, U12, P12, T13,

W13, U13, V10, W8, T11, U11, V12, V8, T1, P1, V1, U1, N1, R2,

V3, U3, W2

High I/O – –

DP[0-7] L1, P2, M2, V2, M1, N2, T3, R1 High I/O – –

DRTRY H6 Low Input – –

GBL B1 Low I/O – –

GND D10, D14, D16, D4, D6, E12, E8, F4, F6, F10, F14, F16, G9, G11,

H5, H8, H10, H12, H15, J9, J11, K4, K6, K8, K10, K12, K14, K16,

L9, L11,M5, M8, M10, M12, M15, N9,N11, P4, P6, P10,P14, P16,

R8, R12, T4, T6, T10, T14, T16

––GNDGND

HRESET B6 Low Input – –

INT C11 Low Input – –

L1_TSTCLK(2) F8 High Input – –

L2ADDR[0-16] L17, L18, L19, M19, K18, K17, K15, J19, J18, J17, J16, H18, H17,

J14, J13, H19, G18 High Output – –

PC755B/745B

2138A–HIREL–05/02

L2AVDD L13 – – 2V 2V

L2CE P17 Low Output – –

L2CLKOUTA N15 – Output – –

L2CLKOUTB L16 – Output – –

L2DATA[0-63] U14, R13, W14, W15, V15, U15, W16, V16, W17, V17, U17, W18,

V18, U18, V19, U19, T18, T17, R19, R18, R17, R15, P19, P18,

P13, N14, N13, N19, N17, M17, M13, M18, H13, G19, G16, G15,

G14, G13, F19, F18, F13, E19, E18, E17, E15, D19, D18, D17,

C18, C17, B19, B18, B17, A18, A17, A16, B16, C16, A14, A15,

C15, B14, C14, E13

High I/O – –

L2DP[0-7] V14, U16, T19, N18, H14, F17, C19, B15 High I/O – –

L2OVDD D15, E14, E16, H16, J15, L15, M16, P15, R14, R16, T15, F15 – – 1.8V/2V 3.3V

L2SYNC_IN L14 – Input – –

L2SYNC_OUT M14 – Output – –

L2_TSTCLK(2) F7 High Input – –

L2VSEL(1)(3)(5)(6) A19 High Input GND 3.3V

L2WE N16 Low Output – –

L2ZZ G17 High Output – –

LSSD_MODE(2) F9 Low Input – –

MCP B11 Low Input – –

NC (No-Connect) B3, B4, B5, W19, K9, K114,K19

4–– ––

OVDD D5,D8,D12,E4,E6,E9,E11,F5,H4,J5,L5,M4,P5,R4,R6,R9,

R11, T5, T8, T12 ––1.8V/2V3.3V

PLL_CFG[0-3] A4, A5, A6, A7 High Input – –

QACK B2 Low Input – –

QREQ J3 Low Output – –

RSRV D3 Low Output – –

SMI A12 Low Input – –

SRESET E10 Low Input – –

SYSCLK H9 – Input – –

TA F1 Low Input – –

TBEN A2 High Input – –

TBST A11 Low I/O – –

TCK B10 High Input – –

TDI(6) B7 High Input – –

TDO D9 High Output – –

Table 2. Pinout Listing for the PC755B, 360 PBGA, CBGA and CI-CGA Packages(8) (Continued)

Signal Name Pin Number Active I/O

I/F Voltages

Supported(1)

1.8V/2.0V 3.3V

12 PC755B/745B 2138A–HIREL–05/02

Notes: 1. OVDD supplies power to the processor bus, JTAG, and all control signals except the L2 cache controls (L2CE, L2WE, and

L2ZZ); L2OVDD supplies power to the L2 cache interface (L2ADDR[0-16], L2DATA[0-63], L2DP[0-7] and L2SYNC-OUT)

and the L2 control signals; and VDD supplies power to the processor core and the PLL and DLL (after filtering to become

AVDD and L2AVDD respectively). These columns serve as a reference for the nominal voltage supported on a given signal as

selected by the BVSEL/L2VSEL pin configurations of Table 4 and the voltage supplied. For actual recommended value of

VIN or supply voltages see Table 5.

2. These are test signals for factory use only and must be pulled up to OVDD for normal machine operation.

3. To allow for future I/O voltage changes, provide the option to connect BVSEL and L2VSEL independently to either OVDD

(selects 3.3V) or to OGND (selects 1.8V/2.0V).

4. These pins are reserved for potential future use as additional L2 address pins.

5. Uses one of 9 existing no-connects in PC750’s 360-BGA package.

6. Internal pull up on die.

7. Internally tied to L2OVDD in the PC755B 360-BGA package to indicate the power present at the L2 cache interface. This sig-

nal is not a power supply input.

8. This is different from the PC745B 255-BGA package.

TEA J1 Low Input – –

TLBISYNC A3 Low Input – –

TMS(6) C8 High Input – –

TRST(6) A10 Low Input – –

TS K7 Low I/O – –

TSIZ[0-2] A9, B9, C9 High Output – –

TT[0-4] C10, D11, B12, C12, F11 High I/O – –

WT C3 Low Output – –

VDD G8, G10, G12, J8, J10, J12, L8, L10, L12, N8, N10, N12 – – 2V 2V

VOLTDET(7) K13 High Output – –

Table 2. Pinout Listing for the PC755B, 360 PBGA, CBGA and CI-CGA Packages(8) (Continued)

Signal Name Pin Number Active I/O

I/F Voltages

Supported(1)

1.8V/2.0V 3.3V

PC755B/745B

2138A–HIREL–05/02

Signal Description

Figure 4. PC755B Microprocessor Signal Groups

ABB

TT[0-4]

AP[0-3]

TBST

TS1Z[0-2]

GBL

AACK

ARTRY

DBG

DBWO

DBB

L2ADDR [16-0]

L2DAT A [0-63]

L2DP [0-7]

L2CLK-OUT [A-B]

L2WE

A[0-31] L2SYNC_OUT

L2SYNC_IN

INT

SMI

MCP

HRESET

CKSTP_IN

CKSTP_OUT

SYSCLK,

PLL_CFG [0-3]

Factory Test

JTAG:COP

ADDRESS

ARBITRATION

ADDRESS

START

ADDRESS

BUS

TRANSFER

ATTRIBUTE

ADDRESS

TERMINATION

DATA

ARBITRATION

L2 CACHE

L2 VSEL

ADDRESS/

DATA

L2 CACHE

CLOCK/CONTROL

INTERRUPTS

RESET

CLOCK

CONTROL

TEST INTERFACE

D[0-63]

DATA

TRANSFER D[P0-7]

DBDIS

DATA

TERMINATION DRTRY

TEA

PC755B

L2AVDD

L2VDD

SRESET

RSRV

TBEN

TLBISYNC

QREQ

QACK

PROCESSOR

STATUS

CONTROL

CLK_OUT

VDD AVDD

L2CE

L2ZZ

Not supported in the PC745B

GND

OVDD

VOLTDET

14 PC755B/745B 2138A–HIREL–05/02
Detailed
Specification
Scope This drawing describes the specific requirements for the microprocessor PC755B, in
compliance with Atmel Grenoble standard screening.
Applicable Documents 1) MIL-STD-883: Test methods and procedures for electronics.
2) MIL-PRF-38535 appendix A: General specifications for microcircuits.
Requirements
General The microcircuits are in accordance with the applicable documents and as specified
herein.
Design and Construction
Terminal Connections Depending on the package, the terminal connections is shown in Table 1, Table 2 and
Figure 4.
Absolute Maximum Rating
Notes: 1. Functional and tested operating conditions are given in Table 4. Absolute maximum ratings are stress ratings only, and func-
tional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. Caution: VIN must not exceed OVDD or L2OVDD by more than 0.3V at any time including during power-on reset.
3. Caution: L2OVDD/OVDD must not exceed VDD/AVDD/L2AVDD by more than 1.6V during normal operation; this limit may be
exceeded for a maximum of 20 ms during power-on reset and power-down sequences.
4. Caution: VDD/AVDD/L2AVDD must not exceed L2OVDD/OVDD by more than 0.4V during normal operation; this limit may be
exceeded for a maximum of 20 ms during power-on reset and power-down sequences.
5. VIN may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2.
Table 3. Absolute Maximum Ratings(1)
Characteristic Symbol Maximum Value Unit
Core supply voltage(4) VDD -0.3 to 2.5 V
PLL supply voltage(4) AVDD -0.3 to 2.5 V
L2 DLL supply voltage(4) L2AVDD -0.3 to 2.5 V
Processor bus supply voltage(3) OVDD -0.3 to 3.6 V
L2 bus supply voltage(3) L2OVDD -0.3 to 3.6 V
Input voltage Processor bus(2)(5) Vin -0.3 to OVDD +0.3V V
L2 Bus(2)(5) Vin -0.3 to L2OVDD +0.3V V
JTAG Signals Vin -0.3 to 3.6 V
Storage temperature range Tstg -55to150 °C

PC755B/745B

2138A–HIREL–05/02

Figure 5 shows the allowable undershoot and overshoot voltage on the PC755B and

PC745B.

Figure 5. Overshoot/Undershoot Voltage

The PC755B provides several I/O voltages to support both compatibility with existing

systems and migration to future systems. The PC755B core voltage must always be

provided at nominal 2.0V (see Table 5 for actual recommended core voltage). Voltage to

the L2 I/Os and Processor Interface I/Os are provided through separate sets of supply

pins and may be provided at the voltages shown in Table 4. The input voltage threshold

for each bus is selected by sampling the state of the voltage select pins BVSEL and

L2VSEL during operation. These signals must remain stable during part operation and

cannot change. The output voltage will swing from GND to the maximum voltage applied

to the OVDD or L2OVDD power pins.

Table 4 describes the input threshold voltage setting.

Notes: 1. The input threshold settings above are different for all revisions prior to Rev 2.8 (Rev E). For more information, contact your

local Atmel sales office.

2. Caution: The input threshold selection must agree with the OVDD/L2OVDD voltages supplied.

(L2) OVDD +20%

(L2) OVDD +5%

(L2) OVDD

Gnd - 1.0V

Gnd - 0.3V

Gnd

VIH

Not to exceed 10%

of tSYSCLK

VIL

Table 4. Input Threshold Voltage Setting

Part Revision BVSEL Signal L2VSEL Signal Processor Bus Interface Voltage L2 Bus Interface Voltage

E 0 0 Not Available Not Available

0 1 Not Available 2.5V/3.3V

1 0 2.5V/3.3V Not Available

1 1 2.5V/3.3V 2.5V/3.3V

16 PC755B/745B 2138A–HIREL–05/02
Notes: 1. These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not
guaranteed.
2. Revisions prior to Rev. 2.8 (Rev. E) offered different I/O voltage support.
3. 2.0V nominal.
4. 2.5V nominal.
5. 3.3V nominal.
Thermal Characteristics
Package Characteristics Table 6 provides the package thermal characteristics for the PC755B.
Notes: 1. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) tempera-
ture, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3. Per JEDEC JESD51-6 with the board horizontal.
Table 5. Recommended Operating Conditions(1)
Recommended Value
Unit300 MHz, 350 MHz 400 MHz
Characteristic Symbol Min Max Min Max
Core supply voltage(3) VDD 1.80 2.10 1.90 2.10 V
PLL supply voltage(3) AVDD 1.80 2.10 1.90 2.10 V
L2 DLL supply voltage(3) L2AVDD 1.80 2.10 1.90 2.10 V
Processor bus supply
voltage(2)(4)(5) BVSEL = 1 OVDD 2.375 2.625 2.375 2.625 V
3.135 3.465 3.135 3.465 V
L2 bus supply voltage(2)(4)(5) L2VSEL = 1 L2OVDD 2.375 2.625 2.375 2.625 V
3.135 3.465 3.135 3.465 V
Input voltage Processor bus Vin GND OVDD GND OVDD V
L2 Bus Vin GND L2OVDD GND L2OVDD V
JTAG Signals Vin GND OVDD GND OVDD V
Die-junction temperature Military temperature range Tj-55 125 -55 125 °C
Industrial temperature Tj-40 40
Table 6. Package Thermal Characteristics
Characteristic Symbol
Value
Unit
PC755
CBGA PC755
PBGA PC745
PBGA
Junction-to-ambient thermal resistance, natural convection(1)(2) RθJA 24 31 34 °C/W
Junction-to-ambient thermal resistance, natural convection, four-layer
(2s2p) board(1)(3) RθJMA 17 25 26 °C/W
Junction-to-ambient thermal resistance, 200 ft./min. airflow, single-layer
(1s) board(1)(3) RθJMA 18 25 27 °C/W
Junction-to-ambient thermal resistance, 200 ft./min. airflow, four-layer
(2s2p) board(1)(3) RθJMA 14 21 22 °C/W
Junction-to-board thermal resistance(4) RθJB 81717°C/W
Junction-to-case thermal resistance(5) RθJC <0.1 <0.1 <0.1 °C/W

PC755B/745B

2138A–HIREL–05/02

4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on

the top surface of the board near the package.

5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883

Method 1012.1) with the calculated case temperature. The actual value of RÉýJC for the part is less than 0.1°C/W.

Note: Refer to Section “Thermal Management Information“ page 18 for more details about thermal management.

The board designer can choose between several types of heat sinks to place on the

PC755B. There are several commercially-available heat sinks for the PC755B provided

by the following vendors:

For the exposed-die packaging technology, shown in Table 5, the intrinsic conduction

thermal resistance paths are as follows:

• The die junction-to-case (or top-of-die for exposed silicon) thermal resistance

• The die junction-to-ball thermal resistance

Figure 6 depicts the primary heat transfer path for a package with an attached heat sink

mounted to a printed-circuit board.

Heat generated on the active side of the chip is conducted through the silicon, then

through the heat sink attach material (or thermal interface material), and finally to the

heat sink where it is removed by forced-air convection.

Since the silicon thermal resistance is quite small, for a first-order analysis, the tempera-

ture drop in the silicon may be neglected. Thus, the heat sink attach material and the

heat sink conduction/convective thermal resistances are the dominant terms.

Figure 6. C4 Package with Head Sink Mounted to a Printed-circuit Board

Note the internal versus external package resistance.

External Resistance

Internal Resistance

Radiation Convection

Heat Sink

Printed ± Circuit Board

Thermal Interface Material

Package/Leads

Die Junction

Die/Package

18 PC755B/745B 2138A–HIREL–05/02

Thermal Management

Assistance The PC755B incorporates a thermal management assist unit (TAU) composed of a ther-

mal sensor, digital-to-analog converter, comparator, control logic, and dedicated

special-purpose registers (SPRs). Specifications for the thermal sensor portion of the

TAU are found in Table 7. More information on the use of this feature is given in the

Motorola PC755B RISC Microprocessor User’s manual.

Notes: 1. The temperature is the junction temperature of the die. The thermal assist unit’s raw

output does not indicate an absolute temperature, but must be interpreted by soft-

ware to derive the absolute junction temperature. For information about the use and

calibration of the TAU, see Motorola Application Note AN1800/D, “Programming the

Thermal Assist Unit in the PC750 Microprocessor”.

2. The comparator settling time value must be converted into the number of CPU clocks

that need to be written into the THRM3 SPR.

3. Guaranteed by design and characterization.

Thermal Management

Information This section provides thermal management information for the ceramic ball grid array

(BGA) package for air-cooled applications. Proper thermal control design is primarily

dependent upon the system-level design-the heat sink, airflow and thermal interface

material. To reduce the die-junction temperature, heat sinks may be attached to the

package by several methods-adhesive, spring clip to holes in the printed-circuit board or

package, and mounting clip and screw assembly; see Figure 7. This spring force should

not exceed 5.5 pounds of force.

Figure 7. Package Exploded Cross-Sectional View with Several Heat Sink Options

Table 7. Thermal Sensor Specifications at Recommended Operating Conditions

(see Table 5)

Characteristic Min Max Unit

Temperature range(1) 0127°C

Comparator settling time(2)(3) 20 – s

Resolution(3) 4–°C

Accuracy(3) -12 +12 °C

Adhesive

Thermal Interface Material

Heat Sink

Clip

Printed ± Circuit Board Option

BGA Package

PC755B/745B

2138A–HIREL–05/02

Ultimately, the final selection of an appropriate heat sink depends on many factors, such

as thermal performance at a given air velocity, spatial volume, mass, attachment

method, assembly, and cost.

Adhesives and Thermal

Interface Materials Figure 8. Thermal Performance of Select Thermal Interface Material

A thermal interface material is recommended at the package lid-to-heat sink interface to

minimize the thermal contact resistance. For those applications where the heat sink is

attached by spring clip mechanism, Figure 8 shows the thermal performance of three

thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint,

and a joint with thermal grease as a function of contact pressure. As shown, the perfor-

mance of these thermal interface materials improves with increasing contact pressure.

The use of thermal grease significantly reduces the interface thermal resistance. That is,

the bare joint results in a thermal resistance approximately 7 times greater than the ther-

mal grease joint.

Heat sinks are attached to the package by means of a spring clip to holes in the printed-

circuit board (see Figure 7). This spring force should not exceed 5.5 pounds of force.

Therefore, the synthetic grease offers the best thermal performance, considering the

low interface pressure.

The board designer can choose between several types of thermal interface. Heat sink

adhesive materials should be selected based upon high conductivity, yet adequate

mechanical strength to meet equipment shock/vibration requirements.

Heat Sink Selection Example For preliminary heat sink sizing, the die-junction temperature can be expressed as

follows:

Tj=T

a+T

r+(θjc +θint +θsa)*P

Where:

Tjis the die-junction temperature

0.5

1.5

2Silicone Sheet (0.006 inch)

Bare Joint

Floroether Oil Sheet (0.007 inch)

Graphite/Oil Sheet (0.005 inch)

Synthetic Grease

Contact Pressure (psi)

Specific

Thermal

Resistance

(Kin2/W)

01020304050607080

20 PC755B/745B 2138A–HIREL–05/02

Tais the inlet cabinet ambient temperature

Tris the air temperature rise within the computer cabinet

θjc is the junction-to-case thermal resistance

θint is the adhesive or interface material thermal resistance

θsa is the heat sink base-to-ambient thermal resistance

Pdis the power dissipated by the device

During operation the die-junction temperatures (Tj) should be maintained less than the

value specified in Table 5. The temperature of the air cooling the component greatly

depends upon the ambient inlet air temperature and the air temperature rise within the

electronic cabinet. An electronic cabinet inlet-air temperature (Ta) may range from 30 to

40°C. The air temperature rise within a cabinet (Tr) may be in the range of 5 to 10°C.

The thermal resistance of the thermal interface material (θint) is typically about 1°C/W.

AssumingaT

aof 30°C, a Trof5

oC, a CBGA package θjc = 0.03, and a power consump-

tion (Pd) of 5.0 watts, the following expression for Tjis obtained:

Die-junction temperature: Tj=30°C+5°C+(0.03°C/W + 1.0°C/W + θsa)*5.0W

For a Thermalloy heat sink #2328B, the heat sink-to-ambient thermal resistance (θsa)

versus airflow velocity is shown in Figure 9.

Figure 9. Thermalloy #2328B Heat Sink-to-Ambient Thermal Resistance Versus Air-

flow Velocity

Assuming an air velocity of 0.5 m/s, we have an effective Rsa of 7°C/W, thus

Tj=30°C+ 5°C+ (0.03°C/W +1.0°C/W + 7°C/W) * 5.0 W,

resulting in a die-junction temperature of approximately 81°C which is well within the

maximum operating temperature of the component.

0 0.5 1 1.5 2 2.5 3 3.5

Thermalloy #2328B Pin±fin Heat Sink

Approach Air Velocity (m/s)

(25 x28 x 15 mm)

Heat Sink Thermal Resistance °C/W)

PC755B/745B

2138A–HIREL–05/02

Other heat sinks offered by Chip Coolers, IERC, Thermalloy, Wakefield Engineering,

and Aavid Engineering offer different heat sink-to-ambient thermal resistances, and may

or may not need air flow.

Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances

are a common figure-of-merit used for comparing the thermal performance of various

microelectronic packaging technologies, one should exercise caution when only using

this metric in determining thermal management because no single parameter can ade-

quately describe three-dimensional heat flow. The final die-junction operating

temperature, is not only a function of the component-level thermal resistance, but the

system-level design and its operating conditions. In addition to the component’s power

consumption, a number of factors affect the final operating die-junction temperature—

airflow, board population (local heat flux of adjacent components), heat sink efficiency,

heat sink attach, heat sink placement, next-level interconnect technology, system air

temperature rise, altitude, etc.

Due to the complexity and the many variations of system-level boundary conditions for

today’s microelectronic equipment, the combined effects of the heat transfer mecha-

nisms (radiation, convection and conduction) may vary widely. For these reasons, we

recommend using conjugate heat transfer models for the board, as well as, system-level

designs. To expedite system-level thermal analysis, several “compact” thermal-package

models are available within FLOTHERM®. These are available upon request.

Power consideration

Power management The PC755B provides four power modes, selectable by setting the appropriate control

bits in the MSR and HIDO registers. The four power modes are as follows:

• Full-power: This is the default power state of the PC755B. The PC755B is fully

powered and the internal functional units operate at the full processor clock speed.

If the dynamic power management mode is enabled, functional units that are idle

will automatically enter a low-power state without affecting performance, software

execution, or external hardware.

• Doze: All the functional units of the PC755B are disabled except for the time

base/decrementer registers and the bus snooping logic. When the processor is in

doze mode, an external asynchronous interrupt, a system management interrupt, a

decrementer exception, a hard or soft reset, or machine check brings the PC755B

into the full-power state. The PC755B in doze mode maintains the PLL in a fully

powered state and locked to the system external clock input (SYSCLK) so a

transition to the full-power state takes only a few processor clock cycles.

• Nap: The nap mode further reduces power consumption by disabling bus snooping,

leaving only the time base register and the PLL in a powered state. The PC755B

returns to the full-power state upon receipt of an external asynchronous interrupt, a

system management interrupt, a decrementer exception, a hard or soft reset, or a

machine check input (MCP). A return to full-power state from a nap state takes only

a few processor clock cycles. When the processor is in nap mode, if QACK is

negated, the processor is put in doze mode to support snooping.

• Sleep: Sleep mode minimizes power consumption by disabling all internal functional

units, after which external system logic may disable the PPL and SUSCLK.

Returning the PC755B to the full-power state requires the enabling of the PPL and

SYSCLK, followed by the assertion of an external asynchronous interrupt, a system

management interrupt, a hard or soft reset, or a machine check input (MCP) signal

after the time required to relock the PPL.

22 PC755B/745B 2138A–HIREL–05/02
Power Dissipation
Notes: 1. These values apply for all valid processor bus and L2 bus ratios. The values do not
include I/O Supply Power (OVDD and L2OVDD)orPLL/DLLsupplypower(AV
DD and
L2AVDD). OVDD and L2OVDD power is system dependent, but is typically <10% of VDD
power. Worst case power consumption for AVDD = 15 mW and L2AVDD =15mW.
2. Maximum power is measured at 105°C and VDD = 2.0V while running an entirely
cache-resident, contrived sequence of instructions which keep the execution units
maximally busy.
3. Typical power is an average value measured at 65°CandV
DD = 2.0V in a system
executing typical applications and benchmark sequences.
Table 8. Power Consumption for PC755
Processor (CPU) Frequency
Unit300 MHz 350 MHz 400 MHz
Full-on Mode
Typical(1)(3) 3.1 3.6 4 W
Maximum(1)(2) 4.5 5.3 6 W
Doze Mode
Maximum(1)(2) 1.8 2 2.3 W
Nap Mode
Maximum(1)(2) 111W
Sleep Mode
Maximum(1)(2) 460 470 470 mW
Sleep Mode-PLL and DLL Disabled
Typical(1)(3) 340 340 340 mW
Maximum(1)(2) 430 430 430 mW

23
PC755B/745B
2138A–HIREL–05/02
Electrical
Characteristics
Static Characteristics
Notes: 1. Nominal voltages; See Table 5 for recommended operating conditions.
2. For processor bus signals, the reference is OVDD while L2OVDD is the reference for the L2 bus signals.
3. Excludes test signals (LSSD_MODE, L1_TSTCLK, L2_TSTCLK) and IEEE 1149.1 boundary scan (JTAG) signals.
4. Capacitance is periodically sampled rather than 100% tested.
5. The leakage is measured for nominal OVDD and VDD,orbothOV
DD and VDD must vary in the same direction (for example,
both OVDD and VDD vary by either +5% or -5%).
Dynamic Characteristics After fabrication, parts are sorted by maximum processor core frequency as shown in
the “Clock AC Specifications” Section on page 24 and tested for conformance to the AC
specifications for that frequency. These specifications are for 275, 300, 333 MHz pro-
cessor core frequencies. The processor core frequency is determined by the bus
(SYSCLK) frequency and the settings of the PLL_CFG[0-3] signals. Parts are sold by
maximum processor core frequency.
Table 9. DC Electrical Specifications at Recommended Operating Conditions (see Table 5)
Characteristic Nominal bus
Voltage(1) Symbol Min Max Unit
Input high voltage (all inputs except SYSLCK)(2)(3) 2.5 VIH 1.6 (L2)OVDD +0.3 V
3.3 VIH 2(L2)OV
DD +0.3 V
Input low voltage (all inputs except SYSLCK)(2) 2.5 VIL -0.3 0.6 V
3.3 VIL -0.3 0.8 V
SYSCLK input high voltage 2.5 KVIH 1.8 OVDD +0.3 V
3.3 KVIH 2.4 OVDD +0.3 V
SYSCLK input low voltage 2.5 KVIL -0.3 0.4 V
3.3 KVIL -0.3 0.4 V
Input leakage current, (2)(3)
VIN = L2OVDD/OVDD
Iin –10µA
Hi-Z (off-state) leakage current, (2)(3)(5)
VIN = L2OVDD/OVDD
ITSI –10µA
Output high voltage, IOH =-6mA 2.5 V
OH 1.7 – V
3.3 VOH 2.4 – V
Output low voltage, IOL =6mA 2.5 V
OL –0.45V
3.3 VOL –0.4V
Capacitance, VIN =0V,f=1MHz(3)(4) Cin –5pF

24 PC755B/745B 2138A–HIREL–05/02
Clock AC Specifications Table 10 provides the clock AC timing specifications as defined in Table 3.
Notes: 1. Caution: The SYSCLK frequency and PLL_CFG[0-3] settings must be chosen such that the resulting SYSCLK (bus) fre-
quency, CPU (core) frequency, and PLL (VCO) frequency do not exceed their respective maximum or minimum operating
frequencies. Refer to the PLL_CFG[0-3] signal description in Table 17,” for valid PLL_CFG[0-3] settings
2. Rise and fall times measurements are now specified in terms of slew rates, rather than time to account for selectable I/O bus
interface levels. The minimum slew rate of 1v/ns is equivalent to a 2ns maximum rise/fall time measured at 0.4V and 2.4V or
a rise/fall time of 1ns measured at 0.4V to 1.4V.
3. Timing is guaranteed by design and characterization.
4. This represents total input jitter – short term and long term combined and is guaranteed by design.
5. Relock timing is guaranteed by design and characterization. PLL-relock time is the maximum amount of time required for
PLL lock after a stable VDD and SYSCLK are reached during the power-on reset sequence. This specification also applies
when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must be held
asserted for a minimum of 255 bus clocks after the PLL-relock time during the power-on reset sequence.
Figure 10 provides the SYSCLK input timing diagram.
Figure 10. SYSCLK Input Timing Diagram
Table 10. Clock AC Timing Specifications at Recommended Operating Conditions (See Table 5)
Characteristic Symbol
Maximum Processor Core Frequency
Unit300 MHz 350 MHz 400 MHz
Min Max Min Max Min Max
Processor frequency(1) fcore 200 300 200 350 200 400 MHz
VCO frequency(1) fVCO 400 600 400 700 400 800 MHz
SYSCLK frequency(1) fSYSCLK 25 100 25 100 25 100 MHz
SYSCLK cycle time tSYSCLK 10 40 10 40 10 40 ns
SYSCLK rise and fall time(2) tKR &t
KF –2–2–2 ns
tKR &t
KF –1–1–1 ns
SYSCLK duty cycle measured at OVDD/2(3) tKHKL/tSYSCLK 40 60 40 60 40 60 %
SYSCLK jitter(3)(4) – 150 – 150 – 150 ps
Internal PLL relock time(3)(5) – 100 – 100 – 100 µs
SYSCLK VMVMVM
KVIH
KVIL
VM = Midpoint Voltage (OVDD/2)
tSYSCLK
tKR tKF
tKHKL

25
PC755B/745B
2138A–HIREL–05/02
Processor Bus AC
Specifications Table 11 provides the processor bus AC timing specifications for the PC755B as defined
in Figure 11 and Figure 13. Timing specifications for the L2 bus are provided in Section
“L2 Clock AC Specifications» page 27.
Notes: 1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input
SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the sig-
nal in question. All output timings assume a purely resistive 50Ωload (See Figure 11). Input and output timings are
measured at the pin; time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. THe symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs and
t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid state (V) relative
to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV symbolizes the time from SYSCLK(K)
going highs) until outputs (O) are valid (V) or output valid time. Input hold time can be read as the time that the input signal
(I) went invalid (X) with respect to the rising clock edge (KH) -note the position of the reference and its state for inputs –and
output hold time can be read as the time from the rising edge (KH) until the output went invalid (OX). For additional explana-
tion of AC timing specifications in Motorola PowerPC microprocessors, see the application note “Understanding AC Timing
Specifications for PowerPC Microprocessors.”
3. The setup and hold time is with respect to the rising edge of HRESET (see Figure 11).
4. This specification is for configuration mode select only. Also note that the HRESET must be held asserted for a minimum of
255 bus clocks after the PLL re-lock time during the power-on reset sequence.
5. tSYSCLK is the period of the external clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied
by the period of SYSCLK to compute the actual time duration (in nanoseconds) of the parameter in question.
6. Mode select signals are BVSEL, L2VSEL, PLL_CFG[0-3]
7. Guaranteed by design and characterization.
8. Bus mode select pins must remain stable during operation. Changing the logic states of BVSEL or L2VSEL during operation
will cause the bus mode voltage selection to change. Changing the logic states of the PLL_CFG pins during operation will
cause the PLL division ratio selection to change. Both of these conditions are considered outside the specification and are
not supported. Once HRESET is negated the states of the bus mode selection pins must remain stable.
Figure 11 provides the mode select input timing diagram for the PC755B.
Figure 11. Mode Input Timing Diagram
Table 11. Processor Bus Mode Selection AC Timing Specifications(1)
At VDD =AVDD =2.0V100mV;-55≤ Tj≤ +125°C, OVDD = 3.3V 165 mV and OVDD =1.8V±100 mV and OVDD =2.0V100mV
Parameter
Symbols(2) All Speed Grades
UnitMin Max
Mode select input setup to HRESET(3)(4)(5)(6)(7) tMVRH 8–t
SYSCLk
HRESET to mode select input hold(3)(4)(6)(7)(8) tMXRH 0–ns
HRESET
MODE SIGNALS
VM = Midpoint Voltage (OVDD/2)
VM
tMVRH tMXRH

26 PC755B/745B 2138A–HIREL–05/02
Figure 12 provides the AC test load for the PC755B.
Figure 12. AC Test Load
Notes: 1. Revisions prior to Rev 2.8 (Rev E) were limited in performance and did not conform to this specification. Contact your local
Motorola sales office for more information.
2. Guaranteed by design and characterization.
3. tSYSCLK is the period of the external clock (SYSCLK) in nanoseconds (ns). The numbers given in the table must be multiplied
by the period of SYSCLK to compute the actual time duration (in ns) of the parameter in question.
4. Per the 60x bus protocol, TS, ABB and DBB are driven only by the currently active bus master. They are asserted low then
precharged high before returning to high-Z as shown in Figure 6. The nominal precharge width for TS, ABB or DBB is 0.5 x
tSYSCLK, i.e. less than the minimum tSYSCLK period, to ensure that another master asserting TS, ABB,orDBBon the following
clock will not contend with the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid
time is tested for precharge.The high-Z behavior is guaranteed by design.
5. Per the 60x bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following
AACK. Bus contention is not an issue since any master asserting ARTRY will be driving it low. Any master asserting it low in
the first clock following AACK will then go to high-Z for one clock before precharging it high during the second cycle after the
assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK; i.e., it should be high-Z as shown in Figure 6
before the first opportunity for another master to assert ARTRY. Output valid and output hold timing is tested for the signal
asserted. Output valid time is tested for precharge. The high-Z and precharge behavior is guaranteed by design.
OVDD/2
OUTPUT Z0 = 50Ω
RL = 50Ω
Table 12. Processor Bus AC Timing Specifications(1) at Recommended Operating Conditions
Parameter Symbols
All Speed Grades Unit
Min Max
Setup Times: All Inputs tIVKH 2.5 – ns
Input Hold Times: TLBISYNC,MCP,SMI tIXKH 0.6 – ns
Input Hold Times: All Inputs, except TLBISYNC,MCP,SMI tIXKH 0.2 – ns
Valid Times: All Outputs tKHOV –4.1ns
Output Hold Times: All Outputs tKHOX 1–ns
SYSCLK to Output Enable(2) tKHOE 0.5 – ns
SYSCLK to Output High Impedance (all except ABB, ARTRY,DBB)(2) tKHOZ –6ns
SYSCLK to ABB,DBBHigh Impedance After Precharge(2)(3)(4) tKHABPZ –1t
SYSCLK
Maximum Delay to ARTRY Precharge(2)(3)(5) tKHARP –1t
SYSCLK
SYSCLK to ARTRY High Impedance After Precharge(2)(3)(5) tKHARPZ –2t
SYSCLK

PC755B/745B

2138A–HIREL–05/02

Figure 13 provides the input/output timing diagram for the PC755B.

Figure 13. Input/Output Timing Diagram

L2 Clock AC Specifications The L2CLK frequency is programmed by the L2 Configuration Register (L2CR[4:6])

core-to-L2 divisor ratio. See Table 13 for example core and L2 frequencies at various

divisors. Table 13 provides the potential range of L2CLK output AC timing specifications

as defined in Figure 14.

The minimum L2CLK frequency of Table 13 is specified by the maximum delay of the

internal DLL. The variable-tap DLL introduces up to a full clock period delay in the

L2CLKOUTA, L2CLKOUTB, and L2SYNC_OUT signals so that the returning

L2SYNC_IN signal is phase aligned with the next core clock (divided by the L2 divisor

ratio). Do not choose a core-to-L2 divisor which results in an L2 frequency below this

minimum, or the L2CLKOUT signals provided for SRAM clocking will not be phase

aligned with the PC755B core clock at the SRAMs.

The maximum L2CLK frequency shown in Table 13 is the core frequency divided by

one. Very few L2 SRAM designs will be able to operate in this mode. Most designs will

select a greater core-to-L2 divisor to provide a longer L2CLK period for read and write

access to the L2 SRAMs. The maximum L2CLK frequency for any application of the

PC755B will be a function of the AC timings of the PC755B, the AC timings for the

SRAM, bus loading, and printed circuit board trace length.

Motorola is similarly limited by system constraints and cannot perform tests of the L2

interface on a socketed part on a functional tester at the maximum frequencies of Table

13. Therefore functional operation and AC timing information are tested at core-to-L2

divisors of 2 or greater. Functionality of core-to-L2 divisors of 1 or 1.5 is verified at less

than maximum rated frequencies.

SYSCLK

ALL INPUTS

VM = Midpoint Voltage (OVDD/2 or Vin/2)

ALL OUTPUT S

(Except TS, ABB,

ARTRY, DBB)

TS,ABB,DBB

ARTRY

tIVKH tIXKH

tKHOE

tKHOV tKHOX

tKHABPZ

tKHOV

tKHOX

tKHOZ

tKHARPZ

tKHOV

tKHOX

tKHARP

tKHOV

tKHOZ

28 PC755B/745B 2138A–HIREL–05/02
L2 input and output signals are latched or enabled respectively by the internal L2CLK
(which is SYSCLK multiplied up to the core frequency and divided down to the L2CLK
frequency). In other words, the AC timings of Table 14 and Table 15 are entirely inde-
pendent of L2SYNC_IN. In a closed loop system, where L2SYNC_IN is driven through
the board trace by L2SYNC_OUT, L2SYNC_IN only controls the output phase of
L2CLKOUTA and L2CLKOUTB which are used to latch or enable data at the SRAMs.
However, since in a closed loop system L2SYNC_IN is held in phase alignment with the
internal L2CLK, the signals of Table 14 and Table 15 are referenced to this signal rather
than the not-externally-visible internal L2CLK. During manufacturing test, these times
are actually measured relative to SYSCLK.
The L2SYNC_OUT signal is intended to be routed halfway out to the SRAMs and then
returned to the L2SYNC_IN input of the PC755B to synchronize L2CLKOUT at the
SRAM with the processor’s internal clock. L2CLKOUT at the SRAM can be offset for-
ward or backward in time by shortening or lengthening the routing of L2SYNC_OUT to
L2SYNC_IN. See Motorola Application Note AN179/D “PowerPC™Backside L2 Timing
Analysis for the PCB Design Engineer.”
The L2CLKOUTA and L2CLKOUTB signals should not have more than two loads.
Notes: 1. L2CLK outputs are L2CLK_OUTA, L2CLK_OUTB, L2CLK_OUT and L2SYNC_OUT pins. The L2CLK frequency to core fre-
quency settings must be chosen so that the resulting L2CLK frequency and core frequency do not exceed their respective
maximum or minimum operating frequencies. The maximum L2LCK frequency will be system dependent. L2CLK_OUTA
and L2CLK_OUTB must have equal loading.
2. The nominal duty cycle of the L2CLK is 50% measured at midpoint voltage.
3. The DLL re-lock time is specified in terms of L2CLKs. The number in the table must be multiplied by the period of L2CLK to
compute the actual time duration in nanoseconds. Re-lock timing is guaranteed by design and characterization.
4. The L2CR[L2SL] bit should be set for L2CLK frequencies less than 110 MHz. This adds more delay to each tap of the DLL.
5. Allowable skew between L2SYNC_OUT and L2SYNC_IN.
6. This output jitter number represents the maximum delay of one tap forward or one tap back from the current DLL tap as the
phase comparator seeks to minimize the phase difference between L2SYNC_IN and the internal L2CLK. This number must
be comprehended in the L2 timing analysis. The input jitter on SYSCLK affects L2CLKOUT and the L2 address/data/control
signals equally and therefore is already comprehended in the AC timing and does not have to be considered in the L2 timing
analysis.
7. Guaranteed by design and characterization.
Table 13. L2CLK Output AC Timing Specification. At VDD =AVDD = 2.0V 100 mV; -55 ≤Tj≤+125°C, OVDD =3.3V
165 mV and OVDD =1.8V100mVandOV
DD = 2.0V 100 mV
Parameter Symbols
All Speed Grades
UnitMin Max
L2CLK frequency(1)(4) fL2CLK 80 400 MHz
L2CLK cycle time tL2CLK 2.5 12.5 ns
L2CLK duty cycle(2)(7) tCHCL/tL2CLK 50 %
Internal DLL-relock time(3)(7) 640 - L2CLK
DLL capture window(5)(7) 010 ns
L2CLKOUT output-to-output skew(6)(7) tL2CSKW 50 ps
L2CLKOUT output jitter(6)(7) 150 ps

29
PC755B/745B
2138A–HIREL–05/02
The L2CLK_OUT timing diagram is shown in Figure 14.
Figure 14. L2CLK_OUT Output Timing Diagram
L2 Bus Input AC Specifications Table 14 provides the L2 bus interface AC timing specifications for the PC755B as
defined in Figure 15 and Figure 16 for the loading conditions described in Figure 17.
VM = Midpoint Voltage (L2OVdd/2)
L2CLK_OUTA
L2CLK_OUTB
L2 Differential Clock Mode
L2 Single-Ended Clock Mode
L2SYNC_OUT
L2CLK_OUTAVM
tL2CR tL2CF
VM
VM
VM
L2CLK_OUTB
VMVM
VM
VM
VM
L2SYNC_OUT
VM VM VM
VM VM VM
VM
VM
tL2CSKW
tL2CLK
tL2CLK
t
CHCL
t
CHCL
Table 14. L2 Bus Interface AC Timing Specifications at Recommended Operating Conditions
Parameter Symbol
All Speed Grades
UnitMin Max
L2SYNC_IN rise and Fall Time(1) tL2CR &t
L2CF –1.0ns
Setup Times: Data and Parity(2) tDVL2CH 1.2 - ns
Input Hold Times: Data and Parity(2) tDXL2CH 0-ns
Valid Times: (3)(4)
All Outputs when L2CR[14-15] = 00
All Outputs when L2CR[14-15] = 01
All Outputs when L2CR[14-15] = 10
All Outputs when L2CR[14-15] = 11
tL2CHOV -
-
-
-
3.1
3.2
3.3
3.7
ns
Output Hold Times: (3)
All Outputs when L2CR[14-15] = 00
All Outputs when L2CR[14-15] = 01
All Outputs when L2CR[14-15] = 10
All Outputs when L2CR[14-15] = 11
tL2CHOX 0.5
0.7
0.9
1.1
-
-
-
-
ns
L2SYNC_IN to High Impedance:(3)(5)
All Outputs when L2CR[14-15] = 00
All Outputs when L2CR[14-15] = 01
All Outputs when L2CR[14-15] = 10
All Outputs when L2CR[14-15] = 11
tL2CHOZ -
-
-
-
2.4
2.6
2.8
3.0
ns

30 PC755B/745B 2138A–HIREL–05/02

Notes: 1. Rise and fall times for the L2SYNC_IN input are measured from 20% to 80% of L2OVDD.

2. All input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising edge of

the input L2SYNC_IN (see Figure 8). Input timings are measured at the pins.

3. All output specifications are measured from the midpoint voltage of the rising edge of L2SYNC_IN to the midpoint of the sig-

nal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50Ωload (See

Figure 10).

4. The outputs are valid for both single-ended and differential L2CLK modes. For pipelined registered synchronous Bur-

stRAMs, L2CR[14-15] = 01 or 10 is recommended. For pipelined late write synchronous BurstRAMs, L2CR[14-15] = 11 is

recommended.

5. Guaranteed by design and characterization.

6. Revisions prior to Rev 2.8 (Rev E) were limited in performance.and did not conform to this specification. Contact your local

Atmel sales office for more information.

Figure 15 shows the L2 bus input timing diagrams for the PC755B.

Figure 15. L2 Bus Input Timing Diagrams

Figure 16 shows the L2 bus output timing diagrams for the PC755B.

Figure 16. L2 Bus Output Timing Diagrams

Figure 17 provides the AC test load for L2 interface of the PC755B.

Figure 17. AC Test Load for the L2 Interface

L2SYNC_IN

L2 DATA AND DATA

VM = Midpoint Voltage (L2OVDD/2)

tDVL2CH tDXL2CH

tL2CR tL2CF

PARITY INPUTS

L2SYNC_IN

ALL OUTPUT S

VM = Midpoint Voltage (L2OVDD/2)

L2DATA BUS

tL2CHOX

tL2CHOZ

tL2CHOV

OUTPUT L2OVdd/2

RL = 50Ω

Z0 = 50Ω

31
PC755B/745B
2138A–HIREL–05/02
IEEE 1149.1 AC Timing
Specifications
Timing Specifications Table 15 provides the IEEE 1149.1 (JTAG) AC timing specifications as defined in Figure
18, Figure 19, Figure 20, and Figure 21.
Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of TCLK to the midpoint of the signal in ques-
tion. The output timings are measured at the pins. All output timings assume a purely resistive 50Ωload (See Figure 18).
Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
3. Non-JTAG signal input timing with respect to TCK.
4. Non-JTAG signal output timing with respect to TCK.
5. Guaranteed by design and characterization.
Figure 18 provides the AC test load for TDO and the boundary-scan outputs of the
PC755B.
Figure 18. ALTERNATE AC Test Load for the JTAG Interface
Table 15. JTAG AC Timing Specifications (Independent of SYSCLK)(1)
Parameter Symbol Min Max Unit
TCK Frequency of operation fTCLK 016MHz
TCK Cycle time fTCLK 62.5 - ns
TCK Clock pulse width measured at 1.4V tJHJL 31 - ns
TCK Rise and fall times tJR &t
JF 02ns
TRST Assert time(2) tTRST 25 - ns
Input Setup Times:(3)
Boundary-scan data
TMS, TDI tDVJH
tIVJH
4
0-
-
ns
Input Hold Times:(3)
Boundary-scan data
TMS, TDI tDXJH
tIXJH
15
12 -
-
ns
Valid Times:(4)
Boundary-scan data
TDO tJLDV
tJLOV
-
-4
4
ns
Output Hold Times:(4)
Boundary-scan data
TDO tJLDV
tJLOV
25
12 -
-
ns
TCK to output high impedance:(4)(5)
Boundary-scan data
TDO tJLDZ
tJLOZ
3
319
9
ns
OVDD/2
OUTPUT Z0 = 50Ω
RL = 50Ω

32 PC755B/745B 2138A–HIREL–05/02

Figure 19 provides the JTAG clock input timing diagram.

Figure 19. JTAG Clock Input Timing Diagram

Figure 20 provides the TRST timing diagram.

Figure 20. TRST Timing Diagram

Figure 21 provides the boundary-scan timing diagram.

Figure 21. Boundary-Scan Timing Diagram

TCLK VMVMVM

VM = Midpoint Voltage (OVDD/2)

tTCLK

tJR tJF

tJHJL

TRST tTRST

VM = Midpoint Voltage (OVDD/2)

VM VM

TCK

BOUNDARY

DATA OUTPUTS

DATA INPUTS

DATA OUTPUTS

VM = Midpoint Voltage (OVDD/2)

tDXJH

tDVJH

tJLDV

JLDZ

INPUT

DAT A VALID

OUTPUT

tJLDH

DATA

VALID

OUTPUT DATA VALID

PC755B/745B

2138A–HIREL–05/02

Figure 22 provides the test access port timing diagram.

Figure 22. Test Access Port Timing Diagram

JTAG Configuration Signals Boundary scan testing is enabled through the JTAG interface signals. The TRST signal

is optional in the IEEE 1149.1 specification but is provided on all PowerPC implementa-

tions. While it is possible to force the TAP controller to the reset state using only the

TCK and TMS signals, more reliable power-on reset performance will be obtained if the

TRST signal is asserted during power-on reset. Since the JTAG interface is also used

for accessing the common on-chip processor (COP) function of PowerPC processors,

simply tying TRST to HRESET isn’t practical.

The common on-chip processor (COP) function of PowerPC processors allows a remote

computer system (typically a PC with dedicated hardware and debugging software) to

access and control the internal operations of the processor. The COP interface con-

nects primarily through the JTAG port of the processor, with some additional status

monitoring signals. The COP port requires the ability to independently assert HRESET

or TRST in order to fully control the processor. If the target system has independent

reset sources, such as voltage monitors, watchdog timers, power supply failures, or

push-button switches, then the COP reset signals must be merged into these signals

with logic.

The arrangement shown in Figure 23 allows the COP to independently assert HRESET

or TRST, while insuring that the target can drive HRESET as well. The pull-down resis-

tor on TRST ensures that the JTAG scan chain is initialized during power-on if a JTAG

interface cable is not attached; if it is, it is responsible for driving TRST when needed.

TCK

TDI, TMS

TDO

VM = Midpoint Voltage (OVDD/2)

TDO

tIXJH

tIVJH

tJLOV

tJLOZ

INPUT

DATA VALID

OUTPUT

tJLOH

DATA

VALID

OUTPUT DATA VALID

34 PC755B/745B 2138A–HIREL–05/02

Figure 23 shows the suggested TRST connection.

Figure 23. Suggested TRST Connection

The COP header shown in Figure 24 adds many benefits—breakpoints, watchpoints,

are possible through this interface – and can be as inexpensive as an unpopulated foot-

print for a header to be added when needed.

System design information

The COP interface has a standard header for connection to the target system, based on

the 0.025” square-post 0.100” centered header assembly (often called a “Berg” header).

The connector typically has pin 14 removed as a connector key.

Figure 24 shows the COP connector diagram.

Figure 24. COP Connector Diagram

There is no standardized way to number the COP header shown in Figure 24; conse-

quently, many different pin numbers have been observed from emulator vendors. Some

are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-

bottom, while still others number the pins counter clockwise from pin one (as with an IC).

Regardless of the numbering, the signal placement recommended in Figure 24 is com-

montoallknownemulators.

MPC755

HRESET HRESET

TRST

From Target

Board

Sources

COP Header

2 kΩ

QACKQACK

2 kΩ

CKSTP_OUT

13 9 5 1

610 2

TOP VIEW

15 11 7

16 12 8 4

KEY

No pin

HRESET

SRESET

TMS

RUN/STOP

TCK

TDI

TDO

Ground

TRST

VDD_SENSE

Pins 10, 12 and 14 are no-con nec ts.

Pin 14 is not physically present

QACK

CHKSTP_IN

PC755B/745B

2138A–HIREL–05/02

The QACK signal shown in Table 15 is usually hooked up to the PCI bridge chip in a

system and is an input to the PC755B informing it that it can go into the quiescent state.

Under normal operation this occurs during a low power mode selection. In order for

COP to work the PC755B must see this signal asserted (pulled down). While shown on

the COP header, not all emulator products drive this signal. To preserve correct power

down operation, QACK should be merged so that it also can be driven by the PCI

bridge.

Table 16 shows the pin definitions.

Table 16. COP Pin Definitions

Pins Signal Connection Special Notes

1TDO TDO

2QACK QACK ADD 2K pull-down to ground. Must be merged with on-board QACK,ifany.

3TDI TDI

4TRST TRST ADD 2K pull-down to ground. Must be merged with on-board QACK,ifany.

SeeFigure23.

5 RUN/STOP No connect Used on 604e; leave no-connect for all other processors.

6 VDD_SENSE VDD ADD 2K pull-up to OVDD (for short circuit limiting protection only).

7TCK TCK

8 CKSTP_IN CKSTP_IN Optional. ADD 10K pull-up to OVDD. Used on several emulator products. Useful for

checkstopping the processor from a logic analyzer of other external trigger.

9TMS TMS

10 N/A

11 SRESET SRESET Mergewithon-board SRESET, if any.

12 N/A

13 HRESET HRESET Mergewithon-board HRESET

14 N/A Key location; pin should be removed.

15 CKSTP_OUT CKSTP_OUT ADD 10K pull-up to OVDD.

16 Ground Digital Ground

36 PC755B/745B 2138A–HIREL–05/02

Preparation for Delivery

Packaging Microcircuits are prepared for delivery in accordance with MIL-PRF-38535.

Certificate of Compliance Atmel offers a certificate of compliances with each shipment of parts, affirming the prod-

ucts are in compliance either with MIL-PRF-883 and guarantying the parameters not

tested at temperature extremes for the entire temperature range.

Handling MOS devices must be handled with certain precautions to avoid damage due to accu-

mulation of static charge. Input protection devices have been designed in the chip to

minimize the effect of static buildup. However, the following handling practices are

recommended:

1. Devices should be handled on benches with conductive and grounded surfaces.

2. Ground test equipment, tools and operator.

3. Do not handle devices by the leads.

4. Store devices in conductive foam or carriers.

5. Avoid use of plastic, rubber, or silk in MOS areas.

6. Maintain relative humidity above 50 percent if practical.

7. For CI-CGA packages, use specific tray to take care of the highest height of the

package compared with the normal CBGA.

Package Mechanical

Data The following sections provide the package parameters and mechanical dimensions for

the PC745B, 255 PBGA package as well as the PC755B, 360 CBGA and PBGA pack-

ages. While both the PC755B plastic and the ceramic packages are described here,

both packages are not guaranteed to be available at the same time. All new designs

should allow for either ceramic or plastic BGA packages for this device. For more infor-

mation on designing a common footprint for both plastic and ceramic package types,

please contact your local Motorola sales office.

Parameters for the

PC745B

Package Parameters for the

PC745B PBGA The package parameters are as provided in the following list. The package type is

21 x 21 mm, 255-lead plastic ball grid array (PBGA).

Mechanical Dimensions of the

PC745B PBGA Package Figure 25 provides the mechanical dimensions and bottom surface nomenclature of the

PC745B, 255 PBGA package.

Package outline 21 x 21 mm

Interconnects 255 (16 x 16 ball array – 1)

Pitch 1.27 mm (50 mil)

Minimum module height 2.25 mm

Maximum module height 2.80 mm

Ball diameter (typical) 0.75 mm (29.5 mil)

PC755B/745B

2138A–HIREL–05/02

Figure 25. Mechanical Dimensions and Bottom Surface Nomenclature of the PC745B PBGA

Parameters for the PC755B

PBGA

Package Parameter for the

PC755B PBGA The package parameters are as provided in the following list. The package type is 25 x

25 mm, 360-lead plastic ball grid array (PBGA).

Package outline 25 x 25 mm

Interconnects 360 (19 x 19 ball array – 1)

Pitch 1.27 mm (50 mil)

Minimum module height 2.22 mm

Maximum module height 2.77 mm

Ball diameter 0.75 mm (29.5 mil)

NOTES:

1. DIMENSIONING AND TOLERANCING

PER ASME Y14.5M, 1994.

2. DIMENSION S IN MILLIMETERS.

3. TOP SIDE A1 CORNER INDEX IS A

METALIZED FEATURE WITH VARIOUS

SHAPES. BOTTOM SIDE A1 CORNER IS

DESIGNATED WITH A BALL MISSING

FROM THE ARRAY.

4. CAPACITO R PADS MAY BE

UNPOPULATED.

Table 1

Millimeters

DIM Min Max

A2.25 2.80

A1 0.50 0.70

A2 1.00 1.20

b0.60 0.90

D21.00 BSC

E21.00 BSC

e1.27 BSC

0.2

A1 CORNER

0.2

AA1

0.2 C

255X

12345678910111213141516

A0.3C

0.15

38 PC755B/745B 2138A–HIREL–05/02

Mechanical Dimensions of the

PC755B PBGA Figure 26 provides the mechanical dimensions and bottom surface nomenclature of the

PC755B, 360 PBGA package.

Figure 26. Mechanical Dimensions and Bottom Surface Nomenclature of the PC755B PBGA

NOTES:

A. DIMENSIONING AND T OLERANCING PER

ASME Y14.5M, 1994.

B. DIMENSIONS IN MILLIMETERS.

C. TOP SIDE A1 CORNER INDEX IS A

METALIZED FEA TURE WITH VARIOUS

SHAPES. BOTT OM SIDE A1 CORNER IS

DESIGNATED WITH A BALL MISSING

FROM THE ARRA Y.

0.2

360X

A1 CORNER

0.2

12345678910111213141516

A0.3

0.15

AA1

0.2 C

171819

Millimeters

DIM Min Max

A2.22 2.77

A1 0.50 0.70

A2 1.00 1.20

b0.60 0.90

D25.00 BSC

E25.00 BSC

e1.27 BSC

PC755B/745B

2138A–HIREL–05/02

Mechanical Dimensions of the

PC755B CBGA Package Figure 27 provides the mechanical dimensions and bottom surface nomenclature of the

PC755B, 360 CBGA package.

Figure 27. Mechanical Dimensions and Bottom Surface Nomenclature of PC755B (CBGA)

NOTES:

A. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

B. DIMENSIONS IN MILLIMETERS.

C. TOP SIDE A1 CORNER INDEX IS A

METALIZED FEATURE WITH VARIOUS

SHAPES. BOTTOM SIDE A1 CORNER IS

DESIGNATED WITH A BALL MISSING

FROM THE ARRA

D. TOP SIDE CAPACITOR ASSEMBLY AREAS

ARE CONNECTED TO POWER PLANES

BUT NOT USED

360X

1 2 3 4 5 6 7 8 910 11 121314 15 16

E0.3

0.15

0.2 T

171819

DIM MIN MAX

MAX

MIN

MILLIMETERS INCHES

25.000 BSC

2.65 3.2 0.104 0.126

0.820 0.930 0.032

7.73

6.61

0.0390.0310.990

0.790

1.270 BSC 0.050 BSC

0.635 BSC 0.025 BSC

A1 1.1 1.3

0.2

A1 CORNER

0.2

0.984 BSC

0.043 0.052

0.984 BSC

0.037

2.75

0.108

0.118

40 PC755B/745B 2138A–HIREL–05/02

Mechanical Dimensions of the

PC755B CI-CGA Package Figure 28 provides the mechanical dimensions and bottom surface nomenclature of

PC755B, 360 CI-CGA package

Figure 28. Mechanical Dimensions and Bottom Surface Nomenclature of PC755B (CI-CGA)

NOTES:

A. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

B. DIMENSIONS IN MILLIMETERS.

C. TOP SIDE A1 CORNER INDEX IS A

METALIZED FEATURE WITH VARIOUS

SHAPES. BOTTOM SIDE A1 CORNER IS

DESIGNATED WITH A BALL MISSING

FROM THE ARRA

D. TOP SIDE CAPACITOR ASSEMBLY AREAS

ARE CONNECTED TO POWER PLANES

BUT NOT USED

360X

1 2 3 4 5 6 7 8 910 11 121314 15 16

E0.3

0.15

171819

DIM MAX

MIN

MILLIMETERS

25.000 BSC

C4.04 BSC

0.790 0.990

7.73

6.61

1.6951.545

V0.35

0.25

D3 2.75

E3 3

1.270 BSC

0.635 BSC

0.2

A1 CORNER

0.2

3.22 BSC

0.10 BSC

-T-

0.150 T

PC755B/745B

2138A–HIREL–05/02

Clock Relationship

Choices The PC755B’s PLL is configured by the PLL_CFG[0-3] signals. For a given SYSCLK

(bus) frequency, the PLL configuration signals set the internal CPU and VCO frequency

of operation. The PLL configuration for the PC755B is shown in Figure 30 for example

frequencies.

Notes: 1. PLL_CFG[0:3] settings not listed are reserved.

2. The sample bus-to-core frequencies shown are for reference only. Some PLL configurations may select bus, core, or VCO

frequencies which are not useful, not supported, or not tested for by the PC755B; see Section «Clock AC Specifications»

page 24 for valid SYSCLK, core, and VCO frequencies.

3. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly, the PLL is disabled, and the bus mode

is set for 1:1 mode operation. This mode is intended for factory use and emulator tool use only.

Note: The AC timing specifications given in this document do not apply in PLL-bypass mode.

4. In PLL off mode, no clocking occurs inside the PC755 regardless of the SYSCLK input.

Table 17. PC755B Microprocessor PLL Configuration

PLL_CFG [0-3]

Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz)

Bus-to-Core

Multiplier Core-toVCO

Multiplier Bus 33

MHz Bus 50

MHz Bus 66

MHz Bus 75

MHz Bus 80

MHz Bus 100

MHz

0100 2x 2x -----

200

(400)

1000 3x 2x - - 200

(400) 225

(450) 240

(480) 300

(600)

1110 3.5x 2x - - 233

(466) 263

(525) 280

(560) 350

(700)

1010 4x 2x - 200

(400) 266

(533) 300

(600) 320

(640) 400

(800)

0111 4.5x 2x - 225

(450) 300

(600) 338

(675) 360

(720) -

1011 5x 2x - 250

(500) 333

(666) 375

(750) 400

(800) -

1001 5.5x 2x - 275

(550) 366

5733°---

1101 6x 2x 200

(400) 300

(600) 400

(800) ---

0101 6.5x 2x 216

(433) 325

(650) ----

0010 7x 2x 233

(466) 350

(700) ----

0001 7.5x 2x 250

(500) 375

(750) ----

1100 8x 2x 266

(533) 400

(800) ----

0110 10x 2x 333

(666) -----

0011 PLL off/bypass PLL off, SYSCLK clocks core circuitry directly, 1x bus-to-core implied

1111 PLL off PLL off, no core clocking occurs

42 PC755B/745B 2138A–HIREL–05/02

The PC755B generates the clock for the external L2 synchronous data SRAMs by divid-

ing the core clock frequency of the PC755B. The divided-down clock is then phase-

adjusted by an on-chip delay-lock-loop (DLL) circuit and should be routed from the

PC755B to the external RAMs. A separate clock output, L2SYNC_OUT is sent out half

the distance to the SRAMs and then returned as an input to the DLL on pin L2SYNC_IN

so that the rising-edge of the clock as seen at the external RAMs can be aligned to the

clocking of the internal latches in the L2 bus interface.

The core-to-L2 frequency divisor for the L2 PLL is selected through the L2CLK bits of

the L2CR register. Generally, the divisor must be chosen according to the frequency

supported by the external RAMs, the frequency of the PC755B core, and the phase

adjustment range that the L2 DLL supports. Figure 18 shows various example L2 clock

frequencies that can be obtained for a given set of core frequencies. The minimum L2

frequency target is 80 MHz.

Note: The core and L2 frequencies are for reference only. Some examples may repre-

sent core or L2 frequencies which are not useful, not supported, or not tested

for by the PC755B; see Section “L2 Clock AC Specifications”page 27 for valid

L2CLK frequencies. The L2CR[L2SL] bit should be set for L2CLK frequencies

less than 110 MHz.

System Design

Information

PLL Power Supply Filtering The AVDD and L2AVDD power signals are provided on the PC755B to provide power to

the clock generation phase-locked loop and L2 cache delay-locked loop respectively. To

ensure stability of the internal clock, the power supplied to the AVDD input signal should

be filtered of any noise in the 500 kHz to 10 MHz resonant frequency range of the PLL.

A circuit similar to the one shown in Figure 30 using surface mount capacitors with mini-

mum Effective Series Inductance (ESL) is recommended. Consistent with the

recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of

Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recom-

mended over a single large value capacitor.

Table 18. Sample Core-to-L2 Frequencies

Core Frequency in MHz 1 1.5 2 2.5 3

250 250 166 125 100 83

266 266 177 133 106 89

275 275 183 138 110 92

300 300 200 150 120 100

325 325 217 163 130 108

333 333 222 167 133 111

350 350 233 175 140 117

366 366 244 183 146 122

375 375 250 188 150 125

400 400 266 200 160 133

PC755B/745B

2138A–HIREL–05/02

The circuit should be placed as close as possible to the AVDD pin to minimize noise cou-

pled from nearby circuits. An identical but separate circuit should be placed as close as

possible to the L2AVDD pin. It is often possible to route directly from the capacitors to the

AVDD pin, which is on the periphery of the 360 BGA footprint, without the inductance of

vias. The L2AVDD pin may be more difficult to route but is proportionately less critical.

Figure 29. PLL Power Supply Filter Circuit

Power Supply Voltage

Sequencing The notes in Figure 31 contain cautions about the sequencing of the external bus volt-

ages and core voltage of the PC755B (when they are different). These cautions are

necessary for the long term reliability of the part. If they are violated, the ESD (Electro-

static Discharge) protection diodes will be forward biased and excessive current can

flow through these diodes. If the system power supply design does not control the volt-

age sequencing, the circuit of Figure 31 can be added to meet these requirements. The

MUR420 Schottky diodes of Figure 31 control the maximum potential difference

between the external bus and core power supplies on power-up and the 1N5820 diodes

regulate the maximum potential difference on power-down.

Figure 30. Example Voltage Sequencing Circuit

Decoupling

Recommendations Due to the PC755B’s dynamic power management feature, large address and data

buses, and high operating frequencies, the PC755B can generate transient power

surges and high frequency noise in its power supply, especially while driving large

capacitive loads. This noise must be prevented from reaching other components in the

PC755B system, and the PC755B itself requires a clean, tightly regulated source of

power. Therefore, it is recommended that the system designer place at least one decou-

pling capacitor at each VDD,OVDD, and L2OVDD pin of the PC755B. It is also

recommended that these decoupling capacitors receive their power from separate VDD,

(L2)OVDD and GND power planes in the PCB, utilizing short traces to minimize

inductance.

These capacitors should have a value of 0.01 ∝For0.1∝F. Only ceramic SMT (surface

mount technology) capacitors should be used to minimize lead inductance, preferably

0508 or 0603 orientations where connections are made along the length of the part.

VDD AVDD (or L2AVDD)

10 Ω

2.2 µF 2.2 µF

GND

Low ESL Surface Mount Capacitors

3.3V 2.0V

MURS320

1N5820

MURS320

1N5820

44 PC755B/745B 2138A–HIREL–05/02

In addition, it is recommended that there be several bulk storage capacitors distributed

around the PCB, feeding the VDD,L2OVDD, and OV vplanes, to enable quick recharging

of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent

series resistance) rating to ensure the quick response time necessary. They should also

be connected to the power and ground planes through two vias to minimize inductance.

Suggested bulk capacitors –100-330 ∝F (AVX TPS tantalum or Sanyo OSCON).

Connection

Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an

appropriate signal level through a resistor. Unused active low inputs should be tied to

OVDD. Unused active high inputs should be connected to GND. All NC (no-connect) sig-

nals must remain unconnected.

Power and ground connections must be made to all external VDD,OVDD, L2OVDD,and

GND pins of the PC755B.

Output Buffer DC Impedance The PC755B 60x and L2 I/O drivers are characterized over process, voltage, and tem-

perature. To measure Z0, an external resistor is connected from the chip pad to

(L2)OVDD or GND. Then, the value of each resistor is varied until the pad voltage is

(L2)OVDD/2 (See Figure 32).

The output impedance is the average of two components, the resistances of the pull-up

and pull-down devices. When Data is held low, SW2 is closed (SW1 is open), and RNis

trimmed until the voltage at the pad equals (L2)OVDD/2. RNthen becomes the resistance

of the pull-down devices. When Data is held high, SW1 is closed (SW2 is open), and RP

is trimmed until the voltage at the pad equals (L2)OVDD/2. RPthen becomes the resis-

tance of the pull-up devices.

NO TAG describes the driver impedance measurement circuit described above.

Figure 31. Driver Impedance Measurement Circuit

(L2)OVDD

OGND

Pad

Data

SW1

SW2

(L2)OVDD

PC755B/745B

2138A–HIREL–05/02

Alternately, the following is another method to determine the output impedance of the

PC755B. A voltage source, Vforce, is connected to the output of the PC755B as in Figure

32. Data is held low, the voltage source is set to a value that is equal to (L2)OVDD/2 and

the current sourced by Vforce is measured. The voltage drop across the pull-down

device, which is equal to (L2)OVDD/2, is divided by the measured current to determine

the output impedance of the pull-down device, RN. Similarly, the impedance of the pull-

up device is determined by dividing the voltage drop of the pull-up, (L2)OVDD/2, by the

current sank by the pull-up when the data is high and Vforce is equal to (L2)OVDD/2. This

methodcanbeemployedwitheitherempiricaldatafromatestsetuporwithdatafrom

simulation models, such as IBIS.

RPand RNare designed to be close to each other in value. Then Z0=(R

P+R

N)/2.

Figure 32 describes the alternate driver impedance measurement circuit.

Figure 32. Alternate Driver Impedance Measurement Circuit

Table 19 summarizes the signal impedance results. The driver impedance values were

characterized at 0°C, 65°C, and 105°C. The impedance increases with junction temper-

ature and is relatively unaffected by bus voltage.

Pull–up Resistor

Requirements The PC755B requires high-resistive (weak: 10 KΩ) pull-up resistors on several control

pins of the bus interface to maintain the control signals in the negated state after they

have been actively negated and released by the PC755B or other bus masters. These

pins are TS,ABB, ARTRY.

Three test pins also require pull-up resistors (weak or stronger: 4.7 kΩ -10kΩ). These

pins are L1_TSTCLK, L2_TSTCLK, and LSSD_MODE. These signals are for factory

use only and must be pulled up to OVDD for normal machine operation.

In addition, the PC755B has one open-drain style output that requires a pull-up resistor

(weak or stronger: 4.7 KW-10 KW) if it is used by the system. This pin is CKSTP_OUT.

Table 19. Impedance Characteristics

VDD =2.0V,OV

DD =3.3V,T

c=0-105°C

Impedance Processor bus L2 bus Symbol Unit

RN 25-36 25-36 Z0W

RP 26-39 26-39 Z0W

(L2)OVDD

BGA

Data Pin

OGND

Vforce

46 PC755B/745B 2138A–HIREL–05/02

During inactive periods on the bus, the address and transfer attributes may not be

driven by any master and may therefore float in the high-impedance state for relatively

long periods of time. Since the PC755B must continually monitor these signals for

snooping, this float condition may cause excessive power draw by the input receivers on

the PC755B or by other receivers in the system. It is recommended that these signals

be pulled up through weak (i.e. 10 KΩ ) pull-up resistors by the system, or that they may

be otherwise driven by the system during inactive periods of the bus. The snooped

address and transfer attribute inputs are:

A[0:31], AP[0:3], TT[0:4], TBST and GBL.

The data bus input receivers are normally turned off when no read operation is in

progress and therefore do not require pull-up resistors on the bus. Other data bus

receivers in the system, however, may require pull-ups, or that those signals be other-

wise driven by the system during inactive periods by the system. The data bus signals

are: DH[0:31], DL[0:31] and DP[0:7]

If 32-bit data bus mode is selected, the input receivers of the unused data and parity bits

will be disabled, and their outputs will drive logic zeros when they would otherwise nor-

mally be driven. For this mode, these pins do not require pull-up resistors, and should be

left unconnected by the system to minimize possible output switching.

If address or data parity is not used by the system, and the respective parity checking is

disabled through HID0, the input receivers for those pins are disabled, and those pins

do not require pull-up resistors and should be left unconnected by the system. If all par-

ity generation is disabled through HID0, then all parity checking should also be disabled

through HID0, and all parity pins may be left unconnected by the system.

The L2 interface does not normally require pull-up resistors.

Definitions

Datasheet Status Validity

Objective specification This datasheet contains target and goal specification for

discussion with customer and application validation. Before design phase.

Target specification This datasheet contains target or goal specification for

product development. Valid during the design phase.

Preliminary specification ∝site This datasheet contains preliminary data. Additional data

may be published later; could include simulation result. Valid before characterization phase.

Preliminary specification βsite This datasheet contains also characterization results. Valid before the industrialization

phase.

Product specification This datasheet contains final product specification. Valid for production purpose.

Limiting Values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the

limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at

any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values

for extended periods may affect device reliability.

Application Information

Where application information is given, it is advisory and does not form part of the specification.

PC755B/745B

2138A–HIREL–05/02

Life Support

Applications These products are not designed for use in life support appliances, devices, or systems

where malfunction of these products can reasonably be expected to result in personal

injury. Atmel customers using or selling these products for use in such applications do

so at their own risk and agree to fully indemnity Atmel for any damages resulting from

such improper use or sale.

Differences with

Commercial Part

Ordering Information

Note: For availability of different versions, contact your Atmel sales office.

Commercial part Military part

Temperature range Tj= 0 to 105°CT

j=-55°Cto 125°C

PC755B M ZF U 300 L x

Type

Package:

ZF: FC-PBGA

G: CBGA

GS: CI-CGA Screening Level(1)

U: Upscreening Test

Revision Level(1)

E: Rev. 2.8

Temperature Range: Tj

M: -55 C, +125 C

V: -40 C, +110 C

Bus divider

(to be confirmed)

L: Any valid PLL configuration

Max internal processor speed

300: 300 MHz

350: 350 MHz

366: 366 MHz

400: 400 MHz, TBC

Printed on recycled paper.

Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty

which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors

which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does

not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted

by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical

components in life support devices or systems.

Atmel Headquarters Atmel Operations

Corporate Headquarters

2325 Orchard Parkway

San Jose, CA 95131

TEL 1(408) 441-0311

FAX 1(408) 487-2600

Europe

Atmel Sarl

Route des Arsenaux 41

Case Postale 80

CH-1705 Fribourg

Switzerland

TEL (41) 26-426-5555

FAX (41) 26-426-5500

Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimhatsui

East Kowloon

Hong Kong

TEL (852) 2721-9778

FAX (852) 2722-1369

Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

TEL (81) 3-3523-3551

FAX (81) 3-3523-7581

Memory

2325 Orchard Parkway

San Jose, CA 95131

TEL 1(408) 441-0311

FAX 1(408) 436-4314

Microcontrollers

2325 Orchard Parkway

San Jose, CA 95131

TEL 1(408) 441-0311

FAX 1(408) 436-4314

La Chantrerie

BP 70602

44306 Nantes Cedex 3, France

TEL (33) 2-40-18-18-18

FAX (33) 2-40-18-19-60

ASIC/ASSP/Smart Cards

Zone Industrielle

13106 Rousset Cedex, France

TEL (33) 4-42-53-60-00

FAX (33) 4-42-53-60-01

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906

TEL 1(719) 576-3300

FAX 1(719) 540-1759

Scottish Enterprise Technology Park

Maxwell Building

East Kilbride G75 0QR, Scotland

TEL (44) 1355-803-000

FAX (44) 1355-242-743

RF/Automotive

Theresienstrasse 2

Postfach 3535

74025 Heilbronn, Germany

TEL (49) 71-31-67-0

FAX (49) 71-31-67-2340

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906

TEL 1(719) 576-3300

FAX 1(719) 540-1759

Biometrics/Imaging/Hi-Rel MPU/

High Speed Converters/RF Datacom

Avenue de Rochepleine

BP 123

38521 Saint-Egreve Cedex, France

TEL (33) 4-76-58-30-00

FAX (33) 4-76-58-34-80

e-mail

literature@atmel.com

Web Site

http://www.atmel.com

2138A–HIREL–05/02 0M

ATMEL®is the registered trademark of Atmel.

The PowerPC names and the PowerPC logotype are trademarks of International Business Machines Corpora-

tion, used under license therform.

Motorola is the registered trademark of Motorola, Inc.

AltiVec™is a trademark of Motorola, Inc.

Other terms and product names may be the trademarks of others.