LM1290 Autosync Horizontal Deflection Processor General Description Features The LM1290 is a high-performance, low-cost deflection solution for autosync monitors. n Full autosync -- 22 kHz to 110 kHz with no component switching or external adjustments n No manufacturing trims needed -- internal VCO capacitor trimmed on chip n Sample-and-hold circuit for fast top-of-screen phase recovery, even when using composite sync n DC-controlled H phase and duty cycle n Resistor-programmable minimum VCO frequency n Excellent jitter performance n X-ray input disables H drive until VCC powered down n Low VCC disables H drive (VCC < 8.5V) n H output transistor protected against accidental turn on during flyback n Capacitor-programmable frequency ramping, dfVCO / dt, protects H output transistor during scanning mode changes The LM1290 provides full autosync capability, DC controls and complete freedom from manufacturing trims. Its continuous capture range is from 22 kHz to 110 kHz (1:5). Mode change frequency ramping, for protection of the horizontal deflection output transistor, is programmable by using an external capacitor. Together with the National Semiconductor LM1296 Raster Geometry Correction System for Multi-Frequency Displays, excellent performance is offered. The two-chip solution provides the advantage of good jitter performance, simplified board layout, and lower system cost. The LM1290 is packaged in a 14-pin plastic DIP package. Connection Diagram DS012917-1 FIGURE 1. Order Number LM1290N See NS Package Number N14A (c) 1999 National Semiconductor Corporation DS012917 www.national.com LM1290 Autosync Horizontal Deflection Processor January 1997 Absolute Maximum Ratings (Notes 1, 3) Thermal Resistance (JA) Junction Temperature (TJ) ESD Susceptibility (Note 5) Storage Temperature Lead Temperature (Soldering 10 seconds) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Input Voltage (VDC) Pin 1 Pins 3, 4, 5, 6 Pin 10 Pin 12 Output Sink Current, Pin 7 Power Dissipation (PD) (Above 25C, derate based on JA and TJ) 15V 8V VCC 1.0V < VDC < 7.5V 10V 130 mA 75C/W 150C 3.5 kV -65C to +150C 265C Operating Ratings (Note 2) Operating Temperature Range Supply Voltage -20C to +80C 10.8V VCC 13.2V 1.65W Electrical Characteristics See Test Circuit (Figure 2) ; TA = 25C; VCC = 12V; V5 = 0V unless otherwise stated. Parameter Condition Typical Limit (Note 6) (Note 7) Units 30 40 mA (max) Supply Current (Pin 14) Pin 3 and Pin 7 Open Circuit, Pin 1 = -100 A Minimum Capture Frequency H Sync Duty Cycle = 10%; 10 22 kHz (max) Maximum Capture Frequency Pin 1 (fMIN) Open 115 110 kHz (min) H/HV SYNC Input (Pin 3) High Level 2.2 V (min) Threshold Voltage Low Level 0.8 V (max) 24 % H/HV SYNC Input (Pin 3) 26 Maximum Sync Tip Duty Cycle H/HV SYNC Input (Pin 3) fH = 22 kHz % 5 Minimum Sync Tip Duty Cycle H/HV POLARITY (Pin 2) CPOL = 0.1 F; IOL = +1 A 0.05 0.4 V (max) CPOL = 0.1 F; IOL = -1 A 4.5 4 V (min) Low Level Output Voltage, VOL H/HV POLARITY (Pin 2) High Level Output Voltage, VOH FVC Gain 22 kHz f 0.055 V/kHz VCO Gain 22 kHz fVCO 110 kHz H Sync Duty Cycle = 10%: 18.2 kHz/V fH = 110 kHz fH = 60 kHz fH = 22 kHz 120 Phase Detector 1 Gain H 110 kHz A/radian 80 30 Phase Detector 1 Output Impedance 20 k (Pin 12) Phase Detector 1 Leakage Current + H/HV SYNC Input Grounded 0.3 2 A VCO Bias Current (Pin 12) Jitter Free Run Frequency Variation H Drive Phase Control Gain www.national.com fH = 110 kHz (Note 8) fH = 90 kHz fH = 60 kHz fH = 31 kHz fH = 22 kHz I1 = -225 A 0.9 1.1 1.6 ns p-p 3.6 5.8 V10 = 2V to 6V (Note 11) 2 32 34 kHz (max) 26 25 kHz (min) 8.89 % TH/V (32) (/V) Electrical Characteristics (Continued) See Test Circuit (Figure 2) ; TA = 25C; VCC = 12V; V5 = 0V unless otherwise stated. Parameter Condition Typical Limit (Note 6) (Note 7) H Drive Phase Control Range V10 = 3.6V to 7V (Notes 9, 11) 14 H Drive Duty Cycle Control Gain (See Application Hint #3) V4 = 0V to 4V (Note 10) V4 = 0V (Note 10) 10.8 H Drive Duty Cycle Maximum (Pin 7) Units %TH %/V 68 63 % (min) 25 35 % (max) H Drive Low Level Output Voltage (Pin 7) V4 = 4V (Note 10) IOL = 100 mA 0.7 V Flyback Input Threshold Voltage (Pin 6) Positive-Going Flyback Pulse 2.2 V Maximum Allowable Storage Delay of From H Drive Rising Edge to Horizontal Deflection Output Transistor Center of Flyback Pulse 30 %TH H Drive Duty Cycle Minimum (Pin 7) Plus Half of Flyback Pulse Width VCC Lockout Threshold Voltage VCC Below Threshold: (Pin 14) H Drive Output Disabled VCC Above Threshold: 8.5 V (max) 10.5 V (min) 2 V (min) H Drive Output Enabled X-Ray Shutdown Threshold Voltage Above Threshold: (Pin 5) H Drive Output Disabled 1.85 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 2: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 3: All voltages are measured with respect to GND, unless otherwise specified. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA and the ambient temperature, TA. The maximum allowable power dissipation at any elevated temperature is PD = (TJMAX - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. For this device, TJMAX = 150C. The typical thermal resistance (JA) of the LM1290N is 75C/W. Note 5: Human Body model, 100 pF capacitor discharged through a 1.5 k resistor. Note 6: Typical specifications are at TA = 25C and represent most likely parametric norm. Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: The standard deviation, , of the flyback pulse period is measured with a HP 53310A Modulation Domain Analyzer. Peak-to-peak jitter of the flyback pulse is defined by 6. Note 9: A positive phase value represents a phase lead of the flyback pulse peak with reference to the center of H sync. Note 10: The duty cycle is measured under the conditions of free run with I1 = -100 A, TFBP = 3 s and Td = 3.5 s where TFBP and Td are the flyback pulse width and the turn off delay of the H deflection output transistor respectively. Note 11: TH is defined as the total time of one horizontal line. 3 www.national.com Test Circuit DS012917-2 FIGURE 2. System Block Diagram DS012917-3 FIGURE 3. www.national.com 4 DRIVE output (pin 7) is latched high. VCC has to be reduced to below approximately 2V to clear the latched condition, i.e., power must be turned off. See Figure 7 for the input schematic. Pin 6 -- FLYBACK: Input pin for phase detector 2. For best operation, the flyback peak should be at least 5V but not greater than VCC. Any pulse width greater than 1.5 s is acceptable. See Figure 8 for the input schematic. Pin 7 -- H DRIVE: This is an open-collector output which provides the drive pulse for the high power deflection circuit. The pulse duty cycle is controlled by pin 4. Polarity convention: Horizontal deflection output transistor is on when H DRIVE OUT is low. See Figure 9 for the output schematic. Pin 8 -- GND: System ground. For best jitter performance, all bypass capacitors should be connected to this pin via short paths. Pin 9 -- PD2 FILTER: The low-pass filter cap of between 0.01 F to 1 F for the output of phase detector 2 is connected from this pin to pin 8 (GND) via a short path. A smaller value increases the response. Pin 10 -- PHASE: A DC control voltage applied to this pin sets the phase of the flyback pulse with respect to the center of H sync. See Figure 10 for the input schematic. Pin 11 -- FVC FILTER: A 1 F capacitor is connected from this pin to pin 8 (GND) via a short path. Pin 12 -- PD1 OUT/VCO IN: Phase detector 1 has a gated charge pump output which requires an external low-pass filter. For best jitter performance, the filter should be grounded to pin 8 (GND) via a short path. If a voltage source is applied to this pin, the phase detector is disabled and the VCO can be controlled directly. Pin 13 -- VREF: This is the decoupling pin for the internal 8.2V reference. It should be decoupled to pin 8 (GND) via a short path with a cap of at least 470 F. Do not load this pin. Pin 14 -- VCC: 12V nominal power supply pin. This pin should be decoupled to pin 8 (GND) via a short path with a cap of at least 47 F. Pin Descriptions See Figure 4 through Figure 10 for input and output schematics. Pin 1 -- fMIN: A resistor from this pin to ground sets the free run frequency of the LM1290. The free run frequency should be set typically as: fMIN = 0.85(fMINLOCK) - 2 kHz where fMINLOCK is the minimum lock frequency required for the application. The resistance required to set this frequency is approximately: For example, to find RMIN for VGA which has fMINLOCK = 31.469 kHz, fMIN = 0.85(31.469 kHz) - 2 kHz = 24749 Rounding to the closest standard 1% resistor gives RMIN = 21.5 k. Pin 2 -- H/HV POLARITY: A 0.1 F capacitor is connected from this pin to ground for detecting the polarity of H/HV sync at pin 3. A low logic level at pin 2 indicates active-high H/HV sync to pin 3, a high level indicates active-low. See Figure 4 for the output schematic. Pin 3 -- H/HV SYNC: This input pin accepts DC-coupled H or composite sync of either polarity. For best noise immunity, a resistor of 2 k or less should be connected from this pin to pin 8 (GND) via a short path. See Figure 5 for the input schematic. Pin 4 -- DUTY CYCLE: A DC voltage applied to this pin sets the duty cycle of the H DRIVE output (pin 7), with a range of approximately 30% to 70%. 2V sets the duty cycle to approximately 50%. See Figure 6 for the input schematic. Pin 5 -- X-RAY: This pin is for monitoring CRT anode voltage. If the input voltage exceeds an internal threshold, H Input/Output Schematics DS012917-5 DS012917-4 FIGURE 5. FIGURE 4. 5 www.national.com Input/Output Schematics (Continued) DS012917-6 FIGURE 6. DS012917-9 FIGURE 9. DS012917-7 FIGURE 7. DS012917-10 FIGURE 10. DS012917-8 FIGURE 8. www.national.com 6 Consider a scanning mode transition at t = 0 from f1 to f2. The VCO frequency as a function of time, fVCO(t), is described by the equation, Application Hints 1. Phase Control for Geometry Correction: Pin 10 (PHASE) is designed to control static phase (picture horizontal position) as well as dynamic phase for geometry correction. Complete control of static and dynamic phase can be achieved by superposing a correction waveform (Sawtooth and/or parabola) on the DC control voltage at pin 10 (see Figure 12). 2. Programmable Frequency Ramping: H frequency transitions from high to low present a special problem for deflection output stages without current limiting. If, during such a transition, the output transistor on-time increases excessively before the B+ voltage has decreased to its final level, then the deflection inductor current ramps too high and the induced flyback pulse can exceed the breakdown voltage, BVCEX, of the output transistor. To prevent this, the rate of change of the VCO frequency must be limited. fVCO(t) f 1 + (f 2 - f 1) (1 - exp (-t /)), where = 40 x 103 x CFVC. The above equation can be used to predict VCO behavior during frequency transitions, but in practice the value of CFVC is most easily determined empirically. In general, large values minimize the chance of exceeding BVCEX, but generate long PLL capture times. 3. Phase Voltage Range vs Delay Time: The recommended phase voltage range to use on pin 10 (PHASE) depends on the delay time of the deflection output stage. Delay time is defined as the time from the rising edge of H Drive to the center of flyback. For best performance the phase voltage range should be in the unshaded area of Figure 11. Recommended Phase Voltage for 640 x 480 @ 60 Hz DS012917-11 FIGURE 11. 7 www.national.com Typical Application DS012917-12 *Actual value depends on the application and the ambient noise level inside the monitor. FIGURE 12. www.national.com 8 LM1290 Autosync Horizontal Deflection Processor Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM1290N NS Package Number N14A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.