www.vishay.com For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 20038
1Revision: 02-Sep-08
D.. AP
Vishay
Thick Film, Rectangular Chip Resistors
for Conductive Gluing
FEATURES
•AgPd-Terminations for conductive gluing
•Protective overglaze
•Metal glaze on high quality ceramic
•Compliant with “Restriction of the use of Hazardous
Substances” (RoHS) directive 2002/95/EC (issue 2004)
•Excellent stability (ΔR/R ≤ 1 % for 1000 h at 70 °C)
Notes
•These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional time.
•Marking and packaging: See appropriate catalog or web pages
•Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
Notes
(1) Measuring conditions in acc. to EN 140401-802
(2) Rated voltage:
(3) The power dissipation on the resistors generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceed.
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
SIZE POWER RATING
P70 °C
W
LIMITING
ELEMENT
VOLTAGE
MAX.
V≅
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
RESISTANCE
RANGE
Ω
E-SERIES
INCH METRIC
D10 AP 0402 1005
0.063 50 ± 100
± 200
± 1
± 5
100R - 10M
10R - 10M
24 + 96
24
Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.5 A
D11 AP 0603 1608
0.1 75 ± 100
± 200
± 1
± 5
18R - 10M
3R6 - 10M
24 + 96
24
Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.7 A
D12 AP 0805 2012
0.125 150 ± 100
± 200
± 1
± 5
18R - 10M
3R6 - 10M
24 + 96
24
Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.8 A
D25 AP 1206 3216
0.25 200 ± 100
± 200
± 1
± 5
18R - 10M
3R6 - 10M
24 + 96
24
Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 1 A
TECHNICAL SPECIFICATIONS
PARAMETER UNIT D10 AP D11 AP D12 AP D25 AP
Rated Dissipation at 70
°
C (3) W 0.063 0.10 0.125 0.25
Limiting Element Voltage (2) V≅50 75 150 200
Insulation Voltage (1 min) Vpeak > 75 > 100 > 200 > 300
Thermal Resistance (1) K/W ≤ 870 ≤ 550 ≤ 440 ≤ 220
Insulation Resistance Ω> 109
Category Temperature Range
°
C - 55 to + 155
Failure Rate h-1 0.3 x 10- 9
Weight/1000 pieces g 0.65 2 5.5 10
PxR
Document Number: 20038 For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com
Revision: 02-Sep-08 2
D.. AP
Thick Film, Rectangular Chip Resistors
for Conductive Gluing Vishay
Notes
(1) Preferred way for ordering products is by use of the PART NUMBER
(2) Please refer to table PACKAGING, see below
(3) Detailed BV Number will appear on the Packaging Label
Note
(4) Flame treated paper for sizes D10 and D11. Regular paper for sizes D12 and D25.
PART NUMBER AND PRODUCT DESCRIPTION D.. AP - SERIES
Part Numbering: D1208058B5620FP5 (1)
MODEL/SIZE SPECIAL CHARACTER TCR VALUE TOLERANCE PA CK A GI N G (2) SPECIAL
D100402
D110603
D120805
D251206
8 = AgPd terminations
for conductive glueing
B = ± 100 ppm/K
A = ± 200 ppm/K
0 = Jumper
3 digit value
1 digit multiplier
MULTIPLIER
7 = *10-3
8 = *10-2
9 = *10-1
0 = *100
1 = *101
2 = *102
3 = *103
4 = *104
5 = *105
6 = *106
0000 = Jumper
F = ± 1 %
J = ± 5 %
0 = Jumper
P0
P5
PN
PZ
B5
BN
Up to 2 digits
Product Description: D12 AP 100 562R 1 % P5
D12 AP 100 562R 1 % P5 BVxxxx
MODEL TCR RESISTANCE VALUE TOLERANCE
PA C K AG I N G
(2)
SPECIAL (3)
D10 AP
D11 AP
D12 AP
D25 AP
± 100 ppm/K
± 200 ppm/K
49K9 = 49.9 kΩ
5R1 = 5.1 Ω
0R0 = Jumper
± 1 %
± 5 %
P0
P5
PN
PZ
B5
BN
Customized
part number is
available on
request
PACKAGING
MODEL
REEL
TAPE WIDTH DIAMETER PITCH PIECES/REEL PACKAGING CODE
PAPER (4) BLISTER
D10 AP 8 mm 180 mm/7" 2 mm 10 000 P0
PZ
330 mm/13" 2 mm 50 000
D11 AP 8 mm
180 mm/7" 4 mm 5000 P5 B5
255 mm/10" 4 mm 10 000 P0
330 mm/13" 4 mm 20 000 PN BN
D12 AP 8 mm
180 mm/7" 4 mm 5000 P5 B5
255 mm/10" 4 mm 10 000 P0
330 mm/13" 4 mm 20 000 PN BN
D25 AP 8 mm
180 mm/7" 4 mm 5000 P5 B5
255 mm/10" 4 mm 10 000 P0
330 mm/13" 4 mm 15 000 BN
330 mm/13" 4 mm 20 000 PN
5PF0265B8508021D
www.vishay.com For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 20038
3Revision: 02-Sep-08
D.. AP
Vishay Thick Film, Rectangular Chip Resistors
for Conductive Gluing
DIMENSIONS
FUNCTIONAL PERFORMANCE
SIZE DIMENSIONS [in millimeters]
INCH METRIC
LW H T1T2
0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2
+ 0.10
- 0.15
0603 1608 1.55
+ 0.10
- 0.05
0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2
0805 2012 2.0
+ 0.20
- 0.10
1.25 ± 0.15
0.45 ± 0.05 0.3
+ 0.20
- 0.10
0.3 ± 0.2
1206 3216 3.2
+ 0.10
- 0.20
1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2
SIZE GLUING PADS DIMENSIONS [in millimeters]
INCH METRIC a b l
0402 1005 0.4 0.6 0.5
0603 1608 0.9 0.9 1.0
0805 2012 0.9 1.3 1.3
1206 3216 1.1 1.7 2.3
0402 0603 0805 1206
90
80
70
60
50
40
30
20
10
0 0 0.1 0.2 0.3 0.4 0.5
Power in W
Temperature Rise in °C
Temperature Rise
- 55 - 25 0 25 50 75 100 125 155 175
120
100
80
60
40
20
0
70
DeratingAmbient Temperature in °C
Rated Power in %
100 1K 10K 100K 1M 10M
Non-Linearity
100
90
80
70
60
50
40
30
20
10
Resistance V alue in Ω
Non-Linearity A 3 in dB
1206
0805
0603
0402
120
110
100 1K 10K 100K 1M 10M
100
10
1
0.1
Current Noise Resistance V alue in Ω
Current Noise in µ V/ V
0402
0603
0805
1206
Document Number: 20038 For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com
Revision: 02-Sep-08 4
D.. AP
Thick Film, Rectangular Chip Resistors
for Conductive Gluing Vishay
1000
100
10
1
0.1
0.01
10-6 10-5 10-4 10-3 10-2 10-1 1 10
Single Pulse
Maximum pulse load, single pulse; applicable if P 0 and n ≤ 1000 and Û ≤ Û
max.
;
for permissible resistance change equivalent to 8000 h operation
Pulse Duration
i
(s)
Pulse Load max. (W)
1206
0805
0603
0402
P
t
Continuous Pulse
Continuous Pulse Load max. (W)
100
10
1
0.10
0.01
10
-6
10
-5
10
-4
10
-3
10
-2
10
-1
1 10
1206
0805
0603
0402
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑ
amb
) and Û ≤ Û
max.
;
for permissible resistance change equivalent to 8000 h operation
1206
0805
0603
0402
Pulse Duration
i
(s)
P
t
200
0
10-6 10-5 10-4 10-3 10-2 10-1 110
Pulse Voltage
Maximum pulse voltage, single and continuous pulses; applicable if
P ≤ P
max.
; for permissible resistance change equivalent to 8000 h operation
400
600
800
1000
1200
1400
Pulse Voltage
max.
(V)
1206
0805
0603
0402
100
300
500
700
900
1100
1300
Pulse Duration
i
(s)
U
t
www.vishay.com For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 20038
5Revision: 02-Sep-08
D.. AP
Vishay Thick Film, Rectangular Chip Resistors
for Conductive Gluing
D
25.. AP
D12.. AP
D 1 0.. AP
D1
1.. AP
≤ 10K
≤ 1
M
≤ 10
M
140
120
100
80
60
40
20
0
ϑs = f [ϑr]
Parameter:
ϑa
20 40 60 80 100 120 140 160 180
Load in W
0.01
0.1
1
20 40 60 80 100 120 140 160 180
Surface temperature ϑs in °C
0.01
0.1
1
10 1 0.1 0.01
Resistance change Δ / %
R
0.5 0.4 0.3 0.2 0.1 0
ϑr = f [P]
Parameter: Size
140
120
100
80
60
40
20
0
Stability nomogram typical values (for handling see general explanations)
Resistance change
[Δ / ] in % after 1000 h Temperature rise ϑr in °C
ϑ
a
= 20 °C
40 °C
60 °C
80 °C
100 °C
120 °C
140 °C
t
=
1
0 0
0
0
0 h
1 0
0 0 0
h
5 0
0
0
h
2
0 0
0 h
1
0 0
0 h
Surface temperature ϑs in °C
R
Δ / (t) = f [Δ / (t = 1000 h)]
Parameter: Time
R R
R R
Δ / [t = 1000 h] = f [ϑs]
Parameter:
Resistance value
R R
R R
0.25 W
0.125 W
0.0625 W
120
100
80
60
40
20
12 3 5 7 10 2 3 5 7 100 2 3 5 7 60 80 100 120 140
Surface temperature ϑ
s
[°C]
Number of mounted resistors [pieces]
Power rating as a function of packaging density (guideline)
ϑ
a
= 20 °C
ϑ
r
= [°C]
ϑ
a
= 40 °C
ϑ
a
= 60 °C
ϑ
a
= 80 °C
ϑ
a
= 100 °C
ϑ
a
= 120 °C
Document Number: 20038 For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com
Revision: 02-Sep-08 6
D.. AP
Thick Film, Rectangular Chip Resistors
for Conductive Gluing Vishay
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
TEST
(clause) CONDITIONS OF TEST
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR/R)
STABILITY CLASS 1 OR BETTER
D10 AP
D11 AP
D12 AP
D25 AP
Stability for product types: 100 Ω to 10 MΩ18 Ω to 10 MΩ
D..AP
Resistance (4.5) -± 1 %± 1 %
Endurance at 70 °C (4.25.1)
U = (P70 x R)1/2
U = Umax.; whichever is less severe
1.5 h ON; 0.5 h OFF; 70 °C; 1000 h
± 1.0 %
Endurance at upper category
temperature (4.25.3) UCT = 125 °C; 1000 h ± 1.0 %
Overload (4.13)
U = 2.5 x (P70 x R)1/2
≤ 2 x Umax.;
Duration: according the style
± 0.25 %
Rapid change of temperature (4.19) 30 min at LCT = - 55 °C
30 min at UCT = 125 °C; 5 cycles ± 0.25 %
Damp heat, steady state (4.24) (40 ± 2) °C; 56 days;
(93 ± 3) % RH ± 1.0 %
APPLICABLE SPECIFICATIONS
• EN 60115-1 Generic Specification
• EN 140400 Sectional Specification
• EN 140401-802 Detail Specification
• IEC 60068-2-X Variety of environmental test procedures
• IEC 60286-3 Packaging of SMD components
Document Number: 91000 www.vishay.com
Revision: 18-Jul-08 1
Disclaimer
Legal Disclaimer Notice
Vishay
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
