LMZ12001EXT LMZ12001EXT 1A SIMPLE SWITCHER(R) Power Module with 20V Maximum Input Voltage for Military and Rugged Applications Literature Number: SNVS661C LMZ12001EXT 1A SIMPLE SWITCHER(R) Power Module with 20V Maximum Input Voltage for Military and Rugged Applications Easy To Use 7 Pin Package Performance Benefits Low radiated emissions / High radiated immunity Passes vibration standard MIL-STD-883 Method 2007.2 Condition A JESD22-B103B Condition 1 Passes drop standard MIL-STD-883 Method 2002.3 Condition B JESD22-B110 Condition B 30117386 TO-PMOD 7 Pin Package 10.16 x 13.77 x 4.57 mm (0.4 x 0.542 x 0.18 in) JA = 20C/W, JC = 1.9C/W RoHS Compliant System Performance Efficiency VIN = 12V VOUT = 5.0V Electrical Specifications 6W maximum total power output Up to 1A output current Input voltage range 4.5V to 20V Output voltage range 0.8V to 6V Efficiency up to 92% Key Features -55C to 125C junction temperature range Integrated shielded inductor Simple PCB layout Flexible startup sequencing using external soft-start capacitor and precision enable Protection against inrush currents and faults such as input UVLO and output short circuit Single exposed pad and standard pinout for easy mounting and manufacturing Fast transient response for FPGAs and ASICs Low output voltage ripple Pin-to-pin compatible family: LMZ14203EXT/2EXT/1EXT (42V max 3A, 2A, 1A) LMZ14203/2/1 (42V max 3A, 2A, 1A) LMZ12003/2/1 (20V max 3A, 2A, 1A) Fully Webench(R) Power Designer enabled 30117318 Thermal Derating Curve VIN = 12V VOUT = 5.0V 30117319 Radiated Emissions (EN 55022 Class B) from Evaluation Board Applications Point of load conversions from 5V and 12V input rail Time critical projects Space constrained high thermal requirement applications Negative output voltage applications (See AN-2027) 30117350 (c) 2011 National Semiconductor Corporation 301173 www.national.com LMZ12001EXT 1A SIMPLE SWITCHER(R) Power Module with 20V Maximum Input Voltage for Military and Rugged Applications June 15, 2011 LMZ12001EXT Simplified Application Schematic 30117301 Connection Diagram 30117309 Top View 7-Lead TO-PMOD Ordering Information Order Number Package Type NSC Package Drawing Supplied As LMZ12001EXTTZ TO-PMOD-7 TZA07A 250 Units in Tape and Reel LMZ12001EXTTZX TO-PMOD-7 TZA07A 500 Units in Tape and Reel LMZ12001EXTTZE TO-PMOD-7 TZA07A 45 Units in a Rail Pin Descriptions Pin Name Description 1 VIN Supply input -- Nominal operating range is 4.5V to 20V . A small amount of internal capacitance is contained within the package assembly. Additional external input capacitance is required between this pin and exposed pad. 2 RON On Time Resistor -- An external resistor from VIN to this pin sets the on-time of the application. Typical values range from 25k to 124k ohms. 3 EN 4 GND 5 SS www.national.com Enable -- Input to the precision enable comparator. Rising threshold is 1.18V nominal; 90 mV hysteresis nominal. Maximum recommended input level is 6.5V. Ground -- Reference point for all stated voltages. Must be externally connected to EP. Soft-Start -- An internal 8 A current source charges an external capacitor to produce the soft-start function. This node is discharged at 200 A during disable, over-current, thermal shutdown and internal UVLO conditions. 2 6 7 EP Name Description FB Feedback -- Internally connected to the regulation, over-voltage, and short-circuit comparators. The regulation reference point is 0.8V at this input pin. Connected the feedback resistor divider between the output and ground to set the output voltage. VOUT Output Voltage -- Output from the internal inductor. Connect the output capacitor between this pin and exposed pad. EP Exposed Pad -- Internally connected to pin 4. Used to dissipate heat from the package during operation. Must be electrically connected to pin 4 external to the package. 3 www.national.com LMZ12001EXT Pin LMZ12001EXT ESD Susceptibility(Note 2) For soldering specifications: see product folder at www.national.com and www.national.com/ms/MS/MS-SOLDERING.pdf Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN, RON to GND EN, FB, SS to GND Junction Temperature Storage Temperature Range Operating Ratings -0.3V to 25V -0.3V to 7V 150C -65C to 150C 2 kV (Note 1) VIN EN Operation Junction Temperature 4.5V to 20V 0V to 6.5V -55C to 125C Electrical Characteristics Limits in standard type are for TJ = 25C only; limits in boldface type apply over the junction temperature (TJ) range of -55C to +125C. Minimum and Maximum limits are guaranteed through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 12V, Vout = 1.8V Symbol Parameter Conditions Min (Note 3) Typ (Note 4) Max (Note 3) Units 1.10 1.18 1.26 V SYSTEM PARAMETERS Enable Control VEN VEN-HYS EN threshold trip point VEN rising EN threshold hysteresis VEN falling SS source current VSS = 0V 90 mV Soft-Start ISS ISS-DIS 4.9 SS discharge current 8 11 -200 A A Current Limit ICL Current limit threshold d.c. average 1.4 2.0 3.0 A ON/OFF Timer tON-MIN tOFF ON timer minimum pulse width 150 ns OFF timer pulse width 260 ns Regulation and Over-Voltage Comparator VFB VFB-OV In-regulation feedback voltage VSS >+ 0.8V TJ = -55C to 125C IO = 1A 0.777 0.798 0.818 VSS >+ 0.8V TJ = 25C IO = 10 mA 0.786 0.802 0.818 Feedback over-voltage protection threshold V 0.92 V 5 nA IFB Feedback input bias current IQ Non Switching Input Current VFB= 0.86V 1 mA ISD Shut Down Quiescent Current VEN= 0V 25 A Thermal Shutdown Rising 165 C Thermal shutdown hysteresis Falling 15 C Junction to Ambient 4 layer JEDEC Printed Circuit Board, 100 vias, No air flow 19.3 C/W 2 layer JEDEC Printed Circuit Board, No air flow 21.5 C/W No air flow 1.9 C/W 8 mV PP .01 % Thermal Characteristics TSD TSD-HYST JA JC Junction to Case PERFORMANCE PARAMETERS VO VO/VIN www.national.com Output Voltage Ripple Line Regulation VIN = 8V to 20V, IO= 1A 4 VO/VIN Min (Note 3) Typ (Note 4) Max (Note 3) Parameter Conditions Units Load Regulation VIN = 12V 1.5 mV/A Efficiency VIN = 12V VO = 1.8V IO = 1A 85 % Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100pF capacitor discharged through a 1.5 k resistor into each pin. Test method is per JESD-22-114. Note 3: Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 4: Typical numbers are at 25C and represent the most likely parametric norm. Note 5: EN 55022:2006, +A1:2007, FCC Part 15 Subpart B: 2007. See AN-2024 and layout for information on device under test. Note 6: Theta JA measured on a 1.705" x 3.0" four layer board, with one ounce copper, thirty five 12 mil thermal vias, no air flow, and 1W power dissipation. Refer to PCB layout diagrams Typical Performance Characteristics Unless otherwise specified, the following conditions apply: VIN = 12V; Cin = 10uF X7R Ceramic; CO = 100uF X7R Ceramic; Tambient = 25 C for efficiency curves and waveforms. Efficiency 4.5V Input @ 25C Dissipation 4.5V Input @ 25C 30117351 30117352 Efficiency 5V Input @ 25C Dissipation 5V Input @ 25C 30117353 30117354 5 www.national.com LMZ12001EXT Symbol LMZ12001EXT Efficiency 6V Input @ 25C Dissipation 6V Input @ 25C 30117321 30117322 Efficiency 8V Input @ 25C Dissipation 8V Input @ 25C 30117355 30117356 Efficiency 12V Input @ 25C Dissipation 12V Input @ 25C 30117303 www.national.com 30117304 6 LMZ12001EXT Efficiency 20V Input @ 25C Dissipation 20V Input @ 25C 30117357 30117358 Efficiency 4.5V Input @ 85C Dissipation 4.5V Input @ 85C 30117359 30117360 Efficiency 5V Input @ 85C Dissipation 5V Input @ 85C 30117361 30117362 7 www.national.com LMZ12001EXT Efficiency 6V Input @ 85C Dissipation 6V Input @ 85C 30117333 30117334 Efficiency 8V Input @ 85C Dissipation 8V Input @ 85C 30117340 30117341 Efficiency 12V Input @ 85C Dissipation 12V Input @ 85C 30117342 www.national.com 30117343 8 LMZ12001EXT Efficiency 20V Input @ 85C Dissipation 20V Input @ 85C 30117363 30117364 Line and Load Regulation @ 25C Line and Load Regulation @ 85C 30117348 30117369 Line and Load Regulation @ -55C Output Ripple 12VIN 3.3VO 1A 30117305 30117370 9 www.national.com LMZ12001EXT Transient Response 12VIN 3.3VO 0.6A to 1A Step Current Limit 1.8VOUT @25C 30117306 30117365 Current Limit 3.3VOUT @25C Current Limit 1.8VOUT @85C 30117367 30117372 Current Limit 1.8VOUT @-55C Thermal Derating VOUT = 1.8V 30117371 www.national.com 30117366 10 LMZ12001EXT Application Block Diagram 30117308 *Program VO with divider resistor selection *Program turn-on time with soft-start capacitor selection *Select CO *Select CIN *Set operating frequency with RON *Determine module dissipation *Layout PCB for required thermal performance General Description The LMZ12001EXT SIMPLE SWITCHER(R) power module is an easy-to-use step-down DC-DC solution capable of driving up to 1A load with exceptional power conversion efficiency, line and load regulation, and output accuracy. The LMZ12001EXT is available in an innovative package that enhances thermal performance and allows for hand or machine soldering. The LMZ12001EXT can accept an input voltage rail between 4.5V and 20V and deliver an adjustable and highly accurate output voltage as low as 0.8V. The LMZ12001EXT only requires three external resistors and four external capacitors to complete the power solution. The LMZ12001EXT is a reliable and robust design with the following protection features: thermal shutdown, input under-voltage lockout, output over-voltage protection, short-circuit protection, output current limit, and allows startup into a pre-biased output. A single resistor adjusts the switching frequency up to 1 MHz. ENABLE DIVIDER, RENT AND RENB SELECTION The enable input provides a precise 1.18V band-gap rising threshold to allow direct logic drive or connection to a voltage divider from a higher enable voltage such as Vin. The enable input also incorporates 90 mV (typ) of hysteresis resulting in a falling threshold of 1.09V. The maximum recommended voltage into the EN pin is 6.5V. For applications where the midpoint of the enable divider exceeds 6.5V, a small zener can be added to limit this voltage. The function of this resistive divider is to allow the designer to choose an input voltage below which the circuit will be disabled. This implements the feature of programmable under voltage lockout. This is often used in battery powered systems to prevent deep discharge of the system battery. It is also useful in system designs for sequencing of output rails or to prevent early turn-on of the supply as the main input voltage rail rises at power-up. Applying the enable divider to the main input rail is often done in the case of higher input voltage systems where a lower boundary of operation should be established. In the case of sequencing supplies, the divider is connected to a rail that becomes active earlier in the powerup cycle than the LMZ12001EXT output rail. The two resistors should be chosen based on the following ratio: COT Control Circuit Overview Constant On Time control is based on a comparator and an on-time one shot, with the output voltage feedback compared with an internal 0.8V reference. If the feedback voltage is below the reference, the main MOSFET is turned on for a fixed on-time determined by a programming resistor RON. RON is connected to VIN such that on-time is reduced with increasing input supply voltage. Following this on-time, the main MOSFET remains off for a minimum of 260 ns. If the voltage on the feedback pin falls below the reference level again the on-time cycle is repeated. Regulation is achieved in this manner. Design Steps for the LMZ12001EXT Application RENT / RENB = (VIN UVLO / 1.18V) - 1 (1) The LMZ12001EXT demonstration and evaluation boards use 11.8k for RENB and 32.4k for RENT resulting in a rising UVLO of 4.5V. This divider presents 5.34V to the EN input when the divider input is raised to 20V. The LMZ12001EXT is fully supported by Webench(R) and offers the following: Component selection, electrical and thermal simulations as well as the build-it board for a reduction in design time. The following list of steps can be used to manually design the LMZ12001EXT application. *Select minimum operating VIN with enable divider resistors OUTPUT VOLTAGE SELECTION Output voltage is determined by a divider of two resistors connected between VO and ground. The midpoint of the di11 www.national.com LMZ12001EXT vider is connected to the FB input. The voltage at FB is compared to a 0.8V internal reference. In normal operation an on-time cycle is initiated when the voltage on the FB pin falls below 0.8V. The main MOSFET on-time cycle causes the output voltage to rise and the voltage at the FB to exceed 0.8V. As long as the voltage at FB is above 0.8V, on-time cycles will not occur. The regulated output voltage determined by the external divider resistors RFBT and RFBB is: erate with a minimum value. Ceramic capacitors or other low ESR types are recommended. See AN-2024 for more detail. The following equation provides a good first pass approximation of CO for load transient requirements: COISTEP*VFB*L*VIN/ (4*VO*(VIN--VO)*VOUT-TRAN)(6) Solving: CO 1A*0.8V*10H*12V / (4*3.3V*( 12V -- 3.3V)*33mV) 25F (7) VO = 0.8V * (1 + RFBT / RFBB) (2) The LMZ12001EXT demonstration and evaluation boards are populated with a 100 uF 6.3V X5R output capacitor. Locations for other output capacitors are provided. Rearranging terms; the ratio of the feedback resistors for a desired output voltage is: RFBT / RFBB = (VO / 0.8V) - 1 (3) CIN SELECTION The LMZ12001EXT module contains an internal 0.47 F input ceramic capacitor. Additional input capacitance is required external to the module to handle the input ripple current of the application. This input capacitance should be located in very close proximity to the module. Input capacitor selection is generally directed to satisfy the input ripple current requirements rather than by capacitance value. Worst case input ripple current rating is dictated by the equation: These resistors should be chosen from values in the range of 1.0 kohm to 10.0 kohm. For VO = 0.8V the FB pin can be connected to the output directly so long as an output preload resistor remains that draws more than 20uA. Converter operation requires this minimum load to create a small inductor ripple current and maintain proper regulation when no load is present. A feed-forward capacitor is placed in parallel with RFBT to improve load step transient response. Its value is usually determined experimentally by load stepping between DCM and CCM conduction modes and adjusting for best transient response and minimum output ripple. A table of values for RFBT , RFBB , CFF and RON is included in the applications schematic. I(CIN(RMS)) 1 /2 * IO * (D / 1-D) (8) where D VO / VIN (As a point of reference, the worst case ripple current will occur when the module is presented with full load current and when VIN = 2 * VO). Recommended minimum input capacitance is 10uF X7R ceramic with a voltage rating at least 25% higher than the maximum applied input voltage for the application. It is also recommended that attention be paid to the voltage and temperature deratings of the capacitor selected. It should be noted that ripple current rating of ceramic capacitors may be missing from the capacitor data sheet and you may have to contact the capacitor manufacturer for this rating. If the system design requires a certain minimum value of input ripple voltage VIN be maintained then the following equation may be used. SOFT-START CAPACITOR SELECTION Programmable soft-start permits the regulator to slowly ramp to its steady state operating point after being enabled, thereby reducing current inrush from the input supply and slowing the output voltage rise-time to prevent overshoot. Upon turn-on, after all UVLO conditions have been passed, an internal 8uA current source begins charging the external soft-start capacitor. The soft-start time duration to reach steady state operation is given by the formula: tSS = VREF * CSS / Iss = 0.8V * CSS / 8uA (4) CIN IO * D * (1-D) / fSW-CCM * VIN(9) This equation can be rearranged as follows: If VIN is 1% of VIN for a 20V input to 3.3V output application this equals 200 mV and fSW = 400 kHz. CSS = tSS * 8 A / 0.8V (5) CIN 1A * 3.3V/20V * (1- 3.3V/20V) / (400000 * 0.200 V) 1.7F Use of a 0.022F capacitor results in 2.2 msec soft-start interval which is recommended as a minimum value. As the soft-start input exceeds 0.8V the output of the power stage will be in regulation. The soft-start capacitor continues charging until it reaches approximately 3.8V on the SS pin. Voltage levels between 0.8V and 3.8V have no effect on other circuit operation. Note that the following conditions will reset the soft-start capacitor by discharging the SS input to ground with an internal 200 A current sink. * The enable input being "pulled low" * Thermal shutdown condition * Over-current fault * Internal Vcc UVLO (Approx 4V input to VIN) Additional bulk capacitance with higher ESR may be required to damp any resonant effects of the input capacitance and parasitic inductance of the incoming supply lines. RON RESISTOR SELECTION Many designs will begin with a desired switching frequency in mind. For that purpose the following equation can be used. fSW(CCM) VO / (1.3 * 10-10 * RON) (10) This can be rearranged as RON VO / (1.3 * 10 -10 * fSW(CCM) )(11) The selection of RON and fSW(CCM) must be confined by limitations in the on-time and off-time for the COT control section. The on-time of the LMZ12001EXT timer is determined by the resistor RON and the input voltage VIN. It is calculated as follows: CO SELECTION None of the required CO output capacitance is contained within the module. At a minimum, the output capacitor must meet the worst case minimum ripple current rating of 0.5 * ILR P-P, as calculated in equation (19) below. Beyond that, additional capacitance will reduce output ripple so long as the ESR is low enough to permit it. A minimum value of 10 F is generally required. Experimentation will be required if attempting to opwww.national.com tON = (1.3 * 10-10 * RON) / VIN (12) 12 Following is a typical waveform showing the boundary condition. Transition Mode Operation VIN = 12V, VO = 3.3V, IO = 0.29A fSW(MAX) = VO / (VIN(MAX) * 150 nsec) (13) This equation can be used to select RON if a certain operating frequency is desired so long as the minimum on-time of 150 ns is observed. The limit for RON can be calculated as follows: RON VIN(MAX) * 150 nsec / (1.3 * 10 -10) (14) If RON calculated in (11) is less than the minimum value determined in (14) a lower frequency should be selected. Alternatively, VIN(MAX) can also be limited in order to keep the frequency unchanged. Additionally note, the minimum off-time of 260 ns limits the maximum duty ratio. Larger RON (lower FSW) should be selected in any application requiring large duty ratio. Discontinuous Conduction and Continuous Conduction Modes At light load the regulator will operate in discontinuous conduction mode (DCM). With load currents above the critical conduction point, it will operate in continuous conduction mode (CCM). When operating in DCM the switching cycle begins at zero amps inductor current; increases up to a peak value, and then recedes back to zero before the end of the off-time. Note that during the period of time that inductor current is zero, all load current is supplied by the output capacitor. The next on-time period starts when the voltage on the at the FB pin falls below the internal reference. The switching frequency is lower in DCM and varies more with load current as compared to CCM. Conversion efficiency in DCM is maintained since conduction and switching losses are reduced with the smaller load and lower switching frequency. Operating frequency in DCM can be calculated as follows: 30117314 The inductor internal to the module is 10 H. This value was chosen as a good balance between low and high input voltage applications. The main parameter affected by the inductor is the amplitude of the inductor ripple current (ILR). ILR can be calculated with: ILR P-P=VO*(VIN- VO)/(10H*fSW*VIN) (17) Where VIN is the maximum input voltage and fSW is determined from equation 10. If the output current IO is determined by assuming that IO = IL, the higher and lower peak of ILR can be determined. Be aware that the lower peak of ILR must be positive if CCM operation is required. POWER DISSIPATION AND BOARD THERMAL REQUIREMENTS For the design case of VIN = 12V, VO = 1.8V, IO = 1A, TAMB (MAX) = 85C , and TJUNCTION = 125C, the device must see a thermal resistance from case to ambient of: fSW(DCM)VO*(VIN-1)*10H*1.18*1020*IO/(VIN-VO)*RON2 (15) In CCM, current flows through the inductor through the entire switching cycle and never falls to zero during the off-time. The switching frequency remains relatively constant with load current and line voltage variations. The CCM operating frequency can be calculated using equation 7 above. Following is a comparison pair of waveforms of the showing both CCM (upper) and DCM operating modes. CA< (TJ-MAX -- TAMB(MAX)) / PIC-LOSS - JC (18) Given the typical thermal resistance from junction to case to be 1.9 C/W .Use the 85C power dissipation curves in the Typical Performance Characteristics section to estimate the PIC-LOSS for the application being designed. In this application it is 0.4W CCM and DCM Operating Modes VIN = 12V, VO = 3.3V, IO = 1A/0.25A CA< (125 -- 85) / 0.4W --1.9 = 98.1 To reach CA = 98.1, the PCB is required to dissipate heat effectively. With no airflow and no external heat, a good estimate of the required board area covered by 1 oz. copper on both the top and bottom metal layers is: Board Area_cm2 = 500C x cm2/W / JC (19) As a result, approximately 5 square cm of 1 oz copper on top and bottom layers is required for the PCB design. The PCB copper heat sink must be connected to the exposed pad. Approximately thirty six, 10 mils (254 m) thermal vias spaced 59 mils (1.5 mm) apart must connect the top copper to the bottom copper. For an example of a high thermal performance PCB layout, refer to the Evaluation Board application note AN-2024. For more information on thermal design see AN- 2020 and AN-2026. 30117312 The approximate formula for determining the DCM/CCM boundary is as follows: 13 www.national.com LMZ12001EXT IDCBVO*(VIN-VO)/(2*10 H*fSW(CCM)*VIN) (16) The inverse relationship of tON and VIN gives a nearly constant switching frequency as VIN is varied. RON should be selected such that the on-time at maximum VIN is greater than 150 ns. The on-timer has a limiter to ensure a minimum of 150 ns for tON. This limits the maximum operating frequency, which is governed by the following equation: LMZ12001EXT PC BOARD LAYOUT GUIDELINES PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DCDC converter and surrounding circuitry by contributing to EMI, ground bounce and resistive voltage drop in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability. Good layout can be implemented by following a few simple design rules. Additional Features OUTPUT OVER-VOLTAGE COMPARATOR The voltage at FB is compared to a 0.92V internal reference. If FB rises above 0.92V the on-time is immediately terminated. This condition is known as over-voltage protection (OVP). It can occur if the input voltage is increased very suddenly or if the output load is decreased very suddenly. Once OVP is activated, the top MOSFET on-times will be inhibited until the condition clears. Additionally, the synchronous MOSFET will remain on until inductor current falls to zero. CURRENT LIMIT Current limit detection is carried out during the off-time by monitoring the current in the synchronous MOSFET. Referring to the Functional Block Diagram, when the top MOSFET is turned off, the inductor current flows through the load, the PGND pin and the internal synchronous MOSFET. If this current exceeds 1.5A (typical) the current limit comparator disables the start of the next on-time period. The next switching cycle will occur only if the FB input is less than 0.8V and the inductor current has decreased below 1.5A. Inductor current is monitored during the period of time the synchronous MOSFET is conducting. So long as inductor current exceeds 1.5A, further on-time intervals for the top MOSFET will not occur. Switching frequency is lower during current limit due to the longer off-time. It should also be noted that current limit is dependent on both duty cycle and temperature as illustrated in the graphs in the typical performance section. 30117311 1. Minimize area of switched current loops. From an EMI reduction standpoint, it is imperative to minimize the high di/dt current paths during PC board layout. The high current loops that do not overlap have high di/dt content that will cause observable high frequency noise on the output pin if the input capacitor CIN1 is placed a distance away for the LMZ12001. Therefore physically place CIN1 asa close as possible to the LMZ12001EXT VIN and GND exposed pad. This will minimize the high di/dt area and reduce radiated EMI. Additionally, grounding for both the input and output capacitor should consist of a localized top side plane that connects to the GND exposed pad (EP). 2. Have a single point ground. The ground connections for the feedback, soft-start, and enable components should be routed to the GND pin of the device. This prevents any switched or load currents from flowing in the analog ground traces. If not properly handled, poor grounding can result in degraded load regulation or erratic output voltage ripple behavior. Provide the single point ground connection from pin 4 to EP. 3. Minimize trace length to the FB pin. Both feedback resistors, RFBT and RFBB, and the feed forward capacitor CFF, should be located close to the FB pin. Since the FB node is high impedance, maintain the copper area as small as possible. The trace are from RFBT, RFBB, and CFF should be routed away from the body of the LMZ12001EXT to minimize noise. 4. Make input and output bus connections as wide as possible. This reduces any voltage drops on the input or output of the converter and maximizes efficiency. To optimize voltage accuracy at the load, ensure that a separate feedback voltage sense trace is made to the load. Doing so will correct for voltage drops and provide optimum output accuracy. 5. Provide adequate device heat-sinking. Use an array of heat-sinking vias to connect the exposed pad to the ground plane on the bottom PCB layer. If the PCB has a plurality of copper layers, these thermal vias can also be employed to make connection to inner layer heat-spreading ground planes. For best results use a 6 x 6 via array with minimum via diameter of 10mils (254 m) thermal vias spaced 59mils (1.5 mm). Ensure enough copper area is used for heatsinking to keep the junction temperature below 125C. www.national.com THERMAL PROTECTION The junction temperature of the LMZ12001EXT should not be allowed to exceed its maximum ratings. Thermal protection is implemented by an internal Thermal Shutdown circuit which activates at 165 C (typ) causing the device to enter a low power standby state. In this state the main MOSFET remains off causing VO to fall, and additionally the CSS capacitor is discharged to ground. Thermal protection helps prevent catastrophic failures for accidental device overheating. When the junction temperature falls back below 145 C (typ Hyst = 20 C) the SS pin is released, VO rises smoothly, and normal operation resumes. Applications requiring maximum output current especially those at high input voltage may require application derating at elevated temperatures. ZERO COIL CURRENT DETECTION The current of the lower (synchronous) MOSFET is monitored by a zero coil current detection circuit which inhibits the synchronous MOSFET when its current reaches zero until the next on-time. This circuit enables the DCM operating mode, which improves efficiency at light loads. 14 LMZ12001EXT Pre-Biased Startup PRE-BIASED STARTUP The LMZ12001EXT will properly start up into a pre-biased output. This startup situation is common in multiple rail logic applications where current paths may exist between different power rails during the startup sequence. The following scope capture shows proper behavior during this event. 30117325 15 www.national.com LMZ12001EXT Evaluation Board Schematic Diagram and BOM 30117307 Ref Des Description Case Size Case Size Manufacturer P/N LMZ12001EXTTZ-ADJ U1 SIMPLE SWITCHER (R) TO-PMOD-7 National Semiconductor Cin1 1 F, 50V, X7R 1206 Taiyo Yuden UMK316B7105KL-T Cin2 10 F, 50V, X7R 1210 Taiyo Yuden UMK325BJ106MM-T CO1 1 F, 50V, X7R 1206 Taiyo Yuden UMK316B7105KL-T CO2 100 F, 6.3V, X7R 1210 Taiyo Yuden JMK325BJ10CR7MM-T RFBT 1.37 k 0603 Vishay Dale CRCW06031K37FKEA RFBB 1.07 k 0603 Vishay Dale CRCW06031K07FKEA RON 32.4 k 0603 Vishay Dale CRCW060332K4FKEA RENT 32.4 k 0603 Vishay Dale CRCW060332K4FKEA RENB 11.8 k 0603 Vishay Dale CRCW060311k8FKEA CFF 22 nF, 10%, X7R, 16V 0603 TDK C1608X7R1H223K CSS 22 nF, 10%, X7R, 16V 0603 TDK C1608X7R1H223K D1 5.1V SOD-23 -- Optional www.national.com 16 LMZ12001EXT 30117316 30117317 FIGURE 1. Top And Bottom View Of Evaluation PCB 17 www.national.com LMZ12001EXT Physical Dimensions inches (millimeters) unless otherwise noted 7-Lead TZA Package NS Package Number TZA07A www.national.com 18 LMZ12001EXT Notes 19 www.national.com LMZ12001EXT 1A SIMPLE SWITCHER(R) Power Module with 20V Maximum Input Voltage for Military and Rugged Applications Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated