TC74HC4051,4052,4053AP/AF/AFT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74HC4051AP, TC74HC4051AF, TC74HC4051AFT TC74HC4052AP, TC74HC4052AF, TC74HC4052AFT TC74HC4053AP, TC74HC4053AF, TC74HC4053AFT TC74HC4051AP/AF/AFT 8-Channel Analog Multiplexer/Demultiplexer TC74HC4052AP/AF/AFT Dual 4-Channel Analog Multiplexer/Demultiplexer TC74HC4053AP/AF/AFT Triple 2-Channel Analog Multiplexer/Demultiplexer TC74HC4051AP, TC74HC4052AP, TC74HC4053AP TC74HC4051AF, TC74HC4052AF, TC74HC4053AF The TC74HC4051A/4052A/4053A are high speed CMOS ANALOG MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology. They achieve the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power dissipation. The TC74HC4051A has an 8 channel configuration, the TC74HC4052A has a 4 channel x 2 configuration and the TC74HC4053A has a 2 channel x 3 configuration. The digital signal to the control terminal turns "ON" the corresponding switch of each channel a large amplitude signal (VCC - VEE) can then be switched by the small logical amplitude (VCC - GND) control signal. For example, in the case of VCC = 5 V, GND = 0 V, VEE = -5 V, signals between -5 V and +5 V can be switched from the logical circuit with a single power supply of 5 V. As the ON-resistance of each switch is low, they can be connected to circuits with low input impedance. All inputs are equipped with protection circuits against static discharge or transient excess voltage. Features * * * * * * High speed: tpd = 15 ns (typ.) at VCC = 5 V, VEE = 0 V TC74HC4051AFT, TC74HC4052AFT, TC74HC4053AFT Weight DIP16-P-300-2.54A SOP16-P-300-1.27A TSSOP16-P-0044-0.65A : 1.00 g (typ.) : 0.18 g (typ.) : 0.06 g (typ.) Low power dissipation: ICC = 4 A (max) at Ta = 25C High noise immunity: VNIH = VNIL = 28% VCC (min) Low ON resistance: RON = 50 (typ.) at VCC - VEE = 9 V High noise immunity: THD = 0.02% (typ.) at VCC - VEE = 9 V Pin and function compatible with 4051/4052/4053B Start of commercial production 1986-05 1 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Pin Assignment TC74HC4051A TC74HC4052A 4 1 16 VCC 0Y 1 16 VCC 6 2 15 2 2Y 2 15 2X COM 3 14 1 Y-COM 3 14 1X 7 4 13 0 3Y 4 13 X-COM 5 5 12 3 1Y 5 12 0X INH 6 11 A INH 6 11 3X VEE 7 10 B VEE 7 10 A GND 8 9 C GND 8 9 B (top view) (top view) TC74HC4053A 1Y 1 16 VCC 0Y 2 15 Y-COM 1Z 3 14 X-COM Z-COM 4 13 1X 0Z 5 12 0X INH 6 11 A VEE 7 10 B GND 8 9 C (top view) 2 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT IEC Logic Symbol A B C INH COM INH A C (11) (10) (9) (6) (3) (6) (11) (9) X-COM B Y-COM C Z-COM (14) (10) TC74HC4051A MUXDMUX 0 0 8x 7 2 G8 A B INH 0 1 2 3 4 5 6 7 0 ... 7 (13) (14) (15) (12) (1) (5) (2) (4) 0 1 2 3 4 5 6 7 X-COM Y-COM (10) (9) (6) (13) (3) TC74HC4052A MUXDMUX 0 0 4x 1 3 G4 0 ... 3 0 1 2 3 (12) (14) (15) (11) (1) (5) (2) (4) 0X 1X 2X 3X 0Y 1Y 2Y 3Y TC74HC4053A MUXDMUX G2 2x0 2x1 0, 1 0 1 (12) (13) (2) (15) (9) (1) (5) (4) (3) 0X 1X 0Y 1Y 0Z 1Z Truth Table Control Inputs "ON" Channel Inhibit C* B A HC4051A HC4052A HC4053A L L L L 0 0X, 0Y 0X, 0Y, 0Z L L L H 1 1X, 1Y 1X, 0Y, 0Z L L H L 2 2X, 2Y 0X, 1Y, 0Z L L H H 3 3X, 3Y 1X, 1Y, 0Z L H L L 4 0X, 0Y, 1Z L H L H 5 1X, 0Y, 1Z L H H L 6 0X, 1Y, 1Z L H H H 7 1X, 1Y, 1Z H X X X None None None X: Don't care *: Except HC4052A 3 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT System Diagram TC74HC4051A COM Logic Level Converter I/O c O/I A B C 0 1 2 3 4 5 6 I/O c O/I INH 7 TC74HC4052A X-COM Logic Level Converter I/O c O/I A B 0X 1X 2X 3X 0Y 1Y 2Y I/O c O/I INH 3Y Y-COM TC74HC4053A Y-COM X-COM Logic Level Converter A B C I/O c O/I 1X 0Y 1Y 0Z I/O c O/I INH 0X 1Z Z-COM 4 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Supply voltage range VCC -0.5 to 7 V Supply voltage range VCC-VEE -0.5 to 13 V Control input voltage VIN -0.5 to VCC + 0.5 V Switch I/O voltage VI/O VEE - 0.5 to VCC + 0.5 V Control input diode current ICK 20 mA I/O diode current IIOK 20 mA IT 25 mA DC VCC or ground current ICC 50 mA Power dissipation PD 500 (DIP) (Note 2)/180 (SOP/TSSOP) mW Storage temperature Tstg -65 to 150 C Switch through current Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: 500 mW in the range of Ta = -40 to 65C. From Ta = 65 to 85C a derating factor of -10 mW/C should be applied up to 300 mW. Operating Ranges (Note) Characteristics Symbol Rating Unit Supply voltage range VCC 2 to 6 V Supply voltage range VEE -6 to 0 V Supply voltage range VCC-VEE 2 to 12 V Control input voltage VIN 0 to VCC V Switch I/O voltage VI/O VEE to VCC V Operating temperature Topr -40 to 85 C 0 to 1000 (VCC = 2.0 V) Control input rise and fall time tr, tf 0 to 500 (VCC = 4.5 V) ns 0 to 400 (VCC = 6.0 V) Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused control inputs must be tied to either VCC or GND. 5 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Electrical Characteristics DC Characteristics Test Condition Characteristics VEE (V) VCC (V) High-level control input voltage Low-level control input voltage ON resistance VIHC VILC RON Input/output leakage current (switch off) Switch input leakage current Max Min Max 2.0 1.50 1.50 4.5 3.15 3.15 6.0 4.20 4.20 2.0 0.50 0.50 4.5 1.35 1.35 6.0 1.80 1.80 4.5 85 180 225 VI/O = VCC to VEE -4.5 4.5 55 120 150 II/O 2 mA -6.0 6.0 50 100 125 GND 2.0 150 GND 4.5 70 150 190 -4.5 4.5 50 100 125 -6.0 6.0 45 80 100 VIN = VILC or VIHC GND 4.5 10 30 35 VI/O = VCC to VEE -4.5 4.5 5 12 15 II/O 2 mA -6.0 6.0 5 10 12 GND 6.0 60 600 -6.0 6.0 100 1000 VOS = VCC or GND GND 6.0 60 600 VIN = VILC or VIHC -6.0 6.0 100 1000 GND 6.0 0.1 1.0 GND 6.0 4.0 40.0 -6.0 6.0 8.0 80.0 VIN = VILC or VIHC VOS = VCC or GND IOFF Typ. GND II/O 2 mA RON Min VIN = VILC or VIHC VI/O = VCC or VEE Difference of ON resistance between switches Ta = -40 to 85C Ta = 25C Symbol VIS = GND or VCC VIN = VILC or VIHC IIZ (switch on, output open) Control input current IIN VIN = VCC or GND Quiescent supply current ICC VIN = VCC or GND 6 Unit V V nA nA A A 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT AC Characteristics (CL = 50 pF, input: tr = tf = 6 ns, GND = 0 V) Test Condition Characteristics VEE (V) VCC (V) Phase difference between input and output I/O All types 4051A Output enable time tpZL tpZH 4052A 4053A 4051A Output disable time tpLZ tpHZ 4052A 4053A Control input capacitance CIN (Note 1) (Note 1) (Note 1) (Note 1) (Note 1) (Note 1) All types SWITCH terminal capacitance CIS COS CPD Min Max 25 60 75 GND 4.5 6 12 15 GND 6.0 5 10 13 -4.5 4.5 4 GND 2.0 64 225 280 GND 4.5 18 45 56 GND 6.0 15 38 48 -4.5 4.5 18 280 GND 2.0 64 225 GND 4.5 18 45 56 GND 6.0 15 38 48 -4.5 4.5 18 GND 2.0 50 225 280 GND 4.5 14 45 56 GND 6.0 12 38 48 -4.5 4.5 14 GND 2.0 100 250 315 GND 4.5 33 50 63 GND 6.0 28 43 54 -4.5 4.5 29 GND 2.0 100 250 315 GND 4.5 33 50 63 GND 6.0 28 43 54 -4.5 4.5 29 GND 2.0 95 225 280 GND 4.5 30 45 56 GND 6.0 26 38 48 -4.5 4.5 26 5 10 10 36 70 70 19 40 40 4053A 11 20 20 4051A 7 15 15 7 15 15 7 15 15 0.95 2 2 0.85 2 2 0.75 2 2 70 71 67 4052A -5.0 4052A -5.0 5.0 5.0 4052A -5.0 5.0 4053A Power dissipation capacitance Max 4051A CIOS Typ. 2.0 4053A Feedthrough capacitance Min GND 4051A COMMON terminal capacitance Ta = -40 to 85C Ta = 25C Symbol 4051A (Note 2) 4052A (Note 2) 4053A (Note 2) GND 5.0 Unit ns ns ns pF pF pF pF pF Note 1: RL = 1 k Note 2: CPD is defined as the value of the internal equivalent capacitance of IC which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD*VCC*fIN + ICC 7 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Analog Switch Characteristics (GND = 0 V, Ta = 25C) (Note 1) Test Condition Characteristics Symbol Sine wave distortion (T.H.D) VEE (V) VCC (V) Typ. RL = 10 k, VIN = 4.0 Vp-p -2.25 2.25 0.025 CL = 50 pF VIN = 8.0 Vp-p -4.5 4.5 0.020 fIN = 1 kHz VIN = 11.0 Vp-p -6.0 6.0 0.018 All (Note 2) 45 -2.25 Frequency response (switch on) fmax Increase fIN frequency until dB meter reads -3dB RL = 50 , CL = 10 pF fIN = 1 MHz, sine wave 2.25 4052A (Note 3) 70 4053A (Note 3) 95 All 190 (Note 2) 4051A (Note 3) 70 -4.5 4.5 110 4053A (Note 3) 150 All 200 (Note 2) 4051A (Note 3) 85 -6.0 Feed through attenuation (switch off) MHz 4052A (Note 3) 6.0 4052A (Note 3) 140 4053A (Note 3) 190 VIN is centered at (VCC - VEE)/2 % 120 4051A (Note 3) Adjust fIN voltage to obtain 0dBm at VOS Unit -2.25 2.25 -50 -4.5 4.5 -50 -6.0 6.0 -50 -2.25 2.25 60 -4.5 4.5 140 -6.0 6.0 200 Adjust input for 0dBm RL = 600 , CL = 50 pF dB fIN = 1 MHz, sine wave Crosstalk (control input to signal output) RL = 600 , CL = 50 pF fIN = 1 MHz, square wave (tr = tf = 6 ns) Adjust VIN to obtain 0dBm at input Crosstalk (between any switches) -2.25 2.25 -50 RL = 600 , CL = 50 pF -4.5 4.5 -50 fIN = 1 MHz, sine wave -6.0 6.0 -50 mV dB Note 1: These characteristics are determined by design of devices. Note 2: Input COMMON terminal, and measured at SWITCH terminal. Note 3: Input SWITCH terminal, and measured at COMMON terminal. SWITCH terminal COMMON terminal 8 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Switching Characteristics Test Circuits 1. tpLZ, tpHZ, tpZL, tpZH 6 ns VCC VC C I/O S1 VCC 50% GND VCC O/I VEE 1 k GND 90% VO/I (S1 = VCC, S2 = GND) S2 VOH 50% tpZH 50 pF from P.G 90% 10% 6 ns VO/I (S1 = GND, S2 = VCC) tpHZ 50% tpZL VOL VOH 10% tpLZ VOL 2. Cross Talk (control input-switch output) fIN = 1 MHz duty = 50% tr = tf = 6 ns VCC C VCC 600 I/O VEE O/I GND 50 pF from P.G 600 -VCC GND 3. Feedthrough Attenuation VCC I/O VEE O/I GND 50 pF VIN 600 0.1 F VCC 600 C 9 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT 4. CIOS, CIS, COS CIOS VCC C I/O VEE COS COMMON O/I GND CIS SWITCH VCC 5. Cross Talk (between any two switches) VCC I/O O/I 600 0.1 F 600 C O/I 600 600 I/O 50 pF VIN VCC VEE GND 50 pF C 6. Frequency Response (switch on) VCC I/O O/I 0.1 F VEE GND 10 pF VIN VCC 50 C 10 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Package Dimensions Weight: 1.00 g (typ.) 11 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Package Dimensions Weight: 0.18 g (typ.) 12 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT Package Dimensions Weight: 0.06 g (typ.) 13 2016-10-18 TC74HC4051,4052,4053AP/AF/AFT RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 14 2016-10-18