ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Description Features The ICS601-01 is a low-cost, low phase noise, high-performance clock synthesizer for applications which require low phase noise and low jitter. It is ICS' lowest phase noise multiplier, and also the lowest CMOS part in the industry. Using ICS' patented analong and digital Phase-Locked Loop (PLL) techniques, the chip accepts a 10 - 27 MHz crystal or clock input, and produces output clocks up to 156 MHz at 3.3 V. * * * * * * * * This product is intended for clock generation. It has low output jitter (variation in the output period), but input and output skew and jitter are not defined nor guaranteed. For applications which require definted input to output timing, use the ICS670-01. Packaged in 16-pin SOIC or TSSOP Available in Pb (lead) free package Uses fundamental 10 - 27 MHz crystal or clock Patented PLL with the lowest phase noise Output clocks up to 156 MHz at 3.3 V Low phase noise: -132 dBc/Hz at 10 kHz Low jitter - 18 ps one sigma typ. Full swing CMOS outputs with 25 mA drive capability at TTL levels * Advanced, low power, sub-micron CMOS process * Industrial temperature range available * Operating voltage of 3.3V or 5V Block Diagram VDD 3 Reference Divider Phase Comparator Charge Pump Loop Filter CLK VCO X1/ICLK Crystal or clock input VCO Divide Crystal Oscillator X2 REFOUT ROM Based Multipliers 3 4 REFEN 1 MDS 601-01 L I n t e gra te d C i r c u i t S y s t e m s OE GND S3:0 525 Race Stre et, San Jo se, CA 9 5126 Revision 111204 te l (40 8) 2 97-12 01 w w w. i c st . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Pin Assignment Multiplier Select Table CLK 1 16 GND REFEN 2 15 GND VDD 3 14 GND S3 S2 S1 S0 CLK (see note 2 on following page) 0 0 0 0 TEST 0 0 0 1 TEST VDD 4 13 REFOUT 0 0 1 0 Input x1 VDD 5 12 OE 0 0 1 1 Input x3 X2 6 11 S0 0 1 0 0 Input x4 S1 7 10 S3 0 1 0 1 Input x5 X1/ICLK 8 9 S2 0 1 1 0 Input x6 16 Pin (150 mil) TSSOP or SOIC 0 1 1 1 Input x8 1 0 0 0 TEST 1 0 0 1 Crystal osc. pass through (no PLL) 1 0 1 0 Input x2 1 0 1 1 TEST 1 1 0 0 Input x8 1 1 0 1 Input x10 1 1 1 0 Input x12 1 1 1 1 Input x16 0 = connect directly to ground 1 = connect directly to VDD Pin Descriptions Pin Number Pin Name Pin Type 1 CLK Output 2 REFEN Input Reference clock enable. Turns off the buffered crystal oscillator clock (stops low) when low. 3 VDD Power Connect to +3.3V or +5V. Must match other VDDs. 4 VDD Power Connect to +3.3V or +5V. Must match other VDDs. 5 VDD Power Connect to +3.3V or +5V. Must match other VDDs. 6 X2 XO 7 S1 Input 8 X1/ICLK XI 9 S2 Input Multiplier select pin 2. Determines CLK output per table above. Internal pull-up. 10 S3 Input Multiplier select pin 3. Determines CLK output per table above. Internal pull-up. 11 S0 Input Multiplier select pin 0. Determines CLK output per table above. Internal pull-up. 12 OE Input Output Enable. Tri-states both output clocks when low. Internal pull-up. 13 REFOUT Output Buffered crystal oscillator clock output. Controlled by REFIN. 14 - 16 GND Power Connect to ground. Clock output from VCO. Output frequency equals the input frequency times multiplier. Crystal connection. Connect to a 10 - 27 MHz fundamental parallel mode crystal. Leave disconnected for an external clock input. Multiplier select pin 1. Determines CLK output per table above. Internal pull-up. Crystal connection. Connect to a 10 - 27 MHz fundamental parallel mode crystal or clock. 2 MDS 601-01 L In te grated Circuit Systems Pin Description 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Achieving Low Phase Noise Figure 1 shows a typical phase noise measurement in a 125 MHz system. Therea are a few simple steps that can be taken to achieve these levels of phase noise from the ICS601-01. Variations in VDD will increase the hase noise, so it is important to have a stable, low noise supply voltage at the device. Use decoupling capacitors of 0.1F in parallel with 0.01F. It is important to have these capacitors as close as possible to the ICS601-01 supply pins. Disabling the REFOUT clock is also important for achieving low phase noise; lab tests have shown that this can reduce the phase noise by as much as 10 dBc/Hz. 0 Phase Noise (dBc/Hz) -20 -40 -60 -80 -100 -120 -140 1.00E+01 1.00E+02 1.00E+03 1.00E+04 1.00E+05 1.00E+06 1.00E+07 Offset fromCarrier (Hz) Figure 1. Phase Noise of ICS601-01 for 125 MHz output, 25 MHz crystal input. VDD=3.3 V, REFOUTdisabled. External Component/Crystal Selection The ICS601-01 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.01F and 0.1F should be connected between VDD and GND, as close to the part as possible. A series termination resistor of 33 may be used for each clock output. The crystal must be connected as close to the chip as possible. The crystal should be fundamental mode, parallel resonant. Do not use third overtone. For exact tuning when using a crystal, capacitors should beconnected from pins X1 to ground and X2 to ground. In general, the value of these capacitors is given by the following equation, where CL is the crystal load capacitance: Crystal caps (pF) = (CL - 5) x 2. So for a crystal with 16 pF load capacitance, two 22 pF caps can be used. For any given board layout, ICS can measure the board capacitance and recommend the exact capacitance value to use. 3 MDS 601-01 L In te grated Circuit Systems 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS601-01. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature, Commercial version 0 to +70 C Ambient Operating Temperature, Industrial version -40 to +85 C Storage Temperature -65 to +150 C Junction Temperature 125 C Soldering Temperature 260 C Recommended Operation Conditions Parameter Min. Typ. Max. Units Ambient Operating Temperature -40 +85 C Power Supply Voltage (measured in respect to GND) +3.0 +5.5 V DC Electrical Characteristics VDD=3.3 V 10%, Ambient temperature -40 to +85C Parameter Symbol Conditions Operating Voltage VDD Input High Voltage VIH X1/ICLK pin only Note 1 Input Low Voltage VIL X1/ICLK pin only Note 1 Input High Voltage VIH Input Low Voltage VIL Output High Voltage VOH Output Low Voltage VOL MDS 601-01 L In te grated Circuit Systems Min. Typ. 3.0 Max. Units 5.5 V VDD/2+1 V VDD/2-1 2 V 0.8 CMOS level IOH = -4mA VDD-0.4 IOH = -12mA 2.4 V V V IOL = 12mA 0.4 4 Revision 111204 525 Ra ce Street, San Jose, CA 9512 6 tel (4 08) 297-1 201 V w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Parameter Symbol Conditions IDD No load, 125 MHz Operating Supply Current Short Circuit Current Min. Each output Input Capacitance CIN 40 OE, select pins Typ. Max. Units 22 30 mA 60 mA 5 pF Note 1: Switching occurs nominally at VDD/2 AC Electrical Characteristics VDD = 3.3V 10%, Ambient Temperature -40 to +85 C Parameter Symbol Input Frequency Conditions Min. Max. Units 27 MHz at 3.3V or 5V 156 MHz Fin Typ. 10 Output Frequency Output Rise Time tOR 0.8 to 2.0V no load 1.5 ns Output Fall Time tOF 0.8 to 2.0V, no load 1.5 ns 50 55 % Output Clock Duty Cycle at VDD/2 45 Maximum Absolute jitter, short term, 125 MHz No load 50 75 ps Maximum jitter, one sigma, 125 MHz (x5) No load 12 20 ps Phase Noise, relative to carrier, 125 MHz (x5) 100 Hz offset -90 -94 dBc/Hz Phase Noise, relative to carrier, 125 MHz (x5) 1 kHz -116 -120 dBc/Hz Phase Noise, relative to carrier, 125 MHz (x5) 10 kHz offset -118 -122 dBc/Hz Phase Noise, relative to carrier, 125 MHz (x5) 100 kHz offset -115 -119 dBc/Hz Note 2: Input frequency limited by maximum output frequency and multiplication factor (I.e. For 16x, maximum input frequency is 13.75 MHz). 5 MDS 601-01 L In te grated Circuit Systems 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Package Outline and Package Dimensions (16 pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 16 SOIC Symbol E H I N D E X A R E A 1 Min A A1 B C D E e H L 2 D Max 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 9.80 10.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.40 1.27 0 8 A A1 C -C e S E A TIN G P LA N E B L .1 0 (.0 0 4 ) 6 MDS 601-01 L In te grated Circuit Systems C 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Package Outline and Package Dimensions (16-pin TSSOP, 4.40 mm Body, 0.65 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 16 Symbol E1 A A1 A2 b C D E E1 e L E INDEX AREA 1 2 D A 2 Min Inches Max -1.20 0.05 0.15 0.80 1.05 0.19 0.30 0.09 0.20 4.90 5.1 6.40 BASIC 4.30 4.50 0.65 Basic 0.45 0.75 0 8 Min Max -0.047 0.002 0.006 0.032 0.041 0.007 0.012 0.0035 0.008 0.193 0.201 0.252 BASIC 0.169 0.177 0.0256 Basic 0.018 0.030 0 8 A A 1 c -Ce SEATING PLANE b L .10 (.004) 7 MDS 601-01 L In te grated Circuit Systems C 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m ICS601-01 LOW PHASE NOISE CLOCK MULTIPLIER Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature ICS601M-01 ICS601M-01 Tubes 16-pin narrow SOIC 0 to 70 C ICS601M-01T ICS601M-01 Tape and Reel 16-pin narrow SOIC 0 to 70 C ICS601M-01I ICS601M-01I Tubes 16-pin narrow SOIC -40 to 85 C ICS601M-01IT ICS601M-01I Tape and Reel 16-pin narrow SOIC -40 to 85 C ICS601M-01LF ICS601M-01LF Tubes 16-pin narrow SOIC 0 to 70 C ICS601M-01LFT ICS601M-01LF Tape and Reel 16-pin narrow SOIC 0 to 70 C ICS601M-01ILF ICS601M01ILF Tubes 16-pin narrow SOIC -40 to 85 C ICS601M-01ILFT ICS601M01ILF Tape and Reel 16-pin narrow SOIC -40 to 85 C ICS601G-01 601G-01 Tubes 16-pin TSSOP 0 to 70 C ICS601G-01T 601G-01 Tape and Reel 16-pin TSSOP 0 to 70 C ICS601G-01I 601G-01I Tubes 16-pin TSSOP -40 to 85 C ICS601G-01IT 601G-01I Tape and Reel 16-pin TSSOP -40 to 85 C ICS601G-01LF 601G01LF Tubes 16-pin TSSOP 0 to 70 C ICS601G-01LFT 601G01LF Tape and Reel 16-pin TSSOP 0 to 70 C ICS601G-01ILF 601G01IL Tubes 16-pin TSSOP -40 to 85 C ICS601G-01ILFT 601G01IL Tape and Reel 16-pin TSSOP -40 to 85 C "L" designates Pb (lead) free package; "I" designates industrial grade. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 8 MDS 601-01 L In te grated Circuit Systems 525 Ra ce Street, San Jose, CA 9512 6 Revision 111204 tel (4 08) 297-1 201 w w w. i c s t . c o m