SDX005IND4 - Honeywell - Datasheet.Live

Microstructure Pressure Sensors

Compensated 0 in H2O to 5 H2O in H2O

and 0 in H2O to 10 in H2O SDX IND Serie

Sensing and Control

FEATURES

• Low Cost Dual Inline

Package

• Temperature Compensated

• Calibrated Zero and Span

• Small Size

• Low Noise

• High Impendance for Low

Power Applications

TYPICAL APPLICAT IONS

• Medical Equipment

• Computer Peripherals

• Pneumatic Controls

• HVAC

The SDX series sensors provide a very cost effective solution for pressure

applications that require small size plus performance. These calibrated and

temperature compensated sensors give an accurate and stable output over

a 0

C to 50

C [32

F to 122

F] range. This series is intended for use with

non-corrosive, non-ionic working fluids, such as, air and other dry gases.

The SDX series devices are specifically designed to measure low

pressures with a 0 in H2O to 10.0 in H2O full scale range. The output of the

bridge is ratiometric to the supply voltage up to 20.0 Vdc is acceptable.

The SDX series devices feature an integrated circuit sensor element and

laser trimmed thick film ceramic housed in a compact solvent resistant case.

The package is a double wide (i.e. 15,24 mm [0.600 in] lead spacing) dual

inline package. This is the same familiar package used by IC manufactures

except it has integral pressure port(s). The PC board area used by each DIP

is approximately 6,60 mm² [0.26 in²]. This extremely small size enables the

use of multiple sensors in limited available space. The DIP provides

excellent isolation to external package stress.

The DIP mounts on a PC board like a standard IC with through-hole pins.

The pins anchor the pressure sensor to the PC board which provides a more

secure and stable unit than other types of packages.

WARNING

MISUSE OF DOCUMENTATION

• The information presented in this product sheet is for reference

only. Do not use this document as a product installation guide.

• Complete installation, operation, and maintenance information is

provided in the instructions supplied with each product.

Failure to comply with these instructions could result in death or

serious injury.

WARNING

PERSONAL INJURY

DO NOT USE these

products as safety or

emergency stop devices or

in any other application

where failure of the product

could result in personal

injury.

Failure to comply with

these instructions could

result in death or serious

injury.

Microstructure Pressure Sensors

Compensated 0 in H2O to 5 in H2O

and 0 in H2O to 10 in H2O SDX IND Series

Honeywell • Sensing and Control 2

PRESSURE RANGE SPECIFICATIONS

Full-Scale Span (1)

Listing Operating Pressure Proof Pressure Min. Typ. Max.

SDX005IND4 0 in H2O to 5 in H2O 193 in H2O 19.5 mV 20.0 mV 20.5 mV

SDX010IND4 0 in H2O to 10 in H2O 193 in H2O 24.5 mV 25.0 mV 25.5 mV

GENERAL SPECIFICATIONS (all devices)

Characteristic Description (Maximum Ratings)

Supply Voltage (VS) 20.0 Vdc

Maximum Pressure on any Port 50 psig

Lead Temperature (Soldering 10 Sec.) 250 °C [482 °F]

Burst Pressure 193 H2O [7 psi]

ENVIRONMENTAL SPECIFICATIONS (all devices)

Compensated Operating Temperature 0 °C to 50 °C [32 °F to 122 °F]

Operating Temperature -40 °C to 85 °C [-40 °F to 185 °F]

Storage Temperature -55 °C to 125 °C [-67°F to 257 °F]

Humidity Limits 0 % RH to 100 % RH

PERFORMANCE SPECIFICATIONS (all devices) (2)

Characteristic Min. Typ. Max. Unit

Zero Pressure Offset -1.0 0 + 1.0 mV

Combined Linearity and Hysteresis (3) – ± 0.2 ± 1.0 % FSS

Temperature Effect on Span 0

C to 50

C [32

F to 122

F] (4) – ± 0.4 ± 2.0 % FSS

Temperature Effect on Offset 0

C to 50

C [32

F to 122

F] (4) – ± 0.2 ± 0.6 mV

Repeatability (5) – ± 0.5 – % FSS

Input Resistance (6) – 4.0 – KΩ

Output Resistance (7) – 4.0 – KΩ

Common-Mode Voltage(8) 1.5 3.0 5.0 Vdc

Response Time(9) – 100 – µsec

Long Term Stability of Offset and Span (10) – ± 0.1 – % FSS

SPECIFICATION NOTES

Note 1: Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Span is

ratiometric to the supply voltage.

Note 2: Reference conditions (unless otherwise noted): Supply voltage, VS = 12 Vdc, TA = 25

C [77

F], Common Mode Line Pressure =

0 psig, pressure applied to port 2

Note 3: Hysteresis is the maximum output difference at any point within the operating pressure range fro increasing and decreasing

pressure.

Note 4: Maximum error band of the offset voltage and the error band of the span, relative to the 25

C [77

F] reading.

Note 5: Maximum difference in output at any pressure with the operating pressure range and temperature within 0

C to 50

C [32

F to

122

F] after:

a) 100 temperature cycles, °C to 50 °C [32 °F to 122 °F]

b) 1.0 million pressure cycles, 0 in H2O to full-scale span

Note 6: Input impedance is the impedance between VS and ground

Note 7: Output impedance is the impedance between the + and – outputs.

Note 8: This is the common-mode voltage of the output arms for VS = 12 Vdc

Note 9: Response time for a 0 psi to full-scale span pressure step change, 10 % to 90 % rise time.

Note 10: Long term stability over a one year period.

Microstructure Pressure Sensors

Compensated 0 in H2O to 5 in H2O

and 0 in H2O to 10 inH2O SDX IND Series

Honeywell • Sensing and Control 3

PHYSICA L DIMENSIONS for reference only mm [in]

10,9

[.43] TYP.

14,0

[.55]

11,9

[.47]

3,4

[.135]

COMPENSATION

CERAMIC

6,4

[.250]

0,3

[.01] TYP.

15,2

[.60] TYP. 2,5

[.10] TYP.

0,5

[.02] TYP.

3,2

[.12] TYP.

6,6

[.30] TYP.

2,3 [.09] TYP.

2O DRAFT

2,8

[.11] TYP.

8,6

[.34] TYP.

PORT CONFIGURATION

Microstructure Pressure Sensors

Compensated 0 in H2O to 5 in H2O

and 0 in H2O to 10 in H2O SDX IND Series

Sensing and Contr ol

www.honeywell.com/sensing

Honeywell

11 West Spring Street

Freeport, Illinois 61032

008093-2-EN IL50 GLO 504 Printed in USA

EQUIVALENT CIRCUIT

- OUT

+ OUT

ELECTRICAL CONNECTIONS

OUTPUT +

OUTPUT -

GROUND V

ORDER INFORMATION

Listings Operating Pressure Range

SDX005IND4 0 in H2O to 5 in H2O

SDX010IND4 0 in H2O to 10 in H2O

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as

being free of defective materials and faulty

workmanship. Contact your local sales office for

warranty information. If warranted goods are

returned to Honeywell during the period of coverage,

Honeywell will repair or replace without charge those

items it finds defective. The foregoing is Buyer’s

sole remedy and is in lieu of all other warranties,

expressed or implied, including those of

merchantability and fitness for a particular

purpose.

Specifications may change without notice. The

information we supply is believed to be accurate and

reliable as of this printing. However, we assume no

responsibility for its use.

While we provide application assistance personally,

through our literature and the Honeywell web site, it

is up to the customer to determine the suitability of

the product in the application.

For application assistance, current specifications, or

name of the nearest Authorized Distributor, contact a

nearby sales office. Or call:

1-800-537-6945 USA/Canada

1-815-235-6847 International

FAX

1-815-235-6545 USA

INTERNET

www.honeywell.com/sensing

info.sc@honeywell.com