HRF-SW1001 SPDT Absorptive RF Switch Features x x x x x x x x High Isolation Of > 40 dB @ 2 GHz Low Insertion Loss Of 1.1dB @ 2 GHz DC To 2.5 GHz Operating Frequency Integrated CMOS Control Logic Integrated ESD Protection on Digital I/O Single Positive Supply Voltage Ultra Small LPCCTM Packaging Impedance matched for 75 Ohm systems Product Description HRF-SW1001 in LPCCTM Package The Honeywell HRF-SW1001 is a high performance single pole double throw (SPDT) absorptive RF switch that is ideal for use in wireless basestation and handset applications that require minimum power and minimum insertion loss. The HRF-SW1001 is manufactured with Honeywell's patented Silicon On Insulator (SOI) CMOS technology, which provides the performance of GaAs with the economy and integration capabilities of conventional CMOS technology. RF Electrical Specifications @ + 25oC Results @ Vdd=5.0 =/- 10%, Vss = 0 unless otherwise stated, Z0=75 ohms Parameter Test Condition Frequency Minimum Insertion Loss* DC - 0.5 GHz 2.0 GHz 2.5 GHz DC - 0.5 GHz 2.0 GHz 2.5 GHz DC - 0.5 GHz 2.0 GHz 2.5 GHz Isolation* VSWR* 1dB Compression* Input IP3* Trise, Tfall* Ton, Toff Transients *Guaranteed by design 52 45 41 Typical Maximum Units 0.8 0.9 1.1 55 49 44 1.1:1 1.2:1 1.3:1 1.1 1.4 1.5 dB dB dB dB dB dB Ratio Ratio Ratio 1.4:1 Input Power Vss=Gnd Vss= -3 Two-Tone Inputs Up To + 5 dBm Vss=Gnd Vss= -3 10% To 90% 50% Cntl To 90%/10%Rf In-Band 1.0 GHz 1.0 GHz 21 29 dBm dBm 2.0 GHz 2.0 GHz 35 35 10 20 10 dBm dBm nS nS mV ________________________________________________________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 1 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 DC Electrical Specifications @ + 25oC Parameter Single VDD Supply Voltage VSS Idd CMOS Logic Level (0) CMOS Logic Level (1) Input Leakage Current * Performance curves are for Vdd = +5.0 +/- 10% Minimum 3.3* Typical 5.0 .07 0 VDD - 0.8 Maximum 5.5 -5.0 10 0.8 VDD 10 Units V V uA V V uA Absolute Maximum Ratings1 VDD Parameter Absolute Maximum +6.0 Units V VSS -5.5 V Vin Digital Logic 0 - 0.6 V Vin Digital Logic 1 Vdd + 0.6 V Maximum Input Power > 35 dBm ESD Voltage 400 V Operating Temperature Range +85 Degrees C Storage Temperature Range +125 Degrees C (Note 1) Operation beyond any of these parameters may cause permanent damage. Latch-Up: Unlike conventional CMOS RF switches, Honeywell's HRF-SW1001 is immune to latch-up. ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be taken to ensure that the Absolute Maximum Ratings are not exceeded. Package Outline Drawing Bottom View, 12 Pin 3X3 mm LPCCTM Package ASAT LPCC Marketing Outline Dwg. # GMJ00004 For more information see http://www.asat.com 3 mm 3 mm _________________________________________ _______________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 2 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Truth Table Switch Control RF Output 1 RF Output 2 0 RF INPUT --- 1 --- RF INPUT "0" = CMOS Low, "1" = CMOS High Pin Configuration Pin Function Pin Function 1 2 3 4 5 6 GROUND RF OUT 2 GROUND VDD SWITCH CONTROL VSS 7 8 9 10 11 12 GROUND RF OUT 1 GROUND GROUND RF IN GROUND Note: Bottom ground plate must be grounded for proper RF performance. Evaluation Circuit Board Connections RF In HRF-SW1001 Evaluation Board Top View RF Out2 RF Out1 Honeywell HRF-SW1001 VSS VDD Ground SW Control Ground ________________________________________________________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 3 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Performance Curves Insertion Loss Insertion Loss Versus Frequency Insertion Loss (dB) 0.0 The Insertion Loss curve shows the typical return loss versus frequency at Vdd = +5.0 +/- 10%, Ta = 25C, Z0 = 75 Ohms -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Frequency (GHz) Isolation Isolation [dB] Isolation Versus Frequency -20.0 -30.0 -40.0 -50.0 -60.0 -70.0 -80.0 -90.0 -100.0 The Isolation curve shows the typical isolation of an "off" state output to the insertion path. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency [GHz] ________________________________________________________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 4 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Return Loss Input/Output Return Losses Versus Frequency 0 The return loss curve shows the input return loss S11 and the output return loss in the insertion path S22. Return Loss [dB] -5 -10 -15 S22 -20 S11 -25 -30 -35 -40 0 0.5 1 1.5 Frequency [GHz] 2 2.5 3 Evaluation Circuit Board Honeywell's evaluation board provides an easy to use method of evaluating the RF performance of our switch. Simply connect power, DC and RF signals to be measuring switch performance in less than 10 minutes. HRF-SW1001 Evaluation Board ________________________________________________________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 5 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Evaluation Circuit Board Layout Design Details Item PCB Switch Chip Capacitor RF Connector DC Pin Description Impedance Matched Multi-Layer FR4 HRF-SW1001 RF Switch Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector Mil-Max Model 800-10-064-10-001 Header Pins Ordering Information Ordering Number HRF-SW1001-B HRF-SW1001-TR HRF-SW1001-E Product Delivered In Chip Tubes Delivered On Tape And Reel2 Engineering Evaluation Board (Note 2) Contact Honeywell for details LPCCTM is a registered Trademark of ASAT Ltd. Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. ________________________________________________________________________________________________________ Web Site: Email: www.mysoiservices.com mysoiservices@honeywell.com 2002 1001W Published February 2003 Page 6 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295